Beruflich Dokumente
Kultur Dokumente
Issue 18
Page 1 of 12
March 2013
Aerospace series
Sleeve - One way reinforced, coupling,
air circulation pipes
When this standard is applied, a careful check must be made as to whether any protective rights exist. This
standard issuer hereby disclaims any liability for infringement of patent or design rights resulting from the use of
this standard.
Copyright reserved
Ref. no. ABS0059
ABS0059 Page 2
Issue 18
Contents
1 Scope
2 Normative references
3 Requirements
4 Designation
5 Marking
6 Technical specification
ABS0059 Page 3
Issue 18
1 Scope
This standard specifies the dimensions, tolerances, required characteristics and the mass of a sleeve for coupling
of two ducts, air conditioning.
2 Normative references
This Airbus Standard incorporates by dated or undated reference provisions from other publications. All normative
references cited at the appropriate places in the text are listed hereafter. For dated references, subsequent
amendments to or revisions of any these publications apply to this Airbus Standard only when incorporated in it by
amendment of revision. For undated references, the latest issue of the publication referred to shall be applied.
3 Requirements
1
Published by: Society of Automotive Engineers (SAE), 400 Commonwealth Drive, Warrendale, PA 15096-0001, USA
2
Published by: Department of Defense (DoD), the Pentagon, Washington, D.C., 20307, USA
ABS0059 Page 4
Issue 18
Table 1: Tolerances
Dimensions in millimeter.
Duct external diameter
Tolerances on diameter
ØD
r 4,5
r 7,5
See note 1
E E
Dimensions in millimeter.
Note 1: The sleeve elasticity should allow the assembly on smooth end or end following MS33660 (AS5131)
standard.
C
r 4,5
r 7,5
AxB
A
B
E E
A
Dimensions in millimeter.
Figure 3: Configuration, dimensions and tolerances
ABS0059 Page 8
Issue 18
Section A-A
L±3
A
,5
r4
r7
C
,5
R2
B E E
Dimensions in millimeter.
Figure 4: Configuration, dimensions and tolerances of Oval duct
ABS0059 Page 10
Issue 18
A Section A-A
G L± 3
,5
r4
C
r7
,5
R2
R3
A E E
Dimensions in millimeter.
Figure 5: Configuration, dimensions and tolerances of Oval duct
3.2 Material
Silicon-coated fiberglass plies per ABD0007 paragraph 2.2.4.1 and 2.2.4.2 conform to ABD0031.
4 Designation
This type of Standard shall be designated according to the philosophy of the following example:
5 Marking
Unless otherwise specified by contract, marking shall include :
6 Technical specification
ABS0081.
ABS0059 Page 13
Issue 18
RECORD OF REVISIONS
Clause
Issue Description of modification
modified
1 New Standard.
03/92
2 Standard amended
07/96
3 Standard amended
10/98
4 Standard amended
05/99
8 Item Nos 202, 206, 208, 210, 212, 214, 222, 225, 226, 228, 229, 230, 233, 235,
237, 251, 253, 255, 260, 264, 266, 267 and 268 added.
08/05
Figure 2 added.
Table 2 : Item Nos 300 to 306 and 400 to 405 added.
Table 3 added.
“Table 1” changed in “Table 2”.
“Table 1 : Tolerances” added.
Table 2 : Item Nos 202, 206, 208, 210, 212, 214, 222, 225, 226, 228, 229, 230,
233, 235, 237, 251, 253, 255, 260, 264, 266 and 268 deleted.
Item No. 267 modified.
Figure 2 (Definition of elliptical duct) modified.
Table 3 : Item Nos 300 to 306 and 402 to 405 deleted.
Table 4 : Item Nos “300 to 399” deleted.
Figures 1 and 4 added.
Table 4 added.
Tables modified : Item Nos added.
Table 2 : Item No. 258 added and Item No. 224 modified.
Table 2 : Item No. 313 added.
Table 3 : Item Nos 505 and 506 added.
Template updated.
ABS0059 Page 14
Issue 18
Clause
Issue Description of modification
modified
02/08
07/08
11/09
10/10
04/11
06/11
18 Figures 2, 3, 4, Tolerances amended for dimension „L‟ and cuffed end thickness
and 5
03/13