Beruflich Dokumente
Kultur Dokumente
Rev. 4/06
Achiever™ Products, A Division of the Dunbarton Corporation
868 Murray Road, Dothan, AL 36303
Toll Free: (800) 633-7553 Tel: (334) 794-0661 Fax: (334) 793-7022
Web Page: www.dunbarton.com E-mail: sales@dunbarton.com
1
BEFORE YOU BEGIN Step 2
Apply sealant
PLEASE FOLLOW ALL INSTRUCTIONS AND ALWAYS USE Apply weather seal putty or Mounting
PROTECTIVE EYEWEAR WHEN INSTALLING A DOOR SYSTEM.
PLEASE READ INSTRUCTIONS COMPLETELY.
silicone to the mounting Flange
Apply a line of
putty / silicone
across underside
FIGURE 2A of threshold.
Step 3
OPENING HEIGHT
Step 4
2'8" 33-5/8" 78" 80" 82-1/4"
Install Screws
3'0" 37-5/8" 78" 80" 82-1/4"
Install four (4) #8 x 1" wood attachment screws,
one in each corner and check for proper fit of
the unit (Figures 3, 3A). Refer to Step 11 if
installing mounting screw cover.
INSTALLATION
Step 1
Remove door from packaging. Move to
install area; assemble tools & materials
• Safety glasses
• Level
• Tape measure
• Phillips head screwdriver
• Square head screwdriver Installation
• Weather Seal Putty or Silicone Screw Holes
FIGURE 4A FIGURE 4
2
Step 5 FIGURE 7A
Remove Prehang Material
Remove tie strap from door latch
bore. Open door and remove
margin spacing clips (Figure 5).
FIGURE 7B
Step 6 Step 8
Adjust Doors to Opening Install Strike Security Screws
Plumb hinge side using level and LATCH: Remove #6 strike screw from bottom
t-square; make any necessary hole in latch strike plate. Install #6 x 1-1/2" long
adjustments to verify FIGURE 5 wood security screw in BOTTOM hole. Shim if
squareness/placement of the frame necessary (Figure 8).
(Figure 6 and 6A). Install the balance of the
#8 x 1" wood attachment screws into every hole.
Refer to Step 13 if installing mounting screw
cover.
FIGURE 8
Shim
(Hinge)
Caulk line
at header/
upright
Caulk
line at
Shim threshold
(Hinge)
Shim
(Strike)
Shim
(Hinge) FIGURE 9
3
Step 10
Trim out the interior and exterior. WARRANTY
EXTERIOR SIDE: Vinyl siding may overlap
The Warranty for Steel Frames manufactured by ACHIEVER™
mounting flange or fit flush around perimeter. PRODUCTS DIVISION is to the original consumer purchaser to
be free from defects in material and workmanship for a period of
INTERIOR SIDE: Add trim around door so that it one (1) year from the date of purchase.
overlaps frame return (Figures 10, 10A). This warranty is applicable only when the product(s) covered by
it have been installed in accordance with the recommended
written installation instructions of ACHIEVER™ PRODUCTS
DIVISION and with established building practices, have been
accorded treatment which is considered good practice in the
building industry regarding storage and maintenance, and have
been subject only to normal use. Because ACHIEVER™
PRODUCTS DIVISION cannot control the manner in which its
products are handled after leaving its premises, this warranty
does not apply to the finish or accessories of any product.
FIGURE 10 FIGURE 10A ANY AND ALL IMPLIED WARRANTIES HERETO ARE LIMITED
TO ONE (1) YEAR FROM THE DATE OF PURCHASE.
Rev. 4/06
Achiever™ Products, A Division of the Dunbarton Corporation
868 Murray Road, Dothan, AL 36303
Toll Free: (800) 633-7553 Tel: (334) 794-0661 Fax: (334) 793-7022
Web Page: www.dunbarton.com E-mail: sales@dunbarton.com