1 For security, please read the instruc�ons carefully before ini�al opera�on; making sure the power is off before connec�on. CN1 CN2 2 Please clear the memory before ini�al opera�on. (Ref. Erasing ALL learned / memorized transmi�ers) 3 Do not learn the remote control when the motor is opera�ng in order to avoid mis-opera�on. L Power L line Photocell receive module power terminal + 4 The received signal may be interfered by other communica�on devices. (e.g. the wireless N Power N line Photocell transmit module power terminal + control system with the same frequency range) 5 It is forbidden to control the high-risk coefficient equipment / system. (e.g. cranes) EG Ground wire GND Photocell transmit&receive module power terminal - 6 It is used only for the manual remote control and wireless control equipment / system which EG Ground wire Infrared contactor (NC) must not endanger life or property during running failure, or its security risks have been eliminated Technical Data COM Motor COM Open(NO)
L Down line Stop(NO)
Power 85-265VAC 50HZ/60HZ Weight 242g L Up line Close(NO) Loading capacity 1HP/230VAC or 0.5HP/110VAC Flash lamp Single bu�on control(NO) Temperature -20C to 60C IP 56 外 COM Public port Transmi�er stored Rolling 30;Fixed 60 Built-in fuse F10A Size(mm) 150(L)*100(W)*40(H) Frequency 433.92Mhz External 3 bu�ons control External 1 bu�on control Control bu�on PCV bu�on, external switch and remote control CE cer�fica�on EN300220-1,EN301489-1,EN62479,EN60950-1 DIP swich Func�on 1, Learning transmi�ers:Press the learning bu�on in the control board, LED is on, enters into the learning process; Press the same bu�on twice, LED blinks for several �mes, then off. The learning process is successful. 2, Use the transmi�er that already has been learned as old transmi�er, press bu�on 1 NO Clockwise Single bu�on Flashing Deadman External self-lock switch (Deadman) Photocell connec�on and bu�on 2 at the same �me. Then press bu�on 2 to let it enters into the learning OFF An�clockwise Three bu�ons Keep ligh�ng Impulse 行,点按按 停止。 process. Press the same bu�on on the new transmi�er twice. The learning process is finished. In this way new transmi�er can be learned without pressing the learning Transmiter Opera�on 3. 外保 功能: 外在 起作用, 程中, 外 被 bu�on on the control board. 1, Single bu�on (Open-stop-close-stop); Three bu�on (Open, 3, Erasing transmi�er: Press the learning bu�on, con�nue pressing for 8s un�l LED stop, close). 工作off; Release 5.turns 定:控制器可 置 LED learning bu�on, 移will be on (5-(about 可and):按下【TIME】 100S1s) then off; the erasing 学Deadman 2, 功能。 model: [ 操作方法:同Door moves按住旧遥控器的① ,再按② +② bu�on when keep pressing and , process is successful. 按 ,用秒表 始 (大于 5S 后【TIME】LED 始 亮),等待所需 学 指示灯 LED stops when 色, 入学 状 , release; Impulse model: Press 次按下新要控器同一 bu�on and door 4, Bu�on 1,2,3 in transmi�er is in correspondence with open, close and stop.(The same moves, press bu�on and door stops Power, Motor, Flash lamp connec�on 定as bu�on 后松 按 ,即 置成功。 on controller and the external three bu�on control); Single-bu�on control is 按 ,LED 持 数秒 ,学 成功。 3, Infrared protec�on: It only work when door closing. Motor 控制器 6.only effec�ve自学to the功能;配遥控器最大 learned bu�on(The same距离可 as external50m 。 circle control).If a new 3. stops single 除遥控器:when photocell 按下学signal 按 ,学 指示灯 disconnec�ng during 色 8S 后 LEDdoor closing. bu�on of transmi�er learned into the control panel, the formal one is useless 4, Flash lamp: Ligh�ng or blinking (frequency is 60 �mes) is Model List op�onal ,松 学 when按 motor is running LED 亮 色 1S 后 ,完成 除遥控器。 5, Running �me set up: Motor running �me is adjustable from 5s 4. 学 好的遥控器三 控制:1、2、3 分 、停、 功能(等 Model TM5801 TM5803 TM5811 TM5813 to 100s. Press 【TIME】 and LED will blink a�er 5s, then release Color White White Black Black 同the bu�on PVC按 控制和外接三 a�er the 控制); pre-set �me is 控制:只有学 appropriate . 的按 6, Self-learning 起作用(等同外接 func�on; Max remote distance 循 控制),同一遥控器只可以学 一个按 。 over 50 M code Rolling Fixed Rolling Fixed The interpreta�on and ownership of this manual belong to Any change of the product can be without prior no�ce.