Beruflich Dokumente
Kultur Dokumente
2 DORMA
LM TECHNICAL DETAILS SPECIFICATIONS
Certification
..The DORMA LM
Center hung pivots will accom- Cross Reference Chart
modate double-acting and DORMA Rixson
Series is listed by UL single-acting doors. Center hung OP440 117
and CUL under their continu- single-acting doors will use an OPF440 F117
..
ing reinspection programs. applied stop. OPJ350 195
The LM Series is OPH750 117-1/2
certified to the Pocket pivots will accommodate OPHF750 F117-1/2
requirements of doors opening 90º that must be OPL440 L147
ANSI/BHMA A156.4. flush with an adjacent wall. OPL800 L117
OP15200 117 × 1-1/2"
Specification All pivots and pivot sets will OP15500 117-1/2 × 1-1/2"
DORMA's LM Series pivots are incorporate needle bearings and OPF15200 F117 × 1-1/2"
produced from brass or steel for lubricated hardened steel pivot OPF15500 F117-1/2 × 1-1/2"
interior and exterior non-rated pins treated to prevent corrosion. CP440 370
and fire-rated doors. CPA440 370
All pivots and pivot sets will be CP660 117–3/4
Top pivots and bottom arms will available in a variety of finishes. CP1000 H117–3/4
be center hung, 3/4" or 1-1/2"
NOTE: Comparison is based upon application type and maximum door weight
offset. Finishes
capacity, which may vary between manufacturers. Based on information obtained
from trade sources, it is our judgment that these products are most similar. Exact
Plated Finishes
..
Intermediate pivots will be 3/4" equivalency is not guaranteed.
..
or 1-1/2" offset. Side jamb Primed for Painting: 600.
bottom pivot will be 3/4" offset. Brass: 605 (Bright) or
..
606 (Satin).
Optional DORMA Custom Color
Top and intermediate pivots will Bronze: 611 (Bright),
or Designer Color Finishes
be full mortise configurations. 612 (Satin), or 613 (Oxidized
Contact Customer Service.
..
Satin Oil Rubbed).
Bottom arms and side jamb pivot Nickel: 618 (Bright) or
Warranty
..
will be mortised. 619 (Satin).
For details, refer to DORMA
Chrome: 625 (Bright) or
Limited Warranty Policy on our
Pivots can be substituted within 626 (Satin).
website at go.dorma.com/terms.
a pivot set, assuming the offset is
Sprayed Finishes
..Aluminum: 689.
the same.
..
inset 1/8" from the frame face 695 (Dark Duranodic).
..
while standard intermediate and Gold: 696.
bottom arms are templated Black: 693.
accordingly.
DORMA 3
LM APPLICATIONS
APPLICATIONS
—
Center Hung – Single or Double Acting 3/4" Offset Hung – Single Acting
2-3/4"
3/4"
13/16"
Pivot
Door closed
Door in pocket
(1/8" inset door) 1-3/8"
1-1/2"
13/16"
All bottom arms and floor bearings, excluding the 75320 side jamb pivot, can be used NFPA 80 requires that labeled fire doors up to 60" in height be provided with 2
on fire doors. Top and intermediate pivots for 20 minute rated and up to 3 hour rated pivots and an additional pivot for each 30" of door height or fraction thereof. The
doors can be assembled with a bottom arm and floor bearing of common application same recommendation applies for non-labeled doors. Distance between pivots
to create specialty fire rated sets. See component drawings for specific details on the may exceed 30".
standard, fire rated, lead-lined, and electrified components and their compatibility in
the various applications.
4 DORMA
LM APPLICATION DRAWINGS
2
4
3
3
2
2
3
3
DORMA 5
LM APPLICATION DRAWINGS
3 (Specify Hand)
6 DORMA
LM APPLICATION DRAWINGS
2
1 75140 Top Pivot
2
2 75343 Bottom Arm
3
5 7471HD Floor Bearing
5
4 75240 Intermediate
Pivot (optional)
(Specify Hand)
DORMA 7
LM APPLICATION DRAWINGS
3 (Specify Hand)
8 DORMA
LM COMPONENT DRAWINGS
CENTER HUNG
—
1-7/16 C 1-3/8
(37) (35)
1/4
B (6)
25/32 13/32
.591 A (20) (10)
(15) Bottom of frame
Top of door A. 1/8" clearance
2-3/4
B. 3/8" clearance
(70) 2-3/4
C. 3/4" clearance
1-11/16 2-7/8 (70)
(43) (73)
15/16
(24)
1
6-1/2
(25)
(165)
1-5/32 4-25/32 1-3/8
(29) (121) (35)
9-1/4
(235)
7/16
(11)
No. 8062 — Walking beam top pivot with cover plate. Lateral No. 7421 — Center hung bottom arm for steel or wood doors. For use
adjustment assures the door is plumb. Accommodates top door with 7471K and 7471HD floor bearing.
clearances of 1/8", 3/8", or 3/4". Optional extended pin available for
clearances of 3/4", 1", or 1-5/16". Not recommended for use with
overhead stops/holders. Use HD8062.
25/32 13/32
(20) (10)
2-3/4
(70) 2-7/32
15/16 Max.
(24) (56)
1-3/8 1-1/4
Min.
(35) (32)
9-1/4
(235)
No. 7422 — Center hung bottom arm for aluminum doors. For use
with 7471K and 7471HD floor bearing.
DORMA 9
LM COMPONENT DRAWINGS
CENTER HUNG
—
1-3/8
1-7/16
(35)
(37)
1/4
(6)
5/8 1-7/16 C 1-3/8
(16) (37) (35)
Bottom of frame
Top of door 1/4
B (6)
2-3/4 A
1/2
(70) (13) Bottom of frame
1-11/16 2-7/8
(43) (73) Top of door
A. 1/8" clearance
2-3/4
B. 3/8" clearance
(70)
1 C. 3/4" clearance
6-1/2 1-11/16 2-7/8
(25) (43) (73)
(165)
1-1/4 6
(32) (152)
1
6-1/2
(25)
(165)
3/4
(19)
HD8062 — Heavy-duty walking beam top pivot with frame portion and 8062.5 — Walking beam top pivot frame portion with cover plate.
cover plate. Door portion consists of a needle bearing pressed into a Pin has a 1/2" diameter.
3/4" thick aluminum block. Adjustable to obtain a 1/8"–3/8" clearance
between the door and frame. Required when using overhead
stops/holders.
1
6-1/2
(25)
(165)
1-1/4 6
(32) (152)
Electrical
Component
3/4
(19)
10 DORMA
LM COMPONENT DRAWINGS
4-1/4 5/16
13/16
(108) (8)
(21)
3/4 5/16
(19) 3/4 (8)
(19)
1-1/16
(27)
3/4 3/4
(19) (19)
13/16
(21)
5 5
3/4 (127) (127)
1/4
(19)
(6)
3/4 1/4
1-1/8 1-1/8
(19) (6)
(29) (29)
No. 75120 — 3/4" offset standard brass top pivot. No. 75220 — 3/4" offset standard brass intermediate pivot.
No. 75122 — 3/4" offset brass top pivot. U.L. listed for 20 minute No. 75222 — 3/4" offset brass intermediate pivot. U.L. listed for 20
rated fire doors. minute rated fire doors.
No. 75133 — 3/4" offset steel top pivot. For use on fire doors rated up No. 75233 — 3/4" offset steel intermediate pivot. For use on fire
to three hours. doors rated up to three hours.
(Specify Hand)
Note: Standard pivots are non-handed and designed for flush door and
frame conditions. For 1/8" inset pivots, add 5/8 suffix and hand, i.e.
75120 5/8 RH.
6-3/8
(162)
13/16
(21)
3/4
13/16 13/32
(21) (10)
DORMA 11
LM COMPONENT DRAWINGS
5/16
3/4 3/4 (8)
3/4 (19) (19) 3/4
13/16 (19)
(19)
(21)
1-1/8
5/16
(29)
(8)
4-3/4
3/8 2-1/2 2-1/2
(121)
(10) (64) (64)
No. 75320 — 3/4" offset brass bottom side jamb pivot. For use with No. 75210 — 3/4" offset light-duty brass intermediate pivot. Non-load
doors weighing up to 350 lb. Has a vertical height adjustment of 3/8". bearing, for door alignment only.
(Specify Hand) (Specify Hand)
5 5 1-5/8
(127) (127)
(41)
3/4
3/4 (19)
1-1/8 1-1/8
13/16 (19)
(29) (29)
(21)
1/2
(13)
Electrical
Component 1/4
3/4 (6)
(19)
No. 75200 — Electrified intermediate pivot for power transfer. No. 75120/102 — Standard mortised door portion with a pivot block
Available as an eight-wire design using #28 AWG, rated for 24 V containing a needle bearing mortised into the overhead condition
maximum. Pairs of wires connected together provide 2 A maximum. above. This pivot is ideal for conditions when the door is inset from the
Multiple pairs provide greater amperage ratings, i.e. two pairs in a frame face, or the ceiling is directly above the door.
circuit provide 4 A maximum and four pairs provide 8 A maximum. (Specify Hand)
Pivot is non-load bearing and has non-separable pivot leaves.
(Specify Hand)
12 DORMA
LM COMPONENT DRAWINGS
13/16 5/16
4-1/4 (21) (8)
(108)
No. 75140 — 3/4" offset brass top pivot for lead-lined doors No. 75240 — 3/4" offset brass intermediate pivot for lead-lined doors
1-3/4" thick. 1-3/4" thick.
No. 75142 — 3/4" offset brass top pivot for lead-lined doors No. 75242 — 3/4" offset brass intermediate pivot for lead-lined doors
1-3/4" thick. U.L. listed for 20 minute rated fire doors. 1-3/4" thick. U.L. listed for 20 minute rated fire doors.
No. 75143 — 3/4" offset steel top pivot for lead-lined doors No. 75243 — 3/4" offset steel top pivot for lead-lined doors
1-3/4" thick. For use on doors rated up to three hours. 1-3/4" thick. For use on doors rated up to three hours.
NOTE: For doors 2" to 3" thick specify as follows NOTE: For doors 2" to 3" thick specify as follows
No. 75140 – 2 — For use on doors 2" thick. No. 75240 – 2 — For use on doors 2" thick.
No. 75140 – 2-1/4 — For use on doors 2-1/4" thick. No. 75240 – 2-1/4 — For use on doors 2-1/4" thick.
No. 75140 – 2-1/2 — For use on doors 2-1/2" thick. No. 75240 – 2-1/2 — For use on doors 2-1/2" thick.
No. 75140 – 3 — For use on doors 3" thick. No. 75240 – 3 — For use on doors 3" thick.
(Specify Hand)
NOTE: Standard pivots are non-handed and designed for flush door
and frame conditions. For 1/8" inset pivots, add 5/8 suffix and hand,
i.e. 75140-2 5/8 RH.
No. 75343 — 3/4" offset standard steel bottom arm for lead-lined 1-3/4"
7-3/4 doors. Can also be used on fire doors rated up to 3 hours. For use with
(197) 7471K and 7471HD floor bearing.
“A”
NOTE: For doors 2" to 3" thick specify as follows
No. 75343 – 2 — For use on doors 2" thick.
3/4 No. 75343 – 2-1/4 — For use on doors 2-1/4" thick.
Cover (19) Door Size “A” No. 75343 – 2-1/2 — For use on doors 2-1/2" thick.
3/4
1-3/4" 1-1/4"
(19) No. 75343 – 3 — For use on doors 3" thick.
13/16 2" 1-3/8"
2-1/4" 1-1/2" (Specify Hand)
(21)
2-1/2" 1-5/8"
3" 2"
13/16 1/2
(21) (13)
DORMA 13
LM COMPONENT DRAWINGS
3/4
13/16 (19) 5 5
(21) (127) (127)
3/4
(19) 1/4
(6)
1/4
1-1/8 1-1/8
3/4 (6)
(29) (29)
(19)
No. 15120 — 1-1/2" offset standard brass top pivot. No. 15220 — 1-1/2" offset standard brass intermediate pivot.
No. 15122 — 1-1/2" offset brass top pivot. U.L. listed for 20 minute No. 15222 — 1-1/2" offset brass intermediate pivot. U.L. listed for
rated fire doors. 20 minute rated fire doors.
No. 15133 — 1-1/2" offset steel top pivot. For use on fire doors rated No. 15233 — 1-1/2" offset steel intermediate pivot. For use on fire
up to three hours. doors rated up to three hours.
(Specify Hand)
NOTE: For 1/8" inset pivots, add 5/8 suffix, i.e. 15122 5/8.
1-3/8
(35)
Cover
1-1/2
3/4 (38)
13/16 (19)
(21) 12
(305)
13/16 11/32
(21) (9)
No. 15323 — 1-1/2" offset standard steel bottom arm. Can also be
used on fire doors rated up to 3 hours. For use with 7471K and
7471HD floor bearing.
(Specify Hand)
14 DORMA
LM COMPONENT DRAWINGS
FLOOR BEARINGS
—
Floor Bearing Spindle Height Clearance Provided Under Door
7471K 3/4"*
2-9/16 1-13/32
7471K × 5 mm 15/16"
(65) (36)
1-3/32 7471K × 10 mm 1-1/8"
(28)
7471K × 15 mm 1-5/16"
1-25/32
7471K × 20 mm 1-1/2"
(45)
7471K × 25 mm 1-11/16"
7471K × 30 mm 1-15/16"
23/32 7471K × 35 mm 2-1/8"
(18)
7471K × 40 mm 2-5/16"
7471K × 45 mm 2-1/2"
5/32
(4) 7471K × 50 mm 2-11/16"
* Lesser clearances can be obtained by altering the mortise depth of the arm
No. 7471K — Standard floor bearing with thrust roller bearing for
doors weighing up to 440 lb. Can also be used on fire doors rated up
to 3 hours. Includes cover cap. Mounts directly to floor. For use with
No. 75323, 75343, 7421, 7422 and 15323 bottom arms. Available
with integral spindle extensions as shown in the adjacent chart.
13/16
(21) 5-3/16
(132)
DORMA 15
POCKET PIVOTS
—
For use on doors up to 4'-0"
1-7/8
wide and weighing up to 300 lb
(48) 3/16 1-17/32
(5) 3/16
when hung on three pocket
(39)
(5)
pivots. Allows for maximum door
swing of 90º
6-1/4
(159) DORMA offers pocket door
1-5/8 1-5/8 5-1/2
(41) (41) (140) packages for surface door
closers and floor concealed
closers. See individual door
7/8 closer brochures for surface
(22) 1-23/32 closer details or BTS Series
1-11/32 (44) brochures for floor concealed
(34)
closer details.
Pivot 1-3/4
Only
(44) No. 75520 — Bronze pocket
pivot. For 90º pocket doors.
Door closed
No. 75523 — Steel pocket pivot
for 90º pocket doors, U.L. listed
Door in pocket for 20 minute wood doors and
3 hour rated steel fire doors.
.Pocket
.Door surface
Pivot Hung Door
is flush with .Conventional
.Door edge protrudes
Hinged Door
into
..Open door fits completely into ..Door edge and hinge interfere
..No dirt or debris build-up ..Dirt and debris build-up
hatched recessed wall pocket with traffic
maintenance