Beruflich Dokumente
Kultur Dokumente
html
2019 Latest lead4pass 200-125 PDF and VCE dumps Download
200-125Q&As
CCNA Cisco Certified Network Associate CCNA (v3.0)
Free Download Real Questions & Answers PDF and VCE file from:
https://www.lead4pass.com/200-125.html
QUESTION 1
Which statement describes the effect of the copy run start command on a router in enable mode?
A. The running configuration of the router is savedto NVRAM and used during the boot process.
B. The router reboots and loads the last saved running configuration.
C. A copy of the running configuration of the router is sent by FTP to a designated server.
Correct Answer: A
Explanation
QUESTION 2
Which command can you execute to set the user inactivity timer to 10 seconds?
A. SW1(config-line)#exec-timeout 0 10
B. SW1(config-line)#exec-timeout 10
C. SW1(config-line)#absolute-timeout 0 10
D. SW1(config-line)#absolute-timeout 10
Correct Answer: A
Explanation
QUESTION 3
Which two components are used to identify a neighbor in a BGP configuration? (Choose two.)
B. version number
C. router ID
D. subnet mask
E. IP address
Correct Answer: AE
Explanation
Use the show ip bgp neighbors (registered customers only) command to display information about the TCP and Border
Gateway Protocol (BGP) connections and verify if the BGP peer is established. The output of the show ip bgp neighbors
command below shows the BGP state as \\'Established\\', which indicates that the BGP peer relationship has been
established successfully. R1-AGS# show ip bgp neighbors | include BGP BGP neighbor is 10.10.10.2, remote AS 400,
internal link BGP version 4, remote router ID 2.2.2.2 BGP state = Established, up for 00:04:20 BGP table version 1,
neighbor version 1 R1-AGS# The show ip bgp neighbors command has been used above with the modifier | include
BGP. This makes the output more readable by filtering the the command output and displaying the relevant parts only.
In addition, the show ip bgp summary (registered customers only) command can also be used to display the status of all
BGP connections, as shown below. R1-AGS(9)# show ip bgp summary BGP router identifier 10.1.1.2, local AS number
400 BGP table version is 1, main routing table version 1
Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd 10.10.10.2 4 400 3 3 1 0 0 00:00:26 0
QUESTION 4
A switch has 48 ports and 4 VLANs. How many collision and broadcast domains exist on the switch (collision,
broadcast)?
A. 4,48
B. 48,4
C. 48,1
D. 4,1
E. 1,48
Correct Answer: B
QUESTION 5
What is the result of issuing the frame-relay map ip 192.168.1.2 202 broadcast command?
A. defines the destination IP address that is used in all broadcast packets on DCLI 202
B. defines the source IP address that is used in all broadcast packets on DCLI 202
C. defines the DLCI on which packets from the 192.168.1.2 IP address are received
D. defines the DLCI that is used for all packets that are sent to the 192.168.1.2 IP address
Correct Answer: D
This command identifies the DLCI that should be used for all packets destined to the 192.168.1.2 address. In this case,
DLCI 202 should be used.
QUESTION 6
Which two statements are true about interVLAN routing in the topology that is shown in the exhibit? (Choose two.)
C. Router1 will not play a role in communications between host A and host D.
E. Router1 needs more LAN interfaces to accommodate the VLANs that are shown in the exhibit.
F. The FastEthernet 0/0 interface on Router1 and the FastEthernet 0/1 interface on Switch2 trunk ports must be
configured using the same encapsulation type.
Correct Answer: DF
In order for multiple VLANs to connect to a single physical interface on a Cisco router, subinterfaces must be used, one
for each VLAN. This is known as the router on a stick configuration. Also, for any trunk to be formed, both ends of the
trunk must agree on the encapsulation type, so each one must be configured for 802.1q or ISL.
QUESTION 7
Which two statements describe key differences between single- and dual-homed WAN connections? (Choose two)
B. Dual-homed WAN connections have more management-application overhead than single-homed connections.
C. Dual-homed WAN connections require more skill to administer than single-homed connections.
E. Dual-homed WAN connections have higher WAN speed than single- homed connections.
Correct Answer: AC
Explanation
QUESTION 8
Which two characteristics of an ICMP echo-based IP SLA are true? (Choose two)
D. It measures traffic to determine the reliability of a connection from a Cisco router to a designated end device.
Correct Answer: DE
Explanation
QUESTION 9
Correct Answer: C
Explanation
Switches dynamically learn MAC addresses based on the source MAC addresses that it sees, and since a broadcast is
never the source, it will never learn the broadcast address.
QUESTION 10
You have configured the host computers on a campus LAN to receive their DHCP addresses from the local router to be
able to browse their corporate site. Which statement about the network environment is true?
Correct Answer: A
QUESTION 11
Refer to exhibit: Which two destination addresses will be used by Host A to send data to Host C? (Choose two.)
Correct Answer: CF
While transferring data through many different networks, the source and destination IP addresses are not changed. Only
the source and destination MAC addresses are changed. So in this case Host A will use the IP address of Host C and
the MAC address of E0 interface to send data. When the router receives this data, it replaces the source MAC address
with its own E1 interface\\'s MAC address and replaces the destination MAC address with Host C\\'s MAC address
before sending to Host C.
QUESTION 12
Which IEEE standard protocol is initiated as a result of successful DTP completion in a switch over Fast Ethernet?
A. 802.3ad
B. 802.1w
C. 802.1D
D. 802.1Q
Correct Answer: D
Dynamic Trunking Protocol (DTP) is a Cisco proprietary protocol for negotiating trunking on a link between two devices
and for negotiating the type of trunking encapsulation (802.1Q) to be used.
QUESTION 13
A. 172.31.255.100
B. 12.17.1.20
C. 172.15.2.250
D. 10.172.76.200
E. 192.109.32.10
Correct Answer: AD
QUESTION 14
What Cisco IOS feature can be enabled to pinpoint an application that is causing slow network performance?
A. SNMP
B. Netflow
C. WCCP
D. IP SLA
Correct Answer: B
Explanation
Netflow can be used to diagnose slow network performance, bandwidth hogs and bandwidth utilization quickly with
command line interface or reporting tools. Reference: http://www.cisco.com/c/en/us/products/collateral/ios-nx-os-
software/iosnetflow/prod_white_paper0900aecd80406232.html
QUESTION 15
A. The configuration that is shown provides inadequate outside address space for translation of the number of inside
addresses that are supported.
B. Because of the addressing on interface FastEthernet0/1, the Serial0/0 interface address will not support the NAT
configuration as shown.
C. The number 1 referred to in the ip nat inside source command references access-list number 1.
D. ExternalRouter must be configured with static routes to networks 172.16.1.0/24 and 172.16.2.0/24.
Correct Answer: C
Explanation
QUESTION 16
A. FCS
B. SOF
C. SA
D. DA
Correct Answer: C
QUESTION 17
Correct Answer: D
The "show ip ospf database" command displays the link states. Here is an example:
QUESTION 18
A. 1111110
B. 1111111
C. 00000000
D. 1111100
Correct Answer: A
QUESTION 19
Which two QoS tools can you use to guarantee minimum bandwidth to certain traffic? (Choose two)
A. WFQ
B. RSVP
C. LLC
D. FIFO
E. CBWFQ
Correct Answer: AE
QUESTION 20
Which two EXEC mode commands can simplify DHCP lease management? (Choose two)
A. release dhcp
C. Renew dhcp
D. ip address dhcp
Correct Answer: AC
Explanation
QUESTION 21
After completing the configuration, the associate discovers that not all the interfaces are participating in OSPF. Which
three of the interfaces shown in the exhibit will participate in OSPF according to this configuration statement? (Choose
three.)
A. FastEthernet0 /0
B. FastEthernet0 /1
C. Serial0/0
D. Serial0/1.102
E. Serial0/1.103
F. Serial0/1.104
Explanation
The "network 192.168.12.64 0.0.0.63 equals to network 192.168.12.64/26. This network has:
Increment: 64 (/26= 1111 1111.1111 1111.1111 1111.1100 0000) + Network address: 192.168.12.64
Therefore all interfaces in the range of this network will join OSPF.
QUESTION 22
Which command can you enter on a switch to determine the current SNMP security model ?
Correct Answer: B
Explanation: show snmp groupTo display the names of groups on the router and the security model, the status of the
different views, and the storage type of each group, use the show snmp group EXEC command.
https://www.cisco.com/c/en/us/td/docs/ios/12_2/configfun/command/reference/ffun_r/frf014.
html
QUESTION 23
Which command can you enter to re-enable Cisco Discovery Protocol on a local router after it has been disabled?
Correct Answer: A
Explanation
QUESTION 24
Which two commands can you use to verify an IP SLA ?(choose two)
Correct Answer: AD
Explanation
QUESTION 25
Which value can you modify to configure a specific interface as the preferred forwarding interface?
Correct Answer: B
QUESTION 26
QUESTION 27
Correct Answer: AC
Explanation
QUESTION 28
Which command can you enter on a Cisco IOS device to enable a scheduled algorithm that directs lookup calls to
multiple DNS hosts?
A. ip domain round-robin
C. ip domain lookup
D. ip domain list
Correct Answer: B
QUESTION 29
Which subnet mask will place all hosts on Network B in the same subnet with the least amount of wasted addresses?
A. 255.255.255.0
B. 255.255.254.0
C. 255.255.252.0
D. 255.255.248.0
Correct Answer: B
310 hosts We need a subnet mask of 9 bits 0 -> 1111 1111.1111 1111.1111 1110.0000 0000 -> 255.255.254.0
QUESTION 30
Which keyword in a NAT configuration enables the use of one outside IP address for multiple inside hosts?
A. source
B. static
C. pool
D. overload
Correct Answer: D
QUESTION 31
Refer to the exhibit. Which option describes how SwitchA will handle the frame just received?
A. It will flood the frame out of all the ports except Fa0/3.
Correct Answer: E
Explanation
QUESTION 32
Refer to Exhibit.
If Computer A is sending traffic to computer B, which option is the source ip address when a packet leaves R1 on
interface F0/1?
B. Ip address of computer B
D. Ip address of Computer A
Correct Answer: D
Explanation
QUESTION 33
Which subnet mask would be appropriate for a network address range to be subnetted for up to eight LANs, with each
LAN containing 5 to 26 hosts?
A. 0.0.0.240
B. 255.255.255.252
C. 255.255.255.0
D. 255.255.255.224
E. 255.255.255.240
Correct Answer: D
Explanation
For a class C network, a mask of 255.255.255.224 will allow for up to 8 networks with 32 IP addresses each (30
usable).
QUESTION 34
Which two addresses can be used to communicate with more than one device at a time? (Choose two)
A. 01-00-53-ab-11-c1
B. 10.1.1.255/22
C. 01-00-5e-7b-11-c1
D. 10.1.2.255/23
E. 172.17.210.255/24
Correct Answer: AC
QUESTION 35
Which encapsulation type is a Frame Relay encapsulation type that is supported by Cisco routers?
A. IETF
B. ANSI Annex D
C. Q9333-A Annex A
D. HDLC
Correct Answer: A
Cisco supports two Frame Relay encapsulation types: the Cisco encapsulation and the IETF Frame Relay
encapsulation, which is in conformance with RFC 1490 and RFC 2427. The former is often used to connect two Cisco
routers while the latter is used to connect a Cisco router to a non-Cisco router. You can test with your Cisco router when
typing the command Router(config-if)#encapsulation frame-relay ? on a WAN link. Below is the output of this command
(notice Cisco is the default encapsulation so it is not listed here, just press Enter to use it).
Note: Three LMI options are supported by Cisco routers are ansi, Cisco, and Q933a. They represent the ANSI Annex D,
Cisco, and ITU Q933-A (Annex A) LMI types, respectively. HDLC is a WAN protocol same as Frame-Relay and PPP so
it is not a Frame Relay encapsulation type.
QUESTION 36
Which two things does a router do when it forwards a packet? (Choose two.)
Correct Answer: AB
Explanation
QUESTION 37
C-router is to be used as a "router-on-a-stick" to route between the VLANs. All the interfaces have been properly
configured and IP routing is operational. The hosts in the VLANs have been configured with the appropriate default
gateway. What is true about this configuration?
A. These commands need to be added to the configuration: C-router(config)# router eigrp 123 C-router(config-router)#
network 172.19.0.0
B. These commands need to be added to the configuration: C-router(config)# router ospf 1 C-router(config-router)#
network 172.19.0.0 0.0.3.255 area 0
C. These commands need to be added to the configuration: C-router(config)# router rip C-router(config-router)# network
172.19.0.0
Correct Answer: D
Since all the same router (C-router) is the default gateway for all three VLANs, all traffic destined to a different VLA will
be sent to the C-router. The C-router will have knowledge of all three networks since they will appear as directly
connected in the routing table. Since the C-router already knows how to get to all three networks, no routing protocols
need to be configured.
QUESTION 38
Which command can you enter to verify that a router is synced with a configures time source?
B. ntp associations
D. ntp authenticate
Correct Answer: E
QUESTION 39
Which command allows you to set the administrative distance for EIGRP for IPv6?
A. metric weights
Correct Answer: B
QUESTION 40
Which utility can you use to determine whether a switch can send echo requests and replies?
A. SSH
B. traceroute
C. ping
D. Telnet
Correct Answer: C
Explanation
To Read the Whole Q&As, please purchase the Complete Version from Our website.
We provide exam PDF and VCE of Cisco, Microsoft, IBM, CompTIA, Oracle and other IT Certifications.
You can view Vendor list of All Certification Exams offered:
https://www.lead4pass.com/allproducts
Need Help
Please provide as much detail as possible so we can best assist you.
To update a previously submitted ticket:
Any charges made through this site will appear as Global Simulators Limited.
All trademarks are the property of their respective owners.
Copyright © lead4pass, All Rights Reserved.