Beruflich Dokumente
Kultur Dokumente
180309_Rev. 1.00
1
Contents
Thanks for purchasing KIGIS IPAS product from KYUNGWOO SYSTECH, Inc.
This product is a safety-assisting device to prevent collisions of vehicles in crossway at industrial
working sites and manufacturing facilities.
Any property or life damage caused by the breach of safety regulation and user's carelessness will not
be held responsibility. Before using this product, please read this manual carefully.
·Model No : PAS-K01-50
·FCC ID : ZE8-PAS-K01-12
·Manufacturer : KYUNGWOO SYSTECH, Inc. / KOREA
* This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions : (1) this device may
not cause harmful interference, and (2) this device must accept any interference received, including interference that may
cause undesired operation.
* CAUTION : Changes or modifications not expressly approved by the party responsible for compliance could void the user's
authority to operate the equipment.
* NOTE : This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment
is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required
to correct the interference at his own expense.
2
1. What is Crossway Zone Tag?
IPAS Crossway Zone Tag is a safety-assisting device which prevents collisions of vehicles
running in crossway at industrial working sites and manufacturing facilities.
This product is suitable to avoid collisions caused by limited visibility in warehouses or
factories.
It makes voice alert, signal light, and LED spot-light(red/blue) on the floor by detecting
vehicle tags when multiple vehicles approach the crossway simultaneously.
Vehicle Tag installed in each vehicle communicates with Crossway ZT and drivers receive a
voice alert to prevent collisions from Indicator.
High accuracy of UWB based proximity detection is an advantage of KIGIS IPAS. The
product is available without a registration or a rectification at initial installation.
Another vehicle is
approaching, watch out!
Vehicle in
intersection
Caution!
※ Failure not to observe the precautions in this manual may result in damage to the product or your property.
Use AC 110V / 220V. Do not place the
AC110V / 220V It is needed to use a product near
power plug adapter flammable materials,
when the standard stoves, candles or
voltage is different. fire. Otherwise, it
may cause fire and
product deformation.
Caution!
※ Failure to follow the warnings in this manual may result in damage to the product or serious injury.
Do not touch the Do not place heavy
connector or the objects on the
wiring with wet product or on wiring,
hands. or shock. It may
This may cause cause electric shock
electric shock or fire. or fire.
Installation Precautions
Use the product indoors Be careful not
only. It is prohibited to make a drop
to use outdoors or accident caused by
indoors with extremely poor installation.
high/low temperature Any accidents
or humidity. are irrelevant to
manufacturer.
* It is recommended to use AC power connector for protection against thunderstorm or high inflow of voltage and current.
※ Any accidents that result from not following the instructions in this manual are the user’s responsibility.
4
3. Components/Names of Parts
Components
Crossway Zone Tag(ZT) AC Power Cable Remote Control Remote Control Cable
※ It is needed to use a power (Distance Setting)
plug adapter when the
standard voltage is different.
Optional Optional
User Manual Fixture Bracket / Screw(4pcs) Eyebolt(4pcs)
※ The appearance of the product may be slightly different from the actual product received.
Names of Parts
Signal Light( ○ ▽ X )
Power Switch
Fuse Holder
AC Power Cable
Connector
LED Spot-Light(Red/Blue)
Speaker Hole
5
4. Specifications
120mm 380mm
252mm
m
120mm 0m
20
220mm
Size 380×380×282mm
Mechanical
Weight 5,500g
Feature
Mounting Method Mounting on the celling
Frequency 3993.6MHz
Bandwidth 500MHz
UWB
Feature
Measurement Distance 1 ~ 30m
※ Some features may change without prior notice to improve the performance of the product.
6
5. Installation
▶ Fixture Bracket(Optional)
▶ Eyebolt(Optional)
▶ Wire
※ In case of installation nearby an entrance, be careful not to let the product swing by wind.
7
6. Setting
Distance Setting
※ Set distance after installing and turning on the power.
Within 7m
① Connect a remote control ② Execute the setting ③ Locate the remote control
with a laptop using a USB program. nearby the crossway zone
remote control cable. tag. (within 7m)
Out of 7m range
④ ID will be automatically ⑤ Once the remote control is < Deactivated Screen >
registered in case of located out of 7m range,
successful connection. the setting screen will be
Adjust the setting and deactivated.
press SEND button.
(See the Note below)
Condition Operation
* Crossway ZT
① : " A vehicle is approaching,
watch out."
* Crossway ZT
: " Another vehicle is approching,
① watch out."
* Crossway ZT
: " Another vehicle is approching,
① ③ watch out."
Product Name
Model Name
Place of Purchase
Date of Purchase
Name of Customer
Phone Number
* Service information
1. If a performance or functional failure occurs while proper using during the
warranty period, the repair service is free of charge.
2. When the repair service is required, please present the warranty card with all
information filled in.
3. The following cases will be charged for the repair regardless of warranty period.
· Failure due to careless use or improper repair or modification
· Failure due to non-compliance to the specifications stated in this manual
4. After the expiration of warranty period, a certain fee will be charged for the
repair service.
5. The warranty card cannot be reissued.
※ If failures occur when a person who is not in our service team tries to repair the
product and breaks down, or uses components from other companies, we will
not hold the responsibility for those failures.
※ Please contact the store where you purchased the product for the refund or
exchange of the product.