Beruflich Dokumente
Kultur Dokumente
November 2006
CON-TECH SYSTEMS LTD HQ: 8150 RIVER ROAD • DELTA BC, V4G 1B5 • CANADA • PH: (604) 946-5571 • FAX: (604) 946-5548
WESTERN DIVISION: DELTA, BC, PH: (604) 946-5571, FAX: (604) 946-5548 • DESCANSO CA, USA, PH: (619) 659-9931
FAX: (619)659-9932, E-MAIL: ctswest@contechsystems.com
EASTERN DIVISION: • ELIZABETHTOWN ON • CANADA • PH: (613) 342-0041, FAX: (613) 342-0609 • RICHEY FL, USA,
PH: (866) 848 6800 • CHARLOTTE NC, USA, (704) 494-3989 • E-MAIL: ctseast@contechsystems.com
CON-TECH SYSTEMS LTD
HQ & WESTERN DIVISION (604) 946-5571
EASTERN DIVISION (613) 342-0041
Email: con-tech@contechsystems.com • Website: www.contechsystems.com
CTS
Parts-List Index
1 Technical Data 3
3 R32/20 7
6 TITAN 52/26 17
9 TITAN 130/60 23
Disclaimer:
All products are subject to change at any time without notice. Con-Tech Systems will make the best effort to keep
you informed about any changes. Please check our website (www.contechsystems.com) for updates.
All photos are for illustrative purpose only; weights are approximate.
Products must be used in conformity with safe practices and applicable codes.
For best performance results, refere to CTS/TITAN/IBO installation procedures
2
CTS
73/45 3.50 366.5 265.3 263.1 256.6 219.9 2.76 2.87 12.0
HQ & WESTERN DIVISION (604) 946-5571
103/51 8.53 778.1 618.4 616.1 544.6 466.8 3.94 4.06 29.2
R.H. THREAD 5501 3460 2750 2740 2422 2076 100 103 43.4 TITAN 127/111:
127/111* 4.65 539.7 407.0 404.8 377.8 323.8 3.94 4.06 15.8
Allowable ben-
R.H. THREAD 3000 2400 1810 1800 1680 1440 100 103 23.5
ding moment =
130/60 14.79 1785.5 1180.6 1173.8 1169.3 1071.3 4.92 5.12 50.4
R.H. THREAD 9540 7940 5250 5220 5200 4764 125 130 75.0
23.9 kNm
1 2
November 2006
Temporary Anchors ; Permanent Anchors Imperial values converted from metric values; October 2006 (737.5 lbsft)
3
CON-TECH SYSTEMS LTD
HQ & WESTERN DIVISION (604) 946-5571
EASTERN DIVISION (613) 342-0041
Email: con-tech@contechsystems.com • Website: www.contechsystems.com
November 2006
4
TITAN 30/11(left) TITAN 40/16 (left)
for weathered soft rock Button Type Button Type
and gravel hardness HV 700 hardness HV 700
hardness < 70 MPa 42 mm Ø / 46 mm Ø / 51 mm Ø / 55 mm Ø 70 mm Ø
for hard rock, Carbide Offset Cross Cut Carbide Offset Cross Cut
CTS
for hard or high quarzite rock, Button Type Button Type Button Type Button Type Button Type
reinforced concrete B25 at the carbide tipped carbide tipped carbide tipped carbide tipped carbide tipped
beginning hardness HV 1800 hardness HV1800 hardness HV 1800 hardness HV 1800 hardness HV 1800
> 70 MPa 90 mm Ø 115 mm Ø 130 mm Ø 175 mm Ø 175 mm Ø
CON-TECH SYSTEMS LTD
declarations of hardness - HRC 60 (Hardness to Rockwell C) correspond to HV 700 (Hardness to Vickers), HRC 38 correspond to HV 375
and rock hardness: - 70 MPa (soft soil and loose sand/gravel)
- 70 ÷ 150 MPa (for hard rock, like dolomit, granite, sandstone)
AV8/B1-6 - S.P.T. value (Standard Penetration Test)
Photos are illustrative only. Products must be used in conformity with safe practices and applicable codes and regulations. Subject to technical
November 2006
5
CON-TECH SYSTEMS LTD
HQ & WESTERN DIVISION (604) 946-5571
EASTERN DIVISION (613) 342-0041
Email: con-tech@contechsystems.com • Website: www.contechsystems.com
CTS/TITAN
CTS
November 2006
Photos are illustrative only. Products must be used in conformity with safe practices and applicable codes and regulations. Subject to technical
6 changes. Weights are approximate.
CON-TECH SYSTEMS LTD
HQ & WESTERN DIVISION (604) 946-5571
CTS/TITAN R32/20
Accessories
Coupling
black, part.no. R32-0124 0.43 kg pc. stock
TITAN Drill Bit - Clay bit 75 mm Ø for soft soil and loose sand/gravel,
induction hardened part.no. R32-0116 0.44 kg pc. stock
Flushing Head 32/20 available for R 32* (1 -1/4"), R 38* (1 -1/2"), T 38*, T 45*,
for left hand rotary/percussion drilling, for flushing with water, grout or air,
thread Rd 32 x 1/8" (BSP 3/4”) male for grout hose, with lubrication nipple, to be
used in connection with holder only, incl. transport box,
length 265 mm, part.no. P32-001/.002/R32-0113/P32-003 14.00 kg pc. st. T38
Holder, spring action, for Flushing Heads for R 32*, R 38*, T 38*, T 45*,
to be fixed on to the mast of the drill rig, fixing position:
hammer fully extended and spring released
part.no. T30-0370 5.90 kg pc. stock
November 2006
Photos are illustrative only. Products must be used in conformity with safe practices and applicable codes and regulations. Subject to technical
changes. Weights are approximate. 7
CON-TECH SYSTEMS LTD
HQ & WESTERN DIVISION (604) 946-5571
EASTERN DIVISION (613) 342-0041
Email: con-tech@contechsystems.com • Website: www.contechsystems.com
CTS
Page left blank intentionally
November 2006
Photos are illustrative only. Products must be used in conformity with safe practices and applicable codes and regulations. Subject to technical
8 changes. Weights are approximate.
CON-TECH SYSTEMS LTD
HQ & WESTERN DIVISION (604) 946-5571
CTS/TITAN 30/16 and 30/11 Injection Anchors are also available in other
lengths. Please ask us for pricing.
Galvanized, Metallized or EPOXY Coated CTS/TITAN Injection Anchors
and Accessories are also available. Please ask us for pricing.
Accessories
Spherical Collar Nut SW 46 x 35 mm. inclination ± 7.5
black, part.no. T30-0362 0.34 kg pc. stock
INOX Sperical Collar Nut, stainless steel,
material no. 1.4468, part.no. T30-0358 0.42 kg pc. stock
November 2006
Photos are illustrative only. Products must be used in conformity with safe practices and applicable codes and regulations. Subject to technical
changes. Weights are approximate. 9
CON-TECH SYSTEMS LTD
HQ & WESTERN DIVISION (604) 946-5571
EASTERN DIVISION (613) 342-0041
Email: con-tech@contechsystems.com • Website: www.contechsystems.com
Drill Bits
TITAN Drill Bit - Button Type 42, (42 mm Ø), hardness HRC 54,
for hand-held rotary percussion drills, for soft rock and concrete
part.no. P30-004 0.28 kg pc.
TITAN Drill Bit - Button Type 46, (46 mm Ø), hardness HRC 54,
with top and radial flushing holes, suitable for airtrack drilling machines
for harder rock and concrete
part.no. T30-0344 0.32 kg pc. stock
TITAN Drill Bit - Button Type 51, (51 mm Ø), hardness HRC 54,
with top and radial flushing holes, suitable for airtrack drilling machines
for harder rock and concrete.
part.no. P30-005 0.34 kg pc.
TITAN Drill Bit - Clay bit 75 mm Ø for soft soil and loose sand/gravel.
induction hardened part.no. T30-0348 0.44 kg pc. stock
TITAN Drill Bit - Clay bit 95 mm Ø for soft soil and loose sand/gravel.
induction hardened part.no. T30-0003 0.55 kg pc. stock
Piling Cone 75, (75 mm Ø), with backwards pointing injection hole
part.no. T30-0364 0.68 kg pc.
Accessories
Bore Hole Stopper screws on to the anchor, material PE,
to seal bore holes of 33 mm up to 56 mm Ø
part.no. T30-0365 0.10 kg pc.
Load Indicator for 30/11, to indicate loads of 70, 160 and 180 kN,
retracts by a total of 30 mm, LOBA approved
galvanized part.no. T30-0367 0.42 kg pc. stock
Expansion Shell for 30/11 and 30/16 anchors for drill hole Ø 46 up to 56 mm
part.no. T30-0368 0.77 kg pc.
Self contained Flushing Head S 22 for 30/11, for left-hand hand-held hammers
(no holder required) part.no. T30-0386 5.96 kg pc. stock
Flushing Head 30/11, for hexagon S 22 (7/8"), for left hand rotary/percussive
drilling, for flushing with water, grout or air, thread Rd 32 x 1/8" (BSP 1/2") male for
grout hose, length 323 mm, to be used in connection with holder only
incl. transport box part.no. T30-0336 5.40 kg pc.
Flushing Head 30/11 available for R 32* (1-¼"), R 38* (1 -1/2"), T 38*, T 45*,
for left hand rotary and percussive drilling, for flushing with water, grout or air, thread
Rd 32 x 1/8" (BSP 3/4") male for grout hose, with lubrication nipple, to be used in
connection with holder only, incl. transport box,
length 265 mm, part.no. T30-0339/..0380/..0340/..0379/ 14.00 kg pc. stock
Holder, spring action, for Flushing Heads for R 32*, R 38*, T 38*, T 45*,
to be fixed on to the mast of the drill rig, fixing position: hammer fully extended and
spring released
part.no. T3AC-0020 5.90 kg pc. stock
November 2006
Photos are illustrative only. Products must be used in conformity with safe practices and applicable codes and regulations. Subject to technical
changes. Weights are approximate. 11
CON-TECH SYSTEMS LTD
HQ & WESTERN DIVISION (604) 946-5571
EASTERN DIVISION (613) 342-0041
Email: con-tech@contechsystems.com • Website: www.contechsystems.com
November 2006
Photos are illustrative only. Products must be used in conformity with safe practices and applicable codes and regulations. Subject to technical
12 changes. Weights are approximate.
CON-TECH SYSTEMS LTD
HQ & WESTERN DIVISION (604) 946-5571
Accessories
November 2006
Photos are illustrative only. Products must be used in conformity with safe practices and applicable codes and regulations. Subject to technical
changes. Weights are approximate. 13
CON-TECH SYSTEMS LTD
HQ & WESTERN DIVISION (604) 946-5571
EASTERN DIVISION (613) 342-0041
Email: con-tech@contechsystems.com • Website: www.contechsystems.com
TITAN Drill Bit - HPI-Clay bit 110 mm Ø for jet grouting up to 200 bars,
with 2 nozzles, 2,3 mm Ø,
part.no. T40-0254 1.34 kg pc. stock
TITAN Drill Bit - Button Type 70, (70 mm Ø ), for soft rock and gravel,
hardness HRC 54, with top and radial flushing holes,
screw-on type.
part.no. T40-0250 0.68 kg pc. stock
TITAN Drill Bit - Carbide Cross Cut 70, (70 mm Ø), for hard rock,
screw-on type
part.no. T40-0252 0.98 kg pc. stock
TITAN Drill Bit - Cross Cut 90, (90 mm Ø), mixed soil with obstacles
part.no. T40-0256 1.05 kg pc. stock
TITAN Drill Bit - Cross Cut 115 (115 mm Ø), for soft soils, sand and cobbles and
soft rock, with top and radial flushingholes,
screw-on type
part.no. T40-0296 2 kg pc. stock
TITAN Drill Bit - Aggressive Soft Soil Bit, 100 mm Ø, for clay and mudstone,
screw-on type
part.no. T40-0253 0.83 kg pc.
TITAN Drill Bit - Carbide cross cut 3-step, cuts through several hard layers,
screw-on type
part.no. P40-004 1.2 kg pc.
Piling Cone, (90 mm Ø), for displaceable soils, clay or high water table,
screw-on type
part.no. T40-0264 2.06 kg pc.
November 2006
Photos are illustrative only. Products must be used in conformity with safe practices and applicable codes and regulations. Subject to technical
14 changes. Weights are approximate.
CON-TECH SYSTEMS LTD
HQ & WESTERN DIVISION (604) 946-5571
Accessories
Bore Hole Stopper, material PE, to seal bore holes, up to 80 mm Ø,
screw-on type, 100 mm long,
part.no. P40-010 0.1 kg pc.
Eye bolt, hole 40/30 mm, SWL 300 kN
galvanized part.no. T40-0303 1.90 kg pc.
Load Indicator for 40/16, to indicate loads of 200, 300 and 400 kN, retracts by a
total of 40 mm, LOBA approved
galvanized part.no. P40-012 0.59 kg pc.
Flushing Head 40/16 for hexagon S 22 (7/8"), for left hand rotary and percussive
drilling, for flushing with water, grout or air, thread Rd 32 x 1/8" (BSP 1/2") male for
grout hose, length 368 mm, to be used in connection with holder only, incl. transport
box,
part.no. P40-013 6.40 kg pc.
Holder, spring action, for Flushing Heads for R 32*, R 38*, T 38*, T 45*,
to be fixed on to the mast of the drill rig
fixing position: hammer fully extended and spring released
part.no. TAC-0020 5.90 kg pc. stock
Flushing Head R 55 (2-1/4"), for left hand rotary and percussive drilling, for flush-
ing with water, grout or air, thread Rd 32 x 1/8" (BSP R 3/4") male for grout hose,
with lubrication nipple, length 365 mm, to be used in connection with holder only,
incl. transport box
part.no. T40-0295 34.20 kg pc.
Holder for Flushing Head R55, C 64, RT 70, C90 and H112
for all drill rigs
part.no. TAC-0015 2.45 kg pc.
November 2006
Photos are illustrative only. Products must be used in conformity with safe practices and applicable codes and regulations. Subject to technical
changes. Weights are approximate. 15
CON-TECH SYSTEMS LTD
HQ & WESTERN DIVISION (604) 946-5571
EASTERN DIVISION (613) 342-0041
Email: con-tech@contechsystems.com • Website: www.contechsystems.com
November 2006
Photos are illustrative only. Products must be used in conformity with safe practices and applicable codes and regulations. Subject to technical
16 changes. Weights are approximate.
CON-TECH SYSTEMS LTD
HQ & WESTERN DIVISION (604) 946-5571
CTS/TITAN 52/26
Accessories
Drill Bits
TITAN Drill Bit - Cross Cut 115, (115 mm Ø), for soft soils, sand and cobbles and
soft rock with top and radial flushing holes,
screw-on type part.no. T52-0147 2.51 kg pc. stock
TITAN Drill Bit - HPI-Clay bit 130 mm Ø, for jet grouting up to 200 bar
with 2 nozzles, 2,3 mm Ø,
part.no. P52-003 2.40 kg pc. stock
TITAN Drill Bit - Button Type 115, (115 mm Ø), for hard or high quarzite rock car-
bide tipped
screw-on type
part.no. P52-004 3.3 kg pc.
November 2006
Photos are illustrative only. Products must be used in conformity with safe practices and applicable codes and regulations. Subject to technical
changes. Weights are approximate. 17
CON-TECH SYSTEMS LTD
HQ & WESTERN DIVISION (604) 946-5571
EASTERN DIVISION (613) 342-0041
Email: con-tech@contechsystems.com • Website: www.contechsystems.com
CTS/TITAN 52/26
CTS
Accessories
Holder, spring action, for Flushing Heads for R 32*, R 38*, T 38*, T 45*,
to be fixed on to the mast of the drill rig
fixing position: hammer fully extended and spring released
part.no. TAC-0020 5.90 kg pc. stock
Flushing Head R 55 ( 2- 1/4"), for rotary/percussive drilling, for flushing with water,
grout or air, thread Rd 32 x 1/8" or BSP 3/4" and 1-1/2" female for grout hose, with
lubrication nipple, length 365 mm, to be used in connection with holder only, incl.
transport box
part.no. T5R-0050 34.30 kg pc.
Holder for Flushing Head R55, C 64, RT 70, C90 and H112
for all drill rigs
part.no. TAC-0015 2.45 kg pc. stock
Grouting Connector for 52/26 , for high pressure grout-hose DN 20, thread Rd 32
x 1/8" male, with handle and lubrication nipple, galvanized
part.no. P52-005 1.80 kg pc.
November 2006
Photos are illustrative only. Products must be used in conformity with safe practices and applicable codes and regulations. Subject to technical
18 changes. Weights are approximate.
CON-TECH SYSTEMS LTD
HQ & WESTERN DIVISION (604) 946-5571
Accessories
Wedge Disc, 12° for 73/53, 200 mm, allows max. 2 x 12°,
black, part.no. T73-0162 5.97 kg pc. stock
November 2006
Photos are illustrative only. Products must be used in conformity with safe practices and applicable codes and regulations. Subject to technical
changes. Weights are approximate. 19
CON-TECH SYSTEMS LTD
HQ & WESTERN DIVISION (604) 946-5571
EASTERN DIVISION (613) 342-0041
Email: con-tech@contechsystems.com • Website: www.contechsystems.com
TITAN Drill Bit - Cross Cut, 130 mm Ø, for mixed soil with obstacles,
screw-on type
part.no. T73-0157 3.12 kg pc. stock
Flushing Head R 55 (2¼"), for right hand rotary and percussive drilling, for flush-
ing with water, grout or air, thread Rd 32 x 1/8" (BSP 3/4") male for grout hose, with
lubrication nipple, length 365 mm, to be used in connection with holder only, incl.
transport box,
part.no. T73-0149 32.10 kg pc. stock
Rotary Flushing Head R 55 (2 1/4"), self contained, length 405 mm, no holder
required, 120 mm wrench required, incl. transport box,
part.no. T73-0153 43.70 kg pc.
Flushing Head H 112, for right hand rotary and percussive drilling, for flushing with
water, grout or air, thread BSP 2" male for grout hose, with lubrication nipple, length
300 mm, to be used in connection with holder only, incl. transport box,
part.no. T73-0151 53.20 kg pc.
Holder for Flushing Head R55, C 64, RT 70, C90 and H112
for all drill rigs
part.no. TAC-0015 2.45 kg pc. stock
November 2006
Photos are illustrative only. Products must be used in conformity with safe practices and applicable codes and regulations. Subject to technical
20 changes. Weights are approximate.
CON-TECH SYSTEMS LTD
HQ & WESTERN DIVISION (604) 946-5571
CTS/TITAN 103/78 & 103/51 Injection Anchors are also available in other
lengths. Please ask us for pricing.
Galvanized, Metallized or EPOXY Coated CTS/TITAN Injection Anchors
and Accessories are also available. Please ask us for pricing.
Accessories
Drill Bits
TITAN Drill Bit - Cross Cut, 175 mm Ø, for mixed soil with obstacles,
screw-on type
part.no. T03-0108 5.70 kg pc. stock
TITAN Drill Bit - Button Type 175, (175 mm Ø), with carbide buttons,
screw-on type
part.no. T03-0119 10.2 kg pc. stock
November 2006
Photos are illustrative only. Products must be used in conformity with safe practices and applicable codes and regulations. Subject to technical
changes. Weights are approximate. 21
CON-TECH SYSTEMS LTD
HQ & WESTERN DIVISION (604) 946-5571
EASTERN DIVISION (613) 342-0041
Email: con-tech@contechsystems.com • Website: www.contechsystems.com
Flushing Head R 55 (2¼"), for right hand rotary and percussive drilling, for flush-
ing with water, grout or air, thread Rd 32 x 1/8" or BSP 3/4" and 1-1/2" female, for
grout hose, with lubrication nipple, length 365 mm, to be used in connection with
holder only, incl. transport box,
part.no. T03-0102 40.00 kg pc. stock
Flushing Head, H 112 for right hand rotary and percussive drilling , for flushing with
water, grout or air, thread BSP 2" male, for grout hose, with lubrication nipple, length
300 mm, to be used in connection with holder only, incl. transport box
part.no. T03-0104 48.40 kg pc. stock
Holder for Flushing Head R55, C 64, RT 70, C90 and H112
for all drill rigs
part.no. TAC-0015 2.45 kg pc. stock
November 2006
Photos are illustrative only. Products must be used in conformity with safe practices and applicable codes and regulations. Subject to technical
22 changes. Weights are approximate.
CON-TECH SYSTEMS LTD
HQ & WESTERN DIVISION (604) 946-5571
CTS/TITAN 130/60
Accessories
Coupling Nut
with internal rubber seal, black
black part.no. T13-0002 pc.
November 2006
Photos are illustrative only. Products must be used in conformity with safe practices and applicable codes and regulations. Subject to technical
changes. Weights are approximate. 23
CON-TECH SYSTEMS LTD
HQ & WESTERN DIVISION (604) 946-5571
EASTERN DIVISION (613) 342-0041
Email: con-tech@contechsystems.com • Website: www.contechsystems.com
CTS/TITAN
CTS
CTS/TITAN Hollow Bar Technical Data 3
Drill Bit Selection Chart 5
CTS/TITAN R32 7
Accessories 7
CTS/TITAN T30/11 & T30/16 9
Injection Hollow Bars 9
Accessories 9
CTS/TITAN T40/16 & T40/20 13
Injection Hollow Bars 13
Accessories 13
CTS/TITAN T52/26 17
Injection Hollow Bars 17
Accessories 17
CTS/TITAN T73/56 T73/53 & T73/45 19
Injection Hollow Bars 19
Accessories 19
CTS/TITAN T103/78 & T103/51 21
Injection Hollow Bars 21
Accessories 21
CTS/TITAN T130/60 23
Injection Hollow Bars 23
Accessories 23
November 2006
Photos are illustrative only. Products must be used in conformity with safe practices and applicable codes and regulations. Subject to technical
24 changes. Weights are approximate.