Beruflich Dokumente
Kultur Dokumente
Operation
Maintenance
Specifications
7:2ǘ:$<5$',225&(//8/$5
TELEPHONE INSTALLATION
Your vehicle is equipped with electronic fuel injection and other electron-
ic components. It is possible for an improperly installed/adjusted two-
way radio or cellular telephone to adversely affect electronic systems.
For this reason, we recommend that you carefully follow the radio man-
ufacturer’s instructions or consult your HYUNDAI dealer for precaution-
ary measures or special instructions if you choose to install one of these
devices.
F3
Introduction
DANGER
DANGER indicates a hazardous situation which, if not avoided, will
result in death or serious injury.
WARNING
WARNING indicates a hazardous situation which, if not avoided,
could result in death or serious injury.
CAUTION
CAUTION indicates a hazardous situation which, if not avoided,
could result in minor or moderate injury.
NOTICE
NOTICE indicates a situation which, if not avoided, could result in
vehicle damage.
F4
FOREWORD
Thank you for choosing HYUNDAI Vehicle. We are pleased to welcome you to
the growing number of discriminating people who drive HYUNDAI Vehicle. The
advanced engineering and high-quality construction of each HYUNDAI Vehicle
we build is something of which we’re very proud.
Your Owner’s Manual will introduce you to the features and operation of your
new HYUNDAI Vehicle. It is suggested that you read it carefully because the
information it contains can contribute greatly to the satisfaction you receive
from your new car.
HYUNDAI Motor India Limited also recommends that service and maintenance
on your vehicle be performed by an authorized HYUNDAI dealer.
Note : Because future owners will also need the information included in this
manual, if you sell this HYUNDAI Vehicle, please leave the manual in
the vehicle for their use. Thank you.
CAUTION
Severe engine and transaxle damage may result from the use of poor
quality fuels and lubricants that do not meet HYUNDAI Vehicle specifica-
tions. You must always use high quality fuels and lubricants that meet the
specifications listed on Page 8-5 in the Vehicle Specifications section of
the Owner’s Manual.
Copyright 2019 HYUNDAI Motor India Limited. All rights reserved. No part of
this publication may be reproduced, stored in any retrieval system or transmit-
ted in any form or by any means without the prior written permission of HYUN-
DAI Motor Company.
F5
Introduction
F6
FUEL REQUIREMENTS
2GVTQN engine Leaded (if equipped)
Unleaded For some countries, your vehicle
Your new vehicle is designed to use is designed to use leaded 0ETROL.
only unleaded fuel having an Octane When you are going to use
Rating of RON (Research Octane leaded 0ETROL, we recommend that
Number) 91 / AKI (Anti-Knock Index) you ask an authorized HYUNDAI
87 or higher. (Do not use methanol dealer whether leaded 0ETROL in
blended fuels) your vehi-cle is available or not.
Octane Rating of leaded 0ETROL is
Your new vehicle is designed to ob- same with unleaded one.
tain maximum performance with UN-
LEADED FUEL, as well as minimize 2GVTQN containing alcohol and
exhaust emissions and spark plug methanol
fouling. Gasohol, a mixture of 0ETROL and
ethanol (also known as grain
CAUTION alcohol), and 0ETROL or gasohol
containing methanol (also known as
NEVER USE LEADED FUEL. The wood alco-hol) are being marketed
use of leaded fuel is detrimental to along with or instead of leaded or
the catalytic converter and will unleaded gaso-line.
damage the engine control sys- Do not use gasohol containing more
tem’s oxygen sensor and affect than 10% ethanol, and do not use
emission control. 0ETROL or gasohol containing any
Never add any fuel system clean- methanol. Either of these fuels may
ing agents to the fuel tank other cause drivability problems and dam-
than what has been specified (We age to the fuel system, engine
recommend that you consult an control system and emission control
authorized HYUNDAI dealer for de- system and discontinue using
tails.) gasohol of any kind if drivability
problems occur.
WARNING Vehicle damage or driveability prob-
lems may not be covered by the man-
• Do not “top off” after the nozzle ufacturer’s warranty if they result from
automatically shuts off when re- the use of:
fueling. 1. Gasohol containing more than 10%
• Always check that the fuel cap is ethanol.
installed securely to prevent fuel 2. 0ETROL or gasohol containing
spillage in the event of an acci- methanol.
dent.
3. Leaded fuel or leaded gasohol.
F7
Introduction
F8
Fuel Additives Diesel engine
HYUNDAI recommends that you Diesel fuel
use unleaded 0ETROL which has an Diesel engine must be operated only
Oc-tane Rating of RON (Research on commercially available diesel fuel
Oc-tane Number) 91 / AKI (Anti- that complies with EN 590 or compa-
Knock Index) 87 or higher. rable standard. (EN stands for “Euro-
For customers who do not use good pean Norm”). Do not use marine die-
quality gasolines including fuel addi- sel fuel, heating oils, or non-approved
tives regularly, and have problems fuel additives, as this will increase
starting or the engine does not run wear and cause damage to the en-
smoothly, one bottle of additives add- gine and fuel system. The use of
ed to the fuel tank at every 10,000 km. non-approved fuels and / or fuel addi-
Additives are available from your au- tives will result in a limitation of your
thorized HYUNDAI dealer along with warranty rights.
information on how to use them. Do Diesel fuel of above cetane 51 is used
not mix other additives. in your vehicle. If two types of diesel
fuel are available, use summer or win-
ter fuel properly according to the fol-
Operation in foreign countries lowing temperature conditions.
If you are going to drive your vehicle
• Above - 5°C (23°F) ... Summer
in another country, be sure to:
type diesel fuel.
• Observe all regulations regarding
• Below -5°C (23°F) ... Winter type
registration and insurance.
diesel fuel.
• Determine that acceptable fuel is
available.
Watch the fuel level in the tank very
carefully : If the engine stops through
fuel failure, the circuits must be com-
pletely purged to permit restarting.
NOTICE
Do not let any 2GVTQN or water en-
ter the tank. This would make it
necessary to drain it out and to
bleed the lines to avoid jamming
the injection pump and damaging
the engine.
F9
Introduction
9(+,&/(%5($.ǘ,1352ǘ
NOTICE CESS
- Diesel Fuel No special break-in period is needed.
(if equipped with DPF) By following a few simple precautions
It is recommended to use the regu- for the first 1,000 km (600 miles) you
lated automotive diesel fuel for may add to the performance, econo-
diesel vehicle equipped with the my and life of your vehicle:
DPF system. • Do not race the engine.
If you use diesel fuel including • While driving, keep your engine
high sulfur (more than 50 ppm sul- speed (rpm, or revolutions per min-
fur) and unspecified additives, it ute) between 2,000 rpm and 4,000
can cause the DPF system to be rpm.
damaged and white smoke can be • Do not maintain a single speed for
emitted. long periods of time, either fast or
slow.
Biodiesel Varying engine speed is needed to
Commercially supplied Diesel blends properly break-in the engine.
of no more than 7% biodiesel, com- • Avoid hard stops, except in emer-
monly known as “B7 Diesel” may be gencies, to allow the brakes to seat
used in your vehicle if Biodiesel properly.
meets EN 14214 or equivalent speci- • Don’t tow a trailer during the first
fications. (EN stands for “European 2,000 km (1,200 miles) of opera-
Norm”). The use of biofuels exceed- tion.
ing 7% made from rapeseed methyl
ester (RME), fatty acid methyl ester
(FAME), vegetable oil methyl ester
(VME) etc. or mixing diesel exceed-
ing 7% with biodiesel will cause in-
creased wear or damage to the en-
gine and fuel system. Repair or
replacement of worn or damaged
components due to the use of non
approved fuels will not be covered by
the manufactures warranty.
NOTICE
• Never use any fuel, whether die-
sel, B7 biodiesel or otherwise,
that fails to meet the latest pe-
troleum industry specification.
• Never use any fuel additives or
treatments that are not recom-
mended or approved by the ve-
hicle manufacturer.
F10
Table of contents
Index I
1. Maintenance Record Sheet
1
1-2
Repair category - Free Ser./Paid Serv./Running Repair/AC Repair
1-3
01
2. Hyundai Warranty Policy
2-3
Hyundai Warranty Policy
2-8
02
2-9
3. Your vehicle at a glance
(;7(5,2529(59,(:ǣ,Ǥ
ٻFront view
OQXI019001
1. Hood .....................................................................................................................5-26
2. Headlight/Daytime running light* ..........................................................................9-74
3. Turn signal light ....................................................................................................9-76
4. Fog light* ..............................................................................................................9-77
5. Tires and wheels .........................................................................................9-44, 10-4
6. Outside rearview mirror ........................................................................................5-38
7. Front windshield wiper blades ..............................................................................5-85
8. Windows ...............................................................................................................5-21
* : if equipped
3-2
03
(;7(5,2529(59,(:ǣ,,Ǥ
ٻRear view
OQXI019002
1. Antenna ..................................................................................................................6-2
2. Doors ....................................................................................................................5-13
(WGNſNNGTFQQT ......................................................................................................5-32
4. Parking Distance Warning (Reverse) System......................................................5-90
5. High mounted stop light .......................................................................................9-80
6. Rear view monitor* ...............................................................................................5-88
7. Rear window wiper blade*....................................................................................9-39
8. Tailgate.................................................................................................................5-19
9. Rear lamps ...........................................................................................................9-78
* : if equipped
3-3
Your vehicle at a glance
INTERIOR OVERVIEW
3-4
03
13. Steering wheel....................................................................................................5-35
14. Clutch pedal....................................................................................................... 7-31
15. Brake pedal.........................................................................................................7-32
16. Accelerator pedal................................................................................................ 7
17. Hood release lever .............................................................................................5-26
18. Engine Start/Stop button ......................................................................................7-9
Key ignition switch................................................................................................7-5
* : if equipped
3-5
Your vehicle at a glance
ٻType A ٻType B
3-6
03
12. Infotainment system* ............................................................................................6-2
13. Hazard switch .......................................................................................................8-2
14. Passenger's front air bag ...................................................................................4-42
15. Glove box .........................................................................................................5-116
* KHGSWKRRGF
3-7
Your vehicle at a glance
ENGINE COMPARTMENT
ٻ0ETROL Engine (1.2 MPI)
The actual engine room in the vehicle may differ from the illustration.
OQXI079001/OQXI079100
3-8
03
ٻDiesel Engine (1.4 WGT)
The actual engine room in the vehicle may differ from the illustration.
OQXI079002
3-9
4. Safety system of your
vehicle
Seats ....................................................................................................................4-2
Front seats .......................................................................................................4-5
Rear seats........................................................................................................ 4-9
Seat belts ........................................................................................................... 4-14
Pre-tensioner seat belt.................................................................................. 4-19
Additional seat belt safety precautions ....................................................... 4-21
Care of seat belts ...........................................................................................4-23 4
Child restraint system .......................................................................................4-24
Using a child restraint system ......................................................................4-26
Installing a Child Restraint System (CRS) .................................................... 4-27
Air bag - supplemental restraint system (SRS) ...............................................4-34
How does the air bag system operate ........................................................4-35
Do not install a child restraint on the front passenger’s seat..................... 4-37
Air bag warning and indicator ......................................................................4-38
SRS components and functions ...................................................................4-39
Driver’s and passenger’s front air bag ........................................................ 4-42
Side impact air bag ...................................................................................... 4-44
Curtain air bag .............................................................................................. 4-46
SRS Care.........................................................................................................4-52
Air bag warning label ................................................................................... 4-54
Safety system of your vehicle
SEATS
The actual feature in the vehicle may differ from the illustration.
OQXI039001
4-2
04
WARNING WARNING
Loose objects Do not use a sitting cushion that
Loose objects in the driver’s foot reduces friction between the seat
area could interfere with the opera- and passenger. The passenger’s
tion of the foot pedals, possibly hips may slide under the lap por-
causing an accident. Do not place tion of the seat belt during an acci-
anything under the front seats. dent or a sudden stop. Serious or
fatal internal injuries could result
because the seat belt can’t operate
WARNING normally.
Uprighting seat
When you return the seatback to WARNING
its upright position, hold the seat- Driver’s seat
back and return it slowly and be
sure there are no other occupants • Never attempt to adjust seat
around the seat. If the seatback is while the vehicle is moving. This
returned without being held and could result in loss of control,
controlled, the back of the seat and an accident causing death,
could move forward or backward serious injury, or property dam-
resulting in accidental injury to a age.
person struck by the seatback. • Do not allow anything to inter-
fere with the normal position of
the seatback. Storing items
WARNING against a seatback or in any oth-
Driver responsibility for passen- er way interfering with proper
gers locking of a seatback could re-
sult in serious or fatal injury in a
Riding in a vehicle with seatback sudden stop or collision.
reclined could lead to serious or fa-
tal injury in an accident. If a seat is • Always drive and ride with your
reclined during an accident, the oc- seatback upright and the lap
cupant’s hips may slide under the portion of the seat belt snug and
lap portion of the seat belt applying low across the hips. This is the
great force to the unprotected ab- best position to protect you in
domen. The protection of your re- case of an accident.
straint system (seat belt and air • In order to avoid unnecessary
bags) is great ly reduced by reclin- and perhaps severe air bag inju-
ing your seat. Serious or fatal inter- ries, always sit as far back as
nal injuries could result. The driver possible from the steering wheel
must advise the passenger to keep while maintaining comfortable
the seatback in an upright position control of the vehicle.
whenever the vehicle is in motion.
4-3
Safety system of your vehicle
WARNING WARNING
Rear seatbacks After adjusting the seat, always
• The rear seatback must be se- check that it is securely locked
curely latched. If not, passen- into place by attempting to move
gers and objects could be the seat forward or backward with-
thrown forward resulting in seri- out using the lock release lever.
ous injury or death in the event Sudden or unexpected movement
of a sudden stop or collision. of the driver’s seat could cause
you to lose control of the vehicle
• Luggage and other cargo should resulting in an accident.
be laid flat in the cargo area. If
objects are large, heavy, or must
be piled, they must be secured. WARNING
Under no circumstances should
cargo be piled higher than the • Do not adjust the seat while
seatbacks. Failure to follow wearing seat belts. Moving the
these warnings could result in seat cushion forward may cause
serious injury or death in the strong pressure on the abdo-
event of a sudden stop, collision men.
or rollover. • Use extreme caution so that
• No passenger should ride in the hands or other objects are not
cargo area or sit or lie on folded caught in the seat mechanisms
seatbacks while the vehicle is while the seat is moving.
moving. All passengers must be • Do not put a cigarette lighter on
properly seated in seats and re- the floor or seat. When you op-
strained properly while riding. erate the seat, gas may gush out
• When resetting the seatback to of the lighter and cause fire.
the upright position, make sure • If there are occupants in the rear
it is securely latched by pushing seats, be careful while adjusting
it forward and backwards. the front seat position.
• To avoid the possibility of burns,
do not remove the carpet in the
cargo area. Emission control de-
vices beneath this floor gener-
ate high temperatures.
4-4
04
Front seats
OQXI039003
OQXI039004
4-5
Safety system of your vehicle
Headrest •
OLF034072N
4-6
04
OLF034015 OQXI039005
OQXI039006
Removal/Reinstall
To remove the headrest:
1. Recline the seatback (2) with the
recline lever (1).
2. Raise headrest as far as it can go.
3. Press the headrest release button
(3) while pulling the headrest up
(4).
WARNING
NEVER allow anyone to ride in a
seat with the headrest removed.
4-7
Safety system of your vehicle
Seatback pocket
OQXI039007
4-8
04
Rear seats •
Headrest
OLF034072N
4-9
Safety system of your vehicle
WARNING
• Never allow passengers to sit on
OQXI039010 top of the folded down seatback
while the vehicle is moving as
Adjusting the height up and down this is not a proper seating posi-
(if equipped) tion and no seat belts are avail-
To raise the headrest, pull it up (1). able for use. This could result in
To lower the headrest, push and hold serious injury or death in case
the release button (2) on the headrest of an accident or sudden stop.
support and lower the headrest (3). • Objects carried on the folded
down seatback should not ex-
tend higher than the top of the
front seats. This could allow car-
go to slide forward and cause
injury or damage during sudden
stops.
OQXI039011
WARNING
Make sure the headrest locks in
position after adjusting it to prop-
erly protect the occupants.
4-10
04
Type A
1. Set the front seatback to the up-
right position and if necessary,
slide the front seat forward.
2. Lower the rear headrests to the
lowest position (if equipped with
adjustable headrests).
OQXI039013
OQXI039012
4-11
Safety system of your vehicle
Type B
1. Set the front seatback to the up-
right position and if necessary,
slide the front seat forward.
2. Lower the rear headrests to the
lowest position (if equipped with
adjustable headrests).
OQXI039013
OQXI039015
i Information
If you are not able to pull out the seat
belt from the retractor, firmly pull the
belt out and release it. Then you will be
able to pull the belt out smoothly.
4-12
04
WARNING WARNING
When you return the rear seatback Cargo loading
to its upright position after being Make sure the engine is off, the
folded down: dual clutch transmission is in P
Be careful not to damage the seat (Park) or the Manual transmission
belt webbing or buckle. Do not al- is in R (Reverse) or 1st, and the
low the seat belt webbing or buck- parking brake is securely applied
le to get caught or pinched in the whenever loading or unloading
rear seat. Ensure that the seatback cargo. Failure to take these steps
is completely locked into its up- may allow the vehicle to move if
right position by pushing on the the shift lever is inadvertently
top of the seatback. Otherwise, in moved to another position.
an accident or sudden stop, the
seat could fold down and allow
cargo to enter the passenger com- Armrest (if equipped)
partment, which could result in se-
rious injury or death.
NOTICE
• When returning the rear seat-
backs to the upright position,
remember to return the rear
shoulder belts to their proper
position.
OQXI039016
• Routing the seat belt webbing
through the rear seat belt guides The armrest is located in the center of
will help keep the seat belts from the rear seat. Pull the armrest down
being trapped behind or under from the seatback to use it.
the seats.
WARNING
Cargo
Cargo should always be secured
to prevent it from being thrown
about the vehicle in a collision and
causing injury to the vehicle occu-
pants. Do not place objects in the
rear seats, since they cannot be
properly secured and may hit the
front seat occupants in a collision.
4-13
Safety system of your vehicle
SEAT BELTS
WARNING WARNING
• For maximum restraint system • Seat belts are designed to bear
protection, the seat belts must upon the bony structure of the
always be used whenever the body, and should be worn low
car is moving. across the front of the pelvis or
• Seat belts are most effective the pelvis, chest and shoulders,
when seatbacks are in the up- as applicable; wearing the lap
right position. section of the belt across the ab-
dominal area must be avoided.
• Children age 12 and under must
always be properly restrained in • Seat belts should be adjusted as
the rear seat. Never allow chil- firmly as possible, consistent
dren to ride in the front passen- with comfort, to provide the pro-
ger seat. If a child over 12 must tection for which they have been
be seated in the front seat, he/ designed.
she must be properly belted and • A slack belt will greatly reduce
the seat should be moved as far the protection afforded to the
back as possible. wearer.
• Never wear the shoulder belt un- • Care should be taken to avoid
der your arm or behind your contamination of the webbing
back. An improperly positioned with polishes, oils and chemi-
shoulder belt can cause serious cals, and particularly battery
injuries in a crash. The shoulder acid. Cleaning may safely be
belt should be positioned mid- carried out using mild soap and
way over your shoulder across water. The belt should be re-
your collarbone. placed if webbing becomes
• Never wear a seat belt over frag- frayed, contaminated or dam-
ile objects. If there is a sudden aged.
stop or impact, the seat belt can • It is essential to replace the en-
damage it. tire assembly after it has been
• Avoid wearing twisted seat belts. worn in a severe impact even if
A twisted belt can’t do its job as damage to the assembly is not
well. In a collision, it could even obvious. Belts should not be
cut into you. Be sure the belt worn with straps twisted. Each
webbing is straight and not belt assembly must only be used
twisted. by one occupant; it is dangerous
to put a belt around a child being
• Be careful not to damage the carried on the occupant’s lap.
belt webbing or hardware. If the
belt webbing or hardware is
damaged, replace it.
4-14
04
WARNING Seat belt warning (if equipped)
• No modifications or additions
should be made by the user
which will either prevent the
seat belt adjusting devices from
operating to remove slack, or
prevent the seat belt assembly
from being adjusted to remove
slack.
• When you fasten the seat belt,
be careful not to latch the seat 1GQA2083
belt in buckles of other seat. It’s
As a reminder to the driver the driv-
very dangerous and you may
er’s seat belt warning lights will illumi-
not be protected by the seat belt
nate for approximately 6 seconds
properly.
each time you turn the ignition switch
• Do not unfasten the seat belt ON regardless of belt fastening.
and do not fasten and unfasten
If the driver’s seat belt is not fastened
the seat belt repeatedly while
when the ignition switch is turned ON
driving. This could result in loss
or if it is disconnected after the igni-
of control, and an accident caus-
tion switch is turned ON, the seat belt
ing death, serious injury, or
warning light will illuminate until the
property damage.
belt is fastened.
• When fastening the seat belt,
If you continue not to fasten the seat
make sure that the seat belt
belt and you drive over 9 km/h, the il-
does not pass over objects that
luminated warning light will start to
are hard or can break easily.
blink until you drive under 6 km/h.
• Make sure there is nothing in the
If you continue not to fasten the seat
buckle. The seat belt may not be
belt and you drive over 20 km/h (12
fastened securely.
mph) the seat belt warning chime will
sound for approximately 100 seconds
and the corresponding warning light
will blink.
4-15
Safety system of your vehicle
Lap/shoulder belt
OHSS038100
i Information
If you are not able to pull out the safety
belt from the retractor, firmly pull the
belt out and release it. After release,
you will be able to pull the belt out
smoothly.
4-16
04
WARNING
Improperly positioned seat belts
may increase the risk of serious in-
jury in an accident.Take the follow-
ing precautions when adjusting
the seat belt:
• Position the lap portion of the
seat belt as low as possible
across your hips, not on your
OHSS038103
waist, so that it fits snugly.This
allows your strong pelvic bones To release the seat belt:
to absorb the force of the crash, The seat belt is released by pressing
reducing the chance of internal the release button (1) in the locking
injuries. buckle. When it is released, the belt
• Position one arm under the should automatically draw back into
shoulder belt and the other over the retractor.
the belt, as shown in the illustra- If this does not happen, check the
tion. belt to be sure it is not twisted, then
• Always position the shoulder try again.
belt anchor into the locked posi-
tion at the appropriate height.
• Never position the shoulder belt
across your neck or face.
4-17
Safety system of your vehicle
Lap belt
OQXI039017
OLMB033089
When using the rear center seat belt,
To fasten your seat belt: the buckle with the “ENTER” mark
To fasten a 2-point static type belt, in- must be used.
sert the metal tab into the locking
buckle. There will be an audible “click”
when the tab locks into the buckle.
Check to make sure the belt is prop-
erly locked and that the belt is not
twisted.
OLMB033036
4-18
04
Pre-tensioner seat belt WARNING
(if equipped)
• Always wear your seat belt and
sit properly in your seat.
• Do not use the seat belt if it is
loose or twisted. A loose or
twisted seat belt will not protect
you properly in an accident.
• Do not place anything near the
buckle. This may adversely af-
fect the buckle and cause it to
function improperly.
OIB034039
• Always replace your pre-ten-
Your vehicle is equipped with driver’s sioners after activation or an ac-
and front passenger’s pre-tensioner cident.
seat belts (retractor pre-tensioner).
The purpose of the pre-tensioner is to • NEVER inspect, service, repair
make sure the seat belts fit tightly or replace the pre-tensioners
against the occupant’s body in cer- yourself.This must be done by
tain frontal or side collision(s). The an authorized HYUNDAI dealer.
pre-tensioner seat belts may be acti- Do not hit the seat belt assem-
vated in crashes where the frontal or blies.
side collision(s) is severe enough, to-
gether with the air bags.When the ve- WARNING
hicle stops suddenly, or if the occu-
pant tries to lean forward too quickly, Do not touch the pre-tensioner seat
the seat belt retractor will lock into belt assemblies for several minutes
position. In certain frontal collisions, after they have been activated.
the pre-tensioner will activate and When the pre-tensioner seat belt
pull the seat belt into tighter contact mechanism deploys during a colli-
against the occupant’s body. sion, the pre-tensioner can become
hot and can burn you.
WARNING
CAUTION
For your safety, be sure that the belt
webbing is not loose or twisted and Body work on the front area of the
always sit properly on your seat. vehicle may damage the pre-ten-
sioner seat belt system. Therefore,
we recommend the system to be
When the vehicle stops suddenly, or
serviced by an authorized HYUND-
if the occupant tries to lean forward
AI dealer.
too quickly, the seat belt retractor will
lock into position. In certain frontal
collisions, the pre-tensioner will acti-
vate and pull the seat belt into tighter
contact against the occupant’s body.
4-19
Safety system of your vehicle
i Information
• Both the driver’s and front passen-
ger’s pre-tensioner seat belts may be
activated in certain frontal or side
collisions.
• When the pre-tensioner seat belts
are activated, a loud noise may be
heard and fine dust, which may ap-
pear to be smoke, may be visible in
8KMB3311/H
the passenger compartment. These
The seat belt pre-tensioner system are normal operating conditions
consists mainly of the following com- and are not hazardous.
ponents. Their locations are shown in • Although it is non-toxic, the fine
the illustration: dust may cause skin irritation and
(1) SRS air bag warning light should not be inhaled for prolonged
(2) Retractor pre-tensioner assembly periods. Wash all exposed skin areas
thoroughly after an accident in
(3) SRS control module which the pre-tensioner seat belts
were activated.
NOTICE
The sensor that activates the SRS
control module is connected with
the pre–tensioner seat belts. The
SRS air bag warning light on the
instrument cluster will illuminate
for approximately 6 seconds after
the ignition switch is placed in the
ON position, and then it should
turn off. If the pre-tensioner is not
working properly, the warning light
will illuminate even if the SRS air
bag is not malfunctioning. If the
warning light does not illumi-
nate,stays illuminated or illumi-
nates when the vehicle is being
driven, we recommend the pre-ten-
sioner seat belts and/or SRS con-
trol module be inspected by an au-
thorized HYUNDAI dealer as soon
as possible.
4-20
04
Additional seat belt safety pre- Seat belt use and children
cautions Infant and small children
Seat belt use during pregnancy Most countries have Child Restraint
The seat belt should always be used System laws which require children
during pregnancy. The best way to to travel in approved Child Restraint
protect your unborn child is to protect System devices, including booster
yourself by always wearing the seat seats.The age at which seat belts can
belt. Pregnant women should always be used instead of Child Restraint
wear a lap-shoulder seat belt. Place System differs among countries, so
the shoulder belt across your chest, you should be aware of the specific
routed between your breasts and requirements in your country, and
away from your neck. Place the lap where you are travelling. Infant and
belt below your belly so that it fits Child Restraint System must be prop-
SNUGLY across your hips and pelvic erly placed and installed in a rear
bone, under the rounded part of the seat. For more details refer to the
belly. “Child Restraint Systems”in this
chapter.
WARNING
WARNING
To reduce the risk of serious injury
or death to an unborn child during ALWAYS properly restrain infants
an accident, pregnant women and small children in a Child Re-
should NEVER place the lap portion straint System appropriate for the
of the seat belt above or over the child’s height and weight. To reduce
area of the abdomen where the un- the risk of serious injury or death to
born child is located. a child and other passengers,NEV-
ER hold a child in your lap or arms
when the vehicle is moving.The vio-
lent forces created during an acci-
dent will tear the child from your
arms and throw the child against the
interior of the vehicle.
4-21
Safety system of your vehicle
WARNING
• Always make sure larger chil-
dren’s seat belts are worn and
properly adjusted.
• NEVER allow the shoulder belt
to contact the child’s neck or
face.
• Do not allow more than one
child to use a single seat belt.
4-22
04
Seat belt use and injured people Care of seat belts
A seat belt should be used when an Seat belt systems should never be
injured person is being transported. disassembled or modified. In addi-
Consult a physician for specific rec- tion, care should be taken to assure
ommendations. that seat belts and belt hardware are
not damaged by seat hinges, doors
or other abuse.
One person per belt
Two people (including children)
should never attempt to use a single Periodic inspection
seat belt. This could increase the se- All seat belts should be inspected pe-
verity of injuries in case of an acci- riodically for wear or damage of any
dent. kind. Any damaged parts should be
replaced as soon as possible.
Do not lie down
Sitting in a reclined position when the Keep belts clean and dry
vehicle is in motion can be danger- Seat belts should be kept clean and
ous. Even when buckled up, the pro- dry. If belts become dirty, they can be
tections of your restraint system (seat cleaned by using a mild soap solution
belts and/or air bags) is greatly re- and warm water. Bleach, dye, strong
duced by reclining your seatback. detergents or abrasives should not
Seat belts must be snug against your be used because they may damage
hips and chest to work properly. and weaken the fabric.
During an accident, you could be
thrown into the seat belt, causing
neck or other injuries. When to replace seat belts
The more the seat back is reclined, The entire seat belt assembly or as-
the greater the chance for the pas- semblies should be replaced if the
senger’s hips to slide under the lap vehicle has been involved in an acci-
belt or the passenger’s neck to strike dent. This should be done even if no
the shoulder belt. damage is visible.We recommend
that you consult an authorized HYUN-
DAI dealer.
WARNING
• NEVER ride with a reclined seat-
back when the vehicle is mov-
ing.
• Riding with a reclined seatback
increases your chance of seri-
ous or fatal injuries in the event
of a collision or sudden stop.
• Driver and passengers should
always sit well back in their
seats,properly belted,and with
the seatbacks upright.
4-23
Safety system of your vehicle
4-24
04
WARNING • Children often squirm and repo-
sition themselves improperly.
To reduce the chance of serious Never let a child ride with the
or fatal injuries: shoulder belt under their arm or
• Children of all ages are safer behind their back. Always prop-
when restrained in the rear seat. erly position and secure chil-
A child riding in the front pas- dren in rear seat.
senger seat can be forcefully • Never allow a child to stand-up
struck by an inflating air bag re- or kneel on the seat or floor-
sulting in serious or fatal inju- board of a moving vehicle.
ries. During a collision or sudden
• Always follow the instructions stop, the child can be violently
for installation and use of the thrown against the vehicles inte-
child restraint maker. rior, resulting in serious injury.
• Always make sure the child seat • Never use an infant carrier or a
is secured properly in the car child safety seat that “hooks”
and your child is securely re- over a seatback, it may not pro-
strained in the child seat. vide adequate security in an ac-
cident.
• Never hold a child in your arms
or lap when riding in a vehicle. • Seat belts can become very hot,
The violent forces created especially when the car is
during a crash will tear the child parked in direct sunlight. Al-
from your arms and throw the ways check seat belt buckles
child against the car’s interior. before fastening them over a
child.
• Never put a seat belt over your-
self and a child. During a crash, • After an accident, we recom-
the belt could press deep into mend that the system be
the child causing serious inter- checked by an authorized
nal injuries. HYUNDAI dealer.
• Never leave children unattended • If there is not enough space to
in a vehicle - not even for a short place the child restraint system
time. The car can heat up very because of the driver’s seat, in-
quickly, resulting in serious in- stall the child restraint system in
juries to children inside. Even the rear right seat.
very young children may inad-
vertently cause the vehicle to
move, entangle themselves in
the windows, or lock themselves
or others inside the vehicle.
• Never allow two children, or any
two persons, to use the same
seat belt.
4-25
Safety system of your vehicle
WARNING
Never place a rear-facing child re-
straint in the front passenger seat,
because of the danger that an in-
flating passenger-side air bag
could impact the rear-facing child
restraint and kill the child.
4-26
04
Installing a Child Restraint After selecting a proper Child Re-
System (CRS) straint System and checking that the
Child Restraint System fits properly in
the rear of this vehicle, you are ready
WARNING to install the Child Restraint System
according to the manufacturer’s in-
Before installing your Child Re-
struction. There are three general
straint System always:
steps in installing the Child Restraint
• Read and follow the instructions System properly:
provided by the manufacturer of
• Properly secure the Child Re-
the Child Restraint System.
straint System to the vehicle. All
• Failure to follow all warnings Child Restraint Systems must be
and instructions could increase secured to the vehicle with the lap
the risk of the SERIOUS INJURY belt or lap part of a lap/shoulder
or DEATH if an accident occurs. belt or with the top-tether and/or
ISOFIX anchorage.
WARNING • Make sure the Child Restraint
System is firmly secured. After
If the vehicle headrest prevents installing a Child Restraint System
proper installation of a Child Re- to the vehicle, push and pull the
straint System (as described in the Child Restraint System forward
Child Restraint System manual), and from side-to-side to verify that
the headrest of the respective it is securely attached to the vehi-
seating position shall be readjust- cle seat. A Child Restraint System
ed or entirely removed. secured with a seat belt should be
installed as firmly as possible.
However, some side-to- side
movement can be expected.
When installing a Child Restraint
System, adjust the vehicle seat (up
and down, forward and rearward)
so that your child fits in the Child
Restraint System in a comfortable
manner.
4-27
Safety system of your vehicle
• Secure the child in the Child Re- ISOFIX anchorage and top-tether
straint System. Make sure the anchorage (ISOFIX system) for
child is properly strapped in the children (if equipped)
Child Restraint System according The ISOFIX system holds a Child Re-
to the Child Restraint System man- straint System during driving and in
ufacturer’s instructions. an accident. This system is designed
to make installation of the Child Re-
straint System easier and reduce the
WARNING possibility of improperly installing
A Child Restraint System in a your Child Restraint System. The
closed vehicle can become very ISOFIX system uses anchors in the
hot. To prevent burns, check the vehicle and attachments on the Child
seating surface and buckles be- Restraint System. The ISOFIX sys-
fore placing your child in the Child tem eliminates the need to use seat
Restraint System. belts to secure the Child Restraint
System to the rear seats.
ISOFIX anchors are metal bars built
into the vehicle. There are two lower
anchors for each ISOFIX seating po-
sition that will accommodate a Child
Restraint System with lower attach-
ments.
To use the ISOFIX system in your ve-
hicle, you must have a Child Restraint
System with ISOFIX attachments.
(An ISOFIX-Child Restraint System
may only be installed if it has vehi-
cle-specific or universal approval in
accordance with the requirements of
ECE-R 44 or ECE-R 129.)
The Child Restraint System manufac-
turer will provide you with instructions
on how to use the Child Restraint
System with its attachments for the
lower anchorages.
4-28
04
OLM039035 OQXI039018
ISOFIX anchorages have been pro- The ISOFIX anchorages symbols are
vided in the left and right outboard located on the left and right rear seat
rear seating positions. Their locations cushions to identify the position of the
are shown in the illustration. There ISOFIX anchorages in your vehicle
are no ISOFIX anchorages provided (see arrows in illustration).
for the center rear seating position.
WARNING
Do not attempt to install a Child
Restraint System using ISOFIX an-
chorages in the rear center seating
position. There are no ISOFIX an-
chorages provided for this seat.
Using the outboard seat anchorag-
es, for the CRS installation on the
OQXI039019
rear center seating position, can
damage the anchorages which Both rear outboard seats are
may break or fail in a collision re- equipped with a pair of ISOFIX an-
sulting in serious injury or death. chorages as well as a corresponding
top-tether anchorage on the back
side of the rear seats.
(Child Restraint Systems with univer-
sal approval according to ECE-R44
or ECE-R129 need to be fixed addi-
tionally with a top-tether connected to
the corresponding top-tether anchor-
age point on the back side of the rear
seats.)
ISOFIX anchorages are located be-
tween the seatback and the seat
cushion of the rear seat left and right
outboard seating positions.
4-29
Safety system of your vehicle
4-30
04
Securing a Child Restraint Sys- WARNING
tem with “Top-tether anchorage”
system (if equipped) Take the following precautions
when installing the top-tether:
• Read and follow all installation
instructions provided with your
Child Restraint System.
• NEVER attach more than one
Child Restraint System to a sin-
gle top-tether anchorage. This
could cause the anchorage or
attachment to come loose or
break.
OQXI039020
• Do not attach the top-tether to
First secure the Child Restraint Sys- anything other than the correct
tem with the ISOFIX anchorages or top-tether anchorage. It may not
the seat belt. If the Child Restraint work properly if attached to
System manufacturer recommends something else.
the top-tether to be attached, attach
and tighten the top-tether to the • Child Restraint System anchor-
top-tether anchorage. Top-tether an- ages are designed to withstand
chorages are located on the back of only those loads imposed by
the rear seats. correctly fitted Child Restraint
Systems. Under no circum-
stances are they to be used for
adult seat belts or harnesses or
for attaching other items or
equipment to the vehicle.
4-31
Safety system of your vehicle
MMSA3030
Child Seat Restraint Suitability for Seat Position using the Seat Belt
Use child safety seats that have been officially approved and are appropriate
for your children. When using the child safety seats, refer to the following table.
Seating position
0 : Up to 10 kg X U U X
0+ : Up to 13 kg X U U X
I : 15 kg to 25 kg X U U UF
II : 9 kg to 18 kg X U U UF
III : 22 kg to 36 kg X U U UF
U : Suitable for “universal” category restraints approved for use in this mass
group.
UF : Universal Front Facing
4-33
Safety system of your vehicle
$,5%$*ǘ6833/(0(17$/5(675$,176<67(0ǣ656Ǥ
The actual air bags in the vehicle may differ from the illustration.
OIB037032R
* : if equipped
4-34
04
WARNING How does the air bag system
operate
• Even in vehicles with air bags, • Air bags are activated (able to in-
you and your passengers must flate if necessary) only when the
always wear the safety belts ignition switch is placed to the ON
provided in order to minimize or START position.
the risk and severity of injury in
• Air bags inflate instantly in the
the event of a collision or roll-
event of serious frontal or side col-
over.
lision in order to help protect the
• SRS and pretensioners contain occupants from serious physical
explosive chemicals. injury.
If scraping a vehicle without re- • There is no single speed at which
moving SRS and pretensioners the air bags will inflate.
from a vehicle, it may cause fire.
Generally, air bags are designed to
Before scraping a vehicle, we
inflate based upon the severity of a
recommend that you contact an
collision and its direction. These
authorized Hyundai dealer.
two factors determine whether the
• Keep the SRS parts and wirings sensors produce an electronic de-
away from water or any liquid. If ployment/ inflation signal.
the SRS components are inoper-
• Air bag deployment depends on a
ative due to exposure to water
number of factors including vehicle
or liquids, it may cause fire or
speed, angles of impact and the
severe injury.
density and stiffness of the vehi-
cles or objects which your vehicle
hits in the collision. The determin-
ing, factors are not limited to those
mentioned above.
• The front air bags will completely
inflate and deflate in an instant.
It is virtually impossible for you to
see the air bags inflate during an
accident.
It is much more likely that you will
simply see the deflated air bags
hanging out of their storage com-
partments after the collision.
4-35
Safety system of your vehicle
4-36
04
Noise and smoke Do not install a child restraint
When the air bags inflate, they make on the front passenger’s seat.
a loud noise and they leave smoke (if equipped)
and powder in the air inside of the ve-
hicle. This is normal and is a result of
the ignition of the air bag inflator. Af-
ter the air bag inflates, you may feel
substantial discomfort in breathing
due to the contact of your chest with
both the seat belt and the air bag, as
well as from breathing the smoke and
powder. Open your doors and/or
windows as soon as possible after
impact in order to reduce discom- OYDESA2042
fort and prevent prolonged expo- Never place a rear-facing child re-
sure to the smoke and powder. straint in the front passenger’s seat. If
Though smoke and powder are the air bag deploys, it would impact
non-toxic, it may cause irritation to the rear-facing child restraint, caus-
the skin (eyes, nose and throat, etc.). ing serious or fatal injury.
If this is the case, wash and rinse with In addition, do not place front-facing
cold water immediately and consult child restraints in the front passen-
with the doctor if the symptom per- ger’s seat either. If the front passen-
sists. ger air bag inflates, it would cause
serious or fatal injuries to the child.
WARNING
When the air bags deploy, the air
bag related parts in the steering
wheel and/or instrument panel
and/or in both sides of the roof
rails above the front and rear doors
are very hot. To prevent injury, do
not touch the air bag storage areas
internal components immediately
after an air bag has inflated.
4-37
Safety system of your vehicle
4-38
04
SRS components and func- WARNING
tions
If any of the following conditions
occurs, this indicates a malfunc-
tion of the SRS. We recommend
that the system be inspected by an
authorized HYUNDAI dealer.
• The light does not turn on briefly
when you turn the ignition ON.
• The light stays on after illumi-
nating for approximately 6 sec-
onds.
OQXI039038
• The light comes on while the ve-
The SRS consists of the following hicle is in motion.
components:
• The light blinks when the igni-
(1) Driver’s front air bag module tion switch is in ON position.
(2) Passenger’s front air bag module
(3) Pre-tensioner seatbelt system*
(4) Air bag warning light
(5) SRS control module (SRSCM)
(6) Front impact sensor
(7) Side impact air bag modules*
(8) Curtain air bag modules *
(9) Side impact sensors *
* : if equipped
4-39
Safety system of your vehicle
ٻDriver's front air bag (1) ٻDriver's front air bag (3)
B240B01L B240B03L
The air bag modules are located both A fully inflated air bag, in combination
in the center of the steering wheel with a properly worn seat belt, slows
and in the front passenger’s panel the driver’s or the passenger’s for-
above the glove box. When the ward motion, reducing the risk of
SRSCM detects a sufficiently severe head and chest injury.
impact to the front of the vehicle, it
will automatically deploy the front air After complete inflation, the air bag
bags. immediately starts deflating, enabling
the driver to maintain forward visibility
and the ability to steer or operate oth-
ٻDriver's front air bag (2)
er controls.
B240B02L
4-40
04
ٻDriver's front air bag (3) WARNING
• If an air bag deploys, there may
be a loud noise followed by a
fine dust released in the vehicle.
These conditions are normal
and are not hazardous - the air
bags are packed in this fine
powder. The dust generated
during air bag deployment may
B240B03L cause skin or eye irritation as
well as aggravate asthma for
some persons. Always wash all
WARNING exposed skin areas thoroughly
with cold water and a mild soap
• Do not install or place any ac- after an accident in which the air
cessories (drink holder, cas- bags were deployed.
sette holder, sticker, etc.) on the
front passenger’s panel above • The SRS can function only when
the glove box in a vehicle with a the ignition switch is in the ON
passenger’s air bag. Such ob- position.
jects may become dangerous • Before you replace a fuse or dis-
projectiles and cause injury if connect a battery terminal, turn
the passenger’s air bag inflates. the ignition switch to the LOCK
• When installing a container of position and remove the ignition
liquid air freshener inside the key. Never remove or replace
vehicle, do not place it near the the air bag related fuse(s) when
instrument cluster nor on the in- the ignition switch is in the ON
strument panel surface. position. Failure to heed this
warning will cause the SRS air
It may become a dangerous pro- bag warning light to illuminate.
jectile and cause injury if the
passenger’s air bag inflates.
4-41
Safety system of your vehicle
WARNING
Always use seat belts and child re-
straints – every trip, every time, ev-
eryone! Air bags inflate with con-
OQXI039022 siderable force and in the blink of
ٻPassenger’s front air bag an eye. Seat belts help keep occu-
pants in proper position to obtain
maximum benefit from the air bag.
Even with air bags, improperly and
unbelted occupants can be se-
verely injured when the air bag in-
flates. Always follow the precau-
tions about seat belts, air bags and
occupant safety contained in this
manual.
OQXI039023 • To reduce the chance of serious
Your vehicle is equipped with a Sup- or fatal injuries and receive the
plemental Restraint (Air Bag) System maximum safety benefit from
and lap/shoulder belts at both the your restraint system:
driver and passenger seating posi- • Never place a child in any child
tions. or booster seat in the front seat.
The indications of the system’s pres- • ABC – Always Buckle Children
ence are the letters “AIR BAG” en- in the back seat. It is the safest
graved on the air bag pad cover in the place for children of any age to
steering wheel and the passenger’s ride.
side front panel pad above the glove • Front and side impact air bags
box. can injure occupants improperly
positioned in the front seats.
The SRS consists of air bags installed • Move your seat as far back as
under the pad covers in the center of practical from the front air bags,
the steering wheel and the passen- while still maintaining control of
ger’s side front panel above the glove the vehicle.
box.
4-42
04
• You and your passengers • The SRS is designed to deploy
should never sit or lean unnec- the front air bags only when an
essarily close to the air bags. impact is sufficiently severe and
Improperly positioned drivers when the impact angle is less
and passengers can be severely than 30° from the forward longi-
injured by inflating air bags. tudinal axis of the vehicle. Addi-
• Never lean against the door or tionally, the air bags will only
center console – always sit in an deploy once. Seat belts must be
upright position. worn at all times.
• No objects (such as crash pad • Front air bags are not intended
cover, cellular phone holder, to deploy in side-impact, rear-im-
cup holder, perfume or stickers) pact or rollover crashes. In addi-
should be placed over or near tion, front air bags will not de-
the air bag modules on the steer- ploy in frontal crashes below the
ing wheel, instrument panel, deployment threshold.
windshield glass, and the front • A child restraint system must
passenger’s panel above the never be placed in the front seat.
glove box. Such objects could The infant or child could be se-
cause harm if the vehicle is in a verely injured or killed by an air
crash severe enough to cause bag deployment in case of an
the air bags to deploy. accident.
• Do not attach any objects on the • Children age 12 and under must
front windshield and inside mir- always be properly restrained in
ror. the rear seat. Never allow chil-
• Do not tamper with or discon- dren to ride in the front passen-
nect SRS wiring or other compo- ger seat. If a child over 12 must
nents of the SRS system. Doing be seated in the front seat, he or
so could result in injury, due to she must be properly belted and
accidental deployment of the air the seat should be moved as far
bags or by rendering the SRS in- back as possible.
operative. • For maximum safety protection
• If the SRS air bag warning light in all types of crashes, all occu-
remains illuminated while the pants including the driver
vehicle is being driven, we rec- should always wear their seat
ommend that the system be in- belts whether or not an air bag is
spected by an authorized HYUN- also provided at their seating
DAI dealer. position to minimize the risk of
severe injury or death in the
• Air bags can only be used once event of a crash. Do not sit or
– we recommend that the sys- lean unnecessarily close to the
tem be replaced by an autho- air bag while the vehicle is in
rized HYUNDAI dealer. motion.
4-43
Safety system of your vehicle
OJK032063
The actual air bags in the vehicle may differ from the
illustration.
4-44
04
WARNING • Do not place any objects over
the air bag or between the air
Do not allow the passengers to lean bag and yourself. Also, do not
their heads or bodies onto doors, put attach any objects around the
their arms on the doors, stretch their area the air bag inflates such as
arms out of the window, or place ob- the door, side door glass, front
jects between the doors and passen- and rear pillar.
gers when they are seated on seats • Do not place any objects be-
equipped with side and/or curtain air tween the door and the seat.
bags. They may become dangerous
projectiles if the side air bag in-
flates.
WARNING
• Do not put any objects between
• The side impact air bag is sup- the side air bag label and seat
plemental to the driver’s and the cushion. It could cause harm if
passenger’s seat belt systems the vehicle is in a crash severe
and is not a substitute for them. enough to cause the air bags to
Therefore your seat belts must deploy.
be worn at all times while the ve- • To prevent unexpected deploy-
hicle is in motion. The air bags ment of the side impact air bag
deploy only in certain side im- that may result in personal inju-
pact conditions severe enough ry, avoid impact to the side im-
to cause significant injury to the pact sensor when the ignition
vehicle occupants. switch is on.
• For best protection from the • If the seat or seat cover is dam-
side impact air bag system and aged, we recommend that the
to avoid being injured by the de- system be serviced by an autho-
ploying side impact air bag, both rized HYUNDAI dealer.
front seat occupants should sit
in an upright position with the • Inform the dealer that your vehi-
seat belt properly fastened. The cle is equipped with side impact
driver’s hands should be placed air bags.
on the steering wheel at the 9:00
and 3:00 positions. The passen-
ger’s arms and hands should be
placed on their laps.
• Do not use any accessory seat
covers.
• Use of seat covers could reduce
or prevent the effectiveness of
the system.
• Do not install any accessories
on the side or near the side im-
pact air bag.
4-45
Safety system of your vehicle
4-46
04
• Do not allow the passengers to Why didn’t my air bag go off in a
lean their heads or bodies onto collision? (Inflation and non-infla-
doors, put their arms on the tion conditions of the air bag)
doors, stretch their arms out of There are many types of accidents
the window, or place objects be- in which the air bag would not be
tween the doors and passengers expected to provide additional
when they are seated on seats protection.
equipped with side and/or cur-
tain air bags. These include rear impacts, sec-
ond or third collisions in multiple
• Do not open or repair the side impact accidents, as well as low
curtain air bags. speed impacts.
• Never try to open or repair any
components of the side curtain
air bag system. We recommend
that the system be serviced by
an authorized HYUNDAI dealer.
Failure to follow the above men-
tioned instructions can result in
injury or death to the vehicle occu-
pants in an accident.
4-47
Safety system of your vehicle
OQXI039026/OQXI039027/OQXI039028/OQXI039029
* : if equipped
4-48
04
WARNING Air bag inflation conditions
4-49
Safety system of your vehicle
OQXI039032
4-50
04
OQXI039033 OQXI039034
• Front air bags may not inflate in • Just before impact, drivers often
side impact collisions, because oc- brake heavily. Such heavy braking
cupants move to the direction of lowers the front portion of the vehi-
the collision, and thus in side im- cle causing it to “ride” under a vehi-
pacts, frontal air bag deployment cle with a higher ground clearance.
would not provide additional occu- Air bags may not inflate in this “un-
pant protection. der-ride” situation because decel-
However, side impact or curtain air eration forces that are detected by
bags may inflate depending on the sensor may be significantly re-
intensity, vehicle speed and angles duced by such “under-ride” colli-
of impact. sions.
OBH038060 OQXI039035
4-51
Safety system of your vehicle
SRS Care
The SRS is virtually maintenance-free
and so there are no parts you can
safely service by yourself. If the SRS
air bag warning light does not illumi-
nate, or continuously remains on, we
recommend that the system be in-
spected by an authorized HYUNDAI
dealer.
OQXI039036
We recommend that the any work on
• Air bags may not inflate if the vehi- the SRS system, such as removing,
cle collides with objects such as installing, repairing, or any work on
utility poles or trees, where the the steering wheel, the front passen-
point of impact is concentrated and ger’s panel, front seats and roof rails
the collision energy is absorbed by be performed by an authorized
the vehicle structure. HYUNDAI dealer. Improper handling
of the SRS system may result in seri-
ous personal injury.
WARNING
• Modification to SRS compo-
nents or wiring, including the
addition of any kind of badges
to the pad covers or modifica-
tions to the body structure, can
adversely affect SRS perfor-
mance and lead to possible inju-
ry.
• For cleaning the air bag pad
covers, use only a soft, dry cloth
or one which has been moist-
ened with plain water. Solvents
or cleaners could adversely af-
fect the air bag covers and prop-
er deployment of the system.
4-52
04
• No objects should be placed Additional safety precautions
over or near the air bag modules • Never let passengers ride in the
on the steering wheel, instru- cargo area or on top of a fold-
ment panel, and the front pas- ed-down back seat. All occupants
senger’s panel above the glove should sit upright, fully back in their
box, because any such object seats with their seat belts on and
could cause harm if the vehicle their feet on the floor.
is in a crash severe enough to
cause the air bags to inflate. • Passengers should not move
out of or change seats while the
• If the air bags inflate, we recom- vehicle is moving. A passenger
mend that the system be re- who is not wearing a seat belt
placed by an authorized HYUN- during a crash or emergency stop
DAI dealer. can be thrown against the inside of
• Do not tamper with or discon- the vehicle, against other occu-
nect SRS wiring, or other com- pants, or out of the vehicle.
ponents of the SRS system. Do- • Each seat belt is designed to re-
ing so could result in injury, due strain one occupant. If more than
to accidental inflation of the air one person uses the same seat
bags or by rendering the SRS in- belt, they could be seriously in-
operative. jured or killed in a collision.
• If components of the air bag • Do not use any accessories on
system must be discarded, or if seat belts. Devices claiming to im-
the vehicle must be scrapped, prove occupant comfort or reposi-
certain safety precautions must tion the seat belt can reduce the
be observed. An authorized protection provided by the seat belt
HYUNDAI dealer knows these and increase the chance of serious
precautions and can give you injury in a crash.
the necessary information. Fail-
ure to follow these precautions • Passengers should not place
and procedures could increase hard or sharp objects between
the risk of personal injury. themselves and the air bags.
Carrying hard or sharp objects on
• If your car was flooded and has your lap or in your mouth can result
soaked carpeting or water on in injuries if an air bag inflates.
the flooring, you shouldn’t try to
start the engine; we recommend • Keep occupants away from the
that you contact an authorized air bag covers. All occupants
HYUNDAI dealer. should sit upright, fully back in their
seats with their seat belts on and
their feet on the floor. If occupants
are too close to the air bag covers,
they could be injured if the air bags
inflate.
4-53
Safety system of your vehicle
4-54
5. Convenient features of
your vehicle
i Information
After unlocking the doors, the doors
will lock automatically after 30 sec-
OIB034040 onds unless a door is opened.
Your HYUNDAI uses a remote key,
which you can use to lock or unlock a Tailgate unlocking
door (and tailgate) and even start the
To unlock:
engine.
1. Press the Tailgate Unlock button
1. Door Lock
(3) on the remote key for more
2. Door Unlock than one second.
3. Tailgate Unlock 2. The hazard warning lights will blink
two times. Once the tailgate is
Locking opened and then closed, the tail-
gate will lock automatically.
To lock :
1. Close all doors, engine hood and
tailgate. i Information
2. Press the Door Lock button (1) on • After unlocking the tailgate, the
the remote key. tailgate will lock automatically.
3. The doors will lock. The hazard • The word “HOLD” is written on the
warning lights will blink once. button to inform you that you must
4. Make sure the doors are locked by press and hold the button for more
checking the position of the door than one second.
lock button inside the vehicle.
WARNING
Do not leave the keys in your vehi-
cle with unsupervised children.
Unattended children could place
the key in the ignition switch and
may operate power windows or
other controls, or even make the
vehicle move, which could result
in serious injury or death.
5-4
05
Start-up Mechanical key
For detailed information refer to “Key ٻType A
Ignition Switch” in chapter 5.
NOTICE
To prevent damaging the remote
key:
• Keep the remote key away from
water or any liquid and fire. If the
inside of the remote key gets
damp (due to drinks or mois- OYDECO2231
ture), or is heated, internal cir- ٻType B
cuit may malfunction, excluding
the car from the warranty.
• Avoid dropping or throwing the
remote key.
• Protect the remote key from ex-
treme temperatures.
OIB044178
Type B
To unfold the key, press the release
button then the key will unfold auto-
matically.
To fold the key, fold the key manually
while pressing the release button.
NOTICE
Do not fold the key without press-
ing the release button. This may
damage the key.
5-5
Convenient features of your vehicle
5-6
05
Battery replacement Smart key (if equipped)
If the remote key is not working prop- ٻType A
erly, try replacing the battery with a
new one.
OIB044179
ٻType B
OIB044180
Battery Type: CR2032
To replace the battery:
1. Insert a slim tool into the slot and
gently pry open the cover.
2. Remove the old battery and insert
the new battery. Make sure the
battery position is correct. OQXI049001
3. Reinstall the rear cover of the re- Your HYUNDAI uses a Smart Key,
mote key. which you can use to lock or unlock a
door (and tailgate) and even start the
engine.
If you suspect your remote key might
have sustained some damage, or you 1. Door Lock
feel your remote key is not working 2. Door Unlock
correctly, it is recommended that you 3. Tailgate Unlock
contact an authorized HYUNDAI
4. Panic
dealer.
i Information
An inappropriately dis-
posed battery can be harm-
ful to the environment and
human health. Dispose the
battery according to your
local law(s) and regulation.
5-7
Convenient features of your vehicle
i Information
The door handle button will only oper-
ate when the smart key is within 0.7~1
m (28~40 in.) from the outside door
handle.
5-8
05
Unlocking Tailgate unlocking
To unlock:
1. Carry the smart key.
2. Either press the tailgate handle
button or press the Tailgate Unlock
button (3) on the smart key for
more than one second.
3. The hazard warning lights will blink
two times.
Once the tailgate is opened and then
OQXI049002 closed, the tailgate will lock automati-
To unlock: cally.
1. Carry the Smart Key.
2. Either press the door handle but- i Information
ton or press the Door Unlock but-
ton (2) on the smart key. After unlocking the tailgate, the tail-
gate will lock automatically after 30
3. The doors will unlock. The hazard seconds unless the tailgate is opened.
warning lights will blink two times.
i Information
• The door handle button will only
operate when the smart key is with-
in 1 m (40 in.) from the outside door
handle. Other people can also open
the doors without the smart key in
possession.
• After unlocking the doors, the doors
will lock automatically after 30 sec-
onds unless a door is opened.
5-9
Convenient features of your vehicle
Start-up
You can start the engine without in-
serting the key. For detailed informa-
tion refer to the Engine Start/Stop
button in chapter 5.
OIB044175
5-10
05
Smart key precautions NOTICE
The smart key will not work if any of Keep the smart key away from
the following occur: electromagnetic materials that
• The smart key is close to a radio blocks electromagnetic waves to
transmitter such as a radio station the key surface.
or an airport which can interfere
with normal operation of the trans- Battery replacement
mitter.
• The smart key is near a mobile two
way radio system or a cellular
phone.
• Another vehicle’s smart key is be-
ing operated close to your vehicle.
When the smart key does not work
correctly, open and close the door
with the mechanical key. If you have
a problem with the smart key, it is rec-
ommended that you contact an au- OLF044008
thorized HYUNDAI dealer.
If the smart key is in close proximity If the Smart Key is not working prop-
to your mobile phone, the signal could erly, try replacing the battery with a
be blocked by your mobile phones new one.
normal operational signals. This is Battery Type: CR2032
especially important when the phone To replace the battery:
is active such as making and receiv-
ing calls, text messaging, and/or 1. Pry open the rear cover of the
sending/receiving emails. Avoid plac- smart key.
ing the smart key and your mobile 2. Remove the old battery and insert
phone in the same pants or jacket the new battery. Make sure the
pocket and always try to maintain an battery position is correct.
adequate distance between the two 3. Reinstall the rear cover of the
devices. smart key.
If you suspect your smart key might
i Information have sustained some damage, or you
feel your smart key is not working
Changes or modifications not express- correctly, it is recommended that you
ly approved by the party responsible contact an authorized HYUNDAI
for compliance could void the user’s dealer.
authority to operate the equipment. If
the keyless entry system is inoperative
due to changes or modifications not ex-
pressly approved by the party respon-
sible for compliance, it will not be cov-
ered by your manufacturer’s vehicle
warranty.
5-11
Convenient features of your vehicle
i Information WARNING
In order to prevent theft of your
An inappropriately dis- vehicle, do not leave spare keys
posed battery can be harm- anywhere in your vehicle. Your
ful to the environment and immobilizer password is a custom-
human health. Dispose the er unique password and should be
battery according to your kept confidential.
local law(s) and regulation.
NOTICE
Immobilizer system
The immobilizer system protects your The transponder in your key is an
vehicle from theft. If an improperly important part of the immobiliz-
coded key (or other device) is used, er system. It is designed to give
the engine’s fuel system is disabled. years of trouble-free service, how-
ever you should avoid exposure
When the ignition switch is placed in to moisture, static electricity and
the ON position, the immobilizer sys- rough handling. Immobilizer sys-
tem indicator should come on briefly, tem malfunction could occur.
then go off. If the indicator starts to
blink, the system does not recognize
the coding of the key.
Place the ignition switch to the LOCK/
OFF position, then place the ignition
switch to the ON position again.
The system may not recognize your
key’s coding if another immobilizer
key or other metal object (i.e., key
chain) is near the key. The engine
may not start because the metal may
interrupt the transponder signal from
transmitting normally.
If the system repeatedly does not rec-
ognize the coding of the key, it is rec-
ommended that you contact your
HYUNDAI dealer.
Do not attempt to alter this system or
add other devices to it. Electrical
problems could result that may make
your vehicle inoperable.
5-12
05
DOOR LOCKS
Operating door locks from out- Remote key
side the vehicle
Mechanical key
OQXI049004
5-13
Convenient features of your vehicle
OQXI049005
1. Door lock
2. Door unlock
the outside door handle while carry- • To unlock a door, push the door
ing the smart key with you or press lock button (1) to the “Unlock” posi-
the door lock button on the smart key. tion.
To unlock the doors, press the button • To lock a door, push the door lock
on the outside door handle while car- button (1) to the “Lock” position.
rying the smart key with you or press • To open a door, pull the door han-
the door unlock button on the smart dle (2) outward.
key.
Once the doors are unlocked, they
may be opened by pulling the door
handle.
When closing the door, push the door
by hand. Make sure that doors are
closed securely.
5-14
05
• If the inner door handle of the driv- With the central door lock/un-
er’s door is pulled when the door lock switch
lock button is in the lock position,
the button is unlocked and door
opens.
• Front doors cannot be locked if the
key is in the ignition switch and any
front door is open.
• Doors cannot be locked if the smart
key is in the vehicle and any door
is open.
OQXI049007
WARNING
• The doors should always be ful-
ly closed and locked while the
vehicle is in motion. If the doors
are unlocked, the risk of being
thrown from the vehicle in a
crash is increased.
• Do not pull the inner door han-
dle of the driver’s or passen-
ger’s door while the vehicle is
moving.
5-15
Convenient features of your vehicle
WARNING WARNING
Do not leave children or animals Opening a door when something is
unattended in your vehicle. An en- approaching may cause damage
closed vehicle can become ex- or injury. Be careful when opening
tremely hot, causing death or seri- doors and watch for vehicles, mo-
ous injury to unattended children torcycles, bicycles or pedestrians
or animals who cannot escape the approaching the vehicle in the
vehicle. Children might operate path of the door.
features of the vehicle that could
injure them, or they could encoun-
ter other harm, possibly from WARNING
someone gaining entry to the vehi- If you stay in the vehicle for a long
cle. time while the weather is very hot
or cold, there are risks of injuries
WARNING or danger to life. Do not lock the
vehicle from the outside when
Always secure your vehicle someone is in the vehicle.
Leaving your vehicle unlocked in-
creases the potential risk to you or Auto door lock/unlock features
others from someone hiding in
your vehicle. Impact sensing door unlock sys-
tem
To secure your vehicle, while de-
pressing the brake, move the shift All doors will be automatically un-
lever to the P (Park) position (for locked when an impact causes the air
Dual clutch transmission vehicle) bags to deploy.
or first gear or R (Reverse) posi-
tion (for Manual transmission vehi- Speed sensing door lock system
cle), engage the parking brake, All doors will be automatically locked
and place the ignition switch in the when vehicle speed exceeds 15 km/h
LOCK/OFF position, close all win- (9 mph).
dows, lock all doors, and always
take the key with you.
5-16
05
Child-protector rear door locks
OQXI049008
WARNING
If children accidently open the rear
doors while the vehicle is in mo-
tion, they could fall out of the vehi-
cle. The rear door safety locks
should always be used whenever
children are in the vehicle.
5-17
Convenient features of your vehicle
7+()7ǘ$/$506<67(0ǣ,)(48,33('Ǥ
This system helps to protect your ve-
hicle and valuables. The horn will
i Information
sound and the hazard warning lights • Do not lock the doors until all pas-
will blink continuously if any of the fol- sengers have left the vehicle. If the
lowing occurs: remaining passenger leaves the ve-
- A door is opened without using the hicle when the system is armed, the
remote key or smart key. alarm will be activated.
- The tailgate is opened without us- • If the vehicle is not disarmed with
ing the remote key or smart key. the remote key or smart key, open
- The engine hood is opened. the doors by using the mechanical
key and place the ignition switch in
The alarm continues for 30 seconds, the ON position (for remote key) or
then the system resets. To turn off start the engine (for smart key) and
the alarm, unlock the doors with the wait for 30 seconds.
remote key or smart key.
• When the system is disarmed but a
The Theft Alarm System automatical- door or tailgate is not opened within
ly sets 30 seconds after you lock the 30 seconds, the system will be re-
doors and the tailgate. For the sys- armed.
tem to activate, you must lock the
doors and the tailgate from outside
the vehicle with the remote key or
smart key or by pressing the button
on the outside of the door handles
with the smart key in your posses-
sion.
The hazard warning lights will blink
and the chime will sound once to indi-
cate the system is armed.
Once the security system is set,
opening any door, the tailgate, or the
hood without using the remote key or
smart key will cause the alarm to acti-
vate.
The Theft Alarm System will not set if
the hood, the tailgate, or any door is
not fully closed. If the system will not
set, check the hood, the tailgate, or
the doors are fully closed.
Do not attempt to alter this system or
add other devices to it.
5-18
05
TAILGATE
Opening the tailgate Closing the tailgate
To close the tailgate, lower and push
down the tailgate firmly. Make sure
that the tailgate is securely latched.
WARNING
Always keep the tailgate lid com-
pletely closed while the vehicle is
in motion. If it is left open or ajar,
poisonous exhaust gases contain-
OQXI049009 ing carbon monoxide (CO) may en-
ter the vehicle and serious illness
• The tailgate is locked or unlocked or death may result.
when all doors are locked or un-
locked with the key, remote key,
smart key or central door lock/ un- WARNING
lock switch.
Rear cargo area
• If unlocked, the tailgate can be
opened by pressing the handle Occupants should never ride in
and pulling it up. the rear cargo area where no re-
straints are available. To avoid in-
jury in the event of an accident or
i Information sudden stops, occupants should
always be properly restrained.
In cold and wet climates, door lock and
door mechanisms may not work prop-
erly due to freezing conditions. WARNING
NOTICE
Make certain that you close the
tailgate before driving your vehi-
cle. Possible damage may occur to
the tailgate lift cylinders and at-
taching hardware if the tailgate is
not closed prior to driving.
OQXI049011
5-19
Convenient features of your vehicle
5-20
05
WINDOWS
Power windows (if equipped)
OQXI049012
* : if equipped
5-21
Convenient features of your vehicle
5-22
05
To reset the power windows Automatic reverse (if equipped)
If the power windows do not operate
normally, the automatic power win-
dow system must be reset as follows:
1. Place the ignition switch to the ON
position.
2. Close the window and continue
pulling up on the power window
switch for at least 1 second.
If the power windows do not operate
properly after resetting, it is recom- OIB024001
mended that the system be checked If a window senses any obstacle
by an authorized HYUNDAI dealer. while it is closing automatically, it will
stop and lower approximately 30 cm
WARNING (12 in.) to allow the object to be
cleared.
The automatic reverse feature If the window detects the resistance
doesn’t activate while resetting while the power window switch is
power window system. Make sure pulled up continuously, the window
body parts or other objects are will stop upward movement then low-
safely out of the way before clos- er approximately 2.5 cm (1 in.).
ing the windows to avoid injuries
or vehicle damage. If the power window switch is pulled
up continuously again within 5 sec-
onds after the window is lowered by
the automatic window reverse fea-
ture, the automatic window reverse
will not operate.
i Information
The automatic reverse feature is only
active when the “auto up” feature is
used by fully pulling up the switch to
the second detent.
5-23
Convenient features of your vehicle
OQXI049013
5-24
05
WARNING Manual windows (if equipped)
• NEVER leave the keys in your
vehicle with unsupervised chil-
dren, when the engine is run-
ning.
• NEVER leave any child unat-
tended in the vehicle. Even very
young children may inadvertent-
ly cause the vehicle to move, en-
tangle themselves in the win-
dows, or otherwise injure OYC046423
themselves or others. To raise or lower the window, turn the
• Always double check to make window regulator handle clockwise or
sure all arms, hands, head and counterclockwise in right side. And
other obstructions are safely left side is opposite direction.
out of the way before closing a
window.
WARNING
• Do not allow children to play
with the power windows. Keep When opening or closing the win-
the driver’s door power window dows, make sure your passenger’s
lock switch in the LOCK posi- arms, hands and body are safely
tion (pressed). Serious injury out of the way.
can result from unintentional
window operation by the child.
• Do not extend your head, arms
or body outside the win
5-25
Convenient features of your vehicle
HOOD
Opening the hood
OQXI049016
5-26
05
WARNING
Always double check to be sure
that the hood is firmly latched be-
fore driving away. Check there is
no hood open warning light or
message displayed on the instru-
ment cluster. Driving with the hood
opened may cause a total loss of
visibility, which might result in an
accident.
WARNING
• Before closing the hood, ensure
that all obstructions are re-
moved from the hood opening.
Closing the hood with an ob-
struction present in the hood
opening may result in property
damage or severe personal inju-
ry.
• Do not leave gloves, rags or any
other combustible material in
the engine compartment. Doing
so may cause a heat-induced
fire.
• Do not move the vehicle with the
hood raised. The view will be
blocked and the hood could fall
or be damaged.
5-27
Convenient features of your vehicle
681522)ǣ,)(48,33('Ǥ
Sliding the sunroof
Pressing the sunroof control lever
backward or forward momentarily to
the second detent position complete-
ly opens or closes the sunroof even
when the switch is released. To stop
the sunroof at the desired position
while the sunroof is in operation,
press the sunroof control lever back-
ward or forward and release the
OQXI049017
switch.
If your vehicle is equipped with a sun-
roof, you can slide or tilt your sunroof
with the sunroof control switch locat- i Information
ed on the overhead console. To reduce wind noise while driving, it
The sunroof can only be opened, is recommended that you drive with
closed, or tilted when the ignition the sunroof slightly closed (stop the
switch is in the ON position. sunroof about 5 cm before the maxi-
mum slide open position).
Sunroof opening and closing
NOTICE
To prevent damage to the sunroof
and the motor, do not continue to
press the sunroof control lever af-
ter the sunroof is in the fully open,
closed or tilt position(s).
OQXI049018
To open:
Press the sunroof control lever back-
ward to the first detent position. Re-
lease the switch when you want the
sunroof to stop.
To close:
Press the sunroof control lever for-
ward to the first detent position. Re-
lease the switch when you want the
sunroof to stop.
5-28
05
Automatic reversal Tilting the sunroof
OLFC044035CN OQXI049019
5-29
Convenient features of your vehicle
OAD045037
The sunshade will open automatically
with the sunroof when the glass panel
moves. If you want it closed, move
the sunshade manually.
NOTICE
The sunroof is made to slide to-
gether with the sunshade. Do not
leave the sunshade closed while
the sunroof is open.
5-30
05
Do not release the lever until the op-
eration is completed.
If you release the lever during opera-
tion, try again from step 2.
i Information
• If the sunroof does not reset when
the vehicle battery is disconnected
or discharged, or related fuse is
blown, the sunroof may not operate
normally.
• For more detailed information, we
recommend that you contact an au-
thorized HYUNDAI dealer.
5-31
Convenient features of your vehicle
The fuel filler door must be opened Closing the fuel filler door
from inside the vehicle by pulling up 1. To install the fuel tank cap (2), turn
the fuel filler door opener. it clockwise until it “clicks” once.
1. Stop the engine. This indicates that the cap is se-
2. Pull the fuel filler door opener up. curely tightened.
2. Close the fuel filler door (1) and
push it lightly and make sure that it
is securely closed.
WARNING
Petrol is highly flammable and ex-
plosive. Failure to follow these
guidelines may result in SERIOUS
INJURY or DEATH:
OQXI049021
• Read and follow all warnings
3. Pull the fuel filler door out (1) to ful- posted at the gas station.
ly open.
• Before refueling, note the loca-
4. To remove the fuel tank cap (2), tion of the Emergency Petrol
turn it counterclockwise. You may Shut-Off, if available, at the gas
hear a hissing noise as the pres- station.
sure inside the tank equalizes.
• Before touching the fuel nozzle,
5. Place the cap on the fuel filler door. you should eliminate the poten-
tial build-up of static electricity
by touching a metal part of the
vehicle, a safe distance away
from the fuel filler neck, nozzle,
or other gas source, with your
bare hand.
5-32
05
• Do not use cellular phones while • When refueling, always move
refueling. Electric current and/or the shift lever to the P (Park) po-
electronic interference from cel- sition (for dual clutch transmis-
lular phones can potentially ig- sion vehicle) or first gear or R
nite fuel vapors and cause a fire. (Reverse) position (for manual
• Do not get back into a vehicle transmission vehicle), set the
once you have begun refueling. parking brake, and place the ig-
You can generate a build-up of nition switch to the LOCK/OFF
static electricity by touching, position. Sparks produced by
rubbing or sliding against any electrical components related to
item or fabric capable of produc- the engine can ignite fuel vapors
ing static electricity. Static elec- causing a fire.
tricity discharge can ignite fuel • Do not use matches or a lighter
vapors causing a fire. and do not smoke or leave a lit
If you must re-enter the vehicle, cigarette in your vehicle while at
you should once again eliminate a gas station, especially during
potentially dangerous static refueling.
electricity discharge by touch- • Do not over-fill or top-off your
ing a metal part of the vehicle, vehicle tank, which can cause
away from the fuel filler neck, petrol spillage.
nozzle or other petrol source, • If a fire breaks out during refuel-
with your bare hand. ing, leave the vicinity of the ve-
• When using an approved porta- hicle, and immediately contact
ble fuel container, be sure to the manager of the gas station
place the container on the and then contact the local fire
ground prior to refueling. Static department. Follow any safety
electricity discharge from the instructions they provide.
container can ignite fuel vapors • If pressurized fuel sprays out, it
causing a fire. Once refueling can cover your clothes or skin
has begun, contact between and thus subject you to the risk
your bare hand and the vehicle of fire and burns. Always re-
should be maintained until the move the fuel cap carefully and
filling is complete. slowly. If the cap is venting fuel
• Use only approved portable or if you hear a hissing sound,
plastic fuel containers designed wait until the condition stops
to carry and store petrol. before completely removing the
cap.
• Always check that the fuel cap is
installed securely to prevent
fuel spillage in the event of an
accident.
5-33
Convenient features of your vehicle
i Information
• Make sure to refuel your vehicle
according to the “Fuel Require-
ments” suggested in the fore-
word chapter.
• Do not spill fuel on the exterior
surfaces of the vehicle. Any type
of fuel spilled on painted surfac-
es may damage the paint.
NOTICE
If the fuel filler cap requires re-
placement, use only a genuine
HYUNDAI cap or the equivalent
specified for your vehicle. An in-
correct fuel filler cap can result in
a serious malfunction of the fuel
system or emission control sys-
tem.
5-34
05
STEERING WHEEL
Electric power steering (EPS) i Information
The system assists you with steering
the vehicle. If the engine is off or if the The following symptoms may occur
power steering system becomes in- during normal vehicle operation:
operative, the vehicle may still be • The steering effort may be high im-
steered, but it will require increased mediately after placing the ignition
steering effort. switch in the ON position.
Also, the steering effort becomes This happens as the system per-
heavier as the vehicle’s speed in- forms the EPS system diagnostics.
creases and becomes lighter as the When the diagnostics is completed,
vehicle’s speed decreases for better the steering wheel will return to its
control of the steering wheel. normal condition.
Should you notice any change in the • A click noise may be heard from the
effort required to steer during normal EPS relay after the ignition switch is
vehicle operation, we recommend placed to the ON or LOCK/OFF po-
that the system be checked by an au- sition.
thorized HYUNDAI dealer. • Motor noise may be heard when the
vehicle is at stop or at a low driving
NOTICE speed.
If the Electric Power Steering Sys- • When you operate the steering
tem does not operate normally, the wheel in low temperature, abnor-
warning light ( ) will illuminate on mal noise may occur. If temperature
the instru- ment cluster. The rises, the noise will disappear. This
steering wheel may become diffi- is a normal condition.
cult to control or operate. Take
your vehicle to an authorized WARNING
HYUNDAI dealer and have the sys-
tem checked as soon as possible. Never adjust the steering wheel
while driving. You may lose steer-
ing control and cause severe per-
sonal injury, death or accidents.
5-35
Convenient features of your vehicle
Horn
OQXI049022
OQXI049023
Pull down the lock-release lever (1)
on the steering wheel column and ad- To sound the horn, press the area in-
just the steering wheel angle (2). dicated by the horn symbol on your
Move the steering wheel, so it points steering wheel (see illustration). The
toward your chest, not toward your horn will operate only when this area
face. Make sure you can see the in- is pressed.
strument panel warning lights and
gauges.
NOTICE
After adjusting, pull up the lock-re-
lease lever (3) to lock the steering Do not strike the horn severely to
wheel in place. Push the steering operate it, or hit it with your fist. Do
wheel both up and down to be certain not press on the horn with a
it is locked in position. Always adjust sharp-pointed object.
the position of the steering wheel be-
fore driving.
5-36
05
0,55256
Inside rearview mirror Make this adjustment before you start
Before you start driving, adjust the driving and while the day/night lever
rearview mirror to the center on the is in the day position.
view through the rear window. Pull the day/night lever toward you to
reduce glare from the headlights of
the vehicles behind you during night
WARNING driving.
Make sure your line of sight is not Remember that you lose some rear-
obstructed. Do not place objects in view clarity in the night position.
the rear seat, cargo area, or behind
the rear headrests which could in- Blue Link® center (if equipped)
terfere with your vision through
the rear window.
WARNING
To prevent serious injury during
an accident or deployment of the
air bag, do not modify the rearview
mirror and do not install a wide
mirror.
OQXI049073
OQXI049024
[ٻA] : Day, [B] :Night
5-37
Convenient features of your vehicle
WARNING
Rearview mirrors
• Both right and left outside rear
view mirror are convex. OIB034041
WARNING
Do not adjust or fold the outside
rearview mirrors while the vehicle
is moving. This could result in loss
of control, and an accident which OQXI049025
could cause death, serious injury Electric type (if equipped)
or property damage.
Adjusting the rearview mirrors:
Move the lever (1) to the L (Left) or R
NOTICE (Right) to select the rearview mirror
• Do not scrape ice off the mirror you would like to adjust.
face; this may damage the sur- Use the mirror adjustment control to
face of the glass. position the selected mirror up, down,
• If the mirror is jammed with ice, left or right.
do not adjust the mirror by force.
Use an approved spray de-icer
(not radiator antifreeze) spray,
or a sponge or soft cloth with
very warm water, or move the
vehicle to a warm place and al-
low the ice to melt.
5-38
05
NOTICE
• The mirrors stop moving when
they reach the maximum adjust-
ing angles, but the motor contin-
ues to operate while the switch
is pressed. Do not press the
switch longer than necessary,
the motor may be damaged.
• Do not attempt to adjust the out-
side rearview mirror by hand or OQXI049027
NOTICE
The electric type outside rearview
mirror operates even though the
ignition switch is in the ACC posi-
tion. However, to prevent unneces-
OQXI049026
sary battery discharge, do not ad-
Manual type just the mirrors longer than
To fold the outside rearview mirror, necessary while the engine is not
grasp the housing of the mirror and running.
then fold it toward the rear of the ve-
hicle.
NOTICE
Do not fold the electric type out-
side rearview mirror by hand. It
could cause motor failure.
5-39
Convenient features of your vehicle
,167580(17&/867(5
ٻType A
ٻType B
OQXI049100/OQXI049101
5-40
05
Instrument Cluster Control ٻType A
WARNING
Never adjust the instrument clus-
ter while driving. This could result
in loss of control and lead to an ac-
cident that may cause death, seri-
ous injury, or property damage.
OIB044112
OHCR046110
5-41
Convenient features of your vehicle
Gauges Tachometer
Speedometer ٻType A
ٻType A
OQXI049104
ٻType B
OQXI049102
ٻType B
OQXI049105
NOTICE
Do not operate the engine within
the tachometer’s RED ZONE. This
may cause severe engine damage.
5-42
05
Engine Coolant Temperature WARNING
Gauge
ٻType A Never remove the radiator cap
when the engine is hot. The engine
coolant is under pressure and
could cause severe burns. Wait
until the engine is cool before add-
ing coolant to the reservoir.
Fuel Gauge
ٻType A
OQXI049106
ٻType B
OQXI049108
ٻType B
OQXI049107
NOTICE
If the gauge pointer moves beyond
the normal range area toward the
OQXI049109
“H” position, it indicates overheat-
ing that may damage the engine. This gauge indicates the approximate
Do not continue driving with an amount of fuel remaining in the fuel
overheated engine. If your vehicle tank.
overheats, refer to “If the Engine
Overheats” in chapter 6.
5-43
Convenient features of your vehicle
i Information Odometer
ٻType A
• The fuel tank capacity is given in
chapter 8.
• The fuel gauge is supplemented by a
low fuel warning light, which will
illuminate when the fuel tank is
nearly empty.
• On inclines or curves, the fuel gauge
pointer may fluctuate or the low fuel
warning light may come on earlier
OQXI049110
than usual due to the movement of
fuel in the tank. ٻType B
WARNING
Fuel Gauge
Running out of fuel can expose ve-
hicle occupants to danger.
You must stop and obtain addi-
tional fuel as soon as possible af-
OIB044115
ter the warning light comes on or
when the gauge indicator comes The odometer indicates the total dis-
close to the “E (Empty)” level. tance that the vehicle has been driv-
en and should be used to determine
when periodic maintenance should
NOTICE
be performed.
Avoid driving with a very low fuel - Odometer range : 0 ~ 1599999 kilo-
level. Running out of fuel could meters or 999999 miles.
cause the engine to misfire dam-
aging the catalytic converter.
i Information
It is forbidden to alter the odometer of
all vehicles with the intent to change
the mileage registered on the odome-
ter. The alteration may void your war-
ranty coverage.
5-44
05
Outside Temperature Gauge Transmission Shift Indicator
ٻType A Duel clutcansmission shifter in-
dicator
ٻType A
OQXI049111
ٻType B
OQXI049112
ٻType B
OIB044155
5-45
Convenient features of your vehicle
OHCR046129
• Shifting up : S2, S3, S4, S5, S6 The pop-up that indicates the current
• Shifting down : T2, T3, T4, T5 gear position is displayed in the clus-
ter for about 2 seconds when shifting
into other positions (P/R/N/D).
5-46
05
Warning and indicator lights Seat Belt Warning
Light
i Information - Warning light
Make sure that all warning lights are This warning light informs the driver
OFF after starting the engine. If any that the seat belt is not fastened.
light is still ON, this indicates a situa-
tion that needs attention.
For more details, refer to the “Seat
Belts” in chapter 2.
Air bag Warning Light
Parking Brake & Brake
Fluid Warning Light
This warning light illuminates:
• Once you set the ignition switch or
Engine Start/Stop button to the ON This warning light illuminates:
position. • Once you set the ignition switch or
Engine Start/Stop button to the ON
- It illuminates for approximately 6 position.
seconds and then goes off.
- It illuminates for approximately 3
• When there is a malfunction with seconds
the SRS.
- It remains on if the parking brake
In this case, we recommend that is applied.
you have the vehicle inspected by
an authorized HYUNDAI dealer. • When the parking brake is applied.
• When the brake fluid level in the
reservoir is low.
- If the warning light illuminates
with the parking brake released, it
indicates the brake fluid level is
low.
5-47
Convenient features of your vehicle
5-48
05
Electric Power Steer- NOTICE
ing (EPS) Warning - Petrol Engine
Light If the Malfunction Indicator Lamp
(MIL) illuminates, potential catalyt-
This warning light illuminates: ic converter damage is possible
• Once you set the ignition switch or which could result in loss of en-
Engine Start/Stop button to the ON gine power.
position. In this case, we recommend that
- It illuminates for approximately 3 you have the vehicle inspected by
seconds and then goes off. an authorized HYUNDAI dealer as
soon as possible.
• When there is a malfunction with
the EPS.
In this case, we recommend that NOTICE
you have the vehicle inspected by - Diesel Engine with DPF
an authorized HYUNDAI dealer. (if equipped)
When the Malfunction Indicator
Malfunction Indicator Lamp (MIL) blinks, it may stop
Lamp (MIL) blinking after driving the vehicle:
- at more than 60km/h (37 mph), or
- at more than 2nd gear with 1500 ~
This warning light illuminates: 2000 engine rpm for a certain
• Once you set the ignition switch or time (for about 25 minutes).
Engine Start/Stop button to the ON If the Malfunction Indicator Lamp
position. (MIL) continues to blink in spite of
- It illuminates for approximately 3 the procedure, we recommend that
seconds and then goes off. you have the DPF system checked
by an authorized HYUNDAI dealer.
• When there is a malfunction with
the emission control system. If you continue to drive with the
Malfunction Indicator Lamp (MIL)
In this case, we recommend that blinking for a long time, the DPF
you have the vehicle inspected by system can be damaged and fuel
an authorized HYUNDAI dealer. consumption can worsen.
NOTICE
- Malfunction Indicator Lamp
(MIL)
Driving with the Malfunction Indi-
cator Lamp (MIL) on may cause
damage to the emission control
systems which could effect driv-
ability and/or fuel economy.
5-49
Convenient features of your vehicle
5-50
05
NOTICE Low Fuel Level Warn-
- Engine Oil Pressure Warning ing Light
Light
• If the engine does not stop im-
mediately after the Engine Oil This warning light illuminates:
Pressure Warning Light is illu- When the fuel tank is nearly empty.
minated, severe damage could
result.
• If the warning light stays on If the fuel tank is nearly empty, add
while the engine is running, it in- fuel as soon as possible.
dicates that there may be seri-
ous engine damage or malfunc- NOTICE
tion. In this case,
- Low Fuel Level
1. Stop the vehicle as soon as it
is safe to do so. Driving with the Low Fuel Level
warning light on or with the fuel
2. Turn off the engine and check level below “E (Empty)” can cause
the oil level. If the oil level is the engine to misfire and damage
low, fill the engine oil to the the catalytic converter (if
proper level. equipped).
3. Start the engine again. If the
warning light stays on after
the engine is started, turn the Door Ajar Warning
engine off immediately. In this Light (for conventional
case, we recommend that you cluster)
have the vehicle inspected by
an authorized HYUNDAI deal- This warning light illuminates:
er.
When a door is not close securely.
5-51
Convenient features of your vehicle
Immobilizer Indicator
NOTICE Light (with smart key)
- Fuel Filter Warning Light (if equipped)
• When the Fuel Filter Warning
Light illuminates, engine power This indicator light illuminates for
(vehicle speed & idle speed) up to 30 seconds:
may decrease.
When the vehicle detects the smart
• If you keep driving with the key in the vehicle properly while the
warning light on, engine parts Engine Start/Stop button is ACC or
(injector, common rail, high ON.
pressure fuel pump) may be
- At this time, you can start the en-
damaged. If this occurs, we rec-
gine.
ommend that you have the vehi-
cle inspected by an authorized - The indicator light goes off after
HYUNDAI dealer as soon as starting the engine.
possible.
5-52
05
This indicator light blinks for a few Turn Signal Indicator
seconds: Light
When the smart key is not in the vehi-
cle.
- At this time, you can not start the This indicator light blinks:
engine. When you turn the turn signal light
on.
This indicator light illuminates for 2
seconds and goes off: If any of the following occurs, there
When the vehicle can not detect the may a malfunction with the turn signal
smart key which is in the vehicle while system. In this case, we recommend
the Engine Start/Stop button is ON. that you have the vehicle inspected
In this case, we recommend that you by an authorized HYUNDAI dealer.
have the vehicle inspected by an au- - The indicator light does not blink
thorized HYUNDAI dealer. but illuminates.
- The indicator light blinks more
This indicator light blinks: rapidly.
• When the battery of the smart key - The indicator light does not illumi-
is weak. nate at all.
- At this time, you can not start the
engine. However, you can start
the engine if you press the En-
gine Start/Stop button with the
smart key. (For more details, re-
fer to “Starting the Engine” in
chapter 5).
• When there is a malfunction with
the immobilizer system.
In this case, we recommend that
you have the vehicle inspected by
an authorized HYUNDAI dealer.
5-53
Convenient features of your vehicle
5-54
05
KEY OUT Indicator KEY Exhaust System (DPF)
Light (if equipped) Warning Light
OUT (for diesel engine,
if equipped)
When the Engine Start/Stop button is This warning light illuminates:
in the ACC or ON position, if any door
• When there is a malfunction with
is open, the system checks for the
the Diesel Particulate Filter (DPF)
smart key.
system.
When this warning light illuminates,
This indicator light blinks: it may turn off after driving the ve-
When the smart key is not in the vehi- hicle:
cle and any door is open with the igni- - at more than 60 km/h (37 mph), or
tion switch or Engine Start/Stop but-
- above 2nd gear with 1500 ~ 2500
ton in the ACC or ON position.
engine rpm for a certain time (for
- At this time, if you close all doors, about 25 minutes).
the chime will also sound for approx-
If this warning light blinks in spite of
imately 5 seconds.
the procedure (at this time LCD warn-
- The indicator will go off while the ve- ing message will be displayed), we
hicle is moving. recommend that you have the DPF
system checked by an authorized
HYUNDAI dealer.
NOTICE
If you continue to drive with the
DPF warning light blinking for a
long time, the DPF system can be
damaged and fuel consumption
can worsen.
5-55
Convenient features of your vehicle
5-56
05
• When one or more of your tires are LCD display messages
significantly underinflated (The lo- (if equipped)
cation of the underinflated tires are
displayed on the LCD display). Shift to “P” position
(for smart key system and duel
For more details, refer to clutch transmission)
“Tire Pressure Monitoring System
(TPMS)” in chapter 6. ٻType B
OQXI049127
This warning message illuminates if
the battery of the smart key is dis-
charged when the Engine Start/Stop
button is in the OFF position.
5-57
Convenient features of your vehicle
OHCR046117
OHCR046115
This warning message illuminates if This warning message illuminates if
the steering wheel does not unlock the steering wheel does not lock nor-
normally when the Engine Start/Stop mally when the Engine Start/Stop
button is pressed. button is in the OFF position.
Press the Engine Start/Stop button
while turning the steering wheel right Press clutch pedal to start en-
and left. gine (for smart key system and
manual transmission)
Steering wheel unlocked ٻType B
(for smart key system)
ٻType B
OHCR046119
This warning message illuminates if
the Engine Start/Stop button is in the
OHCR046116 ACC position twice by pressing the
This warning message illuminates if button repeatedly without depressing
the steering wheel does not lock the clutch pedal.
when the Engine Start/Stop button is Depress the clutch pedal to start the
in the OFF position. engine.
5-58
05
Press brake pedal to start en- Key not detected
gine (for smart key system duel (for smart key system)
clutch transmission) ٻType B
ٻType B
OIB047137-
OHCR046118
This warning message illuminates if
the smart key is not detected when
• This warning message illuminates you press the Engine Start/Stop but-
if the Engine Start/Stop button ton.
changes to the ACC position twice
by pressing the button repeatedly
without depressing the brake ped- Press start button again
al. (for smart key system)
• It means that you should depress ٻType B
the brake pedal to start the engine.
OHCR046122
This warning message illuminates if
you cannot operate the Engine Start/
Stop button when there is a problem
with the Engine Start/Stop button
system.
OIB047138-
Start the engine by pressing the En-
This warning message illuminates if gine Start/ Stop button once more.
the smart key is not in the vehicle If the warning illuminates each time
when you press the Engine Start/ you press the Engine Start/Stop but-
Stop button. ton, we recommend that you have the
Always have the smart key with you. vehicle inspected by an authorized
HYUNDAI dealer.
5-59
Convenient features of your vehicle
Press “START” button with key Shift to “P” or “N” to start en-
(for smart key system) gine (for smart key system and
ٻType B
dual clutch transmission)
ٻType B
OQXI049126
OHCR046125
This warning message illuminates if
you press the Engine Start/Stop but-
ton while the warning message “Key • This warning message illuminates
not detected” is Illuminated. if you try to start the engine with
the shift lever not in the P (Park) or
At this time, the immobilizer indicator N (Neutral) position.
light will blink.
OHCR046124
• This warning message illuminates
if the brake switch fuse is discon-
nected.
• It means that you should replace
the fuse with a new one. If that is
not possible, you can start the en-
gine by pressing the Engine Start/
Stop button for 10 seconds in the
ACC position.
5-60
05
Door Open Tailgate Open
ٻType B ٻType B
OIB047144 OIB047145
This indicator displays which door is This indicator displays when the tail-
open. gate is open.
OIB047146
This indicator displays when the hood
is open.
5-61
Convenient features of your vehicle
OHCR046133
OIB044150 This warning message illuminates
This warning message illuminates if with a warning chime when the en-
you start the engine when the steer- gine coolant temperature is above
ing wheel is turned 90 degrees to the 120°C (248°F). This means that the
left or right. engine is overheated and may be
Turn the steering wheel and make damaged.
the angle of the steering wheel be
less than 30 degrees.
Low Fuel
ٻType B
OIB044148
This warning message illuminates if
the fuel tank is nearly empty.
- When the low fuel level warning
light is illuminates.
- When the trip computer displays
“--- km(or mile)” as distance to
empty.
5-62
05
/&'',63/$<ǣ&/867(57<3(%Ǥ
LCD display control (if equipped)
OQXI049029
The LCD display modes can be changed by using the control buttons.
(1) : MODE button for changing modes
(2) , : MOVE switch for changing items
(3) OK : SELECT/RESET button for setting or resetting the selected item
5-63
Convenient features of your vehicle
LCD modes
Modes Symbol Explanation
This mode displays driving infor-
mation like the tripmeter, fuel
Trip Computer economy, and so on.
F.or more details, refer to “Trip
Computer” in this chapter.
This mode informs of the service
Information or or interval (mileage or days) and
warning messages.
For controlling the LCD modes, refer to “LCD Display Control” in this chapter.
5-64
05
Cannot edit settings while driv- Quick guide (Help, if equipped)
ing If you press and hold the OK button in
the User Settings Mode, explanation
ٻType A
about the selected item is displayed
in the cluster.
OIB044163
OHCR046136
This mode displays driving informa-
tion like the tripmeter, fuel economy,
and so on.
5-65
Convenient features of your vehicle
Service Interval
ٻType B
OHCR046141
Service required
OHCR046139 If you do not have your vehicle ser-
Service in viced according to the already in-
It calculates and displays when you putted service interval, “Service re-
need a scheduled maintenance ser- quired” message is displayed for
vice (mileage or days). several seconds each time you set
the ignition switch or Engine Start/
If the remaining mileage or time Stop button to the ON position.
reaches 1,500 km (900 miles) or 30
days, “Service in” message is dis- To reset the service interval to the
played for several seconds each time mileage and days you inputted be-
you set the ignition switch or Engine fore:
Start/Stop button to the ON position. - Press the OK button for more than 1
second.
For the setting of the service inter-
val, refer to “User Settings Mode”
of the LCD display. i Information
If any of the following conditions
occurs, the mileage and days may
be incorrect.
- The battery cable is disconnect-
ed.
- The fuse switch is turned off.
- The battery is discharged.
Warning Message
If one of followings occurs, warning
messages will be displayed on the in-
formation mode for several seconds.
- Low fuel etc.
5-66
05
User settings mode (Cluster Type B)
In this mode, you can change setting of the instrument cluster, doors, lamps,
and so on.
Door
Items Explanation
• Disable : The auto door lock operation will be deactivated.
• Enable on Speed : All doors will be automatically locked when the
vehicle speed exceeds 9.3 mph (15km/h).
Auto Lock
• Enable on Shift : All doors will be automatically locked if the dual
clutch transmission shift lever is shifted from the P (Park) position
to the R (Reverse), N (Neutral), or D (Drive) position.
• Disable : The auto door unlock operation will be canceled.
• Vehicle Off: All doors will be automatically unlocked when the ig-
nition key is removed from the ignition switch or the Engine Star/
Auto Unlock Stop button is set to the OFF position.
• On Shift to P: All doors will be automatically unlocked if the dual
clutch transmission shift lever is shifted to the P (Park) position.
Light
Items Explanation
• Off: The one touch turn signal function will be deactivated.
One Touch • 3, 5, 7 Flashes : The lane change signals will blink 3, 5, or 7 times
Turn Signal when the turn signal lever is moved slightly.
For more details, refer to “Light” in this chapter.
• Off: The headlamp delay function will be deactivated.
Head Lamp De- • On: The head lamp delay function will be activated.
lay
For more details, refer to “Light” in this chapter.
5-67
Convenient features of your vehicle
Service interval
Items Explanation
In this mode, you can activate the service interval function with mile-
age (km or mi.) and period (months).
Service Interval • Off : The service interval function will be deactivated.
• On :You can set the service interval (mileage and months).
Other features
Items Explanation
• Off : The average fuel economy will not reset automatically when-
ever refueling.
• After Ignition : The average fuel economy will reset automatically
Fuel Economy whenever it has passed 4 hours after turning OFF the engine.
Auto Reset
• After Refueling : The average fuel economy will reset automatical-
ly when refueling.
For more details, refer to “Trip Computer” in this chapter.
Fuel Economy Choose the fuel economy unit. (Km/L, L/100km)
Unit
Temperature Choose the temperature unit. (°C,°F)
Unit
Language
Items Explanation
Language Choose the language.
5-68
05
75,3&20387(5
Tripmeter/Trip computer Press the trip mode/reset button for
less than 1 second to select any
mode as follows:
Tripmeter A
Tripmeter B
Distance to empty*
OQXI049030
Service Reminder*
* if equipped
5-69
Convenient features of your vehicle
ٻType A
OQXI049117 OQXI049119
ٻType B
Distance to empty (if equipped)
(km or mi.)
This mode indicates the estimated
distance to empty based on the cur-
rent fuel in the fuel tank and the
amount of fuel delivered to the en-
gine. When the remaining distance is
below 50 km (30 miles), “---” will be
displayed.
OQXI049118 The meter’s working range is from 50
to 999 km (30 to 615 miles).
Tripmeter (km or mi.)
A : Tripmeter A
B : Tripmeter B
5-70
05
OQXI049120 OQXI049121
5-71
Convenient features of your vehicle
OQXI049122 OQXI049123
5-72
05
Service reminder Cluster Type B
The trip computer is a microcomput-
er-controlled driver information sys-
tem that displays information related
to driving.
i Information
Some driving information stored in the
trip computer (for example Average
Vehicle Speed) resets if the battery is
OQXI049124
disconnected.
This mode displays the service inter-
val (mileage).
Trip modes
Digital Speedometer
Fuel Economy
• Average Fuel Economy
• Instant Fuel Economy
Accumulated Info
• Tripmeter
• Average Fuel Economy
OQXI049125
• Elapsed Time
This message shows the speed of
the vehicle (km/h, MPH).
Drive Info
• Tripmeter
• Average Fuel Economy
• Elapsed Time
Dital Speedometer
5-73
Convenient features of your vehicle
i Information
• If the vehicle is not on level ground
or the battery power has been inter-
rupted, the distance to empty func-
tion may not operate correctly.
• The distance to empty may differ
from the actual driving distance as
it is an estimate of the available
driving distance.
OQXI049029
• The trip computer may not register
To change the trip mode, toggle the “, additional fuel if less than 6 liters
” switch on the steering wheel. (1.6 gallon) of fuel are added to the
vehicle.
Fuel economy • The fuel economy and distance to
empty may vary significantly based
on driving conditions, driving hab-
its, and condition of the vehicle.
5-74
05
Automatic reset Accumulated Info display
To automatically reset the average
fuel economy after refueling, select
the “Auto Reset” mode in User Set-
tings menu on the LCD display.
- After Ignition: The average fuel
economy will reset automatically
whenever it has passed 4 hours af-
ter turning OFF the engine.
- After Refueling: The average fuel
economy will reset automatically
when driving speed exceeds 1 OQXI049029
km/h, after adding 6 liters (1.6 gal-
lons) of fuel or more. This display shows the accumulated
trip distance (1), the average fuel
economy (2), and the total driving
i Information time (3).
The average fuel economy may be in- The information is calculated starting
accurate, when the vehicle drives from the last reset.
shorter than 300 meters (0.19 miles) To manually reset the information,
after turning ON the Engine Start/ press and hold the OK button when
Stop button. viewing the Accumulated driving info.
The trip distance, the average fuel
economy, and total driving time will
Instant Fuel Economy (3) reset simultaneously.
• This mode displays the instanta-
neous fuel economy while driving
when the vehicle speed is greater The accumulated driving information
than 10 km/h (6.2 mph). will continue to be counted while the
engine is still running (for example,
- Fuel economy range: 0~30
when the vehicle is in traffic or
L/100km, km/L or 0~50 MPG
stopped at a stop light.)
i Information
The vehicle must be driven for a mini-
mum of 300 meters (0.19 miles) since
the last ignition key cycle before the
average fuel economy will be recalcu-
lated.
5-75
Convenient features of your vehicle
OQXI049116 OHCR046137
This display shows the trip distance This message shows the speed of
(1), the average fuel economy (2), the vehicle (km/h, MPH).
and the total driving time (3).
The information is calculated for each
ignition cycle. The driving information
data gets initialized, when it has
passed 4 hours after turning OFF the
engine. In other words, the last driv-
ing information is available 4 hours
after you have turned on the engine.
i Information
The vehicle must be driven for a mini-
mum of 300 meters (0.19 miles) since
the last ignition key cycle before the
average fuel economy will be recalcu-
lated.
5-76
05
LIGHT
Exterior lights
Lighting control
OQXI049033
OQXI049032
Headlight position ( )
When the light switch is in the head
light position, the headlights, license
plate light and instrument panel lights
are turned ON.
i Information
The ignition switch must be in the ON
position to turn on the headlights.
5-77
Convenient features of your vehicle
OQXI049034 OQXI049035
5-78
05
One-touch lane change function
To activate an One-Touch Lane
Change function, move the turn sig-
nal lever slightly and then release it.
The lane change signals will blink 3, 5
or 7 times.
You can activate/deactivate the One
Touch Turn Signal function or choose
the number of blinking (3, 5, or 7)
OQXI049036
from the User Settings Mode on the
LCD display.
To flash the high beam headlights, For more details, refer to “LCD Dis-
pull the lever towards you, then re- play” in this chapter.
lease the lever. The high beams will
remain ON as long as you hold the
lever towards you. NOTICE
If the turn signal indicator stays on
Turn signals and lane change and does not flash, or if it flashes
signals abnormally, a bulb may be burned
out or have a poor electrical con-
nection in the circuit. The bulb may
require replacement.
OQXI049037
5-79
Convenient features of your vehicle
NOTICE
When in operation, the fog lights
consume large amounts of vehicle
electrical power. Only use the fog
lights when visibility is poor.
5-80
05
Headlight delay function Headlight leveling device
(if equipped) (if equipped)
If the key is removed from the ignition
switch or placed in the ACC or LOCK/
OFF position with the headlights ON,
the headlights (and/or parking lights)
remain on for about 5 minutes. How-
ever, with the engine off if the driver’s
door is opened and closed, the head-
lights (and/or parking lights) are
turned off after 15 seconds.
The headlights (and/or parking lights)
can be turned off by pressing the lock OQXI049039
button on the remote key (or smart To adjust the headlight beam level
key) twice or turning the light switch according to the number of the pas-
to the OFF or AUTO position. Howev- sengers and loading weight in the
er, if you turn the light switch to the luggage area, turn the beam leveling
AUTO position when it is dark out- switch.
side, the headlights will not be turned The higher the number of the switch
off. position, the lower the headlight
beam level. Always keep the head-
NOTICE light beam at the proper leveling posi-
tion, or headlights may dazzle other
If the driver gets out of the vehicle road users.
through other doors (except driv-
Listed below are the examples of
er’s door), the battery saver func-
proper switch settings. For loading
tion does not operate and the
conditions other than those listed be-
headlight delay function does not
low, adjust the switch position so that
turn off automatically. Therefore, It
the beam level may be the nearest as
causes the battery to be dis-
the condition obtained according to
charged. In this case, make sure to
the list.
turn off the lamp before getting out
of the vehicle. Loading condition Switch position
Driver only 0
5-81
Convenient features of your vehicle
5-82
05
Front lamps (If equipped) : The front room lamps come
on when the front or rear
doors are opened if the en-
gine is running or not. When
doors are unlocked by the re-
mote key or smart key, the
front lamps come on for ap-
proximately 15 seconds as
long as any door is not
opened. The front room
lamps go out gradually after
OQXI049040 approximately 15 seconds if
(1) Front Map Lamp the door is closed. However,
if the ignition switch is in the
(2) Front Room Lamp ON position or all doors are
locked, the front lamps will
Front Map Lamp: turn off immediately. If a door
Press either the right or left lens to is opened with the ignition
turn the map lamp on or off. This light switch in the ACC position or
produces a spot beam for convenient the LOCK/OFF position, the
use as a map lamp at night or as a front lamps stay on for about
personal lamp for the driver and the 20 minutes. However, if a
front passenger. door is opened with the igni-
tion switch in the ON position,
the lamps stays on continu-
Front Room Lamp: ously.
The Front Room Lamp Switch acti- : With the Front Room Lamp in
vates the front lamps when the switch this position, the front room
is pressed in either of the three posi- lamps remain on at all times.
tions indicated below: : With the Front Room Lamp in
this position the front room
lamps remain off at all times.
i Information
When the map lamp (1) is turned ON
by pressing the lens, the map lamp will
not turn off even if the front room
lamp switch is in the OFF position.
5-83
Convenient features of your vehicle
NOTICE
Do not leave the lamp switches on for
an extended period of time when the
OQXI049041 engine is turned off.
Rear Door Lamp Switch:
The Rear Room Lamp Switch acti- Luggage room lamp
vates the rear room lamp when the (if equipped)
switch is pressed in either of the three
positions indicated below
5-84
05
:,3(56$1':$6+(56
ٻFront
• Type A
A : Wiper speed control
• MIST – Single wipe
• OFF – Off
• INT – Intermittent wipe
• LO – Low wiper speed
• HI – High wiper speed
• Type B
B : Intermittent wipe time
adjustment
ٻRear
D : Rear wiper/washer control
(if equipped)
• ON – Continuous wipe
• OFF - Off
OQXI049043/OQXI049044/OQXI049045
5-85
Convenient features of your vehicle
5-86
05
NOTICE Rear window wiper and washer
• To prevent possible damage to switch (if equipped)
the washer pump, do not oper-
ate the washer when the fluid
reservoir is empty.
• To prevent possible damage to
the wipers or windshield, do not
operate the wipers when the
windshield is dry.
• To prevent damage to the wiper
arms and other components, do
not attempt to move the wipers
OQXI049047
manually.
The rear window wiper and washer
• To prevent possible damage to
switch is located at the end of the
the wipers and washer system,
wiper and washer switch lever. Turn
use anti-freezing washer fluids
the switch to the desired position to
in the winter season or cold
operate the rear wiper and washer.
weather.
ON – Continuous wipe
OFF – Off
OQXI049048
5-87
Convenient features of your vehicle
'5,9(5$66,676<67(0
Rear view monitor WARNING
(if equipped)
The Rear View Monitor is not a
safety device. It only serves to as-
sist the driver in identifying ob-
jects directly behind the middle of
the vehicle. The camera does NOT
cover the complete area behind
the vehicle.
WARNING
OQXI049049 • Never rely solely on the rear
camera display when back-
ing-up.
• ALWAYS look around your
vehicle to make sure there are
no objects or obstacles before
moving the vehicle in any direc-
tion to prevent a collision.
• Always pay close attention when
the vehicle is driven close to ob-
OQXI049050
jects, particularly pedestrians,
and especially children.
The Rear View Camera will activate
when the ignition switch is in the ON
position and the shift lever is in the R
(Reverse) position.
This is a supplemental system that
shows behind the vehicle through the
audio or indotainment system screen
while backing-up.
5-88
05
NOTICE Driving Rear view Monitor (DRM)
(if equipped)
• Do not spray the camera or its
surrounding area directly with a
high pressure washer. Shock
applied from high pressure wa-
ter may cause the device to not
operate normally.
• Do not use any cleanser con-
taining acid or alkaline deter-
gents when cleaning the lens.
Use only a mild soap or neutral
detergent, and rinse thoroughly OQXI049072
with water.
You may check the rear view through
the screen while driving.
i Information
Always keep the camera lens clean. The system is activated when:
The camera may not work normally if
• Press the custom button (1) when
the lens is covered with dirt, water or
you set the custom button in the
snow.
infotainment system as a rearview
monitor mode.
• Touch the Rear view button on the
infotainment system screen (All
menus Rear view)
5-89
Convenient features of your vehicle
5-90
05
NOTICE Non-operational conditions of
• If an object is in between sen- Parking Distance Warning
sors or close to a sensor, the (Reverse) System
displayed indicator may differ The Parking Distance Warning
from the above illustration. (Reverse) System may not operate
• Do not wash the vehicle’s sen- normally when:
sor with high pressure water. • Moisture is frozen to the sensor.
• When you shift into the R (Re- • The sensor is covered or stained
verse) position and one or more with foreign material, such as snow
of the below situation occurs, or water, or the sensor cover is
this may indicate a malfunction blocked.
with the parking assist system.
• You don’t hear an audible warn- There is a possibility of a parking
ing sound or the buzzer sounds assist system malfunction when:
intermittently.
• Driving on uneven road surfaces
• is displayed. (if equipped) such as unpaved roads, gravel,
bumps, or gradient.
If this occurs, we recommend • Objects generating excessive
that the system be checked by noise such as vehicle horns, loud
an authorized HYUNDAI dealer. motorcycle engines, or truck air
brakes can interfere with the sen-
sor.
• Heavy rain or water spray is pres-
ent.
• Wireless transmitters or mobile
phones are present near the sen-
sor.
• The sensor is covered with snow.
• Any non-factory equipment or ac-
cessories have been installed, or if
the vehicle bumper height or sen-
sor installation has been modified.
5-91
Convenient features of your vehicle
i Information
The system may not recognize objects
less than 30 cm (12 in.) from the sensor,
or it may sense an incorrect distance.
NOTICE
Do not push, scratch or strike the
sensor with any hard objects that
could damage the surface of the
sensor. Sensor damage could oc-
cur.
WARNING
Your new vehicle warranty does
not cover any accidents or dam-
age to the vehicle or injuries to its
occupants due to a Parking Dis-
tance Warning (Reverse) System
malfunction. Always drive safely
and cautiously.
5-92
05
&/,0$7(&21752/6<67(0
Defroster To activate the rear window defrost-
NOTICE er, press the rear window defroster
button located in the climate control
To prevent damage to the conduc- system. The indicator on the rear win-
tors bonded to the inside surface dow defroster button illuminates
of the rear window, never use when the defroster is ON.
sharp instruments or window
To turn off the defroster, press the
cleaners containing abrasives to
rear window defroster button again.
clean the window.
If you want to defrost and defog
the front windshield, refer to i Information
“Windshield defrosting and defog-
ging” in this section. • If there is heavy accumulation of
snow on the rear window, brush it
off before operating the rear de-
Rear window defroster froster.
(if equipped) • The rear window defroster auto-
ٻManual Climate Control System matically turns off after approxi-
mately 20 minutes or when the igni-
tion switch is turned off.
OQXI049302
OQXI049303
5-93
Convenient features of your vehicle
OQXI049300
5-94
05
Heating and air conditioning
OQXI049304
5-95
Convenient features of your vehicle
Mode selection
Floor/Defrost-Level (A, C, D)
OQXI049305
Defrost-Level (A, D)
The mode selection knob controls the
direction of the air flow through the
ventilation system.
Most of the air flow is directed to the
Air can be directed to the floor, dash- windshield with a small amount of air
board outlets, or windshield. Five directed to the side vents.
symbols are used to represent Face,
Bi-Level, Floor, Floor-Defrost and
Defrost air position.
Face-Level (B, D, E)
Bi-Level (B, C, D, E)
Floor-Level (A, C, D)
5-96
05
ٻFront Temperature control
OQXI049306
ٻRear OQXI049308
OQXI049307
5-97
Convenient features of your vehicle
5-98
05
Fan speed control System operation
Ventilation
1. Select the Face Level mode.
2. Set the air intake control to the out-
side (fresh) air position.
3. Set the temperature control to the
desired position.
4. Set the fan speed control to the de-
sired speed.
OQXI049310
Heating
Turn the knob to the right to increase
the fan speed and airflow. Turn the 1. Select the Floor Level mode.
knob to the left to decrease fan speed 2. Set the air intake control to the out-
and airflow. side (fresh) air position.
3. Set the temperature control to the
Air conditioning (A/C) desired position.
4. Set the fan speed control to the de-
sired speed.
5. If dehumidified heating is desired,
turn the air conditioning system (if
equipped) on.
If the windshield fogs up, select the
Floor & Defrost mode or select
the Front Defroster mode.
OQXI049311
5-99
Convenient features of your vehicle
5-100
05
System maintenance Checking the amount of air con-
ditioner refrigerant and com-
pressor lubricant
Outside air
When the amount of refrigerant is
Recirculated low, the performance of the air condi-
air tioning is reduced. Overfilling also
has a bad influence on the air condi-
tioning system.
Therefore, if abnormal operation is
Blower found, we recommend that the sys-
Climate control Evaporator Heater core tem be inspected by an authorized
air filter core HYUNDAI dealer.
1LDA5047
5-101
Convenient features of your vehicle
OQXI049301
5-102
05
Automatic heating and air condi- To turn the automatic operation off,
tioning select any button of the following:
The Automatic Climate Control Sys- - Mode selection button
tem is controlled by setting the de- - Front windshield defrost button
sired temperature. (Press the button one more time to
deselect the front windshield de-
froster function.
- Fan speed control button
The selected function will be con-
trolled manually while other functions
operate automatically.
For your convenience and to improve
the effectiveness of the climate con-
trol, use the AUTO button and set the
OQXI049312 temperature to 23°C (73°F).
1. Press the AUTO button.
The modes, fan speeds, air intake
and air-conditioning will be controlled
automatically by the temperature set-
ting you select.
OQXI049318
5-103
Convenient features of your vehicle
5-104
05
OQXI049304
5-105
Convenient features of your vehicle
Mode selection
OQXI049316
Face-Level (B, D, E)
Floor-Level (A, C, D)
Defrost-Level (A, D)
5-106
05
ٻFront Temperature control
OQXI049306
ٻRear OQXI049318
5-107
Convenient features of your vehicle
i Information
Prolonged use of the air conditioning
with the recirculated air position se-
lected will result in excessively dry air
in the passenger compartment.
5-108
05
Fan speed control OFF mode
OQXI049313 OQXI049320
Turn the knob to the right increase Push the OFF button to turn off the
the fan speed and air flow. Turn the climate control system. You can still
knob to the left to decrease fan speed operate the mode and air intake but-
and air flow. tons with the ignition switch in the ON
position.
Air conditioning
System operation
Ventilation
1. Select the Face Level mode.
2. Set the air intake control to the out-
side (fresh) mode.
3. Set the temperature control to the
desired position.
4. Set the fan speed control to the de-
sired speed.
OQXI049319
5-109
Convenient features of your vehicle
5-110
05
System maintenance Checking the amount of air
conditioner refrigerant and com-
Outside air pressor lubricant
Recirculated
air When the amount of refrigerant is
low, the performance of the air condi-
tioning is reduced. Overfilling also
has a bad influence on the air condi-
Blower
tioning system.
Climate control Evaporator Heater core Therefore, if abnormal operation is
air filter core
1LDA5047
found, we recommend that the sys-
tem be inspected by an authorized
Climate control air filter HYUNDAI dealer.
This filter is installed behind the glove
box. It filters the dust or other pollut-
ants that enter the vehicle through i Information
the heating and air conditioning sys-
tem. It is important that the correct type
and amount of oil and refrigerant is
We recommend the climate control used. Otherwise, damage to the com-
air filter be cleaned according to the pressor and abnormal system opera-
maintenance schedule. If the car is tion may occur.
being driven in severe conditions
such as dusty or rough roads, more
frequent air conditioner filter inspec- WARNING
tions and cleaning are required.
If the air flow rate suddenly decreas- Because the refrigerant is
es, we recommend the system be at very high pressure, the
checked at an authorized HYUNDAI air conditioning system
dealer. should only be serviced
by trained and certified techni-
cians. It is important that the cor-
rect type and amount of oil and re-
frigerant is used, otherwise
damage to the vehicle and person-
al injury may occur.
5-111
Convenient features of your vehicle
5-112
05
Automatic climate control sys-
tem
To defog inside windshield
OQXI049322
5-113
Convenient features of your vehicle
OQXI049324 OQXI049325
5-114
05
6725$*(&203$570(17
WARNING Center console storage
(if equipped)
Flammable materials
Do not store cigarette lighters,
propane cylinders, or other flam-
mable/explosive materials in the
vehicle. These items may catch
fire and/or explode if the vehicle is
exposed to hot temperatures for
extended periods.
WARNING OQXI049052
ALWAYS keep the storage com- To open the center console storage,
partment covers closed securely pull up the lever.
while driving. Items inside your ve-
hicle are moving as fast as the ve- Sliding armrest (if equipped)
hicle. If you have to stop or turn
quickly, or if there is a crash, the
items may fly out of the compart-
ment and may cause an injury if
they strike the driver or a passen-
ger.
NOTICE
To avoid possible theft, do not
leave valuables in the storage
OQXI049053
compartment.
To move the armrest forward:
Grab the front portion of the armrest
(1) then pull it forward.
WARNING
Do not grab the front portion of the
armrest (1) when moving the arm-
rest rearward. You may hurt your
fingers.
5-115
Convenient features of your vehicle
OQXI049054 OQXI049055
To open the glove box, pull the lever You can keep beverage cans or other
and the glove box will automatically items cool in the glove box.
open. Close the glove box after use. 1. Turn on the air conditioning.
2. Turn the open/close switch (1) of
WARNING the vent installed in the glove box
to the open position.
ALWAYS close the glove box door 3. When the cool box is not used, turn
after use. the switch (1) to the closed posi-
An open glove box door can cause tion.
serious injury to the passenger in
an accident, even if the passenger
is wearing a seat belt. WARNING
Do not put perishable food in the
cool box because it may not main-
tain the necessary consistent tem-
perature to keep the food fresh.
i Information
• If the vent is blocked by items in the
coolbox, cooling will be reduced.
• If the climate control system tem-
perature control is in the warm or
hot position, warm or hot air will
flow into the glove box.
5-116
05
Luggage box (if equipped)
OIB047035
5-117
Convenient features of your vehicle
INTERIOR FEATURES
Clock (if equipped) WARNING
WARNING
• Avoid abrupt starting and brak-
Do not adjust the clock while driv- ing when the cup holder is in
ing. You may lose your steering use to prevent spilling your
control and cause severe personal drink. If hot liquid spills, you
injury or accidents. could be burned. Such a burn to
the driver could cause loss of
vehicle control resulting in an
Cup holder accident.
Front • Do not place uncovered or unse-
cured cups, bottles, cans, etc.,
in the cup holder containing hot
liquid while the vehicle is in mo-
tion. Injuries may result in the
event of sudden stop or colli-
sion.
• Only use soft cups in the cup
holders. Hard objects can injure
you in an accident.
OQXI049056
NOTICE
• Keep your drinks sealed while
driving to prevent spilling your
drink. If liquid spills, it may get
into the vehicle’s electrical/elec-
tronic system and damage elec-
trical/electronic parts.
• When cleaning spilled liquids,
OQXI049057 do not dry the cup holder at high
Pull the armrest down to use the cup temperature. This may damage
holders. the cup holder.
5-118
05
Sunvisor Power outlet
ٻDriver’s side ٻFront
· Type A
OIB044027 OQXI049058
OIB044028 OQXI049059
WARNING
For your safety, do not block your
view when using the sunvisor. OQXI049060
5-119
Convenient features of your vehicle
WARNING NOTICE
To prevent damage to the Power
Avoid electrical shocks. Do not outlet:
place your fingers or foreign ob-
• Use the power outlet only when
jects (pin, etc.) into a power outlet
the engine is running and re-
or touch the power outlet with a
move the accessory plug after
wet hand.
use. Using the accessory plug
for prolonged periods of time
with the engine off could cause
the battery to discharge.
• Only use 12V electric accesso-
ries which are less than 180W
(Watt) in electric capacity.
• Adjust the air-conditioner or
heater to the lowest operating
level when using the power out-
let.
• Close the cover when not in use.
• Some electronic devices can
cause electronic interference
when plugged into a vehicle’s
power outlet. These devices
may cause excessive audio stat-
ic and malfunctions in other
electronic systems or devices
used in your vehicle.
• Push the plug in as far as it will
go. If good contact is not made,
the plug may overheat or the in-
ternal temperature fuse may
open.
• Plug in battery equipped electri-
cal/electronic devices with re-
verse current protection. The
current from the battery may
flow into the vehicle’s electrical/
electronic system and cause
system malfunction.
5-120
05
USB charger (if equipped) Floor mat anchor(s)
(if equipped)
OQXI049061
5-121
Convenient features of your vehicle
WARNING WARNING
The following must be observed
when installing ANY floor mat to
the vehicle.
• Ensure that the floor mats are
securely attached to the vehi-
cle’s floor mat anchor(s) before
driving the vehicle.
• Do not use ANY floor mat that
cannot be firmly attached to the
OGSB047265L vehicle’s floor mat anchors.
Do not hang other objects such as • Do not stack floor mats on top of
hangers or hard objects except one another (e.g. all-weather
clothes. Also, do not put heavy, rubber mat on top of a carpeted
sharp or breakable objects in the floor mat). Only a single floor
clothes pockets. In an accident or mat should be installed in each
when the curtain air bag is inflated, position.
it may cause vehicle damage or IMPORTANT - Your vehicle was
personal injury. manufactured with driver’s side
floor mat anchors that are de-
signed to securely hold the floor
mat in place. To avoid any interfer-
ence with pedal operation, HYUN-
DAI recommends that the HYUND-
AI floor mat designed for use in
your vehicle be installed.
5-122
05
Cargo area cover (if equipped)
OQXI049062
WARNING
• Do not place objects on the car-
go area cover. Such objects may
be thrown about inside the vehi-
cle and possibly injure vehicle
occupants during an accident or
braking.
• Never allow anyone to ride in the
luggage compartment. It is de-
signed for luggage only.
NOTICE
Do not put luggage on the cover
since it may be damaged or mal-
formed.
5-123
Convenient features of your vehicle
EXTERIOR FEATURES
Roof rack (if equipped) WARNING
• The following specification is
the maximum weight that can be
loaded onto the roof rack. Dis-
tribute the load as evenly as pos-
sible onto the roof rack and se-
cure the load firmly.
Loading cargo or luggage in ex-
cess of the specified weight limit
on the roof rack may damage
OQXI049063 your vehicle.
If the vehicle has a roof rack, you can
load cargo on top of your vehicle. ROOF 70 kg (154 lbs.)
RACK EVENLY DISTRIBUTED
5-124
6. Infotainment System
INFOTAINMENT SYSTEM
NOTICE Antenna
• If you install an aftermarket HID ٻType A
head lamp, your vehicle’s audio
and electronic device may mal-
function.
• Prevent chemicals such as per-
fume, cosmetic oil, sun cream,
hand cleaner, and air freshener
from contacting the interior
parts because they may cause
damage, button struck issues or OQXI049065
discoloration.
ٻType B
OQXI049066
ٻType C
OQXI049064
Ã
iPod® is a trademark of Apple Inc.
6-2
06
Type C Steering wheel audio control
The shark fin antenna receives trans- (if equipped)
mitted data. (for example: AM/FM, ٻType A
and DRM)
NOTICE
• Before entering a place with a
low height clearance, be sure
that the antenna is removed.
• Be sure to remove the antenna
before washing the vehicle in an
automatic car wash or it may be OQXI049068
damaged. ٻType B
• When reinstalling your antenna,
it is important that it is fully
tightened and adjusted to the
upright position to ensure prop-
er reception. But it could be re-
moved when parking the vehi-
cle.
NOTICE OQXI049069
i Information
Some models do not have audio (plas- OQXI049070
tic blanking cover) system, and will not
supply radio main cable. Thus if you The steering wheel audio control but-
want to insert Aftermarket audio or ton is installed to promote safe driv-
OEM audio to listen radio broadcast- ing.
ing service, we recommend to use the
feeder cable available with an autho-
NOTICE
rized HYUNDAI dealer.
Do not operate audio remote con-
trol buttons simultaneously.
6-3
Infotainment System
RADIO mode
It will function as the PRESET STA-
TION select buttons.
MEDIA mode
It will function as the TRACK UP/
DOWN button.
MODE (3)
Press t he MODE button to toggle be-
tween available Media sources like
Radio, USB, iPod, BT Audio, AUX*
(Auxiliary).
* : if equipped
6-4
06
Bluetooth® Wireless Technology How vehicle audio works
hands-free (if equipped) FM reception
JBM001
6-5
Infotainment System
FM reception
JBM002
JBM003
6-6
06
FM reception
WARNING
Do not use a cellular phone while
driving. Stop at a safe location to
use a cellular phone.
iPod®
iPod® is a registered trademark of Ap-
ple Inc.
OJF045311L
NOTICE
When using a communication sys-
tem such as a cellular phone or a
radio set inside the vehicle, a sep-
arate external antenna must be fit-
ted. When a cellular phone or a ra-
dio set is used with an internal
antenna alone, it may interfere with
the vehicle’s electrical system and
adversely affect safe operation of
the vehicle.
6-7
Infotainment System
$8',2ǣ:,7+287728&+6&5((1Ǥ
System layout – control panel
ٻType A
à The actual features in the car may differ from the illustration.
6-8
06
ٻType A
à The actual features in the car may differ from the illustration.
6-9
Infotainment System
ٻType B
à The actual features in the car may differ from the illustration.
6-10
06
ٻType B
à The actual features in the car may differ from the illustration.
6-11
Infotainment System
6-13
Infotainment System
6-14
06
Turning the display on or off Numberless items
To prevent glare, you can turn off the Turn the [TUNE] knob to choose the
screen. The screen can be turned off desired item, and then press the knob
only while the system is on. to select the item.
1. On the control panel, press the
[MENU/CLOCK] button.
2. When the option selection window
displays, turn the [TUNE] knob to
select Display off, and then press
the knob.
• To turn the screen back on,
press any of the control panel
buttons.
6-15
Infotainment System
5$',2
Turning on the radio - Equaliser: Adjust the output
1. On the control panel, press the level for each sound tone mode.
[RADIO] / [AUDIO] button. - Sound Experience: Select the
2. When the mode selection window location where sound is focused
displays, turn the [TUNE] knob to in the vehicle between the driv-
select the desired radio mode and er’s seat and all other seats.
then press the knob. - Speed Dependent Vol.: Set the
volume to be adjusted automati-
cally according to your driving
FM/AM Mode speed. (if equipped)
NOTICE
• Depending on vehicle models or
specifications, available options
may vary.
• Depending on the system or am-
(1) Current radio mode
plifier specifications applied to
(2) Radio station information your vehicle, available options
(3) Preset list may vary.
6-16
06
- Display (Power Off): Set to dis- Scanning for available radio
play the clock when the system stations
power is off. You can listen to each radio station
• Language: You can change the for a few seconds to test the recep-
display language. tion and select the one you want.
1. From the radio screen, press the
Changing the radio mode [MENU/CLOCK] button on the
control panel.
1. On the control panel, press the
[RADIO] / [AUDIO] button. 2. When the option selection window
displays, turn the [TUNE] knob to
2. When the mode selection window select Scan, and then press the
displays, turn the [TUNE] knob to knob.
select the desired radio mode and
then press the knob. • The system searches for radio
stations with strong radio sig-
• Each time you press the [MODE] nals and plays each radio sta-
button on the steering wheel, tion for about five seconds.
the radio mode switches to FM
X AM in order. 3. When you find the radio station
you want to listen to, press the
[TUNE] knob.
NOTICE • You can continue listening to
When the Mode popup is not se- the selected station.
lected in [MENU/CLOCK] X Mode
Popup, press the [RADIO] /
[AUDIO] button on the control pan- Searching for radio stations
el to change the radio mode. To search for the previous or next
Each time you press the [RADIO] / available radio station, press the
[AUDIO] button on the control pan- [< SEEK] button / [TRACK >] button
el, the radio mode switches to FM on the control panel.
X AM in order. • You can also press and hold the
[< SEEK] button / [TRACK >] but-
ton to search for frequencies quick-
ly. When you release the button, a
radio station with a strong signal is
selected automatically.
If you know the exact frequency of
the radio station you want to listen to,
turn the [TUNE] knob on the control
panel to change the frequency.
6-17
Infotainment System
NOTICE
• You can save up to 12 radio sta-
tions in each mode.
• If a station is already saved to
the selected preset number, the
station will be replaced by the
station you are listening to.
6-18
06
0(',$3/$<(5
Using the media player • Do not connect a smartphone or
You can play music stored in various an MP3 device to the system via
media storage devices, such as USB multiple methods such as USB
storage devices, smartphones. and Bluetooth simultaneously.
Doing so may cause a distorted
1. Connect a device to the USB port noise or a system malfunction.
in your vehicle.
• When the equaliser function of
• Playback may start immediately the connected device and Equal-
depending on the device that iser settings of the system are
you connect to the system. both activated, the effects may
2. On the control panel, press the interfere with each other and
[MEDIA] / [AUDIO] button. may lead to sound degradation
3. When the mode selection window or distortion. Deactivate the de-
displays, turn the [TUNE] knob to vice’s equaliser function if pos-
select the desired mode and then sible.
press the knob. * : if equipped
6-19
Infotainment System
NOTICE
• Depending on vehicle models or
specifications, available options
may vary.
• Depending on the system or am-
plifier specifications applied to
(1) Current file number and total your vehicle, available options
number of files may vary.
(2) Playback time
(3) Information about the song cur- • Song Information: Select infor-
rently playing mation such as Folder/File or Art-
ist/Title/Album to display when
Press the [MENU/CLOCK] button on playing MP3 files.
the control panel to access the follow- • Mode Popup: Set to display
ing menu options: mode selection window when
• List: Access the file list. the [MEDIA] / [AUDIO] button is
pressed on the control panel.
• Folder List: Access the folder list.
• Lock Remote Controls: Even if
• Information: Display information
Bluetooth remote control applica-
about the song currently playing.
tion is connected, if Set Lock re-
• Sound Settings: You can change mote controls is enabled. System
the settings related to sounds, cannot be operated via smart
such as location where sound will phone application.
be concentrated and the output
• Date/Time: You can change the
level for each range.
date and time that are shown on
- Position: Select a location the system display.
where sound will be concentrat-
ed in the vehicle. Select Fader - Set Date: Set date to display on
or Balance, turn the [TUNE] the system display.
knob to select the desired posi- - Set Time: Set time to display on
tion, and then press the knob. the system display.
To set sound to be centred in - Time Format: Select to display
the vehicle, select Centre. time in the 12 hour format or the
- Equaliser: Adjust the output 24 hour format.
level for each sound tone mode.
- Display (Power Off): Set to dis-
- Sound Experience: Select the play the clock when the system
location where sound is focused power is off.
in the vehicle between the driv-
er’s seat and all other seats. • Language: You can change the
display language.
- Speed Dependent Vol.: Set the
volume to be adjusted automati-
cally according to your driving
speed. (if equipped)
6-20
06
Rewinding/Fast forwarding Playing repeatedly
On the control panel, press and hold On the control panel, press the
the [< SEEK] button / [TRACK >] but- [1 RPT] button. The repeat mode
ton. changes each time you press it. The
• You can also push and hold the corresponding mode icon will be dis-
Up/down lever on the steering played on the screen.
wheel.
Playing in random order
Restarting the current playback On the control panel, press the
On the control panel, press the [2 SHFL] button. The shuffle mode is
[< SEEK] button. activated or deactivated each time
you press it. When you activate the
• You can also push the Up lever on shuffle mode, the corresponding
the steering wheel. mode icon will be displayed on the
screen.
Playing the previous or next song
To play the previous song, press the NOTICE
[< SEEK] button twice on the control
panel. To play the next song, press Depending on the connected Blue-
the [TRACK >] button on the control tooth device or mobile phone, RPT
panel. & SHFL features may not be sup-
ported.
• You can also push the Up/down le-
ver on the steering wheel.
Searching folders
NOTICE 1. On the control panel, press the
[MENU/CLOCK] button.
Press the [MENU] button on the 2. When the option selection window
control panel to display the mode displays, turn the [TUNE] knob to
selection window, turn the [TUNE] select the Folder List and then
knob to find the desired song and press the knob.
press the knob to play the file.
3. Navigate to the desired folder in
the Folder List and then press the
[TUNE] knob.
• The first song in the selected
folder will be played.
6-21
Infotainment System
i Information NOTICE
• When connecting a USB storage
• Start the engine of your vehicle be- device, do not use an extension
fore connecting a USB device to cable. Connect it directly to the
your system. Starting the engine USB port. If you use a USB hub
with a USB device connected to the or an extension cable, the de-
system may damage the USB device. vice may not be recognized.
• Be careful of static electricity when • Fully insert a USB connector
connecting or disconnecting a USB into the USB port. Failure to do
device. A static discharge may cause so may cause a communication
a system malfunction. error.
• Be careful not to let your body or ex- • When you disconnect a USB
ternal objects contact the USB port. storage device, a distorted noise
Doing so may cause an accident or a may occur.
system malfunction. • The system can play only files
• Do not connect and disconnect a encoded in a standard format.
USB connector repeatedly in a short • The following types of USB de-
time. Doing so may cause an error in vices may not be recognised or
the device or a system malfunction. work correctly:
• Do not use a USB device for purpos- - Encrypted MP3 players
es other than playing files. Using
USB accessories for charging or - USB devices not recognised
heating may cause poor perfor- as removable disks
mance or a system malfunction. • A USB device may not be rec-
ognised depending on its condi-
tion.
• Some USB devices may be in-
compatible with your system.
• Depending on the USB device’s
type, capacity, or the format of
files, USB recognition time may
be longer.
• Image and video playback are
not supported.
6-22
06
%/8(7227+ǣ,)(48,33('Ǥ
Connecting Bluetooth devices • If Bluetooth connection is not
Bluetooth is a short-range wireless stable, follow these steps to try
networking technology. Via Blue- again.
tooth, you can connect nearby mobile 1. Deactivate Bluetooth and re-
devices wirelessly to send and re- activate it on the device. Then,
ceive data between connected devic- reconnect the device.
es. This enables you to use your de- 2. Turn the device off and on.
vices effectively. Then, reconnect it.
To use Bluetooth, you must first con- 3. Remove the battery from the
nect a Bluetooth-enabled device to device and reinstall it. Then,
your system, such as a mobile phone turn the device on and recon-
or an MP3 player. Ensure that the de- nect it.
vice you want to connect supports
Bluetooth. 4. Unregister the Bluetooth pair-
ing on both the system and
the device and then re-regis-
WARNING ter and connect them.
• The Bluetooth connection is un-
Park your vehicle in a safe location available when the device’s
before connecting Bluetooth de- Bluetooth functi on is turned off.
vices. Distracted driving can cause Be sure to turn on the device’s
a traffic accident and lead to per- Bluetooth function.
sonal injury or death.
2. On the Bluetooth device you want • You can change the permission
to connect, activate Bluetooth, settings via the mobile phone’s
search for your vehicle’s system, Bluetooth settings menu. For
and then select it. more information, refer to your
• Check the system’s Bluetooth mobile phone’s user guide.
name, which is displayed in the • To register a new device, repeat
new registration pop-up window steps 1 to 3.
on the system screen. • If you use the automatic Blue-
tooth connection function, a call
may be switched to the vehicle’s
Handsfree when you are taking
on the phone near the vehicle
while the vehicle’s engine is on.
If you do not want the system to
connect with the device auto-
3. Enter or confirm the passkey to matically, deactivate Bluetooth
confirm the connection. on your device.
• If the passkey input screen is • When a device is connected to
displayed on the Bluetooth de- the system via Bluetooth, the
vice screen, enter the passkey device’s battery may discharge
‘0000’ which is displayed on the faster.
system screen.
• If the 6-digit passkey is dis- Connecting a paired device
played on the Bluetooth device
screen, ensure that the Blue- To use a Bluetooth device on your
tooth passkey displayed on the system, connect the paired device to
Bluetooth device is the same as the system. Your system can connect
the passkey on the system with only one device at a time.
screen and confirm the connec- 1. From the control panel, press the
tion from the device. [PHONE] button, and then select
Phone Settings X Paired Devices.
NOTICE
• If there is no connected device,
press the Call/Answer button on
• The screen image in this manual the steering wheel.
is an example. Check your sys- 2. Turn the [TUNE] knob to select the
tem screen for the exact vehicle device to connect, and then press
name and Bluetooth device the knob.
name.
• If another device is already con-
• The default passkey is ‘0000’. nected to your system, discon-
• It may take a while for the system nect it. Select the connected de-
to connect with the device after vice to disconnect.
you permit the system to access
the device. When a connection is
made, the Bluetooth status icon
appears at the top of the screen.
6-24
06
NOTICE NOTICE
• If a connection ends because a • When you delete a paired de-
device is out of the connection vice, the Call history and Con-
range or a device error occurs, tacts stored in the system are
the connection will be restored also deleted.
automatically when the device • To re-use a deleted device, you
enters the connection range or must pair the device again.
when the error is cleared.
• Depending on auto connection
priority, connection to a device Using a Bluetooth audio device
may take time. You can listen to music stored in the
connected Bluetooth audio device via
your vehicle’s speakers.
Disconnecting a device
If you want to stop using a Bluetooth
device or connect another device, 1. On the control panel, press the
disconnect your currently connected [AUDIO] button.
device. 2. When the mode selection window
1. From the control panel, press the displays, turn the [TUNE] knob to
select Bluetooth audio and then
[PHONE] button, and then select press the knob.
Phone Settings X Paired Devices.
2. Turn the [TUNE] knob to select
your currently connected device
and then press the knob.
3. Press the [1 RPT] button to select
Yes.
6-25
Infotainment System
6-26
06
Playing the previous or next song NOTICE
To play the previous song, press the • Depending on the connected
[< SEEK] button twice on the control Bluetooth device, mobile phone,
panel. To play the next song, press or the music player you are us-
the [TRACK >] button on the control ing, playback controls may dif-
panel. fer.
• You can also push the Up/Down • Depending on the music player
lever on the steering wheel. you are using, streaming may
not be supported.
NOTICE • Depending on the connected
Bluetooth device or mobile
Depending on the connected Blue- phone, some functions may not
tooth device or mobile phone, be supported.
playing the previous/next song
• If a Bluetooth enabled phone is
may not be supported.
being used to play music and it
receives or makes a phone call,
Playing repeatedly the music will stop.
On the control panel, press the • Receiving an incoming call or
[1 RPT] button. The repeat mode making an outgoing call while
changes each time you press it. The playing Bluetooth audio may re-
corresponding mode icon will be dis- sult in audio interference.
played on the screen. • If you use the Bluetooth phone
mode while using Bluetooth au-
Playing in random order dio, playback may not automati-
cally resume after you end the
On the control panel, press the call depending on the connect-
[2 SHFL] button. The shuffle mode is ed mobile phone.
activated or deactivated each time
you press it. When you activate the • Moving the track up/down while
shuffle mode, the corresponding playing Bluetooth audio mode
mode icon will be displayed on the may result in pop noises with
screen. some mobile phones.
• The Rewinding/Fast forwarding
function is not supported in the
NOTICE Bluetooth audio mode.
Depending on the connected Blue- • The playlist feature is not sup-
tooth device or mobile phone, RPT ported in the Bluetooth audio
& SHFL features may not be sup- mode.
ported. • If the Bluetooth device is discon-
nected, Bluetooth audio mode
will end.
6-27
Infotainment System
6-28
06
Registering the favourites list NOTICE
You can more easily use Bluetooth to • You can register up to 20 favou-
talk on the phone hands-free by reg- rites for each device.
istering phone numbers as your fa- • You must first download the
vourites. contacts to the system to regis-
1. On the Phone screen, turn the ter favourites.
[TUNE] knob on the control panel • The favourites list saved on the
to select Favourites and press the mobile phone is not download-
knob. ed to the system.
2. Select [MENU/CLOCK] X Add • Even if the contact information
New Favourites. on the mobile phone is edited,
3. Press the [1 RPT] button, and se- the favourites on the system are
lect the desired phone number. not automatically edited. Delete
and add the item to favourites
again.
Using the favourites list
• When you connect a new mobile
1. From the Phone screen, turn the phone, your favourites set for
[TUNE] knob on the control panel the previous mobile phone will
to select Favourites, and then not be displayed, but they will
press the knob. remain in your system until you
2. Turn the [TUNE] knob to select the delete the previous phone from
desired contact, and then press the device list.
the knob to make a phone call.
Using your call history
1. From the Phone screen, turn the
[TUNE] knob on the control panel
to select Call history, and then
press the knob.
2. Turn the [TUNE] knob to select the
Press the [MENU/CLOCK] button on desired entry, and then press the
the control panel to access the follow- knob to make a phone call.
ing menu options:
• Add New Favourites: Add a fre-
quently used phone number to fa-
vourites.
• Delete Items: Delete a selected
favourites item.
• Delete All: Delete all favourites Press the [MENU/CLOCK] button on
items. the control panel to access the follow-
ing menu options:
6-29
Infotainment System
6-30
06
• Depending on the system’s Answering calls
specifications, some of the When a call comes in, a notification
downloaded contacts may be pop-up window of the incoming call
lost. appears on the system screen.
• Contacts stored both in the
phone and in the SIM card are
downloaded. With some mobile
phones, contacts in the SIM card
may not be downloaded.
• Special characters and figures
used in the contact name may
not be displayed properly. To answer the call, press the [1 RPT]
• Permission is required to down- button on the control panel.
load contacts from the mobile • Alternatively, press the Call/
phone. When you attempt to Answer button on the steering
download data, you may need to wheel.
permit the download on the mo-
bile phone. If the download fails,
To reject the call, press the [2 SHFL]
check the mobile phone screen
button on the control panel.
for any notification or the mobile
phone’s permission setting. • Alternatively, press the Call end
button on the steering wheel.
• Depending on the mobile phone
type or status, downloading may
take longer. NOTICE
• When you download your con- • Depending on the mobile phone
tacts, any old data will be deleted. type, call rejection may not be
• You cannot edit or delete your supported.
contacts on the system. • Once your mobile phone is con-
• When you connect a new mobile nected to the system, the call
phone, your contacts download- sound may be output through
ed from the previous mobile the vehicle’s speakers even af-
phone will not be displayed, but ter you exit the vehicle if the
they will remain in your system phone is within the connection
until you delete the previous range. To end the connection,
phone from the device list. disconnect the device from the
system or deactivate Bluetooth
on the device.
6-31
Infotainment System
6-32
06
6<67(067$786,&216
Status icons appear at the top of the Signal strength
screen to display the current system
Icon Description
status.
Familiarise yourself with the status Signal strength of the mobile phone
connected via Bluetooth
icons that appear when you perform
certain actions or functions and their
meanings. NOTICE
• The battery level displayed on
the screen may differ from the
battery level displayed on the
connected device.
• The signal strength displayed
on the screen may differ from
the signal strength displayed on
the connected mobile phone.
Bluetooth
• Depending on vehicle models
Icon Description and specifications, some status
Battery level of connected icons may not be displayed.
Bluetooth device
Mobile phone or audio device con-
nected via Bluetooth
6-33
Infotainment System
$8',26<67(063(&,),&$7,216
USB NOTICE
Supported audio formats • Files that are not in a supported
• Audio file specification format may not be recognised or
played, or information about
- WAVeform audio format them, such as the file name, may
- MPEG1/2/2.5 Audio Layer3 not be displayed properly.
- Windows Media Audio Ver • Only files with .mp3/.wma/.wav
7.X/8.X extensions can be recognised
• Bit rates by the system. If the file is not in
- MPEG1 (Layer3): supported format, change the
32/40/48/56/64/80/96/112/128/ file format by using the latest
160/192/224/256/320 kbps encoding software.
- MPEG2 (Layer3): • The device will not support files
8/16/24/32/40/48/56/64/80/96/ locked by DRM (Digital Rights
112/128/144/160 kbps Management).
- MPEG2.5 (Layer3): • For MP3/WMA compression files
8/16/24/32/40/48/56/64/80/96/ and WAV file, differences in
112/128/144/160 kbps sound quality will occur depend-
ing on the bitrate. (Music files
- WMA (High Range): with a higher bitrate have a bet-
48/64/80/96/128/160/192 kbps ter sound quality.)
• Bits Per Sample • Japanese or Simplified Chinese
- WAV (PCM(Stereo)): 24 bit characters in folder or file names
- WAV (IMA ADPCM): 4 bit may not be displayed properly.
- WAV (MS ADPCM): 4 bit
• Sampling frequency Supported USB storage devices
- MPEG1: 44100/48000/32000 Hz • Byte/Sector: 64 kbyte or less
- MPEG2: 22050/24000/16000 Hz • Format system: FAT12/16/32 (rec-
- MPEG2.5: 11025/12000/8000 Hz ommended), exFAT/NTFS
- WMA: 32000/44100/48000 Hz
- WAV: 44100/48000 Hz
• Maximum length of folder/file
names (Based on Unicode): 40
English or Korean characters
• Supported characters for folder/file
names (Unicode support): 2,604
Korean characters, 94 alphanu-
meric characters, 4,888 Chinese
characters in common use, 986
special characters
• Maximum number of folders: 1,000
• Maximum number of files: 5,000
6-34
06
75$'(0$5.6
NOTICE Other trademarks and trade names
• Operation is guaranteed only for are those of their respective owners.
a metal cover type USB storage
device with a plug type connec- • The Bluetooth® word mark and lo-
tor. gos are registered trademarks
- USB storage devices with a owned by Bluetooth SIG, Inc. and
plastic plug may not be rec- any use of such marks by HYUND-
ognised. AI is under licence.
- USB storage devices in mem-
ory card types, such as CF
card or SD cards, may not be
recognised.
• USB hard disk drives may not be
recognised.
• When you use a large capacity
USB storage device with multi-
ple logical drives, only files
stored on the first drive will be
recognised.
• If an application program is
loaded on a USB storage device,
the corresponding media files
may not play.
• Use USB 2.0 devices for better
compatibility.
Bluetooth
• Aerial power: Max 3 mW
6-35
7. Driving your vehicle
7
07
WARNING
Carbon monoxide (CO) gas is toxic. Breathing CO can cause uncon-
sciousness and death.
Engine exhaust contains carbon monoxide which cannot be seen or smelled.
Avoid idling the engine for prolonged periods with people inside the vehi-
cle.
If it is necessary to idle the engine for a prolonged period with people inside the
vehicle , be sure to do so only in an open area with the air intake set at “Fresh”
and fan control set to high so fresh air is drawn into the interior.
7-3
Driving your vehicle
BEFORE DRIVING
Before entering the vehicle For more information, refer to
• Be sure all windows, outside mir- “Seat Belts” in chapter 2.
ror(s), and outside lights are clean • Always drive defensively. As-
and unobstructed. sume other drivers or pedestri-
• Remove frost, snow, or ice. ans may be careless and make
mistakes.
• Visually check the tires for uneven
wear and damage. • Stay focused on the task of driv-
ing. Driver distraction can cause
• Check under the vehicle for any accidents.
sign of leaks.
• Leave plenty of space between
• Be sure there are no obstacles be- you and the vehicle in front of
hind you if you intend to back up. you.
Before starting
WARNING
• Make sure the hood, the tailgate,
and the doors are securely closed NEVER drink or take drugs and
and locked. drive.
• Adjust the position of the seat and Drinking or taking drugs and driv-
steering wheel. ing is dangerous and may result in
• Adjust the inside and outside rear- an accident and SERIOUS INJURY
view mirrors. or DEATH.
• Verify all the lights work. Drunk driving is the number one
contributor to the highway death
• Fasten your seatbelt. Check that
toll each year. Even a small amount
all passengers have fastened their
of alcohol will affect your reflexes,
seatbelts.
perceptions and judgment. Just
• Check the gauges and indicators one drink can reduce your ability
in the instrument panel and the to respond to changing conditions
messages on the instrument dis- and emergencies and your reac-
play when the ignition switch is in tion time gets worse with each ad-
the ON position. ditional drink.
• Check that any items you are car- Driving while under the influence
rying are stored properly or fas- of drugs is as dangerous or more
tened down securely. dangerous than driving under the
influence of alcohol.
WARNING You are much more likely to have a
serious accident if you drink or
To reduce the risk of SERIOUS IN- take drugs and drive. If you are
JURY or DEATH, take the following drinking or taking drugs, don’t
precautions: drive. Do not ride with a driver who
• ALWAYS wear your seat belt. All has been drinking or taking drugs.
passengers must be properly Choose a designated driver or call
belted whenever the vehicle is a taxi.
moving.
7-4
07
IGNITION SWITCH
WARNING Key ignition switch
(if equipped)
To reduce the risk of SERIOUS IN-
JURY or DEATH, take the following
precautions:
• NEVER allow children or any
person who is unfamiliar with
the vehicle to touch the ignition
switch or related parts. Unex-
pected and sudden vehicle
movement can occur.
• NEVER reach through the steer-
ing wheel for the ignition switch, OIB054010
or any other control, while the
vehicle is in motion. The pres-
ence of your hand or arm in this WARNING
area may cause a loss of vehicle • NEVER turn the ignition switch
control resulting in an accident. to the LOCK or ACC position
while the vehicle is in motion ex-
cept in an emergency. This will
result in the engine turning off
and loss of power assist for the
steering and brake systems.
This may lead to loss of direc-
tional control and braking func-
tion, which could cause an acci-
dent.
• Before leaving the driver’s seat,
always make sure the shift lever
is in 1st gear (for manual trans-
mission vehicle) or P (Park) po-
sition (for dual clutch transmis-
sion vehicle), apply the parking
brake, and turn ignition switch
to the LOCK position.
Unexpected vehicle movement
may occur if these precautions
are not followed.
7-5
Driving your vehicle
7-6
07
Starting the engine Vehicle with dual clutch transmission :
1. Make sure the parking brake is ap-
WARNING plied.
• Always wear appropriate shoes 2. Make sure the shift lever is in P
when operating your vehicle. (Park).
Unsuitable shoes, such as high 3. Depress the brake pedal.
heels, ski boots, sandals, flip- 4. Turn the ignition switch to the
flops, etc., may interfere with START position. Hold the key
your ability to use the brake, ac- (maximum of 10 seconds) until the
celerator and clutch pedals. engine starts and release it.
• Do not start the vehicle with the
accelerator pedal depressed.
The vehicle can move and lead i Information
to an accident. • Do not wait for the engine to warm
• Wait until the engine rpm is nor- up while the vehicle remains sta-
mal. The vehicle may suddenly tionary.
move if the brake padel is re- Start driving at moderate engine
leased when the rpm is high. speeds. (Steep accelerating and de-
celerating should be avoided.)
Starting the petrol engine • Always start the vehicle with your
Vehicle with manual transmission : foot on the brake pedal. Do not de-
1. Make sure the parking brake is ap- press the accelerator while starting
plied. the vehicle. Do not race the engine
while warming it up.
2. Make sure the shift lever is in neu-
tral.
3. Depress the clutch and brake ped- Starting the diesel engine
als. To start the diesel engine when the
4. Turn the ignition switch to the engine is cold, it has to be pre-heated
START position. Hold the key before starting the engine and then
(maximum of 10 seconds) until the have to be warmed up before starting
engine starts and release it. to drive.
Vehicle with manual transmission :
1. Make sure the parking brake is ap-
plied.
2. Make sure the shift lever is in neu-
tral.
3. Depress the clutch and brake ped-
als.
4. Turn the ignition switch to the ON
position to pre-heat the engine.
The glow indicator light ( ) w ill
illuminate.
7-7
Driving your vehicle
5. When the glow indicator light ( ) Starting and stopping the engine for
goes out, turn the key ignition turbocharger intercooler
switch to the START position. Hold 1. Do not race or accelerate the en-
the key (maximum of 10 seconds) gine immediately after starting the
until the engine starts and release engine.
it. If the engine is cold, idle for several
seconds before sufficient lubrica-
Vehicle with dual clutch transmission: tion is ensured in the turbo charger
unit.
1. Make sure the parking brake is ap-
plied. 2. After high speed or extended driv-
ing that requires heavy engine load,
2. Make sure the shift lever is in P
idle the engine about one minute
(Park).
before turning the engine off.
3. Depress the brake pedal.
This idle time will allow the turbo-
4. Turn the ignition switch to the ON charger to cool prior to shutting the
position to pre-heat the engine. engine off.
The glow indicator light ( ) will
illuminate.
5. When the glow indicator light ( ) NOTICE
goes out, turn the key ignition Do not turn off the engine immedi-
switch to the START position. Hold ately after it has been subjected to
the key (maximum of 10 seconds) a heavy load. Doing so may cause
until the engine starts and release severe damage to the engine or tu
it. rbo charger unit.
i Information NOTICE
If the engine does not start within 10 To prevent damage to the vehicle:
seconds after preheating is completed, • Do not hold the ignition key in
turn the ignition switch once more to the START position for more
the LOCK position and wait for 10 sec- than 10 seconds. Wait 5 to 10
onds. Then turn the ignition switch to seconds before trying again.
the ON position in order to preheat the • Do not turn the ignition switch
engine again. to the START position with the
engine running. It may damage
the starter.
• If traffic and road conditions
permit, you may put the shift le-
ver in the N (Neutral) position
while the vehicle is still moving
and turn the ignition switch to
the START position in an at-
tempt to restart the engine.
• Do not push or tow your vehicle
to start the engine.
7-8
07
Engine Start/Stop button WARNING
(if equipped)
• NEVER press the Engine Start/
Stop button while the vehicle is
in motion except in an emergen-
cy. This will result in the engine
turning off and loss of power as-
sist for the steering and brake
systems.
This may lead to loss of direc-
tional control and braking func-
tion, which could cause an acci-
OQXI059001 dent.
Whenever the front door is opened, • Before leaving the driver’s seat,
the Engine Start/Stop button will illu- always make sure the shift lever
minate and will go off 30 seconds af- is in neutral, set the parking
ter the door is closed. brake, press the Engine Start/
Stop button to the OFF position,
and take the Smart Key with you.
WARNING Unexpected vehicle movement
may occur if these precautions
To reduce risk of serious injury or
are not followed.
death, NEVER allow children or
any person who is unfamiliar with • NEVER reach through the steer-
the vehicle to touch the Engine ing wheel for the Engine Start/
Start/Stop button or related parts. Stop button or any other control
Unexpected and sudden vehicle while the vehicle is in motion.
movement can occur. The presence of your hand or
arm in this area may cause a
loss of vehicle control resulting
WARNING in an accident.
To turn the engine off in an emer-
gency:
Press and hold the Engine Start/
Stop button for more than two sec-
onds OR Rapidly press and release
the Engine Start/Stop button three
times (within three seconds).
If the vehicle is still moving, you
can restart the engine without de-
pressing the brake pedal by press-
ing the Engine Start/Stop button
with the shift lever in the N (Neu-
tral) position.
7-9
Driving your vehicle
ACC • Press the Engine Start/Stop • If you leave the Engine Start/
button when the button is in Stop button in the ACC posi-
the OFF position without de- tion for more than one hour,
pressing the clutch pedal. the battery power will turn off
• Electrical accessories are automatically to prevent the
usable. battery from discharging.
• The steering wheel unlocks. • If the steering wheel doesn’t
unlock properly, the Engine
Start/Stop button will not
work. Press the Engine Start/
Stop button while turning the
steering wheel right and left
to release tension.
7-10
07
- Vehicle with manual transmission
Button Position Action Notice
ON • Press the Engine Start/Stop Do not leave the Engine Start/
button while it is in the ACC Stop button in the ON position
position without depressing when the engine is not running
the clutch pedal. to prevent the battery from dis-
charging.
• The warning lights can be
checked before the engine is
started.
START To start the engine, depress If you press the Engine Start/
the clutch and brake pedals Stop button without depressing
and press the Engine Start/ the clutch pedal, the engine
Stop button with the shift lever does not start and the Engine
in neutral. Start/Stop button changes as
follows:
OFF o ACC o ON o OFF
7-11
Driving your vehicle
ACC Press the Engine Start/Stop • If you leave the Engine Start/
button when the button is in the Stop button in the ACC posi-
OFF position without depress- tion for more than one hour,
ing the brake pedal. the battery power will turn off
Electrical accessories are us- automatically to prevent the
able. battery from discharging.
The steering wheel unlocks.
• If the steering wheel doesn’t
unlock properly, the Engine
Start/Stop button will not
work. Press the Engine Start/
Stop button while turning the
steering wheel right and left
to release tension.
7-12
07
- Vehicle with dual clutch transmission
Button Position Action Notice
ON Press the Engine Start/Stop Do not leave the Engine Start/
button while it is in the ACC po- Stop button in the ON position
sition without depressing the when the engine is not running
brake pedal. to prevent the battery from dis-
The warning lights can be charging.
checked before the engine is
started.
START To start the engine, depress If you press the Engine Start/
the brake pedal and press the Stop button without depressing
Engine Start/Stop button with the brake pedal, the engine
the shift lever in the P (Park) or does not start and the Engine
in the N (Neutral) position. Start/Stop button changes as
For your safety, start the en- follows:
gine with the shift lever in the P OFF o ACC o ON o OFF or
(Park) position. ACC
7-13
Driving your vehicle
7-14
07
i Information Starting the diesel engine
To start the diesel engine when the
• Do not wait for the engine to warm engine is cold, it has to be pre-heated
up while the vehicle remains sta- before starting the engine and then
tionary. have to be warmed up before starting
Start driving at moderate engine to drive.
speeds. (Steep accelerating and de- Vehicle with manual transmission :
celerating should be avoided.) 1. Always carry the smart key with
• Always start the vehicle with your you.
foot on the brake pedal. Do not de- 2. Make sure the parking brake is ap-
press the accelerator while starting plied.
the vehicle. Do not race the engine
while warming it up. 3. Make sure the shift lever is in neu-
tral.
• When you start to drive, move the
shift lever after checking the RP- 4. Depress the clutch and brake ped-
M(revolutions per minute) is in the als.
proper range (under 1000 rpm) by 5. Press the Engine Start/Stop but-
depressing the clutch pedal and ton.
brake pedal. 6. Continue depressing the brake
After releasing the parking brake, pedal until the glow indicator light
take your foot off the clutch and de- ( ) goes out.
press the accelerator slowly while 7. When the glow indicator light ( )
starting your vehicle. goes out, the engine will start.
7-15
Driving your vehicle
7-16
07
NOTICE
To prevent damage to the vehicle:
• If the engine stalls while you are
in motion, do not attempt to
move the shift lever to the P
(Park) position.
If traffic and road conditions
permit, you may put the shift le-
ver in the N (Neutral) position
OQXI059002
while the vehicle is still moving
and press the Engine Start/Stop i Information
button in an attempt to restart
the engine. If the smart key battery is weak or the
• Do not push or tow your vehicle smart key does not work correctly, you
to start the engine. can start the engine by pressing the
Engine Start/Stop button with the
smart key in the direction of the pic-
NOTICE ture above.
To prevent damage to the vehicle:
When the stop lamp fuse is blown,
you can’t start the engine normal-
ly. Replace the fuse with a new
one. If you are not able to replace
the fuse, you can start the engine
by pressing and holding the En-
gine Start/Stop button for 10 sec-
onds with the Engine Start/Stop
button in the ACC position.
Do not press the Engine Start/Stop
button for more than 10 seconds
except when the stop lamp fuse is
blown.
For your safety always depress the
brake and/or clutch pedal before
starting the engine.
7-17
Driving your vehicle
0$18$/75$160,66,21ǣ,)(48,33('Ǥ
ٻType A Manual transmission operation
The manual transmission has 5 (or 6)
forward gears. The transmission is
fully synchronized in all forward gears
so shifting to either a higher or a low-
er gear is easily accomplished.
WARNING
OQXI059003 Before leaving the driver’s seat, al-
ٻType B
ways make sure the shift lever is in
1st gear when the vehicle is parked
on a uphill and in R (Reverse) on a
downhill, set the parking brake,
and place the ignition switch in the
LOCK/OFF position. Unexpected
vehicle movement may occur if
these precautions are not fol-
lowed.
i Information
During cold weather, shifting may be
difficult until the transmission lubri-
cant has warmed up.
7-18
07
Using the clutch (if equipped) Downshifting
The clutch pedal should be depressed Downshift when you must slow down
all the way to the floor before: in heavy traffic or drive up a steep hill
- Starting the engine to prevent engine load.
The engine will not start without Also, downshifting reduces the
depressing the clutch pedal. chance of stalling and can accelerate
when you need to increase your
- Shifting speed again.
- To start your vehicle, slowly re- When the vehicle is going downhill,
lease the clutch pedal and depress downshifting helps maintain safe
the accelerator. speed by providing brake power from
the engine and enables less wear on
When releasing the clutch pedal, re- the brakes.
lease it slowly. The clutch pedal
should always be released while driv-
ing. NOTICE
To prevent damage to the engine,
clutch and transmission :
NOTICE
• When downshifting from 5th
To prevent unnecessary wear or gear to 4th gear, be careful not
damage to the clutch: to inadvertently push the shift
• Do not rest your foot on the lever sideways engaging the
clutch pedal while driving. 2nd gear. A drastic downshift
• Do not hold the vehicle with the may cause the engine speed to
clutch on an incline, while wait- increase to the point the ta-
ing for the traffic light, etc. chometer will enter the red-zone.
• Always depress the clutch pedal • Do not downshift more than two
down fully to prevent noise or gear at a time or downshift the
damage. gear when the engine is running
at high speed (5,000 RPM or
• Do not start with the 2nd (sec- higher). Such a downshifting
ond) gear engaged except when may damage the engine, clutch
you start on a slippery road. and the transmission.
• Depress the clutch pedal all the
way and be careful not to de-
press the pedal again before re-
turning to the upright position
after you release the pedal. If
you depress the pedal before re-
turning to the original position
repeatedly, it may cause the
clutch system failure.
7-19
Driving your vehicle
WARNING
Do not use the engine brake (shift-
ing from a higher gear to lower
gear) rapidly on slippery roads.
The vehicle may slip causing an
accident.
7-20
07
'8$/&/87&+75$160,66,21ǣ,)(48,33('Ǥ
OQXI059017
Depress the brake pedal and press the shift button while moving the shift lever.
Press the shift button while moving the shift lever.
The shift lever can freely operate.
7-21
Driving your vehicle
7-22
07
WARNING LCD display for transmission
temperature and warning mes-
To reduce the risk of serious injury sage
or death: Transmission temperature
• ALWAYS check the surrounding gauge
areas near your vehicle for peo-
ple, especially children, before
shifting a vehicle into D (Drive)
or R (Reverse).
• Before leaving the driver’s seat,
always make sure the shift lever
is in the P (Park) position, then
set the parking brake, and place
the ignition switch in the LOCK/
OFF position. Unexpected and
sudden vehicle movement can OAD058179N
occur if these precautions are
not followed.
• Do not use aggressive engine
braking (shifting from a higher
gear to a lower gear) on slippery
roads. This could cause the tires
to slip and may result in an acci-
dent.
NOTICE OJS058137L
• Always come to a complete stop • Select trip computer mode on the
before shifting into D (Drive) or LCD display and move to the trans-
R (Reverse). mission temperature screen to see
• Do not put the shift lever in N the temperature of the dual clutch
(Neutral) while driving. transmission.
• Try to drive so that the temperature
gauge do not show high/overheat.
WARNING When the transmission is over-
If the transmission cannot shift heated, the warning message will
into Drive or Reverse, the position display on the LCD. Follow the dis-
indicator D or R) on the cluster will played message.
blink. We recommend that you
contact an authorized Hyundai
dealer to have the system checked.
7-23
Driving your vehicle
i Information
The temperature gauge may increase
rapidly if clutch slip occurs excessively
due to repeated stop-and-go driving on
steep grades and when Hill Hold is
maintained for a long time. In order to
prevent excessive temperature in-
crease, use the brake during low speed
driving or when stopping the vehicle
on a hill.
7-24
07
High/Overheat DCT warning messages
(from marking 15 to 16) This warning message is displayed
when vehicle is driven slowly on a
grade and the vehicle detects that the
brake pedal is not applied.
OAD058180N
• This zone shows that the dual
clutch temperature of the DCT has
entered the high/overheat zone. OAD058175N
The DCT warning alarm sounds, Steep grade
warning message is displayed on Driving up hills or on steep grades:
the cluster and the temperature
gauge disappears from the cluster. • To hold the vehicle on an incline
Follow the displayed warning mes- use the foot brake or the parking
sage. brake.
• To check the temperature status of • When in stop-and-go traffic on an
the dual clutch when overheated, incline, allow a gap to form ahead
move to the temperature gauge of you before moving the vehicle
screen by selecting the trip com- forward. Then hold the vehicle on
puter mode. Then, you can check the incline with the foot brake.
the temperature status of the dual • If the vehicle is held on a hill by ap-
clutch. plying the accelerator pedal or by
creeping with the brake pedal dis-
engaged, the clutch and transmis-
sion may overheat which can re-
sult in damage. At this time, a
warning message will appear on
the LCD display.
• If the LCD warning is active, the
foot brake must be applied.
• Ignoring the warnings can lead to
damage to the transmission.
7-25
Driving your vehicle
OJS058139L
7-26
07
Transmission overheated Transmission ranges
• If the vehicle continues to be driv- The indicator in the instrument cluster
en and the clutch temperatures displays the shift lever position when
reach the maximum temperature the ignition switch is in the ON posi-
limit, the “Trans Hot! Park with en- tion.
gine on” warning will be displayed.
When this occurs the clutch is dis-
abled until the clutch cools to nor- P (Park)
mal temperatures. Always come to a complete stop be-
• The warning will display a time to fore shifting into P (Park).
wait for the transmission to cool. To shift from P (Park), you must de-
• If this occurs, pull over to a safe lo- press firmly on the brake pedal and
cation, stop the vehicle with the en- make sure your foot is off the acceler-
gine running, apply the brakes and ator pedal.
shift the vehicle to P (Park) with If you have done all of the above
engine on, and allow the transmis- and still cannot shift the lever out
sion to cool. of P (Park), see “Shift-Lock Re-
• When the message “Trans cooled. lease” in this chapter.
Resume driving.” appears you can The shift lever must be in P (Park) be-
continue to drive your vehicle. fore turning the engine off.
• When possible, drive the vehicle
smoothly. WARNING
• Shifting into P (Park) while the
If any of the warning messages in the vehicle is in motion may cause
LCD display continue to blink, for you to lose control of the vehicle.
your safety, we recommend you con-
tact an authorized HYUNDAI dealer • After the vehicle has stopped,
and have the system checked. always make sure the shift lever
is in P (Park), apply the parking
brake, and turn the engine off.
• When parking on an incline,
block the wheels to prevent the
vehicle from rolling down.
• For safety, always engage the
parking brake with the shift le-
ver in the P (Park) position ex-
cept for the case of emergency
parking.
7-27
Driving your vehicle
R (Reverse)
Use this position to drive the vehicle
backward.
NOTICE
Always come to a complete stop
before shifting into or out of R (Re-
verse); you may damage the trans-
mission if you shift into R (Re-
OQXI059018
verse) while the vehicle is in
motion. Manual shift mode
Whether the vehicle is stationary or in
N (Neutral) motion, manual shift mode is select-
The wheels and transmission are not ed by pushing the shift lever from the
engaged. D (Drive) position into the manual
gate. To return to D (Drive) range op-
Use N (Neutral) if you need to restart eration, push the shift lever back into
a stalled engine, or if it is necessary the main gate.
to stop with the engine ON. Shift into
P (Park) if you need to leave your ve- In manual shift mode, moving the
hicle for any reason. shift lever backwards and forwards
will allow you to make gearshifts rap-
Always depress the brake pedal idly.
when you are shifting from N (Neu-
tral) to another gear. Up (+) : Push the lever forward once
to shift up one gear.
Down (-) : Pull the lever backwards
D (Drive) once to shift down one
This is the normal driving position. gear.
The transmission will automatically
shift through a 7-gear sequence, pro-
viding the best fuel economy and
power.
For extra power when passing anoth-
er vehicle or driving uphill, depress
the accelerator fully. The transmis-
sion will automatically downshift to
the next lower gear (or gears, as ap-
propriate).
7-28
07
i Information Shift-lock release
If the shift lever cannot be moved
• Only the seven forward gears can be from the P (Park) position into R (Re-
selected. To reverse or park the ve- verse) position with the brake pedal
hicle, move the shift lever to the R depressed, continue depressing the
(Reverse) or P (Park) position as re- brake, and then do the following:
quired.
• Downshifts are made automatically
when the vehicle slows down. When
the vehicle stops, 1st gear is auto-
matically selected.
• When the engine rpm approaches
the red zone the transmission will
upshift automatically.
• If the driver presses the lever to +
(Up) or - (Down) position, the trans-
OQXI059020
mission may not make the requested
gear change if the next gear is out- 1. Press the shift-lock release button.
side of the allowable engine rpm 2. Press and hold the lock release
range. The driver must execute up- button on the shift lever.
shifts in accordance with road con- 3. Move the shift lever.
ditions, taking care to keep the en-
gine rpms below the red zone. 4. Have your vehicle inspected by an
authorized HYUNDAI dealer im-
mediately
Shift-lock system
For your safety, the dual clutch trans-
mission has a shift-lock system which
prevents shifting the transmission
from P (Park) into R (Reverse) unless
the brake pedal is depressed.
To shift the transmission from P
(Park) into R (Reverse):
1. Depress and hold the brake pedal.
2. Start the engine or place the igni-
tion switch in the ON position.
3. Move the shift lever.
7-29
Driving your vehicle
7-30
07
• Exercise extreme caution when WARNING
driving on a slippery surface. Be
especially careful when braking, To reduce the risk of SERIOUS IN-
accelerating or shifting gears. On a JURY or DEATH:
slippery surface, an abrupt change • ALWAYS wear your seatbelt. In
in vehicle speed can cause the a collision, an unbelted occu-
drive wheels to lose traction and pant is significantly more likely
may cause loss of vehicle control to be seriously injured or killed
resulting in an accident than a properly belted occupant.
• Optimum vehicle performance and • Avoid high speeds when corner-
economy is obtained by smoothly ing or turning.
depressing and releasing the ac-
celerator. • Do not make quick steering
wheel movements, such as
sharp lane changes or fast,
sharp turns.
• The risk of rollover is greatly in-
creased if you lose control of
your vehicle at highway speeds.
• Loss of control often occurs if
two or more wheels drop off the
roadway and the driver over
steers to reenter the roadway.
• In the event your vehicle leaves
the roadway, do not steer sharp-
ly. Instead, slow down before
pulling back into the travel
lanes.
• HYUNDAI recommends you fol-
low all posted speed limits.
7-31
Driving your vehicle
BRAKING SYSTEM
Power brakes • Wet brakes may impair the vehi-
Your vehicle has power-assisted cle’s ability to safely slow down;
brakes that adjust automatically the vehicle may also pull to one
through normal usage. side when the brakes are ap-
plied. Applying the brakes light-
If the engine is not running or is ly will indicate whether they
turned off while driving, the power as- have been affected in this way.
sist for the brakes will not work. You Always test your brakes in this
can still stop your vehicle by applying fashion after driving through
greater force to the brake pedal than deep water. To dry the brakes,
typical. The stopping distance, how- lightly tap the brake pedal to
ever, will be longer than with power heat up the brakes while main-
brakes. taining a safe forward speed un-
When the engine is not running, the til brake performance returns to
reserve brake power is partially de- normal. Avoid driving at high
pleted each time the brake pedal is speeds until the brakes function
applied. Do not pump the brake pedal correctly.
when the power assist has been in-
terrupted.
Pump the brake pedal only when Disc brakes wear indicator
necessary to maintain steering con- When your brake pads are worn and
trol on slippery surfaces. new pads are required, you will hear
a high pitched warning sound from
your front or rear brakes. You may
WARNING hear this sound come and go or it
may occur whenever you depress the
Take the following precautions: brake pedal.
• Do not drive with your foot rest- Please remember some driving con-
ing on the brake pedal. This will ditions or climates may cause a brake
create abnormal high brake tem- squeal when you first apply (or lightly
peratures, excessive brake lin- apply) the brakes. This is normal and
ing and pad wear, and increased does not indicate a problem with your
stopping distances. brakes.
• When descending a long or
steep hill, shift to a lower gear
and avoid continuous applica- NOTICE
tion of the brakes. Applying the To avoid costly brake repairs, do
brakes continuously will cause not continue to drive with worn
the brakes to overheat and could brake pads.
result in a temporary loss of
braking performance.
i Information
Always replace brake pads as complete
front or rear axle sets.
7-32
07
Rear drum brakes
Your rear drum brakes do not have
wear indicators.Therefore, have the
rear brake linings inspected if you
hear a rear brake rubbing noise. Also
have your rear brakes inspected each
time you change or rotate your tires
and when you have the front brakes
replaced.
OQXI059006
Parking brake To release:
Firmly depress the brake pedal.
Slightly pull up the parking brake le-
ver.
While pressing the release button (1),
lower the parking brake (2).
7-33
Driving your vehicle
7-34
07
Anti-lock Brake System (ABS) Using ABS
To obtain the maximum benefit from
your ABS in an emergency situation,
WARNING do not attempt to modulate your
An Anti-Lock Braking System brake pressure and do not try to
(ABS) will not prevent accidents pump your brakes. Depress your
due to improper or dangerous driv- brake pedal as hard as possible.
ing maneuvers. Even though vehi- When you apply your brakes under
cle control is improved during conditions which may lock the wheels,
emergency braking, always main- you may hear sounds from the
tain a safe distance between you brakes, or feel a corresponding sen-
and objects ahead of you. Vehicle sation in the brake pedal. This is nor-
speeds should always be reduced mal and it means your ABS is active.
during extreme road conditions. ABS does not reduce the time or dis-
The braking distance for cars tance it takes to stop the vehicle.
equipped with ABS may be longer
than for those without these sys- Always maintain a safe distance from
tems in the following road condi- the vehicle in front of you.
tions. ABS will not prevent a skid that re-
Drive your vehicle at reduced sults from sudden changes in direc-
speeds during the following condi- tion, such as trying to take a corner
tions: too fast or making a sudden lane
change. Always drive at a safe speed
• Rough, gravel or snow-covered for the road and weather conditions.
roads.
ABS cannot prevent a loss of stabili-
• On roads where the road sur- ty. Always steer moderately when
face is pitted or has different braking hard. Severe or sharp steer-
surface height. ing wheel movement can still cause
• Tire chains are installed on your your vehicle to veer into oncoming
vehicle. traffic or off the road.
The safety features of an ABS On loose or uneven road surfaces,
equipped vehicle should not be operation of the anti-lock brake sys-
tested by high speed driving or tem may result in a longer stopping
cornering. This could endanger distance than for vehicles equipped
the safety of yourself or others. with a conventional brake system.
The ABS warning light ( ) will stay
ABS is an electronic braking system on for several seconds after the
that helps prevent a braking skid. ignition switch is in the ON position.
ABS allows the driver to steer and During that time, the ABS will go
brake at the same time. through self-diagnosis and the light
will go off if everything is normal. If
the light stays on, you may have a
problem with your ABS. We recom-
mend that you contact an authorized
HYUNDAI dealer as soon as possi-
ble.
7-35
Driving your vehicle
CAUTION
OQXI059007
When you drive on a road having
poor traction, such as an icy road, The Electronic Stability Control (ESC)
and apply your brakes continuously, system helps to stabilize the vehicle
the ABS will be active continuously during cornering maneuvers.
and the ABS warning light ( ) may ESC checks where you are steering
illuminate. Pull your car o v e r and where the vehicle is actually go-
to a safe place and turn the engine ing.
off.
ESC applies braking pressure to any
Restart the engine. If the ABS one of the vehicle’s brakes and inter-
warning light is off, then your ABS venes in the engine management
system is normal. Otherwise, you system to assist the driver with keep-
may have a problem with your ABS ing the vehicle on the intended path.
system. We recommend that you It is not a substitute for safe driving
contact an authorized HYUNDAI practices. Always adjust your speed
dealer as soon as possible. and driving to the road conditions.
i Information WARNING
When you jump start your vehicle be- Never drive too fast for the road
cause of a drained battery, the ABS conditions or too quickly when
warning light ( ) may turn on at the cornering. The ESC system will
same time. This happens be- not prevent accidents.
cause of the low battery voltage. It does
not mean your ABS is malfunctioning. Excessive speed in turns, abrupt
Have the battery recharged before maneuvers, and hydroplaning on
driving the vehicle. wet surfaces can result in severe
accidents.
7-36
07
ESC operation ESC OFF condition
ESC ON condition To cancel ESC operation :
When the ignition switch is in the ON
position, the ESC and the ESC OFF
indicator lights illuminate for approxi-
mately three seconds. After both
lights go off, the ESC is enabled. • State 1
Press the ESC OFF button briefly.
The ESC OFF indicator light and/or
When operating message “Traction Control disabled”
When the ESC is in opera- will illuminate (if equipped with super-
tion, the ESC indicator vision cluster). In this state, the trac-
light blinks: tion control function of ESC (engine
management) is disabled, but the
• When you apply your brakes under brake control function of ESC (brak-
conditions which may lock the ing management) still operates.
wheels, you may hear sounds from
the brakes, or feel a corresponding • State 2
sensation in the brake pedal. This
Press and hold the ESC OFF button
is normal and it means your ESC is
continuously for more than 3 sec-
active.
onds. The ESC OFF indicator light
• When the ESC activates, the en- and/or message “Traction & Stability
gine may not respond to the accel- Control disabled” illuminates (if
erator as it does under routine con- equipped with supervision cluster)
ditions. and a warning chime sounds. In this
• If the Cruise Control was in use state, both the traction control func-
when the ESC activates, the Cruise tion of ESC (engine management)
Control automatically disengages. and the brake control function of ESC
The Cruise Control can be reen- (braking management) are disabled.
gaged when the road conditions If the ignition switch is placed in the
allow. See “Cruise Control Sys- LOCK/OFF position when ESC is off,
tem” later in this chapter (if ESC remains off. Upon restarting the
equipped). vehicle, the ESC will automatically
• When moving out of the mud or turn on again.
driving on a slippery road, the en-
gine rpm (revolutions per minute)
may not increase even if you press
the accelerator pedal deeply. This
is to maintain the stability and trac-
tion of the vehicle and does not in-
dicate a problem.
7-37
Driving your vehicle
7-39
Driving your vehicle
NOTICE WARNING
Driving with wheels and tires with
different sizes may cause the ESC Always be ready to depress the ac-
system to malfunction. Before re- celerator pedal when starting off
placing tires, make sure all four on a incline. The HAC activates
tires and wheels are the same size. only for approximately 2 seconds.
Never drive the vehicle with differ-
ent sized tires and wheels in-
stalled.
i Information
• The HAC does not operate when the
shift lever is in P (Park) or N (Neu-
tral).
• The HAC activates even when the
ESC (Electronic Stability Control)
is off. However, it does not activate,
when the ESC does not operate nor-
mally.
7-40
07
Good braking practices If a tire goes flat while you are driving,
apply the brakes gently and keep the
vehicle pointed straight ahead while
WARNING you slow down. When you are mov-
Whenever leaving the vehicle or ing slowly enough for it to be safe to
parking, always come to a com- do so, pull off the road and stop in a
plete stop and continue to depress safe location.
the brake pedal. Move the shift le- Keep your foot firmly on the brake
ver into the 1st gear (for manual pedal when the vehicle is stopped to
transmission vehicle) or P (Park) prevent the vehicle from rolling for-
position (for dual clutch transmis- ward.
sion vehicle), then apply the park-
ing brake, and place the ignition
switch in the LOCK/OFF position.
Vehicles with the parking brake
not fully engaged are at risk for
moving inadvertently and causing
injury to yourself or others.
7-41
Driving your vehicle
,6*ǣ,'/(6723$1'*2Ǥ6<67(0ǣ,)(48,33('Ǥ
The ISG system is to reduce the fuel - The vehicle is driven on a steep in-
consumption by automatically shut- cline. (for dual clutch transmission)
ting down the engine, when the vehi-
cle is at a standstill (i.e. red stop light,
stop sign, and traffic jam). i Information
The engine is automatically started ٻType A
upon satisfying the starting condi-
tions.
The ISG system is always active,
when the engine is running.
i Information
When the engine is automatically
started by the ISG system, some warn-
OQXI059008
ing lights (i.e. ABS, ESC, ESC OFF,
EPS, and parking brake warning light) ٻType B
may illuminate for a few seconds due
to the low battery voltage. However, it
does not indicate a malfunction with
the ISG system.
7-42
07
Auto stop i Information
The driving speed must reach at least 8
km/h (5 mph) after an idle stop to stop
the engine in idle stop mode again.
The auto stop indicator ( ) illumi- The message, “Auto Stop deactivat-
nates in green on the instrument clus- ed. Start manually”, appears on the
ter, when the engine stops. LCD display with a beep sound.
7-43
Driving your vehicle
7-44
07
To deactivate the ISG system
• Press the ISG OFF button to deac-
tivate the ISG system. Then, the
ISG OFF button indicator illumi-
nates, and the message “Auto
Stop System Off” appears on the
LCD display.
• Press the ISG OFF button again to
reactivate the ISG system. Then,
OGB054013
the ISG OFF button indicator turns
OFF.
The auto start is temporarily deacti-
vated in the following situations.
Manual transmission vehicle ISG system malfunction
When the gear is shifted without the The ISG system may not operate:
clutch pedal depressed. A message When there is a malfunction with the
“Press clutch pedal for Auto Start” will ISG sensors or the ISG system.
appear on the LCD display. To acti-
vate auto start, shift to neutral and
depress the clutch pedal. The followings occur, when there is
a malfunction with the ISG system:
• The auto stop indicator ( ) will
blink in yellow on the instrument
cluster.
• The light on the ISG OFF button
will illuminate.
i Information
• When you cannot turn OFF the ISG
OFF button indicator by pressing
OGB058040 the ISG OFF button, or when the
Dual clutch transmission vehicle malfunction with the ISG system
When the shift lever is shifted from N persists, we recommend that you
(Neutral) to R (Reverse), D (Drive) or contact an authorized HYUNDAI
Manual shift mode without the brake dealer.
pedal depressed. A message “Press • You can turn off the ISG OFF but-
brake pedal for Auto Start” will ap- ton indicator by driving over 80
pear on the LCD display. To activate km/h (50 mph) for up to 2 hours
auto start, depress the brake pedal. with the fan speed below the 2nd po-
sition. If the ISG OFF button indica-
tor remains ON, we recommend
that you contact an authorized
HYUNDAI dealer.
7-45
Driving your vehicle
7-46
07
&58,6(&21752/ǣ,)(48,33('Ǥ
Cruise Control operation • Do not use the Cruise Control
when it may be unsafe to keep
the vehicle at a constant speed:
- When driving in heavy traffic or
when traffic conditions make it
difficult to drive at a constant
speed
- When driving on rainy, icy, or
snow-covered roads
- When driving on hilly or wind-
ing roads
OQXI059011
1. Cruise indicator - When driving in windy areas
2. Set speed • Do not use cruise control when
towing a trailer.
7-47
Driving your vehicle
OQXI059012
1. Press the CRUISE button on the
steering wheel to turn the system
on. The cruise indicator will illumi-
nate.
2. Accelerate to the desired speed,
which must be more than 30 km/h
(20 mph). OQXI059014
OQXI059013
7-48
07
To decrease Cruise Control Cruise Control will be canceled
speed when:
OQXI059013 OQXI059015
• Push the toggle switch down (SET-), • Depressing the brake pedal.
and release it immediately. The • Depressing the clutch pedal.
cruising speed will decrease by 1 (for manual transmission vehicle)
km/h (1 mph) each time you move
the toggle switch down in this man- • Pressing the CANCEL button lo-
ner. cated on the steering wheel.
• Push the toggle switch down (SET-), • Pressing the CRUISE button.
and hold it. Your vehicle set speed Both the cruise indicator and the
will decrease by 10 km/h (5 mph). SET indicator or set speed will turn
Release the toggle switch at the off.
speed you want. • Moving the shift lever into N (Neu-
• Lightly tap the brake pedal. When tral). (for dual clutch transmission
the vehicle attains the desired vehicle)
speed, push the toggle switch • Decreasing the vehicle speed to
down (SET-). less than approximately 30 km/h
(20 mph).
To temporarily accelerate with • The ESC (Electronic Stability Con-
the Cruise Control ON trol) is operating.
Depress the accelerator pedal. When • Downshifting to the 2nd gear in
you take your foot off the accelerator, manual shift mode. (for dual clutch
the vehicle will return to the previous- transmission vehicle)
ly set speed.
If you push the toggle switch down
(SET-) at the increased speed, the
Cruise Control will maintain the in-
creased speed.
7-49
Driving your vehicle
OQXI059014
7-50
07
63(&,$/'5,9,1*&21',7,216
Hazardous driving conditions To prevent transmission wear, wait
When hazardous driving conditions until the wheels stop spinning before
are encountered such as water, shifting gears. Release the accelera-
snow, ice, mud or sand: tor pedal while shifting, and press
lightly on the accelerator pedal while
Drive cautiously and allow extra dis- the transmission is in gear. Slowly
tance for braking. spinning the wheels in forward and
Avoid sudden movements in braking reverse directions causes a rocking
or steering. motion that may free the vehicle.
If stuck in snow, mud, or sand, use
second gear. Accelerate slowly to
avoid spinning the drive wheels. NOTICE
If the tires spin at high speed the
tires can explode, and you or oth-
WARNING ers may be injured. Do not attempt
this procedure if people or objects
Downshifting with a duel clutch
are anywhere near the vehicle.
transmission, while driving on
slippery surfaces can cause an ac- The vehicle can overheat causing
cident. The sudden change in tire an engine compartment fire or oth-
speed could cause the tires to er damage. Spin the wheels as lit-
skid. Be careful when downshift- tle as possible and avoid spinning
ing on slippery surfaces. the wheels at speeds over 56 km/h
(35 mph) as indicated on the
speedometer.
Use sand, rock salt, or other non-slip
material under the drive wheels to
provide traction when stalled in ice, NOTICE
snow, or mud. If you are still stuck after rocking
the vehicle a few times, have the
Rocking the vehicle vehicle pulled out by a tow vehicle
to avoid engine overheating, pos-
If it is necessary to rock the vehicle to sible damage to the transmission,
free it from snow, sand, or mud, first and tire damage. See “Towing” in
turn the steering wheel right and left chapter 6.
to clear the area around your front
wheels. Then, shift back and forth be-
tween 1st and R (Reverse, for manu-
al transmission vehicle) or R (Re-
verse) and a forward gear (for duel
clutch transmission vehicle). Try to
avoid spinning the wheels, and do not
race the engine.
7-51
Driving your vehicle
Hydroplaning
If the road is wet enough and you are
going fast enough, your vehicle may
have little or no contact with the road
surface and actually ride on the wa-
ter. The best advice is SLOW DOWN
when the road is wet. The risk of hy-
droplaning increases as the depth of
tire tread decreases, refer to “Tire
Tread” in chapter 7.
7-52
07
Driving in flooded areas
Avoid driving through flooded areas
unless you are sure the water is no
higher than the bottom of the wheel
hub. Drive through any water slowly.
Allow adequate stopping distance be-
cause brake performance may be re-
duced.
After driving through water, dry the
brakes by gently applying them sev-
eral times while the vehicle is moving
slowly.
7-53
Driving your vehicle
WINTER DRIVING
Snow or icy conditions i Information
You need to keep sufficient distance
between your vehicle and the vehicle Do not install studded tires without
in front of you. first checking local and municipal reg-
Apply the brakes gently. Speeding, ulations for possible restrictions
rapid acceleration, sudden brake ap- against their use.
plications, and sharp turns are poten-
tially very hazardous practices. Tire chains
During deceleration, use engine
braking to the fullest extent. Sudden
brake applications on snowy or icy
roads may cause skids to occur.
To drive your vehicle in deep snow, it
may be necessary to use snow tires
or to install tire chains on your tires.
Always carry emergency equipment.
Some of the items you may want to
carry include tire chains, tow straps
or chains, a flashlight, emergency OQXI059016
flares, sand, a shovel, jumper cables, Since the sidewalls of radial tires are
a window scraper, gloves, ground thinner than other types of tires, they
cloth, coveralls, a blanket, etc. may be damaged by mounting some
types of tire chains on them. There-
fore, the use of snow tires is recom-
Snow tires mended instead of tire chains. Do not
mount tire chains on vehicles
WARNING equipped with aluminum wheels; if
unavoidable use a wire type chain. If
Snow tires should be equivalent in tire chains must be used, use genu-
size and type to the vehicle’s stan- ine HYUNDAI parts and install the tire
dard tires. Otherwise, the safety chain after reviewing the instructions
and handling of your vehicle may provided with the tire chains. Dam-
be adversely affected. age to your vehicle caused by im-
proper tire chain use is not covered
If you mount snow tires on your vehi- by your vehicle manufacturer’s war-
cle, make sure to use radial tires of ranty.
the same size and load range as the
original tires. Mount snow tires on all
four wheels to balance your vehicle’s
handling in all weather conditions.
The traction provided by snow tires
on dry roads may not be as high as
your vehicle’s original equipment
tires. Check with the tire dealer for
maximum speed recommendations.
7-54
07
WARNING When mounting snow chains, park
the vehicle on level ground away from
The use of tire chains may ad- traffic. Turn on the vehicle Hazard
versely affect vehicle handling: Warning Flasher and place a triangu-
• Drive less than 30 km/h (20 mph) lar emergency warning device behind
or the chain manufacturer’s rec- the vehicle (if available). Always
ommended speed limit, which- place the shift lever in neutral, apply
ever is lower. the parking brake and turn off the en-
gine before installing snow chains.
• Drive carefully and avoid bumps,
holes, sharp turns, and other
road hazards, which may cause NOTICE
the vehicle to bounce. When using tire chains:
• Avoid sharp turns or locked • Wrong size chains or improperly
wheel braking. installed chains can damage
your vehicle’s brake lines, sus-
i Information pension, body and wheels.
• Use SAE “S” class or wire
• Install tire chains on the front tires. chains.
It should be noted that installing tire
• If you hear noise caused by
chains on the tires will provide a
chains contacting the body, re-
greater driving force, but will not
tighten the chain to prevent con-
prevent side skids.
tact with the vehicle body.
• Do not install tire chains without
• To prevent body damage, re-
first checking local and municipal
tighten the chains after driving
regulations for possible restrictions
0.5~1.0 km (0.3~0.6 miles).
against their use.
• Do not use tire chains on vehi-
cles equipped with aluminum
Chain Installation wheels. If unavoidable, use a
When installing tire chains, follow the wire type chain.
manufacturer’s instructions and • Use wire chains less than 12 mm
mount them as tightly possible. Drive (0.47 in) wide to prevent damage
slowly (less than 30 km/h (20 mph)) to the chain’s connection.
with chains installed. If you hear the
chains contacting the body or chas-
sis, stop and tighten them. If they still
make contact, slow down until the
noise stops. Remove the tire chains
as soon as you begin driving on
cleared roads.
7-55
Driving your vehicle
7-56
07
Don’t let your parking brake Don’t place foreign objects or
freeze materials in the engine compart-
Under some conditions your parking ment
brake can freeze in the engaged po- Placement of foreign objects or mate-
sition. This is most likely to happen rials which prevent cooling of the en-
when there is an accumulation of gine, in the engine compartment, may
snow or ice around or near the rear cause a failure or combustion. The
brakes or if the brakes are wet. If manufacturer is not responsible for
there is a risk the parking brake may the damage caused by such place-
freeze, apply it only temporarily while ment.
you put the shift lever in P (for duel
clutch transmission) or in first or re-
verse gear (for manual transmission)
and block the rear wheels so the ve-
hicle cannot roll. Then release the
parking brake.
7-57
Driving your vehicle
VEHICLE WEIGHT
Two labels on your driver’s door sill GVW (Gross Vehicle Weight)
show how much weight your vehicle This is the Base Curb Weight plus ac-
was designed to carry: the Tire and tual Cargo Weight plus passengers.
Loading Information Label and the
Certification Label.
Before loading your vehicle, familiar- GVWR (Gross Vehicle Weight Rat-
ize yourself with the following terms ing)
for determining your vehicle’s weight This is the maximum allowable weight
ratings, from the vehicle’s specifica- of the fully loaded vehicle (including
tions and the Certification Label: all options, equipment, passengers
and cargo). The GVWR is shown on
the Certification Label located on the
Base Curb Weight driver’s door sill.
This is the weight of the vehicle in-
cluding a full tank of fuel and all stan-
dard equipment. It does not include Overloading
passengers, cargo, or optional equip-
ment. WARNING
The Gross Axle Weight Rating
Vehicle Curb Weight
(GAWR) and the Gross Vehicle
This is the weight of your new vehicle Weight Rating (GVWR) for your ve-
when you picked it up from your deal- hicle are on the Certification Label
er plus any aftermarket equipment. attached to the driver’s (or front
passenger’s) door. Exceeding
Cargo Weight these ratings can cause an acci-
dent or vehicle damage. You can
This figure includes all weight added calculate the weight of your load
to the Base Curb Weight, including by weighing the items (and people)
cargo and optional equipment. before putting them in the vehicle.
Be careful not to overload your ve-
GAW (Gross Axle Weight) hicle.
This is the total weight placed on
each axle (front and rear) - including
vehicle curb weight and all payload.
7-58
8. What to do in an emergency
8-2
08
IF THE ENGINE WILL NOT
If you have a flat tire while driv- START
ing
If the engine doesn’t turn over
If a tire goes flat while you are driving: or turns over slowly
• Take your foot off the accelerator • Be sure the shift lever is in N (Neu-
pedal and let the vehicle slow tral) or P (Park) if it is a duel clutch
down while driving straight ahead. transmission vehicle. The engine
Do not apply the brakes immedi- starts only when the shift lever is in
ately or attempt to pull off the road N (Neutral) or P (Park).
as this may cause loss of vehicle
control resulting in an accident. • Check the battery connections to
When the vehicle has slowed to be sure they are clean and tight.
such a speed that it is safe to do • Turn on the interior light. If the light
so, brake carefully and pull off the dims or goes out when you operate
road. Drive off the road as far as the starter, the battery is drained.
possible and park on firm, level Do not push or pull the vehicle to start
ground. If you are on a divided it. This could cause damage to your
highway, do not park in the median vehicle.
area between the two traffic lanes.
• When the vehicle is stopped, press
the hazard warning flasher button, See instructions for “Jump
move the shift lever into P (Park, Starting” provided in this chapter.
for duel clutch transmission vehi-
cle) or neutral (for manual trans- WARNING
mission vehicle), apply the parking
brake, and place the ignition switch Push or pull starting the vehicle
in the LOCK/OFF position. may cause the catalytic converter
• Have all passengers get out of the to overload which can lead to dam-
vehicle. Be sure they all get out on age to the emission control sys-
the side of the vehicle that is away tem.
from traffic.
• When changing a flat tire, follow If the engine turns over nor-
the instructions provided later in mally but doesn’t start
this chapter.
• Check the fuel level and add fuel if
necessary.
If the engine still does not start, we
recommend that you call an autho-
rized HYUNDAI dealer for assistance.
8-3
What to do in an emergency
JUMP STARTING
Jump starting can be dangerous if If acid gets into your eyes, flush
done incorrectly. Follow the jump your eyes with clean water for at
starting procedure in this section to least 15 minutes and get immedi-
avoid serious injury or damage to ate medical attention. If acid gets
your vehicle. If in doubt about how to on your skin, thoroughly wash the
properly jump start your vehicle, we area. If you feel pain or a burning
strongly recommend that you have a sensation, get medical attention
service technician or towing service immediately.
do it for you. • When lifting a plastic-cased bat-
tery, excessive pressure on the
WARNING case may cause battery acid to
leak. Lift with a battery carrier or
To prevent SERIOUS INJURY or with your hands on opposite
DEATH to you or bystanders, al- corners.
ways follow these precautions • Do not attempt to jump start
when working near or handling the your vehicle if your battery is
battery: frozen.
Always read and follow • NEVER attempt to recharge the
instructions carefully when battery when the vehicle’s bat-
handling a battery. tery cables are connected to the
Wear eye protection de- battery.
signed to protect the eyes • The electrical ignition system
from acid splashes. works with high voltage. NEVER
Keep all flames, sparks, or touch these components with
smoking materials away the engine running or when the
from the battery. ignition switch is in the ON posi-
Hydrogen is always pres- tion.
ent in battery cells, is high- • Do not allow the (+) and (-) jump-
ly combustible, and may er cables to touch. It may cause
explode if ignited. sparks.
Keep batteries out of reach • The battery may rupture or ex-
of children. plode when you jump start with
a low or frozen battery.
Batteries contain sulfuric • Never attempt jump start if you
acid which is highly corro- observe cracks, leaks or other
sive. Do not allow acid to damage on Battery.
contact your eyes, skin or
clothing.
8-4
08
CAUTION Jump starting procedure
1. Position the vehicles close enough
• Improper jump starting proce- that the jumper cables will reach,
dure can result in battery explo- but do not allow the vehicles to
sion and acid burn hazard. touch.
• Loosely connected battery ca- 2. Avoid fans or any moving parts in
bles could damage the electron- the engine compartment at all
ic control units. times, even when the vehicles are
• To disconnect battery terminals turned off.
wait for at least 2 minutes to al- 3. Turn off all electrical devices such
low discharge of high voltage or as radios, lights, air conditioning,
it could lead to personal injury. etc. Put the vehicles in P (Park, for
• While disconnecting, always duel clutch transmission vehicle)
disconnect the -VE terminal first or neutral (for manual transmission
and while connecting, always vehicle), and set the parking
connect the -VE terminal last. brakes. Turn both vehicles OFF.
i
OQXI069002
Information 4. Connect the jumper cables in the
An inappropriately disposed exact sequence shown in the illus-
battery can be harmful to the tration. First connect one jumper
environment and human cable to the red, positive (+) jump-
Pb
health. Dispose the battery ac- er terminal of your vehicle (1).
cording to your local law(s) or 5. Connect the other end of the jump-
regulation. er cable to the red, positive (+) bat-
tery/jumper terminal of the assist-
ing vehicle (2).
6. Connect the second jumper cable
to the black, negative (-) battery/
chassis ground of the assisting ve-
hicle (3).
8-5
What to do in an emergency
7. Connect the other end of the sec- Disconnect the jumper cables in the
ond jumper cable to the black, neg- exact reverse order you connected
ative (-) chassis ground of your ve- them:
hicle (4). 1. Disconnect the jumper cable from
Do not allow the jumper cables to the black, negative (-) chassis
contact anything except the correct ground of your vehicle (4).
battery or jumper terminals or the 2. Disconnect the other end of the
correct ground. Do not lean over jumper cable from the black, nega-
the battery when making connec- tive (-) battery/chassis ground of
tions. the assisting vehicle (3).
8. Start the engine of the assisting 3. Disconnect the second jumper ca-
vehicle and let it run at approxi- ble from the red, positive (+) bat-
mately 2,000 rpm for a few min- tery/jumper terminal of the assist-
utes. Then start your vehicle. ing vehicle (2).
4. Disconnect the other end of the
If your vehicle will not start after a few jumper cable from the red, positive
attempts, it probably requires servic- (+) jumper terminal of your vehicle
ing. In this event please seek quali- (1).
fied assistance. If the cause of your
battery discharging is not apparent,
we recommend that your vehicle be
checked by an authorized HYUNDAI
dealer.
WARNING
Never connect Jumper Cable di-
rectly to the negative (-) terminal of
discharged Battery (Your Vehicle
Battery), or an Explosion may oc-
cur.
8-6
08
IF THE ENGINE OVERHEATS
If your temperature gauge indicates 4. Check for coolant leaking from the
overheating, you experience a loss of radiator, hoses or under the vehi-
power, or hear loud pinging or knock- cle. (If the air conditioning had
ing, the engine may be overheating. If been in use, it is normal for cold
this happens, you should: water to be draining from it when
1. Pull off the road and stop as soon you stop.)
as it is safe to do so. 5. If engine coolant is leaking out,
2. Place the shift lever in P (Park, for stop the engine immediately and
duel clutch transmission vehicle) we recommend that you call an au-
or neutral (for manual transmission thorized HYUNDAI dealer for as-
vehicle) and set the parking brake. sistance.
If the air conditioning is ON, turn it
OFF. WARNING
3. If engine coolant is running out un-
der the vehicle or steam is coming NEVER remove the radi-
out from the hood, stop the engine. ator cap or the drain
Do not open the hood until the plug while the engine
coolant has stopped running or the and radiator are hot. Hot
steaming has stopped. If there is coolant and steam may
no visible loss of engine coolant blow out under pressure, causing
and no steam, leave the engine serious injury.
running and check to be sure the Turn the engine off and wait until
engine cooling fan is operating. If the engine cools down. Use ex-
the fan is not running, turn the en- treme care when removing the ra-
gine off. diator cap. Wrap a thick towel
around it, and turn it counterclock-
wise slowly to the first stop. Step
WARNING back while the pressure is released
While the engine is run- from the cooling system. When
ning, keep hands, cloth- you are sure all the pressure has
ing and tools away from been released, press down on the
the moving parts such cap, using a thick towel, and con-
as the cooling fan and tinue turning counterclockwise to
drive belt to prevent se- remove it.
rious injury.
8-7
What to do in an emergency
NOTICE
• Serious loss of coolant indi-
cates a leak in the cooling sys-
tem and we recommend the sys-
tem be checked by an authorized
HYUNDAI dealer.
• When the engine overheats from
low engine coolant, suddenly
adding engine coolant may
cause cracks in the engine. To
prevent damage, add engine
coolant slowly in small quanti-
ties.
8-8
08
7,5(35(6685(021,725,1*6<67(0ǣ7306Ǥǣ,)(48,33('Ǥ
Please note that the TPMS is not a
substitute for proper tire mainte-
nance, and it is the driver’s responsi-
bility to maintain correct tire pressure,
even if under-inflation has not
reached the level to trigger illumina-
tion of the TPMS low tire pressure
telltale.
Your vehicle has also been equipped
with a TPMS malfunction indicator to
OQXI069003
indicate when the system is not oper-
Low tire pressure telltale / ating properly. The TPMS malfunc-
TPMS malfunction indicator tion indicator is combined with the
low tire pressure telltale. When the
system detects a malfunction, the
Each tire, including the spare (if pro- telltale will flash for approximately
vided), should be checked monthly one minute and then remain continu-
when cold and inflated to the inflation ously illuminated. This sequence will
pressure recommended by the vehi- continue upon subsequent vehicle
cle manufacturer on the vehicle plac- start-ups as long as the malfunction
ard or tire inflation pressure label. (If exists. When the malfunction indica-
your vehicle has tires of a different tor is illuminated, the system may not
size than the size indicated on the ve- be able to detect or signal low tire
hicle placard or tire inflation pressure pressure as intended. TPMS mal-
label, you should determine the prop- functions may occur for a variety of
er tire inflation pressure for those reasons, including the installation of
tires.) replacement or alternate tires or
As an added safety feature, your ve- wheels on the vehicle that prevent
hicle has been equipped with a tire the TPMS from functioning properly.
pressure monitoring system (TPMS) Always check the TPMS malfunction
that illuminates a low tire pressure telltale after replacing one or more
telltale when one or more of your tires tires or wheels on your vehicle to en-
is significantly under-inflated. sure that the replacement or alternate
Accordingly, when the low tire pres- tires and wheels allow the TPMS to
sure telltale illuminates, you should continue to function properly.
stop and check your tires as soon as
possible, and inflate them to the prop-
er pressure. Driving on a significantly i Information
under-inflated tire causes the tire to If the TPMS indicator does not illumi-
overheat and can lead to tire failure. nate for 3 seconds when the ignition
Under-inflation also reduces fuel effi- switch is turned to the ON position or
ciency and tire tread life, and may af- engine is running, or if it comes on af-
fect the vehicle’s handling and stop- ter blinking for approximately one
ping ability. minute, we recommend that you con-
tact an authorized HYUNDAI dealer.
8-9
What to do in an emergency
8-10
08
TPMS (Tire Pressure Changing a tire with TPMS
Monitoring System) If you have a flat tire, the Low Tire
malfunction indicator Pressure will come on. We recom-
mend that the flat tire be checked by
an authorized HYUNDAI dealer.
The TPMS malfunction indicator will
illuminate after it blinks for approxi-
mately one minute when there is a NOTICE
problem with the Tire Pressure Moni-
toring System. If the system is able to We recommend that you use a
correctly detect an under inflation puncture-repairing agent approved
warning at the same time as system by HYUNDAI.
failure then it will illuminate the TPMS The sealant on the tire pressure
malfunction indicator. sensor and wheel shall be elemi-
We recommend that the system be nated when you replace the tire
checked by an authorized HYUNDAI with a new one.
dealer.
Each wheel is equipped with a tire
pressure sensor mounted inside the
NOTICE tire behind the valve stem. You must
• The TPMS malfunction indicator use TPMS specific wheels. It is rec-
may be illuminated if the vehicle ommended that you have your tires
is moving around electric power serviced by an authorized HYUNDAI
supply cables or radios trans- dealer.
mitter such as at police stations, Even if you replace the low pressure
government and public offices, tire with the spare tire, the Low Tire
broadcasting stations, military Pressure Telltale will blink or remain
installations, airports, or trans- on until the low pressure tire is re-
mitting towers, etc. This can in- paired and placed on the vehicle.
terfere with normal operation of
the Tire Pressure Monitoring After you replace the low pressure
System (TPMS). tire with the spare tire, the Low Tire
Pressure Telltale may blink or illumi-
• The TPMS malfunction indicator nate after a few minutes because the
may illuminate if snow chains or TPMS sensor mounted on the spare
some separately purchased de- wheel is not initiated.
vices such as notebook comput-
ers, mobile charger, remote Once the low pressure tire is re-in-
starter, navigation etc. are used flated to the recommended pressure
in the vehicle. This can interfere and installed on the vehicle or the
with normal operation of the Tire new TPMS sensor mounted on the
Pressure Monitoring System wheel, the TPMS malfunction indica-
(TPMS). tor and the low tire pressure and posi-
tion telltales will turn off within a few
minutes of driving.
8-11
What to do in an emergency
8-12
08
IF YOU HAVE A FLAT TIRE
WARNING Removing and storing the
spare tire
Changing a tire can be dangerous.
Follow the instructions in this sec-
tion when changing a tire to reduce
the risk of serious injury or death.
OQXI069005
8-13
What to do in an emergency
in the vehicle while it is on the 6. Loosen the wheel lug nuts counter-
jack. clockwise one turn each in the or-
• Keep children away from the der shown above, but do not re-
road and the vehicle. move any lug nuts until the tire has
been raised off of the ground.
8-14
08
10. Install the spare tire onto the
studs of the hub.
11. Tighten the lug nuts with your fin-
gers onto the studs with the small-
er end of the lug nuts closest to
the wheel.
12. Lower the vehicle to the ground
by turning the jack handle coun-
terclockwise.
OQXI069008
OQXI069010
8-15
What to do in an emergency
If you have a tire gauge, check the Use of compact spare tires
tire pressure (see “Tires and Wheels” (if equipped)
in chapter 8 for tire pressure instruc- Compact spare tires are designed for
tions.). If the pressure is lower or emergency use only. Drive carefully
higher than recommended, drive on the compact spare tire and always
slowly to the nearest service station follow the safety precautions.
and adjust it to the recommended
pressure. Always reinstall the valve
cap after checking or adjusting tire WARNING
pressure. If the cap is not replaced,
air may leak from the tire. If you lose To prevent compact spare tire fail-
a valve cap, buy another and install it ure and loss of control possibly
as soon as possible. After changing resulting in an accident:
tires, secure the flat tire and return • Use the compact spare tire only
the jack and tools to their proper stor- in an emergency.
age locations. • NEVER operate your vehicle
over 80 km/h (50 mph).
i Information • Do not exceed the vehicle’s
maximum load rating or the load
Check the tire pressure as soon as pos- carrying capacity shown on the
sible after installing a spare tire. Ad- sidewall of the compact spare
just it to the recommended pressure. tire.
• Do not use the compact spare
NOTICE tire continuously. Repair or re-
place the original tire as soon as
Your vehicle has metric threads on possible to avoid failure of the
the studs and lug nuts. Make cer- compact spare tire.
tain during tire changing that the
same nuts that were removed are
reinstalled. If you have to replace
your lug nuts make sure they have
metric threads to avoid damaging
the studs and ensure the wheel is
properly secured to the hub. We
recommend that you consult an
authorized HYUNDAI dealer for as-
sistance.
8-16
08
When driving with the compact spare
NOTICE
tire mounted to your vehicle:
• Check the tire pressure after in- To prevent damaging the compact
stalling the compact spare tire. The spare tire and your vehicle:
compact spare tire should be in- • Drive slowly enough for the road
flated to 420 kPa (60 psi). conditions to avoid all hazards,
• Do not take this vehicle through an such as a potholes or debris.
automatic car wash while the com- • Avoid driving over obstacles.
pact spare tire is installed. The compact spare tire diameter
• Do not use the compact spare tire is smaller than the diameter of a
on any other vehicle because this conventional tire and reduces
tire has been designed especially the ground clearance approxi-
for your vehicle. mately 25 mm (1 inch).
• The compact spare tire’s tread life • Do not use tire chains on the
is shorter than a regular tire. In- compact spare tire. Because of
spect your compact spare tire reg- the smaller size, a tire chain will
ularly and replace worn compact not fit properly.
spare tires with the same size and • Do not use the compact spare
design, mounted on the same tire on any other wheels, nor
wheel. should standard tires, snow
• Do not use more than one compact tires, wheel covers or trim rings
spare tire at a time. be used with the compact spare
wheel.
• Do not tow a trailer while the com-
pact spare tire is installed.
i Information
When the original tire and wheel are
repaired and reinstalled on the vehicle,
the lug nut torque must be set correctly
to prevent wheel vibration. The correct
lug nut tightening torque is 11~13
kgf.m (79~94 lbf.ft).
8-17
What to do in an emergency
Jack label
ٻExample
• Type A
OHYK065010
• Type B
OHYK065011
ٻThe actual Jack label in the vehicle may differ from the illustration.
For more detailed specifications, refer to the label attached to the jack.
8-18
08
TOWING
Towing service
OQXI069012
Dolly
Dolly OQXI069013
OQXI069011
8-19
What to do in an emergency
NOTICE
Failure to place the shift lever in N
(Neutral) when being towed with OQXI069016
the front wheels on the ground can
cause internal damage to the If towing is necessary, we recom-
transmission. mend you have it done by an autho-
rized HYUNDAI dealer or a commer-
cial tow truck service.
Removable towing hook
OQXI069015
OQXI069017
1. Open the tailgate, and remove the If towing service is not available in an
towing hook from the tool case. emergency, your vehicle may be tem-
2. Remove the hole cover pressing porarily towed using a cable or chain
the lower part of the cover on the secured to the emergency towing
front bumper. hook at the front (or rear) of the vehi-
3. Install the towing hook by turning it cle.
clockwise into the hole until it is ful- Use extreme caution when towing the
ly secured. vehicle with a cable or chain. A driver
4. Remove the towing hook and in- must be in the vehicle to steer it and
stall the cover after use. operate the brakes.
Towing in this manner may be done
only on hard-surfaced roads for a
short distance and at low speeds.
Also, the wheels, axles, power train,
steering and brakes must all be in
good condition.
8-20
08
Always follow these emergency tow-
ing precautions:
• Place the ignition switch in the
ACC position so the steering wheel
is not locked.
• Place the shift lever in N (Neutral).
• Release the parking brake.
• Depress the brake pedal with more
force than normal since you will
have reduced braking perfor- OQXI069018
EMERGENCY COMMODITY
Your vehicle is equipped with emer-
gency commodities to help you re-
spond to emergency situation.
Triangle reflector
Place the triangle reflector on the
road to warn oncoming vehicles
during emergencies, such as when
the vehicle is parked by the roadside
due to problems.
8-22
9. Maintenance
The actual engine room in the vehicle may differ from the illustration.
OQXI079001/OQXI079100
-3
Maintenance
The actual engine room in the vehicle may differ from the illustration.
OQXI079002
9-4
09
MAINTENANCE SERVICES
You should exercise the utmost care Owner maintenance precau-
to prevent damage to your vehicle tions
and injury to yourself whenever per- Improper or incomplete service may
forming any maintenance or inspec- result in problems. This chapter gives
tion procedures. Inadequate, incom- instructions only for the maintenance
plete or insufficient servicing may items that are easy to perform.
result in operational problems with
your vehicle that could lead to vehicle
damage, an accident, or personal in- i Information
jury.
Improper owner maintenance during
the warranty period may affect war-
Owner’s responsibility ranty coverage. For details, read the
separate Service Passport provided
i Information
with the vehicle. If you’re unsure about
any servicing or maintenance proce-
Maintenance Service and Record Re- dure, we recommend that the system
tention are the owner’s responsibility. be serviced by an authorized HYUND-
AI dealer.
We recommend in general that you
have your vehicle serviced by an au- WARNING
thorized HYUNDAI dealer.
Maintenance work
You should retain documents that
show proper maintenance has been • Performing maintenance work
performed on your vehicle in accor- on a vehicle can be dangerous.
dance with the scheduled mainte- You can be seriously injured
nance service charts shown on the while performing some mainte-
following pages. You need this infor- nance procedures. If you lack
mation to establish your compliance sufficient knowledge and expe-
with the servicing and maintenance rience or the proper tools and
requirements of your vehicle warran- equipment to do the work, we
ties. recommend that the system be
serviced by an authorized
Detailed warranty information is pro- HYUNDAI dealer.
vided in your Service Passport.
• Working under the hood with
Repairs and adjustments required as the engine running is danger-
a result of improper maintenance or a ous. It becomes even more dan-
lack of required maintenance are not gerous when you wear jewelry
covered when your vehicle is covered or loose clothing. These can be-
by warranty. come entangled in moving parts
and result in injury.
9-5
Maintenance
Therefore, if you must run the • Before touching the battery, ig-
engine while working under the nition cables and electrical wir-
hood, make certain that you re- ing, you should disconnect the
move all jewelry (especially battery “-” terminal. You may
rings, bracelets, watches, and get an electric shock from the
necklaces) and all neckties, electric current.
scarves, and similar loose cloth- • When you remove the interior
ing before getting near the en- trim cover with a flat head (-)
gine or cooling fans. driver, be careful not to damage
the cover.
WARNING • Be careful when you replace and
clean bulbs to avoid burns or
Do not leave gloves, rags or any electrical shock.
other combustible material in the
engine compartment. Doing so
may cause a heat-induced fire. WARNING
Diesel Engine
NOTICE Never work on injection system
• Do not put heavy objects or ap- with engine running or within 30
ply excessive force on top of the seconds after shutting off engine.
engine cover (if equipped) or High-pressure pump, rail, injectors
fuel related parts. and high-pressure pipes are sub-
ject to high pressure even after the
• When you inspect the fuel sys-
engine stopped. The fuel jet pro-
tem (fuel lines and fuel injection
duced by fuel leaks may cause se-
devices), we recommend that
rious injury, if it touches the body.
you contact an authorized
People using pacemakers should
HYUNDAI dealer.
not move more than 30cm closer
• Do not drive long time with the to the ECU or wiring harness with-
engine cover(if equipped) re- in the engine room while engine is
moved. running, since the high currents in
• When checking the engine the electronic engine control sys-
room, do not go near fire. Fuel, tem produce considerable mag-
washer fluid, etc. are flammable netic fields.
oils that may cause fire.
9-6
09
Engine compartment precau-
tions (Diesel engine)
• The injector operates at high volt-
age (maximum 200v). Therefore,
the following accidents may occur.
- Direct contact with the injector or
injector wiring may cause electric
shock or damage your muscle or
nerve system.
- The electromagnetic wave from
the operating injector may cause
the artificial heart pacemaker to
malfunction.
• Follow the safety tips provided be-
low, when you are checking the
engine room while the engine is
running.
- Do not touch the injector, injector
wirings, and the engine computer
while the engine is running.
- Do not remove the injector con-
nector while the engine is running.
- People using pacemakers must
not go near the engine while the
engine is starting or running.
9-7
Maintenance
OWNER MAINTENANCE
The following lists are vehicle checks While operating your vehicle:
and inspections that should be per- • Note any changes in the sound of
formed at the frequencies indicated the exhaust or any smell of ex-
to help ensure safe, dependable op- haust fumes in the vehicle.
eration of your vehicle.
• Check for vibrations in the steering
Any adverse conditions should be wheel. Notice any increased steer-
brought to the attention of your dealer ing effort or looseness in the steer-
as soon as possible. ing wheel, or change in its straight-
These Owner Maintenance Checks ahead position.
are generally not covered by warran- • Notice if your vehicle constantly
ties and you may be charged for la- turns slightly or “pulls” to one side
bor, parts and lubricants used. when traveling on smooth, level
road.
Owner maintenance schedule • When stopping, listen and check
When you stop for fuel: for unusual sounds, pulling to one
side, increased brake pedal travel
• Check the engine oil level. or “hard-to-push” brake pedal.
• Check the coolant level in coolant • If any slipping or changes in the
reservoir. operation of your transmission oc-
• Check the windshield washer fluid curs, check the transmission fluid
level. level.
• Look for low or under-inflated tires. • Check dual clutch transmission P
• Check the radiator and condenser. (Park) function.
Check if the front of the radiator • Check the parking brake.
and condenser are clean and not • Check for fluid leaks under your
blocked with leaves, dirt or insects vehicle (water dripping from the air
etc. conditioning system during or after
If any of the above parts are ex- use is normal).
tremely dirty or you are not sure of
their condition, we recommend
that you contact an authorized
HYUNDAI dealer.
WARNING
Be careful when checking your en-
gine coolant level when the engine
is hot. Scalding hot coolant and
steam may blow out under pres-
sure. This could cause burns or
other serious injury.
9-8
09
At least monthly: At least once a year:
• Check the coolant level in the en- • Clean the body and door drain
gine coolant reservoir. holes.
• Check the operation of all exterior • Lubricate the door hinges and
lights, including the stoplights, turn checks, and hood hinges.
signals and hazard warning flash- • Lubricate the door and hood locks
ers. and latches.
• Check the inflation pressures of all • Lubricate the door rubber weather-
tires including the spare for tires strips.
that are worn, show uneven wear,
or are damaged. • Check the air conditioning system.
• Check for loose wheel lug nuts. • Inspect and lubricate dual clutch
transmission linkage and controls.
• Clean the battery and terminals.
At least twice a year • Check the brake/clutch fluid level.
(i.e., every Spring and Fall):
• Check the radiator, heater and air
conditioning hoses for leaks or
damage.
• Check the windshield washer
spray and wiper operation. Clean
wiper blades with clean cloth
dampened with washer fluid.
• Check the headlight alignment.
• Check the muffler, exhaust pipes,
shields and clamps.
• Check the lap/shoulder belts for
wear and function.
9-9
Maintenance
If your vehicle is operated under the above conditions, you should inspect, re-
place or refill more frequently than the following Normal Maintenance Sched-
ule. After the periods or distance shown in the chart, continue to follow the
prescribed maintenance intervals.
9-10
Maintenance
1250$/0$,17(1$1&(6&+('8/()253(752/ ',(6(/(1*,1(
#HECK THE ENGINE OIL LEVEL AND LEAK EVERY KM MILES OR BEFORE STARTING A