Beruflich Dokumente
Kultur Dokumente
mentioned
section 900 in MoRT&H and as per provision mentioned in Concession Agreement. The summary list is enclosed as
Annex-A.
QUALITY REVIEW REPORT (O & M Period ) Ch. 263+000 to 502+000 , AUGUST. 2014
Nos. of Test Conducted by IC
Sr No. Name of Test Frequency of Test Specification Requirement Up To Previous Month In This Month
Passed Failed Passed Failed Total
OGL
1 FREE SWELL INDEX As Required 50% Max. 00 00 00 00 00
3
2 PLASTICITY TEST 2 Test / 3000 M LL < 70 & PI < 45 00 00 00 00 00
3
3 MAX. DRY DENSITY TEST 2 Test / 3000 M 00 00 00 00 00
3
4 GRAIN SIZE ANALYSIS 2 Test / 3000 M 00 00 00 00 00
3
5 CBR 1 Test / 3000 M 00 00 00 00 00
2
6 FDD 1 Test / 1000 M Min. 95% 00 00 00 00 00
EXISTING SHOULDER
1 FREE SWELL INDEX As Required 50% Max. 00 00 00 00 00
3
2 GRAIN SIZE ANALYSIS 2 Test / 3000 M 00 00 00 00 00
3
3 PLASTICITY TEST 2 Test / 3000 M LL < 70 & PI < 45 00 00 00 00 00
4 MAX. DRY DENSITY TEST 2 Test / 3000 M3 Min. 1.75 gm/cc 00 00 00 00 00
3
5 CBR 1 Test / 3000 M Min. 8% 00 00 00 00 00
2
6 FDD 1 Test / 1000 M Min. 97% 00 00 00 00 00
7 DELETERIOUS CONTENT As Required 00 00 00 00 00
EMBANKMENT/SUB‐GRADE
1 FREE SWELL INDEX As Required Max 50% 14 00 00 00 14
2 GRAIN SIZE ANALYSIS 2 Test / 3000 M3 14 00 00 00 14
3 PLASTICITY TEST 2 Test / 3000 M3 LL < 70 & PI < 45 14 00 00 00 14
3
4 MAX. DRY DENSITY TEST 2 Test / 3000 M As per MORTH &H Table No. 300‐1. 14 00 00 00 14
3
5 CBR 1 Test / 3000 M Min. 8% 14 00 00 00 14
Min. 95% for Embankment and Min.
6 FDD 1 Test / 1000 M2 for EMBK. & 1 Test / 500 M2 for Subgrade 47 00 00 00 47
97% for Subgrade.
SIDE SHOULDER
2
1 FDD 1 Test / 500 M Min. 97% 00 00 00 00 00
RE WALL MATERIAL
3
1 GRADATION 2 Test / 3000 M As per Drawing 03 00 00 00 03
3
2 PLASTICITY INDEX 2 Test / 3000 M As per Drawing 03 00 00 00 03
3
3 MAX. DRY DENSITY TEST 2 Test / 3000 M As per Drawing 03 00 00 00 03
3
2 FLAKINESS & ELONGATION INDEX 1 Test / 50 M of Aggregate Min. 30% 00 00 00 00 00
Initially one set of 3 representative specimen for each source of
3 STRIPPING VALUE TEST Min. 95% 00 00 00 00 00
supply. Subsequently when warranted by changes in the quality
SOUNDNESS TEST (MAGNESIUM & Initially , one determination by each method for each souce of Sodium Sulpahte Max. 12% and
4 00 00 00 00 00
SODIUM SULPHATE) supply, then as warranted by change in the quality of Magnesium Sulphate Max. 18%
WATER ABSORPTION & Initially one set of 3 representative specimens for each source of
5 Max. 2% 00 00 00 00 00
SP. GRAVITY TEST supply. Subsequently when warranted by changes in the quality
6 SAND EQUIVALENT TEST As Required Min. 50 00 00 00 00 00
2
12 TACK COAT One test per 500 M and not less than two tests per day. 0.25 to 0.3 kg/M2 00 00 00 00 00
DBM
3
1 AGG. IMPACT VALUE TEST 1 Test / 50 M of Aggregate Min. 27% 55 00 00 00 55
3
2 FLAKINESS & ELONGATION INDEX 1 Test / 50 M of Aggregate Min. 30% 55 00 00 00 55
Initially one set of 3 representative specimen for each source of
3 STRIPPING VALUE TEST Min. 95% 00 00 00 00 00
supply. Subsequently when warranted by changes in the quality
Nos. of Test Conducted by IC
Sr No. Name of Test Frequency of Test Specification Requirement Up To Previous Month In This Month
Passed Failed Passed Failed Total
SOUNDNESS TEST (MAGNESIUM & Initially , one determination by each method for each souce of Sodium Sulpahte Max. 12% and
4 00 00 00 00 00
SODIUM SULPHATE) supply, then as warranted by change in the quality of Magnesium Sulphate Max. 18%
Initially one set of 3 representative specimens for each source of
WATER ABSORPTION &
5 supply. Subsequently when warranted by changes in the quality Max. 2% 00 00 00 00 00
SP. GRAVITY TEST
of aggregates.
2
16 TACK COAT One test per 500 M and not less than two tests per day. 0.25 to 0.3 kg/M2 39 00 00 00 39
Number of samples per lot and tests as per IS:73,IS:217 and
17 QUALITY OF BINDER (SS) 20‐100 Sec. 02 00 00 00 02
IS:8887 as applicable.
BC
3
1 AGG. IMPACT VALUE TEST 1 Test / 50 M of Aggregate Max. 24% 30 00 00 00 30
3
2 FLAKINESS & ELONGATION INDEX 1 Test / 50 M of Aggregate Max. 30% 31 00 00 00 31
Initially one set of 3 representative specimen for each source of
3 STRIPPING VALUE TEST 1 00 00 00 00 00
supply. Subsequently when warranted by changes in the quality
SOUNDNESS TEST (MAGNESIUM & Initially , one determination by each method for each souce of Sodium Sulpahte Max. 12% and
4 00 00 00 00 00
SODIUM SULPHATE) supply, then as warranted by change in the quality of Magnesium Sulphate Max. 18%
WATER ABSORPTION & SP. Initially one set of 3 representative specimens for each source of
5 Max. 2% 00 00 00 00 00
GRAVITY TEST supply. Subsequently when warranted by changes in the quality
6 SAND EQUIVALENT TEST As Required Min. 50% 00 00 00 00 00
5 VISCOSITY TEST Initially on submission. 00 00 00 00 00
Nos. of Test Conducted by IC
Sr No. Name of Test Frequency of Test Specification Requirement Up To Previous Month In This Month
Passed Failed Passed Failed Total
6 RESIDUE BY EVAPORATION As Required 00 00 00 00 00
Regularly as required subject to minimu of one day a day for
SP. GRAVITY & WATER course aggregates and two tests a day for fine aggregate. This
3 00 00 00 00 00
ABSORPTION OF AGG. data shall be used for correcting the water demand of the mix on
daily basis.
COMPRESSIVE STRENGTH TEST 28
As per MORT &H Table No. 1700‐8 As per grade of concrete. 92 00 09 00 101
DAYS
7
7 DAYS As per MORT &H Table No. 1700‐8 60 00 06 00 66
One test for each dumper load at both batching plant site and
8 WORKABILITY TEST paving site initially when work starts subsequently sampling may As per MORT &H Table no. 1700‐4 05 00 01 00 06
be done from alternate dumper.
9 MOISTURE CONTENT 00 00 00 00 00
DRY LEAN CONCRETE (DLC)
1 SIEVE ANALYSIS OF AGGREGATE 1 TEST/DAY AS PER MOSRT 7 H TABLE 600.1 08 00 00 00 08
COMPRESSIVE STRENGTH TEST 7
2 3 SAMPLE / 1000 Sq.m 10 Mpa Min. 09 00 00 00 09
DAYS
PAVEMENT QUALITY CONCRETE (PQC)
1 28 DAYS CUBE & BEAM TEST As per MORT &H Table No. 900‐6. As per grade of concrete. 19 00 00 00 19
4 Reinforce Steel 00 00 00 00 00
8mm Dia‐Bar 00 00 00 00 00
10mm Dia‐Bar 00 00 00 00 00
12mm Dia‐Bar 01 00 00 00 01
As per Table‐5 of IS 1786‐1990 As per IS 1786 1990
16mm Dia‐Bar 01 00 00 00 01
20mm Dia‐Bar 01 00 00 00 01
25mm Dia‐Bar 01 00 00 00 01
32mm Dia‐Bar 00 00 00 00 00
5 Structutal Steel Plates 00 00 00 00 00
8mm Thick 00 00 00 00 00
10mm Thick 00 00 00 00 00
a) upto 100 ton‐2 samples
12mm Thick b) 100‐200 ton‐3 samples As per IS 2062 1999 00 00 00 00 00
c) over 200 ton‐4 samples
16mm Thick 00 00 00 00 00
25mm Thick 00 00 00 00 00
32mm Thick 00 00 00 00 00
00 00
00 00
00 00
00 00
00 00
00 00
00 00
00 00
00 00
00 00
00 00
00 00
00 00
14 00
14 00
14 00
14 00
14 00
47 00
00 00
03 00
03 00
03 00
01 00
22 00
24 00
24 00
Up To Date
Passed Failed
00 00
00 00
00 00
65 00
00 00
51 00
51 00
51 00
51 00
53 00
00 00
00 00
00 00
00 00
00 00
00 00
00 00
00 00
00 00
00 00
00 00
00 00
55 00
55 00
00 00
Up To Date
Passed Failed
00 00
00 00
00 00
00 00
89 00
55 00
00 00
55 00
57 00
30 00
00 00
32 00
39 00
02 00
30 00
31 00
00 00
00 00
00 00
00 00
00 00
76 00
31 00
Up To Date
Passed Failed
00 00
28 00
25 00
42 00
00 00
41 00
02 00
00 00
00 00
00 00
00 00
23 00
23 00
03 00
23 00
13 00
13 00
02 00
09 00
06 00
13 00
00 00
00 00
00 00
00 00
00 00
Up To Date
Passed Failed
00 00
00 00
49 00
49 00
00 00
00 00
19 00
20 00
101 00
66 00
06 00
00 00
08 00
09 00
00 00
19 00
10 00
05 00
Up To Date
Passed Failed
08 00
07 00
08 00
06 00
06 00
04 00
03 00
05 00
02 00
00 00
00 00
00 00
01 00
01 00
01 00
01 00
00 00
00 00
00 00
00 00
00 00
00 00
00 00
00 00
00 00
00 00