Beruflich Dokumente
Kultur Dokumente
Safety-Walk
Conformable anti-slip surfacing, black ( Ref 510 )
Technical Data
TD 472 B Issue 2 Date : January 02
Supersedes : TD 472 A – July 99
EK. Page 1 / 4
Surface Preparation : face. Note: minimize touching (contami- For extra protection from excessive moisture
Make sure surface is clean, dry, smooth and nating) adhesive with fingers. or liquids (not constant moisture) use 3M
above minimum temperature of application : 4. Continue to remove liner and press firmly Scotch-Seal™ 1103 Clear Sealant to protect
Conformable: 4°C (40°F) in place as liner is removed. the edges of 3M Safety-Walk materials
General Purpose: 4°C (40°F) 5. For small pieces, peel liner off piece. against penetration of liquids.
Resilient Medium: 4°C (40°F) Holding piece by its edges, curve it gently Priming Instructions :
Resilient Fine: 10°C (50°F) with the adhesive side out. Align the mid- 1. Properly clean the floor following “sur-
Repair or replace any damaged or broken dle of the piece over the middle of the tar- face preparation” procedure.
surface. get surface and press down. 2. Use a paint brush and paint on a thin
Remove chipped, cracked or peeled paint 6. Finally press into firm contact with sur- coat of primer where the 3M Safety-
from surface. face using a rubber hand roller by starting Walk materials are to be applied.
Strip waxed floors prior to washing. in middle and rolling out towards edges. 3. Allow the primed area to dry thoroughly
Use appropriate cleaner or solvent wipe to 7. For applying 3M Safety-Walk Conform- (no evidence of stickiness or tackiness)
clean surface : able treads, a soft rubber mallet can also before applying 3M Safety-Walk mate-
be used to ensure product fully conforms rial.
to surface. Pound edges extra hard. Note : Primers are not generally recom-
Type of surface Recommended
preparation
8. On steps, apply 3M Safety-Walk materi- mended with the clear grade because the
Bare metal, Solvent wipe als 12 to 15 mm from stair edge to pre- transparency benefit is then lost.
polyethylene, vent edge curl and premature wear.
Maintenance Instructions :
polypropylene Helpful hints for proper appli- Periodically inspect product application to
Painted metal, Solvent wipe or
painted plastics, degrease wash , rinse cation : maintain product effectiveness.
painted wood, and let dry. Rough or smooth, porous surfaces : Keep free of dirt and other residue that
gel-coated fiber- Prime coat with a 3M primer is recommended might impair functionality.
glass, for proper adhesion. General Purpose, Conformable treads should
epoxy floors Painted surfaces : be decked-brushed regularly.
Porous concrete Degrease wash, rinse 3M Safety-Walk materials can be applied on Fine and Medium Resilient should be
and let dry most painted surfaces which are in good mopped or deck-brushed regularly.
Painted concrete Degrease wash, rinse condition and will adhere as well as the base Use appropriate degreaser/cleaner as a gen-
and let dry
paint. Painted surfaces must be thoroughly eral maintenance cleaner to keep material
Vinyl tile, Strip off floor finish,
dry before the application. and surrounding surfaces free of soil and
marble, wash , rinse and let
terrazzo dry Treated and untreated wood : grease.
ceramic Wood surfaces must be sealed or painted Removal and replacement:
Quarry tile Degrease wash, rinse before application of 3M Safety-Walk materi- To remove and replace worn or torn mate-
and let dry als. rial:
Immersed surfaces : 1. Start by pulling up old material. Use of a
3M Safety-Walk materials are not recom- heat gun and a scraper will assist in this
Application Instructions : mended for continuous immersion in water or
Tools needed: rubber hand roller or rubber process.
for areas with constant moisture seepage. 2. After total removal of old mate-
mallet. Grouted floors :
1. Individual pieces should be spaced a rials, use a degreaser or solvent
Do not bridge over joins, grouting, cracks or based cleaner to remove adhesive
minimum of 12 mm apart and a maximum breaks in all surfaces. Cut into smaller pieces.
of 50 mm apart. residues before proceeding with
Kitchen and greasy floors : re-application of 3M Safety-
2. Round the corners of any pieces cut from Application of 3M Safety-Walk materials is
rolls. Walk materials.
not recommended for quarry tile in commer-
3. Peel protective liner back about 50 mm cial kitchens. (because quarry tiles are often
from one end and position piece on sur- impregnated with grease)
Wet areas :