Sie sind auf Seite 1von 31

Q452 L3 Service Manual

1:Technical Specifications

Particular Remarks
Key Matrix For Flashing NA
Chipset MT6737
Android Version Android M
Frequency Quad Core, 1.1GHz LTE CAT4
Network Mode 850MHz/900MHz/1800MHz/1900MHz
3G Band B1,B8,B5
4G Band B3,B7,B8
ROM 16G
RAM 2G
Internal SD Card memory 10.8G
Expandable Memory 64G
Factory mode code Press Vol-/ power key at the same time
Good Earpiece volume 32Ω± 15%
Good Loudspeaker volume 8Ω± 5%
Good MIC volume 2.2kΩ± 5%
Good Vibrator volume 30Ω± 5%

2:CAUTIONS
I. Flashing & Servicing must be undertaken by qualified personnel only.
II. Ensure all work is carried out at an anti-static workstation and that an anti-static wrist strap is worn.
III. Use only approved Tools & components as specified in the parts list.
IV. Ensure all components, modules, screws, and insulators are correctly re-fitted after servicing and
alignment
V. Ensure all cables and wires are repositioned correctly if Handset disassembled
VI. Electrostatic discharge can easily damage the sensitive components of electronic products. Therefore,
Service Centre must Adhere the precautions which mentioned above.
3. L3 Service Manual

Main camera Receiver USB P-Sensor


connector Connector Connector ( U1703)
(J1501) (SC4/SC5) (J1804)

XTAL
BT/WIFI/GPS/ (Y801)
FM
( U1300)

RF IC
Flash
(U800)
(U401)

()

RF 2G PA
(U1200)

Backlight driver Power IC CPU 3/4G PA


(U1401) (U601) (U400) ()
Earphone TP
Front Camera
Connector connector
connector
(J1601) (J1402)
(J1500)
WIFI/BT/GPS
4G NET ANT
ANT (E1300/E1301)
(E1101/E1102
)
Flashlight Switch
driver charge IC
(U1502) (U1802)

Flashlight
SIM
(D1502)
connector
(J1800)
SIM
Side KEY connector
connector (J1801)
(J703) G-Sensor
(U1700)

Audio PA LCD
Battery T-Flash
(U1600) Connector
connector connector
(J800)
(J1802) (J1803)

1. Unable to load Software:

Solution:
 First check the computer can recognize the device or not, if not, Re-load it.

 Then check the USB port to master control circuit is normal or not.:format the flash and upgrade again if fail in
the Proceed of downloading.

 Use a fresh data cable


 Check the I/O connector soldering quality, if not , Re-sold it or change it.

 Check the CPU work normally or not. Re-Solder the CPU or change it

USB
Connector

CPU

Flash
2. No power on

Solution:
 Flash the handset with latest SW

 Check the battery have capacity or not ,if not ,Change it

 Charging with transferred to 4.0 V dc power supply to the mainboard on battery Re-soldering ,check

The mainboard work current, the normal starting current will be from 100 ma jump to light screen
 Enter boot LOGO 400 ma to completely started around 500 ma, if the current not right then check

Whether has short circuit or open circuit phenomenon or not.


 Check the Power IC work normally or not ,Re-Solder it or change it

The output voltage normally or not


 Check the 26M crystal work normally or not ,Re-Solder it or change it

 Check the CPU work normally or not, Re-Solder CPU or change it

CPU

26M
crystal

Power
IC
3. Not charging:

Solution:
 Flash the handset with latest SW

 Plug in the charger to check whether the machine has a charging icon, if don’t have, then check the

5V power pin of USB port connect the mainboard or not


 Check the voltage of battery when charging If it reaches 4.2V, has shown in front of the

Transmission, now maybe is the battery bad so that no charging.


 Check the I/O connector work well or not ,if not , Re-Solder or change it

 Check the charging switch work well or not ,if not , Re-Solder or change it

 Check the Power IC work normally or not, Re-Solder CPU or change it

 Check the CPU work normally or not. Re-Solder the CPU or change it
I/O Switch
connector Charging IC
switch IC

Power IC
4. LCD / Display problem:

Solution:
 Flash the handset with latest SW

 Check the connect ribbon cable saddle normally or not , Re-assembly LCD.

 Check the LCD connector work normally or not, Re-Solder LCD connector or change it

 Check the CPU work normally or not, Re-Solder CPU or change it

.
LCD
CPU connector
5. Touch panel is not working

 Flash the handset with latest SW

 Check the connect ribbon cable saddle normally or not , Re-assembly TP.

 Check the TP connector work normally or not, Re-Solder TP connector or change it

 Check the CPU work normally or not, Re-Solder CPU or change it

TP
CPU
connector
6. LCD backlight not on or dark

Solution:
 Flash the handset with latest SW

 Check the connect ribbon cable saddle normally or not , Re-assembly LCD.

 Check the LCD connector work normally or not, Re-Solder LCD connector or change it

 Check the Backlight IC work normally or not, Re-Solder Backlight IC or change it

 Check the CPU work normally or not, Re-Solder CPU or change it

Backlight CPU
LCD
IC
Connector
7. SIM not detecting:

Solution:
 Flash the handset with latest SW
 Check if the SIM card is obviously damaged, if yes, Replace the SIM card socket

 Check if the ground impedance of each pin of the SIM card socket(except the ground pin)is low(lower than grade ),if
yes, Replace the resistor of the corresponding pin;

 Check if the series resistors on each network of the SIM card have pseudo soldering ,if yes, Carry out repair soldering
of the series resistors on each signal line;

 Check the Power IC normally or not, then Re-Solder Power IC or change it.

 Check the CPU normally or not, then Re-Solder CPU or change it.

CPU Power IC SIM


.
Connector
8. SD card not detecting:

Solution:
 Flash the handset with latest SW

 Check if the TF card is obviously damaged, if yes, Re-Solder TF connector or change it

 Check if the ground impedance of each pin of the TF card socket(except the ground pin)is low(lower than grade ),if
yes, Replace the resistor of the corresponding pin;

 Check if the series resistors on each network of the TF card have pseudo soldering ,if yes, Carry out repair soldering
of the series resistors on each signal line;

 Check the Power IC normally or not, then Re-Solder Power IC or change it.

 Check the CPU normally or not, then Re-Solder CPU or change it.

CPU Power IC TF
connector
9. Front camera is not working:

Solution:
 Flash the handset with latest SW

 Check if the Camera is obviously damaged, if yes, Replace the Camera ;

 Check if the ground impedance of each pin of the Camera connector (except the ground pin)is low(lower than
grade ),if yes, Replace the resistor of the corresponding pin;

 Check if the series resistors on each network of the Camera connector have pseudo soldering ,if yes, Carry out repair
soldering of the series resistors on each signal line;

 Check the PMU normally or not ,then Re-solder PMU or charge it.

 Check the CPU normally or not, then Re-Solder CPU or change it.

Camera
CPU
connector

PMU
10. Rear camera is not working:

Solution:
 Flash the handset with latest SW

 Check if the Camera is obviously damaged, if yes, Replace the Camera ;

 Check if the ground impedance of each pin of the Camera connector (except the ground pin)is low(lower than
grade ),if yes, Replace the resistor of the corresponding pin;

 Check if the series resistors on each network of the Camera connector have pseudo soldering ,if yes, Carry out repair
soldering of the series resistors on each signal line;

 Check the PMU normally or not, then Re-Solder PMU or charge it.

 Check the CPU normally or not, then Re-Solder CPU or change it.
Camera
connector

CPU

PMU
11. MIC no sound:

Solution:
 Flash the handset with latest SW

 Check the MIC bad or not. then Re-Solder MIC or change it

 Check the connection of main board and vice board normally or not.

 Check Earphone connector also , If Earphone connector got shorted : MIC & Receiver will not work

 Check the MIC work normally or not , Re-Solder the MIC or change it.

 Check the LCD FPC Assembly Quality , if not ,Re-Assembly it or change it.

 Check the FPC connector soldering Quality , if not ,Re-sold it or change it.

 Check the power IC work normally or not. Re-Solder the power IC or change it

 Check the CPU work normally or not. Re-Solder the CPU or change it

LCD/MIC FPC
CPU Power IC
Connector

MIC FPC
MIC
connector
12. Receiver not working:

Solution:
 Flash the handset with latest SW
 Check the receiver bad or not, then change it.

 Check the receiver circuit normally or not.


 Check Earphone connector also , If Earphone connector got shorted : MIC & Receiver will not work

 Check the Power IC work normally or not. Re-Solder the Power IC or change it

 Check the CPU normally or not, then Re-Solder CPU or change it.

Receiver
Slot

CPU

Power IC

13. Speaker not working:

Solution:
 Flash the handset with latest SW
 Check the Speaker bad or not, else change it.

 Check Earphone connector also , If Earphone connector got shorted : MIC & Receiver will not work

 Check the SPK FPC soldering quality , if not ,Re-sold it or change it.

 Check the Main FPC Assembly Quality , if not ,Re-Assembly it or change it.

 Check the FPC connector soldering Quality ,if not ,Re-sold it or change it.

 Check the Power IC work normally or not. Re-Solder the Power IC or change it

 Check the CPU work normally or not. Re-Solder the CPU or change it
LCD/SPK FPC
CPU Power IC Connector

SPK Slot FPC connector


14. Earphone not working:

Solution
 Flash the handset with latest SW
 Check the earphone normally or not, then change it;

 Check the earphone connector normally or not. then Re-Solder earphone connector or change it

 Check the Power IC normally or not, then Re-Solder Power IC or change it.

 Check the CPU normally or not, then Re-Solder CPU or change it.

Earphone
. Earphone
CPU Connector

Power IC
15. G SENSOR not working:

Solution:
 Flash the handset with latest SW

 Check the g-sensor work normally or not, Re-solder or change it

 Check the CPU work normally or not, Re-Solder CPU or change it

CPU G-Sensor
16. FM not working:

Solution:
 Flash the handset with latest SW
 Check the earphone normally or not, then change it;

 Check the first pin of earphone, well connect with earphone line or not. then Re-Solder earphone connector or
change it

 Check the Power IC normally or not, then Re-Solder Power IC or change it.

 Check the CPU normally or not, then Re-Solder CPU or change it.

Earphone
Earphone
CPU Connector

Power IC
17. WI-FI is not working properly:

Solution:

 Check WIFI 11 to 30 S if these are working fine。

 Flash the handset with latest SW

 Check the WIFI antenna normally or not, then Re-Solder or change it.

 Check the WIFI chip work normally or not, then Re-Solder CPU or change it.

 Check the CPU normally or not, then Re-Solder CPU or change it.

WiFi&BT&GPS&FM WiFi&BT
CPU
4 in 1 IC ANT
18. BT is not working fine:

Solution:
 Check BT 11 to 30 S if these are working fine。

 Flash the handset with latest SW

 Check the BT antenna normally or not, then Re-Solder or change it.

 Check the BT chip work normally or not, then Re-Solder CPU or change it

 Check the CPU normally or not, then Re-Solder CPU or change it.

WiFi&BT&GPS&FM WiFi&BT
CPU
4 in 1 IC ANT
19. Keys are not working:

Solution:
 Flash the handset with latest SW

 Check if the keys FPC normally or not, Re-Solder Side key or change it

 Check the circuit from keys to CPU normally or not ,then Re-Solder CPU or change it

Side key
CPU
Slot
20. Reset is not working: N/A

21. Vibrator is not working:

Solution:
 Flash the handset with latest SW

 Check if the vibrator is failure then Re-Solder Vibrator or change it

 Check the Main FPC Assembly Quality ,if not ,Re-Assembly it or change it.

 Check the FPC connector soldering Quality ,if not ,Re-sold it or change it.

 Check the power IC work normally or not. Re-Solder the power IC or charge it.

 Check the CPU work normally or not. Re-Solder the CPU or change it

CPU Power IC
LCD/Vibrator
FPC connector

Vibrator Vibrator FPC


slot
22. Proximity sensor is not working
Solution:

 Flash the handset with latest SW

 Check the Proximity sensor normally or not ,Re-Solder Proximity sensor or change it.

 Check the Power IC work normally or not, Re-Solder Power IC or change it

 Check the CPU work normally or not, Re-Solder CPU or change it

CPU Proximity
sensor

Power IC
23.GPS cannot locate and open:
Solution:

 Check BT 11 to 30 S if these are working fine。

 Flash the handset with latest SW


 Check the GPS antenna normally or not, then Re-Solder or change it.

 Check the WIFI&BT&GPS&FM IC normally or not, then Re-Solder CPU or change it.

 Check the CPU normally or not, then Re-Solder CPU or change it.

WiFi&BT&GPS&FM WiFi&BT
CPU
4 in 1 IC ANT
24. Network issue:
Solution:
 Flash the handset with latest SW

 Check the RF Antenna Slot soldering quality, if not, Re-sold it or change it.

 Check the RF coaxial line normally or not. Re- Assembly it or change it.

 Check the RF connector normally or not. Re-sold it or change it

 Strongly solder 26M Crystal or change it

 Check the RF PA normally or not, then Re-Solder RF PA or change it.

 Check the RF IC normally or not, then Re-Solder RF IC or change it.

 Check the CPU work normally or not. Re-Solder the CPU or change it

26M RF antenna
Connector

CPU RF IC RF RF ANT
PA(2G) connector
Thanks

Das könnte Ihnen auch gefallen