Sie sind auf Seite 1von 43

Instrument Panel Page 1 of 43

Audi > A8/A8L > 2004-2008


Body Interior
70 - Removal and Installation

Instrument Panel

Left Trim Molding

Right Trim Molding with Switch Strip

Instrument Panel Vent

Instrument Cluster Trim

Front Information Display Control Head Trim

Trim over Glove Compartment

Right and Left Defroster Outlets

Sunlight Photo Sensor with Cover

Center Defroster Outlet

Indirect Ventilation Trim

Left Instrument Panel Cover

Right Instrument Panel Cover

Instrument Panel

Left Trim Molding

x-ebahn:///C:/Program%20Files/eBahn/data/AUDI-D-D3-BD02.ebn/AUDI/D/D3/Repair%... 2/17/2014
Instrument Panel Page 2 of 43

Removing

Carefully disengage decorative panel - 1 - from instrument panel using trim removal
wedge 3409 - arrows - .

Installing

Installation is reverse of removal.

Right Trim Molding with Switch Strip

Removing

Open coin tray.

Slide coin tray panel toward the left out of catch - arrow - and remove.

x-ebahn:///C:/Program%20Files/eBahn/data/AUDI-D-D3-BD02.ebn/AUDI/D/D3/Repair%... 2/17/2014
Instrument Panel Page 3 of 43

Open glove compartment.

Carefully disengage decorative panel with switch strip - 1 - - starting above the glove
compartment - from instrument panel using trim removal wedge 3409 .

Pull off decorative panel with switch strip in - direction of arrow - .

Note:

Be especially careful when releasing clip on the drivers side end of decorative panel.

Disconnect electrical connector.

Installing

Installation is reverse of removal, noting the following:

When inserting decorative panel - 1 - with switch strip, make sure that both catches in
panel center are inserted between instrument panel and screen housing - arrows - .

Instrument Panel Vent

x-ebahn:///C:/Program%20Files/eBahn/data/AUDI-D-D3-BD02.ebn/AUDI/D/D3/Repair%... 2/17/2014
Instrument Panel Page 4 of 43

Removing

Turn knurled wheel - 3 - or air outlet vent completely upward.

Insert one watchmakers screwdriver each - 1 - into air vent retaining clamps above the
lower ventilation fin - 2 - .

Pull air vent alternating on left and right side out of the installation opening,
watchmakers screwdrivers must remain inserted while doing this.

Note:

Pull air vent out of installation opening using Hook 3438 if necessary.

Disconnect electrical harness connector at air vent.

Installing

Installation is reverse of removal.

Instrument Cluster Trim

x-ebahn:///C:/Program%20Files/eBahn/data/AUDI-D-D3-BD02.ebn/AUDI/D/D3/Repair%... 2/17/2014
Instrument Panel Page 5 of 43

Removing

Position the steering wheel so that it is as far rearward and down as possible, using the
full adjustment range of the steering column adjuster.

Switch off ignition and remove ignition key.

Carefully disengage decorative panel - 1 - from instrument panel using trim removal
wedge 3409 - arrows - .

Open coin tray.

Slide coin tray panel toward the left out of catch - arrow - and remove.

x-ebahn:///C:/Program%20Files/eBahn/data/AUDI-D-D3-BD02.ebn/AUDI/D/D3/Repair%... 2/17/2014
Instrument Panel Page 6 of 43

Open glove compartment.

Carefully disengage decorative panel - 1 - with switch strip - starting above the glove
compartment - from instrument panel using trim removal wedge 3409 .

Pull off decorative panel with switch strip in - direction of arrow - .

Note:

Be especially careful when releasing clip on the drivers side end of decorative panel.

Disconnect electrical connector.

Turn knurled wheel - 3 - for left air vent next to instrument cluster completely upward.

Insert one watchmakers screwdriver each - 1 - into air vent retaining clamps above the
lower ventilation fin - 2 - .

Pull air vent alternating on left and right side out of the installation opening,
watchmakers screwdrivers must remain inserted while doing this.

Note:

Pull air vent out of installation opening using Hook 3438 if necessary.

x-ebahn:///C:/Program%20Files/eBahn/data/AUDI-D-D3-BD02.ebn/AUDI/D/D3/Repair%... 2/17/2014
Instrument Panel Page 7 of 43

Disconnect electrical harness connector at air vent.

Repeat the procedure on the right air outlet near the instrument cluster.

Remove bolts - arrows - .

Note:

Secure a cloth with adhesive tape to protect the steering column trim and the steering
column lever.

Pull the instrument panel cover away from the instrument cluster slightly.

Disconnect the electrical connectors on the instrument cluster cover.

Engage the turn signal switch in the bottom switch position.

Activate the one-touch wiping and hold the instrument panel cover in this wiper switch
position.

Installing

Installation is reverse of removal.

Tightening torque:

Instrument cluster/instrument cluster cover to instrument panel: 3 Nm

Front Information Display Control Head Trim

x-ebahn:///C:/Program%20Files/eBahn/data/AUDI-D-D3-BD02.ebn/AUDI/D/D3/Repair%... 2/17/2014
Instrument Panel Page 8 of 43

Removing

Turn knurled wheel - 3 - for left air vent above glove compartment completely upward.

Insert one watchmakers screwdriver each - 1 - into air vent retaining clamps above the
lower ventilation fin - 2 - .

Pull air vent alternating on left and right side out of the installation opening,
watchmakers screwdrivers must remain inserted while doing this.

Note:

Pull air vent out of installation opening using Hook 3438 if necessary.

Disconnect electrical harness connector at air vent.

Repeat the procedure on the right air outlet near the instrument cluster.

Pry off panel at left and right on lower edge using trim removal wedge 3409 - arrow 1 - .

Pull out panel from tabs of display unit downward - arrow 2 - .

Installing

x-ebahn:///C:/Program%20Files/eBahn/data/AUDI-D-D3-BD02.ebn/AUDI/D/D3/Repair%... 2/17/2014
Instrument Panel Page 9 of 43

Installation is reverse of removal.

Trim over Glove Compartment

Removing

Switch off ignition and remove ignition key.

Turn knurled wheel - 3 - for left air vent above glove compartment completely upward.

Insert one watchmakers screwdriver each - 1 - into air vent retaining clamps above the
lower ventilation fin - 2 - .

Pull air vent alternating on left and right side out of the installation opening,
watchmakers screwdrivers must remain inserted while doing this.

Note:

Pull air vent out of installation opening using Hook 3438 if necessary.

Disconnect electrical harness connector at air vent.

Repeat procedure at right air vent, above glove compartment.

x-ebahn:///C:/Program%20Files/eBahn/data/AUDI-D-D3-BD02.ebn/AUDI/D/D3/Repair%... 2/17/2014
Instrument Panel Page 10 of 43

Open coin tray.

Slide coin tray panel toward the left out of catch - arrow - and remove.

Open glove compartment.

Carefully disengage decorative panel - 1 - with switch strip - starting above the glove
compartment - from instrument panel using trim removal wedge 3409 .

Pull off decorative panel with switch strip in - direction of arrow - .

Note:

Be especially careful when releasing clip on the drivers side end of decorative panel.

Disconnect electrical connector.

Remove the coin tray.

x-ebahn:///C:/Program%20Files/eBahn/data/AUDI-D-D3-BD02.ebn/AUDI/D/D3/Repair%... 2/17/2014
Instrument Panel Page 11 of 43

Remove bolts - arrows - .

Remove panel - 1 - above glove compartment.

Installing

Installation is reverse of removal, noting the following:

When inserting decorative panel - 1 - with switch strip, make sure that both catches in
panel center are inserted between instrument panel and screen housing - arrows - .

Tightening torque:

Panel above glove compartment to instrument panel: 2.5 Nm

Right and Left Defroster Outlets

x-ebahn:///C:/Program%20Files/eBahn/data/AUDI-D-D3-BD02.ebn/AUDI/D/D3/Repair%... 2/17/2014
Instrument Panel Page 12 of 43

Removing

Carefully pull off defroster vent - 1 - in - direction of arrow - using hook for front end
3370 .

Installing

Engage hooks - 1 - of defroster vent in instrument panel cutout.

Then engage defroster vent - 3 - in instrument panel with retaining spring - 2 - .

Sunlight Photo Sensor with Cover

x-ebahn:///C:/Program%20Files/eBahn/data/AUDI-D-D3-BD02.ebn/AUDI/D/D3/Repair%... 2/17/2014
Instrument Panel Page 13 of 43

Removing

Unclip cover cap - 1 - using a feeler gauge 0.35 mm - 2 - out of center defroster vent -
arrow - .

Pry out Sunlight Photo Sensor G107 - item 3 - and disconnect harness connector.

Installing

Installation is reverse of removal.

Center Defroster Outlet

Removing

Unclip cover cap - 1 - using a feeler gauge 0.35 mm - 2 - out of center defroster vent -
arrow - .

Pry out Sunlight Photo Sensor G107 - item 3 - and disconnect harness connector.

x-ebahn:///C:/Program%20Files/eBahn/data/AUDI-D-D3-BD02.ebn/AUDI/D/D3/Repair%... 2/17/2014
Instrument Panel Page 14 of 43

Remove bolt - 1 - .

As depicted in the illustration, pry center defroster vent - 2 - out of instrument panel
using trim removal wedge 3409 .

Installing

Installation is reverse of removal.

Tightening torque:

Center defroster vent to instrument panel: 2 Nm

Indirect Ventilation Trim

Removing

Unclip cover cap - 1 - using a feeler gauge 0.35 mm - 2 - out of center defroster vent -
arrow - .

x-ebahn:///C:/Program%20Files/eBahn/data/AUDI-D-D3-BD02.ebn/AUDI/D/D3/Repair%... 2/17/2014
Instrument Panel Page 15 of 43

Pry out Sunlight Photo Sensor G107 - item 3 - and disconnect harness connector.

Remove bolt - 1 - .

As depicted in the illustration, pry center defroster vent - 2 - out of instrument panel
using trim removal wedge 3409 .

Remove the bolts - 2 - .

Remove panel for indirect ventilation - 1 - .

x-ebahn:///C:/Program%20Files/eBahn/data/AUDI-D-D3-BD02.ebn/AUDI/D/D3/Repair%... 2/17/2014
Instrument Panel Page 16 of 43

Installing

Installation is reverse of removal, noting the following:

Make sure that clips - 3 - engage into instrument panel mounts.

Tightening torque:

Panel for indirect ventilation to instrument panel: 2 Nm

Left Instrument Panel Cover

Removing

Pry the left instrument panel cover off using a screwdriver - arrow - .

Installing

Installation is reverse of removal.

Right Instrument Panel Cover

x-ebahn:///C:/Program%20Files/eBahn/data/AUDI-D-D3-BD02.ebn/AUDI/D/D3/Repair%... 2/17/2014
Instrument Panel Page 17 of 43

Removing

Pry the right instrument panel cover off using a screwdriver - arrow - .

Installing

Installation is reverse of removal.

Instrument Panel

CAUTION!

On vehicles equipped with Audi Telematics by OnStar, switch-off


emergency (back-up) battery for Telematic/Telephone Control
Module prior to disconnecting vehicle battery. Switch-on
emergency (back-up) battery after reconnecting vehicle battery
Communication - Repair Group 91

Removing

Front Information Display Control Head J685 (MMI screen) must be closed.

Note:

Install all cable ties that were loosened or cut off during removal in the same
positions.

Position the steering wheel so that it is as far rearward and down as possible, using the
full adjustment range of the steering column adjuster.

Set front seats to rearmost position and fold backrests to 45 degree position.

x-ebahn:///C:/Program%20Files/eBahn/data/AUDI-D-D3-BD02.ebn/AUDI/D/D3/Repair%... 2/17/2014
Instrument Panel Page 18 of 43

Switch off ignition and remove ignition key.

With ignition switched off, disconnect battery Ground (GND) cable Electrical
Equipment - Repair Group 27 .

Remove airbag unit and steering wheel Driver Airbag .

Pry the left instrument panel cover off using a screwdriver - arrow - .

Carefully disengage decorative panel - 1 - from instrument panel using trim removal
wedge 3409 - arrows - .

x-ebahn:///C:/Program%20Files/eBahn/data/AUDI-D-D3-BD02.ebn/AUDI/D/D3/Repair%... 2/17/2014
Instrument Panel Page 19 of 43

Open coin tray.

Slide coin tray panel toward the left out of catch - arrow - and remove.

Open glove compartment.

Carefully disengage decorative panel - 1 - with switch strip - starting above the glove
compartment - from instrument panel using trim removal wedge 3409 .

Note:

Be especially careful when releasing clip on the drivers side end of decorative panel.

Disconnect electrical connector.

x-ebahn:///C:/Program%20Files/eBahn/data/AUDI-D-D3-BD02.ebn/AUDI/D/D3/Repair%... 2/17/2014
Instrument Panel Page 20 of 43

Unbolt drivers side storage compartment - arrows - .

Disconnect electrical connectors.

Vehicles with knee airbag: Pull locking mechanism - 2 - in direction of arrow and
disconnect electrical harness connectors - 1 - and - 3 - .

Pry the right instrument panel cover off using a screwdriver - arrow - .

x-ebahn:///C:/Program%20Files/eBahn/data/AUDI-D-D3-BD02.ebn/AUDI/D/D3/Repair%... 2/17/2014
Instrument Panel Page 21 of 43

If present, remove CD changer as follows:

Insert two hooks of radio removal tool T10057 into the front of the CD-changer.

Top L - upper left

Top R - upper right

Remove the CD changer from the mounting frame.

Disconnect electrical connector.

Disconnect harness connector for fiber-optic cable.

Seal the open wiring set connector - 2 - for fiber-optic cable using Protective Cap For
Cable Connector VAS 6223/9 - item 1 - .

Note:

The protective cap prevents soiling and damage to fiber optic face, which would
impair light transfer.

Remove the release tool from the CD changer by pressign the locking tabs on the
changer.

x-ebahn:///C:/Program%20Files/eBahn/data/AUDI-D-D3-BD02.ebn/AUDI/D/D3/Repair%... 2/17/2014
Instrument Panel Page 22 of 43

If present, remove storage compartment in glove compartment, to do so disengage


retaining straps - 1 - and - 2 - in - direction of arrow - using a small screwdriver.

Pull storage compartment out of glove compartment.

Remove bolts - arrows - .

Remove bolts - 1 - and - 2 - .

Disconnect electrical harness connector - 1 - for glove compartment wiring harness - 2 -

x-ebahn:///C:/Program%20Files/eBahn/data/AUDI-D-D3-BD02.ebn/AUDI/D/D3/Repair%... 2/17/2014
Instrument Panel Page 23 of 43

from lead wire - 3 - .

Vehicles with knee airbag: Pull locking mechanism - 2 - in direction of arrow and
disconnect electrical harness connectors - 1 - and - 3 - .

Remove glove compartment.

Vehicles without rear A/C Control Head (Climatronic)

Open rear ashtray - 2 - .

Remove trim - 1 - from mounting frame - arrow - .

Close the ashtray.

x-ebahn:///C:/Program%20Files/eBahn/data/AUDI-D-D3-BD02.ebn/AUDI/D/D3/Repair%... 2/17/2014
Instrument Panel Page 24 of 43

Remove ashtray from mounting frame - in direction of arrow - .

Vehicles with rear A/C Control Head (Climatronic)

Pry panel - 1 - out of mounting frame - arrow - using trim removal wedge 3409 .

Procedure for all vehicles

Remove bolts - arrows - .

Remove mounting frame - 1 - with air vents and rear ashtray or Rear A/C Control Head

x-ebahn:///C:/Program%20Files/eBahn/data/AUDI-D-D3-BD02.ebn/AUDI/D/D3/Repair%... 2/17/2014
Instrument Panel Page 25 of 43

(Climatronic).

Note:

To disconnect the electrical harness connector on rear A/C control head (Climatronic),
press locking button - 1 - , rotate retaining bracket in direction of arrow and disconnect
connector.

Disconnect electrical harness connectors - 1 to 4 - .

x-ebahn:///C:/Program%20Files/eBahn/data/AUDI-D-D3-BD02.ebn/AUDI/D/D3/Repair%... 2/17/2014
Instrument Panel Page 26 of 43

Remove nuts - arrows - for rear center console.

Vehicles with split center armrest

Fold center armrests upward.

Pull off backrest hinge cover upward - arrow - .

Remove bolts - arrows - .

Disconnect electrical harness connectors for storage compartment light in center


armrest.

Pull center armrests upward and remove.

Vehicles with one-piece center armrest

Fold center armrest upward.

x-ebahn:///C:/Program%20Files/eBahn/data/AUDI-D-D3-BD02.ebn/AUDI/D/D3/Repair%... 2/17/2014
Instrument Panel Page 27 of 43

Procedure for all vehicles

Pry storage compartment at forward corners out of center console - arrow 1 - using
Trim Removal Wedge 3409 and pull storage compartment forward - arrow 2 - .

Disconnect electrical harness connectors - 1 - and - 2 - and remove storage


compartment.

Disconnect electrical harness connectors - 1 - .

Unscrew bolts - arrows - on both sides of center console.

x-ebahn:///C:/Program%20Files/eBahn/data/AUDI-D-D3-BD02.ebn/AUDI/D/D3/Repair%... 2/17/2014
Instrument Panel Page 28 of 43

Remove the front ashtray insert - 1 - by pressing the knob - arrow - .

Unscrew bolt - arrow - and remove front ashtray housing.

Disconnect electrical connector.

Remove the center console selector trim upward - arrows - .

Disconnect electrical connectors.

x-ebahn:///C:/Program%20Files/eBahn/data/AUDI-D-D3-BD02.ebn/AUDI/D/D3/Repair%... 2/17/2014
Instrument Panel Page 29 of 43

Remove the bolts - 2 - .

Release retaining springs - 1 - using a small screwdriver - arrow - .

Swivel Climatronic Control Module J255 at top edge toward rear.

Remove Climatronic Control Module from mount.

Disconnect the electrical connectors - A through E - by releasing the catches - G - .

Disconnect electrical harness connector - F - .

x-ebahn:///C:/Program%20Files/eBahn/data/AUDI-D-D3-BD02.ebn/AUDI/D/D3/Repair%... 2/17/2014
Instrument Panel Page 30 of 43

Remove bolts - arrows - .

Press on the rocker - A - of selector lever emergency release using e.g. a screwdriver.

At the same time, shift selector lever out of position "P" into position "D" .

x-ebahn:///C:/Program%20Files/eBahn/data/AUDI-D-D3-BD02.ebn/AUDI/D/D3/Repair%... 2/17/2014
Instrument Panel Page 31 of 43

Turn the sleeve - 1 - to the left and slide it down as far as the stop.

Remove selector lever knob - 2 - upward.

Release retaining hooks - 1 - on both sides of selector mechanism - arrow - and raise
cover - 3 - upward.

Disconnect electrical harness connector - 2 - and remove cover.

Lift rear center console and disconnect electrical harness connectors on underside of
center console.

Remove center console toward rear.

Remove screws - 3 - and - 5 - with Special Screwdriver T8 T40056 A .

x-ebahn:///C:/Program%20Files/eBahn/data/AUDI-D-D3-BD02.ebn/AUDI/D/D3/Repair%... 2/17/2014
Instrument Panel Page 32 of 43

Remove TORX bolts - 6 - and hex socket bolt - 4 - .

Disconnect upper steering column switch trim - 2 - from lower trim - 1 - and remove both
parts.

Remove bolt - 2 - .

Disconnect electrical connectors - 1 - , - 3 - and - 4 - .

Carefully remove the steering column switch together with the steering column
electronic systems control module.

Turn knurled wheel - 3 - for left air vent next to instrument cluster completely upward.

Insert one watchmakers screwdriver each - 1 - into air vent retaining clamps above the
lower ventilation fin - 2 - .

Pull air vent alternating on left and right side out of the installation opening,
watchmakers screwdrivers must remain inserted while doing this.

Note:

Pull air vent out of installation opening using Hook 3438 if necessary.

x-ebahn:///C:/Program%20Files/eBahn/data/AUDI-D-D3-BD02.ebn/AUDI/D/D3/Repair%... 2/17/2014
Instrument Panel Page 33 of 43

Disconnect electrical harness connector at air vent.

Repeat the procedure on the right air outlet near the instrument cluster.

Remove bolts - arrows - .

Pull the instrument panel cover away from the instrument cluster slightly.

Disconnect the electrical connectors on the instrument cluster cover.

Release left and right retaining clamps - arrows - and pull out instrument cluster slightly
from instrument panel.

x-ebahn:///C:/Program%20Files/eBahn/data/AUDI-D-D3-BD02.ebn/AUDI/D/D3/Repair%... 2/17/2014
Instrument Panel Page 34 of 43

Press catch - 1 - , rotate retaining bracket in - direction of arrow - and remove


connector to do so.

Remove instrument cluster.

Turn knurled wheel - 3 - for left air vent above glove compartment completely upward.

Insert one watchmakers screwdriver each - 1 - into air vent retaining clamps above the
lower ventilation fin - 2 - .

Pull air vent alternating on left and right side out of the installation opening,
watchmakers screwdrivers must remain inserted while doing this.

Note:

Pull air vent out of installation opening using Hook 3438 if necessary.

Disconnect electrical harness connector at air vent.

Repeat procedure at right air vent, above glove compartment.

x-ebahn:///C:/Program%20Files/eBahn/data/AUDI-D-D3-BD02.ebn/AUDI/D/D3/Repair%... 2/17/2014
Instrument Panel Page 35 of 43

Release retaining tabs - 1 - of coin tray.

Pull coin tray out of instrument panel - arrow - .

Disconnect the rear electrical harness connector on coin tray.

Remove heating channel in drivers side footwell.

Disconnect electrical harness connectors - 1 - .

Unclip harness connector - 5 - at relay and fuse carrier.

Remove the bolts - 3 - .

Disengage retaining pin - 4 - of relay and fuse carrier at the side guide - arrow - .

Remove relay and fuse carrier - 2 - and set it down with electrical wires connected in the

x-ebahn:///C:/Program%20Files/eBahn/data/AUDI-D-D3-BD02.ebn/AUDI/D/D3/Repair%... 2/17/2014
Instrument Panel Page 36 of 43

footwell.

Remove bolts - 1 - of left fuse holder - 2 - .

Release retaining tabs - arrows - and remove fuse holder from instrument panel central
tube, electrical wires remain connected.

Release securing clip - arrow 1 - on left CAN-connector.

Push retaining tab - arrow 2 - and disconnect 46-Pin CAN Connector T46a inward,
electrical wires remain connected.

x-ebahn:///C:/Program%20Files/eBahn/data/AUDI-D-D3-BD02.ebn/AUDI/D/D3/Repair%... 2/17/2014
Instrument Panel Page 37 of 43

Secure steering column - 1 - with a cable tie - 2 - to prevent the upper and lower parts of
steering column from separating inadvertently during removal.

Note:

If splines are no longer found in their original installation position, this may cause
flapping noises while driving.

Remove bolts - arrows - and set down steering column in footwell.

Note:

To disconnect electrical harness connector on headlamp range control module, press


catch - 1 - , rotate retaining clip in - direction of arrow - and disconnect connector.

x-ebahn:///C:/Program%20Files/eBahn/data/AUDI-D-D3-BD02.ebn/AUDI/D/D3/Repair%... 2/17/2014
Instrument Panel Page 38 of 43

Disconnect electrical harness connectors on headlamp range control module - 2 - and


on warning buzzer for front parking aid system - 1 - .

Remove bolts - arrows - .

Remove Front Information Display Control Head Control Module J523 .

Disconnect electrical connector - 1 - .

Note:

The connectors - item 2 - and - 3 - remain connected.

Set down Front Information Display Control Head Control Module in footwell.

x-ebahn:///C:/Program%20Files/eBahn/data/AUDI-D-D3-BD02.ebn/AUDI/D/D3/Repair%... 2/17/2014
Instrument Panel Page 39 of 43

Remove bolts - arrows - .

Remove Data Bus On Board Diagnostic Interface J533 .

Note:

The connectors - item 1 - and - 2 - remain connected.

Set down Data Bus On Board Diagnostic Interface in footwell.

Remove bolts - 1 - of right fuse holder - 2 - .

Release retaining tabs - arrows - and remove fuse holder from instrument panel central
tube, electrical wires remain connected.

x-ebahn:///C:/Program%20Files/eBahn/data/AUDI-D-D3-BD02.ebn/AUDI/D/D3/Repair%... 2/17/2014
Instrument Panel Page 40 of 43

Release securing clip - arrow 1 - on right CAN-connector.

Push retaining tab - arrow 2 - and disconnect 46-Pin CAN Connector T46b inward,
electrical wires remain connected.

Disengage and disconnect electrical harness connector on front passengers airbag - 2 -


and on Right Center Vent Motor V111 - 1 - .

Unclip wiring harness from instrument panel using Pry Lever - Rmv Outside Mirror 80-
200 - arrows - .

Unclip wiring harness from central tube for instrument panel.

x-ebahn:///C:/Program%20Files/eBahn/data/AUDI-D-D3-BD02.ebn/AUDI/D/D3/Repair%... 2/17/2014
Instrument Panel Page 41 of 43

Unscrew bottom bolt - 2 - on instrument panel.

Unscrew bolts - 1 - and - 4 - and remove supports for instrument panel central tube with
backing plates - 3 - .

Disconnect electrical harness connector on Left Center Vent Motor V110 - 1 - and on
Open-Close Display Motor V301 - 2 - .

Unscrew nuts - 1 - and - 2 - at left on central tube and remove backing plate - 3 - .

Remove bolt - 4 - .

x-ebahn:///C:/Program%20Files/eBahn/data/AUDI-D-D3-BD02.ebn/AUDI/D/D3/Repair%... 2/17/2014
Instrument Panel Page 42 of 43

Unscrew nuts - 1 - at right on central tube and remove backing plate - 3 - .

Note:

A second technician is required to remove the instrument panel central tube.

Remove central tube - 3 - with instrument panel out of vehicle interior and set it down on
a soft surface.

If necessary, detach instrument panel from central tube Instrument Panel, Separating
from Central Tube

Installing

Installation is reverse of removal, noting the following:

Align instrument panel and tighten bolt/nuts.

Bolt on steering column to central tube Suspension, Wheels, Steering - Repair Group
48 .

Observe safety precautions after connecting the battery Electrical Equipment - Repair
Group 27 .

Tightening Specifications

Component Nm
Central tube at side to body 23
Central tube to top 8
Body bottom 12
Support to Central tube 8
Body 8
Fuse holder on instrument panel central pipe 3
Relay and fuse carrier on instrument panel central pipe 3

x-ebahn:///C:/Program%20Files/eBahn/data/AUDI-D-D3-BD02.ebn/AUDI/D/D3/Repair%... 2/17/2014
Instrument Panel Page 43 of 43

Front Information Display Control Head Control Module J523 to body 4 Copyright © 2008
Audi of America,
Data bus on board diagnostic interface J533 to the body 4 Inc. and Bentley
Publishers. All rights
Center console to Body 4 reserved. Last
Instrument Panel 4 processed:

Split armrest to support foot 18


Air outlets to the rear center console 2,5
Driver-side storage compartment Central tube 4
on Instrument Panel 4
Glove compartment to Central tube 4
Instrument Panel 4

x-ebahn:///C:/Program%20Files/eBahn/data/AUDI-D-D3-BD02.ebn/AUDI/D/D3/Repair%... 2/17/2014

Das könnte Ihnen auch gefallen