Sie sind auf Seite 1von 6

5/24/2019 Types and Design of Steel Chimney Structure

Steel chimneys are structures with tall, slender and tapering with circular cross sections. They are ideally suited for process work
where a low thermal capacity required and short heat-up period. This article presents different types of steel chimneys are their
designs.

Types of Steel Chimney Structure


Types of steel chimney structure fallen under two main category which include:

1. Self-supporting steel chimneys

2. Guyed steel chimneys.

1. Self-supporting Steel Chimneys

When the lateral forces (wind or seismic forces) are transmitted to the foundation by the cantilever action of the chimney, then
the chimney is known as self-supporting chimney.

The self-supporting chimney together with the foundation remains stable under all working conditions without any additional
support.

The self-supporting chimneys are made up to 10 m diameter and from 50 m to 100m in height.

https://theconstructor.org/structural-engg/steel-chimney-types-design/980/ 1/5
5/24/2019 Types and Design of Steel Chimney Structure

Fig. 1: Self supporting steel chimney

2. Guyed Steel Chimneys

In high steel chimneys, the mild steel wire ropes or guys are attached to transmit the lateral forces. Such steel chimneys are
known as guyed steel chimneys.

In guyed steel chimneys, all the externally applied loads (wind, seismic force, etc.) are not totally carried by the chimney shell.
These attached guys or stays share these applied loads.

These guys or stays ensure the stability of the guyed steel chimney. These steel chimneys may be provided with one, two or three
sets of guys. In each set of guys, three or four or sometimes six wires are attached to the collars.

When one set of guy is used, then the guys are attached to a collar at one-third or one-fourth of the height from the top. When-
more than one set of guys are used, then these are used at various heights.

Fig. 2: Guyed steel chimney

Design of Steel Chimney Structure 


Selection of Steel Chimney 

Factors considered for selection of steel chimney type are as follows:

https://theconstructor.org/structural-engg/steel-chimney-types-design/980/ 2/5
5/24/2019 Types and Design of Steel Chimney Structure

Cost effectiveness

Number of units, equipment type, and fuel type to be used.

If chimney used for boilers, consider surface area, output efficiency, draft requirements.

Equipment operation mode

flue gas temperature before entering the chimney and its variation.

Specific weight, dust quantity, and data about flue gas aggressiveness.

local statutory regulations relating to height, ash dispersion, provision for earthing aviation warning lamp, and health.

Erection mode

Select lining type based on composition of the flue gases.

Steel Plates for Chimney


Required width of steel plates ranges between 0.9m-2.5m (1.50m most common).

Minimum steel plates thickness is 6 mm.

Thickness of steel plates in the two upper sections of the chimney is at least 8 mm to resist more corrosion at the top of chimney.

The thickness of steel plate in the flared portion should not be less than the thickness at the lowest section of the cylindrical
portion.

Available steel plates thickness are 5, 6, 8, 10, 12, 14, 16, 18, 20, 22, 25, 28, 32, 36, 40, 45, 50, 56 and 63 mm.

Breech Opening
Breech opening is also known as flue opening.

Provided for the entrance of flue gases. These gases come from furnaces of the boilers.

The area of breech opening is kept about 20 percent larger than the internal cross-sectional area of the chimney.

The maximum width of the breech opening is two-thirds of the diameter.

Reinforcement should be provided all around the breech opening to compensate for removed material.

The vertical reinforcement provided should be 20 percent larger than the material removed in the ratio of diameter to the long
chord perpendicular to the face of the opening.

The horizontal reinforcement provided at the top and bottom of the opening is kept equal to the vertical reinforcement.

The reinforcing material provides sufficient vertical stiffness.

reinforcing material should be extended above and below the opening in order to transfer and distribute the stress into the steel
of the chimney.

In the self-supporting steel chimney, the breech opening is kept well above the flared base, so that it does not extend into the
flared base.

The steel chimneys may have one breech opening, two breech openings in the same direction two breech openings at right angles
and three breech openings as shown in Fig. 3.

The width of opening does not exceed one third of the diameter of the chimney at that plane.

https://theconstructor.org/structural-engg/steel-chimney-types-design/980/ 3/5
5/24/2019 Types and Design of Steel Chimney Structure

Fig. 3: Breech opening or flue opening

Base Plate of Steel Chimney

structural steel, cast iron, or cast steel can be used as base plate for steel chimney. It is desired to employ structural steel base
plate compared with other types.

The width of steel plate should be adequate to transmit the compressive stresses to the foundation.

Thickness of base plate should be such that the bending stress and shearing stress in the base plate do not exceed the allowable
bending and shearing stresses.

Forces Acting on Steel Chimney


1. Self-weight of Steel Chimney

The self-weight of steel chimney, Ws acts vertically and expressed as:

Where:

d: chimney diameter, m

t: steel plate thickness, m

h: Height of steel chimney above the section XX in meters

79 kN/m2 is Unit weight of steel

The compressive stress in the steel plates at the section due to the self weight of chimney is equal to the 0.079 tome chimney
section height.

2. Weight of lining

The weight of the lining in the steel chimney WL, also acts vertically. The thickness of brick lining may be assumed as 100 mm.

(20 kN/m3 ) is Unit weight of brick lining in equation 2.

3. Wind Pressure

https://theconstructor.org/structural-engg/steel-chimney-types-design/980/ 4/5
5/24/2019 Types and Design of Steel Chimney Structure

The wind pressure acts horizontally and depends on the shape, width, height, location of the structure, and the climatic condition.

The wind pressure per unit area increases with the height of the structure above the ground level.

In order to simplify the design, the steel chimney is divided into number of segments of equal height. Each segment may be kept
equal up to 10 m.

The intensity of wind pressure in throughout the area of each segment may be assumed as uniform. The intensity of wind
pressure corresponding to the mid-height of each segment may be noted from IS: 875-1984.

Where:

K: Shape factor. It accounts for the shape of the structure; the shape factor for cylindrical portion is 0.7.

PI: Intensity of wind pressure

d’:  Outer diameter of the chimney

4. Seismic Forces

The seismic forces act horizontally on a structure. The following load combinations for calculations of stress at any point of steel
chimney are considered:

1. Dead load + Wind load+ Temperature effect

2. Dead load + Earthquake (seismic) load + Temperature effect

The worst combination out of the effect due to seismic (earthquake) forces and wind effect is only taken into consideration.

Bending Moment
Bending Moment on Self-supporting Steel Chimney

The wind force acts as uniformly distributed load on the self-supporting steel chimney. For the purpose of determining bending
moment at any section of steel chimney, the wind force is assumed to act at the middle height above the section.

The bending moment due to wind at a section, h metres below the top:

Stress on the extreme fibre of steel chimney due to wind is equal.

Bending Stress on Steel Chimney Due to Wind

The bending stress, fw at the extreme fibre of steel chimney due to overturning moment Mw is expressed as:

IS: 6533-1971 ‘Code of Practice for ‘Design and Construction of Steel Chimney’ recommends the value of section modulus of steel
chimney ring with no breech opening as below.

Permissible Stresses

https://theconstructor.org/structural-engg/steel-chimney-types-design/980/ 5/5

Das könnte Ihnen auch gefallen