Beruflich Dokumente
Kultur Dokumente
Copyright
This publication, including all photographs, illustrations and software, is protected
under international copyright laws, with all rights reserved. Neither this manual, nor
any of the material contained herein, may be reproduced without written consent of
the author.
Version 1.0
Disclaimer
The information in this document is subject to change without notice. The manufac-
turer makes no representations or warranties with respect to the contents hereof and
specifically disclaims any implied warranties of merchantability or fitness for any
particular purpose. The manufacturer reserves the right to revise this publication and
to make changes from time to time in the content hereof without obligation of the
manufacturer to notify any person of such revision or changes.
Trademark Recognition
Microsoft, MS-DOS and Windows are registered trademarks of Microsoft Corp.
AMD, Phenom, Athlon, Sempron and Duron are registered trademarks of AMD
Corporation.
Other product names used in this manual are the properties of their respective
owners and are acknowledged.
Declaration of Conformity
This device complies with part 15 of the FCC rules. Operation is subject to the
following conditions:
• This device may not cause harmful interference, and
• This device must accept any interference received, including interfer-
ence that may cause undesired operation.
Setting Up eJIFFY Go to
H page 55
Preface
iii
TABLE OF CONTENTS
Preface i
Chapter 1 1
Introducing the Motherboard 1
Introduction............................................................................................1
Features...................................................................................................2
Motherboard Components...................................................................4
Chapter 2 7
Installing the Motherboard 7
Safety Precautions.................................................................................7
Choosing a Computer Case..................................................................7
Installing the Motherboard in a Case.................................................7
Checking Jumper Settings....................................................................8
Setting Jumpers...............................................................................8
Checking Jumper Settings...............................................................9
Jumper Settings...............................................................................9
Installing Hardware..........................................................................10
Installing the Processor.................................................................10
Installing Memory Modules..........................................................12
Expansion Slots.............................................................................16
Connecting Optional Devices........................................................18
Installing a Hard Disk Drive/CD-ROM/SATA Hard Drive..........21
Connecting I/O Devices......................................................................23
Connecting Case Components..........................................................24
Front Panel Header.......................................................................26
Chapter 3 27
Using BIOS 27
About the Setup Utility....................................................................27
The Standard Configuration..........................................................27
Entering the Setup Utility...............................................................27
Resetting the Default CMOS Values.............................................28
Using BIOS..........................................................................................29
Standard CMOS Setup..................................................................30
Advanced Setup.............................................................................32
Advanced Chipset Setup................................................................34
iv
Integrated Peripherals..................................................................35
Power Management Setup.............................................................37
PCI/PnP Setup..............................................................................38
PC Health Status...........................................................................39
Frequency/Voltage Control............................................................43
Load Default Settings....................................................................44
Supervisor Password....................................................................44
User Password..............................................................................45
Save & Exit Setup .........................................................................45
Exit Without Saving.......................................................................45
Updating the BIOS........................................................................46
Chapter 4 47
Using the Motherboard Software 47
About the Software CD-ROM.........................................................47
Auto-installing under Windows XP/Vista.....................................47
Running Setup...............................................................................48
Manual Installation.............................................................................50
Utility Software Reference................................................................50
Chapter 5 51
Hybrid Graphics® Technology Support 51
Hybrid Graphics® Technology........................................................51
Chapter 6 55
Setting Up eJIFFY 55
Introduction........................................................................................55
Installation and BIOS Setup.............................................................56
Entering eJIFFY.........................................................................................58
Features Icons...........................................................................................59
Usage FAQ................................................................................................60
Chapter 7 67
Troulbe Shooting 67
Start up problems during assembly.................................................67
Start up problems after prolong use...................................................68
Maintenance and care tips...............................................................68
Basic Troubleshooting flowchart......................................................69
1
Chapter 1
Introducing the Motherboard
Introduction
Thank you for choosing the A785GM-M3 motherboard. This motherboard is a high
performance, enhanced function motherboard that supports socket for AMD
Phenom TM II/Phenom TM processor (socket AM2+)/Athlon TM 64 X2 Dual-Core/
AthlonTM 64/SempronTM processors for high-end business or personal desktop mar-
kets.
The motherboard incorporates the AMD 785G Northbridge (NB) and SB710
Southbridge (SB) chipsets. The Northbridge supports the HyperTransportTM 3.0 in-
terface. The memory controller supports DDR2 memory DIMM frequencies of
1066 (AM2+)/800/667/533/400. It supports two DDR2 slots with maximum memory
size of 16 GB*. One PCI Express x16 slot, intended for Graphics Interface, are fully
compliant to the PCI Express Gen2 (version 2.0). In addition, one PCI Express x1
slot is supported.
The SB710 Southbridge supports two PCI slots which are PCI v2.3 compliant. It
integrates USB 2.0 interface, supporting up to eight functional ports (four USB ports
and two USB 2.0 headers support additional four USB ports). One onboard IDE
connector supports two IDE devices in Ultra ATA 133/100/66/33 modes. The
Southbridge integrates a Serial ATA host controller, supporting six SATA ports with
maximum transfer rate up to 3.0 Gb/s each. It provides AMD SATA RAID configura-
tion with RAID 0, 1 and 10 modes supported.
There is an advanced full set of I/O ports in the rear panel, including PS/2 mouse and
keyboard connectors, COM, one VGA port, one DVI port, four USB ports, one LAN
port and audio jacks for microphone, line-in and 6/8-ch (optional) line-out.
*Due to the DRAM maximum size (2 GB per dimm) at present, the memory
maximum size we have tested is 4 GB.
Feature
Processor
This motherboard uses a socket AM2+/AM2 that carries the following features:
• Accommodates AMD PhenomTM II/PhenomTM processor (socket AM2+)/
AMD AthlonTM 64X2 Dual-Core/AthlonTM 64/Sempron™ processors
• Supports HyperTransportTM (HT) 3.0 interface speeds
HyperTransportTM Technology is a point-to-point link between two devices, it
enables integrated circuits to exchange information at much higher speeds than
currently available interconnect technologies.
Chipset
The AMD 785G Northbridge (NB) and SB710 Southbridge (SB) chipsets are based
on an innovative and scalable architecture with proven reliability and perfor-
mance.
AMD 785G • One x4 A-Link Express II interface for connection to
(NB) an AMD Southbridge
• Supports PCIe Gen 2 (version 2.0)
• Proven RadeonTM graphics powering DirectX® 10.1
• Enhanced Digital Display integration
• Fully ACPI 2.0 and IAPC (Instantly Available PC) power
management
• Single chip solution in 55nm, 1.1 V CMOS technology
• Integrated ATI Hybrid CrossFire™, ATI AvivoTM HD1,
AMD Cool'n'Quiet TM, ATI SurroundView TM, AMD
OverDrive and AMD PowerNow!
Audio (optional)
The onboard Audio provides either of the following features:
• 5.1 Channel High Definition Audio Codec
• DACs support 96K/48K/44.1KHz sample rate
• Power support: Digital:3.3V; Analog:5.0V
• WOWTM and Tru SurroundTM from SRS
• Provides single ended CD input with DRM solutions and legacy OS
issues
• 7.1+2 Channel High Definition Audio Codec
• SPDIF In/Out supports 96K/48K/44.1KHz plus SPDIF OUT supports
88.2KHz
• Power supports: Digital:3.3V; Analog:5.0V
• MAxx PlayerTM from waves
• Provides single ended CD input with DRM solutions and legacy OS
issues
Expansion Options
The motherboard comes with the following expansion options:
• One PCI Express x16 for Graphics Interface
• One PCI Express x1 slot
• Two 32-bit PCI v2.3 compliant slots
• One IDE connector supporting up to two IDE devices
• Six 7-pin SATA connectors
This motherboard supports Ultra DMA bus mastering with transfer rates of 133/
100/66/33 MB/s.
Integrated I/O
The motherboard has a full set of I/O ports and connectors:
• Two PS/2 ports for mouse and keyboard
• One serial port
• One VGA port
• One DVI port
• Four USB ports
• One LAN port
• Audio jacks for microphone, line-in and 6/8-ch (optional) line-out
BIOS Firmware
The motherboard uses AMI BIOS that enables users to configure many system
features including the following:
• Power management
• Wake-up alarms
• CPU parameters
• CPU and memory timing
The firmware can also be used to set parameters for different processor clock
speeds.
1. Some hardware specifications and software items are subject to change
without prior notice.
2. Due to chipset limitation, we recommend that motherboard be oper-
ated in the ambiance between 0 and 50 ° C.
Introducing the Motherboard
4
Motherboard Components
This concludes Chapter 1. The next chapter explains how to install the motherboard.
Memo
Chapter 2
Installing the Motherboard
Safety Precautions
• Follow these safety precautions when installing the motherboard
• Wear a grounding strap attached to a grounded device to avoid dam-
age from static electricity
• Discharge static electricity by touching the metal case of a safely
grounded object before working on the motherboard
• Leave components in the static-proof bags they came in
• Hold all circuit boards by the edges. Do not bend circuit boards
Setting Jumpers
Use the motherboard jumpers to set system configuration options. Jumpers with
more than one pin are numbered. When setting the jumpers, ensure that the jumper
caps are placed on the correct pins.
Jumper Settings
1-2: NORMAL
2-3: CLEAR
CLR_CMOS 3-pin CLEAR CMOS Before clearing the 1
CMOS, make sure to
turn the system off. CLR_CMOS
Installing Hardware
Installing the Processor
Caution: When installing a CPU heatsink and cooling fan make sure
that you DO NOT scratch the motherboard or any of the surface-
mount resistors with the clip of the cooling fan. If the clip of the
cooling fan scrapes across the motherboard, you may cause serious
damage to the motherboard or its components.
Warning:
1. Over-clocking components can adversely affect the reliability of the
system and introduce errors into your system. Over-clocking can per-
manently damage the motherboard by generating excess heat in com-
ponents that are run beyond the rated limits.
2. Always remove the AC power by unplugging the power cord from
the power outlet before installing or removing the motherboard or
other hardware components.
To achieve better airflow rates and heat dissipation, we suggest that you use
a high quality fan with 4800 rpm at least. CPU fan and heatsink installation
procedures may vary with the type of CPU fan/heatsink supplied. The form
and size of fan/heatsink may also vary.
You must install at least one module in any of the two slots. Each module can be
installed with 8 GB of memory; total memory capacity is 16 GB*.
Do not remove any memory module from its antistatic packaging until
you are ready to install it on the motherboard. Handle the modules only
by their edges. Do not touch the components or metal parts. Always
wear a grounding strap when you handle the modules.
Installation Procedure
Refer to the following to install the memory modules.
1 This motherboard supports unbuffered DDR2 SDRAM only.
2 Push the latches on each side of the DIMM slot down.
3 Align the memory module with the slot. The DIMM slots are keyed with
notches and the DIMMs are keyed with cutouts so that they can only be
installed correctly.
4 Check that the cutouts on the DIMM module edge connector match the
notches in the DIMM slot.
5 Install the DIMM module into the slot and press it firmly down until it
seats correctly. The slot latches are levered upwards and latch on to
the edges of the DIMM.
6 Install any remaining DIMM modules.
The default value is unganged mode when using socket AM2+ CPU.
2 GB Micron MT16HTF25664AY-1GAE1
Due to the Phenom CPU and memory module limitation, the DRAM may
need to adjust the voltage for supporting DDR2 1066. The memory mod-
ules which can be used stably are listed in the above QVL table for refer-
ence.
Installing the Motherboard
16
Expansion Slots
Installing Add-on Cards
The slots on this motherboard are designed to hold expansion cards and connect them
to the system bus. Expansion slots are a means of adding or enhancing the
motherboard’s features and capabilities. With these efficient facilities, you can in-
crease the motherboard’s capabilities by adding hardware that performs tasks that are
not part of the basic system.
PCIEX16 Slot The PCI Express x16 slot is used to install an external PCI
Express graphics card that is fully compliant to the PCI Express®
Generation 2.0.
PCIEX1 Slot The PCI Express x1 slot is fully compliant to the PCI Express®
Generation 2.0.
PCI1~2 Slots This motherboard is equipped with two standard PCI slots. PCI
stands for Peripheral Component Interconnect and is a bus stan-
dard for expansion cards, which for the most part, is a supple-
ment of the older ISA bus standard. The PCI slots on this board
are PCI v2.3 compliant.
For some add-on cards, for example graphics adapters and network
adapters, you have to install drivers and software before you can
begin using the add-on card.
Please make sure that the USB cable has the same pin assignment as
indicated above. A different pin assignment may cause damage or
system hang-up.
You must orient the cable connector so that the pin1 (color) edge of the
cable corresponds to the pin 1 of the I/O port connector.
IDE devices enclose jumpers or switches used to set the IDE device as MASTER or
SLAVE. Refer to the IDE device user’s manual. Installing two IDE devices on one
cable, ensure that one device is set to MASTER and the other device is set to SLAVE.
The documentation of your IDE device explains how to do this.
PS2 Mouse Use the upper PS/2 port to connect a PS/2 pointing device.
PS2 Keyboard Use the lower PS/2 port to connect a PS/2 keyboard.
Serial Port Use the COM port to connect serial devices such as mouse
(COM) or fax/modems.
LAN Port Connect an RJ-45 jack to the LAN port to connect your
computer to the network.
Audio Ports Use the three audio ports to connect audio devices. The first
(optional) jack is for stereo line-in signal. The second jack is for stereo
line-out signal. The third jack is for microphone.
Users please note that the fan connector supports the CPU cooling fan
of 1.1A~2.2A (26.4W max.) at +12V.
Chapter 3
Using BIOS
About the Setup Utility
The computer uses the latest “American Megatrends Inc. ” BIOS with support for
Windows Plug and Play. The CMOS chip on the motherboard contains the ROM
setup instructions for configuring the motherboard BIOS.
The BIOS (Basic Input and Output System) Setup Utility displays the system’s
configuration status and provides you with options to set system parameters. The
parameters are stored in battery-backed-up CMOS RAM that saves this information
when the power is turned off. When the system is turned back on, the system is
configured with the values you stored in CMOS.
The settings made in the Setup Utility affect how the computer performs. Before
using the Setup Utility, ensure that you understand the Setup Utility options.
Using BIOS
28
Note: Changes to system hardware such as different CPU, memories, etc. may also
trigger this message.
Using BIOS
29
Using BIOS
When you start the Setup Utility, the main menu appears. The main menu of the
Setup Utility displays a list of the options that are available. A highlight indicates
which option is currently selected. Use the cursor arrow keys to move the highlight
to other options. When an option is highlighted, execute the option by pressing
<Enter>.
Some options lead to pop-up dialog boxes that prompt you to verify that you wish to
execute that option. Other options lead to dialog boxes that prompt you for infor-
mation.
Some options (marked with a triangle f) lead to sub menus that enable you to change
the values for the option. Use the cursor arrow keys to scroll through the items in the
sub menu.
In this manual, default values are enclosed in parenthesis. Sub menu items are denoted
by a triangle f .
The default BIOS setting for this motherboard applies for most conditions
with optimum performance. It is not suggested to change the default
values in the BIOS setup and the manufacture takes no responsibility to
any damage caused by changing the BIOS settings.
KEY FUNCTION
ESC Exits the current menu
mnlk Scrolls through the items on a menu
+/- Modifies the selected field’s values
Enter Select
F9 Loads an optimized setting for better performance
F10 Saves the current configuration and exits setup
F1 Displays a screen that describes all key functions
Using BIOS
30
mnlk: Move Enter : Select +/-/: Value F10: Save ESC: Exit
F1: General Help F9: Optimized Defaults
Date & Time
The Date and Time items show the current date and time on the computer. If you are
running a Windows OS, these items are automatically updated whenever you make
changes to the Windows Date and Time Properties utility.
mnlk: Move Enter : Select +/-/: Value F10: Save ESC: Exit
F1: General Help F9: Optimized Defaults
Using BIOS
31
Using BIOS
32
Advanced Setup
This page sets up more advanced information about your system. Handle this page
with caution. Any changes can affect the operation of your computer.
CMOS Setup Utility - Copyright (C) 1985-2005, American Megatrends, Inc.
Advanced Setup
Help Item
HT Frequency Auto
AMD C&Q Enabled
Enhanced Halt (C1E) Disabled The HyperTransport
Quick Power on Self Test Enabled link will run at this
Boot Up Numlock Status On speed if it is slower
APIC Mode Enabled than or equal to the
1st Boot Device Hard Drive system clock and the
2nd Boot Device CD/DVD board is capable.
3rd Boot Device Removable Dev.
f Hard Disk Drive Press Enter
Boot Other Device Yes
ECS eJIFFY Function Disabled
mn < > : Move Enter : Select +/-/: Value F10: Save ESC: Exit
F1: General Help F9: Optimized Defaults
HT Frequency (Auto)
This item enables users to adjust the HT frequency. The default setting is auto and we
recommend users leave the setting unchanged. Modify it at will may cause the system
to be unstable.
AMD C&Q (Enabled)
This item helps the system to lower the frequency when CPU idles. When the
frequency decreases, the temperature will drop automatically as well.
Using BIOS
33
mnlk: Move Enter : Select +/-/: Value F10: Save ESC: Exit
F1:General Help F9: Optimized Defaults
Using BIOS
34
Help Item
DRAM Frequency Auto
DRAM Timing Mode Auto Options
Internal Graphics Mode UMA
GFX Clock Override Disabled Auto
Share Memory Size Auto Limit
Init Display First PCI Manual
HDMI Audio Enabled
DCT Unganged Mode Always
mn < > : Move Enter : Select +/-/: Value F10: Save ESC: Exit
F1: General Help F9: Opitimized Defaults
Using BIOS
35
Integrated Peripherals
This page sets up some parameters for peripheral devices connected to the system.
mn < > : Move Enter : Select +/-/: Value F10: Save ESC: Exit
F1: General Help F9: Default settings
Using BIOS
36
Using BIOS
37
Help Item
ACPI Suspend Type S3
PWRON After PWR-Fail Power Off
Resume By RING Disabled Select the ACPI
Resume By PCI/PCI-E/Lan PME Disabled state used for
Resume By USB (S3) Disabled System Suspend.
Resume By PS2 KB (S3) Disabled
Resume By PS2 MS (S3) Disabled
Resume on RTC Alarm Disabled
mnlk: Move Enter : Select +/-/: Value F10: Save ESC: Exit
F1:General Help F9: Optimized Defaults
Using BIOS
38
Help Item
Allocate IRQ to PCI VGA Yes
Options
mnlk: Move Enter : Select +/-/: Value F10: Save ESC: Exit
F1:General Help F9: Optimized Defaults
Using BIOS
39
PC Health Status
On motherboards support hardware monitoring, this item lets you monitor the
parameters for critical voltages, temperatures and fan speeds.
CMOS Setup Utility - Copyright (C) 1985-2005, American Megatrends, Inc.
PC Health Status
mn < > : Move Enter : Select +/-/: Value F10: Save ESC: Exit
F1: General Help F9: Optimized Defaults
Help Item
SMART FAN Control Enabled
SMART FAN Mode Normal
SMART Fan start PWM value 28 Normal: auto ajusts
SMART Fan start TEMP.(°C) 27 depending on the CPU
DeltaT1 +3 temperature.
SMART Fan Slope PWM value 3 PWM value/°C
CPU FAN Full Limit Temp 60°C Quiet: auto minimizes
fan speed for quiet
environment operation.
mnlk: Move Enter : Select +/-/: Value F10: Save ESC: Exit
F1:General Help F9: Optimized Defaults
Using BIOS
40
Help Item
SMART Fan Control Enabled
Smart Fan Mode Quiet
SMART Fan start PWM value 20 Normal: auto ajusts
SMART Fan start TEMP.(°C) 52 depending on the CPU
DeltaT1 +3 temperature.
SMART Fan Slope PWM value 8 PWM value/°C
CPU FAN Full Limit Temp 65°C Quiet: auto minimizes
fan speed for quiet
environment operation.
mnlk: Move Enter : Select +/-/: Value F10: Save ESC: Exit
F1:General Help F9: Optimized Defaults
Help Item
SMART Fan Control Enabled
Smart Fan Mode Quiet
SMART Fan start PWM value 20 Normal: auto ajusts
SMART Fan start TEMP.(°C) 52 depending on the CPU
DeltaT1 +3 temperature.
SMART Fan Slope PWM value 8 PWM value/°C
CPU FAN Full Limit Temp 65°C Quiet: auto minimizes
fan speed for quiet
environment operation.
mnlk: Move Enter : Select +/-/: Value F10: Save ESC: Exit
F1:General Help F9: Optimized Defaults
Using BIOS
41
Help Item
SMART Fan Control Enabled
Smart Fan Mode Silent
SMART Fan start PWM value 5 Normal: auto ajusts
SMART Fan start TEMP.(°C) 60 depending on the CPU
DeltaT1 +3 temperature.
SMART Fan Slope PWM value 14 PWM value/°C
CPU FAN Full Limit Temp 68 °C Quiet: auto minimizes
fan speed for quiet
environment operation.
mnlk: Move Enter : Select +/-/: Value F10: Save ESC: Exit
F1:General Help F9: Optimized Defaults
Help Item
SMART Fan Control Enabled
Smart Fan Mode Manual
SMART Fan start PWM value 28 Normal: auto ajusts
SMART Fan start TEMP.(°C) 27 depending on the CPU
DeltaT1 +3 temperature.
SMART Fan Slope PWM value 3 PWM value/°C
CPU FAN Full Limit Temp 60 °C Quiet: auto minimizes
fan speed for quiet
environment operation.
mnlk: Move Enter : Select +/-/: Value F10: Save ESC: Exit
F1:General Help F9: Optimized Defaults
Using BIOS
42
This item is used to set the limit temperature of the smart fan.
Using BIOS
43
Frequency/Voltage Control
This page enables you to set the clock speed and system bus for your system. The
clock speed and system bus are determined by the kind of processor you have installed
in your system.
CMOS Setup Utility - Copyright (C) 1985-2005, American Megatrends, Inc.
Frequency/Voltage Control
mn < > : Move Enter : Select +/-/: Value F10: Save ESC: Exit
F1: General Help F9: Optimized Defaults
Using BIOS
44
Supervisor Password
This page helps you install or change a password.
CMOS Setup Utility - Copyright (C) 1985-2005, American Megatrends, Inc.
Supervisor Password
mnlk: Move Enter : Select +/-/: Value F10: Save ESC: Exit
F1:General Help F9: Optimized Defaults
Using BIOS
45
User Password
This page helps you install or change a password.
mnlk: Move Enter : Select +/-/: Value F10: Save ESC: Exit
F1:General Help F9: Optimized Defaults
If you have made settings that you do not want to save, use the “Exit Without
Saving” item and select [OK] to discard any changes you have made.
Using BIOS
46
This concludes Chapter 3. Refer to the next chapter for information on the software
supplied with the motherboard.
Using BIOS
47
Chapter 4
Using the Motherboard Software
About the Software CD-ROM
The support software DVD-ROM/CD-ROM that is included in the motherboard
package contains all the drivers and utility programs needed to properly run the
bundled products. Below you can find a brief description of each software program,
and the location for your motherboard version. More information on some pro-
grams is available in a README file, located in the same directory as the software.
Before installing any software, always inspect the folder for files named
README.TXT, INSTALL.TXT, or something similar. These files may contain
important information that is not included in this manual.
1. Never try to install all software from folder that is not specified for use with
your motherboard.
2. The notice of Intel HD audio installation (optional): The Intel High Defi-
nition audio functionality unexpectedly quits working in Windows Server
2003 Service Pack 1 or Windows XP Professional x64 Edition. Users need
to download and install the update packages from the Microsoft Download
Center “before” installing HD audio driver bundled in the Driver CD.
Please log on to http://support.microsoft.com/default.aspx?scid=kb;en-
us;901105#appliesto for more information.
If the opening screen does not appear; double-click the file “setup.exe”
in the root directory.
Setup Tab
Setup Click the Setup button to run the software installation program.
Select from the menu which software you want to install.
Browse CD The Browse CD button is the standard Windows command that
allows you to open Windows Explorer and show the contents of
the support disk.
Before installing the software from Windows Explorer, look for
a file named README.TXT or something similar. This file may
contain important information to help you install the software
correctly.
Some software is installed in separate folders for different operat-
ing systems, such as Windows XP/Vista/7. Always go to the cor-
rect folder for the kind of OS you are using.
In install the software, execute a file named SETUP.EXE or
INSTALL.EXE by double-clicking the file and then following the
instructions on the screen.
Exit The EXIT button closes the Auto Setup window.
Application Tab
Lists the software utilities that are available on the disk.
Read Me Tab
Displays the path for all software and drivers available on the disk.
Running Setup
Follow these instructions to install device drivers and software for the motherboard:
1. Click Setup. The installation program begins:
The following screens are examples only. The screens and driver lists
will be different according to the motherboard you are installing.
3. Check the box next to the items you want to install. The default options are recom-
mended.
4. Click Next run the Installation Wizard. An item installation screen appears:
Manual Installation
Insert the CD in the CD-ROM drive and locate the PATH.DOC file in the root
directory. This file contains the information needed to locate the drivers for your
motherboard.
Look for the chipset and motherboard model; then browse to the directory and path
to begin installing the drivers. Most drivers have a setup program (SETUP.EXE) that
automatically detects your operating system before installation. Other drivers have
the setup program located in the operating system subfolder.
If the driver you want to install does not have a setup program, browse to the
operating system subfolder and locate the readme text file (README.TXT or
README.DOC) for information on installing the driver or software for your oper-
ating system.
Chapter 5
Hybrid Graphics® Technology Support
2. For Hybrid Graphics ® , if display by PCI-E, you must enter the BIOS, set the
Surround View in Advanced Chipset Setup to PCI-E. Then press F10 to save the
configuration and exit the BIOS. After entering OS, enter Catalyst Control Center to
enable Hybrid CrossFireTM.
While if display by OnBoard, you must enter the BIOS, set the Init Display First in
Advanced Chipset Setup to OnBoard. Then press F10 to save the configuration and
exit the BIOS. After entering OS, enter Catalyst Control Center to enable CrossFireTM.
3. Click with your right mouse button on My Computer, then click the option
Manage and choose the Device Manager, finally, click the Display Adapters. The
following screen appears. Be sure that the external ATI graphics (ATI Radeon HD
3400 Grapics) and Onboard graphics (ATI Radeon HD 3200 Series) are both display-
ing in the Display adapters.
4. Enter Catalyst Control Center, you can see the option of CrossFireTM, click it and
select Enable CrossFireTM, then Hybrid Graphics® starts.
Memo
Chapter 6
Setting Up eJIFFY
Introduction
eJIFFY is a fast boot program under Linux. Instead of waiting Windows O.S to start
execution, eJIFFY is ready to provide users the instant enjoyment on web browsing,
photo review and online chat just within several seconds after boot up.
Version: 1.0
Setting Up eJIFFY
56
3. Click the setup button to run the eJIFFY software installation program, restart
your computer after you finish.
Setting Up eJIFFY
57
4. Press <DEL> or click the BIOS Setup button on the post screen to enter the BIOS
setup page after boot up.
5. And then enter the Advanced Setup page to enable the item ECS eJIFFY Func-
tion. Press F10 to save the configuration and exit. Restart your computer.
Setting Up eJIFFY
58
Entering eJIFFY
The post screen appears within several seconds after boot up and it has three buttons
on it, Operating system, eJIFFY and BIOS Setup.
If you click eJIFFY, the following screen will appear. And If you make no choice it
will enter the normal OS automatically after ten seconds.
Setting Up eJIFFY
59
Feature Icons
The following illustration shows the main feature icons that eJIFFY provides on the
menu.
ePal: On-line chat tool to use the most popular IMs in the world. (MSN,
ICQ , AIM, etc.)
Shut Down/Restart: Ends your session and turns off the computer./Ends
your session and restart the computer..
Click once to connect the storage disk to your computer. Click for the second
time to remove your storage disk safely. (please refer to the FAQ for more
usage information.)
Setting Up eJIFFY
60
Usage FAQ
Click on the file link directly. Then select “Save File” in the pop-up window.
Note: 1. Before downloading files, please “mount” the storage devices to make
sure the device is connected with eJIFFY interface. (Please refer to the
usage FAQ to mount devices)
Setting Up eJIFFY
61
Step1.
Step2.
Setting Up eJIFFY
62
1. Select the image you want to save and press the right key of your mouse to show
the menu, then click the option “ Save Image As” from the menu.
2. Then the “Save Image” window appears. You may rename the image file in the
“Name” column and save the file in a folder as the following picture shows.
Then select a
subdirectory
Select a root or click
directory. “Create
Folder” to
create a new
folder.
Click here to
save the image
file.
Setting Up eJIFFY
63
Q1: How to find image files saved in hard disk through ePix?
Enter the ePix window, then click the icon “Folder” located in the upper left-hand
corner, then follow the path for the files you have saved to view the image files.
Setting Up eJIFFY
64
2. Click “Viewer” and choose “Keep previous zoom” in “After loading an image”.
Close the window and you can use the fit function under slide show now.
Note: ePix supports to view image files only. It cannot support Office Viewer or
other forms beside image files. Supported image types are: BMP, JPEG, GIF (includ-
ing GIF animations), PNG, TIFF, ICO and XPM.
Setting Up eJIFFY
65
Mount/Unmount Disk.
Setting Up eJIFFY
66
Memo
Setting Up eJIFFY
67
Chapter 7
Trouble Shooting
a) System does not power up and the fans are not running.
1.Disassemble the PC to remove the VGA adaptor card, DDR memory, LAN, USB
and other peripherals including keyboard and mouse. Leave only the motherboard,
CPU with CPU cooler and power supply connected. Turn on again to see if the
CPU and power supply fans are running.
2. Make sure to remove any unused screws or other metal objects such as screwdrivers
from the inside PC case. This is to prevent damage from short circuit.
4. For Intel platforms check the pins on the CPU socket for damage or bent. A bent
pin may cause failure to boot and sometimes permanent damage from short circuit.
6. Check that the 12V power & ATX connectors are fully inserted into the
motherboard connectors. Make sure the latches of the cable and connector are
locked into place.
Trouble Shooting
68
2. Check the CPU cooler fan for dust. Long term accumulation of dust will
reduce its effectiveness to cool the processor. Clean the cooler or replace a
new one if necessary.
3. Check that the 12V power & ATX connectors are fully inserted into the
motherboard connectors. Make sure the latches of the cable and connector
are locked into place.
4. Remove the hard drive, optical drive or DDR memory to determine which of
these component may be at fault.
1. Keep your computer in a well ventilated area. Leave some space between
the PC and the wall for sufficient airflow.
2. Keep your computer in a cool dry place. Avoid dusty areas, direct sunlight
and areas of high moisture content.
3. Routinely clean the CPU cooler fan to remove dust and hair.
4. In places of hot and humid weather you should turn on your computer once
every other week to circulate the air and prevent damage from humidity.
5. Add more memory to your computer if possible. This not only speeds up the
system but also reduces the loading of your hard drive to prolong its lifespan.
6. If possible, ensure the power cord has an earth ground pin directly from the
wall outlet. This will reduce voltage fluctuation that may damage sensitive devices.
Trouble Shooting
Basic Troubleshooting Flowchart
No
Check if Power Supply AC power cord is plugged No
Unit (PSU) is working and PSU switch is turned on?
Yes
No Yes
No CLR CMOS and check
Check if monitor has Any Beep sound? if CPU 12V power
display Problem with PSU or board?
is connected
If board problem -> contact RMA
Yes
Yes
Yes
Memo
Trouble Shooting