Beruflich Dokumente
Kultur Dokumente
1. Scope*
A
These designations refer to the latest issue of the respective specifications.
1.1 This specification2 covers a group of requirements
which, with the exceptions of Section 6.3, Section 14, Section 1.6 The values stated in either inch-pound units or SI units
21, and Section 22, are mandatory requirements to the ASTM are to be regarded separately as standard. Within the text, the
pipe product specifications noted below unless the product SI units are shown in brackets. The values stated in each
specification specifies different requirements, in which case the system are not exact equivalents; therefore, each system must
requirement of the product specification shall prevail. be used independently of the other. Combining values from the
two systems may result in nonconformance with the specifi-
1.2 Sections 6.3 or 21 are mandatory if the product speci- cation. The inch-pound units shall apply unless the “M”
fication has a requirement for product analysis or flattening designation (SI) of the product specification is specified in the
tests. order.
1.3 Section 22 is mandatory if the product specification has NOTE 1—The dimensionless designator NPS (nominal pipe size) has
a hydrostatic test requirement without defining the test param- been substituted in this standard for such traditional terms as “nominal
eters. diameter,” “size,” and “nominal size.”
1.4 Section 14 is for information only. 1.7 This standard does not purport to address all of the
safety concerns, if any, associated with its use. It is the
1.5 In case of conflict between a requirement of the product
responsibility of the user of this standard to establish appro-
specification and a requirement of this general requirement
priate safety and health practices and determine the applica-
specification, only the requirement of the product specification
bility of regulatory limitations prior to use.
need be satisfied.
Title of Specification ASTM DesignationA 2. Referenced Documents
Seamless Carbon Steel Pipe for High-Temperature A106/A106M 2.1 ASTM Standards:3
Service A106/A106M Specification for Seamless Carbon Steel Pipe
Metal-Arc-Welded Steel Pipe for Use With High- A381
Pressure Transmission Systems for High-Temperature Service
Seamless Carbon Steel Pipe for Atmospheric and A524 A370 Test Methods and Definitions for Mechanical Testing
Lower Temperatures of Steel Products
Centrifugally Cast Carbon Steel Pipe for High- A660
Temperature Service A381 Specification for Metal-Arc-Welded Steel Pipe for Use
Electric-Fusion-Welded Steel Pipe for Atmospheric A671/A671M With High-Pressure Transmission Systems
and Lower Temperatures A450/A450M Specification for General Requirements for
Electric-Fusion-Welded Steel Pipe for High-Pressure A672/A672M
Service at Moderate Temperatures
Carbon and Low Alloy Steel Tubes
Carbon and Alloy Steel Pipe, Electric-Fusion-Welded A691/A691M A524 Specification for Seamless Carbon Steel Pipe for
for High-Pressure Service at High Temperatures Atmospheric and Lower Temperatures
A660 Specification for Centrifugally Cast Carbon Steel Pipe
for High-Temperature Service
1
A671/A671M Specification for Electric-Fusion-Welded
This specification is under the jurisdiction of ASTM Committee A01 on Steel,
Stainless Steel and Related Alloys and is the direct responsibility of Subcommittee
Steel Pipe for Atmospheric and Lower Temperatures
A01.09 on Carbon Steel Tubular Products.
Current edition approved May 1, 2012. Published June 2012. Originally
3
approved in 1965. Last previous edition approved in 2010 as A530/ For referenced ASTM standards, visit the ASTM website, www.astm.org, or
A530M–04a(2010). DOI: 10.1520/A0530_A0530M-12. contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
2
For ASME Boiler and Pressure Vessel Code applications see related Specifi- Standards volume information, refer to the standard’s Document Summary page on
cation SA-530 in Section II of that Code. the ASTM website.
APPENDIX
(Nonmandatory Information)
SUMMARY OF CHANGES
Committee A01 has identified the location of selected changes to this specification since the last issue,
A530/A530M
(1) Revised 1.5 to delete Specifications A426, A451, A608, and (7) Revised 20.1 to require that specimens be removed from
A872. as-heat treated material.
(2) Revised Referenced Documents to add the specifications (8) Deleted the word “certified” in the phrase “certified test
listed in 1.5. report” in Section 23.
(3) Added new Section 4 and renumbered subsequent sections. (9) Deleted Note 3 and moved its contents into 23.1.
(4) Revised 6.2 to delete references to stainless steel. (10) Revised Section 23 to replace the word “certified” and the
(5) Added Test Methods A1058 to 7.1, 7.3, and Referenced word “tubes” with the word “material” and to add material and
Documents. material test in two places in 23.6.
(6) Metricated NPS designator in Sections 9 and 26.
This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years and
if not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standards
and should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of the
responsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you should
make your views known to the ASTM Committee on Standards, at the address shown below.
This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,
United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the above
address or at 610-832-9585 (phone), 610-832-9555 (fax), or service@astm.org (e-mail); or through the ASTM website
(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/
COPYRIGHT/).