Beruflich Dokumente
Kultur Dokumente
Page 1 of 4
Contents
1 Scope ................................................................2
2 Normative references ........................................2
3 Material..............................................................2
4 Additional Requirements ...................................2
5 Design ...............................................................2
5.1 Brackets on uninsulated and warm insulated
vessels ..............................................................2
5.2 Brackets on cold insulated vessels ...................4
Haag, LEHQ-ENCS1
X 05 05.2017 M. Patel, LEI-ENCS Lerzer, LEHQ-ENCS1
Alekseev, LEHQ-DQ
LEHQ / ENCS2 / LEHQ / ENCS2 / LEHQ / ENM1-S /
X 04 07.2011
John Ehrnsperger Alekseeva
X 03 10.2008 TAW-N/Bucher TAA2/Ehrnsperger TAW-N/Pertold
Status Issue Date Prepared Reviewed Approved
The reproduction, distribution and utilization of this document as well as the communication of its contents to others without express
authorization are prohibited. Offenders will be held liable for the payment of damages.
All rights reserved in the event of the grant of a patent, utility model or design.
LS 201-42 (EN)
Linde AG, Engineering Division Issue 05/05.2017 LS 201-42 Page 2 of 4
Dimensions in mm
1 Scope
This Linde Standard (LS) applies to brackets for circular platforms attached to uninsulated, warm and cold
insulated vertical vessels.
2 Normative references
This LS contains undated references to incorporate provisions of other publications. The normative references
are cited at the respective place in the text and the publications are listed below. Issues valid at the effective
date of contract shall apply.
ISO 2768-1 General tolerances – Tolerances for linear and angular dimensions without individual tolerance
indications
ISO 2553 Welding and allied processes – Symbolic representation on drawings – Welded joints
3 Material
Material of construction shall be of the same material group 1 as the material of the vessel shell with a minimum
yield strength of 235 MPa.
4 Additional Requirements
The orientation of the bracket is determined via angle indication.
The welds shall be fillet welds with throat thickness a ≥ 4 mm acc. to ISO 2553.
The lower weld of the reinforcement plate shall have a gap of 10 mm.
Tolerances according to ISO 2768 – c.
5 Design
Attachment loads on vessel for platform width up to 1200 mm: Mmax = 10 kNm, Qmax = 15 kN.
Above 1200 mm platform width, loads shall be as per project specification.
5.1 Brackets on uninsulated and warm insulated vessels
DA 100
DB 2)
S
H 1)
Ref. Line
360
3)
LS 201-42 (EN)
Linde AG, Engineering Division Issue 05/05.2017 LS 201-42 Page 3 of 4
10
D A=D B
Ref. Line
60
360
80
360
80
80
Ø25
60
The plate shall be supplied
by vessel manufacturer
3)
if necessary 150 50
DB DA
2)
S
50
Ref. Line
10
60
10
80
360
360
80
80
Ø25
60
10
2)
150+S 50
The plate shall be supplied
3) by vessel manufacturer
if necessary
60
Ref. Line
150
LS 201-42 (EN)
Linde AG, Engineering Division Issue 05/05.2017 LS 201-42 Page 4 of 4
H 1)
Ref. Line
360
Angle 3)
160
Ref. Line
D-D 21
D
10
A 60
120
10
360
360
4)
120
Clean corner
60
B
D 35 35
10
90
The plate shall be supplied
by vessel manufacturer 50 160
3)
if necessary 10
S
A B
7
60
°
45
3 4
10
3
Figure 5: Bracket on cold insulated vessels - Details
LS 201-42 (EN)