Beruflich Dokumente
Kultur Dokumente
CRRFTSMRN°
ROTARY LAWN MOWER
650 Series Briggs & Stratton Engine
Power-Propelled
Electric Start
22" Multi-Cut
Model No.
917.376742
• EspaSol, p. 21
CAUTION:
Read and follow all
Safety Rules and Instructions
before operating this equipment
This warranty applies only while this product is used in the United States.
This warranty gives you specific legal rights, and you may also have other rights which
vary from state to state.
Sears, Roebuck and Co., Hoffman Estates, IL 60179
IMPORTANT: This cutting machine is capable of amputating hands and feet and throw-
ing objects. Failure to observe the following safety instructions could result in serious
injury or death.
_,Look for this symbol to point out impor- AWARNING: Battery posts, terminals and
tant safety precautions. It means related accessories contain lead and lead
CAUTIONH! BECOME ALERTN! compounds, chemicals known to the State
YOUR SAFETY IS INVOLVED. of California to cause cancer and birth
defects or other reproductive harm. Wash
_i, WARNING: In order to prevent ac- hands after handling.
cidental starting when setting up, trans-
porting, adjusting or making repairs, A CAUTION: Muffler and other engine
always disconnect spark plug wire and parts become extremely hot during
place wire where it cannot come in contact operation and remain hot after engine has
with plug. stopped. To avoid severe burns on contact,
stay away from these areas.
_WARNING: Engine exhaust, some of its
constituents, and certain vehicle components
contain or emit chemicals known to the State
of California to cause cancer and birth defects
or other reproductive harm.
I. GENERAL OPERATION • Always wear safety goggles or safety
• Read, understand, and follow all glasses with side shields when operating
instructions on the machine and in the mower.
manual(s) before starting. Be thoroughly II. SLOPE OPERATION
familiar with the controls and the proper
Slopes are a major factor related to slip &
use of the machine before starting. fall accidents which can result in severe in-
• Do not put hands or feet near or under
jury. All slopes require extra caution. If you
rotating parts. Keep clear of the dis-
feel uneasy on a slope, do not mow it.
charge opening at all times.
DO:
• Only allow responsible individuals, who
are familiar with the instructions, to oper- • Mow across the face of slopes: never
ate the machine. up and down. Exercise extreme caution
• Clear the area of objects such as rocks, when changing direction on slopes.
toys, wire, bones, sticks, etc., which • Remove obstacles such as rocks, tree
could be picked up and thrown by blade. limbs, etc.
• Be sure the area is clear of other people • Watch for holes, ruts, or bumps. Tall
before mowing. Stop machine if anyone grass can hide obstacles.
enters the area. DO NOT:
• Do not operate the mower when bare- • Do not trim near drop-offs, ditches or
foot or wearing open sandals. Always embankments. The operator could lose
wear substantial foot wear. footing or balance.
• Do not pull mower backwards unless • Do not trim excessively steep slopes.
absolutely necessary. Always look down • Do not mow on wet grass. Reduced foot-
and behind before and while moving ing could cause slipping.
backwards.
III. CHILDREN
• Never direct discharged material toward
anyone. Avoid discharging material Tragic accidents can occur if the operator
against a wall or obstruction. Material is not alert to the presence of children.
may richochet back toward the opera- Children are often attracted to the machine
tor. Stop the blade when crossing gravel and the mowing activity. Never assume
surfaces. that children will remain where you last
• Do not operate the mower without saw them.
proper guards, plates, grass catcher or • Keep children out of the trimming area
other safety protective devices in place. and under the watchful care of another
• See manufacturer's instructions for responsible adult.
proper operation and installation of • Be alert and turn machine off if children
accessories. Only use accessories ap- enter the area.
proved by the manufacturer. • Before and while walking backwards,
• Stop the blade(s) when crossing gravel look behind and down for small children.
drives, walks, or roads. • Never allow children to operate the ma-
• Stop the engine (motor) whenever you chine.
leave the equipment, before cleaning the • Use extra care when approaching blind
mower or unclogging the chute. corners, shrubs, trees, or other objects
• Shut the engine (motor) off and wait until that may obscure vision.
the blade comes to complete stop before IV. SAFE HANDLING OF GASOLINE
removing grass catcher.
Use extreme care in handling gasoline.
• Mow only in daylight or good artificial
Gasoline is extremely flammable and the
light.
vapors are explosive.
• Do not operate the machine while under
• Extinguish all cigarettes, cigars, pipes
the influence of alcohol or drugs.
and other sources of ignition.
• Never operate machine in wet grass.
• Use only an approved container.
Always be sure of your footing: keep a
• Never remove gas cap or add fuel with
firm hold on the handle; walk, never run.
the engine running. Allow engine to cool
• Disengage the self-propelled mech-
anism or drive clutch on mowers so before refueling.
• Never refuel the machine indoors.
equipped before starting the engine.
• Never store the machine or fuel contain-
• If the equipment should start to vibrate
er where there is an open flame, spark
abnormally, stop the engine (motor) and
or pilot light such as a water heater or on
check immediately for the cause. Vibra-
other appliances.
tion is generally a warning of trouble.
• Neverfill containersinsidea vehicle, on• Keepnuts and bolts, especiallyblade
a truck or trailer bedwith a plasticliner.
attachmentbolts, tight and keepequip-
Always place containerson the ground mentin good condition.
awayfrom yourvehicle beforefilling. • Nevertamperwith safetydevices.Check
• Removegas-poweredequipmentfrom their proper operationregularly.
the truck or trailerand refuel it on the
• Keepmachinefree of grass, leaves,or
ground. If this is not possible,then other debris build-up.Cleanoil or fuel
refuelsuch equipmentwith a portable spillage.Allow machineto coolbefore
container,ratherthan from a gasoline storing.
dispensernozzle. • Stop and inspectthe equipmentif you
• Keepthe nozzle in contactwith the rim strike an object. Repair,if necessary,
of the fuel tank or containeropeningat beforerestarting.
all times untilfueling is complete. Do• Neverattemptto makewheel height
not use a nozzlelock-opendevice. adjustmentswhile the engine is running.
• If fuel is spilled on clothing,change • Grasscatchercomponentsare subject
clothingimmediately. to wear, damage,anddeterioration,
• Neveroverfillfuel tank. Replacegas which could expose movingparts or
cap and tightensecurely. allowobjectsto be thrown.Frequently
checkcomponentsand replacewith
V. GENERAL SERVICE manufacturer'srecommendedparts,
when necessary.
• Neverrun a machineinsidea closed • Mowerbladesare sharpand can cut.
area. Wrap the blade(s)or wear gloves,and
• Nevermakeadjustmentsor repairswith useextra cautionwhen servicingthem.
the engine (motor)running.Disconnect • Do not changethe enginegovernorset-
the spark plug wire, and keepthe wire ting or overspeedthe engine.
awayfromthe plug to preventaccidental • Maintainor replacesafetyand instruc-
starting. tion labels,as necessary.
AWARNING: This lawn mower is equipped with an internal combustion engine and
should not be used on or near any unimproved forest-covered, brush-covered or
grass-covered land unless the engine's exhaust system is equipped with a spark
arrester meeting applicable local or state laws (if any). If a spark arrester is used, it
should be maintained in effective working order by the operator.
In the state of California the above is required by law (Section 4442 of the California
Public Resources Code). Other states may have similar laws. Federal laws apply on
federal lands. A spark arrester for the muffler is available through your nearest Sears
Parts & Repair Center (See the REPAIR PARTS section of this manual).
Serial Number:
Date of Purchase:
• The model and serial numbers will be found on a decal on the rear of the lawn mower
housing. Record both serial number and date of purchase in space provided above.
4
Repair Protection Agreements
Congratulations on making a smart pur- • Fast help by phone- phone sup-
chase. Your new Craftsman® product is port from a Sears representative on
designed and manufactured for years of products requiring in-home repair, plus
dependable operation. But like all prod- convenient repair scheduling.
ucts, it may require repair from time to Once you purchase the Agreement, a
time. That's when having a Repair Protec- simple phone call is all that it takes for you
tion Agreement can save you money and to schedule service. You can call anytime
aggravation. day or night, or schedule a service ap-
pointment online.
Purchase a Repair Protection Agreement Sears has over 12,000 professional repair
now and protect yourself from unexpected specialists, who have access to over 4.5
hassle and expense. million quality parts and accessories.
That's the kind of professionalism you can
Here's what's included in the Agreement: count on to help prolong the life of your
• Expert service by our 12,000 profe- new purchase for years to come. Purchase
sional repair specialists. your Repair Protection Agreement today!
• Unlimited service and no charge for Some limitations and exclusions apply.
parts and labor on all covered repairs. For prices and additional information
• Product replacement if your covered call 1-800-827-6655.
product can't be fixed.
• Discount of 10% from regular price of Sears Installation Service
service and service-related parts not For Sears professional installation of home
covered by the agreement; also, 10% appliances, garage door openers, water
off regular price of preventive mainte- heaters, and other major home items, in
nance check. the U.S.A. call 1-800-4-MY-HOME®.
These accessories were available when this lawn mower was produced. They are not
shipped with your mower. They are also available at most Sears retail outlets and
service centers. Some of these accessories may not apply to your lawn mower.
LAWN MOWER PERFORMANCE
CLIPPING
DEFLECTORS
FOR STABILIZER
REAR DISCHARGE
LAWN MOWERS
Lower handle
TO ASSEMBLE GRASS CATCHER TO PREPARE BATTERY
1. Put grass catcher frame into grass bag NOTE: Your battery must be charged
with rigid part of bag on the bottom. before you can start your lawn mower.
Make sure the frame handle is outside 1. Connect battery charger connector
of the bag top. (male) to harness connector (female).
2. Slip vinyl bindings over frame. 2. Plug battery charger into 110 volt A.C.
NOTE: If vinyl bindings are too stiff, hold outlet.
them in warm water for a few minutes. If 3. Leave battery charger connected for
bag gets wet, let it dry before using. 24 hours before starting your engine
for the first time.
4. After charging, disconnect harness
connector (female) from battery char-
ger connector (male).
Connect your battery charger to charge
battery after each use.
IMPORTANT: The engine will not re-
charge your battery.
At the end of the mowing season the
battery should be charged for 48 hours to
,_otect the battery during winter storage.
CAUTION: Always disconnect the
engine connector (male) from the battery
connector (female) to prevent accidental
Vinyl Frame
starting when transporting or storing your
bindings opening lawn mower after the season.
Engine Harness
\\
connector connector
ale)
\
\
\
Charger
connector (male)
TO INSTALL ATTACHMENTS
Your lawn mower was shipped ready to be
used as a mulcher. To convert mower to
bagging or discharging, see "TO CON-
VERT MOWER" in the Operation section
of this manual.
KNOW YOUR LAWN MOWER
READ THIS OWNER'S MANUAL AND ALL SAFETY RULES BEFORE OPERATING
YOUR LAWN MOWER. Compare the illustrations with your lawn mower to familiarize
yourself with the location of various controls and adjustments. Save this manual for
future reference.
These symbols may appear on your lawn mower or in literature supplied with the
product. Learn and understand their meaning.
CAUTION ENGINE ENGINE FAST SLOW CHOKE FUEL OIL DANGER, KEEP HANDS
OR WARNING ON OFF AND FEET AWAY
Drive
control - Operator presence control bar
bar
Handle knob
Key
start
switch
Grass Primer
catcher
Muffler
Gasoline
filler cap .......
plug
Housing .......
Air filter
Operator presence control bar - must Auxiliary starter handle - used for start-
be held down to the handle to start the ing engine.
engine. Release to stop the engine. Mulcher door - allows conversion to
Primer- pumps additional fuel from the discharging or bagging operation.
carburetor to the cylinder for use when Drive control bar - used to engage
starting a cold engine. power-propelled forward motion of mower.
Key start switch - used for starting engine. 8
The operationof any O presence control bar
SAFETY
GLASSES lawn mowercan result
in foreign objectsthrown
into the eyes,which can
result in severe eye dam- Drive
age.Alwayswearsafetyglasses or eye control bar
shieldswhile operatingyour lawn mower
or performingany adjustmentsor repairs. DRIVE
We recommenda standardsafetyglasses CONTROL
or wide vision safetymaskworn over DISENGAGED
spectacles.
Engine speed was set at the factory for DRIVE CONTROL ADJUSTMENT
optimum performance. It is not adjustable.
Over time, the drive control system may
become "loose", resulting in decreased
ENGINE ZONE CONTROL speed. There are holes in the drive
_I_CAUTION: Federal regulations require control housing to increase tension on the
an engine control to be installed on this drive cable. Proceed as follows:
lawn mower in order to minimize the risk 1. Turn unit off and disconnect spark plug
of blade contact injury. Do not under wire from spark plug.
any circumstances attempt to defeat the 2. Loosen nut, move drive control hous-
function of the operator control. The blade ing down handle to the next hole and
turns when the engine is running. retighten nut.
• Your lawn mower is equipped with an 3. Operate mower to test drive speed.
operator presence control bar which 4. If condition fails to improve after the
requires the operator to be positioned above steps (forward speed remains
behind the lawn mower handle to start the same), your drive belt is worn and
and operate the lawn mower. should be replaced.
• Self-propelling is controlled by hold- Raise wheels for low cut and lower wheels
ing the operator presence control bar for high cut, adjust cutting height to suit
down to the handle and pulling the drive your requirements. Medium position is
control bar up to the handle. The closer best for most lawns.
to the handle the bar is pulled, the faster • To change cutting height, squeeze ad-
the unit will travel. juster lever toward wheel. Move wheel
• Forward motion will stop when either up or down to suit your requirements.
the operator presence control bar or Be sure all wheels are in the same set-
drive control bar are released. To stop ting.
forward motion without stopping engine, NOTE: Adjuster is properly positioned
release the drive control bar only. Hold when plate tab inserts into hole in lever.
operator presence control bar down Also, 9-position adjusters (if so equipped)
against handle to continue mowing allow lever to be positioned between the
without self-propelling plate tabs.
NOTE: If after releasing the drive control LEVER BACKWARD Plate tab
the mower will not roll backwards, push TO LOWER MOWER
the mower forward slightly to disengage
drive wheels.
• To keep drive control engaged when
turning corners, push down on the
handle to lift the front wheels off the
ground while turning lawn mower.
LEVER FORWARD TO RAISE MOWER Lever
TO CONVERTMOWER /
FOR MULCHING -
1. Rear mulcher plug installed.
2. Mulcher door closed.
FOR REAR BAGGING -
Mulcher 1. Rear mulcher plug removed.
2. Grass catcher installed.
3. Mulcher door closed.
FOR SIDE DISCHARGING -
SIDE DISCHARGING
1. Rear mulcher plug installed.
• Mulcher plug must be installed into rear 2. Discharge deflector installed.
discharge opening of mower.
• Open mulcher door and install dis- _I_CAUTION: Do not run your lawn
charge deflector under door as shown. mower without mulcher plug or approved
• Mower is now ready for discharging grass catcher in place. Never attempt to
operation. operate the lawn mower with the rear door
• To convert to mulching or bagging removed or propped open.
operation, discharge deflector must be
removed and mulcher door closed. TO EMPTY GRASS CATCHER
\ / 1. Lift up on grass catcher using the
frame handle.
2. Remove grass catcher with clippings
from under lawn mower handle.
3. Empty clippings from bag.
NOTE: Do not drag the bag when empty-
ing; it will cause unnecessary wear.
Grass
catcher
I frame
I
Open mulcher door
Discharge deflector
10
BEFORE STARTING ENGINE
Engine
ADD OIL oil cap
Your lawnmower is shipped without oil in
the engine. For type and grade of oil to
use, see "ENGINE" in the Maintenance
section of this manual.
A CAUTION: DO NOT overfill engine with
oil, or it will smoke heavily from the muffler
on startup. Gasoline
1. Be sure lawnmower is level.
filler cap
2. Remove oil dipstick from oil fill spout.
3. You receive a container of oil with the
unit. Slowly pour the entire container Primer
down the oil fill spout into the engine.
NOTE: Initial oil fill requires only 18 oz.
TO STOP ENGINE
due to residual oil in engine from the
manufacturers 100% quality testing. When • To stop engine, release operator pres-
changing oil you may need 20 oz. ence control bar.
4. Insert and tighten dipstick.
IMPORTANT:
TO START ENGINE
• Check oil level before each use. Add oil
NOTE: Due to protective coatings on the
if needed. Fill to full line on dipstick.
engine, a small amount of smoke may be
• Change the oil after every 25 hours of
present during the initial use of the product
operation or each season. You may
and should be considered normal.
need to change the oil more often
1. To start a cold engine, push primer
under dusty, dirty conditions. See "TO
CHANGE ENGINE OIL" in the Mainte- three (3) times before trying to start.
nance section of this manual. Use a firm push. This step is not usu-
ally necessary when starting an engine
which has already run for a few minutes.
ADD GASOLINE
2. Hold operator presence control bar
• Fill fuel tank to bottom of tank filler neck. down to the handle and turn the start
Do not overfill. Use fresh, clean, regular key.
unleaded gasoline with a minimum of IMPORTANT: Do not crank engine more
87 octane. Do not mix oil with gasoline. than five continous seconds between each
Purchase fuel in quantities that can be time you try to start. Wait 5 to 10 seconds
used within 30 days to assure fuel fresh- between each attempt.
ness. • To start engine using the rope starter,
A CAUTION: Wipe off any spilled oil or follow the steps above. Exchange the
fuel. Do not store, spill or use gasoline use of the starter rope for start key.
near an open flame. Pull starter handle quickly. Do not allow
A_, CAUTION: Alcohol blended fuels
starter rope to snap back.
(called gasohol or using ethanol or metha- NOTE: In cooler weather it may be neces-
nol) can attract moisture which leads to sary to repeat priming steps. In warmer
separation and formation of acids during weather over priming may cause flooding
storage. Acidic gas can damage the fuel and engine will not start. If you do flood
system of an engine while in storage. To engine wait a few minutes before at-
avoid engine problems, the fuel system tempting to start and do not repeat priming
should be emptied before storage of 30 steps.
days or longer. Empty the gas tank, start
the engine and let it run until the fuel lines
and carburetor are empty. Use fresh fuel
next season. See Storage Instructions for
additional information. Never use engine
or carburetor cleaner products in the fuel
tank or permanent damage may occur.
11
MOWING TIPS MULCHING MOWING TIPS
A& CAUTION: Do not use de-thatcher IMPORTANT: For best performance,
blade attachments on your mower. Such keep mower housing free of built-up
attachments are hazardous, will damage grass and trash. See "CLEANING" in the
your mower and could void your warranty. Maintenance section of this manual.
• Under certain conditions, such as very • The special mulching blade will recut
tall grass, it may be necessary to raise the grass clippings many times and
the height of cut to reduce pushing effort reduce them in size so that as they fall
and to keep from overloading the engine onto the lawn they will disperse into
and leaving clumps of grass clippings. the grass and not be noticed. Also, the
It may also be necessary to reduce mulched grass will biodegrade quickly to
ground speed and/or run the lawn provide nutrients for the lawn. Always
mower over the area a second time. mulch with your highest engine (blade)
• For extremely heavy cutting, reduce the speed as this will provide the best recut-
width of cut by overlapping previously ting action of the blades.
cut path and mow slowly. • Avoid cutting your lawn when it is wet.
• For better grass bagging and most cut- Wet grass tends to form clumps and
ting conditions, the engine speed should interferes with the mulching action. The
be set in the FAST position. best time to mow your lawn is the early
• Pores in cloth grass catchers can afternoon. At this time the grass has
become filled with dirt and dust with use dried, yet the newly cut area will not be
and catchers will collect less grass. To exposed to direct sunlight.
prevent this, regularly hose catcher off • For best results, adjust the lawn mower
with water and let dry before using. cutting height so that the lawn mower
• Keep top of engine around starter clear cuts off only the top one-third of the
and clean of grass clippings and chaff. grass blades. If the lawn is overgrown
This will help engine air flow and extend it will be necessary to raise the height of
engine life. cut to reduce pushing effort and to keep
from overloading the engine and leaving
clumps of mulched grass. For extremely
heavy grass, reduce your width of cut
by overlapping previously cut path and
mow slowly.
1/3
12
BEFORE AFTER EVERY EVERY EVERY
EACH EACH 10 25HOURS 100 BEFORE
SCHEDULE USE USE HOURS OR SEASON HOURS STORAGE
_ Check Tires
N Check Drive Wheels ***
Clean Lawn Mower ....
M Clean under Drive Cover ***
O Check Drive Belt / Pulleys ***
_ Inspect Muffler I/
N Replace Spark Plug
E Replace Air Filter Paper Cartridge
Empty fuel system or add Stabilizer I/
* (if so equipped) 1 - Change more often if operating under a heavy load or in high outdoor temperatures.
** Electric-Start mowers 2 - Service more often if operating in dirty or dusty conditions.
*** Power-Propelled mowers 3 - Replace blades more often when mowing in sandy soil,
**** Use a scraper 4 - Charge 48 hours at end of season.
to clean under deck 5 - And after each 5 hours of use.
LAWN MOWER
TO ADJUST CUTTING HEIGHT TO REPLACE DRIVE BELT
See "TO ADJUST CUTTING HEIGHT" in 1. Place new drive belt in engine pulley
the Operation section of this manual. and belt retainer of debris shield.
2. Route the other end of the new drive
REAR DEFLECTOR belt through hole in housing.
3. Reinstall debris shield.
The rear deflector, attached between the
4. Reinstall blade.
rear wheels of your mower, is provided to
minimize the possibility that objects will 5. Return mower to upright position.
be thrown out of the rear of the mower 6. Push down on arm, install new belt on
into the operator mowing position. If the gearcase pulley. Release arm slowly.
deflector becomes damaged, it should be NOTE: Always use factory approved belt
replaced. to assure proper fit and long life.
7. Reinstall drive cover.
TO REMOVE DRIVE BELT Engine pulley
1. Remove drive cover.
2. Remove belt from gearcase pulley by
pushing down on arm and rolling belt
off pulley. Drive belt
3. Turn lawn mower on its side with air
filter and carburetor down.
4. Remove blade, engine pulley and
debris shield.
5. Remove engine pulley and belt from
debris shield.
Belt
retainer
Debris shield
16
TO ADJUST HANDLE
The handle can be mounted in a high or
low position. The mounting holes in the
bottom of lower handle are off center for
raising or lowering the handle.
1. Remove upper handle and wire tie(s)
securing cable(s) to lower handle.
2. Remove trimplate from lower handle.
Trimplate
ENGINE
ENGINE SPEED
Your engine speed has been factory set.
, Remove hairpin cotters from lower Do not attempt to increase engine speed
handle bracket mounting pin. or it may result in personal injury. If you
believe that engine is running too fast or
too slow, take your mower to a Sears or
Mowing Mowing
position position other qualified service center for repair
and adjustment.
CARBURETOR
Your carburetor is not adjustable. If your
engine does not operate properly due
Hairpin to suspected carburetor problems, take
Handle
your lawn mower to a Sears or other
Mounting, qualified service center for repair and/or
pin adjustment.
LOW POSITION HIGH POSITION IMPORTANT: Never tamper with the
engine governor, which is factory set for
4. Squeeze lower handle in to remove it proper engine speed. Overspeeding
from mounting pins. the engine above the factory high speed
5. Turn lower handle over to raise or setting can be dangerous. If you think
lower handle. the engine-governed high speed needs
6. Squeeze lower handle in and position adjusting, contact a Sears or other
holes onto mounting pins on handle qualified service center, which has proper
bracket. equipment and experience to make any
7. Reassemble trimplate to lower handle. necessary adjustments.
8. Reassemble upper handle and all parts
removed from lower handle.
Immediately prepare your lawn mower for 1. Clean entire lawn mower (See
storage at the end of the season or if the "CLEANING" in the Maintenance sec-
unit will not be used for 30 days or more. tion of this manual).
2. Lubricate as shown in the Maintenance
LAWN MOWER
section of this manual.
When lawn mower is to be stored for a
3. Be sure that all nuts, bolts, screws, and
period of time, clean it thoroughly, remove pins are securely fastened. Inspect
all dirt, grease, leaves, etc. Store in a moving parts for damage, breakage
clean, dry area.
17 and wear. Replace if necessary.
4. Touchup all rustedor chippedpaint gas can damagethe fuel systemof an
surfaces;sand lightly beforepainting. enginewhile in storage.
• Emptythe fuel tank by startingthe en-
HANDLE gine and lettingit run until the fuel lines
Youcanfoldyourmowerhandleforstorage. andcarburetorare empty.
1. Squeezethe bottomends of the lower • Neveruseengine or carburetorcleaner
handletowardeach other untilthe productsin the fuel tank or permanent
lower handleclearsthe handlebracket, damage mayoccur.
then movehandleforward. • Usefresh fuel next season.
2. Loosenupper handlemountingbolts NOTE: Fuel stabilizer is an acceptable
enoughto allow upperhandleto be alternative in minimizing the formation of
folded back. fuel gum deposits during storage. Add
IMPORTANT:When foldingthe handlefor stabilizerto gasolinein fuel tank or storage
storageor transportation,be sure to fold container.Alwaysfollowthe mixratiofound
the handleas shown or you may damage on stabilizercontainer. Runengineat least
the controlcables. 10 minutesafter adding stabilizerto allow
• Whensetting up your handlefrom the thestabilizertoreachthe carburetor.Donot
storageposition,the lowerhandlewill empty the gas tank and carburetorif using
automaticallylock into mowingposition. fuel stabilizer.
SQUEEZE ENGINE OIL
TO FOLD Drain oil (with engine warm) and replace
Lower handle-"""- with clean engine oil. (See "ENGINE" in
the Maintenance section of this manual).
CYLINDER
1. Remove spark plug.
L
2. Pour one ounce (29 ml) of oil through
spark plug hole into cylinder.
3. Pull starter handle slowly a few times
Operator MOWING to distribute oil.
I: POSITION
control bar 4. Replace with new spark plug.
B ATT E RY
Disconnect the battery from the engine
FOLD ,J X connector and charge battery 48 hours.
FORWARD Upper
FOR '\ handle OTHER
STORAGE
• Do not store gasoline from one season
to another.
Handle • Replace your gasoline can if your can
knob starts to rust. Rust and/or dirt in your
gasoline will cause problems.
• If possible, store your unit indoors and
Lower handle cover it to protect it from dust and dirt.
• Cover your unit with a suitable protec-
tive cover that does not retain moisture.
ENGINE
Do not use plastic. Plastic cannot
FUEL SYSTEM breathe, which allows condensation to
IMPORTANT: It is important to prevent form and will cause your unit to rust.
gum deposits from forming in essential IMPORTANT: Never cover mower while
fuel system parts such as carburetor, fuel engine and exhaust areas are still warm.
filter, fuel hose, or tank during storage. _CAUTION: Never store the lawn
Alcohol blended fuels (called gasohol or mower with gasoline in the tank inside a
using ethanol or methanol) can attract building where fumes may reach an open
moisture which leads to separation and flame or spark. Allow the engine to cool
formation of acids during storage. Acidic before storing in any enclosure.
18
TROUBLESHOOTING - See appropriate section in manual unless directed
to a Sears Parts & Repair Center,
PROBLEM CAUSE CORRECTION
Does not start 1. Dirty air filter. 1. Clean/replace air filter.
2. Out of fuel. 2. Fill fuel tank.
3. Stale fuel. 3.
Empty fuel tank and refill tank
with fresh, clean gasoline.
4. Water in fuel. 4. Empty fuel tank and refill tank
with fresh, clean gasoline.
5. Spark plug wire is 5. Connect wire to plug.
disconnected.
6. Bad spark plug. 6. Replace spark plug.
7. Loose blade or broken 7. Tighten blade bolt or
blade adapter. replace blade adapter.
19
TROUBLESHOOTING - See appropriate section in manual unless directed
to a Sears Parts & Repair Center,
PROBLEM CAUSE CORRECTION
20
Garantia ......................................................... 21 Mantenimiento .......................................... 31-35
Reglas de Seguridad ................................ 21-23 Servicio y Adjustes ................................... 35-36
Especificaciones del Producto ....................... 23 Almacenamiento ....................................... 36-37
Montaje / Pre-Operaci6n .......................... 25-26 Identificaci6n de problemas ...................... 38-39
Operaci6n ................................................. 27-31 Partes de repuesto .................................. 40-49
Programa de Mantenimiento ......................... 31 Servicio Sears .................................. Contratapa
Si esta Segadora Craftsman Ilega a presentar algQn desperfecto por defectos de materiales
o fabricaci6n durante un plazo de dos aSos a partir de la fecha de compra, Ilevela de vuelta a
cualquiera de las tiendas Sears, al Centro de Repuestos y Reparaci6n, o a otro comercio donde se
vendan los equipos Craftsman, a efectos de que se la reparen sin costo (o bien se la reemplacen,
en caso que no sea posible repararla).
Si esta Segadora Ilega a ser utilizada con fines comerciales o arrendada, la presente garantia tendra
vigencia por s61o 90 dias a partir de la fecha de compra.
La presente garantia no cubre:
• Aquellas piezas fungibles que se desgastan por el uso normal, tales como las cuchillas rotatorias
de la cortadora, los adaptadores de las cuchillas, las correas, los filtros de aire y las bujias.
• Aquellas reparaciones que haya que hacer debido a mal uso o negligencia por parte del operador,
incluidos el arbol del cigQeSal torcido u omisiones relativas al armado, manejo o mantenimieno de
la Segadora en un todo de acuerdo alas instrucciones provistas con el equipo.
La presente garantia se aplicara solamente en tanto el articulo sea usado en los Estados Unidos.
Esta garantia le otorga a usted derechos legales especificos; puede que usted tenga, ademas, otros
derechos, los cuales varian de estado a estado.
Sears, Roebuck and Co., Hoffman Estates, IL 60179
IMPORTANTE: Esta maquina cortadaora es capaz de amputar las manos y los manos y los pies y
de lanzar objetos. Si no se observan las instrucciones de seguridad siguientes se pueden producir
lesiones graves o la muerte.
_lbBusque este simbolo que se5ala las precau- A0kPRECAUCI(SN: El tubo de escape del motor,
ciones de seguridad de importancia. Quiere algunos de sus constituyentes y algunos com-
decir - jiiATENCION!!! ijiESTE ALERTO!!! ponentes del vehiculo contienen o desprenden
SU SEGURtDAD ESTA COMPROMETIDA. productos quimicos conocidos en el Estado de
California como causa de cancer y defectos al
_ADVERTENClA: Siempre desconecte el nacimiento u otros da5os reproductivos.
alambre de la bujia y p6ngalo donde no pueda
entrar en contacto con la bujia, para evitar el _,PRECAUCI(_)N: El silenciador y otras piezas
arranque por accidente, durante la preparaci6n, del motor Ilegan a sre extremadamente calien-
el transporte, el ajuste o cuando se hacen tes durante la operaci6n y siguen siendo cali-
reparaciones. entes despues de que el motor haya parado.
Para evitar quemaduras severas, permanezca
dlI_ADVERTENClA: Los bornes, terminales y lejos de estas areas.
accesorios relativos de la bateria contienen
plomo o compuestos de plomo, productos
quimicos conocidos en el Estado de California
como causa de cancer y defectos al nacimiento
u otros da5os reproductivos. Lavar las manos
despues de manipularlos.
"I
21
I. OPERACION • Siempre use gafas de seguridad o anteojos
• Antes de empezar, debe familiarizarse con protecci6n lateral cuando opere la sega-
completamente con los controles y el uso dora.
correcto de la maquina. Para esto, debe leer
y comprender todas las instrucciones que II. OPERACION SOBRE LAS CUESTAS
aparecen en la maquina yen los manuales Los accidentes ocurren con mas frecuencia en
de operacion. las cuestas. Estos accidentes ocurren debido a
• No ponga las manos o los pies cerca o resbaladas o caidas, las cuales pueden resultar
debajo de las partes rotatorias. Mantengase en graves lesiones. Operar la recortadora en
siempre lejos de la abertura de la descarga. cuestas requiere mayor concentraci6n. Si se
• Permita que solamente las personas re- siente inseguro en una cuesta, no la recorte.
sponsables que esten familiarizadas con las HACER:
instrucciones operen la maquina.
• Puede recortar a traves de la superficie de
• Despeje el area de objetos tales como pie-
la cuesta, nunca hacia arriba y hacia abajo.
dras, juguetes, alambres, huesos, palos, etc.
que pueden ser recogidos y lanzados por las Proceda con extrema precaucion cuando
cuchillas. cambie de direcci6n en las cuestas.
• AsegQrese que el area no se hallen per- • Renueva todos los objetos extra5os, tales
sonas, antes de segar. Pare la maquina si como guijarros, ramas, etc.
alguien entra en el area. • Debe prestar atencion a hoyos, baches o
• No opere la maquina sin zapatos o con protuberancias. Recuerde que la hierba alta
sandalias abiertas. P6ngase siempre zapatos puede esconder obstaculos.
s61idos. NO HACER:
• No tire de la segadora hacia atras a menos • No recorte cerca de pendientes, zanjas o
que sea absolutamente necesario. Mire terraplenes. El operador puede perder la
siempre hacia abajo y hacia detras antes y traccion en los pies o el equilibrio.
mientras que se mueve hacia atras. • No recorte cuestas demasiado inclinadas.
• Nunca dirigir el material descargado hacia • No recorte en hierba mojada. La reduccion
las personas. Evitar descargar material en la traccion de la pisada puede causar
contra paredes o barreras. El material puede resbalones.
retornar al operador. Para la cuchilla cuando
se pasa por superficies de grava. III. NINOS
• No opere la segadora sin los respectivos
Se pueden producir accidentes tragicos si el
resguardos, las placas, el recogedor de
operador no presta atenci6n a la presencia
cesped u otros aditamentos dise ados para
de los ni5os. A menudo, los ni5os se sienten
su proteccion y seguridad.
• Refi@ase a las instrucciones del fabricante atraidos por la maquina y por la actividad de
la siega. Nunca suponga que los niSos van a
para el funcionamiento e instalacion de
accesorios. Use Qnicamente accesorios permanecer en el mismo lugar donde los vio
por Qltima vez.
aprobados por el fabricante.
• Mantenga a los ni5os alejados del area de
• Detenga la cuchilla o las cuchillas cuando
la siega y bajo el cuidado estricto de otra
cruce por calzadas, calles o caminos de persona adulta responsable.
grava. • Este alerta y apague la maquina si hay niSos
• Parar el motor cada vez que se abandona el
que entran al area.
aparato, antes de limpiar la segadora o de
remover residuos del tubo. • Antes y cuando este retrocediendo, mire
hacia atras y hacia abajo para verificar si hay
• Apagar el motor y esperar hasta que las
niSos peque5os.
cuchillas esten completamente paradas
• Nunca permita que los ni5os operen la ma-
antes de remover el receptor de hierba.
quina.
• Segar solamente con luz del dia o con una • Tenga un cuidado extra cuando se acerque
buena luz artificial.
a esquinas donde no hay visibilidad, a los
• No opere la maquina bajo la influencia del
arbustos, _lrboles u otros objetos que pueden
alcohol o de las drogas. interferir con su linea de vision.
• Nunca opere la maquina cuando la hierba
este mojada. AsegQrese siempre de tener
buena tracci6n en sus pies; mantenga el IV. MANEJO SEGURO DE GASOLINA
mango firmemente y camine; nunca corra. Usar mucha atenci6n cuando se maneja gaso-
• Desconectar el mecanismo de propulsion lina. La gasolina es extremamente inflamable y
aut6noma o el embrague de transmision en los vapores son explosivos.
las segadoras que Io tienen antes de poner • Apagar todos los cigarrillos, cigarros, pipas y
en marcha el motor. otras fuentes de ignicion.
• Si el equipo empezara a vibrar de una • Usar solo un contenedor apropiado.
manera anormal, pare el motor y revise de • Nunca quitar el tap6n de la gasolina o a_adir
inmediato para averiguar la causa. General- carburante con el motor en marcha. Esperar
mente la vibracion suele indicar que existe que el motor se enfrie antes de repostar la
alguna averia. gasolina.
22
• Nunca repostar la maquina al interior de un • Mantenga las tuercas y los pernos, espe-
local. cialmente los pernos del accesorio de la
• Nunca guardar la maquina o el contenedor cuchilla, apretados y mantenga el equipo en
de gasolina donde hay una llama abierta, buenas condiciones.
chispa o luz piloto como una caldera u otros • Nunca manipule de forma indebida los
dispositivos. dispositivos de seguridad. Controle regular-
• Nunca Ilenar contenedores en un vehiculo, mente su funcionamiento correcto.
en un cami6n o caravana con un forro de • Mantenga la maquina libre de hierba, hojas
plastico. Colocar siempre los contenedores u otras acumulaciones de desperdicio.
en el suelo lejos de su vehiculo antes de Limpie los derrames de aceite o combustible.
Ilenar. Permita que la maquina se enfrie antes de
• Quitar equipos que funcionan con gasolina almacenarla.
del camion o caravana y repostar en el suelo. • Pare e inspeccione el equipo si le pega a un
Si esto no es posible, repostar dicho equipo objeto. Reparelo, si es necesario, antes de
con un contenedor portatil, mas bien que con hacerlo arrancar.
una tobera de gasolina. • En ningQn caso hay que regular la altura de
• Mantener la tobera en contacto con el bordo las ruedas mientras el motor esta en marcha.
del deposito de carburante o de la apertura • Los componentes del receptor de la hierba
del contenedor siempre hasta terminar el van sujetos a desgaste, daSos y deterioro,
abastecimiento. No usar un dispositivo de que pueden exponer las partes en mov-
cierre-apertura de la tobera. imiento o permitir que objetos sean dispara-
• Si el carburante cae en la ropa que se Ileva, dos. Controlar frecuentemente y cuando sea
cambiarsela inmediatamente. necesario sustituir con partes aconsejadas
• Nunca Ilenar en exceso el dep6sito de por el fabricante.
carburante. Colocar el tap6n de la gasolina y • Las cuchillas de la segadora estan afiladas
apretar de modo seguro. y pueden cortar. Cubrir las hojas o Ilevar
guantes, y utilizar precauciones especiales
V. SERVICIO cuando se efectQa mantenimiento sobre las
mismas.
• Nunca haga funcionar una maquina dentro
de un area cerrada. • No cambie el ajuste del regulador del motor
ni exceda su velocidad.
• Nunca haga ajustes o reparaciones mientras
el motor este en marcha. Desconecte el • Mantener o sustituir las etiquetas de
cable de la bujia, y mantengalo a cierta seguridad e instrucciones, cuando sea
necesario.
distancia de esta para prevenir un arranque
accidental.
Numero de Serie:
Fecha de Compra:
Capacidad y Tipo de Gasolina: 1.6 Cuartos (Regular sin Plomo)
Tipo de Aceite (API SG-SL): SAE 30 (Sobre 32°F); SAE 5W-30 (Debajo 32°F)
Capacidad de Aceite: 20 Onzas
Bujia (Abertura: .030") Champion RJ19HX
Torsi6n del Perno de la Cuchilla: 35-40 ft. Ibs.
El nOmero del nodelo y el de serie se encuentran en la calcomania adjunta a la parte trasera
de la caja de la segadora. Debe registrar tanto el nOmero de serie come la fecha de compra y
mantengalos en un lugar seguro para refencia en el futuro.
23
Acuerdos de Protecci6n para la Reparaci6n
Congratulaciones por su buena compra. Su • Ayuda r&pida por telefono - soporte tele-
nuevo producto Craftsman@ esta diseSado fonico por parte de un representante Sears
y fabricado para funcionar de modo fiable por sobre productos que requieren un arreglo en
muchos aSos. Pero como todos los productos, casa, y ademas una programacion sobre los
puede necesitar alguna reparaci6n de tanto a reglos mas convenientes.
en tanto. En este caso tener un Acuerdo de Cuando se ha comprado el Acuerdo, basta con
Proteccion para la Reparacion puede hacerles una Ilamada telefonica para programar el servi-
ahorrar dinero y fastidios. cio. Puede Ilamar cuando quiera, dia y noche o
fijar en linea una cita para obtener el servicio.
Compre ahora un Acuerdo de Protecci6n para Sears tiene mas de 12.000 especialistas
la Reparaci6n y protegese de molestias y gas- profesionales en la reparacion, que tienen
tos inesperados. acceso a mas de 4.5 millones de partes y
accesorios de calidad. Este es el tipo de
Un Acuerdo incluye los puntos siguientes: profesionalidad con que puede contar para
• Servicio experto de nuestros 12.000 espe- ayudar a alargar la vida del producto que acaba
cialistas profesionales en la reparacion. de comprar, por muchos a5os. iCompre hoy su
• Servicio ilimitado sin cargo alguno para Acuerdo de Protecci6n para la Reparaci6n!
las partes y la mano de obra sobre todas las Se aplican algunas limitaciones y exclu-
reparaciones garantizadas. siones. Para conocer los precios y tener
• Sustitucion del producto si su producto m&s informacion, Ilame al 1-800-827-6655.
garantizado no puede ser arreglado. Servicio de Instalacion Sears
• Descuento del 10% sobre el precio cor- Para la instalaci6n profesional Sears de
riente del servicio y de las partes relativas al aparatos de casa, puertas de garaje,
servicio no cubiertas por el acuerdo; tambien calentadores de agua y otros importantes
el 10% menos sobre el precio corriente de articulos para la casa, en U.S.A. Ilamar a
un control de mantenimiento preventivo. 1-800-4-MY-HOME®.
Estos accesorios estaban disponibles cuando se produjo la segadora. No son facilitados junto al
cortacesped Tambien estan disponibles en la mayoria de las tiendas de Sears y en los centros
de servicio. AIgunos de estos accesorios tal vez no se apliquen a su segadora.
RENDIMIENTO DE LA SEGADORA
DESVIADOR
DE RECORTES
ESTABILI- ENVASES
PARASEGADORAS
ZADORES
CON DESCARGA
TRASERA E GASOLINA
LATERAL
CON TRASERA
DESCARGA ?1 CONDESCARGA
MANTENIMIENTO DE LA SEGADORA
ADAPTADORES ACEITE
CORREAS CUCHILLAS DE CUCHILLA RUEDAS DEL MOTOR
24
Lea estas instrucciones y este manual comple- COMO PREPARAR SU SEGADORA
tamente antes de tratar de montar u operar su PARA DESDOBLAR EL MANGO
segadora nueva. IMPORTANTE: Despliegue el mango con
IMPORTANTE: Este cortacesped viene SIN mucho cuidado para no pellizcar o daSar los
ACEITE O GASOLtNA en el motor. cables de control.
Su segadora nueva ha sido montada en la 1. Levante los mangos hasta que la secci6n
fabrica con la excepci6n de aquellas partes que del mango inferior se asegure en su lugar,
se dejaron sin montar por razones de envio. en la posici6n para segar.
Todas las partes como las tuercas, las arande- 2. Remueva la cuba protectora, levante la sec-
las, los pernos, etc., que son necesarias para ci6n del mango superior hasta su lugar en
completar el montaje han sido colocadas en la el mango inferior, y apriete ambas manillas
bolsa de partes. Para asegurarse que su sega- del mango.
dora funcione en forma segura y adecuada, 3. Remueva la cuba del mango que sujeta la
todas las partes y los articulos de ferreteda que barra de los control que exige la presencia
se monten tienen que ser apretados segura- del operador junto con el mango superior.
mente. Use las herramientas correctas, como El mango de la segadora puede ajustarse
sea necesario, para asegurar que se aprieten segQn le acomode para segar. Refierase a
adecuadamente. "AJUSTE DEL MANGO" en la seccion de
Servicio y Ajustes de este manual.
PARA REMOVER LA SEGADORA DE
LA CAJA DE CARTON Barra POSICION
Mango Inferior
25
PARA MONTAR EL RECOGEDOR DE PARA PREPARAR LA BATERJA
CO:SPED AVISO: $u bateria tiene que estar cargada an-
1. Ponga el bastidor del recogedor de cesped tes de que pueda hacer arrancar su segadora.
en la bolsa del cesped con la parte rigida 1. Conecte el conector del cargador de la
de la bolsa en la parte inferior. AsegQrese bateda (macho) al conector de la arnes
que el mango del bastidor este en el exte- (hembra).
rior de la parte superior de la bolsa. 2. Enchufe el cargador de la bateria dentro del
2. Deslice los sujetadores de vinilo sobre el enchufe de 110 volt C.A.
bastidor. 3. Deje el cargador de la bateria conectado
AVlSO: Si los sujetadores de vinilo estan muy por 24 horas antes de hacer arrancar su
duros, metalos en agua caliente por algunos motor por la primera vez.
minutos. Si se moja la bolsa, dejela que se 4. Despues de cargar, desconecte el conec-
seque antes de usarla. tor de la arnes (hembra) al conector de la
cargador de la bateria (macho).
Mango del
bastidor de]
Conecte su cargador de bateda para cargarla
segQn despues decada uso.
recogedor
IMPORTANTE: El motor no cargara una
bated&
AI final de la temporada de siega, la bateda
se debe cargar por 48 horas para protegeda
durante el periodo de almacenamiento en el
invierno.
_PRECAUCl6N: Siempre desconecte el co-
nector del motor del conector de la bateria para
evitar el arranque por accidente al transportar o
guardar su segadora despues de la temporada.
Conector Conector
del motor della arnes
Sujetador_ Abertura
de vinilo del bastidor (macho) (hembra)
'\
\
\
Conector del
cargador (macho)
26
FAMILIARICESE CON SU SEGADORA
LEA ESTE MANUAL DEL DUENO Y LAS REGLAS DE SEGURtDAD ANTES DE OPARAR SU
SEGADORA. Compare las ilustraciones con su segadora para familiarizarse con la ubicacion de
los diversos controles y ajustes. Guarde este manual para referencia en el futuro.
ATTENCION O MOTOR MOTOR R,_PIDO LENTO ESTRANGU COM- ACEITE PELIGRO, GUARDE LAS
ADVERTENCIA ENCENDIDO APAGADO LACION BUSTIBLE MANOS Y LOS PIES LEJOS
Barra de
control de la
Barra de control que exige la
impulsion
presencia del operador
Mango del
arrancador
auxiliar
Cebador
Recogedor
de cest
Silenciador
Filtro de aire
Puerta de la acolchadora
la impulsion
Ajustador de
IMPORTANTE: Este cortacesped viene la rueda (en
SIN ACEtTE O GASOLINA en motor. Caja cada rueda)
Barra de control que exige la presencia del Cebador - bombea combustible adicional
operador - tiene que sujetarse abajo, junto desde el carburador al cilindro para uso cuando
con el mango, para hacer arrancar el motor. se necesita hacer arrancar un motor frio.
Sueltela para parar el motor. Puerta de la acolchadora - permite la conver-
Interruptor de arranque de Ilave - se usa sion para la operacion de descarga o ensacado.
para hacer arrancar el motor. Barra de control de la impulsion - se usa
Mango del arrancador auxiliar - se usa para para enganchar la segadora para movimiento
hacer arrancar el motor.
2_,haciaf adelante impulsada a motor.
Barra de control que exige la presencia del operador
Laoperacion de cualquier
segadorapuedehacerque
saltenobjetosextraSosdentrode
susojos,Ioquepuedeproducir
daSosgravesenestos.Siempre
useanteojosdeseguridad o proteccion
para Barra de
accionamiento
losojosmientrasoperesu segadorao cuando
hagaajusteso reparaciones.
Recomendamos
gafaso unamascara deseguridaddevisi6n CONTROL DELA
ampliade seguridadusadasobrelasgafas. IMPULSION
DESENGANCHADO
COMOUSAR SU SEGADORA
VELOCIDAD DEL MOTOR
La velocidad del motor se establecio en la fa-
PARA AJUSTAR
brica para un rendimiento optimo. La velocidad MUEVA HACIA EL
no se puede ajustar. PROXIMO AGUJERO
.... i- _
PALAN2 p,aca
HACIA
ADELANTE PARA LEVANTAR EL CORTAC¢:SPED
28
PARA CONVERTIR LA SEGADORA \
/
Mango del
bastidordel
recogedor
Abra la protecci6n -'_ cesped
contra la descarga
Desviador
de la descarga
29
ANTES DE HACER ARRANCAR EL _PRECAUCl6N: Limpie el aceite o el
MOTOR combustible derramado. No almacene, derrame
AGREGUE ACEITE o use gasolina cerca de una llama expuesta.
Su segadora fue enviada sin aceite en el motor. _IPRECAUCl6N: Los combustibles
Para el tipo y el grado del aceite a utiNzar, vea mezclados con alcohol (conocidos como
el "MOTOR" en la seccion del Mantenimiento
gasohol, o el uso de etanol o metanol) pueden
de este manual.
atraer la humedad, la que conduce a la
_PRECAUCl6N: NO sobreNene el motor con
separacion y formacion de acidos durante el
aceite, o fumara pesa demante del silenciador almacenamiento. La gasolina acidica puede
cuando Io vaNa a arrancar. daSar el sistema del combustible de un motor
1. AsegQrese que la segadora este nivelada. durante el almacenamiento. Para evitar los
2. Remueva la varila medidora de aceite del problemas con el motor, se debe vaciar el
tubo de desarga de aceite. sistema del combustible antes de guardarlo
3. Usted recibe un envase de aceite con la
por un periodo de 30 dias o mas. Vacie el
unidad. Vierta lentamente el envase entero
de aceite en el tubo de relleno del motor. estanque del combustible, haga arrancar el
motor y hagalo funcionar hasta que las lineas
AVlSO: El terraplen inicial del aceite requiere
solamente 18 onzas debido al aceite residual del combustible y el carburador queden vacios.
en el motor de la prueba de calidad de 100% La pr6xima temporada use combustible nuevo.
del fabricante. AI cambiar el aceite puede Vea las lnstrucciones Para El AImacenamiento
necesitar 20 onzas. para mas informacion. Nunca use productos de
4. Inserte y apriete la variNa medidora de limpieza para el motor o para el carburador en
aceite. el estanque del combustible pues se pueden
IMPORTANTE: producir da5os permanentes.
• Revise el nivel del aceite antes de cada uso.
Agregue aceite si es necesario. Llene hasta
la linea de Ileno en la varilla medidora de PARA PARAR EL MOTOR
nivel. • Para parar el motor, suelte la barra de con-
• Cambie el aceite despues de 25 horas de troles que exigen la presencia del operador.
operacion o una vez por temporada. Puede
necesitar cambiar el aceite mas a menudo PARA HACER ARRANCAR EL MOTOR
cuando las condiciones son polvorosas o su- AVISO: Debido alas capas protectoras del mo-
cias. Vea "PARA CAMBIAR EL ACEtTE DEL tor, una cantidad peque_a de humo puede es-
MOTOR" en la seccion de Mantenimiento de tar presente durante el uso inicial del producto
este manual. y se debe considerar normal.
1. Para hacer arrancar un motor frio, empuje
el cebador tres (3) veces antes de tratarlo.
Lpa del
deposito de
Empuje firmemente. Este paso normal-
aceite
mente no es necesario cuando se hace
arrancar un motor que ya ha estado funcio-
nando por unos cuantos minutos.
2. Sujete la barra de control que exige la
presencia del operador abajo en el mango y
gire la Nave para el arranque electrico en el
sentido de las manillas del reloj para hacer
arrancar el motor.
Tapa del IMPORTANTE: No haga arrancar el motor
rellenador
mas de 5 segundos continuados. Espere 5 a 10
de
segundos entre cada vez que trate de hacerlo
gasolina
arrancar.
• Para comenzar el motor sandio el arrancador
de soga, siga los pasos de arriba. Cambie el
uso del Nave de arranque con el arrancador
AGREGUE GASOLINA de soga. No permita que la soga vuelva a su
• Llene el estanque de combustible hasta la posicion inicial demasiado brusca mente.
parte inferior del cuello de relleno del es- AVlSO: En climas mas frios puede que sea
tanque de gasolina. No Io Ilene demasiado. necesario repetir los pasos del cebado. En cli-
Use gasolina regular, sin plomo, nueva y lim- mas mas calurosos el cebar demasiado puede
pia con el minimo de 87 octanos. No mezcle producir el ahogo y el motor no va a arrancar.
el aceite con la gasolina. Para asegurar Si se ahoga el motor espere unos cuantos
que la gasolina utilizada sea fresca compre minutos antes de tratar de hacerlo arrancar y
estanques los cuales puedan ser utilizados no repita los pasos del cebado.
durante los primeros 30 dias.
30
ONSEJOS PARA SEGAR CONSEJOS PARA SEGAR Y ACOL-
PRECAUCION: No utilizar dispositivos anti- CHAR
paja de la hoja en la segadora ya que estos IMPORTANTE: Para obtener el mejor
accesorios son peligrosos, pueden daSar su rendimiento mantenga la caja de la segadora
segadora y anular su garantla. sin acumulacion de cesped y basura. Vea
• Bajo ciertas condiciones, tal como cesped "LIMPtEZA" en la seccion de Mantenimento de
muy alto, puede ser necesario el elevar este manual.
la altura del corte para reducir el esfuerzo
• La cuchilla acolchadora especial va a volver
necesario para empujar la segadora y para
evitar sobrecargar el motor, dejando mon- a cortar los recortes de cesped muchas
tones de recortes de cesped. Puede que sea veces, y los reduce en tamaSo, de modo que
necesario reducir la velocidad del recorrido si se caen en el cesped se van a dispesar
y/o haga funcionar la segadora sobre el area entre este y no se van a notar. Tambien, el
cesped acolchado se va a deshacer rapi-
por segunda vez.
• Para un corte muy pesado, reduzca el ancho damente entregando substancias nutritivas
del corte pasando parcialmente por encima para el cesped. Siempre acolche con la
velocidad del motor (cuchilla) mas alta, pues
del lugar anteriormente cortado y siegue
lentamente. asf se obtendra la mejor accion de recorte de
las cuchillas.
• Para un mejor ensacado del cesped y para la
• Evite cortar el cesped cuando este mojado.
mayorfa de las condiciones de corte, la velo-
cidad del motor debe ajustarse a la posicion El cesped mojado tiende a formar montones
de RAPIDO. e interfiere con la accion de acolchado.
• Los poros en los recogedores de cesped de La mejor hora para segar el cesped es
tela pueden Ilenarse con mugre y polvo con temprano en la tarde. A esa hora este se ha
secado y el area recien cortada no quedara
el uso y los recogedores recaudaran menos
cesped. Para evitar este, rocle el recogedor expuesta al sol directo.
• Para obtener los mejores resultados, ajuste
con la manguera de agua regularmente y
la altura del corte de la segadora de modo
dejelo secarse antes de usarlo.
• Mantenga la parte superior del motor, aired- que esta corte solamente el tercio superior
de las hojas de cesped. En el caso de que el
edor del arrancador, despejada y sin recortes
de cesped y paja. Esto ayudara el flujo del cesped haya crecido demasiado, puede ser
aire del motor y extendera su duracion. necesario el elevar la altura del corte para
reducir el esfuerzo necesario para empujar la
segadora y para evitar sobrecargar el motor,
dejando montones de recortes de cesped.
Para un cesped muy pesado, reduzca el an-
cho del corte pasando por encima del lugar
anteriormente cortado y siegue lentamente.
1/3
31
PROGRAMA DE ANTEsDESPUES
DECADA
DECADAcADA2S,ORASO100
CADA CADAANTESDEL
ALMACE-
MANTENIMIENTO uso uso .ORASTEMPORADA.ORAS.AMIENTO
Revisar si hay Sujetadores Sue_tos
S Limpiar/Inspeccionar el Recogedor de C_sped *
A Lubricaci6n
(_ Rocie el lubricante
ANTES DE CADA USO
• Revise el nivel del aceite del motor. (_) Vea "MOTOR" en la seccion de Mantenimiento
• Revise si hay sujetadores sueltos.
IMPORTANTE: No aceite o engrase los roda-
LUBRICACION mientos de la rueda de plastico. Los lubricantes
Mantenga la unidad bien lubricada viscosos atearan polvo y mugre, Io acortara la
(vea la "TABLA DE LUBRtCACION"). duracion de los rodamientos autolubricantes. Si
cree que tienen que lubricarse, use Iosamente
un lubricante tipo crafito, de polvo seco, en
forma moderada.
32
SEGADORA PARA CAMBIAR LA CUCHILLA
Siempre observe las reglas de seguridad cu- 1. Ponga el adaptador de la cuchilla en el
ando haga el mantenimiento. ciguefial del motor. AsegQrese que la ranura
LLANTAS del adaptador y que el chavetero del cigue-
fial esten alineados.
• Mantenga las Ilantas sin gasolina, aceite o
substancias quimicas para control de insec- 2. Ponga la cuchilla en el adaptador de esta
tos que pueden dafiar la goma. alineando los dos (2) agujeros en la cuchilla
con las salientes elevadas en el adaptador.
• Evite los tocones, las piedras, las grietas pro-
3. AsegQrese de que el borde de salida de
fundas, los objetos afilados y otros peligros la cuchilla (opuesto al borde afilado) este
que pueden dafiar a las Ilantas. hacia arriba hacia el motor.
RUEDAS DE IMPULSION 4. Instale el perno de la cuchilla con la aran-
Revise las ruedas de impulsi6n delanteras cada dela de seguridad y la arandela endurecida
vez antes de segar, para asegurarse de que se en el adaptador de la cuchilla y el ciguefial.
mueven libremente. Si las ruedas no giran li- 5. Use un bloque de madera entre la cuchilla
bremente quiere decir que hay basura, recortes y la caja de la segadora y apriete el perno
de cesped, etc. en el area de las ruedas de de la cuchilla girandolo en el sentido en que
impulsion y tienen que limpiarse para liberarlas. giran las manillas del reloj.
Es necesario limpiar las ruedas de impulsion; • La torsi6n para apretar recomendada es de
revise ambas ruedas delanteras. 35 - 40 pies libras.
1. Remueva los tapacubos, las tuercas de
Adaptador de Ranura Chavetero del
seguridad y las arandelas.
la cuchilla " uenal
2. Remueva las ruedas de los ajustadores de
las ruedas. Arandela de
3. Remueva la basura y los recortes de seguridad
cesped de dentro de la cubierta contra
el polvo, pifi6n y/o de los dientes de los
engranajes de las ruedas de impulsi6n.
4. Ponga las ruedas de vuelta en su lugar.
AVlSO: Si despues de limpiar las ruedas de
impulsion no giran libremente, p6ngase en Perno Arandela
contacto con su centro de servicio Sears o con de la endurecida
un otro centro de servicio cualificado. cuchilla Borde de salida" iguenal
CUIDADO DE LA CUCHILLA
Para obtener los mejores resultados, la cuchilla IMPORTANTE: El perno de la cuchilla es
de la segadora tienen que mantenerse afilada. tratado a calo. Si es necesario sustituir los
Cambie la cuchilla doblada o dafiada. pernos, sustituirlos s61o con pernos aprobados
_PRECAUCl6N: Usar solamente la hoja mostrados en la seccion Partes de Reparacion
de repuesto aprobada por el fabricante de su de este manual.
cortacesped. Usar una hoja no aprobada por el PARA AFILAR LA CUCHILLA
fabricante de su cortacesped es peligroso, pu- AVlSO: No recomendamos el afilar la cuchilla
ede dafiar su cortacesped y anular su garantia. - pero si Io hace, asegQrese de que quede
PARA REMOVER LA CUCHILLA balanceada. Se tiene que tener cuidado de
1. Desconecte el alambre de la bujia y p6n- mantenerla balanceada. Una cuchilla que no
galo en donde no pueda entrar en contacto esta balanceada va a producir eventualmente
con esta. dafio en la segadora o en el motor.
2. Haga descansar la segadora en su lado. • La cuchilla puede afilarse con una lima o en
AsegQrese que el filtro de aire y que el una rueda rectificadora. No trate de afilarla
carburador queden mirando hacia arriba. mientras se encuentra en la segadora.
3. Use un bloque de madera entre la cuchilla • Para revisar el balance de la cuchilla, clave
y la caja de la segadora para evitar que la un clavo en una viga o en la pared. Deje
cuchilla gire cuando se le quite el perno. alrededor de una pulgada de un clavo recto
AVlSO: Proteja sus manos con guantes y/o expuesto. Ponga el agujero central de la
envuelva la cuchilla con una tela gruesa. cuchilla sobre la cabeza del clavo. Si la
4. Remueva el perno de la cuchilla girandolo cuchilla esta balanceada debe permanecer
en el sentido contrario en que giran las en la posicion horizontal. Si cualquiera de
manillas del reloj. los extremos de la cuchilla se mueve hacia
5. Remueva la cuchilla y los articulos de fer- abajo, afile el extremo pesado hasta que esta
reteria adjuntadores (el perno, la arandela quede balanceada.
de seguridad y la arandela endurecida). RECOGEDOR DE CO:SPED
AVIS0: Remueva el adaptador de la cuchilla y • El recogedor de cesped puede ser rociado
revise el cubo interior de la ranura del adap- con el agua de la manguera pero tiene que
tador de la cuchilla. La ranura tiene que estar estar seco cuando se vaya a usar.
en buenas condiciones para que funcione en • Revise su recogedor de cesped a menudo
forma adecuada. Cambie el adaptador siesta para verificar siesta dafiado o deteriorado.
dafiado. Se va a desgastar con el uso normal. Si se
33 necesita cambiar el recogedor, cambielo
solamente por uno que sea aprobado por el 6. Parar de adadir aceite cuando se alcanza la
fabricante. De el nOmero del modelo de la sedal de Ileno (FULL) en la varilla. Esperar un
segadora cuando Io ordene. minuto para dejar que el aceite se arregle.
CAJA DE ENGRANAJES 7. ContinQe agregando cantidades pequeas
• Para mantener el sistema de impulsion de aceite y vuelva a inspeccionar la varilla
funcionando en forma adecuada, la caja de medidora settles del nivel de aciete en Ileno
engranajes y el area alrededor de la impulsion (FULL). NO sobrellene el motor con aceite,
tienen que mantenerse limpias y sin acumu- o fumara pesa demante del silenciador
lacion de basura. Limpie debajo de la cubierta cuando Io valla a arrancar.
de la impulsion dos veces por temporada. 8. AsegQrese de apretar la varilla medidora
• La caja de engranajes se Ilena con lubricante del aceite antes de arrancar el motor.
hasta el nivel adecuado en la fabrica. La 9. Vuelva a conectarel alambre de la bujia a esta.
Onica vez que el lubricante necesita atencion
es cuando se le ha prestado servicio a la
caja de engranajes.
• Si se necesita lubricante, use solamente
Grasa Texaco Starplex Premium 1, Parte No.
750369. No use substitutos.
MOTOR
LUBRICAClON
Use solamente aceite de detergente de alta cali- FILTRO DE AIRE
dad clasificado con la clasificacion SG-SL de ser-
vicio API. Seleccione la calidad de viscosidad SAE Su motor puede sufrir averias y funcionar de
manera incorrecta con un filtro del aire sucio.
segQn su temperatura de operacion esperada.
Sustituir el papel del cartucho una vez al ado
o tras 100 horas de funcionamiento, mas a
menudo si se utiliza en condiciones de sucie-
dad y polvo particulares.
PARA LIMPIAR EL FILTRO DE AIRE
1. Suelte el tornillo e incline la cubierta para
removerlo.
AVlSO: A pesar de que los aceites de multi- 2. Cuidadosamente, remueva el cartucho.
viscosidad (5W30, 10W30, etc.) mejoran el 3. Limpielo golpeandolo suavemente en una
arranque en clima frio, estos aceites de mul- superficie plan& Siesta muy sucio cambie
tiviscosidad van ha aumentar el consumo de el cartucho.
aceite cuando se usan en temperaturas sobre _,PRECAUCl6N: Los solventes de petr61eo,
32 ° E Revise el nivel del aceite del motor mas a tales como el keroseno, no se deben usar para
menudo, para evitar un posible dado en el mo- limpiar el cartucho. Pueden producir el deterioro
tor, debido a que no tiene suficiente aceite. de este. No aceite el cartucho. No use aire a
Cambie el aceite despues de 25 horas de presi6n para limpiarlo o secarlo.
operacion o por Io menos una vez al ado si la 4. Instale el cartucho, luego vuelva a poner la
segadora se utiliza menos 25 horas el ado. cubierta asegurandose que las orejas esten
Revise el nivel del aceite del carter antes de alineadas con las ranuras en la plancha
arrancar el motor y despues de cada cinco (5) trasera. Apriete el tornillo en forma segura.
horas de uso continuado. Apriete el tap6n del
Labio | _ Plancha
aceite en forma segura cada vez que revise el
nivel del aceite. i( ! "_ trasera
PARA CAMBIAR EL ACEITE DEL MOTOR
AVlSO: Antes de inclinar la segadora para drenar
el aceite, drene el tanque de combustible hacien- _ ',,iJ
do correr el motor hasta que el tanque este vacio.
1. Desconecte el alambre de la bujia y
p6ngalo de modo que no pueda entrar en
contacto con esta. Cartucho _ Ranuras
2. Remueva la tapa del dep6sito del aceite;
L_._ _......_ "Orejas de
dejela a un lado en una superficie limpia.
"Cubierta la cubierta
3. Incline la cortadora de cesped por este
costado tal como se muestra y purgue el SILENClADOR
aceite en un recipiente id6neo. Mueva la Inspeccione y cambie el silenciador siesta corroi-
segadora de atras para adelante para re- do puede producir un peligro de incendio y/o dado.
mover todo el aceite que se haya quedado BUJiA
atrapado dentro del motor. Cambie el bujia al comienzo de cada tempo-
4. Limpie todo el aceite derramado en la sega- rada de siega o despues de cada 100 horas
dora yen el lado del motor. de operacion, Io que suceda primero. El tipo de
5. Echar aceite despacio en el conducto del bujia y el ajuste de la abertura aparecen en "ES-
aceite, parandose a intervalos regulares para PECIFICACIONES DEL PRODUCTO" seccion
controlar el nivel del aceite con la varilla.
34de este manual.
LIMPIEZA • Mantenga lassuperficies pulidasy lasrue-
IMPORTANTE: Paraobtenerelmejorrendimineto, dassingasolina, aceite,etc.
mantenga lacajadelasegadora sinacumulacion • Norecomendamos el usodeunamanguera
decespedy basura.Limpiela partedeabajode dejardinparalimpiarlasegadoraa menos
su segadora despuesdecadauso. queelsistemaelectrico,el silenciador, el
_PRECAUCl6N: Desconecte elalambrede filtrodeairey el carburador estentapados
paraevitarquelesentreelagua.Elaguaen
labujiay p6ngaloen dondenopuedaentraren el motorpuedeacortarladuraci6ndeeste.
contactoconesta. LIMPIEDEBAJODELACUBIERTA DELA
• Hagadescansarla segadoraen su lado. IMPULSION
AsegQrese queel filtrodeairey queel carbu- Limpiedebajodela cubiertadela impulsionpor
radorquedenmirandohaciaarriba.Limpiela Iomenosdosvecescadatemporada. Raspede-
parteinferiordesusegadora raspandolapara bajode la cubiertaconuncuchilloparamasilla
removerla acumulaci6n decespedy basura. o conunaherramienta parecida,pararemover
• Limpieel motora menudoparaevitarque todaacumulaci6n decespedo basuraen la parte
seacumulelabasura.Unmotortapadofun- inferior de la cubierta de la impulsion.
cionamascalientey seacortasuduraci6n.
Estribo
de la correa
Defensa en
contra del desperdicio
35
PARA AJUSTAR EL MANGO
El mango puede ser montado a una posici6n
alta o baja. Los agujeros de montaje en el
mango inferior estan fuera del centro para
levantar y bajar el mango.
1. Remueva el mango superior y conexi6ne(s)
el asegurar el (los) cable(s) al mango infe-
rior.
2. Remueva el panel de mango del mango
inferior. \
GIRAR
MOTOR
VELOCIDAD DEL MOTOR
La velocidad del motor ha sido ajustada en
la fabrica. No trate de aumentar la velocidad
. Remueva las clavijas de horquilla de la
del motor pues se pueden producir lesiones
clavija de montaje del puntal del mango.
personales. Si cree que el motor esta funcio-
Posici6n nando demasiado rapido o demasiado lento,
pa Ileve su segadora a mas con su centro de
servicio Sears o con un otro centro de servicio
cualificado.
CARBURADOR
Su carburador tiene un chorro principal fijo
Clavija no ajustable para controlar la mezcla. Si su
de horquilla motor no esta funcionando en forma adecuada
Clavija de debido a problemas que se sospecha vienen
montaj del carburador, Ileve su segadora a contacto
POSICION BAJA POSICION ALTA con su centro de servicio Sears o con un otro
centro de servicio cualificado para repararla y/o
4. Apreite el mango inferior hacia dentro para ajustarla.
removerlo de las clavijas de montaje. IMPORTANTE: Nunca manipule el regulador
5. Gire el mango inferior por encima para del motor, el que ha sido ajustado en la fabrica
levantar o bajar el mango. para la velocidad del motor adecuada. Puede
6. Apreite el mango inferior hacia dentro y ser peligroso hacer funcionar el motor a una
posicione los agujeros por encima de las velocidad por sobre el ajuste de alta velocidad
clavijas de montaje que se encuentran de la fabrica. Si cree que la velocidad alta
sobre el puntal del mango. regulada del motor necesita ajuste,contacto con
7. Vuelva a montar el panel de mango al su centro de servicio Sears o con un otro centro
mango inferior. de servicio cualificado, el que cuenta con el
8. Vuelva a montar el mango superior y todas equipo adecuado y la experiencia para hacer
las partes removidas del mango inferior. los ajustes necesarios.
37
SOLUCION DE PROBLEMAS - Vea la secci6n apropiada en el manual amenos que
estd dirigido a un centro de servico Sears.
PROBLEMA CAUSA CORRECCION
38
SOLUCION DE PROBLEMAS - Vea la secci6n apropiada en el manual amenos que
est_ dirigido a un centro de servico Sears.
PROBLEMA CAUSA CORRECCION
39
CRAFTSMAN ROTARY LAWN MOWER- - MODEL NUMBER 917.37674:2
8
27
25
59
37
19
52
55
26 14
O 9
\
39
44
48
17
11
56
I
15 60 40 42
35
34
51
32
29
28
CRAFTSMAN ROTARY LAWN MOWER- - MODEL NUMBER 917.376742
1 194200X479 Upper Handle 29 401630 Washer, Curved, Cylindrical 52 404763 Danger Decal
2 189686 Key Start Switch 30 401180X004 Axle Arm Assembly 53 17600406 Screw, Serrated, TT 1/4-20
(Includes Key) 31 701037 Selector Knob 54 88348 Washer, Flat
3 850733X004 Bracket, Upstop 32 401626X004 Selector Spring 55 751592 Nut, Hex 3/8-16
4 166649 Mulcher Plug 33 189917X428 Mulcher Door 56 88652 Hinge Screw 1/4-20 x 1-1/4
5 66426 Wire Tie 34 401629 Spacer 57 51793 Hairpin Cotter
6 189713X428 Handle Knob 35 700325X005 Wheel Adjusting Bracket 58 400512X479 Lower Handle
7 750634 Screw 36 175735 Hinge Bracket Assembly 59 191574 Handle Bolt
8 194199X428 Control Bar 37 150078 Screw, Sems, Thread Cutting 60 74760612 Bolt, Hex Head 3/8-16 x 3/4
9 401813X428 Rear Door Assembly 5/16-18 x 3/4 62 405842 Debris Shield
10 128415 Pop Rivet 38 402574X428 Discharge Deflector 63 192325 Screw, Debris Shield
11 150050 Screw, Self-Tapping 39 195915X479 Handle Bracket Assembly, LH 64 -- - Engine, Briggs & Stratton,
#10-24 x 5/8 40 195914X479 Handle Bracket Assembly, RH Model Number 124T05-
4_12 54583 Screw, Hex Hex Head, 41 150406 Screw, Hex Head, Threaded, 3848-B2 (See Breakdown)
Sems 1/4-20 x 1/2 Rolled 3/8-16 x 1-1/8 65 197480 O-Ring
14 195622X479 Back Plate 42 193000 Spring, Torsion 69 197991 Clip, Cable
15 410545X479 Side Baffle 43 73800400 Nut, Hex, Nylock 71 188839X004 Mounting Bracket,
16 176655X479 Discharge Baffle 44 414523 Kit, Mower Housing (Includes Debris Shield
17 140661X479 Rear Baffle Key Numbers 14, 15 and 51) 75 186159 Screw
18 132004 Keps Locknut 1/4-20 45 175650 Rod, Hinge 76 180331 Key
19 194788 Rope Guide 46 194037 Blade Adapter / Pulley -- 404764 Warning Decal (not shown)
2O 189008 Rear Skirt 47 406707 Blade, 22" -- 413696 Owner's Manual
21 405421 Spring, Rear Door, LH 48 851074 Washer, Hardened Available accessories not included with mower:
24 405423 Spring, Rear Door, RH 49 850263 Washer, Helical -- 71 33623 Gas Can
25 409149 Nut, Hex, Flanged 50 851084 Screw, Machine, Hex Head (2.5 Gallon Container)
26 184193 Bolt, Rear Door 3/8-24 x 1-3/8 Grade 8 -- 71 33500 Fuel Stabilizer
27 407773X427 Wheel & Tire Assembly, Rear 51 170031 Kit, Front Baffle -- 71 33000 SAE 30W Oil
28 142748 Bolt, Shoulder 3/8-16 x 1 (Includes Key Number 53) (20 Ounce Bottle)
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm.
IMPORTANT: Use only Original Equipment Manufacturer (O.EM.) replacement parts. Failure to do so could be hazardous, damage your lawn mower and void your warranty.
CRAFTSMAN ROTARY LAWN MOWER- - MODEL NUMBER 917.37674:2
"_, 31 56 / 37
\ /./"
4
28
44 _
\ 45
11
12
\ 13
\ 14
\ 2
4_ \\
I"0
\
\
\ \
\ \
14
15
13
12
36
1t
CRAFTSMAN ROTARY LAWN MOWER- - MODEL NUMBER 917.376742
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm.
IMPORTANT: Use only Original Equipment Manufacturer (O.EM.) replacement parts. Failure to do so could be hazardous, damage your lawn mower and void your warranty.
BRIGGS & STRATTON 4-CYCLE ENGINE MODEL NUMBER 124T05-3848-B2
684
287
_
524
635
718
5
868 40_,4_
lO_
35 _ _ 45
306
307_
44
BRIGGS & STRATTON 4-CYCLE ENGINE MODEL NUMBER 124T05-3848-B2
425
968
445 443_
3001
613 971
137
276_
127_ 130
1
121 CARBURETOR OVERHAUL KIT 617
45
BRIGGS & STRATTON 4-CYCLE ENGINE MODEL NUMBER 124T05-3848-B2
9211969 ]
604
332 @
304
305
_670
190_ 65
9721 592
58
60
689 0
456 @
601 597 _
46
BRIGGS & STRATTON 4-CYCLE ENGINE MODEL NUMBER 124T05-3848-B2
3© 20 524<> 668
617_ 51_
48
562_
334_
615 @
404
510 1 742 _
937
783A O
1160_ 745
80,
231 _
621
544
697
803
3101
802
47
BRIGGS & STRATTON 4-CYCLE ENGINE MODEL NUMBER 124T05-3848-B2
48
BRIGGS & STRATTON 4-CYCLE ENGINE MODEL NUMBER 124T05-3848-B2
49
SERVICE NOTES
5O
SERVICE NOTES
51
Your Home
iiiiiiiiiiiiiiiiiiiii_i
_
iiiiiiiiiiiiiiiiiiii_ For repair - in your home - of all major brand appliances,
lawn and garden equipment, or heating and cooling systems,
no matter who made it, no matter who sold it!
For the replacement parts, accessories and
owner's manuals that you need to do-it-yourself.
For Sears professional installation of home appliances
and items like garage door openers and water heaters.
I-800o4°MYoHOME ® Anytime, day or night
(1=800-469-4663) (U,S.A. and Canada)
www.sears.com www.sears.ca
Our Home
For repair of carry-in products like vacuums, lawn equipment,
and electronics, call or go on-line for the nearest
Sears Parts and Repair Center.
iiiiiiiiiiiiiiiii
iiiiiiiiiiiiiiiii 1-800-488-t222 Anytime, day or night (U,S,A, only)
iiiiiiiiiiiiiiiii www.sears.com
iiiiiiiiiiiiiiiii
iiiiiiiiiiiiiiiii
iiiiiiiiiiiiiiiii To purchase a protection agreement (U.S.A.)
iiiiiiiiiiiiiiiii
or maintenance agreement (Canada) on a product serviced by Sears:
iiiiiiiiiiiiiiiii t-800-827-6655 (U.S.A.) t-800-361-6665 (Canada)
iiiiiiiiiiiiiiiii
iiiiiiiiiiiiiiiii
iiiiiiiiiiiiiiiii
Para pedir servicio de reparaci6n Au Canada pour service en frangais:
iiiiiiiiiiiiiiiii
a domidlio, y para ordenar piezas: 1-800-LE-FOYER Mc
Io888..SU-HOGAR ® (1-800-533-6937)
www,s@ars,ca
(1-88&784_27)