Beruflich Dokumente
Kultur Dokumente
MY PROFILE
REPORTS
BUY PACKAGE
Solution Report For Full Syllabus Test5 : Basic Level :
Practice Test13
NEWS Represent whole test solution with correct and incorrect answers.
View Your Test Analysis
Ask an Expert
Q. Question Status
No
Q.1
If the product of two integers 53 and 22 in a specific number system is
1276, then what is the decimal equivalent of the number 4371 in the
same number system?
a. 3323
b. 3223
c. 3232
d. 3213
Not Attempt Correct Ans. b
FAQ? Have any doubt? Solution
Q.2
Choose the pair of words to be placed in the 2 blanks in the given
sentence so that the completed sentence becomes meaningful.
After having been close friends for more than a decade, they had a
_____ last year and have not _____each other ever since.
a. fight, talked
b. argument, met
c. dispute, seen
d. quarrel, admired
Not Attempt Correct Ans. c
FAQ? Have any doubt? Solution
http://s3.onlinetestseriesmadeeasy.in/madeeasy/index.php?pageName=timeManagementReport&testid=598&t=a&testType=2 1/20
2/5/2016 MADE EASY ONLINE TEST SERIES
Q.3
In the sentence that follows, two words or phrases have been
highlighted. One of them or both of them or none of them may have an
error. Identify the option containing a pair of words/phrases that will
make the sentence most meaningful.
While the company make great strides on the environment front, it has
updated its HR policies.
a. make, will update
b. making, updating
c. made, did not update
d. No correction required
Not Attempt Correct Ans. c
FAQ? Have any doubt? Solution
Q.4
Which of the phrases given below should be placed in the blank space so
as to get a meaningful and grammatically correct sentence?
Although information technology has entered the homes, offices and
hearts of many Indian citizens, ________.
a. India provides the highest number of IT experts to the world every year.
b. many people in the rural areas still remain ignorant of its immense
benefits.
c. government has done its best by funding research in this field
appropriately.
d. the face of communication is likely to change completely in the years to
come.
Not Attempt Correct Ans. b
FAQ? Have any doubt? Solution
Q.5
The missing number of the series is ____________.
7 8 18 _____ 232 1165
Not Attempt Correct Ans. 57
FAQ? Have any doubt? Solution
Q.6
The paying capacity of people who travel on routes connecting smaller
towns is relatively low. Most successful airlines that operate in such
regions have a large number of seats.
http://s3.onlinetestseriesmadeeasy.in/madeeasy/index.php?pageName=timeManagementReport&testid=598&t=a&testType=2 2/20
2/5/2016 MADE EASY ONLINE TEST SERIES
Which of the following can be inferred based on the information given
above?
a. Regional airlines are quite profitable.
b. People from cities are increasingly travelling to smaller towns.
c. Regional airlines have to charge low fares in order to cover their
costs due to increased traffic.
d. The number of people travelling from small towns to cities is very large.
Not Attempt Correct Ans. c
FAQ? Have any doubt? Solution
Q.7
Three boxes labeled A, B and C have a total of 249 marbles. If 3 dozen
marbles are transferred from box ‘A’ to box ‘B’, box ‘B’ will have 5 times
the number of marbles in box ‘A’. Instead, if 21 marbles are transferred
from box ‘B’ to box ‘C’, the number of marbles in box ‘B’ will be 1.5 times
the number of marbles in box ‘C’. How many marbles should be
transferred from box ‘A’ or ‘B’ so that the number of marbles in both ‘A’
and ‘B’ is identical?
a. 30 from box ‘A’ to box ‘B’
b. 30 from box ‘B’ to box ‘A’
c. 36 from box ‘A’ to box ‘B’
d. 36 from box ‘B’ to box ‘A’
Not Attempt Correct Ans. b
FAQ? Have any doubt? Solution
Q.8
a. a unique pair
b. 2
c. 4
d. no valid solution
Not Attempt Correct Ans. d
FAQ? Have any doubt? Solution
Q.9
A book shelf has 27 books – 9 books each written by 3 eminent authors.
If Raj selects any 2 books without looking at their author’s name, what is
the probability that he picks up books written by different authors?
http://s3.onlinetestseriesmadeeasy.in/madeeasy/index.php?pageName=timeManagementReport&testid=598&t=a&testType=2 3/20
2/5/2016 MADE EASY ONLINE TEST SERIES
a.
b.
c.
d.
Not Attempt Correct Ans. d
FAQ? Have any doubt? Solution
Q.10
Venkat earns Rs 18,00,000 per annum which is spent under various
heads as under:
Food : 24%
Transportation and House rent : 19%
Clothing : 9%
Miscellaneous heads : 22%
Savings : 14%
Loan installment : Rs 18,000 per month.
If he cuts down his expenditure on food by 4.33% and his clothing
expense is down by 4% and the entire saving thus achieved is used to
pay off his loan, then the increase in the monthly installment of loan that
he can afford is Rs ______________ .
Q.11
If a rigid insulated container contains air and an electric heating coil is
also present, which heats the air when supply of current is switched on.
If the current is supplied through the wire then the process undergone by
gas will be
a. Isochoric
b. Isobaric
c. Adiabatic
d. Both (a) and (c)
http://s3.onlinetestseriesmadeeasy.in/madeeasy/index.php?pageName=timeManagementReport&testid=598&t=a&testType=2 4/20
2/5/2016 MADE EASY ONLINE TEST SERIES
Q.12
Water has critical specific volume of 0.003155 m3 /kg. A closed and rigid
steel tank of volume 0.03155 m3 , contains a mixture of water and steam
at 0.1 MPa. The mass of the mixture is 10 kg. The tank is now slowly
heated. The liquid level inside the tank
a. will rise
b. will fall
c. will remain same
d. may rise or fall depending on the amount of heat transferred
Q.13
Match ListI (Alloying element in steel) with ListII (Property conferred on
steel by adding the element) and select the correct answer using the
codes given below :
ListI ListII
A. Cobalt 1. Promotes deoxidization
B. Aluminium 2. Increases hardenability
C. Boron 3. Contributes to red hardness
D. Sulphur 4. Improves machinability of very low carbon steels
Codes:
A B C D
(a) 4 1 2 3
(b) 2 3 4 1
(c) 3 2 1 4
(d) 3 1 2 4
a. a
b. b
c. c
d. d
Q.14
The manometer shown contains two liquids. Liquid A has SG = 0.88 and
liquid B has SG = 2.95. The deflection h, when the applied pressure
difference is P1 – P2 = 860 Pa is
http://s3.onlinetestseriesmadeeasy.in/madeeasy/index.php?pageName=timeManagementReport&testid=598&t=a&testType=2 5/20
2/5/2016 MADE EASY ONLINE TEST SERIES
a. 10.58 mm
b. 21.17 mm
c. 42.35 mm
d. 64.70 mm
Q.15
A time standard for a data entry clerk is to be set. A job rated at 120 %
and takes 30 second to enter each records and the allowances are 15 %.
What is the normal time?
a. 25 sec
b. 30 sec
c. 36 sec
d. 41.4 sec
Q.16
When there is a flow of fluid over a flat plate of length ‘L’, the average
heat transfer coefficient is given by (Nux = Local Nusselt number ; other
symbols have usual meaning)
a.
b.
c.
d.
http://s3.onlinetestseriesmadeeasy.in/madeeasy/index.php?pageName=timeManagementReport&testid=598&t=a&testType=2 6/20
2/5/2016 MADE EASY ONLINE TEST SERIES
Q.17
If a piece of material neither expands nor contracts in volume when
subjected to stresses then the Poisson’s ratio must be
a. zero
b. 0.25
c. infinite
d. 0.5
Q.18
A solid round bar 6 cm in diameter and 250 cm long is used as a strut.
One end of the strut is fixed while its other end is hinged. The safe
compressive load for strut using Euler’s formula, assuming E = 200 GPa
and factor of safety = 2 is
a. 100 kN
b. 200 kN
c. 300 kN
d. 400 kN
Not Attempt Correct Ans. b
FAQ? Have any doubt? Solution
Q.19
Four solid spheres each of diameter √5 cm and mass 0.5 kg are placed
with their centers at the corners of a square of side 4 cm. The moment of
inertia of the system about the diagonals of the square is N × 10–4 kgm2 ,
then N is
a. 3
b. 6
c. 9
d. 18
Not Attempt Correct Ans. c
FAQ? Have any doubt? Solution
Q.20
A spherical drop of molten metal of radius 2 mm was found to solidify is
10 s. A similar drop of radius 8 mm would solidify in
http://s3.onlinetestseriesmadeeasy.in/madeeasy/index.php?pageName=timeManagementReport&testid=598&t=a&testType=2 7/20
2/5/2016 MADE EASY ONLINE TEST SERIES
a. 14.14 s
b. 120 s
c. 160 s
d. 190 s
Not Attempt Correct Ans. c
FAQ? Have any doubt? Solution
Q.21
The tool material in electro discharge machining is
a. Copper
b. Tin
c. Diamond
d. Lead
Q.22
A water turbine delivering 10 MW power is to be tested with the help of a
geometrically similar 1 : 16 model, running at the double speed as that of
the prototype. The power developed by model will be
a. 35.14 W
b. 76.29 W
c. 114.44 W
d. 228.88 W
Not Attempt Correct Ans. b
FAQ? Have any doubt? Solution
Q.23
What is the ratio of thermal conductivity to electrical conductivity equal
to ?
a. Prandtl number
b. Schmidt number
c. Lorenz number
d. Lewis number
Q.24
The Laplace transform of cos (4t) sin (2t) is
http://s3.onlinetestseriesmadeeasy.in/madeeasy/index.php?pageName=timeManagementReport&testid=598&t=a&testType=2 8/20
2/5/2016 MADE EASY ONLINE TEST SERIES
a.
b.
c.
d.
Not Attempt Correct Ans. b
FAQ? Have any doubt? Solution
Q.25
If A2 – A + I = 0, then the inverse of A is
a. A
b. A + I
c. I – A
d. A – I
Q.26
A wall of 0.5 m thickness is to be constructed from a material which has
an average thermal conductivity of 1.4 W/mK. The wall is to be insulated
with a material having an average thermal conductivity of 0.35 W/mK so
that the heat loss per square metre will not exceed 1450 W. Assuming
that the inner and outer surface temperature are 1200 °C and 15 °C
respectively. The thickness of insulation required is ______________
metre.
Q.27
For a crank and slotted lever mechanism, the length of the stroke is
360.3 mm. The ratio of time of cutting stroke to the time of return stroke
is __________. Line of stroke passes through the extreme positions of
the free end of the lever. Length of slotted lever is 450 mm.
http://s3.onlinetestseriesmadeeasy.in/madeeasy/index.php?pageName=timeManagementReport&testid=598&t=a&testType=2 9/20
2/5/2016 MADE EASY ONLINE TEST SERIES
Q.28
A carbide tool (having n = 0.25) with a mild steel workpiece was found to
give life of 1 hr 21 min while cutting at 60 m/min, n is the Taylor’s
exponent. The velocity when tool life is 3 hr 45 min is m/min will be
__________ m/min.
Q.29
In a rolling process, sheet of 25 mm thickness is rolled to obtain 20%
reduction. Roll is of diameter 500 mm and rotates at 250 rpm. The roll
strip contact length will be ___________ mm.
Q.30
A 400 m long horizontal pipe is to deliver 1000 kg of oil (s = 0.9, ν =
0.0002 m2 /s) per 60 seconds. If the head loss is not to exceed 800 cm of
oil, the pipe diameter is ____________ m.
[Friction factor for laminar flow : f = 64/Re ]
Q.31
If two reversible heat engines are working in series, such that heat
source of first engine is at 1300 K and the efficiencies of both engines
are same, then the temperature of intermediate reservoir is _________
K.
[Take Ambient temperature = 300 K]
Q.32
For an Otto cycle, the efficiency of the cycle is 54%. The temperature at
the start of compression is 15 °C. The temperature after compression is
_____________ K.
http://s3.onlinetestseriesmadeeasy.in/madeeasy/index.php?pageName=timeManagementReport&testid=598&t=a&testType=2 10/20
2/5/2016 MADE EASY ONLINE TEST SERIES
Q.33
A full journal bearing having diametral clearance to diameter ratio of
, using a lubricant with viscosity (Z ) of 28 × 10–3 Pas, support the
shaft journal running at N = 2400 rpm. If bearing pressure is 1.4 MPa. The
Sommerfeld number is ____________ × 10–3 .
Q.34
The area enclosed between the curve y = loge (x + e
) and the coordinate
axes is _________.
Not Attempt Correct Ans. 1
FAQ? Have any doubt? Solution
Q.35
If then the value of div curl at (1, –1, 1) is
___________.
Q.36
A linear programming problem is shown below:
Maximize Z = 3x + 2y
Subject to
It has
a. an infeasible solution.
b. exactly one optimal solution
c. exactly two optimal solution
d. infinitely many optimal solution
http://s3.onlinetestseriesmadeeasy.in/madeeasy/index.php?pageName=timeManagementReport&testid=598&t=a&testType=2 11/20
2/5/2016 MADE EASY ONLINE TEST SERIES
Q.37
A shopkeeper forecasts the demand of cycles at rate of 1000 per
months for the next three months. The actual demand turned out to be
800,1320 and 1400. The BIAS of the forecast will be
a. 53
b. 53
c. 173
d. 173
Q.38
The average heat produced by oranges ripening is estimated to be 300
W/m2 . Taking the average diameter of an orange to be diameter 8 cm
and assuming it to be a sphere with k = 0.15 W/mK, the temperature at
the centre of orange when outer surface is maintained at 10 °C is
a. 25 °C
b. 50 °C
c. 75 °C
d. 100 °C
Q.39
The homogeneous state of stress for a metal part undergoing plastic
deformation is given by
Where the stress component values are in MPa. Using Von mises yield
criterion, the value of estimated yield stress in MPa is
a. 6.61
b. 8.65
c. 13.23
d. 18.70
http://s3.onlinetestseriesmadeeasy.in/madeeasy/index.php?pageName=timeManagementReport&testid=598&t=a&testType=2 12/20
2/5/2016 MADE EASY ONLINE TEST SERIES
Q.40
A solid aluminium shaft, 5 cm diameter and 1 m long, is to be replaced
by a tubular shaft of the same length and the same outside diameter (i.e.
5 cm), such that each of the two shaft could have the same angle of twist
per unit torsional moment over the total length. Modulus of rigidity of
steel is three times that of aluminium. The inner diameter of the tubular
shaft is
a. 2.5 cm
b. 3.5 cm
c. 4.5 cm
d. 4.0 cm
Q.41
The shear force diagram for a beam ABCDE, supported at A and one
more points is shown in figure. The maximum bending moment is
a. 164 kNm
b. 185 kNm
c. 225 kNm
d. 284 kNm
Q.42
Two mating gear have 20 and 40 involute teeth of module 10 mm and 20°
pressure angle. The addendum on each wheel is to be made such that
the line of contact on each side of the pitch points has half the maximum
possible length. The ratio of addendum for pinion to Gear will be
a. 2
b. 2.5
c. 3.5
d. 0.4
http://s3.onlinetestseriesmadeeasy.in/madeeasy/index.php?pageName=timeManagementReport&testid=598&t=a&testType=2 13/20
2/5/2016 MADE EASY ONLINE TEST SERIES
Not Attempt Correct Ans. b
FAQ? Have any doubt? Solution
Q.43
For the system, shown below, when block is displaced a little against
spring C, what will be the time period of oscillations? The mass of block
is 1 kg and all the springs have spring constant 10 N/m.
a. 0.461s
b. 1 s
c. 1.286 s
d. 1.404 s
Q.44
In an orthogonal cutting, operation,
uncut chip thickness = 0.32 mm
shear plane angle, φ = 30°
shear velocity = 2.2 m/s
The strain rate is
a. 1437.5 s–1
b. 2875 s–1
c. 3437.5 s–1
d. 4837.5 s–1
Q.45
For a 50 mm shaft and hole pair designated H7 S8 , the basic size lies in
the range of 50 – 80 mm.
Data : For Tolerance
H7 16i
S8 25i
The fundamental deviation for ‘S ’ shaft is (IT 7 + 0.4D) microns.
http://s3.onlinetestseriesmadeeasy.in/madeeasy/index.php?pageName=timeManagementReport&testid=598&t=a&testType=2 14/20
2/5/2016 MADE EASY ONLINE TEST SERIES
The allowance in mm will be
a. 0.1
b. 0.2
c. 0.3
d. 0.4
Not Attempt Correct Ans. a
FAQ? Have any doubt? Solution
Q.46
A heat engine is used to drive the refrigerator. Efficiency of heat engine
and COP of refrigerator are 60% and 5 respectively. Heat input (in
kJ/sec) needed to the heat engine from the higher temperature source
for each ton of refrigeration is
a. 1.00
b. 0.58
c. 1.17
d. 2.33
Q.47
A riveted joint (with 4 rivets numbered 1 to 4) as shown in figure is
subjected to an eccentric loading. The most and least stressed rivets
respectively are :
a. 4 and 2
b. 2 and 4
c. 1 and 3
d. 3 and 1
Q.48
A block of area A having mass m slides down a smooth inclined plane, θ
http://s3.onlinetestseriesmadeeasy.in/madeeasy/index.php?pageName=timeManagementReport&testid=598&t=a&testType=2 15/20
2/5/2016 MADE EASY ONLINE TEST SERIES
with the horizontal on a film of oil having viscosity μ and having its
thickness d. If the block is released from rest at t = 0, the expression for
the speed of block as a function of time will be
a.
b.
c.
d.
Not Attempt Correct Ans. a
FAQ? Have any doubt? Solution
Q.49
In the figure shown below the workdone is maximum when
(for a given temperature Tmin = T1 and T3 = Tmax )
a. Only 1 is satisfied
b. Only 3 is satisfied
c. 1, 2, and 3 are satisfied
d. Only 2 is satisfied
Q.50
If a discrete random variable X has the following probability distribution,
then the standard deviation is
http://s3.onlinetestseriesmadeeasy.in/madeeasy/index.php?pageName=timeManagementReport&testid=598&t=a&testType=2 16/20
2/5/2016 MADE EASY ONLINE TEST SERIES
a. 0.5
b. 1
c. √2
d. 2
Q.51
The value of , is
a.
b. a π
c. 2 π
d.
Not Attempt Correct Ans. a
FAQ? Have any doubt? Solution
Q.52
Two 8 mm thick steel plates are placed 5 mm apart and welded by a butt
joint. Welding is carried out at 20 V. Heat transfer efficiency is 0.80. If the
heat required to melt steel is 10 J/mm3 and melting efficiency is 0.625.
The weld current (in A) is 200 A. The welding speed in mm/s is
__________.
Q.53
If the stream function is given by y = 3xy, then the velocity at a point (2,
3) will be ________ unit.
Q.54
http://s3.onlinetestseriesmadeeasy.in/madeeasy/index.php?pageName=timeManagementReport&testid=598&t=a&testType=2 17/20
2/5/2016 MADE EASY ONLINE TEST SERIES
The maximum work that can be obtained, if one kg of water at 90 °C is
cooled to ambient temperature of 27 °C is _____________kJ. (Specific
heat of water = 4.18 kJ/kgK).
Q.55
A block is moving on a inclined plane making an angle 45° with the
horizontal and the coefficient of friction is μ. The force required to push
block up the inclined plane is 3 times the force required to just prevent it
from sliding down. Then μ is ____________.
Q.56
A project has four activities P, Q, R and S as shown below
The fixed cost of the project is Rs 10,000 and the overhead cost is Rs
200 per day. If the project duration to be crashed down to 9 days, the
total cost (in Rs) of the project is _________.
Q.57
A column of square section 40 mm × 40 mm, fixed to the ground carries
an eccentric load of P Newton as shown in the figure.
http://s3.onlinetestseriesmadeeasy.in/madeeasy/index.php?pageName=timeManagementReport&testid=598&t=a&testType=2 18/20
2/5/2016 MADE EASY ONLINE TEST SERIES
If the stresses developed along the edge CD and AB is –1.2 N/mm2 and
–0.8 N/mm2 respectively. The eccentricity is ____________ mm.
Q.58
A fixed gear having 200 teeth is in mesh with another gear having 50
teeth. The two gear are connected by an arm. The number of turns made
by smaller gear for one revolution of arm about the centre of the bigger
gear is __________.
Q.59
A turning tool with sharp corner and a major cutting edge angle of 50° is
being used at a feed of 0.05 mm. Another cutting tool has a nose radius
of 1.8 mm and feed of 0.268 mm. The minor cutting edge angle of the
turning tool for the same surface roughness of the two tools will be
_________ degrees.
Q.60
A hemispherical cup of Radius 10 cm is formed in a pressworking
operation. The radius of blank would be ___________ cm.
Q.61
0.4 ms–2 . At t = 2s, the sum of coordinates of the particle that passed
through point (1, 2) at t = 0 will be _________.
Q.62
http://s3.onlinetestseriesmadeeasy.in/madeeasy/index.php?pageName=timeManagementReport&testid=598&t=a&testType=2 19/20
2/5/2016 MADE EASY ONLINE TEST SERIES
A fan is to accelerate quiescent air to a velocity of 12 m/s at a rate of 3
m3 /sec. If the density of air is 1.15 kg/m3 , the minimum power that must
be supplied to the fan is ___________ Watt.
Q.63
A disk clutch is required to transmit 10 kW at 1000 rpm. Coefficient of
friction lining is 0.2. Outside radius of friction lining is 60 mm. If uniform
contact pressure is 1.2 MPa, then the bore radius of friction lining is
____________ mm.
Q.64
Q.65
http://s3.onlinetestseriesmadeeasy.in/madeeasy/index.php?pageName=timeManagementReport&testid=598&t=a&testType=2 20/20