Beruflich Dokumente
Kultur Dokumente
Diameter
Piping
Systems
⊕⊕
R
The System
The Victaulic® grooved method for mechanically joining pipe has been used
successfully for over 70 years to simplify design, installation, and operation
of piping systems. It combines the advantages of fast installation, design
integrity and reliable operation at lower total installed cost than other
conventional methods.
Victaulic technology for joining large diameter piping includes capabilities
for direct grooving black or galvanized steel pipe up to 42" (1050 mm). The
Vic-Ring® applied ring method accommodates odd pipe sizes up to 144"
(3600 mm).
The Victaulic system for joining large diameter pipe and piping components
are available from stocking distributors worldwide. Over 200 factory-trained
piping specialists provide on-site assistance backed by application and
product engineering support as close as your phone.
2
Diversified
3
Economical
A B
4
Certified
5
Applications
Water
■ Chilled
■ Heating
■ Condenser
■ Supply
■ Underground
■ Wastewater
Other
■ Compressed air
■ Slurries
■ Tailings
Galvanized steel pipe, 30 - 42" (750 - 1050 mm), was easily direct grooved and coupled with Style 770 couplings
for these condenser water lines in a large office complex in Singapore. The system was then painted to color code
and for aesthetics.
Vic®-Ring applied rings allowed easy bolted coupling assembly for these Large diameter ductile iron pipe was radius cut grooved and assembled for
power plant water supply lines. underground fire protection water supply.
6
Applications
Markets
■ Heating/Air
Conditioning
■ Plumbing
■ Industrial
■ Mining
■ Power Plant
■ Marine
■ Dredging
Large mine tailings such as these lines at BP Minerals, Bingham Canyon and other abrasive services utilize the
full wall thickness and the option to rotate pipe sections available with Vic-Ring applied ring piping.
Large diameter valves are available Direct grooved pipe was easily assembled for these chilled water lines at a large hotel in Dubai, UAE.
with grooved or shouldered ends to
allow easy positioning, assembly
and future maintenance with the
Victaulic system, such as these
Style 770 grooved couplings. These
systems were installed at Prospect
Water Treatment Facility in
Sydney, Australia.
7
Grooved System
OD C
Roll Vic-Easy
A B A B
grooving tools roll a
removes groove
Hydraulic
no metal Force into pipe
Upper Roll from pipe
Pipe
Pipe
Lower
(Drive)
Roll
8
Couplings
Style 770 Style 770 couplings are Roll Grooved NOTE: Bolts and nuts
Large Diameter designed to provide a Beveled or square cut pipe must be torqued to
Pipe Coupling strong reliable component of 0.375" or 0.500" (9.5 or listed specifications
for joining large diameter 12.7 mm) wall thickness during installation.
piping systems. Style 770 can be roll grooved with This product requires
provides a joint with special Vic-Easy® roll special roll grooving
flexibility to accommodate grooving tools. Grooving equipment, pipe specifi-
settlement and alignment. must be performed by Vic- cations, and mandatory
Ranging in size from 28" taulic trained personnel. installation training.
(700 mm) to 42" (1050 mm), Contact Victaulic for details Refer to I-770 for
Style 770 is ideal for roll on other wall thicknesses. product installation
grooved black or galvanized instructions.
Cut Grooved
steel and stainless steel
Cut Grooving may be used
systems up to 330 PSI (2270
for pipe wall thickness
kPa) depending on pipe
0.625" (15.9 mm) or thicker.
size, wall thickness and
material. Contact Victaulic for
details.
Compatible roll grooved fit-
tings to ANSI B-16.9 cen-
ter-to-end dimensions are
also available.
Y Z
Y Z
X
X
NOTES
* Working Pressure and End Load are total, from all internal and external loads, based on ANSI standard weight (0.375"/9.5 mm) steel pipe, standard roll grooved
in accordance with Victaulic® specifications and with bolts fully torqued to listed specifications. Contact Victaulic for performance on other pipe.
WARNING: FOR ONE TIME FIELD TEST ONLY, the Maximum Joint Working Pressure may be increased to 1¹⁄₂ times the figures shown.
‡ Pipe End Separation and Deflection figures show the nominal range of movement available at each joint for standard roll grooved pipe. For design and installation
purposes these figures should be reduced by 25% to allow for pipe groove tolerances. NOTE: Joints which are fully deflected can no longer provide linear move-
ment. Partially deflected joints will provide some portion of linear movement. Pressure thrusts will tend to straighten deflected pipe.
@ Number of bolts required equals number of housing segments.
Metric thread size bolts are available (color coded gold) for all coupling sizes upon request. Contact Victaulic for details.
WARNING: Piping systems must always be depressurized and drained before attempting disassembly and removal of any Victaulic piping products.
9
Fittings
1410-2B
PERFORMANCE PIPE
Carbon Steel Stainless Steel
PIPE ¹⁄₂"/12.7 mm ³⁄₈"/9.5 mm ¹⁄₄"/6.4 mm ¹⁄₄"/6.4 mm
Inches/mm Wall Thickness Wall Thickness Wall Thickness* Wall Thickness*
Max. Max. Max. Max. Max. Max. Max. Max.
Work End Work End Work End Work End
Nominal Actual Press. Load Press. Load Press. Load Press. Load
Size Size PSI/kPa Lbs./N PSI/kPa Lbs./N PSI/kPa Lbs./N PSI/kPa Lbs./N
28 28.00 380 233986 330 203198 132 81279 110 67733
700 711 2620 1040822 2270 903870 910 361547 760 301291
30 30.00 348 245987 300 212058 120 84823 100 70686
750 762 2400 1094205 2065 943281 826 377312 690 314427
32 32.00 300 241274 260 209104 105 84446 85 68361
800 813 2065 1073240 1790 930141 724 375635 585 304085
36 36.00 232 236147 200 203575 80 81430 75 76341
900 914 1600 1050434 1379 905547 552 362219 517 339582
42 42.00 165 228598 145 200889 55 76199 50 69272
1050 1067 1138 1016855 1000 893599 379 338950 345 308137
*Ratings are based upon pipe grooved with Victaulic R x rolls.
Direct Grooved Victaulic offers a broad line All fittings are supplied Machining for rubber lining
Fittings of fittings in sizes through with grooves to permit fast may be varied to provide
42" (1050 mm) in a variety installation without field abrasion resistance only or
of straight and reducing preparation. The grooved both abrasion and corrosion
styles. Standard fittings are design permits flexibility resistance.
steel, segmentally welded for easy alignment.
Lining may be applied on
steel or ductile iron
Fitting center-to-end the inside diameter and
depending on styles and
dimensions will vary end (abrasion resistance) or
size. Fittings are painted
depending upon type and wrap-around for corrosion
with galvanized optionally
schedule. and/or abrasion. Request
available, contact Victaulic
for details. 25.03 or contact Victaulic
Rubber or Urethane for specific details.
Victaulic fittings pressure Lining (MRL) – For severe
ratings conform to the rat- abrasive services, Victaulic
fittings may be rubber or
ings of the particular cou-
urethane lined (by others).
pling style used for
assembly.
C to E
C to E
C to E
C
to
E
PIPE
Inches/mm No. 100 – 90° No. 110 – 45° No. 20 – Tee
Nom. Actual C-E Wgt. Ea. C-E Wgt. Ea. C-E Wgt. Ea.
Size Size In./mm Lbs./kg In./mm Lbs./kg In./mm Lbs./kg
28 28.000 42.00 626.0 17.25 312.0 24.00 790.0
700 711 1066 284 438 142 610 358
30 30.000 45.00 775.0 18.50 358.0 25.00 1000.0
750 762 1143 352 470 162 635 454
36 36.000 54.00 1170.0 22.25 583.0 30.00 1450.0
900 914 1372 531 565 265 762 658
42 42.000 63.00 1810.0 26.00 900.0 35.00 2000.0
1050 1067 1600 821 660 408 889 907
Ductile iron available. Contact Victaulic for sizes, dimensions and availability.
10
Tools
Direct Grooved
Piping from 28 - 42" the pipe wall as the pipe is Coupling weight is less
Pipe Preparation (700 - 1050 mm) can now rotated by a lower female than one-half, ranging from
be direct roll grooved to drive roll forming the 175 - 450 lbs. (79 - 204 kg)
receive new Style 770 large groove. vs. 440 - 980 lbs. (200 -
diameter couplings. This 445 kg) for flanges.
The grooved system has far
capability brings the speed
fewer bolts than flanged Victaulic shop roll groovers
and ease of bolted mechan-
systems, for example: 30" can roll groove up to ¹⁄₂"
ical assembly to large diam-
(750 mm) requires six bolts (13 mm) wall thickness car-
eter pipe assembly.
for a Victaulic coupling, bon steel pipe.
Roll grooving removes flanging requires 28 bolts;
no metal, cold forming a 42" (1050 mm) requires
groove by the action of an eight bolts, compared to
upper male roll displacing 36 bolts.
Large Diameter The Victaulic Large Diame- 0.375" (9.5 mm). The tool is grooving pipe in the follow-
Pipe Roll ter Roll Groover is a fully supplied with 4 - 24" ing sizes: 22 - 24"
motorized, automated shop (100 - 600 mm) rolls as stan- (550 - 600 mm) and 30 - 36"
Grooving Tool tool for continuous produc- dard. Optional rolls avail- (750 - 900 mm) up to maxi-
tion grooving. It is supplied able are 4 - 24" (100 - mum wall thickness of .500"
in several variations to 600 mm) lightwall stainless (12.7 mm). These rolls are
accommodate the needs of steel pipe, 4 - 12" (100 - standard supply with this
roll grooving pipe above 24" 300 mm) “ES” grooving, tool. Other roll sets can be
(600 mm). and a conversion kit for provided upon request.
grooving 26 - 36" (650 -
The VE424 is a fully auto- For roll grooving 42"
900 mm) standard wall
mated shop tool for roll (1050 mm) pipe, contact
.375" (9.5 mm) steel pipe.
grooving pipe from 4 - 36" Victaulic.
(100 - 900 mm) with a maxi- The VE436 is a fully auto-
mum wall thickness of mated shop tool for roll
1410-4B
1 2 3 5 4 6 7 8
Roll/Cut Groove Dimensions – Inches/mm
Specifications Pipe Groove Width Min. Allow. Wall
for Style 770 Large Nom. Outside Diameter O.D. Gasket “B” Groove Dia. Thickness
Inches/mm ±0.03/±0.76 “C” Grv. “T” Max.
Diameter Couplings Pipe Seat
Size “A” Tol. Depth Allow.
B
Inches +0.03/–0.06 Roll Cut +0.000 “D” Roll Cut Flare
A B T mm Basic Tolerance +0.8/–1.5 Groove Groove Basic +0.00 (Ref.) Groove Groove Dia.
28 O.D. 28.00 +0.093 –0.031 1.75 0.625 0.625 27.50 –0.063 0.250 0.250 0.625 28.20
700 711.0 +2.36 –0.79 44.45 15.88 15.88 698.50 –1.60 6.35 6.35 15.88 716.3
30 O.D. 30.00 +0.093 –0.031 1.75 0.625 0.625 29.50 –0.063 0.250 0.250 0.625 30.20
OD C 750 762.0 +2.36 –0.79 44.45 15.88 15.88 749.30 –1.60 6.35 6.35 15.88 767.1
32 O.D. 32.00 +0.093 –0.031 1.75 0.625 0.625 31.50 –0.063 0.250 0.250 0.625 32.20
800 813.0 +2.36 –0.79 44.45 15.88 15.88 800.10 –1.60 6.35 6.35 15.88 817.9
36 O.D. 36.00 +0.093 –0.031 1.75 0.625 0.625 35.50 –0.063 0.250 0.250 0.625 36.20
Exaggerated for Clarity 900 914.0 +2.36 –0.79 44.45 15.88 15.88 901.70 –1.60 6.35 6.35 15.88 919.5
D
42 O.D. 42.00 +0.093 –0.031 2.00 0.625 0.625 41.50 –0.063 0.250 0.250 0.625 42.20
1050 1067.0 +2.36 –0.79 50.80 15.88 15.88 1054.10 –1.60 6.35 6.35 15.88 1071.8
COLUMN 1: Nominal IPS Pipe size.
COLUMN 2: IPS outside diameter. The outside diameter of roll grooved pipe shall not vary more than the tolerance listed. For IPS pipe the maximum allowable tolerance from square cut ends
is 0.060" (1.5 mm) for sizes 28" (700 mm) and above measured from true square line.
COLUMN 3: Gasket seat. The pipe surface shall be free from indentations, roll marks, and projections from the end of the pipe to the groove, to provide a leaktight seal for the gasket. All loose
paint, scale, dirt, chips, grease and rust must be removed. It continues to be Victaulic Company’s first recommendation that pipe be square cut. When using beveled pipe contact Victaulic for
details. Gasket seat “A” is measured from the end of the pipe. IMPORTANT: Roll grooving of beveled end pipe may result in unacceptable pipe end flare. See column 8.
COLUMN 4: Groove width. Bottom of groove to be free of loose dirt, chips, rust and scale that may interfere with proper coupling assembly. Corners at bottom of groove must be radiused. For
IPS steel pipe, R-0.015" (0.38 mm) ±0.005 (0.13 mm).
COLUMN 5: Groove outside diameter. The groove must be of uniform depth for the entire pipe circumference. Groove must be maintained within the “C” diameter tolerance listed.
COLUMN 6: Groove depth. For reference only. Groove must conform to the groove diameter “C” listed.
COLUMN 7: Minimum allowable wall thickness. This is the minimum wall thickness which may be roll grooved.
COLUMN 8: Maximum allowable pipe end flare diameter. Measured at the most extreme pipe end diameter square cut or beveled.
11
Vic-Ring
Vic-Ring Configurations
12
Couplings
plings are supplied with “E” Coupling Dimensions Bolt Dimensions Aprx.
or “T” gaskets. FlushSeal® Inches/mm Inches/mm Weight
Size Each
gaskets are available upon Inches Height Width Depth Lbs.
request. mm X Y Z No. Dia. ✕ Lgth. kg
30 36.25 40.25 5.00 178.0
All sizes are supplied 750 921 1022 127 6 1¹⁄₈ ✕ 5¹⁄₂ 80.7
painted with alkyd phenolic 36 42.50 46.50 5.00
6 1¹⁄₈ ✕ 5¹⁄₂
205.0
900 1080 1181 127 93.0
primer and with plated nuts
38 44.50 48.50 5.13 220.0
and bolts. 950 1130 1232 130 6 1¹⁄₄ ✕ 5¹⁄₂ 99.8
42 49.13 55.00 5.13 270.0
Request 16.04. 1050 1248 1397 130 8 1³⁄₈ ✕ 5³⁄₄ 122.5
46 52.25 58.75 5.38 330.0
1150 1327 1492 137 8 1¹⁄₂ ✕ 5³⁄₄ 149.7
48 55.63 62.00 5.25 390.0
1225 1413 1575 133 8 1⁵⁄₈ ✕ 6 176.9
54 62.25 69.50 5.38 470.0
1350 1581 1765 137 8 1³⁄₄ ✕ 6 213.2
60 68.63 76.00 5.50 570.0
1500 1743 1930 140 10 1⁷⁄₈ ✕ 6 258.6
66 74.88 81.00 6.88 750.0
1650 1902 2057 175 24 1¹⁄₂ ✕ 5³⁄₄ 340.2
13
Couplings
Style 44
16.05-1B
Vic-Ring® Coupling Dimensions Bolt Dimensions Aprx.
Coupling Inches/millimeters Inches/millimeters Weight
Size Each
Y Z Inches Height Width Depth Lbs.
mm X Y Z No. Dia. ✕ Lgth. kg
4 6.88 9.25 2.13 8.0
100 175 235 54 2 ⁵⁄₈ ✕ 4 3.6
X
6 9.13 11.50 2.25 11.0
150 232 292 57 2 ⁵⁄₈ ✕ 4 5.0
8 11.88 14.50 2.50 17.0
200 302 368 64 2 ³⁄₄ ✕ 5 7.7
4 - 12 sizes
10 14.13 16.75 2.69 23.0
2 ³⁄₄ ✕ 5
Style 44 couplings are 250 359 425 68 10.4
Y Z
designed with cross-ribbed 12 16.63 19.50 2.81 31.0
300 422 495 71 2 ⁷⁄₈ ✕ 5¹⁄₂ 14.1
construction to provide a 14 18.75 22.50 2.75 43.0
strong component for use 350 476 572 70 4 1 ✕ 3¹⁄₂ 19.5
on steel pipe with applied 16 21.00 25.25 3.50
4 1 ✕ 3¹⁄₂
63.0
X 400 533 641 89 28.6
Vic-Ring adapters. Many
18 24.25 28.00 3.69 85.0
sizes may be used on pipe 450 616 711 94 4 1 ✕ 3¹⁄₂ 38.6
with cast shoulders. 20 26.13 30.50 3.50 90.0
500 664 775 89 4 1¹⁄₄ ✕ 5¹⁄₂ 40.8
14 - 20" sizes Style 44 couplings are sup- 24 30.13 35.00 3.50 107.0
600 765 889 89 6 1¹⁄₄ ✕ 3¹⁄₂ 48.5
plied with “E” or “T” gas-
kets. FlushSeal® gaskets 30 37.63 43.00 5.19 225.0
750 956 1092 132 6 1¹⁄₂ ✕ 5³⁄₄ 102.1
Y Z
are available upon request. 36 44.25 50.00 5.13 270.0
900 1124 1270 130 6 1¹⁄₂ ✕ 5³⁄₄ 122.5
All sizes are supplied 42 50.63 57.50 5.25 380.0
painted with alkyd phenolic 1050 1286 1461 133 8 1³⁄₄ ✕ 6 172.4
X primer and with plated nuts 48 57.63 63.00 6.50 515.0
1200 1464 1600 165 16 1³⁄₈ ✕ 5³⁄₄ 233.6
and bolts. 54 64.50 70.50 6.88 615.0
1350 1638 1791 175 16 1¹⁄₂ ✕ 5³⁄₄ 279.0
Request 16.05. 60 71.25 77.00 6.88 688.0
1500 1810 1956 175 20 1¹⁄₂ ✕ 5³⁄₄ 312.1
24 - 36" sizes
Y Z Y Z
Style 31 Style 31 couplings are com-
Vic-Ring® monly used with Type “D”
Coupling or “E” Vic-Ring adapters
and are designed to provide X X
a strong component for use
on ductile iron pipe with
applied Vic-Ring adapters.
Many sizes may be used on 14 - 20" sizes 24 - 36" size
pipe with cast shoulders.
Style 31 Vic-Ring cou- 16.03-1B
14
Vic-Ring
Pipe Max. Work. Coupling Selection Pipe Max. Work. Coupling Selection
O.D. Press.* Size Vic-Ring O.D. Press.* Size Vic-Ring
In./mm PSI/kPa Inches/mm Style Type In./mm PSI/kPa Inches/mm Style Type
14 175 14 38 90 38
350 1207 350 31 D, E 950 620 950 41 D, E
16 200 17 42 175 42
400 1380 430 22 A 1050 1207 1050 44 D, E
16 175 16 42 90 42
400 1207 400 44 D, E 1050 620 1050 41 D, E
18 175 18 46 90 46
450 1207 450 31 D, E 1175 620 1175 41 D, E
20 200 20 48 175 48
500 1380 500 22 A 1200 1207 1200 44 D, E
20 175 20 48 90 48
500 1207 500 31 D, E 1200 620 1200 41 D, E
24 200 24 54 175 54
600 1380 600 22 A 1375 1207 1375 44 D, E
24 175 24 54 90 54
600 1207 600 31 D,E 1375 620 1375 41 D, E
30 175 30 60 175 60
750 1207 750 44 D, E 1525 1207 1525 44 D, E
30 150 30 60 90 60
750 1035 750 22 A 1525 620 1525 41 D, E
30 90 30 66 90 66
750 620 750 41 D, E 1675 620 1675 41 D, E
36 175 36
900 1207 900 44 D, E
For complete Vic-Ring adapter dimensions for the above selections, as well as Victaulic couplings data, refer to Sections 16.02 through 16.06. For coupling/ring combinations not
shown, or for other applications, contact Victaulic for details.
* Working Pressures are total, from all internal and external loads, based on ANSI standard weight steel pipe, with Vic-Rings applied in accordance with Victaulic specifications.
Contact Victaulic for performance on other pipe.
15
Gasket Data
Gasket Data
Unique “C” shaped gasket Seals between the pipe ends Surrounded, reinforced and Seal is enhanced by pressure
forms a triple seal and the groove slightly compressed by the housing of vacuum in the line
The sealing efficiency of The combination of these The Victaulic gasket design (250 mm) of mercury, the use of
Victaulic gaskets is such that the characteristics creates a seals equally well under vacuum. molded FlushSeal® gaskets or
gasket forms an initial seal as it permanent, leak-tight triple seal Vacuum creates a pressure standard gaskets with metal
is stretched over the pipe ends. on a variety of piping materials differential between the inside liners is recommended.
Upon placement of the housing including carbon steel, stainless and outside of the piping FlushSeal gaskets comprised of
around the gasket and into the steel, aluminum, PVC, cast iron system. The resulting increased standard gaskets with rubber
grooves, the gasket is and copper. force from external pressure filler strip inserts are not
positioned. As the housing Line pressure serves to differential has the same seal recommended for vacuum
segments are tightened, the strengthen the seal through the strengthening effect as internal services greater than 10"
resilient elastomeric gasket combination of normal gasket pressure. (250 mm) of mercury.
conforms to the internal cavity resilience, housing Due to the forces applied at the For more details about Victaulic
of the housing and is further reinforcement and the action of center of the gasket under gasket construction and testing,
compressed, enhancing the pressure downward on the lips. vacuum service greater than 10" request 05.01.
gasket’s seal against the pipe.
The Victaulic gasket is pressure
responsive.
16
Design Data
Design Considerations
piping runs that will experience accumulated growth (∆L) as the
The Victaulic large diameter piping method may be used for joining a
system is pressurized. Note also that thermal expansion of pipes will
variety of piping systems for a variety of services. It may be utilized for
add to the total movement in these cases.
varied pipe sizes, pipe materials and wall thickness. Large diameter
products are available to provide flexible systems.
As with any piping method, the nature of the method should be
considered in designing the piping systems. This design data applies Pressure Zero
primarily to grooved end pipe, however, much of the information ∆L
applies to other Victaulic mechanical piping products used in
conjunction with grooved components.
The material presented is intended solely for piping design reference Line Pressurized
in utilization of Victaulic products for their intended application. It is
not intended as a substitute for competent, professional assistance
which is an obvious requisite to any specific application. Recommended Pipe
Hanger/Support Spacing Maximum Hanger/
PRESSURE THRUST for Flexible Systems Support Spacing
When a flexible grooved type mechanical coupling is sustaining forces Requiring Maximum Not Requiring
trying to separate the pipe ends, the shoulder of the groove is pulled Linear Movement Linear Movement
1410-5A 1410-6A
hard against the inside face of the coupling key. This is what prevents
Pipe Length
the pipes from separating. Feet/Meters
Nom.
The allowable force which a joint can sustain varies for different types 9.8 19.7 29.5 39.4
Pipe Nom. Maximum
of couplings, pipe wall thickness, types of pipes and grooving. The Size 3 6 9 12
Pipe Size Span
product data under the column “Maximum End Load” shows the Inches Hangers Per Inches Feet
maximum allowable end force that the couplings will sustain. mm Above Length mm Meters
28 28 20
700 1 2 3 3 700 6.1
30 30 20
750 1 2 3 3 750 6.1
32 32 21
800 1 2 3 3 800 6.4
36 36 21
900 1 2 3 3 900 6.4
PT D PT
42 42 21
1050 1 2 3 3 1050 6.4
π 2
PT = --- D p Pump
4
Oscillation
17
Design Data
ANCHORAGE AND SUPPORT 4" (100 mm) and larger – Reduce published figures by 25%
Standard cut grooved pipe will provide double the
expansion/contraction or deflection capabilities of the same
size standard roll groove pipe.
Where lines are likely to block or plug, joints and anchors (including
intermediate anchors) should be designed to withstand the
longitudinal pressure thrust or End Load created by the blockage.
ANGULAR DEFLECTIONS
Angular deflection available at flexible grooved pipe joints is
published under Performance Data for each Victaulic coupling style.
These values are MAXIMUMS. For design and installation purposes
these figures should be reduced by the following factors to allow for
pipe grooving tolerances (Refer to Sections 26.01 & 26.02 for more
details).
18
The Company
Quality, reliability,
and innovation since 1925
Victaulic Company is the originator and developer of the grooved piping method for rapidly
joining building service pipe. Victaulic has been used for many years for HVAC, plumbing,
fire protection and many specialized building service piping applications.
The Victaulic system has been approved, specified and used for building service piping by
GSA, VA, COE, NAVFAC and other federal agencies for many years. Applications include
chilled and hot water, condenser water, plumbing services, fire protection and general util-
ity services.
Victaulic has developed many products for the building market including two and three-
way actuated valves, flange adapters, rigid couplings and field pipe preparation too. Exten-
sive in-house product development and testing capabilities assure products designed and
manufactured for life-of-the-system reliability. Look to Victaulic for the finest pipe cou-
plings, fittings, valves and piping accessories.
19
www.victaulic.com
Customer Inquiries: pickvic@victaulic.com
Literature Requests: victaulic@victaulic.com
R
WORLD HEADQUARTERS
P.O. Box 31 • Easton, PA 18044-0031
4901 Kesslersville Road • Easton, PA, USA 18040
Phone: 610/559-3300 • FAX: 610/250-8817