Beruflich Dokumente
Kultur Dokumente
Alliages cuivre-zinc corroyks - Composition chimique et formes des produits corroy& - Partie 2: Ailiages de cuivre-zinc au
plomb
Descri ptors : copper al l oys, zi n c-con tai n i n g al l oys, l ead -con tai n i n g al l oys, brasses, ch em i cal com posi ti on , wrou g h t prod u cts.
IS0 (th e In tern ati on al Org an i zati on for Stan d ard i zati on ) i s a worl d wi d e fed erati on of
nati on al stand ard s bodi es (IS0 mem ber bod i es). Th e work of d evel opi n g I ntern ati on al
Stan d ard s i s carri ed ou t th rou g h IS0 tech ni cal com mi ttees. Every mem ber bod y
i n terested i n a subj ect for wh ich a techn i cal com mi ttee h as been au th ori zed has th e
ri g h t to be represen ted on th at comm i ttee. In tern ati on al org an i zati on s, g overn m en tal
Draft In tern ati on al Stan d ard s ad opted by th e techn i cal com mi ttees are ci rcul ated to
th e m ember bodi es for approval before th ei r acceptan ce as In tern ati on al Stan d ard s by
th e IS0 Cou n ci l .
In ternati on al Stan d ard IS0 426/2 was d evel oped by Tech n i cal Comm i ttee I SO/TC 26,
Copper and copper alloys, an d was ci rcu l ated to th e mem ber bodi es in
November 1 981 .
I t has been approved by th e m ember bodi es of th e fol l owi n g cou n tri es:
Fi n l an d Rom an i a
Th e m ember bod i es of th e fol l owi ng cou n tri es expressed d i sapproval of th e d ocu m ent
Fran ce
Swi tzerl an d
1 Scope and field of application IS0 1640, Wrought copper alloys - Forgings - Mechanical
properties. 2)
IS0 1635,
5 Forms of wrought products and mechanical
Wrought copper and copper alloys - Round tubes
properties
IS0 1637, Wrought copper and copper alloys - Rod and bar -
Mechanical properties. 2) The forms of wrought products in which these copper alloys
are available are given in table 2. The mechanical properties for
IS0 1638, Wrought copper and copper alloys - Wire - all forms of wrought products for which the symbol X is given,
Mechanical properties. 2) are defined in the following International Standards :
IS0 1639, Wrought copper alloys - Extruded profiles - IS0 16341 1, IS0 x34/2, IS0 1635, IS0 1637, IS0 1636,
Mechanical properties. 21 IS0 1639, IS0 1640.
Cu Zn 36Pb
Cu Zn 37PbZ
Cu Zn 36Pb3
Cu Zn 39Pb3
2
I n tern ati o n al Org an i z ati o n fo r S tan d ard i z ati o n
IS0 426/2-l = (E)
KEY :
(X) - form s m an u factu red i n sm al l er q u an ti ti es, for exam pl e i n certai n cou n tri es on l y or for speci al pu rposes.
NOTE - Wh ere n o sym bol i s g i ven , th e form i s n ot con si d ered of i m portan ce for th at type of copper al l oy, bu t i t d oes n ot n ecessari l y i n d i cate th at
Cu Zn 37PbZ X X 00 (X) X X
Cu Zn 36Pb3 X X 1 x1 X X (Xl
Cu Zn SPb2 X X X X X X X
Cu Zn 4OPbZ X X (Xl X X
Cu Zn 39Pb3 X X X X X
Cu Zn 38Pb4 X X X
Cu Zn 43Pb2 X
I I I I 1 I I