Beruflich Dokumente
Kultur Dokumente
Handset Application
Version 0.5
UART/HCI
▪ Platform BT IC
PCM
MTK BB
IC
MT6612
– Integrated LDO allows directly connect to VBAT. GPIO
▪ Applications
− Mobile Handset and Smartphone
− Portable Navigation Devices (PND)
− Laptop and Notebook
− Computer Peripherals
MT6612 Reference Design
OSC In EINT/GPIO
Dash line path is
only for AD6548 share clock
26MHz
MTK RF
VCXOEN
MT6612ForReference
MT6223,35,38,53…
Design – Power Protection
For MT6225
MT6612 MT5921
GPIO4 BT_ACT
50Ohm
Symmetrical and
Smaller than 2mm
Reference Layout (2/3)
▪ Power rail part:
– Low cost through-hole process can be adopted.
– Make star-connection at C23 for 2.8V power trace. Also, star-
connected at C51 for 1.2V trace route.
– Provide complete ground for power traces, do not route power traces
in parallel with or crossing to digital or strong disturbance signals.
C32
C23
1.2V C51
2.8V
Reference Layout (3/3)
▪ Digital part:
– The 32k trace MUST be shielded by ground along the routing. DO
NOT place any other trace along with it.
– 26MHz trace should be shielded by ground from BT to GSM BB and
RF when co-clock mechanism is employed. (detailed please refer to
MT6612 co-clock application note)
– DO NOT let strong disturbance signal trace across or parallel to BT
digital line, especially for BT_URXD3, BT_UTXD3, PCMCLK,
PCMSYNC, PCMIN, PCMOUT.
BT Antenna Design and Placement
▪ Place the BT antenna at the corner of the PCB.
▪ The feed point is directly connected to the antenna.
▪ Reserve enough distance between the antenna, ground and the shielding case.
▪ Ground blue screw holes, and don’t ground red screw holes.
Good
Feed point screw hole
Shielding case locations
> 3 mm
Bad
> 3 mm screw hole
locations
External Clock Sharing
MTK BT
SRCLKENA
1. Reserve pull-up and pull-down resistor on ECLKSEL pin to select external or X’tal
clock.
To BB SRCLKENAI and EINT
2. Connect SRCLKENA to BB’s SRCLKENAI and EINT/GPIO (please follow the table
for reference assignment)
Shared External Clock – AD6548 (2/3)
Assignment for Clock Indication (EINT/GPIO):
GPIO GPIO GPIO GPIO Edge/Level HW
EINT # BB Pin Pin Name IO Power
MODE 0 MODE 1 MODE 2 MODE 3 Trigger Debounce
EINT4 T3 GPIO0 VDD33 GPIO0 ---- ---- EINT4 Edge/Level Yes
EINT5 U4 GPIO1 VDD33 GPIO1 ---- ---- EINT5 Edge/Level Yes
MT6225
EINT6 T4 GPIO2 VDD33 GPIO2 ---- UCTS1 EINT6 Edge/Level Yes
EINT7 U5 GPIO3 VDD33 GPIO3 BSI_RFIN URTS1 EINT7 Edge/Level Yes
EINT2 C11 EINT2 VDD33 EINT2 GPIO42 ---- ---- Edge/Level Yes
EINT3 D11 EINT3 VDD33 EINT3 GPIO43 MIRQ ---- Edge/Level Yes
EINT4 R8 JTRST_B VDD33 JTRST_B GPIO26 EINT4 ---- Edge/Level Yes
MT6223 EINT5 P8 JTDI VDD33 JTDI GPIO27 EINT5 ---- Edge/Level Yes
EINT6 T9 JTMS VDD33 JTMS GPIO28 EINT6 ---- Edge/Level Yes
EINT7 U14 LCD_CS1_B VDD33_LCD LCD_CS1_B GPIO14 LCD_SCE1_B EINT7 Edge/Level Yes
MIRQ D11 EINT3 VDD33 EINT3 GPIO43 MIRQ ----
EINT3 E24 EINT3 VDD33 GPIO44 EINT3 DRF_DATA IRQ2 Edge/Level Yes
EINT4 E23 EINT4 VDD33 GPIO45 EINT4 DRF_EN CLKM3 Edge/Level Yes
MT6235 EINT5 D23 EINT5 VDD33 GPIO46 EINT5 EDICK ---- Edge/Level Yes
EINT6 D25 EINT6 VDD33 GPIO47 EINT6 EDIWS ---- Edge/Level Yes
EINT7 D24 EINT7 VDD33 GPIO48 EINT7 EDIDAT ---- Edge/Level Yes
EINT0 T16 EINT0 VDD33_NORM2 GPIO77 EINT0 CLKM4 ---- Edge/Level Yes
EINT1 AB17 EINT1 VDD33_NORM2 GPIO78 EINT1 CLKM5 ---- Edge/Level Yes
EINT2 AC19 EINT2 VDD33_NORM2 GPIO79 EINT2 DSP_GPO3 TBTXEN Edge/Level Yes
EINT3 AC25 EINT3 VDD33_NORM2 GPIO33 EINT3 DSP_GPO2 TBTXFS Edge/Level Yes
MT6238
EINT4 AD24 EINT4 VDD33_NORM2 GPIO34 EINT4 DSP_GPO1 TBRXEN Edge/Level Yes
EINT5 T17 EINT5 VDD33_NORM2 GPIO35 EINT5 DSP_GPO0 TBRXFS Edge/Level Yes
EINT6 AE18 EINT6 VDD33_NORM2 GPIO36 EINT6 EDIWS ---- Edge/Level Yes
EINT7 AC20 EINT7 VDD33_NORM2 GPIO37 EINT7 EDIDAT ---- Edge/Level Yes
Shared External Clock – AD6548 (3/3)
3. Please also reserve X’tal footprint for 4. In AD6548 26MHz output, reserve LPF
back-up. footprint and default use 0Ω connection.
MT6612
Clock buffer
To BB 26MHz
From AD6548 26MHz
PMU
Special Notes for AD6548 Co-clock Layout
MT6253 MT6612
6253 X’tal
SRCLKENA
To MT6253 SRCLKENAI
MT6253
To MT6612 26MHz
Special Notes for MT6253 Co-clock Layout
¾ Use Drv tool in Custom folder to configure GPIO, the clock request input should be
configured as SRCLKENAI mode.
Bluetooth Tool
▪ ATE tool
– Used for factory BT RF performance test.
– Support EDR RF test cases.
– Support instrument: R&S CMU/CBT, Anritsu 8852B and Agilent N4010A
Bluetooth Tool – ATE (2/2)
▪ Configure the test item in Customer_Setup.txt:
▪ BT Items = 1,1,1,1,1,0,0,0,0,0,0,1,1,1,1 Æ
– BT1.2 power, Initial Carrier Frequency, Carrier Frequency Drift, Modulation Character, Single Slot
BER,Multi Slot BER, EDR Relative Power, EDR Modulation Accuracy, EDR Differential Phase
Encoding, EDR Sensitivity, EDR BER floor, Reserve , Reserve , Reserve , Reserve
Bluetooth Tool – SN Writer
▪ SN Station
– Can write BD address (Meta mode)
– PCM Loop back 1 (Normal mode)
– PCM Loop back 2 (Normal mode)
Write BD address
2nd Source QVL
▪ Xtal
MT6612QFN X’tal Qualification List
Vendor PN F0 (MHz) Cload (pF) Dimensions (mm)
射 频 和 天 线 设 计 培 训 课 程 推 荐
易迪拓培训(www.edatop.com)由数名来自于研发第一线的资深工程师发起成立,致力并专注于微
波、射频、天线设计研发人才的培养;我们于 2006 年整合合并微波 EDA 网(www.mweda.com),现
已发展成为国内最大的微波射频和天线设计人才培养基地,成功推出多套微波射频以及天线设计经典
培训课程和 ADS、HFSS 等专业软件使用培训课程,广受客户好评;并先后与人民邮电出版社、电子
工业出版社合作出版了多本专业图书,帮助数万名工程师提升了专业技术能力。客户遍布中兴通讯、
研通高频、埃威航电、国人通信等多家国内知名公司,以及台湾工业技术研究院、永业科技、全一电
子等多家台湾地区企业。
易迪拓培训推荐课程列表: http://www.edatop.com/peixun/tuijian/
射频工程师养成培训课程套装
该套装精选了射频专业基础培训课程、射频仿真设计培训课程和射频电
路测量培训课程三个类别共 30 门视频培训课程和 3 本图书教材;旨在
引领学员全面学习一个射频工程师需要熟悉、理解和掌握的专业知识和
研发设计能力。通过套装的学习,能够让学员完全达到和胜任一个合格
的射频工程师的要求…
课程网址:http://www.edatop.com/peixun/rfe/110.html
手机天线设计培训视频课程
该套课程全面讲授了当前手机天线相关设计技术,内容涵盖了早期的
外置螺旋手机天线设计,最常用的几种手机内置天线类型——如
monopole 天线、PIFA 天线、Loop 天线和 FICA 天线的设计,以及当前
高端智能手机中较常用的金属边框和全金属外壳手机天线的设计;通
过该套课程的学习,可以帮助您快速、全面、系统地学习、了解和掌
握各种类型的手机天线设计,以及天线及其匹配电路的设计和调试...
课程网址: http://www.edatop.com/peixun/antenna/133.html
WiFi 和蓝牙天线设计培训课程
课程网址:http://www.edatop.com/peixun/antenna/134.html
`
专注于微波、射频、天线设计人才的培养
易迪拓培训 网址:http://www.edatop.com
CST 学习培训课程套装
HFSS 学习培训课程套装
ADS 学习培训课程套装
我们的课程优势:
※ 成立于 2004 年,10 多年丰富的行业经验,
※ 一直致力并专注于微波射频和天线设计工程师的培养,更了解该行业对人才的要求
※ 经验丰富的一线资深工程师讲授,结合实际工程案例,直观、实用、易学
联系我们:
※ 易迪拓培训官网:http://www.edatop.com
※ 微波 EDA 网:http://www.mweda.com
※ 官方淘宝店:http://shop36920890.taobao.com
专注于微波、射频、天线设计人才的培养
易迪拓培训 官方网址:http://www.edatop.com
淘宝网店:http://shop36920890.taobao.com