Beruflich Dokumente
Kultur Dokumente
2. Revolve steadily under very low speed due to high starting torque
and good low-speed stability;
3. Good reliability and less leakage due to the patented flat compensation distributor, special sealing between
piston and plunger bushing guarantees higher volumetrical effvciency;
25-35
4. High mechanical efficency due to roller bearing between crankshaft and connecting rod;
5. Reversible rotation, and the output shaft can bear certain extermal force from both radial and axial diredtions;
6. High power-mass ratio, small volume and light weight.
4. I-inside spline (the center is up to interior diameter); footnote number means the
installation dimension is the same as QJM series of motors produced by Ningbo
Hydraulic Motor Factory (with flange).
1.Filtration: the recommended filtration precision for normal industrial use is 25μm, and allowable precision
low pressure, low speed or intervall is 75μm.
2. Oil viscosity: the optimum performance could only be obtained under proper oil viscosity between 15-1000cst.
3. Before the first start-up, it must fill hydraulic oil in the hydraulic motor body, to avoid the damage.
4. Leakage: drain port should be connected separately to the tank. Normally the maximum pressure for the motor
body is 0.1 Mpa, and it could also be improved to bear 3-5 Mpa, to meet special requirements.
5. The top line of the drain pipe should be higher than that of the motor body, in case empting oil storage.
6. Installation: motor can be installed in any position with rigid support, When installed, shafts of the motor
and its transmission should be concentric. "Left deviation" and "Right deviation" are only applicable for NHM2-NHM11 series of motors, and oil inlet and outlet
7. Cleanness: Strictly maintain the cleanness of the oil port, and keep any solid particles away. are horizontal. (Same as illustrated)
8. Release both the radial and axial loads of the output shaft to enable longer life of the motor.
9. NHM motor could not work as a pump.
01 02
NINGBO OIL CONTROL HYDRAULIC CO.,LTD. DRIVE & CONTROL
NHM SERIES HYDRAULIC MOTORS
Uniform
distribution
Mounting Surface of mounting holes
均布
244
Oil drain port
Uniform distribution
of mounting holes
Mounting Surface
Mounting Surface
Mounting Surface
32
03 04
NINGBO OIL CONTROL HYDRAULIC CO.,LTD. DRIVE & CONTROL
NHM SERIES HYDRAULIC MOTORS
255
of mounting
distribution
of mounting
of mounting
distribution
distribution
Uniform
Uniform
Uniform
Oil drain port
holes
holes
holes
Standard outside spline Standard parallel key Standard inside spline
of mounting
of mounting
mounting holes
distribution
distribution
Uniform
Uniform
holes
holes
Mounting Surface
Mounting Surface Mounting Surface
of mounting
distribution
Uniform
holes
of mounting
distribution
of mounting
distribution
Uniform
Ð º
Uniform
holes
holes
05 06
NINGBO OIL CONTROL HYDRAULIC CO.,LTD. DRIVE & CONTROL
NHM SERIES HYDRAULIC MOTORS
Mounting
Surface
Mounting Mounting
Uniform Surface
Mounting Surface Surface
distribution
of mounting holes
of mounting
distribution
of mounting
distribution
of mounting
distribution
Uniform
Uniform
Uniform
Oil drain port
holes
holes
holes
Standard outside spline Standard parallel key Standard inside spline
Mounting Surface
Mounting Mounting
Mounting Surface Mounting Surface
Mounting Surface Surface Surface
of mounting
of mounting
distribution
distribution
Spline key shaft
Uniform
Uniform
holes
holes
Mounting Surface Mounting Surface
Mounting Surface
of mounting
distribution
of mounting
distribution
Uniform
Uniform
holes
holes
07 08
NINGBO OIL CONTROL HYDRAULIC CO.,LTD. DRIVE & CONTROL
NHM SERIES HYDRAULIC MOTORS
Mounting Mounting
Mounting Surface Surface
Mounting
Surface Uniform Surface
distribution
of mounting
holes
of mounting
distribution
Mounting
of mounting
distribution
Uniform
holes
Uniform
holes
holes
Oil drain port
of mounting
distribution
of mounting
distribution
Uniform
holes
Uniform
holes
Mounting Mounting
Mounting Surface Mounting Surface
Mounting Surface Surface
Surface
of mounting
distribution
of mounting
distribution
of mounting
distribution
Uniform
Mounting
Uniform
holes
Uniform
holes
holes
Mounting
holes
holes
09 10
NINGBO OIL CONTROL HYDRAULIC CO.,LTD. DRIVE & CONTROL
NHM SERIES HYDRAULIC MOTORS
Uniform
distribution
Mounting of mounting Uniform
Mounting
Surface holes distribution
Surface
of mounting
holes
Standard outside spline Standard parallel key parallel shaft Standard outside spline Standard parallel key Standard inside spline
Mounting
Mounting Mounting Surface
Mounting Mounting Surface Surface
Mounting
Surface Surface Surface
Uniform distribution
of mounting holes
of mounting holes
of mounting holes
of mounting
distribution
of mounting
of mounting
Uniform
distribution
distribution
holes
Uniform
Uniform
holes
holes
11 12
NINGBO OIL CONTROL HYDRAULIC CO.,LTD. DRIVE & CONTROL
NHM SERIES HYDRAULIC MOTORS
Mounting
Mounting Mounting Surface Uniform
Mounting Surface Surface distribution
Surface
of mounting
holes
Depth
of mounting
of mounting
distribution
distribution
of mounting
Uniform
Uniform
Uniform
holes
holes
holes
Mounting
Mounting Mounting Mounting Mounting Mounting
Surface
Surface Surface Surface Surface Surface
of mounting
distribution
of mounting
distribution
Uniform
Uniform
of mounting
distribution
holes
holes
Uniform
holes
Mounting Mounting
Surface Mounting
Surface
Surface
Mounting Mounting
Surface Mounting
Surface
Surface
of mounting
distribution
of mounting
distribution
of mounting
distribution
Uniform
Uniform
Uniform
holes
holes
holes
of mounting
of mounting
distribution
distribution
Mounting
Uniform
Uniform
holes
holes
holes
13 14
NINGBO OIL CONTROL HYDRAULIC CO.,LTD. DRIVE & CONTROL
NHM SERIES HYDRAULIC MOTORS
Mounting
Surface Uniform
distribution
Mounting Mounting of mounting
Mounting Surface Surface holes
Surface
Depth
of mounting
distribution
of mounting
distribution
Uniform
holes
Uniform
holes
Mounting
of mounting
distribution
holes
Uniform
holes
Mounting Mounting
Surface Mounting
Surface Surface
Mounting
Surface
of mounting
distribution
of mounting
distribution
Uniform
Uniform
holes
holes
Mounting
holes
15 16
NINGBO OIL CONTROL HYDRAULIC CO.,LTD. DRIVE & CONTROL
NHM SERIES HYDRAULIC MOTORS
Uniform
distribution
Mounting of mounting
Surface holes
Mounting
Mounting Surface
Surface
Mounting
Surface
Depth
of mounting
distribution
of mounting
distribution
Uniform
Uniform
holes
holes
Standard parallel key
Mounting Mounting
Surface Mounting Surface
Mounting Surface
Surface Mounting
Mounting Uniform Surface
Surface distribution
of mounting
holes
of mounting
distribution
Uniform
holes
Standard parallel key
Mounting
holes
Mounting
Mounting
holes
of mounting
distribution
Uniform
of mounting
distribution
holes
Uniform
holes
17 18