Beruflich Dokumente
Kultur Dokumente
Rev. 1
March, 2011
Charge Manual – Peugeot 307 2
SUMMARY
Introduction ..............................................................................Page 3
Used Accessories.....................................................................Page 4
Key Programming....................................................................Page11
Other messages.......................................................................Page14
Charge Manual – Peugeot 307 3
Introduction
With this charge it’s possible to achieve the following functions:
Vehicle: Vehicle:
Brand: Peugeot Brand: Citroën
Model: 307 Model: C4 and C4 Pallas
Year: 2007 to 2009 Year: 2007 to 2010
With this charge it’s possible to program utmost 5 keys at the same time
in the same vehicle.
The immobilizer system works with theT-19 transponder or ID46 crypto
without lock.
The remote controls and the programmed Keys not presented, Will not
work in this vehicle, therefore, have in hands all the remote controls and keys
to be programmed.
Back to Summary
Charge Manual – Peugeot 307 4
Used Accessories:
Back to Summary
Charge Manual – Peugeot 307 5
Area B
Area A
Area B
5
Back to Summary
Charge Manual – Peugeot 307 6
Attention
First of all weld the wires to the BSI, and then connect MCU to the OBDMap.
The wires that are not being used must be bent backwards as shown in
the picture, that way not having any contact with the BSI and avoiding
damages to the BSI and to the OBDMap.
Back to Summary
Charge Manual – Peugeot 307 8
STEP 1
Select:
Press OK
Clip
Select:
STEP 2 Tecle OK
Peugeot
STEP 3
Select:
Press OK
BSI PEUGEOT 307
Wait...
STEP 6
PIN code: Note the PIN
**** code. Press OK
Back to Summary
Charge Manual – Peugeot 307 9
Diagnosis socket
located.
Charge Manual – Peugeot 307 10
Back to Summary
índice
Charge Manual – Peugeot 307 11
Key programming:
After connecting all accessories to the vehicle, follow the steps displayed in the
OBDMap screen.
STEP 1
Select:
Press OK
Diagnosis
STEP 2
Select:
Press OK
Peugeot
STEP 3
Select:
Press OK
307
STEP 4 307
Press OK
Programming?
This message appears
Use the Uni. only if the universal cable
STEP 5
cable + A4 adap. + A4 is not connected to
the OBDMap.
Using
Transponder:ID46
STEP 6 Press OK
Turn On Ignition
and press OK
e tecle OK
BSI PIN code: Put the previous read
STEP 7
**** PIN code. Press OK.
Key nº 1
programmed
STEP 11 Press OK
Remove the key
and press OK
Key nº2
programmed
STEP 13 Press OK
Remove the key
and press OK
Programming
concluded!
Back to Summary
Charge Manual – Peugeot 307 13
Telecontrol programming:
Attention: Every time you finish the key programming procedure DON’T
Turn On ignition and press ANY button of the remote control in a minute.
LOCK
Buttom.
Remove the key from the ignition and press LOCK, the locking devices
of the vehicle will be achieved this way confirming the remote control
programming.
Back to Summary
Charge Manual – Peugeot 307 14
Other Messages:
Error in
The OBDMap could not read the BSI data.
Reading!
Probable causes:
Bad contact in the MCU cable to the BSI,
Bad contact in the MCU cable to the OBDMap,
BSI damaged of corrupted file.
Solution:
Check the correct positions of the wires in the BSI,
Check if the screws that fix the MCU cable to the OBDMap are well fixed,
Check if the MCU cable presents any visible defect, if presents send it to repair.
Short Circuit!
It was detected a short circuit in the MCU cable.
Check...
Probable causes:
The wires have been welded in other spots of the BSI,
The MCU cable or BSI is damaged.
Solution:
Check the correct position of the wires of the BSI,
Check if the MCU cable presents any visible defect, if presents send it to repair.
Charge Manual – Peugeot 307 15
Solution:
Typing the correct PIN code.
Remark: After typed three times the incorrect PIN code, the BSI locks for 15
minutes, not being possible to achieve the procedure even typing the correct PIN
code.
Probable Causes:
Defective vehicle, defective electrical part,
Expired update of the OBDMap,
OBDMap is damaged, cables of equipment.
Solution:
Check the electric part of the vehicle, fuses, etc,
Check if universal cable and A4 adapter is being used,
Check the good connection of the cable to the OBDMap and in the OBD
connector of the vehicle,
Check the status of the universal cable and A4 adapter,
Check for recently updates with the technical support, maybe the charge has
been altered.
Back to Summary