Beruflich Dokumente
Kultur Dokumente
hqseng@xxx
pass Telkomsel01
Dear All,
Status : Done
Result : Alarm Clear at SP.TDC.SOE.1 ,
Alarm module still appear at SP.TDC.SOE.2 (Need RMA), All spine traffic maintain
Punten
Mas Dian mohon approval untuk yang ini sepertinya belum Mas...
1. CRQ000000672653 - Troublsehoot ILOM SOE1 & ILOM DGO1
Hatur nuhun
PIC :
Punten
Mas Dian mohon approval untuk yang ini sepertinya belum Mas...
1. CRQ000000672653 - Troublsehoot ILOM SOE1 & ILOM DGO1
Hatur nuhun
Detail Activity :
1. Configure parameter Time and NTP Server for ILOM SOE1
2. Troubleshoot PEM ILOM DGO1 :
Step 1. make sure MCB switch is on
Step 2. if point 1 ok, make sure cable from APCDB to DCPD is ok
Step 3. if point 2 ok, tracing cable from DCPDB to ILOM.DGO1 Device make sure cable
is ok
Step 4. if point 3 ok, plug & unplug PEM Modul on ILOM.DGO1
=============================
- Evidence show hardware Thermal pas kejadian (kan dy nya ambil log, klo emang
diisukan overtemp)
- Untuk filter 4 ggsn udah dibersihkan dan thermal imaging gak ada suhu ekstrim
(20-30 an) pas kejadian
- Usulan Sinkronisasi Module2 yang terpasang di Bandung (xx/3) module baru dan
ketersediaan di sparepool Bandung (RPSW kmaren dari Sumatra)
- Mekanisme user Tacacs untuk percepatan tshoot klo perlu reload or config (clear
BGP) (lepas cable ke arah management Port, namun user Local Ericsson masih
downgrade)
- After problem minimal ada orang Ericsson yang monitor traffic and payload per xx
jam selama 1-2 hari
- dari 3 Case kmaren kan d dahuluin module RPSW dan ALSW yang fail switchover,
why ??
- PDP & Bearer GGSN, throughput 4G gak balance after case, ada mekanisme
balancing ?
Detail Activity :
1. Configure parameter Time and NTP Server for ILOM SOE1
2. Troubleshoot PEM ILOM DGO1 :
Step 1. make sure MCB switch is on
Step 2. if point 1 ok, make sure cable from APCDB to DCPD is ok
Step 3. if point 2 ok, tracing cable from DCPDB to ILOM.DGO1 Device make sure cable
is ok
Step 4. if point 3 ok, plug & unplug PEM Modul on ILOM.DGO1
Bismillahirrohmanirrahim...
Detail ACtivity :
1. Configure parameter Time and NTP Server for ILOM SOE1
2. Troubleshoot PEM ILOM DGO1 :
Step 1. make sure MCB switch is on
Step 2. if point 1 ok, make sure cable from APCDB to DCPD is ok
Step 3. if point 2 ok, tracing cable from DCPDB to ILOM.DGO1 Device make sure cable
is ok
Step 4. if point 3 ok, plug & unplug PEM Modul on ILOM.DGO1s
Status : Plan
Result : -
PIC :
Bang Dian...
Mohon approval Work Order CRQ000000673290 - Troubleshoot SHMU-2 at XBDG6 plan besok
malam...
Hatur nuhun...
Detail Activity :
1. Take Log and configuration before
2. Replace Module SHMU-2
3. Update SHMC and FRU
4. Take Log and configuration After
Bismillahirrohmanirrahim...
Detail Activity :
1. Take Log and configuration before
2. Replace Module SHMU-2 (fail, need config by Nokia)
3. Unplug Plug Module SHMU-2 - Restart Module SHMU-2
4. Test Switchover module SHMU-2 OK
Impact Service : No Service Impact
Status : Done
Result : Module SHMU-2 Working Normal
PIC :
Bang Dian...
Punten mohon approval CRQ : CRQ000000673032 - Troubleshoot Signaling point Code
From RNC DAGO 3 to SGSN (28/01/2020)...
Hatur nuhun...
Detail Activity :