Beruflich Dokumente
Kultur Dokumente
and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd.
All other trademarks and trade names mentioned in this document are the property of their respective
holders.
Notice
The purchased products, services and features are stipulated by the contract made between Huawei and the
customer. All or part of the products, services and features described in this document may not be within the
purchase scope or the usage scope. Unless otherwise specified in the contract, all statements, information,
and recommendations in this document are provided "AS IS" without warranties, guarantees or
representations of any kind, either express or implied.
The information in this document is subject to change without notice. Every effort has been made in the
preparation of this document to ensure accuracy of the contents, but all statements, information, and
recommendations in this document do not constitute a warranty of any kind, express or implied.
Website: http://www.huawei.com
Email: support@huawei.com
Contents
1 Change History.............................................................................................................................. 1
1.1 eRAN13.1 05 (2019-04-30)............................................................................................................................................1
1.2 eRAN13.1 04 (2019-01-21)............................................................................................................................................1
1.3 eRAN13.1 03 (2018-11-12)............................................................................................................................................2
1.4 eRAN13.1 02 (2018-06-30)............................................................................................................................................2
1.5 eRAN13.1 01 (2018-04-10)............................................................................................................................................3
1.6 eRAN13.1 Draft B (2018-03-30)....................................................................................................................................3
1.7 eRAN13.1 Draft A (2018-01-15) (FDD)........................................................................................................................4
5 Coverage-based Handover.........................................................................................................55
5.1 Overview...................................................................................................................................................................... 55
5.1.1 Introduction to Handover Functions..........................................................................................................................55
5.1.2 Measurement-based Handover Functions................................................................................................................. 55
5.1.3 Blind Handover Functions.........................................................................................................................................56
5.1.4 Event A2 Involved in Coverage-based Handover..................................................................................................... 57
5.1.5 Principles for Selecting UTRAN or GERAN for Inter-RAT Handovers.................................................................. 59
5.2 Coverage-based Intra-frequency Handover..................................................................................................................60
5.2.1 Principles................................................................................................................................................................... 60
5.2.2 Network Analysis...................................................................................................................................................... 61
5.2.2.1 Benefits................................................................................................................................................................... 61
5.2.2.2 Impacts....................................................................................................................................................................62
5.2.3 Requirements............................................................................................................................................................. 62
5.2.3.1 Licenses.................................................................................................................................................................. 62
5.2.3.2 Software..................................................................................................................................................................62
5.2.3.3 Hardware................................................................................................................................................................ 62
5.2.3.4 Others......................................................................................................................................................................63
5.2.4 Operation and Maintenance.......................................................................................................................................63
5.2.4.1 Data Configuration................................................................................................................................................. 63
5.2.4.1.1 Data Preparation.................................................................................................................................................. 63
5.2.4.1.2 Using MML Commands...................................................................................................................................... 63
5.2.4.1.3 Using the CME.................................................................................................................................................... 63
5.2.4.2 Activation Verification........................................................................................................................................... 64
5.2.4.3 Network Monitoring............................................................................................................................................... 64
5.3 Coverage-based Inter-frequency Handover.................................................................................................................. 64
5.3.1 Principles................................................................................................................................................................... 64
5.3.1.1 Initiation Decision of Measurement-based Handover............................................................................................ 66
5.3.1.1.1 Event A2.............................................................................................................................................................. 70
5.3.1.1.2 Event A1.............................................................................................................................................................. 73
5.3.1.2 Measurement Configuration Delivery.................................................................................................................... 73
5.3.1.3 Target Cell Decision for Measurement-based Handover........................................................................................75
5.3.1.3.1 Event A3.............................................................................................................................................................. 75
5.3.1.3.2 Event A4.............................................................................................................................................................. 75
5.3.1.3.3 Event A5.............................................................................................................................................................. 76
5.3.1.4 Principles of Blind Handover Functions................................................................................................................ 76
5.3.1.4.1 Preferential Blind Handover................................................................................................................................ 77
5.3.1.4.2 Emergency Blind Handover................................................................................................................................ 77
5.3.2 Network Analysis...................................................................................................................................................... 79
5.3.2.1 Benefits................................................................................................................................................................... 79
5.3.2.2 Impacts....................................................................................................................................................................79
5.3.3 Requirements............................................................................................................................................................. 79
5.3.3.1 Licenses.................................................................................................................................................................. 80
5.3.3.2 Software..................................................................................................................................................................80
5.3.3.3 Hardware................................................................................................................................................................ 80
5.3.3.4 Others......................................................................................................................................................................80
5.3.4 Operation and Maintenance.......................................................................................................................................80
5.3.4.1 Data Configuration................................................................................................................................................. 80
5.3.4.1.1 Data Preparation.................................................................................................................................................. 80
5.3.4.1.2 Using MML Commands...................................................................................................................................... 86
5.3.4.1.3 Using the CME.................................................................................................................................................... 86
5.3.4.2 Activation Verification........................................................................................................................................... 87
5.3.4.3 Network Monitoring............................................................................................................................................... 87
5.4 Coverage-based Inter-RAT Handover to UTRAN....................................................................................................... 88
5.4.1 Principles................................................................................................................................................................... 88
5.4.1.1 Initiation Decision of Measurement-based Handover............................................................................................ 90
5.4.1.1.1 Event A2.............................................................................................................................................................. 92
5.4.1.1.2 Event A1.............................................................................................................................................................. 94
6 Service-based Handover...........................................................................................................116
6.1 Overview.....................................................................................................................................................................116
6.2 Service-based Inter-frequency Handover................................................................................................................... 117
6.2.1 Principles................................................................................................................................................................. 117
6.2.1.1 Handover Function Initiation Decision.................................................................................................................118
6.2.1.2 Measurement Configuration Delivery.................................................................................................................. 118
6.2.1.3 Target Cell Determination.....................................................................................................................................118
6.2.2 Network Analysis.................................................................................................................................................... 119
6.2.2.1 Benefits................................................................................................................................................................. 119
6.2.2.2 Impacts..................................................................................................................................................................119
6.2.3 Requirements........................................................................................................................................................... 120
6.2.3.1 Licenses................................................................................................................................................................ 120
6.2.3.2 Software................................................................................................................................................................120
6.2.3.3 Hardware.............................................................................................................................................................. 121
6.2.3.4 Others....................................................................................................................................................................121
6.2.4 Operation and Maintenance.....................................................................................................................................121
6.2.4.1 Data Configuration............................................................................................................................................... 121
6.2.4.1.1 Data Preparation................................................................................................................................................ 121
6.2.4.1.2 Using MML Commands.................................................................................................................................... 122
6.2.4.1.3 Using the CME.................................................................................................................................................. 123
6.2.4.2 Activation Verification......................................................................................................................................... 123
6.2.4.3 Network Monitoring............................................................................................................................................. 124
6.3 Service-based Inter-RAT Handover to UTRAN.........................................................................................................124
6.3.1 Principles................................................................................................................................................................. 124
6.3.1.1 Handover Function Initiation Determination....................................................................................................... 125
6.3.1.2 Target Cell Determination.................................................................................................................................... 126
6.3.2 Network Analysis.................................................................................................................................................... 126
6.3.2.1 Benefits................................................................................................................................................................. 126
6.3.2.2 Impacts..................................................................................................................................................................126
6.3.3 Requirements........................................................................................................................................................... 126
13 Parameters................................................................................................................................. 202
14 Counters.................................................................................................................................... 435
15 Glossary..................................................................................................................................... 777
16 Reference Documents............................................................................................................. 778
1 Change History
This chapter describes changes not included in the "Parameters", "Counters", "Glossary", and
"Reference Documents" chapters. These changes include:
l Technical changes
Changes in functions and their corresponding parameters
l Editorial changes
Improvements or revisions to the documentation
Technical Changes
None
Editorial Changes
Changed the QCI values in the MML command examples. For details, see 4.4.1.2 Using
MML Commands, 6.3.4.1.2 Using MML Commands, and 6.4.4.1.2 Using MML
Commands.
Added descriptions about not recommending service-based inter-RAT handovers for QCI 1
services. For details, see 6.3.1.1 Handover Function Initiation Determination.
Added configuration constraints on the target frequencies for the QCI with the highest priority
in service-based inter-frequency handovers. For details, see 6.2.1.2 Measurement
Configuration Delivery.
Technical Changes
None
Editorial Changes
Added the description about the UTRAN frequency to be contained in the delivered
measurement configurations. For details, see 5.4.1.2 Measurement Configuration Delivery.
Added the description about how the eNodeB determines whether to enable service-based
inter-RAT handover to UTRAN for a UE. For details, see 6.3.1.1 Handover Function
Initiation Determination.
Added other parameters related to event A5. For details, see 4.1.4.2.3 Other Parameters.
Changed the value of the GERAN version parameter in the MML command for adding the
neighbor relationship with a GERAN cell. For details, see 4.4.1.2 Using MML Commands.
Revised the descriptions of capabilities of handovers to the UTRAN and GERAN. For details,
see 4.1.6.2.3 Inter-RAT Handover Policy.
Technical Changes
None
Editorial Changes
Modified the description about how eNodeB acts when another gap pattern needs to be set up
during the gap-assisted measurement. For details, see 4.1.4.3 Other Configurations.
Added descriptions about intra-RAT handovers. For details, see 4.1.7 Handover Execution.
Technical Changes
Change Description Parameter Change RA Base Station
T Model
Editorial Changes
Revised descriptions in this document.
Technical Changes
None
Editorial Changes
Revised descriptions in this document.
Technical Changes
None
Editorial Changes
Deleted descriptions of the speed-based inter-frequency handover (FDD).
Added deactivation command examples. For details, see the respective "Using MML
Commands" sections.
Technical Changes
Change Description Parameter Change Base Station Model
Editorial Changes
l Combined Overview of Mobility Management in Connected Mode, Intra-RAT Mobility
Management in Connected Mode, and Inter-RAT Mobility Management in Connected
Mode.
l Reorganized this document using a new template.
Handover in this document is a generic term that covers procedures related to mobility management in
connected mode.
In the case of handover policy, handover is a specific term in contrast to redirection. In this case,
handover refers to a procedure in which the serving cell of a UE changes. For details, see 4.1.6.2.1
Handover Policies.
This document focuses on the common process of mobility management in connected mode
for data services. For details about intra-RAT mobility management in connected mode for
voice over Long Term Evolution (VoLTE) services, see VoLTE. For details about inter-RAT
mobility management in connected mode to UTRAN or GERAN for VoLTE services, see
SRVCC. For details about inter-RAT mobility management in connected mode to UTRAN or
GERAN for non-VoLTE voice services, see CS Fallback. The mobility management
mechanism of combined services varies depending on the service with the highest-priority
QCI.
Load-based When a cell is heavily loaded but its neighboring cells are lightly
handover loaded, the eNodeB initiates load-based handovers from the
overloaded cell to maximize system resource usage.
For details about load-based handovers, including intra-RAT and
inter-RAT handovers, see Intra-RAT Mobility Load Balancing and
Inter-RAT Mobility Load Balancing, respectively.
Service-based When operators require that services with different QCIs be carried
handover by different frequencies, service-based handovers can be used to
preferentially set up services with specified QCIs on specified
frequencies for service steering.
UL-quality-based When the uplink signal quality is poor but the downlink signal
handover quality is normal, the eNodeB promptly initiates a UL-quality-based
handover to prevent service drops caused by poor uplink signal
quality.
Frequency- When a network has both low and high bands, the eNodeB initiates
priority-based frequency-priority-based handovers so that UE services can be
handover preferentially carried on the high band and the low band is spared for
contiguous coverage.
Other handoversa The following lists mobility management policies for other services
or scenarios and their reference documents:
l VoLTE-specific handovers. For details, see VoLTE.
l Video-specific handovers, such as QoE-based handovers from E-
UTRAN to UTRAN. For details, see UL Unified Video Steering.
l Inter-frequency handovers for primary component carrier (PCC)
anchoring. For details, see Carrier Aggregation.
l Inter-frequency handovers based on evolved multimedia
broadcast/multicast service (eMBMS) service interest indications.
For details, see eMBMS.
l Handover enhancement at high speed mobility. For details, see
High Speed Mobility.
l UE-specific handovers, such as SPID-based handovers back to
home public land mobile network (HPLMN). For details, see
Flexible User Steering.
l Inter-RAT handovers of CS services and handovers of PS services
to CDMA2000 networks. For details about CS service handovers
to UTRAN and GERAN, see VoLTE, SRVCC, and CS Fallback.
For details about handovers to CDMA2000 networks, see LTE-
CDMA2000 CS Service Interworking (FDD), and LTE-
CDMA2000 PS Service Interworking.
The basic procedures for handover functions are the same. For details, see 4 Basic Functions
of Mobility Management in Connected Mode. The differences between handover functions
are described in their respective sections. Users can read 4 Basic Functions of Mobility
Management in Connected Mode and the corresponding handover function section to
acquire complete information about a handover function.
Table 3-2 briefs the differences among handover functions.
Distance- The distance between The distance between the UE For intra-frequency handovers:
based the UE and the and the eNodeB falls below N/A
handover eNodeB exceeds a the specified threshold. For inter-frequency handovers:
configured value. event A4
For inter-RAT handovers: event B1
or B2
Service- The eNodeB receives a Measurement has been Event A4 (This handover function
request-based UE's service setup or performed for a time specified involves only inter-frequency
handover modification request. by handovers.)
ServiceIfHoCfgGroup.A4Rp
tWaitingTimer, but no
measurement report is
received.
a: These handovers can be processed in measurement-based mode or blind mode. Handovers not marked with a
can be processed only in measurement-based mode. For details about handover processing modes, see 4.1.3
Processing Mode Selection.
b: For details about the events in this table, see 4.1.4.2.1 Measurement Events.
c: Handover execution initiation conditions are involved only in measurement-based mode, not in blind mode.
4.1 Principles
The conditions for determining whether a UE in its serving cell requires a handover vary
depending on handover functions. The conditions are described in follow-up chapters
and sections related to handover functions.
l 4.1.3 Processing Mode Selection describes blind mode and measurement-based mode,
which differ in whether to measure cells.
l 4.1.4 Measurement Configuration Delivery describes delivery of measurement
configurations to the UE. This procedure applies only to measurement-based mode.
l 4.1.5 Measurement Reporting describes reporting of measurement results to the
eNodeB. This procedure applies only to measurement-based mode.
l 4.1.6 Target Cell or Frequency Decision describes how the eNodeB selects a target cell
or target frequency after a handover function is initiated. In this procedure, the eNodeB
determines whether there is a suitable new serving cell for the handover. If there is, the
eNodeB starts executing the handover.
l 4.1.7 Handover Execution describes handover preparation and execution.
l 4.1.8 Retry and Penalty for Handover Failures describes penalty and retry after the
handover fails.
Measurement objects can be the serving cell or neighboring cells. The procedures for
measuring the serving cell and neighboring cells are the same. This section uses neighboring
cell measurement as an example to describe measurement configuration delivery.
After a radio bearer is established for the UE, the eNodeB includes measurement
configurations in an RRC Connection Reconfiguration message and delivers the message to
the UE based on handover function configurations.
The eNodeB also checks whether the measurement configurations for the UE need to be
updated after the UE enters the RRC_CONNECTED mode or a handover is completed. If it
does, the eNodeB delivers updated measurement configurations to the UE in an RRC
Connection Reconfiguration message.
Measurement configurations are mainly determined on the eNodeB side and are delivered to
UEs, which include the following information about measurement tasks:
l Measurement objects
Measurement objects include the RATs, frequencies, and cells whose signal quality
needs to be measured.
l Reporting configurations
Reporting configurations include measurement event information, triggering quantity
and reporting quantity (only for intra-RAT handovers), and other information about
measurement reports. Reporting configurations specify the criteria for measurement
reporting.
l Other configurations
Other configurations include measurement quantity, measurement gap, and measurement
filtering coefficient.
RAT Configuration
Measurement-based UtranNFreq.ConnFreqPriority
handover from E-
UTRAN to UTRAN
Measurement-based GeranNfreqGroup.ConnFreqPriority
handover from E-
UTRAN to GERAN
The total number of target frequencies included in measurement configurations of all RATs
must not exceed the total number of inter-frequency and inter-RAT measurement objects,
which is specified by the CellUeMeasControlCfg.MaxNonIntraMeasObjNum parameter. In
GERAN, a frequency group is delivered as one measurement object. A frequency group
contains a maximum of 32 frequencies.
Neighboring E-UTRAN FDD and TDD frequency configurations are set in the
EUTRANINTERNFREQ MO. When the main control board is UMPT, a maximum of 16
neighboring FDD and TDD frequencies can be configured. When another main control board
is used, a maximum of eight neighboring FDD and TDD frequencies can be configured.
l For E-UTRAN FDD, the maximum number of frequencies that can be delivered in
measurement configurations is the smaller value between the
CellUeMeasControlCfg.MaxEutranFddMeasFreqNum parameter value and the
number of configured neighboring FDD frequencies.
l For E-UTRAN TDD, the maximum number of frequencies that can be delivered in
measurement configurations is the smaller value between the
CellUeMeasControlCfg.MaxEutranTddMeasFreqNum parameter value and the
number of configured neighboring TDD frequencies.
Table 4-3 Parameters that specify the maximum number of frequencies of each RAT
RAT Parameter Specifying the Maximum Number of Frequencies that
Can Be Delivered in Measurement Configurations
E-UTRAN CellUeMeasControlCfg.MaxEutranFddMeasFreqNum
FDD
E-UTRAN CellUeMeasControlCfg.MaxEutranTddMeasFreqNum
TDD
UTRAN CellUeMeasControlCfg.MaxUtranFddMeasFreqNum
FDD
UTRAN CellUeMeasControlCfg.MaxUtranTddMeasFreqNum
TDD
GERAN CellUeMeasControlCfg.MaxGeranMeasFreqNum
NOTE
If the sum of the number of to-be-delivered GERAN frequencies in the highest-priority GERAN
frequency group and the number of delivered GERAN frequencies exceeds the maximum number of
GERAN frequencies allowed for measurement, all the GERAN frequencies in this GERAN frequency
group are not delivered in measurement configurations. The eNodeB evaluates the frequency group with
the next highest priority till the number of delivered frequencies equals the maximum number of
GERAN frequencies allowed for measurement or all frequency groups are evaluated.
Measurement Preemption
According to 3GPP TS 36.133, UE capability in gap-assisted inter-frequency or inter-RAT
measurements is limited. Measurement preemption allows a UE with such a limited capability
to measure higher-priority frequencies when possible.
The MEAS_OBJ_PREEMPT_SW option of the CellAlgoSwitch.MeasOptAlgoSwitch
parameter specifies whether to enable this function. If this option is selected and the UE
frequency measurement capability is limited, the eNodeB checks whether the priority of the
algorithm to be started is higher than the highest priority of earlier started algorithms. If the
priority of the algorithm to be started is higher, the eNodeB enables this algorithm to preempt
measurement resources, which means that the UE measures the frequency involved in the
algorithm to be started. Table 4-4 lists the algorithm priorities for frequency measurement.
For details, see section 6.3.5 "Measurement information elements" in 3GPP TS 36.331
V10.1.0.
a: This number increases to 384 when the UMPT board is used as the active main control
board.
Event A1 The signal quality of the serving cell exceeds a specific threshold.
Event A2 The signal quality of the serving cell drops below a specific threshold.
Event A3 The signal quality of a neighboring cell exceeds that of the serving cell.
Event A5 The signal quality of the serving cell drops below threshold 1 (Thresh1) and
the signal quality of a neighboring cell exceeds threshold 2 (Thresh2).
Event B2 The signal quality of the serving cell drops below threshold 1 (Thresh1) and
the signal quality of an inter-RAT neighboring cell exceeds threshold 2
(Thresh2).
The entering and leaving conditions of these events are described as follows. For details, see
section 5.5.4 "Measurement report triggering" in 3GPP TS 36.331 V10.1.0.
l Event A1
Entering conditions: (Ms – Hys > Thresh) is true throughout a duration specified by
TimeToTrig.
Leaving conditions: (Ms + Hys < Thresh) is true throughout a duration specified by
TimeToTrig.
Figure 4-3 shows the details.
l Event A2
Entering conditions: (Ms + Hys < Thresh) is true throughout a duration specified by
TimeToTrig.
Leaving conditions: (Ms – Hys > Thresh) is true throughout a duration specified by
TimeToTrig.
Figure 4-4 shows the details.
l Event A3
Entering conditions: (Mn + Ofn + Ocn – Hys > Ms + Ofs + Ocs + Off) is true
throughout a duration specified by TimeToTrig.
Leaving conditions: (Mn + Ofn + Ocn + Hys < Ms + Ofs + Ocs + Off) is true throughout
a duration specified by TimeToTrig.
Figure 4-5 shows the details.
l Event A4
Entering conditions: (Mn + Ofn + Ocn – Hys > Thresh) is true throughout a duration
specified by TimeToTrig.
Leaving conditions: (Mn + Ofn + Ocn + Hys < Thresh) is true throughout a duration
specified by TimeToTrig.
Figure 4-6 shows the details.
l Event A5
Entering conditions: (Ms + Hys < Thresh1) and (Mn + Ofn + Ocn – Hys > Thresh2) are
true throughout a duration specified by TimeToTrig.
Leaving conditions: (Ms – Hys > Thresh1) or (Mn + Ofn + Ocn + Hys < Thresh2) is true
throughout a duration specified by TimeToTrig.
Figure 4-7 shows the details.
l Event B1
Entering conditions: (Mn + Ofn – Hys > Thresh) is true throughout a duration specified
by TimeToTrig.
Leaving conditions: (Mn + Ofn + Hys < Thresh) is true throughout a duration specified
by TimeToTrig.
Figure 4-8 shows the details.
l Event B2
Entering conditions: (Ms + Hys < Thresh1) and (Mn + Ofn – Hys > Thresh2) are true
throughout a duration specified by TimeToTrig.
Leaving conditions: (Ms – Hys > Thresh1) or (Mn + Ofn + Hys < Thresh2) is true
throughout a duration specified by TimeToTrig.
Figure 4-9 shows the details.
l Ms and Mn are the measurement results of the serving cell and a neighboring cell,
respectively.
l Hys is the hysteresis for an event.
l TimeToTrig indicates the duration throughout which a condition is met before the event
can be triggered.
l Thresh, Thresh1, and Thresh2 indicate thresholds.
l Ofs and Ofn indicate the frequency-specific offsets for the serving cell and the
neighboring cell, respectively.
l Ocs and Ocn indicate the CIOs set for the serving cell and the neighboring E-UTRAN
cell, respectively.
l Off indicates the offset for the event.
NOTE
Events A2 and A1 are used to evaluate the signal quality of the serving cell in the handover function
initiation determination phase. Other events are used to evaluate the signal quality of neighboring cells
in the target cell or frequency determination phase.
Measurement configuration delivery and measurement reporting mechanisms of these events (A1 to A5,
B1, and B2) are the same.
The signal quality types of Ms, Mn, Thresh, Thresh1, and Thresh2 are determined by their
triggering quantities.
l Ofs and Ofn, which are considered during inter-frequency handovers
– The Cell.QoffsetFreq parameter specifies Ofs.
– The EutranInterNFreq.QoffsetFreqConn parameter specifies Ofn.
l Ocs and Ocn
– The Cell.CellSpecificOffset parameter specifies Ocs.
– The EutranIntraFreqNCell.CellIndividualOffset parameter specifies Ocn for
intra-frequency neighboring cells.
– The EutranInterFreqNCell.CellIndividualOffset parameter specifies Ocn for
inter-frequency neighboring cells.
l Off, which applies only to event A3
– The IntraFreqHoGroup.IntraFreqHoA3Offset parameter specifies Off for intra-
frequency event A3.
– The InterFreqHoGroup.InterFreqHoA3Offset parameter specifies Off for inter-
frequency event A3.
The signal quality types of Ms, Mn, Thresh, Thresh1, and Thresh2 are determined by their
triggering quantities.
l Ofs and Ofn
– The Cell.QoffsetFreq parameter specifies Ofs.
– The UtranNFreq.OffsetFreq parameter specifies Ofn for neighboring UTRAN
cells.
– The GeranNfreqGroup.OffsetFreq parameter specifies Ofn for neighboring
GERAN cells.
A2 InterRatHoCommGroup.InterRatHoA1A2TimeToTrig specifies
TimeToTrig.
B1 l E-UTRAN to UTRAN
InterRatHoUtranGroup.InterRATHoUtranB1Hyst specifies Hys.
InterRatHoUtranGroup.InterRATHoUtranB1TimeToTrig specifies
TimeToTrig.
B2 l E-UTRAN to GERAN
InterRatHoGeranGroup.InterRatHoGeranB1Hyst specifies Hys.
InterRatHoGeranGroup.InterRatHoGeranB1TimeToTrig specifies
TimeToTrig.
For TimeToTrig used for E-UTRAN to UTRAN handovers, the measurement duration of
offload-oriented and optimization-oriented handovers is controlled by a 3s timer. If
TimeToTrig is longer than 3s, UEs will not send measurement reports to the eNodeB because
the measurements are stopped before the time-to-trigger elapses. In this case, offload-oriented
and optimization-oriented handovers will not be triggered.
The TimeToTrig variable differs depending on UTRAN and GERAN. Operators can set
TimeToTrig to control the event B1 reporting probability. For example, if the TimeToTrig
value for handovers from E-UTRAN to UTRAN is smaller than that for handovers from E-
UTRAN to GERAN, a UE reports event B1 for neighboring UTRAN cells more probably
than event B1 for neighboring GERAN cells, given the same network conditions. Therefore,
the eNodeB sends a handover request more probably to a neighboring UTRAN cell.
QCI 1 2 3 4 5 6 7
Priority 2 4 3 5 1 6 7
QCI 8 9 65 66 69 70 -
Priority 8 9 2 4 1 8 -
Two measurement gap patterns are available: pattern 0 and pattern 1. Measurement duration
and measurement period differ in the two patterns. The HoMeasComm.GapPatternType or
HoMeasComm.DedicatedGapPatternType parameter determines the pattern to be used.
Table 4-12 describes the measurement gap parameters.
If another gap pattern needs to be set up during the gap-assisted measurement, the eNodeB
acts as follows:
l If the current pattern is 0 and the requested new pattern is 1, the eNodeB does not deliver
the new pattern to the UE.
l If the current pattern is 1 and the requested new pattern is 0, the eNodeB delivers the
new pattern to the UE only when the triggering cause of the ongoing gap-assisted
measurement is an unnecessary handover.
The filtering mechanism for different networks is specified by different parameters, as listed
in Table 4-13.
Table 4-13 Parameters that specify Layer 3 (L3) filtering for different networks
Network L3 Filtering Coefficient k
E-UTRAN HoMeasComm.EutranFilterCoeffRSRP
HoMeasComm.EutranFilterCoeffRSRQ
UTRAN HoMeasComm.UtranFilterCoeffRSCP
HoMeasComm.UtranFilterCoeffECN0
GERAN HoMeasComm.GeranFilterCoeff
UE Capabilities
UE capabilities include the supported protocol version, RATs, frequencies, reception and
transmission capabilities (for example, simplex/duplex or double receivers), measurement
capabilities, and handover capabilities. For details, see 3GPP TS 36.331 V10.1.0. The
information to be included in measurement configurations is dependent on UE capabilities.
Measurement-based handover in this document refers to a process in which UEs measure signal quality
of neighboring cells and the eNodeB generates target cells based on measurement reports. The
measurement objects of events A2 and A1 are serving cells. Therefore, measurements for events A2 and
A1 are not discussed within the range of measurement-based handover.
According to section 5.5.3 "Performing measurements" in 3GPP 36.331 V10.1.0, UEs do not
need to perform intra-frequency, inter-frequency, or inter-RAT measurements when the RSRP
of their serving cells is greater than the HoMeasComm.SMeasure parameter value. That is,
UEs do not send measurement reports to the eNodeB in this situation.
also report Ec/N0. In this situation, the handover is triggered only when both RSCP and
Ec/N0 meet the handover conditions. For UEs complying with versions earlier than
3GPP Release 10, the value BOTH is equivalent to the value RSCP.
l When receiving event B1 or B2 reports indicating a handover to GERAN, the eNodeB
generates a candidate cell list based on the measurement reports.
The eNodeB does not perform inter-frequency handover evaluation on a UE whose behavior
does not comply with its reported frequency capabilities. Instead, the eNodeB performs only
intra-frequency or inter-RAT handover evaluation for the UE. The
UECapRprtAbnormalCtrlSwitch option of the
ENodeBAlgoSwitch.CompatibilityCtrlSwitch parameter specifies whether to enable this
function.
Handover in this document is a generic term that covers procedures related to mobility
management in connected mode. In the case of handover policy, handover is a specific term that
refers to service transfer between PS domains.
l Single radio voice call continuity (SRVCC): It applies to VoLTE services. This policy
allows the transfer of VoLTE services from an LTE system to the CS domain of an inter-
RAT network. For details about SRVCC and its activation, see SRVCC.
l Cell change order (CCO) without network assisted cell change (NACC) and CCO with
NACC: These policies apply only to cell changes from a source E-UTRAN cell towards
a target GERAN cell.
– During CCO without NACC (CCO for short), the UE is instructed to switch to the
GERAN idle mode to access a GERAN cell. The procedure is simple but causes an
extended delay.
– CCO with NACC (NACC for short) is an enhancement to CCO. CCO must be
enabled before NACC can be used. During NACC, the eNodeB acquires the system
information of GERAN and then sends the information to the UE through a
handover command. Therefore, NACC accelerates the UE access to the target
GERAN cell.
l Redirection: With this policy, the eNodeB releases a UE and instructs the UE to camp on
a certain frequency.
l Fast redirection: It is an enhanced redirection that enables the eNodeB to instruct a
Release 9-compliant UE to directly access a target cell if the eNodeB has stored system
information about the target cell.
a. The eNodeB selects the RAT that has not been measured.
b. The eNodeB generates a candidate cell or target frequency list according to the
sequences of RAT priority, neighboring cell priority, and frequency priority.
For inter-RAT handovers with the policy being fast redirection, the eNodeB adds cells to or
filters out cells from the candidate cell list.
l In measurement-based mode, the eNodeB adds cells that are not in measurement reports
but working on the target frequency for redirection.
l In blind mode, the eNodeB adds other cells on the target frequency for redirection.
The cells to be delivered are sorted by certain priority, depending on the
UTRAN_SWITCH option of the ENodeBAlgoSwitch.NCellRankingSwitch parameter:
– If this option is selected, the eNodeB adds cells on the target frequency according to
UtranNCell.NCellMeasPriority in descending order.
– If this option is deselected, the eNodeB adds high-priority cells on the target
frequency according to UtranNCell.CellMeasPriority.
l The eNodeB filters out neighboring cells whose system information has not been
obtained.
l The eNodeB filters out neighboring UTRAN cells ranked lower than the value of
InterRatHoComm.CellInfoMaxUtranCellNum when the total number of neighboring
UTRAN cells exceeds this value.
l The eNodeB filters out blacklisted neighboring cells.
l The eNodeB filters out neighboring cells to which handovers are prohibited.
l The eNodeB filters out neighboring cells that do not belong to any PLMN in the PLMN
list.
A PLMN list consists of three parts:
– PLMN that the serving cell belongs to
– Target PLMNs defined in InterPlmnHoList MOs when the InterPlmnHoSwitch
option of the ENodeBAlgoSwitch.HoAlgoSwitch parameter is selected
– Equivalent PLMNs obtained by the eNodeB from the Handover Restriction List IE
from the MME when both the InterPlmnHoSwitch and EPlmnSwitch options of
the ENodeBAlgoSwitch.HoAlgoSwitch parameter are selected
l The eNodeB filters out cells to which handovers are forbidden according to the
Handover Restriction List IE in the INITIAL CONTEXT SETUP REQUEST message
sent from the MME.
l The eNodeB filters out heavy-traffic cells.
When MRFD-101402 UL Unified Overload Control is enabled, cells with heavy traffic
are filtered out from candidate cell lists for service-based inter-RAT handovers. For
necessary handovers, cells with heavy traffic are filtered out, unless no non-heavy-traffic
neighboring cells meet the handover condition.
The eNodeB sends the handover request and forwards data through the X2 or S1
interface adaptively.
– For intra-RAT handovers, the eNodeB sends handover requests and forwards data
through the X2 or S1 interface adaptively. After X2 interfaces are set up, data
forwarding is performed preferentially over the X2 interface.
n For intra-MME inter-eNodeB handovers, handover requests are sent
preferentially over the X2 interface.
NOTE
After the handover to the target cell succeeds, the eNodeB performs data forwarding. If
the handover to the target cell fails, the eNodeB performs retries and penalty.
Retry and penalty policies differ depending on handover admission failure causes. Therefore,
different parameter settings are used to accommodate handover type and handover admission
failure causes. Table 4-16 lists the parameter settings in different scenarios.
l For resource-related handover admission failures, a penalty timer can be set to impose
penalty on the cell. A retry can be initiated to the cell only after the penalty timer
expires.
l For non-resource-related handover admission failures, the number of penalty times can
be set to impose penalty on the cell. A retry can be initiated to the cell only when the
number of penalty times has been reached.
NOTE
l After entering the penalty state, the number of penalty times is incremented by one each time
the measurement result indicates that cell A meets the handover condition.
l If cell A meets the handover condition after a specified number of penalties have been
imposed, the eNodeB sends a handover request to cell A again. This process is termed as retry.
l Resource-related handover admission failures are only those whose failure causes are as
follows:
No radio resources available in target cell
Transport resource unavailable
Not enough User Plane Processing Resources
Radio resources not available
Control Processing Overload
Table 4-16 Penalty and retry settings for handover admission failures
During retry and penalty, the eNodeB may identify whether the penalty is caused by handover
or SRVCC, depending on the L2UBasedHoPolicyPenaltySwitch option setting of the
ENodeBAlgoSwitch.HoCommOptSwitch parameter.
l When this option is deselected, the eNodeB collects the number of penalties and retries
without identifying the penalty causes for measurement reports sent by UEs.
l When this option is selected, the eNodeB identifies the penalty causes for measurement
reports sent by UEs and collects the number of penalties and retries on a per cause basis.
For example, when the eNodeB receives a measurement report for SRVCC:
– If the penalty and retry procedure performed last time was caused by handover,
penalty is not imposed for the measurement report of this time. The SRVCC
procedure is executed when the handover policy fails.
– If the penalty and retry procedure performed last time was caused by SRVCC,
penalty is imposed for the measurement report of this time. In this case, the eNodeB
collects the number of penalties and retries caused by SRVCC.
with an E-RAB failure response, which carries the cause value of "S1 intra system Handover
Triggered", "S1 inter system Handover Triggered", or "X2 Handover triggered". When the
handover is complete, the EPC initiates the E-RAB management procedure again. If the EPC
receiving the E-RAB failure response with a preceding cause value is not capable of
reinitiating the E-RAB management procedure, this procedure will fail.
In this situation, the ErabFlowFirstSwitch option of the
GlobalProcSwitch.HoProcCtrlSwitch parameter must be selected so that the eNodeB
preferentially handles the E-RAB management procedure for intra-RAT inter-eNodeB
handovers or inter-RAT handovers in the handover preparation phase. That is, if the eNodeB
has received procedures such as E-RAB establishment, deletion, or modification before
delivering a handover command over the air interface, the eNodeB sends a HANDOVER
CANCEL message to cancel the handover so that the E-RAB management procedure can be
performed.
4.2.1 Benefits
Ensures service continuity and network performance when UEs move in co-coverage
networks.
Provides a means to transfer UEs and allows flexible networking to meet the service steering
and load balancing requirements of operators.
4.2.2 Impacts
Network Impacts
None
Function Impacts
None
4.3 Requirements
4.3.1 Licenses
None
4.3.2 Software
Before activating this function, ensure that its prerequisite functions have been activated and
mutually exclusive functions have been deactivated. For detailed operations, see the relevant
feature documents.
Prerequisite Functions
None
4.3.3 Hardware
Base Station Models
No requirements
Boards
No requirements
RF Modules
No requirements
4.3.4 Others
None
parameters to activate each handover function, refer to this section to set parameters related to
common configurations.
Common configurations involve a large number of parameters. This section describes only
key parameters. For details about the parameters that are not listed, see principles in other
sections and eNodeB parameter reference.
Mobility is a basic feature to maintain service continuity. Before activating basic functions of
mobility, obtain information about network plan and neighboring cell plan for neighbor
relationship configuration. Table 4-17 lists the MOs related to neighbor relationship
configuration. This helps check whether the configuration is complete. The parameters related
to cell setup are not described in this section.
NOTE
The configurations apply to services with QCIs specified by CellQciPara.Qci. By default, the
configurations of each parameter group in the preceding table are the same for all QCIs. That is, the
configurations with group ID being 0 are used. Customized configurations are supported to apply
different handover parameter groups to services with different QCIs.
The following commands are required only when different inter-RAT handover policies
need to be configured for services with different QCIs.
//Modifying inter-RAT handover policy groups
MOD INTERRATPOLICYCFGGROUP: InterRatPolicyCfgGroupId=0, UtranHoCfg=PS_HO-1;
MOD INTERRATPOLICYCFGGROUP: InterRatPolicyCfgGroupId=1,
UtranHoCfg=REDIRECTION-1;
The following commands are required only when different inter-RAT handover policies
need to be configured for services with different QCIs.
//Modifying inter-RAT handover policy groups
MOD INTERRATPOLICYCFGGROUP: InterRatPolicyCfgGroupId=0,
GeranGprsEdgeHoCfg=PS_HO-1&REDIRECTION-1;
MOD INTERRATPOLICYCFGGROUP: InterRatPolicyCfgGroupId=1,
GeranGprsEdgeHoCfg=PS_HO-1&REDIRECTION-1;
5 Coverage-based Handover
5.1 Overview
Table 5-1 Conditions for starting and stopping each measurement-based coverage-based
handover
Handover Function Starting Condition Stopping Condition
Measurement- and coverage- The signal quality of the The signal quality of the
based inter-frequency serving cell drops below serving cell becomes higher
handover the threshold for inter- than or equal to the
frequency measurement. threshold for inter-frequency
That is, the eNodeB measurement. That is, the
receives the corresponding eNodeB receives the
inter-frequency event A2 corresponding event A1
report. For details, see report.
5.1.4 Event A2 Involved
in Coverage-based
Handover.
Measurement- and coverage- The signal quality of the The signal quality of the
based handover from E- serving cell drops below serving cell becomes higher
UTRAN to UTRAN the threshold for inter- than or equal to the
RAT measurement. That threshold for inter-RAT
Measurement- and coverage- is, the eNodeB receives measurement. That is, the
based handover from E- the corresponding inter- eNodeB receives the
UTRAN to GERAN RAT event A2 report. For corresponding event A1
details, see 5.1.4 Event report.
A2 Involved in
Coverage-based
Handover.
Table 5-2 Conditions for starting and stopping each blind coverage-based handover
Handover Starting Condition Stopping Condition
Function
Blind The signal quality of the serving cell The signal quality of the serving cell
coverage- drops below the threshold for inter- becomes higher than or equal to the
based inter- RAT or inter-frequency blind mode. threshold for inter-RAT or inter-
frequency That is, the eNodeB receives an frequency blind handling. That is,
handover inter-frequency or inter-RAT blind the eNodeB receives the
event A2 report. For details, see corresponding event A1 report.
Blind 5.1.4 Event A2 Involved in
coverage- Coverage-based Handover.
based
handover
from E-
UTRAN to
UTRAN
Blind
coverage-
based
handover
from E-
UTRAN to
GERAN
IntraRatHoComm.InterFreqHoA1A InterFreqHoGroup.
2TrigQuanb InterFreqHoA2ThdR
SRP or
InterFreqHoGroup.
InterFreqHoA2ThdR
SRQb
Event A1 and event A2 usually work in pairs. Therefore, the classifications of event A1 are
the same as those of event A2. That is, event A1 is also classified into inter-frequency event
A1, inter-RAT event A1, and inter-frequency or inter-RAT blind event A1.
NOTE
In the following scenarios, the eNodeB delivers measurement configurations only for blind event A2 but
not for measurement event A2:
l The UE does not support inter-RAT measurements.
l The configured measurement event A2 threshold is lower than or equal to the blind event A2
threshold.
Measurement-based Handover
Upon receiving an inter-RAT event A2 report, the eNodeB starts UTRAN measurement and
GERAN measurement simultaneously by default. This is because the measurement
configuration for inter-RAT event A2 delivered by the eNodeB is not RAT-specific. In
subsequent operations, the eNodeB determines whether to execute the handover to UTRAN or
GERAN based on the decided target cell or target frequency.
If service-type-based RAT steering is enabled, the eNodeB selects only the highest-priority
RAT for measurement after receiving an inter-RAT event A2 report. This is equivalent to
enabling only inter-RAT handover to UTRAN or GERAN. Service-type-based RAT steering
is controlled by parameters in Table 5-4.
NOTE
Blind Handover
Inter-RAT blind handover applies only to services excluding QCI-1 services. The eNodeB
selects highest-priority frequencies based on RAT priority parameters listed in Table 5-5.
NOTE
5.2.1 Principles
The IntraFreqCoverHoSwitch option of the ENodeBAlgoSwitch.HoAlgoSwitch parameter
specifies whether to enable this function.
Intra-frequency handover involves only coverage-based handover. The eNodeB delivers
measurement configurations after RRC connections are set up. Intra-frequency handover does
not include the handover function initiation decision phase because the eNodeB executes the
handover when any target cell meeting the handover requirement is available.
This function does not involve the blind mode. Figure 5-1 shows the differences between this
function and the basic handover process. This section describes only the differences.
The eNodeB acquires target cells for coverage-based intra-frequency handover from event A3
reports. The IntraRatHoComm.IntraFreqHoA3TrigQuan and
IntraRatHoComm.IntraFreqHoA3RprtQuan parameters specify the triggering quantity and
reporting quantity of event A3, respectively.
5.2.2.1 Benefits
Coverage-based intra-frequency handovers reduce interference from intra-frequency
neighboring cells on an intra-frequency network, decreasing the service drop rate.
5.2.2.2 Impacts
Network Impacts
None
Function Impacts
RAT Function Function Reference Description
Name Switch
5.2.3 Requirements
5.2.3.1 Licenses
None
5.2.3.2 Software
Before activating this function, ensure that its prerequisite functions have been activated and
mutually exclusive functions have been deactivated. For detailed operations, see the relevant
feature documents.
Prerequisite Functions
None
5.2.3.3 Hardware
Boards
No requirements
RF Modules
No requirements
5.2.3.4 Others
None
1526726997 L.HHO.IntraeNB.IntraFreq.ExecSuccOut
1526726995 L.HHO.IntraeNB.IntraFreq.PrepAttOut
1526726996 L.HHO.IntraeNB.IntraFreq.ExecAttOut
1526726997 L.HHO.IntraeNB.IntraFreq.ExecSuccOut
5.3.1 Principles
The InterFreqCoverHoSwitch option of the CellHoParaCfg.CellHoAlgoSwitch parameter
specifies whether to enable this function.
l For details about preferential blind handover, see 5.3.1.4.1 Preferential Blind
Handover.
l For details about emergency blind handover, see 5.3.1.4.2 Emergency Blind Handover.
During a coverage-based inter-frequency handover, the sequence that the A1/A2 measurement
configurations are delivered is controlled by the ReduceInvalidA1A2RptSigSwitch option
of the ENodeBAlgoSwitch.HoSignalingOptSwitch parameter.
l If the option is selected, the eNodeB delivers measurement configuration for event A2
first when setting up an RRC connection for a UE. Then, the eNodeB delivers
measurement configuration for event A1 after receiving an event A2 report from the UE.
This reduces unnecessary signaling exchanges. Figure 5-4 shows inter-frequency
measurement based on event A4/A5. Figure 5-6 shows inter-frequency measurement
based on event A3.
l If the option is deselected, the eNodeB delivers both A2 and A1 measurement
configurations when setting up an RRC connection for a UE. Figure 5-5 shows inter-
Figure 5-4 Triggering and stopping of measurement when event A2 configuration is delivered
earlier than event A1 configuration (inter-frequency measurement based on event A4/A5)
Figure 5-5 Triggering and stopping of measurement when event A2 and A1 configurations
are delivered simultaneously (inter-frequency measurement based on event A4/A5)
Figure 5-6 Triggering and stopping of measurement when event A2 configuration is delivered
earlier than event A1 configuration (inter-frequency measurement based on event A3)
Figure 5-7 Triggering and stopping of measurement when event A2 and A1 configurations
are delivered simultaneously (inter-frequency measurement based on event A3)
5.3.1.1.1 Event A2
Table 5-10 describes thresholds related to event A2.
a: The RSRP threshold for event A2 for inter-duplex-mode handovers between FDD and
TDD can be set separately. For details, see Table 5-11.
b: In RAN sharing scenarios, different eNBCnOpQciRsvdPara.RsvdPara14 parameter
values need to be set only when the event A2 RSRP thresholds need to be configured
flexibly for different operators and QCIs.
For inter-duplex-mode handover between FDD and TDD, Huawei eNodeBs allow different
RSRP thresholds for event A2 to be set for FDD and TDD frequencies for events A3/A4/A5.
The different settings enable UEs to be preferentially handed over to FDD or TDD
frequencies during a coverage-based handover. For details, see Table 5-11. This separate
setting is used when FDD and TDD cells are co-sited but FDD cells use different policies
from TDD cells.
When the FDD and TDD threshold offsets are set to different valid values, the eNodeB
delivers the two inter-frequency event A2 thresholds using different measurement IDs. After
receiving event A2 reports from the UE, the eNodeB delivers A3/A4/A5 inter-frequency
measurement configurations based on the following principles:
When any cell-level threshold offset parameter is valid, the cell-level instead of the eNodeB-
level threshold offsets take effect. This policy applies to the FDD and TDD co-sited scenarios
where FDD cell policies differ from TDD cell policies.
5.3.1.1.2 Event A1
Table 5-12 describes thresholds related to event A1.
Table 5-13 Frequency priority parameters when the directional handover function takes
effect
Directional Handover Activation Condition UE Frequency
Condition Priority
Parameter
2. When the conditions in the first column of Table 5-14 are met, the eNodeB selects a
high-priority frequency according to the frequency priority parameters listed in this table
and delivers the measurement configuration. If the priorities are the same, the eNodeB
proceeds with the next step.
Table 5-14 Frequency priority parameters when the directional handover function does
not take effect
Frequency Priority Configuration Frequency Priority Parameter
Policy
3. If the priorities are still the same, the eNodeB randomly selects a high-priority frequency
and delivers the measurement configuration.
When Thresh1 for event A5 is less than or equal to the threshold for blind event A2, the eNodeB does
not deliver measurement configurations related to event A5.
After receiving event A3, A4, or A5 reports, the eNodeB initiates coverage-based inter-
frequency handover based on the value of the CellAlgoSwitch.CovBasedInterFreqHoMode
parameter:
l If the parameter value is HANDOVERIMMEDIATELY, the eNodeB immediately
determines whether to perform the handover when receiving a measurement report.
l If the parameter value is BASEDONSIGNALSTRENGTH, the eNodeB waits a period
specified by IntraRatHoComm.CovBasedIfHoWaitingTimer and then determines
whether to perform the handover to the strongest neighboring cell in the target cell list.
l If the parameter value is BASEDONFREQPRIORITY, the eNodeB preferentially
considers the frequency measurement priority specified by the
EutranInterNFreq.MeasFreqPriority parameter. In addition, the eNodeB considers
signal strength and then determines whether to perform the handover.
The first mode is always adopted for emergency call services. That is, the eNodeB
immediately selects a cell and initiates the handover when receiving a measurement report.
5.3.1.3.1 Event A3
The IntraRatHoComm.A3InterFreqHoA1A2TrigQuan and
IntraRatHoComm.IntraFreqHoA3RprtQuan parameters specify the triggering quantity and
reporting quantity of event A3, respectively.
5.3.1.3.2 Event A4
Table 5-15 describes thresholds related to event A4.
InterFreqHoGroup.InterFreqHoA4ThdR The
SRP + IntraRatHoComm.InterFreqHoA1A2Trig
EutranInterNFreq.IfHoThdRsrpOffset Quan parameter specifies the triggering
quantity.
InterFreqHoGroup.InterFreqHoA4ThdR
SRQ The
IntraRatHoComm.InterFreqHoA4RprtQu
an parameter specifies the reporting
quantity.
5.3.1.3.3 Event A5
Table 5-16 and Table 5-17 describe Thresh1 and Thresh2 for event A5, respectively.
InterFreqHoGroup.InterFreqHoA5Thd1 The
Rsrp IntraRatHoComm.InterFreqHoA1A2Trig
Quan and
InterFreqHoGroup.InterFreqHoA5Thd1 IntraRatHoComm.InterFreqHoA4RprtQu
Rsrq an parameters determine the triggering
quantity and reporting quantity of Thresh1
for event A5, respectively. The triggering
quantity and reporting quantity for event A5
are the same as those for event A4.
InterFreqHoGroup.InterFreqHoA4ThdR The
SRP + IntraRatHoComm.InterFreqHoA1A2Trig
EutranInterNFreq.IfHoThdRsrpOffset Quan and
IntraRatHoComm.InterFreqHoA4RprtQu
InterFreqHoGroup.InterFreqHoA4ThdR an parameters determine the triggering
SRQ quantity and reporting quantity of Thresh2
for event A5, respectively. The triggering
quantity and reporting quantity for event A5
are the same as those for event A4.
Coverage-based blind handover consists of preferential blind handover and emergency blind
handover.
E-UTRAN TDD and E-UTRAN FDD can be considered as two independent RATs in inter-
duplex-mode handovers between FDD and TDD. The priorities of TDD and FDD are
determined as follows:
l If the CnOperatorHoCfg.FirstRatPri parameter is set to EUTRAN, E-UTRAN TDD
and E-UTRAN FDD are not prioritized.
l If the CnOperatorHoCfg.SecondRatPri parameter is set to NULL, handover is
performed only to frequencies of the RAT specified by the
CnOperatorHoCfg.FirstRatPri parameter.
NOTE
The handover policy for preferential blind handover is handover. That is, the eNodeB initiates
a handover to a qualified inter-frequency cell.
The same parameters are used by preferential blind handover and measurement-based
handover for inter-frequency event A2 and A1 reports, as listed in Table 5-10 and Table 5-12.
Therefore, the two functions are always triggered simultaneously.
Compared with measurement-based handovers, target cell selection for preferential blind
handovers is faster because the latter adopts blind mode. This means that a preferential blind
handover is preferentially performed even if the two functions are triggered simultaneously.
The handover policy for emergency blind handover is redirection. That is, the eNodeB
initiates a redirection to a qualified target frequency.
CellHoParaCfg.BlindHoA1A2ThdRsrp The
InterRatHoComm.InterRatHoA1A2TrigQ
CellHoParaCfg.BlindHoA1A2ThdRsrq uan parameter determines the threshold to
be used.
Other event-related parameters except
threshold parameters are the same as those
for inter-RAT events A2 and A1. The
parameters include
InterRatHoCommGroup.InterRatHoA1A
2Hyst and
InterRatHoCommGroup.InterRatHoA1A
2TimeToTrig.
5.3.2.1 Benefits
With coverage-based inter-frequency handovers, the coverage in areas with weak LTE
coverage or coverage holes can be supplemented by inter-frequency neighboring cells,
decreasing the service drop rate.
5.3.2.2 Impacts
Network Impacts
None
Function Impacts
RAT Function Function Reference Description
Name Switch
5.3.3 Requirements
5.3.3.1 Licenses
None
5.3.3.2 Software
Before activating this function, ensure that its prerequisite functions have been activated and
mutually exclusive functions have been deactivated. For detailed operations, see the relevant
feature documents.
Prerequisite Functions
None
5.3.3.3 Hardware
Boards
No requirements
RF Modules
No requirements
5.3.3.4 Others
None
Table 5-19 and Table 5-20 describe the parameters used for function activation and
optimization, respectively.
Frequency RatFreqPriorityGroup.C
Priority for onnFreqPriority
Connected
Mode
– The
InterFreqHoGroup.InterFreqHo
A1ThdRsrp or
InterFreqHoGroup.InterFreqHo
A1ThdRsrq parameter specifies the
threshold for event A1.
l There is no recommended scenario for
event A5.
BlindHO CellHoParaCfg.BlindHoA1A
A1A2 2ThdRsrq
RSRQ
trigger
threshold
After this function is enabled, UEs supporting inter-duplex-mode measurement but not supporting inter-
duplex-mode handover cannot be transferred to an inter-duplex-mode network through measurement-
based redirection. Enabling this function does not affect UEs supporting both inter-duplex-mode
measurement and inter-duplex-mode handover.
l Using counters
Observe the values of the counters listed in Table 5-21. If they have non-zero values, this
function has taken effect.
1526728935 L.HHO.InterFreq.Coverage.ExecSucc
Out
In FDD: This feature supports quick configuration of counter collection by feature using the
U2000. The measurement for the counters related to this feature can be set in a single
operation. These counters are determined by the counter-feature relationships listed in the
performance counter reference. For details about the operations, see "Quickly Setting
Performance Measurement by Feature" in iManager U2000 MBB Network Management
System Product Documentation.
Monitor the counters in Table 5-22 to check the running status of this function.
1526728933 L.HHO.InterFreq.Coverage.PrepAttOut
1526728934 L.HHO.InterFreq.Coverage.ExecAttOut
1526728935 L.HHO.InterFreq.Coverage.ExecSuccOu
t
1526729612 L.HHO.InterFddTdd.Coverage.PrepAtt
Out
1526729613 L.HHO.InterFddTdd.Coverage.ExecAtt
Out
1526729614 L.HHO.InterFddTdd.Coverage.ExecSucc
Out
5.4.1 Principles
This function works only when the UtranRedirectSwitch or UtranPsHoSwitch option of the
CellHoParaCfg.HoModeSwitch parameter is selected.
Figure 5-8 shows the differences between this function and the basic handover process. This
section describes only the differences.
This function involves measurement-based handover and emergency blind handover. Figure
5-9 shows the detailed procedures for the subfunctions.
l For details about starting and stopping, measurement, and target cell decision for
measurement-based handover, see 5.4.1.1 Initiation Decision of Measurement-based
Handover, 5.4.1.2 Measurement Configuration Delivery, and 5.4.1.3 Target Cell
Decision for Measurement-based Mode, respectively.
l For details about emergency blind handover, see 5.4.1.4 Principles of Blind Handover.
Figure 5-10 uses an example to describe the procedures for triggering and stopping inter-RAT
measurement. In this example:
l InterRatHoComm.InterRatHoA1A2TrigQuan is set to BOTH.
l InterRatHoComm.InterRatHoEventType is set to EventB2.
l The TrigQuanBothMeasOptSw option of the
ENodeBAlgoSwitch.HoCommOptSwitch parameter is selected.
During the triggering and stopping of inter-RAT measurement, RSRP- and RSRQ-based
procedures are mutually independent. This helps reduce unnecessary signaling exchanges.
When an RSRP-triggered event A2 report is received, RSRP-based measurement is triggered
irrespective of whether there is RSRQ-based measurement. When RSRP-triggered event A1
report is received, RSRP-based measurement is stopped.
Figure 5-10 Triggering and stopping of inter-RAT measurement when event A2 measurement configurations are
delivered earlier than event A1 measurement configurations
Figure 5-11 Triggering and stopping of inter-RAT measurement when event A2 and A1 measurement
configurations are delivered simultaneously
5.4.1.1.1 Event A2
Table 5-23 describes thresholds related to event A2.
The eNodeB allows different RSRP threshold offsets for event A2 to be set for UTRAN and
GERAN. The different settings enable UEs to be preferentially handed over to UTRAN or
GERAN during a coverage-based handover. For details, see Table 5-24. The actual event A2
threshold is the sum of an RSRP threshold and an RSRP offset.
l If the calculated RSRP threshold is lower than the protocol-specified minimum value
(-140 dBm), the protocol-specified minimum value is used as the RSRP threshold.
l If the calculated RSRP threshold exceeds the protocol-specified maximum value (-43
dBm), the protocol-specified maximum value is used as the RSRP threshold.
5.4.1.1.2 Event A1
Table 5-25 describes thresholds related to event A1.
InterRatHoCommGroup.InterRat The
HoA1ThdRSRP InterRatHoComm.InterRatHoA1A2TrigQuan
parameter specifies the triggering quantity of inter-
InterRatHoCommGroup.InterRat RAT events A1 and A2.
HoA1ThdRSRQ
5.4.1.3.1 Event B1
Table 5-26 describes thresholds related to event B1.
InterRatHoUtranGroup.InterRAT The
HoUtranB1ThdRSCP InterRatHoComm.InterRATHoUtranB1MeasQu
an parameter specifies the measurement quantity.
InterRatHoUtranGroup.InterRAT
HoUtranB1ThdEcN0
5.4.1.3.2 Event B2
Table 5-27 describes Thresh1 and Thresh2 for event B2.
5.4.2.1 Benefits
With coverage-based inter-RAT handovers, the coverage in areas with weak LTE coverage or
coverage holes can be supplemented by inter-RAT neighboring cells, decreasing the service
drop rate.
5.4.2.2 Impacts
Network Impacts
None
Function Impacts
RAT Function Function Reference Description
Name Switch
5.4.3 Requirements
5.4.3.1 Licenses
The operator has purchased and activated the licenses for the features listed in the following
table.
RAT Feature ID Feature Name Model Sales Unit
5.4.3.2 Software
Before activating this function, ensure that its prerequisite functions have been activated and
mutually exclusive functions have been deactivated. For detailed operations, see the relevant
feature documents.
Prerequisite Functions
None
5.4.3.3 Hardware
Boards
No requirements
RF Modules
No requirements
5.4.3.4 Others
The eNodeB must collaborate with EPC equipment for this function to take effect. If the EPC
equipment is provided by Huawei, its version must be SAE1.2 or later. If the EPC equipment
is provided by another vendor, check whether the vendor's equipment supports this function.
Table 5-28 Parameters used for activation of coverage-based inter-RAT handover to UTRAN
Parameter Parameter Option Setting Notes
Name ID
1526729486 L.IRATHO.E2W.Coverage.ExecAttOu
t
1526729491 L.RRCRedirection.E2W.Coverage
Monitor the counters in Table 5-31 to check the running status of this function.
1526729485 L.IRATHO.E2W.Coverage.PrepAttOut
1526729486 L.IRATHO.E2W.Coverage.ExecAttOut
1526729487 L.IRATHO.E2W.Coverage.ExecSuccOut
1526729491 L.RRCRedirection.E2W.Coverage
5.5.1 Principles
This function is available when the GeranPsHoSwitch option of the eNodeB-level parameter
ENodeBAlgoSwitch.HoModeSwitch or the GeranRedirectSwitch option of the cell-level
parameter CellHoParaCfg.HoModeSwitch is selected.
This function is similar to coverage-based inter-RAT handover to UTRAN. For details, see
5.4 Coverage-based Inter-RAT Handover to UTRAN. The following describes the
differences between the two functions.
Table 5-32 lists the thresholds for events B1 and B2 for coverage-based inter-RAT handover
to GERAN.
Table 5-32 Thresholds for events B1 and B2 for coverage-based inter-RAT handover to
GERAN
Value Description
InterRatHoCommGroup.GeranB2Thd1R The
srp InterRatHoComm.InterRatHoA1A2TrigQ
uan parameter specifies the triggering
InterRatHoCommGroup.GeranB2Thd1R quantity of Thresh1 for GERAN event B2.
srq
Blind handover takes effect only when the GeranRedirectSwitch option of the
CellHoParaCfg.HoModeSwitch parameter is selected.
The eNodeB selects target frequency groups with the highest priority and delivers them to the
UE according to the following sequence:
1. The eNodeB selects neighboring cells with the highest priority (specified by
GeranNcell.BlindHoPriority) for redirection. In addition, the eNodeB uses the
frequency group including the frequency corresponding to the highest-priority cell as the
target frequency group. If the priorities are the same, the eNodeB randomly selects a
blind neighboring GERAN cell. If such a cell is unavailable, the eNodeB proceeds with
the next step.
2. The eNodeB selects the GERAN frequency group with the highest priority as the target
frequency group based on the setting of GeranNfreqGroup.ConnFreqPriority. If the
priorities are the same, the eNodeB randomly selects a target frequency group.
5.5.2.1 Benefits
With coverage-based inter-RAT handovers, the coverage in areas with weak LTE coverage or
coverage holes can be supplemented by inter-RAT neighboring cells, decreasing the service
drop rate.
5.5.2.2 Impacts
Network Impacts
None
Function Impacts
RAT Function Function Reference Description
Name Switch
5.5.3 Requirements
5.5.3.1 Licenses
The operator has purchased and activated the licenses for the features listed in the following
table.
5.5.3.2 Software
Before activating this function, ensure that its prerequisite functions have been activated and
mutually exclusive functions have been deactivated. For detailed operations, see the relevant
feature documents.
Prerequisite Functions
None
5.5.3.3 Hardware
Boards
No requirements
RF Modules
No requirements
5.5.3.4 Others
UEs support inter-RAT handover to GERAN. That is, the S1 interface message
UECapabilityInfoIndication includes the "interRAT-PS-HO-ToGERAN" IE with the value
True.
The eNodeB must collaborate with EPC equipment for this function to take effect. If the EPC
equipment is provided by Huawei, its version must be PS11.0 or later. If the EPC equipment
is provided by another vendor, check whether the vendor's equipment supports this function.
Table 5-33 Parameters used for activation of coverage-based inter-RAT handover to GERAN
Parameter Parameter Option Setting Notes
Name ID
l Single/batch configuration
This function can be activated for a single eNodeB or a batch of eNodeBs on the CME.
For detailed operations, see CME-based Feature Configuration.
1526729489 L.IRATHO.E2G.Coverage.ExecAttOut
1526729492 L.RRCRedirection.E2G.Coverage
1526729488 L.IRATHO.E2G.Coverage.PrepAttOut
1526729489 L.IRATHO.E2G.Coverage.ExecAttOut
1526729490 L.IRATHO.E2G.Coverage.ExecSuccOut
1526729492 L.RRCRedirection.E2G.Coverage
5.6.1 Principles
This section describes PS steering in coverage-based E-UTRAN to UTRAN CS/PS steering.
For details about CS steering, see CS Fallback.
a. The eNodeB selects the frequency with the highest priority (specified by the
UtranNFreq.PsPriority parameter) for measurement. If the priorities are the same,
the eNodeB proceeds with the next step.
b. The eNodeB selects a frequency for measurement according to the
UtranNFreq.ConnFreqPriority setting. If the priorities are the same, the eNodeB
randomly selects a frequency for measurement.
l When the UtranFreqLayerBlindSwitch option of the
CellAlgoSwitch.FreqLayerSwitch parameter is selected, the eNodeB selects a frequency
with the highest priority for emergency blind inter-RAT handover to UTRAN as follows:
a. The eNodeB preferentially selects a frequency with the highest priority (specified
by UtranNFreq.PsPriority) for measurement. If the priorities are the same, the
eNodeB proceeds with the next step.
b. The eNodeB selects the frequency of the neighboring cell with the highest priority
(specified by UtranNCell.BlindHoPriority) for measurement. If the priorities are
the same, the eNodeB proceeds with the next step.
c. The eNodeB selects the frequency with the highest priority (specified by
UtranNFreq.ConnFreqPriority) for measurement. If the priorities are the same,
the eNodeB randomly selects a target frequency.
5.6.2.1 Benefits
With coverage-based E-UTRAN to UTRAN CS/PS steering, the eNodeB selects different
target frequencies for CS and PS services during inter-RAT handover to UTRAN. This
ensures service continuity and reduces the service drop rate.
5.6.2.2 Impacts
Network Impacts
None
Function Impacts
None
5.6.3 Requirements
5.6.3.1 Licenses
The operator has purchased and activated the licenses for the features listed in the following
table.
5.6.3.2 Software
Before activating this function, ensure that its prerequisite functions have been activated and
mutually exclusive functions have been deactivated. For detailed operations, see the relevant
feature documents.
Prerequisite Functions
RAT Function Function Reference Description
Name Switch
5.6.3.3 Hardware
Boards
No requirements
RF Modules
No requirements
5.6.3.4 Others
None
Table 5-37 and Table 5-38 describe the parameters used for function activation and
optimization, respectively.
Monitor the counters in Table 5-39 to check the running status of this function.
1526729485 L.IRATHO.E2W.Coverage.PrepAttOut
1526729486 L.IRATHO.E2W.Coverage.ExecAttOut
1526729487 L.IRATHO.E2W.Coverage.ExecSuccOut
1526729491 L.RRCRedirection.E2W.Coverage
6 Service-based Handover
6.1 Overview
This function allows services with different QCIs to be carried by different frequencies. This
function supports measurement-based handovers.
Table 6-1 lists the conditions for starting and stopping the preceding functions.
6.2.1 Principles
This function is available only when both of the following options are selected:
l ServiceBasedInterFreqHoSwitch option of the ENodeBAlgoSwitch.HoAlgoSwitch
parameter
l SrvBasedInterFreqHoSw option of the CellAlgoSwitch.HoAllowedSwitch parameter
Figure 6-1 shows the differences between this function and the basic handover process. This
section describes only the differences.
InterFreqHoGroup.InterFreqLoadBased- The
HoA4ThdRSRP + IntraRatHoComm.InterFreqHoA4TrigQu
EutranInterNFreq.IfSrvHoThdRsrpOffset an parameter specifies the triggering
quantity.
InterFreqHoGroup.InterFreqLoadBased-
HoA4ThdRSRQ + The
EutranInterNFreq.IfSrvHoThdRsrqOffset IntraRatHoComm.InterFreqHoA4RprtQu
an parameter specifies the reporting
quantity.
After receiving a service-based event A4 report, the eNodeB considers the load status and
bandwidth of cells for CA-incapable UEs when the ServiceBasedMultiFreqHoSwitch option
Only the inter-frequency neighboring cells with the EutranInterFreqNCell.OverlapInd parameter set
to YES send load information over the X2 interface. A neighboring cell is regarded as lightly loaded if
either of the following conditions is met:
l The number of UL-sync UEs in the neighboring cell is less than the sum of the
CellMLB.InterFreqMlbUeNumThd and CellMLB.InterFrqUeNumOffloadOffset parameter
values of the serving cell.
l The neighboring cell load information is unavailable.
For CA-capable UEs, the eNodeB does not preferentially select target cells. In this case, it is
recommended that the CaSmartSelectionSwitch option of the ENodeBAlgoSwitch.CaAlgoSwitch
parameter be selected so that the eNodeB selects more suitable carrier combination for each CA-capable
UE. For details, see Carrier Aggregation.
Assume that a UE is handed over from frequency A to a cell on frequency B and a service-
based inter-frequency handover is then triggered for the UE in the cell on frequency B. In this
situation:
In FDD, the eNodeB can select the source frequency (frequency A) as the target frequency for
this UE if the ServBasedHoBackSwitch option of the CellAlgoSwitch.HoAllowedSwitch
parameter is selected.
When the NCellSelectSwitch option of the CellMlbHo.MlbMatchOtherFeatureMode
parameter is selected, an intra-eNodeB neighboring cell for which MLB is triggered can act as
a target cell. When this option is deselected, this neighboring cell cannot act as the target cell.
6.2.2.1 Benefits
This function provides a means to transfer UEs and allows flexible networking to meet the
service steering requirements of operators.
6.2.2.2 Impacts
Network Impacts
None
Function Impacts
RAT Function Function Reference Description
Name Switch
6.2.3 Requirements
6.2.3.1 Licenses
None
6.2.3.2 Software
Before activating this function, ensure that its prerequisite functions have been activated and
mutually exclusive functions have been deactivated. For detailed operations, see the relevant
feature documents.
Prerequisite Functions
None
6.2.3.3 Hardware
Boards
No requirements
RF Modules
No requirements
6.2.3.4 Others
None
Table 6-3 and Table 6-4 describe the parameters used for function activation and
optimization, respectively.
After this function is enabled, UEs supporting inter-duplex-mode measurement but not supporting inter-
duplex-mode handover cannot be transferred to an inter-duplex-mode network through measurement-
based redirection. Enabling this function does not affect UEs supporting both inter-duplex-mode
measurement and inter-duplex-mode handover.
//Enabling LTE inter-duplex-mode measurement optimization
MOD GLOBALPROCSWITCH: UeCompatSwitch=InterFddTddMeasComOptSw-1;
1526729481 L.HHO.InterFreq.Service.ExecSuccOu
t
operation. These counters are determined by the counter-feature relationships listed in the
performance counter reference. For details about the operations, see "Quickly Setting
Performance Measurement by Feature" in iManager U2000 MBB Network Management
System Product Documentation.
1526729479 L.HHO.InterFreq.Service.PrepAttOut
1526729480 L.HHO.InterFreq.Service.ExecAttOut
1526729481 L.HHO.InterFreq.Service.ExecSuccOut
1526730002 L.HHO.InterFddTdd.Service.PrepAttOut
1526730003 L.HHO.InterFddTdd.Service.ExecAttOu
t
1526730004 L.HHO.InterFddTdd.Service.ExecSuccO
ut
1526737785 L.HHO.InterFddTdd.Service.Meas.Time
out
1526737872 L.HHO.InterFddTdd.Service.AttFail.No
NRT
6.3.1 Principles
The UtranServiceHoSwitch option of the ENodeBAlgoSwitch.HoAlgoSwitch parameter
specifies whether to enable this function.
Figure 6-2 shows the differences between this function and the basic handover process. This
section describes only the differences.
NOTE
Service-based inter-RAT handovers for QCI 1 services is not recommended. This is because
VoLTE services may fail on live networks due to single radio voice call continuity before ringing
(bSRVCC). Service-based inter-RAT handovers for QCI 1 services will increase the bSRVCC
probability. The CellHoParaCfg.SrvccMrDelayTimer parameter is mainly used to solve the
coverage-based bSRVCC problem.
Table 6-7 Thresholds related to event B1 for service-based inter-RAT handover to UTRAN
Value Description
InterRatHoUtranGroup.LdSvBasedHoUt The
ranB1ThdRSCP InterRatHoComm.InterRATHoUtranB1M
easQuan parameter specifies the
InterRatHoUtranGroup.LdSvBasedHoUt measurement quantity of event B1.
ranB1ThdECN0
6.3.2.1 Benefits
This function provides a means to transfer UEs and allows flexible networking to meet the
service steering requirements of operators.
6.3.2.2 Impacts
Network Impacts
None
Function Impacts
None
6.3.3 Requirements
6.3.3.1 Licenses
The operator has purchased and activated the licenses for the features listed in the following
table.
6.3.3.2 Software
Before activating this function, ensure that its prerequisite functions have been activated and
mutually exclusive functions have been deactivated. For detailed operations, see the relevant
feature documents.
Prerequisite Functions
RAT Function Function Reference Description
Name Switch
6.3.3.3 Hardware
Boards
No requirements
RF Modules
No requirements
6.3.3.4 Others
The eNodeB must collaborate with EPC equipment for this function to take effect. If the EPC
equipment is provided by Huawei, its version must be SAE1.2 or later. If the EPC equipment
is provided by another vendor, check whether the vendor's equipment supports this function.
Table 6-8 Parameters used for activation of service-based inter-RAT handover to UTRAN
Parameter Parameter ID Setting Notes
Name
Table 6-9 Parameters used for optimization of service-based inter-RAT handover to UTRAN
Parameter Parameter ID Setting Notes
Name
l Using counters
Observe the values of the counters listed in Table 6-10. If either of the counters has a
non-zero value, this function has taken effect.
1526730019 L.IRATHO.E2W.Service.ExecAttOut
1526730024 L.RRCRedirection.E2W.Service
Monitor the counters in Table 6-11 to check the running status of this function.
1526730018 L.IRATHO.E2W.Service.PrepAttOut
1526730019 L.IRATHO.E2W.Service.ExecAttOut
1526730020 L.IRATHO.E2W.Service.ExecSuccOut
1526730024 L.RRCRedirection.E2W.Service
6.4.1 Principles
The GeranServiceHoSwitch option of the ENodeBAlgoSwitch.HoAlgoSwitch parameter
specifies whether to enable this function.
The principles for this function are similar to those for service-based inter-RAT handover to
UTRAN. The differences lie in the parameters listed in Table 6-12.
Table 6-12 Thresholds related to event B1 for service-based inter-RAT handover to GERAN
Value Description
6.4.2.1 Benefits
This function provides a means to transfer UEs and allows flexible networking to meet the
service steering requirements of operators.
6.4.2.2 Impacts
Network Impacts
None
Function Impacts
None
6.4.3 Requirements
6.4.3.1 Licenses
The operator has purchased and activated the licenses for the features listed in the following
table.
RAT Feature ID Feature Name Model Sales Unit
6.4.3.2 Software
Before activating this function, ensure that its prerequisite functions have been activated and
mutually exclusive functions have been deactivated. For detailed operations, see the relevant
feature documents.
Prerequisite Functions
RAT Function Function Reference Description
Name Switch
6.4.3.3 Hardware
Boards
No requirements
RF Modules
No requirements
6.4.3.4 Others
UEs support inter-RAT handover to GERAN. That is, the S1 interface message
UECapabilityInfoIndication includes the "interRAT-PS-HO-ToGERAN" IE with the value
True.
The eNodeB must collaborate with EPC equipment for this function to take effect. If the EPC
equipment is provided by Huawei, its version must be PS11.0 or later. If the EPC equipment
is provided by another vendor, check whether the vendor's equipment supports this function.
Table 6-13 Parameters used for activation of service-based inter-RAT handover to GERAN
Parameter Parameter Option Setting Notes
Name ID
Table 6-14 Parameters used for optimization of service-based inter-RAT handover to GERAN
Parameter Parameter ID Setting Notes
Name
InterRatHoState=MUST_HO;
MOD CNOPERATORQCIPARA: CnOperatorId=0, Qci=1, ServiceIrHoCfgGroupId=0;
l Using counters
Observe the values of the counters listed in Table 6-15. If either of the counters has a
non-zero value, this function has taken effect.
1526730022 L.IRATHO.E2G.Service.ExecAttOut
1526730025 L.RRCRedirection.E2G.Service
Monitor the counters in Table 6-16 to check the running status of this function.
1526730021 L.IRATHO.E2G.Service.PrepAttOut
1526730022 L.IRATHO.E2G.Service.ExecAttOut
1526730023 L.IRATHO.E2G.Service.ExecSuccOut
1526730025 L.RRCRedirection.E2G.Service
7 Distance-based Handover
7.1 Overview
The CellAlgoSwitch.DistBasedHoSwitch parameter specifies whether to enable distance-
based handover. This function supports only measurement-based handover.
As shown in Figure 7-1, band F1 is used to cover urban areas and band F2 is used to cover
suburban areas. If there are few obstacles in the overlapping area between urban and suburban
areas, the RF signals from an F1 cell may be able to travel a long distance (typically three
times the distance between sites), causing overshoot coverage to an F2 cell. The triangle area
in the UE moving direction indicates overshoot coverage. In this figure, cell 4 is not a
neighboring cell of cell 1.
As a result of overshoot coverage effect of cell 1, a UE cannot trigger a coverage-based inter-
frequency handover in cell 2 and cell 3. When the UE reaches cell 4 and moves out of the
overshoot coverage area, service drops will occur due to lack of neighbor relationships.
When distance-based handover is enabled, the eNodeB monitors its distance to the UE so that
the UE can be handed over to cell 2 or cell 3 in time to avoid service drops.
NOTE
The eNodeB acquires its distance to the UE using the uplink timing advance (TA) mechanism. The
precision in the estimated distance is about 100 to 150 meters.
Table 7-1 describes the conditions for triggering and stopping each distance-based handover
function. If all distance-based handover functions are enabled and triggering conditions are
met, the eNodeB delivers inter-frequency, UTRAN, and GERAN measurement. Then, the
eNodeB determines whether to execute an inter-frequency handover or inter-RAT handover to
UTRAN or GERAN after determining target cells or frequencies.
Distance- Distance between the UE and The distance between the UE and the
based inter- eNodeB exceeds the specified eNodeB falls below the specified
frequency threshold. threshold.
handover
Distance-
based inter-
RAT
handover to
UTRAN
Distance-
based inter-
RAT
handover to
GERAN
7.2.1 Principles
This function takes effect when the DistBasedHO.DistBasedMeasObjType parameter is set
to EUTRAN.
Inter-duplex-mode handover between FDD and TDD is also a type of inter-frequency
handover.
Figure 7-2 shows the differences between this function and the basic handover process. This
section describes only the differences.
Value Description
InterFreqHoGroup.InterFreqHoA4ThdRSR The
P IntraRatHoComm.InterFreqHoA4Trig
Quan parameter specifies the triggering
InterFreqHoGroup.InterFreqHoA4ThdRSR quantity.
Q
The
IntraRatHoComm.InterFreqHoA4Rprt
Quan parameter specifies the reporting
quantity.
7.2.2.1 Benefits
This function ensures the continuity of radio network coverage and provides uninterrupted
communication services for UEs.
7.2.2.2 Impacts
Network Impacts
None
Function Impacts
None
7.2.3 Requirements
7.2.3.1 Licenses
None
7.2.3.2 Software
Before activating this function, ensure that its prerequisite functions have been activated and
mutually exclusive functions have been deactivated. For detailed operations, see the relevant
feature documents.
Prerequisite Functions
None
7.2.3.3 Hardware
Boards
No requirements
RF Modules
No requirements
7.2.3.4 Others
None
l Using counters
Observe the values of the counters listed in Table 7-6. If they have non-zero values, this
function has taken effect.
1526730014 L.HHO.InterFreq.Distance.ExecSuccO
ut
Monitor the counters in Table 7-7 to check the running status of this function.
1526730010 L.HHO.InterFreq.Distance.PrepAttOut
1526730012 L.HHO.InterFreq.Distance.ExecAttOut
1526730014 L.HHO.InterFreq.Distance.ExecSuccOut
1526730011 L.HHO.InterFddTdd.Distance.PrepAttO
ut
1526730013 L.HHO.InterFddTdd.Distance.ExecAttO
ut
1526730015 L.HHO.InterFddTdd.Distance.ExecSucc
Out
7.3.1 Principles
This function takes effect when the DistBasedHO.DistBasedMeasObjType parameter is set
to UTRAN.
Figure 7-3 shows the differences between this function and the basic handover process. This
section describes only the differences.
The initiation determination mechanism of this function is the same as that of distance-based
inter-frequency handover. The eNodeB acquires target cells from event B1 reports. The
thresholds related to event B1 for this function are the same as those for coverage-based
handover. For details, see Table 7-8.
Table 7-8 Thresholds related to event B1 for distance-based inter-RAT handover to UTRAN
Value Description
InterRatHoUtranGroup.InterRATHoUtra The
nB1ThdRSCP InterRatHoComm.InterRATHoUtranB1M
easQuan parameter specifies the
InterRatHoUtranGroup.InterRATHoUtra measurement quantity.
nB1ThdEcN0
7.3.2.1 Benefits
This function ensures the continuity of radio network coverage and provides uninterrupted
communication services for UEs.
7.3.2.2 Impacts
Network Impacts
None
Function Impacts
None
7.3.3 Requirements
7.3.3.1 Licenses
The operator has purchased and activated the licenses for the features listed in the following
table.
7.3.3.2 Software
Before activating this function, ensure that its prerequisite functions have been activated and
mutually exclusive functions have been deactivated. For detailed operations, see the relevant
feature documents.
Prerequisite Functions
RAT Function Name Function Switch Reference
7.3.3.3 Hardware
Boards
No requirements
RF Modules
No requirements
7.3.3.4 Others
None
Table 7-9 and Table 7-10 describe the parameters used for function activation and
optimization, respectively.
Table 7-9 Parameters used for activation of distance-based inter-RAT handover to UTRAN
1526730035 L.IRATHO.E2W.Distance.ExecAttOut
1526730040 L.RRCRedirection.E2W.Distance
1526730034 L.IRATHO.E2W.Distance.PrepAttOut
1526730035 L.IRATHO.E2W.Distance.ExecAttOut
1526730036 L.IRATHO.E2W.Distance.ExecSuccOut
1526730040 L.RRCRedirection.E2W.Distance
7.4.1 Principles
This function takes effect when the DistBasedHO.DistBasedMeasObjType parameter is set
to GERAN.
Figure 7-4 shows the differences between this function and the basic handover process. This
section describes only the differences.
The initiation determination mechanism of this function is the same as that of distance-based
inter-frequency handover. The eNodeB acquires target cells from event B1 reports. The
thresholds related to event B1 for this function are the same as those for coverage-based
handover. For details, see Table 7-13.
Table 7-13 Thresholds related to event B1 for distance-based inter-RAT handover to GERAN
Value Description
7.4.2.1 Benefits
This function ensures the continuity of radio network coverage and provides uninterrupted
communication services for UEs.
7.4.2.2 Impacts
Network Impacts
None
Function Impacts
None
7.4.3 Requirements
7.4.3.1 Licenses
The operator has purchased and activated the licenses for the features listed in the following
table.
7.4.3.2 Software
Before activating this function, ensure that its prerequisite functions have been activated and
mutually exclusive functions have been deactivated. For detailed operations, see the relevant
feature documents.
Prerequisite Functions
RAT Function Name Function Switch Reference
7.4.3.3 Hardware
Boards
No requirements
RF Modules
No requirements
7.4.3.4 Others
None
Table 7-14 and Table 7-15 describe the parameters used for function activation and
optimization, respectively.
Table 7-14 Parameters used for activation of distance-based inter-RAT handover to GERAN
1526730038 L.IRATHO.E2G.Distance.ExecAttOut
1526730041 L.RRCRedirection.E2G.Distance
1526730037 L.IRATHO.E2G.Distance.PrepAttOut
1526730038 L.IRATHO.E2G.Distance.ExecAttOut
1526730039 L.IRATHO.E2G.Distance.ExecSuccOut
1526730041 L.RRCRedirection.E2G.Distance
8 UL-quality-based Handover
8.1 Overview
UL-quality-based handover decreases the number of service drops caused by deteriorated
uplink quality. The eNodeB determines whether to execute an inter-frequency handover or
inter-RAT handover to UTRAN or GERAN after determining target cells or frequencies.
UL-quality-based handover involves measurement-based and blind handovers. Table 8-1 lists
the conditions for triggering and stopping UL-quality-based handover.
8.2.1 Principles
The UlQualityInterFreqHoSwitch option of the ENodeBAlgoSwitch.HoAlgoSwitch
parameter specifies whether to enable this function.
Figure 8-1 shows the differences between this function and the basic handover process. This
section describes only the differences.
InterFreqHoGroup.InterFreqHoA4ThdRSRP + The
InterFreqHoGroup.UlBadQualHoA4Offset IntraRatHoComm.InterFreqHoA4
TrigQuan parameter specifies the
InterFreqHoGroup.InterFreqHoA4ThdRSRQ + triggering quantity.
InterFreqHoGroup.UlBadQualHoA4Offset
The
IntraRatHoComm.InterFreqHoA4
RprtQuan parameter specifies the
reporting quantity.
Initiation Decision
If the UL quality for the UE further deteriorates, the eNodeB considers that a service drop
may occur due to the poor UL quality and performs blind redirection for the UE when the
following conditions are met:
l Uplink MCS index < CellHoParaCfg.UlBadQualHoMcsThd parameter value
l Actual IBLER of uplink data transmission – Target IBLER value – 10% >
CellHoParaCfg.UlBadQualHoIblerThd parameter value
l The eNodeB fails to receive any event A4 reports.
When CellAlgoSwitch.VolteRedirectSwitch is turned on, blind redirection can be
executed for QCI-1 services during UL-quality-based inter-frequency handovers. In this
case, the cause value in the release message sent from the eNodeB to the MME is always
User Inactivity.
8.2.2.1 Benefits
This function ensures the continuity of radio network coverage and provides uninterrupted
communication services for UEs.
8.2.2.2 Impacts
Network Impacts
None
Function Impacts
None
8.2.3 Requirements
8.2.3.1 Licenses
None
8.2.3.2 Software
Before activating this function, ensure that its prerequisite functions have been activated and
mutually exclusive functions have been deactivated. For detailed operations, see the relevant
feature documents.
Prerequisite Functions
None
8.2.3.3 Hardware
Boards
No requirements
RF Modules
No requirements
8.2.3.4 Others
None
l Using counters
Observe the value of the counter listed in Table 8-6. If it has a non-zero value, this
function has taken effect.
1526729998 L.HHO.InterFreq.ULquality.ExecSucc
Out
1526729994 L.HHO.InterFreq.ULquality.PrepAttOut
1526729996 L.HHO.InterFreq.ULquality.ExecAttOut
1526729998 L.HHO.InterFreq.ULquality.ExecSuccO
ut
1526729995 L.HHO.InterFddTdd.ULquality.PrepAtt
Out
1526729997 L.HHO.InterFddTdd.ULquality.ExecAtt
Out
1526729999 L.HHO.InterFddTdd.ULquality.ExecSuc
cOut
8.3.1 Principles
The UlQualityInterRATHoSwitch option of the ENodeBAlgoSwitch.HoAlgoSwitch
parameter specifies whether to enable this function. If this option is selected, UEs can be
handed over to UTRAN or GERAN cells.
Figure 8-2 shows the differences between this function and the basic handover process. This
section describes only the differences.
The initiation determination mechanism of this function is the same as that of UL-quality-
based inter-frequency handover.
In measurement-based handover, the eNodeB acquires target cells from event B1 reports. The
thresholds related to event B1 for this function are the same as those for coverage-based
handover.
l Table 8-8 lists the thresholds related to event B1 for UTRAN cells.
l Table 8-9 lists the thresholds related to event B1 for GERAN cells.
InterRatHoUtranGroup.InterRATHoUtra The
nB1ThdRSCP InterRatHoComm.InterRATHoUtranB1M
easQuan parameter specifies the
InterRatHoUtranGroup.InterRATHoUtra measurement quantity.
nB1ThdEcN0
In UL-quality-based inter-RAT blind handover to UTRAN, the eNodeB selects the frequency
with the highest priority as follows:
1. The eNodeB selects the frequency of the neighboring cell with the highest priority
(specified by UtranNCell.BlindHoPriority) for measurement. If the priorities are the
same, the eNodeB proceeds with the next step.
2. The eNodeB selects the frequency with the highest priority (specified by
UtranNFreq.ConnFreqPriority) for measurement. If the priorities are the same, the
eNodeB randomly selects a target frequency.
In UL-quality-based inter-RAT blind handover to GERAN, the eNodeB selects the frequency
group with the highest priority as follows:
1. The eNodeB selects the frequency of the neighboring cell with the highest priority
(specified by GeranNcell.BlindHoPriority) for measurement. If the priorities are the
same, the eNodeB proceeds with the next step.
2. The eNodeB selects the frequency group with the highest priority (specified by
GeranNfreqGroup.ConnFreqPriority) for measurement. If the priorities are the same,
the eNodeB randomly selects a target frequency group.
8.3.2.1 Benefits
This function ensures the continuity of radio network coverage and provides uninterrupted
communication services for UEs.
8.3.2.2 Impacts
Network Impacts
None
Function Impacts
None
8.3.3 Requirements
8.3.3.1 Licenses
The operator has purchased and activated the licenses for the features listed in the following
table to use UL-quality-based inter-RAT handover to UTRAN.
RAT Feature ID Feature Name Model Sales Unit
The operator has purchased and activated the licenses for the features listed in the following
table to use UL-quality-based inter-RAT handover to GERAN.
8.3.3.2 Software
Before activating this function, ensure that its prerequisite functions have been activated and
mutually exclusive functions have been deactivated. For detailed operations, see the relevant
feature documents.
Prerequisite Functions
RAT Function Function Reference Description
Name Switch
8.3.3.3 Hardware
Boards
No requirements
RF Modules
No requirements
8.3.3.4 Others
None
l Using counters
Observe the values of the counters listed in Table 8-12. If either of the counters has a
non-zero value, UL-quality-based inter-RAT handover to UTRAN has taken effect.
1526730027 L.IRATHO.E2W.ULquality.ExecAttOu
t
1526730032 L.RRCRedirection.E2W.Ulquality
Observe the values of the counters listed in Table 8-13. If either of the counters has a
non-zero value, UL-quality-based inter-RAT handover to GERAN has taken effect.
1526730030 L.IRATHO.E2G.ULquality.ExecAttOu
t
1526730033 L.RRCRedirection.E2G.Ulquality
Monitor the counters in Table 8-14 to check the running status of this function.
1526730026 L.IRATHO.E2W.ULquality.PrepAttOut
1526730027 L.IRATHO.E2W.ULquality.ExecAttOut
1526730028 L.IRATHO.E2W.ULquality.ExecSuccOut
1526730032 L.RRCRedirection.E2W.Ulquality
1526730029 L.IRATHO.E2G.ULquality.PrepAttOut
1526730030 L.IRATHO.E2G.ULquality.ExecAttOut
1526730031 L.IRATHO.E2G.ULquality.ExecSuccOut
1526730033 L.RRCRedirection.E2G.Ulquality
9 Service-request-based Inter-frequency
Handover
9.1 Principles
The ServiceReqInterFreqHoSwitch option of the CellAlgoSwitch.HoAllowedSwitch
parameter specifies whether to enable this function. This function supports only
measurement-based handover.
NOTE
For cells on TDD frequencies, this function can also be enabled or disabled by the
ServiceReqInterFreqHoSwitch option of the ENodeBAlgoSwitch.HoAlgoSwitch parameter. This
means that either the cell- or eNodeB-level parameter can control this feature. This option will not be
used in later versions and therefore is not recommended.
For cells on FDD frequencies, this function is not controlled by the eNodeB-level parameter.
When this option is selected, the eNodeB sets up bearers for QCI-1 services if the
ServiceIfHoCfgGroup.InterFreqHoState parameter value is PERMIT_HO in the UE initial
context. Then, the eNodeB initiates inter-frequency measurement after the UE accesses the
network.
l If this option is deselected, the eNodeB selects the frequencies for measurement in
descending order of frequency priority specified by
ServiceIfDlEarfcnGrp.ServiceHoFreqPriority.
l If this option is selected, the eNodeB selects the frequencies for measurement in
descending order of frequency priority specified by
EutranInterNFreq.MeasFreqPriority.
The duration of gap-assisted inter-frequency measurements triggered for service-request-
based inter-frequency handovers must be restricted. This prevents persistent measurements
performed due to failures to receive measurement reports from affecting data transmission.
The duration is specified by the ServiceIfHoCfgGroup.A4RptWaitingTimer parameter.
InterFreqHoGroup.SrvReqHoA4ThdRsrp The
+ EutranInterNFreq.IfSrvHoThdRsrpOff- IntraRatHoComm.InterFreqHoA4TrigQu
set an parameter specifies the triggering
quantity.
InterFreqHoGroup.SrvReqHoA4ThdRsrq
+ EutranInterNFreq.IfSrvHoThdRsrqOff- The
set IntraRatHoComm.InterFreqHoA4RprtQu
an parameter specifies the reporting
quantity.
Assume that a UE is handed over from frequency A to a cell on frequency B and a service-
request-based inter-frequency handover is then triggered for the UE in the cell on frequency
B. In this situation:
In FDD, the eNodeB can select the source frequency (frequency A) as the target frequency for
this UE if the ServBasedHoBackSwitch option of the CellAlgoSwitch.HoAllowedSwitch
parameter is selected.
The eNodeB always adopts the following policies for FDD:
l During an incoming handover of the UE, the target eNodeB allows the handover.
l If the handover of the UE fails and the UE continues to camp on the source eNodeB, the
eNodeB does not remove the bearers with this QCI.
9.2.1 Benefits
This function provides a means to transfer UEs and allows flexible networking to meet the
service steering requirements of operators.
9.2.2 Impacts
Network Impacts
None
Function Impacts
RAT Function Function Reference Description
Name Switch
9.3 Requirements
9.3.1 Licenses
There are no FDD license requirements.
9.3.2 Software
Before activating this function, ensure that its prerequisite functions have been activated and
mutually exclusive functions have been deactivated. For detailed operations, see the relevant
feature documents.
Prerequisite Functions
None
9.3.3 Hardware
Boards
No requirements
RF Modules
No requirements
9.3.4 Others
None
Table 9-2 and Table 9-3 describe the parameters used for function activation and
optimization, respectively.
l Using counters
Observe the value of the counter listed in Table 9-4. If it has a non-zero value, this
function has taken effect.
1526729481 L.HHO.InterFreq.Service.ExecSuccOu
t
Monitor the counters in Table 9-5 to check the running status of this function.
1526729479 L.HHO.InterFreq.Service.PrepAttOut
1526729480 L.HHO.InterFreq.Service.ExecAttOut
1526729481 L.HHO.InterFreq.Service.ExecSuccOut
1526730002 L.HHO.InterFddTdd.Service.PrepAttOut
1526730003 L.HHO.InterFddTdd.Service.ExecAttOu
t
1526730004 L.HHO.InterFddTdd.Service.ExecSuccO
ut
1526737785 L.HHO.InterFddTdd.Service.Meas.Time
out
1526737872 L.HHO.InterFddTdd.Service.AttFail.No
NRT
10 Frequency-priority-based Inter-
frequency Handover
10.1 Principles
The FreqPriorIFHOSwitch option of the CellAlgoSwitch.FreqPriorityHoSwitch parameter
specifies whether to enable this function. This function involves measurement-based and
blind handovers.
example of such scenarios, where 900 MHz is the low band and 1800 MHz is the high
band.
NOTE
Figure 10-3 shows the differences between this function and the basic handover process. This
section describes only the differences.
When a UE accesses a cell (including entering RRC connected mode from idle mode,
incoming handover, and incoming RRC connection reestablishment), this function takes effect
if all the following conditions are met:
l The HO_USE_VOIP_FREQ_ALLOWED option of the CellQciPara.QciAlgoSwitch
parameter is deselected for all QCIs of the services running on the UE when the
VoipMeasFreqPriSwitch option of the CellAlgoSwitch.MultiFreqPriControlSwitch
parameter is selected.
NOTE
During bearer setup and release, this condition can be used to determine whether to stop or re-
deliver event A1/A2 measurement for triggering frequency-priority-based inter-frequency
handovers.
l MLB from the serving cell has not been triggered when the
MlbBasedFreqPriHoSwitch option of the CellAlgoSwitch.FreqPriorityHoSwitch
parameter is selected.
l The eNodeB detects cells that meet the following conditions when the
LoadTriggerFreqPriHoSwitch option of the CellAlgoSwitch.FreqPriorityHoSwitch
parameter is selected:
– EutranInterFreqNCell.OverlapInd is set to YES for neighboring cells.
– The load of neighboring cells can be obtained.
– UE-number-based MLB from the neighboring cells has not been triggered.
– There are no PCI conflicts between the neighboring cells and any other cell.
l If frequency-priority-based inter-frequency handover has been enabled for an intra-
eNodeB neighboring cell, the PRB usage of the candidate neighboring cell is lower than
the CellMLB.InterFreqMlbThd parameter value of this neighboring cell.
Table 10-1 lists the conditions for starting and stopping this function.
The conditions for starting and stopping this function vary in different scenarios, but the
thresholds related to events A1 and A2 are the same.
Table 10-3 and Table 10-4 describe thresholds related to events A1 and A2, respectively.
Table 10-6 Conditions for starting and stopping frequency-priority-based blind handover
Same as measurement-based handover, blind handover is initiated when the eNodeB receives
an event A1 report.
10.2.1 Benefits
This function provides a means to transfer UEs and allows flexible networking to meet the
service steering requirements of operators.
10.2.2 Impacts
Network Impacts
None
Function Impacts
None
10.3 Requirements
10.3.1 Licenses
For FDD, the operator has purchased and activated the license for event A2-based frequency-
priority-based handovers (applying to multi-band different-coverage scenarios). There are no
license requirements for event A1-based frequency-priority-based handovers (applying to
multi-band same-coverage scenarios)
10.3.2 Software
Before activating this function, ensure that its prerequisite functions have been activated and
mutually exclusive functions have been deactivated. For detailed operations, see the relevant
feature documents.
Prerequisite Functions
None
10.3.3 Hardware
Boards
No requirements
RF Modules
No requirements
10.3.4 Others
None
Table 10-7 and Table 10-8 describe the parameters used for function activation and
optimization, respectively.
l Using counters
Observe the value of the counter listed in Table 10-9. If it has non-zero values, this
function has taken effect.
1526729484 L.HHO.InterFreq.FreqPri.ExecSuccO
ut
Monitor the counters in Table 10-10 to check the running status of this function.
1526729482 L.HHO.InterFreq.FreqPri.PrepAttOut
1526729483 L.HHO.InterFreq.FreqPri.ExecAttOut
1526729484 L.HHO.InterFreq.FreqPri.ExecSuccOut
1526730006 L.HHO.InterFddTdd.FreqPri.PrepAttOu
t
1526730007 L.HHO.InterFddTdd.FreqPri.ExecAttOu
t
1526730008 L.HHO.InterFddTdd.FreqPri.ExecSuccO
ut
11.1 Principles
The UtranSepOpMobilitySwitch option of the ENodeBAlgoSwitch.MultiOpCtrlSwitch
parameter specifies whether to enable this function.
This function is an enhancement of the handover policy selection. In the target cell or target
frequency decision phase, the eNodeB determines a handover policy with the help of this
function. Figure 11-1 shows the differences between the process of this function and the basic
handover process.
Figure 11-1 Process of Separate Mobility Policies to UTRAN for Multi PLMN
SRVCC capabilities of UTRAN cells based on PLMN and RNC configurations. Based
on the obtained SRVCC capabilities, the eNodeB determines whether to use SRVCC for
E-UTRAN to UTRAN voice service handovers. For details, see SRVCC.
l Multi-PLMN mobility policy for SI acquisition through CN-based RIM: When the
SiByRimCapCfg option of the UtranNetworkCapCfg.NetworkCapCfg parameter is
selected, the eNodeB can obtain RIM capabilities of UTRAN cells based on PLMN and
RNC configurations. For voice services, the eNodeB determines a CSFB method for
CSFB to UTRAN. For data services, the eNodeB determines a redirection method for
redirection to UTRAN. For details, see CS Fallback.
l Multi-PLMN mobility policy for ultra-flash CSFB: When the UltraFlashCsfbCapCfg
option of the UtranNetworkCapCfg.NetworkCapCfg parameter is selected, the eNodeB
can obtain ultra-flash CSFB capabilities of UTRAN cells based on PLMN and RNC
configurations. Based on the obtained ultra-flash CSFB capabilities, the eNodeB
determines whether to use ultra-flash CSFB for E-UTRAN to UTRAN CSFB. For
details, see CS Fallback.
11.2.1 Benefits
This function provides a means to transfer UEs and allows flexible networking to meet the
service requirements of different operators.
11.2.2 Impacts
Network Impacts
This function enables the eNodeB to determine the handover, RIM supporting, VoIP, ultra-
flash CSFB, and SRVCC capabilities of the UTRAN. This reduces unnecessary signaling
exchanges, and therefore reduces the number of handover attempts and failures.
Function Impacts
None
11.3 Requirements
11.3.1 Licenses
The operator has purchased and activated the license for the feature listed in the following
table.
Feature ID Feature Name Model Sales Unit
11.3.2 Software
Before activating this function, ensure that its prerequisite functions have been activated and
mutually exclusive functions have been deactivated. For detailed operations, see the relevant
feature documents.
Prerequisite Functions
Function Name Function Reference Description
Switch
11.3.3 Hardware
Base Station Models
No requirements
Boards
No requirements
RF Modules
No requirements
11.3.4 Others
None
Table 11-1 Parameters used for activation of Separate Mobility Policies to UTRAN for Multi
PLMN
Parameter Parameter Option Setting Notes
Name ID
a: The SiByRimCapCfg option of this parameter affects the CN-based RIM procedure.
The eCoordinator-based RIM procedure is not affected by this option.
12.1 Principles
The GeranSepOpMobilitySwitch option of the CellAlgoSwitch.HoAllowedSwitch
parameter specifies whether to enable this function.
This function is an enhancement of the handover policy selection. In the target cell or target
frequency decision phase, the eNodeB determines a handover policy with the help of this
function. Figure 12-1 shows the differences between the process of this function and the basic
handover process.
Figure 12-1 Process of Separate Mobility Policies to GERAN for Multi PLMN
l Multi-PLMN mobility policy for SRVCC: When the SrvccCapCfg option of the
GeranNetworkCapCfg.NetworkCapCfg parameter is selected, the eNodeB can obtain
SRVCC capabilities of GERAN cells based on PLMN and LAC configurations. Based
on the obtained SRVCC capabilities, the eNodeB determines whether to use SRVCC for
E-UTRAN to GERAN voice service handovers. For details, see SRVCC.
12.2.1 Benefits
This function provides a means to transfer UEs and allows flexible networking to meet the
service requirements of different operators.
12.2.2 Impacts
Network Impacts
This function enables the eNodeB to determine the RIM supporting, ultra-flash CSFB, and
SRVCC capabilities of the GERAN. This reduces unnecessary signaling exchanges, and
therefore reduces the number of handover attempts and failures.
Function Impacts
None
12.3 Requirements
12.3.1 Licenses
The operator has purchased and activated the licenses for the features listed in the following
table.
12.3.2 Software
Before activating this function, ensure that its prerequisite functions have been activated and
mutually exclusive functions have been deactivated. For detailed operations, see the relevant
feature documents.
Prerequisite Functions
RAT Function Function Reference Description
Name Switch
12.3.3 Hardware
Boards
No requirements
RF Modules
No requirements
12.3.4 Others
None
Table 12-1 Parameters used for activation of Separate Mobility Policies to GERAN for Multi
PLMN
a: The SiByRimCapCfg option of this parameter affects the CN-based RIM procedure.
The eCoordinator-based RIM procedure is not affected by this option.
13 Parameters
IntraRat FreqPriI MOD None None Meaning: Indicates the time within which the eNodeB
HoCom FHoWai INTRA waits for measurement reports for frequency-priority-
m tingTim RATHO based inter-frequency handovers. The value 0
er COMM indicates that the eNodeB handles a measurement
LST report upon receiving it. If this parameter is set to a
INTRA value greater than 0, the eNodeB waits for other
RATHO measurement reports after receiving any measurement
COMM report for a frequency-priority-based inter-frequency
handover. This parameter applies only to LTE FDD
and LTE TDD.
GUI Value Range: 0~30
Unit: 100ms
Actual Value Range: 0~30
Default Value: 0
EutranIn MeasPri ADD None None Meaning: Indicates the measurement priority of the
terNFre orityFor EUTRA frequency for frequency-priority-based handovers.
q FreqPri NINTE Before delivering frequencies to measure for
Ho RNFRE frequency-priority-based handovers, the eNodeB
Q selects frequencies based on the settings of this
MOD parameter. It preferentially selects high-priority
EUTRA frequencies. The larger the value of this parameter, the
NINTE higher the priority level. This parameter applies only
RNFRE to LTE FDD and LTE TDD.
Q GUI Value Range: 0~16
LST Unit: None
EUTRA Actual Value Range: 0~16
NINTE
RNFRE Default Value: 0
Q
InterRat A2Base ADD LOFD-0 PS Inter- Meaning: Indicates the QCI-specific quantity to
HoCom dInterRa INTER 01019/ RAT determine whether to trigger inter-RAT measurements
mGroup tHoTrig RATHO TDLOF Mobility or blind handovers based on inter-RAT event A2. If
Quan COMM D-00101 between this parameter is set to BOTH, the eNodeB determines
GROUP 9 E- whether to trigger inter-RAT measurements or blind
MOD LOFD-0 UTRAN handovers based on either RSRP or RSRQ. If this
INTER 01020/ and parameter is set to RSRP, the eNodeB determines
RATHO TDLOF UTRAN whether to trigger inter-RAT measurements or blind
COMM D-00102 PS Inter- handovers based on RSRP. If this parameter is set to
GROUP 0 RAT RSRQ, the eNodeB determines whether to trigger
Mobility inter-RAT measurements or blind handovers based on
LST LOFD-0 RSRQ. This parameter is valid only if the
INTER 01021/ between
E- InterRatHoA1A2TrigQuan parameter is set to BOTH
RATHO TDLOF in the InterRatHoComm MO. This parameter applies
COMM D-00102 UTRAN
and only to LTE FDD and LTE TDD.
GROUP 1
GERAN GUI Value Range: BOTH, RSRP, RSRQ
LOFD-0
01022/ PS Inter- Unit: None
TDLOF RAT Actual Value Range: BOTH, RSRP, RSRQ
D-00102 Mobility
between Default Value: BOTH
2
E-
LOFD-0 UTRAN
01023/ and
TDLOF CDMA2
D-00102 000
3
SRVCC
to
UTRAN
SRVCC
to
GERAN
CnOper InterRat ADD LOFD-0 PS Inter- Meaning: Indicates the offset to the
atorQciP A2Rsrp CNOPE 01019/ RAT InterRatHoA2ThdRsrp parameter value. The RSRP
ara ThldOff RATOR TDLOF Mobility threshold for inter-RAT measurement event A2 is
set QCIPA D-00101 between obtained by adding up this offset, the
RA 9 E- InterRatHoA2ThdRsrp
MOD LOFD-0 UTRAN (InterRatHoCommGroup.InterRatHoA2ThdRsrp)
CNOPE 01020/ and parameter value , and the UtranA2ThdRsrpOffset
RATOR TDLOF UTRAN (CnOperatorHoCfg.UtranA2ThdRsrpOffset) or
QCIPA D-00102 PS Inter- GeranA2ThdRsrpOffset
RA 0 RAT (CnOperatorHoCfg.GeranA2ThdRsrpOffset)
Mobility parameter value . This parameter applies only to LTE
LST FDD and LTE TDD.
CNOPE between
RATOR E- GUI Value Range: -20~20
QCIPA UTRAN Unit: dBm
RA and
GERAN Actual Value Range: -20~20
Default Value: 0
EutranIn DlEarfc ADD LBFD-0 Coverag Meaning: Indicates the DL EARFCN of the
terNFre n EUTRA 0201802 e Based neighboring cell on the neighboring E-UTRAN
q NINTE / Inter- frequency. For details, see the 3GPP TS 36.104.
RNFRE TDLBF frequenc GUI Value Range: 0~68585,229376~229575
Q D-00201 y
802 Handov Unit: None
LST
EUTRA LBFD-0 er Actual Value Range: 0~68585,229376~229575
NINTE 0201803 Cell Default Value: None
RNFRE / Selectio
Q TDLBF n and
MOD D-00201 Re-
EUTRA 803 selection
NINTE LBFD-0 Distance
RNFRE 0201804 Based
Q / Inter-
RMV TDLBF frequenc
CELLE D-00201 y
UTRAN 804 Handov
INTER LBFD-0 er
NFREQ 0201805 Service
RMV / Based
EUTRA TDLBF Inter-
NINTE D-00201 frequenc
RNFRE 805 y
Q LBFD-1 Handov
31111/ er
TDLBF Mobility
D-00105 between
0 LTE
MLBFD TDD
-120002 and LTE
37 FDD
Cell
Selectio
n and
Re-
selection
EutranIn MeasBa ADD LBFD-0 Coverag Meaning: Indicates the measurement bandwidth of the
terNFre ndWidth EUTRA 0201802 e Based inter-frequency neighboring cell on the frequency. The
q NINTE / Inter- setting of this parameter depends on the bandwidth
RNFRE TDLBF frequenc configuration of the cell. In E-UTRAN, a cell
Q D-00201 y bandwidth is also expressed in units of resource
MOD 802 Handov blocks (RBs). Cell bandwidths 1.4 MHz, 3 MHz, 5
EUTRA LBFD-0 er MHz, 10 MHz, 15 MHz, and 20 MHz correspond to 6
NINTE 0201804 Distance RBs, 15 RBs, 25 RBs, 50 RBs, 75 RBs, and 100 RBs,
RNFRE / Based respectively. For details, see 3GPP TS 36.331. This
Q TDLBF Inter- parameter applies only to LTE FDD and LTE TDD.
LST D-00201 frequenc GUI Value Range: MBW6(1.4M), MBW15(3M),
EUTRA 804 y MBW25(5M), MBW50(10M), MBW75(15M),
NINTE LBFD-0 Handov MBW100(20M)
RNFRE 0201805 er Unit: None
Q / Service Actual Value Range: MBW6, MBW15, MBW25,
TDLBF Based MBW50, MBW75, MBW100
D-00201 Inter-
805 frequenc Default Value: None
LEOFD- y
111306/ Handov
TDLOF er
D-12020 Breathin
5 g Pilot
EutranIn QoffsetF ADD LBFD-0 Coverag Meaning: Indicates the frequency-specific offset for
terNFre reqConn EUTRA 0201802 e Based the neighboring E-UTRAN frequency that applies to
q NINTE / Inter- UEs in connected mode. It is contained in the event
RNFRE TDLBF frequenc A3/A4/A5 measurement configuration and delivered
Q D-00201 y to UEs in connected mode. The offset affects the
MOD 802 Handov probability of reporting events A3, A4, and A5. For
EUTRA LBFD-0 er details, see 3GPP TS 36.331. This parameter applies
NINTE 0201804 Distance only to LTE FDD and LTE TDD.
RNFRE / Based GUI Value Range: dB-24(-24dB), dB-22(-22dB),
Q TDLBF Inter- dB-20(-20dB), dB-18(-18dB), dB-16(-16dB),
LST D-00201 frequenc dB-14(-14dB), dB-12(-12dB), dB-10(-10dB),
EUTRA 804 y dB-8(-8dB), dB-6(-6dB), dB-5(-5dB), dB-4(-4dB),
NINTE LBFD-0 Handov dB-3(-3dB), dB-2(-2dB), dB-1(-1dB), dB0(0dB),
RNFRE 0201805 er dB1(1dB), dB2(2dB), dB3(3dB), dB4(4dB),
Q / Service dB5(5dB), dB6(6dB), dB8(8dB), dB10(10dB),
TDLBF Based dB12(12dB), dB14(14dB), dB16(16dB), dB18(18dB),
D-00201 Inter- dB20(20dB), dB22(22dB), dB24(24dB)
805 frequenc Unit: dB
y Actual Value Range: dB-24, dB-22, dB-20, dB-18,
Handov dB-16, dB-14, dB-12, dB-10, dB-8, dB-6, dB-5, dB-4,
er dB-3, dB-2, dB-1, dB0, dB1, dB2, dB3, dB4, dB5,
dB6, dB8, dB10, dB12, dB14, dB16, dB18, dB20,
dB22, dB24
Default Value: dB0(0dB)
Band 9:
Normal UARFCNs: [9237-9387]
Special UARFCNs: none
The UARFCN range in each TDD frequency band is
shown as follows:
Band 1:
Normal UARFCNs: [9500-9600] and [10050-10125]
Special UARFCNs: none
Band 2:
Normal UARFCNs: [9250-9550] and [9650-9950]
Special UARFCNs: none
Band 3:
Normal UARFCNs: [9550-9650]
Special UARFCNs: none
Band 4:
Normal UARFCNs: [12850-13100]
Special UARFCNs: (2112, 2137, 2162, 2187, 2212,
2237, 2262, 2287, 2312, 2337)
Band 5:
Normal UARFCNs: [11500-12000]
Special UARFCNs: none
Band 6:
Normal UARFCNs: [9400-9600]
Special UARFCNs: none
For details, see 3GPP TS 25.104 and 3GPP TS
25.105. This parameter applies only to LTE FDD and
LTE TDD.
GUI Value Range: 0~16383
Unit: None
Actual Value Range: 0~16383
Default Value: None
UtranNF OffsetFr ADD LOFD-0 PS Inter- Meaning: Indicates the frequency offset of the cell on
req eq UTRAN 01019/ RAT the UTRAN frequency. It determines the probability
NFREQ TDLOF Mobility of triggering measurement reports for events B1 and
MOD D-00101 between B2. For details, see 3GPP TS 36.331. This parameter
UTRAN 9 E- applies only to LTE FDD and LTE TDD.
NFREQ LOFD-0 UTRAN GUI Value Range: -15~15
01022/ and
LST UTRAN Unit: dB
UTRAN TDLOF
D-00102 SRVCC Actual Value Range: -15~15
NFREQ
2 to Default Value: 0
LOFD-0 UTRAN
01033/ CS
TDLOF Fallback
D-00103 to
3 UTRAN
LOFD-0 Flash
01052/ CS
TDLOF Fallback
D-00105 to
2 UTRAN
LBFD-0 Mobility
02018/ Manage
TDLBF ment
D-00201
8
GeranNf Starting ADD LBFD-0 Cell Meaning: Indicates the first ARFCN in the GERAN
reqGrou Arfcn GERAN 0201803 Selectio carrier frequency group. If the GERAN ARFCN is not
p NFREQ / n and between 512 and 810, one ARFCN can only be in one
GROUP TDLBF Re- frequency band. For details, see 3GPP TS 45.005.
MOD D-00201 selection This parameter applies only to LTE FDD and LTE
GERAN 803 PS Inter- TDD.
NFREQ LOFD-0 RAT GUI Value Range: 0~1023
GROUP 01020/ Mobility Unit: None
LST TDLOF between
D-00102 E- Actual Value Range: 0~1023
GERAN
NFREQ 0 UTRAN Default Value: None
GROUP LBFD-0 and
02018 GERAN
Mobility
Manage
ment
GeranNf BandInd ADD LBFD-0 Cell Meaning: Indicates the GERAN band indicator. If the
reqGrou icator GERAN 0201803 Selectio GERAN ARFCN is between 512 and 810, this
p NFREQ / n and parameter indicates whether the GERAN ARFCN is
GROUP TDLBF Re- in the 1800 MHz band or the 1900 MHz band. If the
MOD D-00201 selection GERAN ARFCN is not in either band, this parameter
GERAN 803 PS Inter- does not take effect and can be set to either value and
NFREQ LOFD-0 RAT one ARFCN can only be in one frequency band. For
GROUP 01020/ Mobility details, see 3GPP TS 45.005. This parameter applies
TDLOF between only to LTE FDD and LTE TDD.
LST
GERAN D-00102 E- GUI Value Range: GSM_dcs1800, GSM_pcs1900
NFREQ 0 UTRAN Unit: None
GROUP and
GERAN Actual Value Range: GSM_dcs1800, GSM_pcs1900
Default Value: None
GeranNf GeranAr ADD LBFD-0 Cell Meaning: Specifies the ARFCN of the GERAN
reqGrou fcn GERAN 0201803 Selectio BCCH. If the GERAN ARFCN value is not between
pArfcn NFREQ / n and 512 and 810, one ARFCN can only in one frequency
GROUP TDLBF Re- band. For details about this parameter, see 3GPP TS
ARFCN D-00201 selection 45.005. This parameter applies only to LTE FDD and
LST 803 PS Inter- LTE TDD.
GERAN LOFD-0 RAT GUI Value Range: 0~1023
NFREQ 01020/ Mobility Unit: None
GROUP TDLOF between
ARFCN D-00102 E- Actual Value Range: 0~1023
GeranNf OffsetFr ADD LOFD-0 PS Inter- Meaning: Indicates the frequency offset of the group
reqGrou eq GERAN 01020/ RAT of neighboring GERAN carrier frequencies. This
p NFREQ TDLOF Mobility parameter is used in the decision of the UE to send
GROUP D-00102 between measurement reports for inter-RAT handovers. For
MOD 0 E- details, see 3GPP TS 36.331. This parameter applies
GERAN LOFD-0 UTRAN only to LTE FDD and LTE TDD.
NFREQ 01023/ and GUI Value Range: -15~15
GROUP TDLOF GERAN
Unit: dB
LST D-00102 SRVCC
3 to Actual Value Range: -15~15
GERAN
NFREQ LOFD-0 GERAN Default Value: 0
GROUP 01034/ CS
TDLOF Fallback
D-00103 to
4 GERAN
LOFD-0 Flash
01053/ CS
TDLOF Fallback
D-00105 to
3 GERAN
LBFD-0 Mobility
02018/ Manage
TDLBF ment
D-00201
8
ServiceBasedInterFreqHoSwitch, UlQualityInterFreq-
HoSwitch, CSFBLoadInfoSwitch,
Cdma1XrttEcsfbSwitch, EmcBlindHoA1Switch,
EmcInterFreqBlindHoSwitch, EPlmnSwitch,
ServiceReqInterFreqHoSwitch,
VoipHoControlSwitch, UtranUltraFlashCsfbSwitch,
GeranUltraFlashCsfbSwitch, RatLayerSwitch,
ServiceBasedMultiFreqHoSwitch, SrvccRatSteeringS-
witch, PsRatSteeringSwitch
Default Value: IntraFreqCoverHoSwitch:On,
InterFreqCoverHoSwitch:On,
Cdma1xRttCsfbSwitch:Off, UtranServiceHoS-
witch:Off, GeranServiceHoSwitch:Off,
UlQualityInterRATHoSwitch:Off,
InterPlmnHoSwitch:Off, ServiceBasedInterFreqHoS-
witch:Off, UlQualityInterFreqHoSwitch:Off,
CSFBLoadInfoSwitch:Off,
Cdma1XrttEcsfbSwitch:Off,
EmcBlindHoA1Switch:Off, EmcInterFreqBlindHoS-
witch:Off, EPlmnSwitch:Off, ServiceReqInterFreq-
HoSwitch:Off, VoipHoControlSwitch:Off,
UtranUltraFlashCsfbSwitch:Off,
GeranUltraFlashCsfbSwitch:Off, RatLayerSwitch:Off,
ServiceBasedMultiFreqHoSwitch:Off,
SrvccRatSteeringSwitch:Off,
PsRatSteeringSwitch:Off
Unit: None
Actual Value Range: FixedMeasObjIDSwitch,
VoipMeasFreqPriSwitch, PsMeasFreqPriSwitch
Default Value: FixedMeasObjIDSwitch:Off,
VoipMeasFreqPriSwitch:Off,
PsMeasFreqPriSwitch:Off
EutranIn ConnFre ADD LBFD-0 Coverag Meaning: Indicates the frequency priority based on
terNFre qPriority EUTRA 0201802 e Based which the eNodeB selects a target frequency for blind
q NINTE / Inter- redirection or contains a frequency in a measurement
RNFRE TDLBF frequenc configuration. If a blind redirection is triggered and
Q D-00201 y the target neighboring cell is not specified, the
MOD 802 Handov eNodeB selects a target frequency based on this
EUTRA LBFD-0 er priority. If a measurement configuration is to be
NINTE 0201804 Distance delivered, the eNodeB preferentially delivers a
RNFRE / Based frequency with the highest priority. If this priority is
Q TDLBF Inter- set to 0 for a frequency, this frequency is not selected
D-00201 frequenc as the target frequency for a blind redirection. A larger
LST value indicates a higher priority. This parameter
EUTRA 804 y
Handov applies only to LTE FDD and LTE TDD.
NINTE
RNFRE er GUI Value Range: 0~16
Q Unit: None
Actual Value Range: 0~16
Default Value: 0
EutranIn MeasFre ADD LBFD-0 Coverag Meaning: Indicates the frequency measurement
terNFre qPriority EUTRA 0201802 e Based priority. A larger value indicates a higher priority. If
q NINTE / Inter- the CovBasedInterfreqHoMode parameter is set to
RNFRE TDLBF frequenc BASEDONSIGNALSTRENGTH or
Q D-00201 y BASEDONFREQPRIORITY or the
MOD 802 Handov FixedMeasObjIDSwitch option of the
EUTRA LBFD-0 er MultiFreqPriControlSwitch parameter is selected, the
NINTE 0201804 Distance eNodeB delivers frequencies for measurement based
RNFRE / Based on the priority specified by this parameter in inter-
Q TDLBF Inter- frequency handovers except service- and service-
D-00201 frequenc request-based inter-frequency handovers. If this
LST parameter is set to 0, the measurement priority of the
EUTRA 804 y
Handov neighboring E-UTRA frequency is the lowest and this
NINTE LBFD-0 frequency can still be delivered for measurement. This
RNFRE 0201805 er
parameter applies only to LTE FDD and LTE TDD.
Q / Service
TDLBF Based GUI Value Range: 0~16
D-00201 Inter- Unit: None
805 frequenc Actual Value Range: 0~16
y
Handov Default Value: 0
er
CellAlg MultiCn MOD LBFD-0 Mobility Meaning: Indicates whether to enable the policy of
oSwitch ConnFre CELLA 02018/ Manage frequency priority for the connected mode in
qPriSw LGOSW TDLBF ment handovers. If this parameter is set to ON, the
ITCH D-00201 Coverag frequency priority for the connected mode associated
LST 8 e Based with the ConnFreqPriority parameter in the
CELLA LBFD-0 Inter- RatFreqPriorityGroup MO takes effect and the
LGOSW 0201802 frequenc frequency priority policy in handovers is supported in
ITCH / y RAN sharing scenarios. This option applies only to
TDLBF Handov LTE FDD and LTE TDD.
D-00201 er GUI Value Range: OFF(Off), ON(On)
802 Unit: None
Actual Value Range: OFF, ON
Default Value: OFF(Off)
CellOp RatFreq ADD LBFD-0 Mobility Meaning: Indicates the eNodeB-level inter-frequency
Priority CELLO 02018/ Manage or inter-RAT frequency priority group ID for an
GroupId P TDLBF ment operator. This option applies only to LTE FDD and
MOD D-00201 Coverag LTE TDD.
CELLO 8 e Based GUI Value Range: 0~255,65535
P LBFD-0 Inter- Unit: None
LST 0201802 frequenc
/ y Actual Value Range: 0~255,65535
CELLO
P TDLBF Handov Default Value: 65535
D-00201 er
802
RatFreq ConnFre ADD LBFD-0 Mobility Meaning: Indicates the frequency priority for the
Priority qPriority RATFR 02018/ Manage connected mode. Operators can configure different
Group EQPRI TDLBF ment frequency priorities for the connected mode by
ORITY D-00201 Coverag PLMN. This parameter applies only to LTE FDD and
GROUP 8 e Based LTE TDD.
MOD LBFD-0 Inter- GUI Value Range: 0~16
RATFR 0201802 frequenc Unit: None
EQPRI / y
ORITY TDLBF Handov Actual Value Range: 0~16
GROUP D-00201 er Default Value: 0
LST 802
RATFR
EQPRI
ORITY
GROUP
UtranNF ConnFre ADD LOFD-0 PS Inter- Meaning: Indicates the frequency priority based on
req qPriority UTRAN 01019/ RAT which the eNodeB selects a target frequency for blind
NFREQ TDLOF Mobility redirection or contains a frequency in a measurement
MOD D-00101 between configuration. If a blind redirection is triggered and
UTRAN 9 E- the target neighboring cell is not specified, the
NFREQ LBFD-0 UTRAN eNodeB selects a target frequency based on this
0201803 and priority. If a measurement configuration is to be
LST UTRAN delivered, the eNodeB preferentially delivers a
UTRAN /
TDLBF Cell frequency with the highest priority. If this priority is
NFREQ set to 0 for a frequency, this frequency is not selected
D-00201 Selectio
803 n and as the target frequency for a blind redirection. A larger
Re- value indicates a higher priority. This parameter
TDLOF applies only to LTE FDD and LTE TDD.
D-00102 selection
2 SRVCC GUI Value Range: 0~8
TDLOF to Unit: None
D-00103 UTRAN Actual Value Range: 0~8
3 CS Default Value: 0
TDLOF Fallback
D-00105 to
2 UTRAN
LOFD-0 Flash
01043/ CS
TDLOF Fallback
D-00104 to
3 UTRAN
LOFD-0 Service
01072/ based
TDLOF Inter-
D-00107 RAT
2 handove
r to
TDLBF UTRAN
D-00201
8 Distance
based
Inter-
RAT
handove
r to
UTRAN
Mobility
Manage
ment
GeranNf ConnFre ADD LOFD-0 PS Inter- Meaning: Indicates the frequency group priority used
reqGrou qPriority GERAN 01020/ RAT in selecting target groups for blind redirection and in
p NFREQ TDLOF Mobility delivering groups to measure. During blind
GROUP D-00102 between redirection, if no neighboring cell has been configured
MOD 0 E- to be suitable for blind handovers, the eNodeB selects
GERAN LOFD-0 UTRAN a target frequency group based on the priorities
NFREQ 01023/ and specified by this parameter. If this parameter is set to 0
GROUP TDLOF GERAN for a group, the eNodeB does not select this group for
D-00102 SRVCC blind redirection. During measurement configuration,
LST the eNodeB preferentially delivers the frequency
GERAN 3 to
GERAN group with the highest priority specified by this
NFREQ LOFD-0 parameter. The larger the parameter value, the higher
GROUP 01034/ CS the priority. This parameter applies only to LTE FDD
TDLOF Fallback and LTE TDD.
D-00103 to
4 GERAN GUI Value Range: 0~8
LOFD-0 Flash Unit: None
01053/ CS Actual Value Range: 0~8
TDLOF Fallback Default Value: 0
D-00105 to
3 GERAN
LBFD-0 Mobility
02018/ Manage
TDLBF ment
D-00201
8
CellUe MaxNon MOD LBFD-0 Coverag Meaning: Indicates the maximum number of total
MeasCo IntraMe CELLU 0201802 e Based inter-frequency and inter-RAT measurement objects
ntrolCfg asObjNu EMEAS / Inter- that can be contained in the measurement control
m CONTR TDLBF frequenc messages delivered for UEs in RRC_CONNECTED
OLCFG D-00201 y state. This parameter applies only to LTE FDD and
LST 802 Handov LTE TDD.
CELLU LBFD-0 er GUI Value Range: 1~32
EMEAS 0201804 Distance Unit: None
CONTR / Based
OLCFG Inter- Actual Value Range: 1~32
TDLBF
D-00201 frequenc Default Value: 7
804 y
Handov
LBFD-0
er
0201805
/ Service
TDLBF Based
D-00201 Inter-
805 frequenc
y
LBFD-1 Handov
31111/ er
TDLBF
D-00105 Mobility
0 between
LTE
LOFD-0 TDD
01019/ and LTE
TDLOF FDD
D-00101
PS Inter-
9
RAT
TDLOF Mobility
D-00102 between
2 E-
TDLOF UTRAN
D-00104 and
3 UTRAN
TDLOF SRVCC
D-00107 to
2 UTRAN
Service
LOFD-0
based
01020/
Inter-
TDLOF
RAT
D-00102
handove
0
r to
TDLOF UTRAN
D-00102 Distance
3 based
Inter-
RAT
handove
r to
UTRAN
PS Inter-
RAT
Mobility
between
E-
UTRAN
and
GERAN
SRVCC
to
GERAN
CellUe MaxEutr MOD LBFD-0 Coverag Meaning: Indicates the maximum number of E-
MeasCo anFddM CELLU 0201802 e Based UTRAN FDD frequencies (excluding the frequency
ntrolCfg easFreq EMEAS / Inter- on which the serving cell operates) that can be
Num CONTR TDLBF frequenc contained in the measurement control messages
OLCFG D-00201 y delivered to UEs in the RRC_CONNECTED state.
LST 802 Handov This parameter applies only to LTE FDD and LTE
CELLU LBFD-0 er TDD.
EMEAS 0201804 Distance GUI Value Range: 1~16
CONTR / Based Unit: None
OLCFG TDLBF Inter-
D-00201 frequenc Actual Value Range: 1~16
804 y Default Value: 3
LBFD-0 Handov
0201805 er
/ Service
TDLBF Based
D-00201 Inter-
805 frequenc
LBFD-1 y
31111/ Handov
TDLBF er
D-00105 Mobility
0 between
LTE
TDD
and LTE
FDD
CellUe MaxEutr MOD LBFD-0 Coverag Meaning: Indicates the maximum number of E-
MeasCo anTddM CELLU 0201802 e Based UTRAN TDD frequencies (excluding the frequency
ntrolCfg easFreq EMEAS / Inter- on which the serving cell works) that can be contained
Num CONTR TDLBF frequenc in the measurement control messages delivered to UEs
OLCFG D-00201 y in RRC_CONNECTED state. This parameter applies
LST 802 Handov only to LTE FDD and LTE TDD.
CELLU LBFD-0 er GUI Value Range: 1~16
EMEAS 0201804 Distance Unit: None
CONTR / Based
OLCFG TDLBF Inter- Actual Value Range: 1~16
D-00201 frequenc Default Value: 3
804 y
LBFD-0 Handov
0201805 er
/ Service
TDLBF Based
D-00201 Inter-
805 frequenc
LBFD-1 y
31111/ Handov
TDLBF er
D-00105 Mobility
0 between
LTE
TDD
and LTE
FDD
CellUe MaxUtr MOD LOFD-0 PS Inter- Meaning: Indicates the maximum number of UTRAN
MeasCo anFddM CELLU 01019/ RAT FDD frequencies that can be contained in the
ntrolCfg easFreq EMEAS TDLOF Mobility measurement control messages delivered for UEs in
Num CONTR D-00101 between the RRC_CONNECTED state. This parameter applies
OLCFG 9 E- only to LTE FDD and LTE TDD.
LST LOFD-0 UTRAN GUI Value Range: 1~16
CELLU 01022/ and
UTRAN Unit: None
EMEAS TDLOF
CONTR D-00102 SRVCC Actual Value Range: 1~16
OLCFG 2 to Default Value: 3
LOFD-0 UTRAN
01043/ Service
TDLOF based
D-00104 Inter-
3 RAT
LOFD-0 handove
01072/ r to
TDLOF UTRAN
D-00107 Distance
2 based
LOFD-0 Inter-
01033/ RAT
TDLOF handove
D-00103 r to
3 UTRAN
LBFD-0 CS
02018/ Fallback
TDLBF to
D-00201 UTRAN
8 Mobility
Manage
ment
CellUe MaxUtr MOD LOFD-0 PS Inter- Meaning: Indicates the maximum number of UTRAN
MeasCo anTddM CELLU 01019/ RAT TDD frequencies that can be contained in the
ntrolCfg easFreq EMEAS TDLOF Mobility measurement control messages delivered for UEs in
Num CONTR D-00101 between the RRC_CONNECTED state. This parameter applies
OLCFG 9 E- only to LTE TDD.
LST LOFD-0 UTRAN GUI Value Range: 1~16
CELLU 01022/ and
UTRAN Unit: None
EMEAS TDLOF
CONTR D-00102 SRVCC Actual Value Range: 1~16
OLCFG 2 to Default Value: 3
LOFD-0 UTRAN
01043/ Service
TDLOF based
D-00104 Inter-
3 RAT
LOFD-0 handove
01072/ r to
TDLOF UTRAN
D-00107 Distance
2 based
LOFD-0 Inter-
01033/ RAT
TDLOF handove
D-00103 r to
3 UTRAN
LBFD-0 CS
02018/ Fallback
TDLBF to
D-00201 UTRAN
8 Mobility
Manage
ment
CellUe MaxGer MOD LOFD-0 PS Inter- Meaning: Indicates the maximum number of GERAN
MeasCo anMeas CELLU 01020/ RAT frequencies that can be contained in the measurement
ntrolCfg FreqNu EMEAS TDLOF Mobility control messages delivered for UEs in
m CONTR D-00102 between RRC_CONNECTED state. This parameter applies
OLCFG 0 E- only to LTE FDD and LTE TDD.
LST LOFD-0 UTRAN GUI Value Range: 1~64
CELLU 01023/ and
GERAN Unit: None
EMEAS TDLOF
CONTR D-00102 SRVCC Actual Value Range: 1~64
OLCFG 3 to Default Value: 32
LOFD-0 GERAN
01046/ Service
TDLOF based
D-00104 Inter-
6 RAT
LOFD-0 handove
01073/ r to
TDLOF GERAN
D-00107 Distance
3 based
LOFD-0 Inter-
01034/ RAT
TDLOF handove
D-00103 r to
4 GERAN
LBFD-0 CS
02018/ Fallback
TDLBF to
D-00201 GERAN
8 Mobility
Manage
ment
LOAD_COVERAGE_MEAS_DECOUPLE_SW(Loa
d Coverage Meas Decouple Switch),
CSFB_MEAS_DEL_ACT_PCI_MEAS_SW(Active
PCI Meas Del During CSFB Meas Sw)
Unit: None
Actual Value Range:
GSM_MEAS_DEL_INTERFREQ_SW,
MEAS_OBJ_PREEMPT_SW,
CSFB_MEAS_DEL_INTERFREQ_SW,
GSM_MEAS_RECOVER_INTERFREQ_SW,
SINR_MEAS_CONFIG_SW,
LOAD_COVERAGE_MEAS_DECOUPLE_SW,
CSFB_MEAS_DEL_ACT_PCI_MEAS_SW
Default Value:
GSM_MEAS_DEL_INTERFREQ_SW:Off,
MEAS_OBJ_PREEMPT_SW:Off,
CSFB_MEAS_DEL_INTERFREQ_SW:Off,
GSM_MEAS_RECOVER_INTERFREQ_SW:Off,
SINR_MEAS_CONFIG_SW:Off,
LOAD_COVERAGE_MEAS_DECOUPLE_SW:Off,
CSFB_MEAS_DEL_ACT_PCI_MEAS_SW:Off
EutranIn CellIndi ADD LBFD-0 Coverag Meaning: Indicates the cell individual offset for the
terFreq vidualOf EUTRA 0201802 e Based inter-frequency neighboring cell. It affects the
NCell fset NINTE / Inter- probability of triggering inter-frequency measurement
RFREQ TDLBF frequenc reports. A larger value of this parameter indicates a
NCELL D-00201 y higher probability. For details, see 3GPP TS 36.331.
MOD 802 Handov This parameter applies only to LTE FDD and LTE
EUTRA LBFD-0 er TDD.
NINTE 0201804 Distance GUI Value Range: dB-24(-24dB), dB-22(-22dB),
RFREQ / Based dB-20(-20dB), dB-18(-18dB), dB-16(-16dB),
NCELL TDLBF Inter- dB-14(-14dB), dB-12(-12dB), dB-10(-10dB),
LST D-00201 frequenc dB-8(-8dB), dB-6(-6dB), dB-5(-5dB), dB-4(-4dB),
EUTRA 804 y dB-3(-3dB), dB-2(-2dB), dB-1(-1dB), dB0(0dB),
NINTE LBFD-0 Handov dB1(1dB), dB2(2dB), dB3(3dB), dB4(4dB),
RFREQ 0201805 er dB5(5dB), dB6(6dB), dB8(8dB), dB10(10dB),
NCELL / Service dB12(12dB), dB14(14dB), dB16(16dB), dB18(18dB),
TDLBF Based dB20(20dB), dB22(22dB), dB24(24dB)
D-00201 Inter- Unit: dB
805 frequenc Actual Value Range: dB-24, dB-22, dB-20, dB-18,
y dB-16, dB-14, dB-12, dB-10, dB-8, dB-6, dB-5, dB-4,
Handov dB-3, dB-2, dB-1, dB0, dB1, dB2, dB3, dB4, dB5,
er dB6, dB8, dB10, dB12, dB14, dB16, dB18, dB20,
dB22, dB24
Default Value: dB0(0dB)
EutranIn CellMea ADD LBFD-0 Coverag Meaning: Indicates the priority of measurement on the
terFreq sPriority EUTRA 0201802 e Based inter-frequency neighboring cell. The eNodeB
NCell NINTE / Inter- preferentially contains the information about a
RFREQ TDLBF frequenc neighboring cell with this priority set to
NCELL D-00201 y HIGH_PRIORITY while delivering a measurement
MOD 802 Handov configuration. This parameter applies only to LTE
EUTRA LBFD-0 er FDD and LTE TDD.
NINTE 0201804 Distance GUI Value Range: LOW_PRIORITY(Low Priority),
RFREQ / Based HIGH_PRIORITY(High Priority)
NCELL TDLBF Inter- Unit: None
LST D-00201 frequenc
804 y Actual Value Range: LOW_PRIORITY,
EUTRA HIGH_PRIORITY
NINTE LBFD-0 Handov
RFREQ 0201805 er Default Value: LOW_PRIORITY(Low Priority)
NCELL / Service
TDLBF Based
D-00201 Inter-
805 frequenc
LBFD-1 y
31111/ Handov
TDLBF er
D-00105 Mobility
0 between
LBFD-0 LTE
0201803 TDD
/ and LTE
TDLBF FDD
D-00201 Cell
803 Selectio
n and
Re-
selection
UtranN NCellM ADD LOFD-0 Inter- Meaning: Indicates the measurement priority of the
Cell easPriori UTRAN 02002/ RAT neighboring UTRAN cell. A larger value indicates a
ty NCELL TDLOF ANR higher priority. The measurement priorities can be
MOD D-00200 SRVCC periodically and automatically arranged based on the
UTRAN 2 to number of times that each neighboring UTRAN cell is
NCELL LOFD-0 UTRAN measured. The neighboring UTRAN cells for UTRAN
01022/ measurement control, UTRAN flash blind
DSP CS redirections, and UTRAN flash-CSFB-based blind
UTRAN TDLOF Fallback
D-00102 redirections can be selected based on the measurement
EXTEN to priorities of neighboring UTRAN cells. This
DEDNC 2 UTRAN parameter applies only to LTE FDD and LTE TDD.
ELL LOFD-0 Flash
01033/ GUI Value Range: 0~128
LST CS
UTRAN TDLOF Fallback Unit: None
NCELL D-00103 to Actual Value Range: 0~128
3 UTRAN Default Value: 0
LOFD-0 PS Inter-
01052/ RAT
TDLOF Mobility
D-00105 between
2 E-
LOFD-0 UTRAN
01019/ and
TDLOF UTRAN
D-00101 Mobility
9 Manage
LBFD-0 ment
02018/ Service
TDLBF based
D-00201 Inter-
8 RAT
LOFD-0 handove
01043/ r to
TDLOF UTRAN
D-00104 Distance
3 based
LOFD-0 Inter-
01072/ RAT
TDLOF handove
D-00107 r to
2 UTRAN
UtranN CellMea ADD LOFD-0 PS Inter- Meaning: Indicates the priority of measurement on the
Cell sPriority UTRAN 01019/ RAT neighboring UTRAN cell. The eNodeB preferentially
NCELL TDLOF Mobility contains the information about a neighboring cell with
MOD D-00101 between this priority set to HIGH_PRIORITY while delivering
UTRAN 9 E- a measurement configuration. This parameter applies
NCELL LOFD-0 UTRAN only to LTE FDD and LTE TDD.
01022/ and GUI Value Range: LOW_PRIORITY(Low Priority),
LST UTRAN
UTRAN TDLOF HIGH_PRIORITY(High Priority)
NCELL D-00102 SRVCC Unit: None
2 to
UTRAN Actual Value Range: LOW_PRIORITY,
LOFD-0 HIGH_PRIORITY
01033/ CS
TDLOF Fallback Default Value: LOW_PRIORITY(Low Priority)
D-00103 to
3 UTRAN
LOFD-0 Flash
01052/ CS
TDLOF Fallback
D-00105 to
2 UTRAN
LBFD-0 Mobility
02018/ Manage
TDLBF ment
D-00201
8
Cell QoffsetF ADD LBFD-0 Coverag Meaning: Indicates the specific frequency offset of the
req CELL 0201801 e Based serving cell. This parameter is contained in the
MOD / Intra- measurement control information and is related to the
CELL TDLBF frequenc handover difficulty between the serving cell and the
D-00201 y neighboring cell. For details, see 3GPP TS 36.331.
LST 801 Handov This parameter applies only to LTE FDD and LTE
CELL er TDD.
LBFD-0
0201803 Cell GUI Value Range: dB-24(-24dB), dB-22(-22dB),
TDLBF Selectio dB-20(-20dB), dB-18(-18dB), dB-16(-16dB),
D-00201 n and dB-14(-14dB), dB-12(-12dB), dB-10(-10dB),
8/ Re- dB-8(-8dB), dB-6(-6dB), dB-5(-5dB), dB-4(-4dB),
LBFD-0 selection dB-3(-3dB), dB-2(-2dB), dB-1(-1dB), dB0(0dB),
02018 Mobility dB1(1dB), dB2(2dB), dB3(3dB), dB4(4dB),
Manage dB5(5dB), dB6(6dB), dB8(8dB), dB10(10dB),
TDLBF dB12(12dB), dB14(14dB), dB16(16dB), dB18(18dB),
ment
D-00201 dB20(20dB), dB22(22dB), dB24(24dB)
802/ Coverag
LBFD-0 e Based Unit: dB
0201802 Inter- Actual Value Range: dB-24, dB-22, dB-20, dB-18,
frequenc dB-16, dB-14, dB-12, dB-10, dB-8, dB-6, dB-5, dB-4,
TDLBF
y dB-3, dB-2, dB-1, dB0, dB1, dB2, dB3, dB4, dB5,
D-00201
Handov dB6, dB8, dB10, dB12, dB14, dB16, dB18, dB20,
804/
er dB22, dB24
LBFD-0
0201804 Distance Default Value: dB0(0dB)
Based
TDLBF
Inter-
D-00201
frequenc
805/
y
LBFD-0
Handov
0201805
er
TDLOF
Service
D-00101
Based
9/
Inter-
LOFD-0
frequenc
01019
y
TDLOF Handov
D-00104 er
3/ PS Inter-
LOFD-0 RAT
01043 Mobility
TDLOF between
D-00107 E-
2/ UTRAN
LOFD-0 and
01072 UTRAN
TDLOF Service
D-00102 based
0/ inter-
LOFD-0 RAT
01020 handove
TDLOF r to
D-00104 UTRAN
6/ Distance
LOFD-0 based
01046 inter-
TDLOF RAT
D-00107 handove
3/ r to
LOFD-0 UTRAN
01073 PS Inter-
RAT
Mobility
between
E-
UTRAN
and
GERAN
Service
based
inter-
RAT
handove
r to
GERAN
Distance
based
inter-
RAT
handove
r to
GERAN
Cell CellSpe ADD LBFD-0 Coverag Meaning: Indicates the cell specific offset for the
cificOffs CELL 0201801 e Based serving cell. It affects the probability of triggering
et MOD / Intra- handovers from the serving cell to its neighboring
CELL TDLBF frequenc cells. A smaller value of this parameter leads to a
D-00201 y higher probability. For details, see 3GPP TS 36.331.
LST 801 Handov This parameter applies only to LTE FDD and LTE
CELL er TDD.
TDLBF
D-00201 Mobility GUI Value Range: dB-24(-24dB), dB-22(-22dB),
8/ Manage dB-20(-20dB), dB-18(-18dB), dB-16(-16dB),
LBFD-0 ment dB-14(-14dB), dB-12(-12dB), dB-10(-10dB),
02018 Coverag dB-8(-8dB), dB-6(-6dB), dB-5(-5dB), dB-4(-4dB),
TDLBF e Based dB-3(-3dB), dB-2(-2dB), dB-1(-1dB), dB0(0dB),
D-00201 Inter- dB1(1dB), dB2(2dB), dB3(3dB), dB4(4dB),
802/ frequenc dB5(5dB), dB6(6dB), dB8(8dB), dB10(10dB),
LBFD-0 y dB12(12dB), dB14(14dB), dB16(16dB), dB18(18dB),
0201802 Handov dB20(20dB), dB22(22dB), dB24(24dB)
er Unit: dB
TDLBF
D-00201 Distance Actual Value Range: dB-24, dB-22, dB-20, dB-18,
804/ Based dB-16, dB-14, dB-12, dB-10, dB-8, dB-6, dB-5, dB-4,
LBFD-0 Inter- dB-3, dB-2, dB-1, dB0, dB1, dB2, dB3, dB4, dB5,
0201804 frequenc dB6, dB8, dB10, dB12, dB14, dB16, dB18, dB20,
y dB22, dB24
TDLBF
Handov Default Value: dB0(0dB)
D-00201
er
805/
LBFD-0 Service
0201805 Based
Inter-
TDLOF
frequenc
D-00101
y
9/
Handov
LOFD-0
er
01019
PS Inter-
TDLOF RAT
D-00104 Mobility
3/ between
LOFD-0 E-
01043 UTRAN
TDLOF and
D-00107 UTRAN
2/ Service
LOFD-0 based
01072 inter-
TDLOF RAT
D-00102 handove
0/ r to
LOFD-0 UTRAN
01020
TDLOF Distance
D-00104 based
6/ inter-
LOFD-0 RAT
01046 handove
TDLOF r to
D-00107 UTRAN
3/ PS Inter-
LOFD-0 RAT
01073 Mobility
between
E-
UTRAN
and
GERAN
Service
based
inter-
RAT
handove
r to
GERAN
Distance
based
inter-
RAT
handove
r to
GERAN
EutranIn CellIndi ADD LBFD-0 Coverag Meaning: Indicates the cell individual offset for the
traFreq vidualOf EUTRA 0201801 e Based intra-frequency neighboring cell. It affects the
NCell fset NINTR / Intra- probability of triggering intra-frequency measurement
AFREQ TDLBF frequenc reports. A larger value of this parameter indicates a
NCELL D-00201 y higher probability. For details, see 3GPP TS 36.331.
MOD 801 Handov This parameter applies only to LTE FDD and LTE
EUTRA LBFD-0 er TDD.
NINTR 0201802 Coverag GUI Value Range: dB-24(-24dB), dB-22(-22dB),
AFREQ / e Based dB-20(-20dB), dB-18(-18dB), dB-16(-16dB),
NCELL TDLBF Inter- dB-14(-14dB), dB-12(-12dB), dB-10(-10dB),
LST D-00201 frequenc dB-8(-8dB), dB-6(-6dB), dB-5(-5dB), dB-4(-4dB),
EUTRA 802 y dB-3(-3dB), dB-2(-2dB), dB-1(-1dB), dB0(0dB),
NINTR LBFD-0 Handov dB1(1dB), dB2(2dB), dB3(3dB), dB4(4dB),
AFREQ 0201804 er dB5(5dB), dB6(6dB), dB8(8dB), dB10(10dB),
NCELL / Distance dB12(12dB), dB14(14dB), dB16(16dB), dB18(18dB),
TDLBF Based dB20(20dB), dB22(22dB), dB24(24dB)
D-00201 Inter- Unit: dB
804 frequenc Actual Value Range: dB-24, dB-22, dB-20, dB-18,
LBFD-0 y dB-16, dB-14, dB-12, dB-10, dB-8, dB-6, dB-5, dB-4,
0201805 Handov dB-3, dB-2, dB-1, dB0, dB1, dB2, dB3, dB4, dB5,
/ er dB6, dB8, dB10, dB12, dB14, dB16, dB18, dB20,
TDLBF Service dB22, dB24
D-00201 Based Default Value: dB0(0dB)
805 Inter-
frequenc
y
Handov
er
IntraFre IntraFre ADD LBFD-0 Coverag Meaning: Indicates the offset for event A3. If the
qHoGro qHoA3 INTRA 0201801 e Based parameter is set to a large value, an intra-frequency
up Offset FREQH / Intra- handover is performed only when the signal quality of
OGROU TDLBF frequenc the neighboring cell is significantly better than that of
P D-00201 y the serving cell and other triggering conditions are
MOD 801 Handov met. For details, see 3GPP TS 36.331. This parameter
INTRA LEOFD- er applies only to LTE FDD and LTE TDD.
FREQH 121204 3D GUI Value Range: -30~30
OGROU Beamfor Unit: 0.5dB
P ming
Actual Value Range: -15~15
LST
INTRA Default Value: 2
FREQH
OGROU
P
InterFre InterFre ADD LBFD-0 Coverag Meaning: Indicates the offset for event A3 associated
qHoGro qHoA3 INTERF 0201802 e Based with inter-frequency handover. This parameter
up Offset REQHO / Inter- determines the border between the serving cell and the
GROUP TDLBF frequenc neighboring cell. If the parameter is set to a large
MOD D-00201 y value, an inter-frequency handover is performed only
INTERF 802 Handov when the signal quality of the neighboring cell is
REQHO LBFD-0 er significantly better than that of the serving cell and
GROUP 0201801 Coverag other triggering conditions are met. For details, see
e Based 3GPP TS 36.331. This parameter applies only to LTE
LST FDD and LTE TDD.
INTERF Intra-
REQHO frequenc GUI Value Range: -30~30
GROUP y Unit: 0.5dB
Handov
er Actual Value Range: -15~15
Default Value: 2
InterFre InterFre ADD LBFD-0 Coverag Meaning: Indicates the hysteresis of events A1/A2 for
qHoGro qHoA1 INTERF 0201802 e Based triggering inter-frequency measurement. This
up A2Hyst REQHO / Inter- parameter is used to prevent frequent triggering of
GROUP TDLBF frequenc event evaluation caused by radio signal fluctuation. In
MOD D-00201 y this way, the probability of ping-pong handovers or
INTERF 802 Handov handover decision errors is reduced. A larger value of
REQHO er this parameter results in a lower probability. This
GROUP parameter applies only to LTE FDD and LTE TDD.
LST GUI Value Range: 0~30
INTERF Unit: 0.5dB
REQHO Actual Value Range: 0~15
GROUP
Default Value: 2
IntraFre IntraFre ADD LBFD-0 Coverag Meaning: Indicates the hysteresis for intra-frequency
qHoGro qHoA3 INTRA 0201801 e Based and inter-frequency handover event A3. This
up Hyst FREQH / Intra- parameter decreases frequent event triggering due to
OGROU TDLBF frequenc radio signal fluctuations and reduces the probability of
P D-00201 y handover decision errors and ping-pong handovers. A
MOD 801 Handov larger value of this parameter results in a lower
INTRA LBFD-0 er probability. For details, see 3GPP TS 36.331. This
FREQH 0201802 Coverag parameter applies only to LTE FDD and LTE TDD.
OGROU / e Based GUI Value Range: 0~30
P TDLBF Inter- Unit: 0.5dB
LST D-00201 frequenc
802 y Actual Value Range: 0~15
INTRA
FREQH Handov Default Value: 2
OGROU er
P
InterFre InterFre ADD LBFD-0 Coverag Meaning: Indicates the hysteresis for event A4. This
qHoGro qHoA4 INTERF 0201802 e Based parameter is used to prevent frequent triggering of
up Hyst REQHO / Inter- event evaluation caused by radio signal fluctuation. In
GROUP TDLBF frequenc this way, the probability of ping-pong handovers or
MOD D-00201 y handover decision errors is reduced. A larger value of
INTERF 802 Handov this parameter results in a lower probability. This
REQHO LBFD-0 er parameter applies only to LTE FDD and LTE TDD.
GROUP 0201804 Distance GUI Value Range: 0~30
LST / Based Unit: 0.5dB
INTERF TDLBF Inter-
D-00201 frequenc Actual Value Range: 0~15
REQHO
GROUP 804 y Default Value: 2
LBFD-0 Handov
0201805 er
/ Service
TDLBF Based
D-00201 Inter-
805 frequenc
y
Handov
er
InterRat InterRat ADD LOFD-0 PS Inter- Meaning: Indicates the hysteresis of events A1/A2 for
HoCom HoA1A INTER 01019/ RAT triggering inter-RAT measurement. This parameter is
mGroup 2Hyst RATHO TDLOF Mobility used to prevent frequent triggering of event evaluation
COMM D-00101 between caused by radio signal fluctuation. In this way, the
GROUP 9 E- probability of ping-pong handovers or handover
MOD LOFD-0 UTRAN decision errors is reduced. A larger value of this
INTER 01020/ and parameter results in a lower probability. This
RATHO TDLOF UTRAN parameter applies only to LTE FDD and LTE TDD.
COMM D-00102 PS Inter- GUI Value Range: 0~30
GROUP 0 RAT Unit: 0.5dB
LST LOFD-0 Mobility
between Actual Value Range: 0~15
INTER 01021/
RATHO TDLOF E- Default Value: 2
COMM D-00102 UTRAN
GROUP 1 and
GERAN
LOFD-0
01022/ PS Inter-
TDLOF RAT
D-00102 Mobility
2 between
E-
TDLOF UTRAN
D-00102 and
3 CDMA2
LBFD-0 000
02018/ SRVCC
TDLBF to
D-00201 UTRAN
8
SRVCC
LBFD-0 to
0201802 GERAN
/
Mobility
TDLBF
Manage
D-00201
ment
802
Coverag
LOFD-0
e Based
01111
Inter-
frequenc
y
Handov
er
PS
Mobility
from E-
UTRAN
to
CDMA2
000
HRPD
Based
on
Frequen
cy-
specific
Factors
specific
Factors
InterRat InterRat ADD LOFD-0 PS Inter- Meaning: Indicates the hysteresis for event B1 related
HoUtran HoUtran INTER 01019/ RAT to inter-RAT handover to UTRAN. This parameter is
Group B1Hyst RATHO TDLOF Mobility used to prevent frequent triggering of event evaluation
UTRAN D-00101 between caused by radio signal fluctuation. In this way, the
GROUP 9 E- probability of ping-pong handovers or handover
MOD LOFD-0 UTRAN decision errors is reduced. A larger value of this
INTER 01022/ and parameter results in a lower probability of ping-pong
RATHO TDLOF UTRAN handovers or handover decision errors. This parameter
UTRAN D-00102 SRVCC applies only to LTE FDD and LTE TDD.
GROUP 2 to GUI Value Range: 0~30
LST LBFD-0 UTRAN Unit: 0.5dB
INTER 02018/ Mobility Actual Value Range: 0~15
RATHO TDLBF Manage
UTRAN D-00201 ment Default Value: 0
GROUP 8
InterRat InterRat ADD LOFD-0 PS Inter- Meaning: Indicates the time-to-trigger for events B1
HoUtran HoUtran INTER 01019/ RAT and B2 related to EUTRAN-to-UTRAN handovers.
Group B1Time RATHO TDLOF Mobility When detecting that the entering condition for the
ToTrig UTRAN D-00101 between corresponding event is fulfilled, the UE does not
GROUP 9 E- immediately send a measurement report to the
MOD LOFD-0 UTRAN eNodeB. Instead, the UE sends a report only when the
INTER 01022/ and entering condition is fulfilled throughout the time-to-
RATHO TDLOF UTRAN trigger. This parameter helps decrease the number of
UTRAN D-00102 SRVCC occasionally triggered event reports, the average
GROUP 2 to number of handovers, and the number of incorrect
UTRAN handovers, preventing unnecessary handovers. This
LST LBFD-0 parameter applies only to LTE FDD and LTE TDD.
INTER 02018/ Mobility
RATHO TDLBF Manage GUI Value Range: 0ms(0ms), 40ms(40ms),
UTRAN D-00201 ment 64ms(64ms), 80ms(80ms), 100ms(100ms),
GROUP 8 128ms(128ms), 160ms(160ms), 256ms(256ms),
Service 320ms(320ms), 480ms(480ms), 512ms(512ms),
LOFD-0 based 640ms(640ms), 1024ms(1024ms), 1280ms(1280ms),
01043/ Inter- 2560ms(2560ms), 5120ms(5120ms)
TDLOF RAT
D-00104 handove Unit: ms
3 r to Actual Value Range: 0ms, 40ms, 64ms, 80ms, 100ms,
LOFD-0 UTRAN 128ms, 160ms, 256ms, 320ms, 480ms, 512ms, 640ms,
01072/ Distance 1024ms, 1280ms, 2560ms, 5120ms
TDLOF based Default Value: 320ms(320ms)
D-00107 Inter-
2 RAT
handove
r to
UTRAN
InterRat InterRat ADD LOFD-0 PS Inter- Meaning: Indicates the hysteresis for event B1 related
HoGera HoGera INTER 01020/ RAT to inter-RAT handover to GERAN. This parameter is
nGroup nB1Hyst RATHO TDLOF Mobility used to prevent frequent triggering of event evaluation
GERAN D-00102 between caused by radio signal fluctuation. In this way, the
GROUP 0 E- probability of ping-pong handovers or handover
MOD LOFD-0 UTRAN decision errors is reduced. A larger value of this
INTER 01023/ and parameter results in a lower probability of ping-pong
RATHO TDLOF GERAN handovers or handover decision errors. This parameter
GERAN D-00102 SRVCC applies only to LTE FDD and LTE TDD.
GROUP 3 to GUI Value Range: 0~30
LST LBFD-0 GERAN Unit: 0.5dB
INTER 02018/ Mobility Actual Value Range: 0~15
RATHO TDLBF Manage
GERAN D-00201 ment Default Value: 2
GROUP 8
InterRat InterRat ADD LOFD-0 PS Inter- Meaning: Indicates the time-to-trigger for events B1
HoGera HoGera INTER 01020/ RAT and B2 related to EUTRAN-to-GERAN handovers.
nGroup nB1Tim RATHO TDLOF Mobility When detecting that the entering condition for the
eToTrig GERAN D-00102 between corresponding event is fulfilled, the UE does not
GROUP 0 E- immediately send a measurement report to the
MOD LOFD-0 UTRAN eNodeB. Instead, the UE sends a report only when the
INTER 01023/ and entering condition is fulfilled throughout the time-to-
RATHO TDLOF GERAN trigger. This parameter helps decrease the number of
GERAN D-00102 SRVCC occasionally triggered event reports, the average
GROUP 3 to number of handovers, and the number of incorrect
GERAN handovers, preventing unnecessary handovers. This
LST LBFD-0 parameter applies only to LTE FDD and LTE TDD.
INTER 02018/ Mobility
RATHO TDLBF Manage GUI Value Range: 0ms(0ms), 40ms(40ms),
GERAN D-00201 ment 64ms(64ms), 80ms(80ms), 100ms(100ms),
GROUP 8 128ms(128ms), 160ms(160ms), 256ms(256ms),
Service 320ms(320ms), 480ms(480ms), 512ms(512ms),
LOFD-0 based 640ms(640ms), 1024ms(1024ms), 1280ms(1280ms),
01046/ Inter- 2560ms(2560ms), 5120ms(5120ms)
TDLOF RAT
D-00104 handove Unit: ms
6 r to Actual Value Range: 0ms, 40ms, 64ms, 80ms, 100ms,
LOFD-0 GERAN 128ms, 160ms, 256ms, 320ms, 480ms, 512ms, 640ms,
01073/ Distance 1024ms, 1280ms, 2560ms, 5120ms
TDLOF based Default Value: 640ms(640ms)
D-00107 Inter-
3 RAT
handove
r to
GERAN
CellQci QciPrior ADD LBFD-0 Coverag Meaning: Indicates the QCI priority used by each
Para ityForH CELLQ 0201801 e Based QCI-based handover algorithm. A larger value of this
o CIPAR / Intra- parameter indicates a lower priority. This parameter
A TDLBF frequenc applies to handover parameter selection based on QCI
MOD D-00201 y priorities, target frequency selection in service-based
CELLQ 801 Handov inter-frequency handovers, and inter-RAT handover
CIPAR LBFD-0 er policy selection. For a service that involves all the
A 0201802 Coverag preceding selection, the setting of this parameter
/ e Based determines the handover parameter, target frequency,
LST and handover policy corresponding to a QCI. This
CELLQ TDLBF Inter-
D-00201 frequenc parameter applies only to LTE FDD and LTE TDD.
CIPAR
A 802 y GUI Value Range: 1~254
LBFD-0 Handov Unit: None
0201804 er
Actual Value Range: 1~254
/ Distance
TDLBF Based Default Value: 9
D-00201 Inter-
804 frequenc
LBFD-0 y
0201805 Handov
/ er
TDLBF Service
D-00201 Based
805 Inter-
LOFD-0 frequenc
01072/ y
TDLOF Handov
D-00107 er
2 Distance
LOFD-0 based
01073/ Inter-
TDLOF RAT
D-00107 handove
3 r to
UTRAN
LOFD-0
01019/ Distance
TDLOF based
D-00101 Inter-
9 RAT
handove
LOFD-0 r to
01020/ GERAN
TDLOF
D-00102 PS Inter-
0 RAT
Mobility
between
E-
UTRAN
and
UTRAN
PS Inter-
RAT
Mobility
between
E-
UTRAN
and
GERAN
IntraRat IntraRat MOD LBFD-0 Coverag Meaning: Indicates the maximum number of cells to
HoCom HoMax INTRA 0201801 e Based be included in the measurement report after an intra-
m RprtCell RATHO / Intra- RAT inter-frequency or intra-RAT intra-frequency
COMM TDLBF frequenc measurement event for handover purposes or a
LST D-00201 y periodic intra-RAT measurement for ANR purposes is
INTRA 801 Handov triggered. For details, see 3GPP TS 36.331. This
RATHO LBFD-0 er parameter applies only to LTE FDD and LTE TDD.
COMM 0201802 Coverag GUI Value Range: 1~8
/ e Based Unit: None
TDLBF Inter-
frequenc Actual Value Range: 1~8
D-00201
802 y Default Value: 4
Handov
LBFD-0
er
0201804
/ Distance
TDLBF Based
D-00201 Inter-
804 frequenc
y
LBFD-0
Handov
0201805
er
/
TDLBF Service
D-00201 Based
805 Inter-
frequenc
TDLBF y
D-00201 Handov
8 er
TDLOF Mobility
D-00102 Manage
2 ment
TDLOF SRVCC
D-00102 to
3 UTRAN
TDLOF SRVCC
D-00103 to
3 GERAN
TDLOF CS
D-00103 Fallback
4 to
TDLOF UTRAN
D-00103 CS
5 Fallback
TDLOF to
D-00101 GERAN
9
CS
Fallback
to
CDMA2
000
1xRTT
PS Inter-
RAT
Mobility
between
E-
UTRAN
and
UTRAN
Mobility
between
E-
UTRAN
and
UTRAN
InterRat InterRat MOD LOFD-0 Enhance Meaning: Indicates the maximum number of cells to
HoCom HoMax INTER 01090/ d CS be included in the measurement report after an inter-
m RprtCell RATHO TDLOF Fallback RAT handover event or a periodic inter-RAT
COMM D-00109 to measurement for ANR purposes is triggered. For
LST 0 CDMA2 details, see 3GPP TS 36.331. This parameter applies
INTER LOFD-0 000 only to LTE FDD and LTE TDD.
RATHO 01019/ 1xRTT GUI Value Range: 1~8
COMM TDLOF PS Inter- Unit: None
D-00101 RAT
9 Mobility Actual Value Range: 1~8
LOFD-0 PS Inter-
01021/ RAT
TDLOF Mobility
D-00102 between
1 E-
UTRAN
LOFD-0 and
01022/ GERAN
TDLOF
PS Inter-
D-00102
RAT
2
Mobility
LOFD-0 between
01023/ E-
TDLOF UTRAN
D-00102 and
3 CDMA2
LOFD-0 000
01043/ SRVCC
TDLOF to
D-00104 UTRAN
3
SRVCC
LOFD-0 to
01072/ GERAN
TDLOF
Service
D-00107
based
2
Inter-
LOFD-0 RAT
01046/ handove
TDLOF r to
D-00104 UTRAN
6 Distance
based
LOFD-0 Inter-
01073/ RAT
TDLOF handove
D-00107 r to
3 UTRAN
LBFD-0 Service
02018/ based
TDLBF Inter-
D-00201 RAT
8 handove
r to
GERAN
Distance
based
Inter-
RAT
handove
r to
GERAN
Mobility
Manage
ment
InterRat InterRat MOD LOFD-0 Enhance Meaning: Indicates the number of periodical
HoCom HoRprt INTER 01090/ d CS measurement reports to be sent after an inter-RAT
m Amount RATHO TDLOF Fallback handover event is triggered. It is used to prevent the
COMM D-00109 to impact of measurement report loss and internal
LST 0 CDMA2 processing failure on the handover. For details, see
INTER LOFD-0 000 3GPP TS 36.331. This parameter applies only to LTE
RATHO 01019/ 1xRTT FDD and LTE TDD.
COMM TDLOF PS Inter- GUI Value Range: r1(1), r2(2), r4(4), r8(8), r16(16),
D-00101 RAT r32(32), r64(64), Infinity(Infinity)
9 Mobility Unit: None
LOFD-0 between
E- Actual Value Range: r1, r2, r4, r8, r16, r32, r64,
01020/ Infinity
TDLOF UTRAN
D-00102 and Default Value: Infinity(Infinity)
0 UTRAN
LOFD-0 PS Inter-
01021/ RAT
TDLOF Mobility
D-00102 between
1 E-
UTRAN
LOFD-0 and
01022/ GERAN
TDLOF
PS Inter-
D-00102
RAT
2
Mobility
LOFD-0 between
01023/ E-
TDLOF UTRAN
D-00102 and
3 CDMA2
LOFD-0 000
01043/ SRVCC
TDLOF to
D-00104 UTRAN
3
SRVCC
LOFD-0 to
01072/ GERAN
TDLOF
Service
D-00107
based
2
Inter-
LOFD-0 RAT
01046/ handove
TDLOF r to
D-00104 UTRAN
6 Distance
based
LOFD-0 Inter-
01073/ RAT
TDLOF handove
D-00107 r to
3 UTRAN
LBFD-0 Service
02018/ based
TDLBF Inter-
D-00201 RAT
8 handove
r to
GERAN
Distance
based
Inter-
RAT
handove
r to
GERAN
Mobility
Manage
ment
InterRat InterRat MOD LOFD-0 PS Inter- Meaning: Indicates the quantity to be measured for
HoCom HoUtran INTER 01019/ RAT handovers to UTRAN FDD. The RSCP values are
m B1Meas RATHO TDLOF Mobility relatively stable while the Ec/N0 values fluctuate with
Quan COMM D-00101 between the network load. The value BOTH applies only to
LST 9 E- UEs complying with 3GPP Release 10. UEs
INTER LOFD-0 UTRAN complying with 3GPP Release 10 contain RSCP and
RATHO 01022/ and Ec/N0 in measurement reports. When both RSCP- and
COMM TDLOF UTRAN Ec/N0-based trigger conditions are met, handovers
D-00102 SRVCC can be triggered. For UEs complying with 3GPP
2 to Release 8 or 9, the value BOTH is equivalent to the
UTRAN value RSCP. QoE-based handover algorithms do not
LOFD-0 apply to UEs complying with 3GPP Release 8 and
01033/ CS Release 9, and the parameter value is fixed at ECN0.
TDLOF Fallback For details, see 3GPP TS 36.331. This parameter
D-00103 to applies only to LTE FDD and LTE TDD.
3 UTRAN
GUI Value Range: RSCP, ECN0, BOTH
LBFD-0 Mobility
02018/ Manage Unit: None
TDLBF ment Actual Value Range: RSCP, ECN0, BOTH
D-00201 Service Default Value: ECN0
8 based
LOFD-0 Inter-
01043/ RAT
TDLOF handove
D-00104 r to
3 UTRAN
InterRat InterRat MOD LOFD-0 PS Inter- Meaning: Indicates the triggering quantity of inter-
HoCom HoA1A INTER 01019/ RAT RAT events A1 and A2. RSRP measurements slightly
m 2TrigQu RATHO TDLOF Mobility vary with the load, and there is little signal fluctuation.
an COMM D-00101 between By contrast, RSRQ measurements vary with the load
LST 9 E- and are likely to reflect the signal quality of the cell in
INTER LOFD-0 UTRAN real time. If this parameter is set to BOTH, both
RATHO 01020/ and RSRP- and RSRQ-based measurement configurations
COMM TDLOF UTRAN are delivered. When either the RSRP-based or RSRQ-
D-00102 PS Inter- based entering condition of event A1 or A2 is met, the
0 RAT UE reports event A1 or A2. For details, see 3GPP TS
Mobility 36.331.This parameter applies only to LTE FDD and
LOFD-0 LTE TDD.
01021/ between
TDLOF E- GUI Value Range: RSRP, RSRQ, BOTH
D-00102 UTRAN Unit: None
1 and
GERAN Actual Value Range: RSRP, RSRQ, BOTH
LOFD-0 Default Value: RSRP
01022/ PS Inter-
TDLOF RAT
D-00102 Mobility
2 between
E-
LOFD-0 UTRAN
01023/ and
TDLOF CDMA2
D-00102 000
3
SRVCC
LBFD-0 to
02018/ UTRAN
TDLBF
D-00201 SRVCC
8 to
GERAN
LOFD-0
01111/ Mobility
TDLOF Manage
D-00111 ment
1 PS
Mobility
from E-
UTRAN
to
CDMA2
000
HRPD
Based
on
Frequen
cy-
specific
Factors
HoSwitch:Off, CdmaHrpdOptimisedHoSwitch:Off,
GeranNaccSwitch:Off, GeranCcoSwitch:Off,
Cdma1xRttSrvccSwitch:Off, CdmaHrpdRedirectS-
witch:Off, Cdma1xRttRedirectSwitch:Off,
BlindHoSwitch:Off, LcsSrvccSwitch:Off,
AutoGapSwitch:Off, UeVoipOnHspaCapSwitch:Off,
UtranFddB1CapSwitch:Off, CdmaHrpdNonOptMea-
HoSwitch:Off
D-00102 Handov
3 er
LOFD-0 SRVCC
01033/ to
TDLOF UTRAN
D-00103 SRVCC
3 to
LOFD-0 GERAN
01034/ CS
TDLOF Fallback
D-00103 to
4 UTRAN
LOFD-0 CS
01035/ Fallback
TDLOF to
D-00103 GERAN
5
CS
LOFD-0 Fallback
01043/ to
TDLOF CDMA2
D-00104 000
3 1xRTT
LOFD-0 Service
01072/ based
TDLOF Inter-
D-00107 RAT
2 handove
LOFD-0 r to
01046/ UTRAN
TDLOF Distance
D-00104 based
6 Inter-
LOFD-0 RAT
01073/ handove
TDLOF r to
D-00107 UTRAN
3 Service
based
Inter-
RAT
handove
r to
GERAN
Distance
based
Inter-
RAT
handove
r to
GERAN
LBFD-0 y
0201805 Handov
/ er
TDLBF Service
D-00201 Based
805 Inter-
frequenc
y
Handov
er
LBFD-0 y
0201805 Handov
/ er
TDLBF Service
D-00201 Based
805 Inter-
frequenc
y
Handov
er
LOFD-0 GERAN GUI Value Range: FC0, FC1, FC2, FC3, FC4, FC5,
01034/ CS FC6, FC7, FC8, FC9, FC11, FC13, FC15, FC17,
TDLOF Fallback FC19
D-00103 to Unit: None
4 GERAN Actual Value Range: FC0, FC1, FC2, FC3, FC4, FC5,
LOFD-0 Flash FC6, FC7, FC8, FC9, FC11, FC13, FC15, FC17,
01053/ CS FC19
TDLOF Fallback Default Value: FC6
D-00105 to
3 GERAN
LBFD-0 Mobility
02018/ Manage
TDLBF ment
D-00201
8
HoMeas SMeasur MOD LBFD-0 Coverag Meaning: Indicates the threshold below which
Comm e HOME 0201801 e Based measurements on neighboring cells are started. If the
ASCOM / Intra- signal quality of the serving cell exceeds this
M TDLBF frequenc threshold, the UE is not required to perform intra-
LST D-00201 y frequency, inter-frequency, or inter-RAT
HOME 801 Handov measurements, leading to reduced power
ASCOM LBFD-0 er consumption. This parameter applies only to LTE
M 0201802 Coverag FDD and LTE TDD.
/ e Based GUI Value Range: -140~-43
TDLBF Inter- Unit: dBm
D-00201 frequenc
802 y Actual Value Range: -140~-43
Handov Default Value: -44
LBFD-0
0201804 er
/ Distance
TDLBF Based
D-00201 Inter-
804 frequenc
y
LBFD-0
Handov
0201805
er
/
TDLBF Service
D-00201 Based
805 Inter-
frequenc
LOFD-0
y
01019/
Handov
TDLOF
er
D-00101
9 PS Inter-
RAT
LOFD-0
Mobility
01020/
between
TDLOF
E-
D-00102
UTRAN
0
and
LOFD-0 UTRAN
01021/ PS Inter-
TDLOF RAT
D-00102 Mobility
1 between
LBFD-0 E-
02018/ UTRAN
TDLBF and
D-00201 GERAN
8 PS Inter-
LOFD-0 RAT
01022/ Mobility
TDLOF between
D-00102 E-
2 UTRAN
LOFD-0 and
01023/ CDMA2
TDLOF 000
D-00102 Mobility
3 Manage
LOFD-0 ment
01043/ SRVCC
TDLOF to
D-00104 UTRAN
3 SRVCC
LOFD-0 to
01072/ GERAN
TDLOF Service
D-00107 based
2 Inter-
LOFD-0 RAT
01046/ handove
TDLOF r to
D-00104 UTRAN
6 Distance
LOFD-0 based
01073/ Inter-
TDLOF RAT
D-00107 handove
3 r to
UTRAN
Service
based
Inter-
RAT
handove
r to
GERAN
Distance
based
Inter-
RAT
handove
r to
GERAN
D-00100 DL 4x4 services and other services when both of the following
1 MIMO conditions are met: (1) The EPC delivers information
LOFD-0 DL 2x2 about bearers with QCI 1 and other QCIs; (2) The UE
01003 MIMO exits the idle mode. After the QCI-1 service bearers
are set up, the UE is handed over to an inter-frequency
TDLAO DL 4x2 cell. This option applies only to LTE FDD and LTE
FD-001 MIMO TDD.
00114 DL 2-
TDLAO Layer ApCqiAndAckAbnCtrlSwitch: Indicates whether to
FD-081 MIMO enable a workaround of problems that may occur
409 Based when aperiodic CQI reports in 3-1 reporting mode and
on TM9 ACKs/NACKs are transmitted simultaneously in a
LAOFD cell. If this option is selected, the eNodeB performs
-001001 DL 4- preallocation for aperiodic CQI reports. If this option
/ Layer is deselected, the eNodeB performs CQI_ONLY
TDLAO MIMO scheduling on aperiodic CQI reports. This option
FD-001 Based applies only to LTE FDD and LTE TDD.
001 on TM9
TDLAO LTE-A UeSRSAntSelectCtrlSwitch: Indicates whether to
FD-110 Introduc disable antenna selection for SRS transmission. If this
401 tion option is selected, antenna selection is disabled. This
option applies only to LTE TDD.
TDLAO Inter-
FD-081 eNodeB CaCqiAndAckAbnCtrlSwitch: Indicates whether to
402 CA enable a workaround of problems that may occur
LBFD-0 based on when periodic CQI reports and ACKs/NACKs are
60101 Coordin transmitted simultaneously in a cell in CA scenarios.
ated If this option is selected, the eNodeB sets the
MRFD- eNodeB SimulAckNackAndCqiSwitch parameter to OFF(Off)
101222 for CA UEs. If this option is deselected, the eNodeB
Inter-
MRFD- sets the SimulAckNackAndCqiSwitch parameter
eNodeB
111222 based on the original algorithm for CA UEs.
CA
Based HoRlcSnSizeSwitch: Controls the configuration of
on RLC sn-FieldLength during handovers. If this option
Relaxed is selected, the configuration of RLC sn-FieldLength
Backhau for the target cell is the same as that for the source
l cell. If this option is deselected, RLC sn-FieldLength
for the target cell is set to the value configured at the
Optimiz target side.
ation of
CQI FddTddCaPcellDuplexFdd: Indicates whether the
Reportin eNodeB regards that a UE supports FDD+TDD CA
g with an LTE FDD cell serving as its PCell when the
FDD UE reports the FDD+TDD CA band combination but
+TDD does not report IE tdd-FDD-CA-PCellDuplex-r12. If
Downlin this option is selected, the eNodeB regards that the UE
k supports this type of CA. If this option is deselected,
Carrier the eNodeB regards that the UE does not support this
Aggrega type of CA. This option applies only to LTE FDD and
tion LTE TDD.
InterRat InterRat ADD LOFD-0 SRVCC Meaning: Indicates the group ID of the parameters
PolicyCf PolicyCf INTER 01022/ to related to the inter-RAT handover. This parameter
gGroup gGroupI RATPO TDLOF UTRAN applies only to LTE FDD and LTE TDD.
d LICYCF D-00102 SRVCC GUI Value Range: 0~39
GGROU 2 to
P Unit: None
LOFD-0 GERAN
LST 01023/ Actual Value Range: 0~39
PS Inter-
INTER TDLOF RAT Default Value: None
RATPO D-00102 Mobility
LICYCF 3 between
GGROU LOFD-0 E-
P 01019/ UTRAN
MOD TDLOF and
INTER D-00101 UTRAN
RATPO 9 PS Inter-
LICYCF LOFD-0 RAT
GGROU 01020/ Mobility
P TDLOF between
RMV D-00102 E-
INTER 0 UTRAN
RATPO LOFD-0 and
LICYCF 01021/ GERAN
GGROU TDLOF PS Inter-
P D-00102 RAT
1 Mobility
between
E-
UTRAN
and
CDMA2
000
QciPara InterRat ADD LOFD-0 PS Inter- Meaning: Indicates the group ID of the parameters
PolicyCf QCIPA 01019/ RAT related to the inter-RAT handover with the extended
gGroupI RA TDLOF Mobility QCI. This parameter applies only to LTE FDD and
d MOD D-00101 between LTE TDD.
QCIPA 9 E- GUI Value Range: 0~39
RA LOFD-0 UTRAN
and Unit: None
LST 01020/
TDLOF UTRAN Actual Value Range: 0~39
QCIPA
RA D-00102 PS Inter- Default Value: 0
0 RAT
LOFD-0 Mobility
01021/ between
TDLOF E-
D-00102 UTRAN
1 and
GERAN
LOFD-0
01022/ PS Inter-
TDLOF RAT
D-00102 Mobility
2 between
E-
LOFD-0 UTRAN
01023/ and
TDLOF CDMA2
D-00102 000
3
SRVCC
LOFD-0 to
01035/ UTRAN
TDLOF
D-00103 SRVCC
5 to
GERAN
LBFD-0
02018/ CS
TDLBF Fallback
D-00201 to
8 CDMA2
000
1xRTT
Mobility
Manage
ment
LBFD-0 Mobility and blind handovers can be triggered only if these two
02018/ Manage options are selected. This option applies only to LTE
TDLBF ment FDD and LTE TDD.
D-00201 NSA GUI Value Range: BlindHoSwitch(BlindHoSwitch),
8 Network UtranPsHoSwitch(UtranPsHoSwitch),
MRFD- ing UtranSrvccSwitch(UtranSrvccSwitch),
131122 based on GeranSrvccSwitch(GeranSrvccSwitch),
MRFD- EPC(LT UtranRedirectSwitch(UtranRedirectSwitch),
131132 E FDD) GeranRedirectSwitch(GeranRedirectSwitch),
NSA UFCsfbBlindHoDisSwitch(UFCsfbBlindHoDisS-
Network witch), HighSpeedCsfbBlind-
ing Switch(HighSpeedCsfbBlindSwitch)
based on Unit: None
EPC(LT Actual Value Range: BlindHoSwitch,
E TDD) UtranPsHoSwitch, UtranSrvccSwitch,
GeranSrvccSwitch, UtranRedirectSwitch,
GeranRedirectSwitch, UFCsfbBlindHoDisSwitch,
HighSpeedCsfbBlindSwitch
Default Value: BlindHoSwitch:Off,
UtranPsHoSwitch:Off, UtranSrvccSwitch:Off,
GeranSrvccSwitch:Off, UtranRedirectSwitch:Off,
GeranRedirectSwitch:Off, UFCsfbBlindHoDisS-
witch:Off, HighSpeedCsfbBlindSwitch:Off
InterRat CellInfo MOD LOFD-0 PS Inter- Meaning: Indicates the maximum number of UTRAN
HoCom MaxUtr INTER 01019/ RAT cell system information messages that can be
m anCellN RATHO TDLOF Mobility transmitted during a flash redirection procedure. This
um COMM D-00101 between parameter applies only to LTE FDD and LTE TDD.
LST 9 E- GUI Value Range: 1~16
INTER LOFD-0 UTRAN
and Unit: None
RATHO 01052/
COMM TDLOF UTRAN Actual Value Range: 1~16
D-00105 Flash Default Value: 8
2 CS
LBFD-0 Fallback
02018/ to
TDLBF UTRAN
D-00201 Mobility
8 Manage
LOFD-0 ment
01033/ CS
TDLOF Fallback
D-00103 to
3 UTRAN
HoMeas ResHoP MOD LBFD-0 Coverag Meaning: Indicates the penalty timer length for not
Comm reFailPu HOME 0201801 e Based allowing handovers (excluding MLB) to the target cell
nishTim ASCOM / Intra- when a handover preparation fails due to resource-
er M TDLBF frequenc related causes during handovers (including CSFB,
LST D-00201 y coverage-based, uplink-quality-based, and distance-
HOME 801 Handov based handovers) to the target cell. If this parameter is
ASCOM LBFD-0 er set to 0, no penalty is performed. This parameter
M 0201802 Coverag applies only to LTE FDD and LTE TDD.
/ e Based GUI Value Range: 0~50
TDLBF Inter- Unit: s
D-00201 frequenc
802 y Actual Value Range: 0~50
Handov Default Value: 0
LBFD-0
0201804 er
/ Distance
TDLBF Based
D-00201 Inter-
804 frequenc
LOFD-0 y
01022/ Handov
TDLOF er
D-00102 SRVCC
2 to
LOFD-0 UTRAN
01023/ SRVCC
TDLOF to
D-00102 GERAN
3 CS
LOFD-0 Fallback
01033/ to
TDLOF UTRAN
D-00103 CS
3 Fallback
LOFD-0 to
01034/ GERAN
TDLOF PS Inter-
D-00103 RAT
4 Mobility
LOFD-0 between
01019/ E-
TDLOF UTRAN
D-00101 and
9 UTRAN
LOFD-0 PS Inter-
01020/ RAT
TDLOF Mobility
D-00102 between
0 E-
LOFD-0 UTRAN
01021/ and
TDLOF GERAN
D-00102 PS Inter-
1 RAT
LOFD-0 Mobility
01072/ between
TDLOF E-
D-00107 UTRAN
2 and
CDMA2
LOFD-0 000
01073/
TDLOF Distance
D-00107 based
3 Inter-
RAT
handove
r to
UTRAN
Distance
based
Inter-
RAT
handove
r to
GERAN
HoMeas NonRes MOD LBFD-0 Coverag Meaning: Indicates the number of penalty times none
Comm HoPreFa HOME 0201801 e Based of the handovers is allowed to the target cell when a
ilPunish ASCOM / Intra- handover preparation fails due to non-resource-related
Times M TDLBF frequenc causes on the target cell. If this parameter is set to 0,
LST D-00201 y the target cell is not penalized or is penalized
HOME 801 Handov permanently if a handover fails due to non-resource-
ASCOM LBFD-0 er related causes. That is, the number of handover
M 0201802 Coverag attempts to the target cell is unlimited. This parameter
/ e Based applies only to LTE FDD and LTE TDD.
TDLBF Inter- GUI Value Range: 0~200
D-00201 frequenc Unit: time
802 y
Handov Actual Value Range: 0~200
LBFD-0
er Default Value: 10
0201804
/ Distance
TDLBF Based
D-00201 Inter-
804 frequenc
LBFD-0 y
0201805 Handov
/ er
TDLBF Service
D-00201 Based
805 Inter-
LOFD-0 frequenc
01022/ y
TDLOF Handov
D-00102 er
2 SRVCC
LOFD-0 to
01023/ UTRAN
TDLOF SRVCC
D-00102 to
3 GERAN
LOFD-0 CS
01033/ Fallback
TDLOF to
D-00103 UTRAN
3 CS
LOFD-0 Fallback
01034/ to
TDLOF GERAN
D-00103 PS Inter-
4 RAT
LOFD-0 Mobility
01019/ between
TDLOF E-
D-00101 UTRAN
9 and
LOFD-0 UTRAN
01020/ PS Inter-
TDLOF RAT
D-00102 Mobility
0 between
LOFD-0 E-
01021/ UTRAN
TDLOF and
D-00102 GERAN
1 PS Inter-
LOFD-0 RAT
01043/ Mobility
TDLOF between
D-00104 E-
3 UTRAN
and
LOFD-0 CDMA2
01072/ 000
TDLOF
D-00107 Service
2 based
Inter-
LOFD-0 RAT
01046/ handove
TDLOF r to
D-00104 UTRAN
6
Distance
LOFD-0 based
01073/ Inter-
TDLOF RAT
D-00107 handove
3 r to
LOFD-0 UTRAN
0105401 Service
/ based
TDLOF Inter-
D-00105 RAT
401 handove
LBFD-0 r to
02018/ GERAN
TDLBF Distance
D-00201 based
8 Inter-
RAT
handove
r to
GERAN
Camp &
Handov
er Based
on SPID
Mobility
Manage
ment
HoMeas OptHoP MOD LBFD-0 Service Meaning: Indicates the penalty timer length for not
Comm reFailPu HOME 0201805 Based allowing handovers (excluding MLB) to the target cell
nishTim ASCOM / Inter- when a handover preparation fails due to
er M TDLBF frequenc optimization-related causes during handovers
LST D-00201 y (including frequency-priority-based handovers,
HOME 805 Handov service-based handovers, SPID-based handovers back
ASCOM LOFD-0 er to the HPLMN, and QoE-based handovers) to the
M 01043/ Service target cell. This parameter applies only to LTE FDD
TDLOF based and LTE TDD.
D-00104 Inter- GUI Value Range: 0~20
3 RAT Unit: 30s
LOFD-0 handove
r to Actual Value Range: 0~600
01046/
TDLOF UTRAN Default Value: 0
D-00104 Service
6 based
LOFD-0 Inter-
0105401 RAT
/ handove
TDLOF r to
D-00105 GERAN
401 Camp &
LBFD-0 Handov
02018/ er Based
TDLBF on SPID
D-00201 Mobility
8 Manage
ment
HoMeas NonRes MOD LBFD-0 Coverag Meaning: Indicates the number of handover attempts
Comm HoPreFa HOME 0201801 e Based to the target cell when a handover preparation fails
ilRetryT ASCOM / Intra- due to non-resource-related causes on the target cell.
imes M TDLBF frequenc If this parameter is set to 200, the number of handover
LST D-00201 y attempts is unlimited. This parameter applies only to
HOME 801 Handov LTE FDD and LTE TDD.
ASCOM LBFD-0 er GUI Value Range: 0~200
M 0201802 Coverag Unit: time
/ e Based
TDLBF Inter- Actual Value Range: 0~200
D-00201 frequenc Default Value: 1
802 y
LBFD-0 Handov
0201804 er
/ Distance
TDLBF Based
D-00201 Inter-
804 frequenc
LBFD-0 y
0201805 Handov
/ er
TDLBF Service
D-00201 Based
805 Inter-
LOFD-0 frequenc
01022/ y
TDLOF Handov
D-00102 er
2 SRVCC
LOFD-0 to
01023/ UTRAN
TDLOF SRVCC
D-00102 to
3 GERAN
LOFD-0 CS
01033/ Fallback
TDLOF to
D-00103 UTRAN
3 CS
LOFD-0 Fallback
01034/ to
TDLOF GERAN
D-00103 PS Inter-
4 RAT
LOFD-0 Mobility
01019/ between
TDLOF E-
D-00101 UTRAN
9 and
LOFD-0 UTRAN
01020/ PS Inter-
TDLOF RAT
D-00102 Mobility
0 between
LOFD-0 E-
01021/ UTRAN
TDLOF and
D-00102 GERAN
1 PS Inter-
LOFD-0 RAT
01043/ Mobility
TDLOF between
D-00104 E-
3 UTRAN
and
LOFD-0 CDMA2
01072/ 000
TDLOF
D-00107 Service
2 based
Inter-
LOFD-0 RAT
01046/ handove
TDLOF r to
D-00104 UTRAN
6
Distance
LOFD-0 based
01073/ Inter-
TDLOF RAT
D-00107 handove
3 r to
LOFD-0 UTRAN
0105401 Service
/ based
TDLOF Inter-
D-00105 RAT
401 handove
LBFD-0 r to
02018/ GERAN
TDLBF Distance
D-00201 based
8 Inter-
RAT
handove
r to
GERAN
Camp &
Handov
er Based
on SPID
Mobility
Manage
ment
CellHoP InterRat MOD LOFD-0 SRVCC Meaning: Indicates the number of inter-RAT handover
araCfg UuHoFa CELLH 01022/ to retries initiated to the same target cell after the
ilRetryT OPARA TDLOF UTRAN handover fails over the air interface in the target cell.
imes CFG D-00102 SRVCC This parameter applies only to LTE FDD and LTE
LST 2 to TDD.
CELLH LOFD-0 GERAN GUI Value Range: 0~50
OPARA 01023/ PS Inter- Unit: None
CFG TDLOF RAT
D-00102 Actual Value Range: 0~50
Mobility
3 between Default Value: 10
LOFD-0 E-
01019/ UTRAN
TDLOF and
D-00101 UTRAN
9 PS Inter-
LOFD-0 RAT
01020/ Mobility
TDLOF between
D-00102 E-
0 UTRAN
TDLBF and
D-00201 GERAN
8 Mobility
Manage
ment
GlobalP HoProc MOD LBFD-0 Mobility Meaning: Indicates whether to control the handover
rocSwitc CtrlSwit GLOBA 02018/ Manage process. This parameter provides the following
h ch LPROC TDLBF ment options: HoDataSendCtrlSwitch: If this option is
SWITC D-00201 selected, the eNodeB sends data packets to a
H 8 handover-incoming UE after sending a random access
LST response (RAR) in a non-contention-based random
GLOBA access procedure. If this option is deselected, the
LPROC eNodeB sends data packets to the UE after receiving
SWITC an Msg3 message in the non-contention-based random
H access procedure. This option applies only to LTE
FDD and LTE TDD. ErabFlowFirstSwitch: This
option specifies the policy for handling the conflicts
between handover and bearer procedures. If this
option is selected and a handover procedure conflicts
with an E-RAB setup, modification, or deletion
procedure, the eNodeB performs as follows: 1. If the
handover is not for CSFB or the SRVCC procedure
conflicts with a QCI 1 E-RAB release procedure, the
eNodeB processes the bearer procedure first. 2. If the
handover is for CSFB or the SRVCC procedure
conflicts with another E-RAB-related procedure, the
eNodeB processes the handover procedure first. If this
option is deselected in the preceding scenario, the
eNodeB always processes the handover procedure
first. This option applies only to LTE FDD and LTE
TDD. CsfbFlowFirstSwitch: This option specifies the
policy for handling the conflicts between handover
and CSFB procedures. If this option is selected and
the handover and CSFB procedures conflict, the
eNodeB processes the CSFB procedure first. If this
option is deselected in the preceding scenario, the
eNodeB processes the handover procedure first. This
option applies only to LTE FDD and LTE TDD.
GUI Value Range: HoDataSendCtrlS-
witch(HoDataSendCtrlSwitch),
ErabFlowFirstSwitch(ErabFlowFirstSwitch),
CsfbFlowFirstSwitch(CsfbFlowFirstSwitch)
Unit: None
Actual Value Range: HoDataSendCtrlSwitch,
ErabFlowFirstSwitch, CsfbFlowFirstSwitch
Default Value: HoDataSendCtrlSwitch:Off,
ErabFlowFirstSwitch:Off, CsfbFlowFirstSwitch:Off
CellQci IntraFre ADD LBFD-0 Coverag Meaning: Indicates the ID of a parameter group
Para qHoGro CELLQ 0201801 e Based related to intra-frequency handover. This parameter
upId CIPAR / Intra- applies only to LTE FDD and LTE TDD.
A TDLBF frequenc GUI Value Range: 0~9
MOD D-00201 y
801 Handov Unit: None
CELLQ
CIPAR er Actual Value Range: 0~9
A Default Value: 0
LST
CELLQ
CIPAR
A
CellQci InterFre ADD LBFD-0 Coverag Meaning: Indicates the ID of a parameter group
Para qHoGro CELLQ 0201802 e Based related to inter-frequency handovers. This parameter
upId CIPAR / Inter- applies only to LTE FDD and LTE TDD.
A TDLBF frequenc GUI Value Range: 0~9
MOD D-00201 y
802 Handov Unit: None
CELLQ
CIPAR LBFD-0 er Actual Value Range: 0~9
A 0201804 Distance Default Value: 0
LST / Based
CELLQ TDLBF Inter-
CIPAR D-00201 frequenc
A 804 y
LBFD-0 Handov
0201805 er
/ Service
TDLBF Based
D-00201 Inter-
805 frequenc
y
Handov
er
CellQci InterRat ADD LOFD-0 PS Inter- Meaning: Indicates the ID of a common parameter
Para HoCom CELLQ 01019/ RAT group related to inter-RAT handover. This parameter
mGroup CIPAR TDLOF Mobility applies only to LTE FDD and LTE TDD.
Id A D-00101 between GUI Value Range: 0~9
MOD 9 E-
UTRAN Unit: None
CELLQ LOFD-0
CIPAR 01020/ and Actual Value Range: 0~9
A TDLOF UTRAN Default Value: 0
LST D-00102 PS Inter-
CELLQ 0 RAT
CIPAR LOFD-0 Mobility
A 01021/ between
TDLOF E-
D-00102 UTRAN
1 and
GERAN
LOFD-0
01022/ PS Inter-
TDLOF RAT
D-00102 Mobility
2 between
E-
LOFD-0 UTRAN
01023/ and
TDLOF CDMA2
D-00102 000
3
SRVCC
to
UTRAN
SRVCC
to
GERAN
CellQci InterRat ADD LOFD-0 PS Inter- Meaning: Indicates the ID of a parameter group
Para HoUtran CELLQ 01019/ RAT related to inter-RAT handover to UTRAN. This
GroupId CIPAR TDLOF Mobility parameter applies only to LTE FDD and LTE TDD.
A D-00101 between GUI Value Range: 0~9
MOD 9 E-
UTRAN Unit: None
CELLQ LOFD-0
CIPAR 01022/ and Actual Value Range: 0~9
A TDLOF UTRAN Default Value: 0
LST D-00102 SRVCC
CELLQ 2 to
CIPAR UTRAN
A
CellQci InterRat ADD LOFD-0 PS Inter- Meaning: Indicates the ID of a parameter group
Para HoGera CELLQ 01020/ RAT related to inter-RAT handover to GERAN. This
nGroupI CIPAR TDLOF Mobility parameter applies only to LTE FDD and LTE TDD.
d A D-00102 between GUI Value Range: 0~9
MOD 0 E-
UTRAN Unit: None
CELLQ LOFD-0
CIPAR 01023/ and Actual Value Range: 0~9
A TDLOF GERAN Default Value: 0
LST D-00102 SRVCC
CELLQ 3 to
CIPAR GERAN
A
CellQci Qci ADD LBFD-0 Basic Meaning: Indicates the QoS class identifier (QCI),
Para CELLQ 02025/ Scheduli which is an attribute of evolved packet system (EPS)
CIPAR TDLBF ng bearers. Different QCIs indicate different QoS
A D-00202 Dynami requirements, such as the packet delay budget, packet
LST 5 c loss rate (PLR) and packet error rate (PER), and
CELLQ LBFD-0 Scheduli resource type (whether the service is a GBR service or
CIPAR 0101502 ng not). For details, see Table 6.1.7 in 3GPP TS 23.203.
A / This parameter applies only to LTE FDD and LTE
TDLBF TDD.
MOD
CELLQ D-00101 GUI Value Range:
CIPAR 502 1,2,3,4,5,6,7,8,9,10~64,65,66,67~68,69,70,71~74,75,7
A 6~78,79,80~254
RMV Unit: None
CELLQ Actual Value Range:
CIPAR 1,2,3,4,5,6,7,8,9,10~64,65,66,67~68,69,70,71~74,75,7
A 6~78,79,80~254
Default Value: None
IntraRat A3Inter MOD LBFD-0 Coverag Meaning: Indicates the triggering quantity for events
HoCom FreqHo INTRA 0201802 e Based A1 and A2 related to A3-based inter-frequency
m A1A2Tr RATHO / Inter- handovers. RSRP measurements slightly vary with the
igQuan COMM TDLBF frequenc load, and there is little signal fluctuation. By contrast,
LST D-00201 y RSRQ measurements vary with the load and are likely
INTRA 802 Handov to reflect the signal quality of the cell in real time. If
RATHO er this parameter is set to BOTH, both RSRP- and
COMM RSRQ-based measurement configurations are
delivered. When either the RSRP-based or RSRQ-
based entering condition of event A1 or A2 is met, the
UE reports event A1 or A2. For details, see 3GPP TS
36.331.This parameter applies only to LTE FDD and
LTE TDD.
GUI Value Range: RSRP, RSRQ, BOTH
Unit: None
Actual Value Range: RSRP, RSRQ, BOTH
Default Value: RSRP
InterFre A3Inter ADD LBFD-0 Coverag Meaning: Indicates the RSRP threshold for event A2
qHoGro FreqHo INTERF 0201802 e Based of A3-based inter-frequency handover. When the
up A2ThdR REQHO / Inter- measured RSRP value exceeds this threshold, a
srp GROUP TDLBF frequenc measurement report will be sent. This parameter
MOD D-00201 y applies only to LTE FDD and LTE TDD.
INTERF 802 Handov GUI Value Range: -140~-43
REQHO LBFD-0 er
Unit: dBm
GROUP 0201801 Coverag
e Based Actual Value Range: -140~-43
LST
INTERF Intra- Default Value: -99
REQHO frequenc
GROUP y
Handov
er
InterFre A3Inter ADD LBFD-0 Coverag Meaning: Indicates the RSRQ threshold for event A2
qHoGro FreqHo INTERF 0201802 e Based of A3-based inter-frequency handover. This parameter
up A2ThdR REQHO / Inter- applies only to LTE FDD and LTE TDD.
srq GROUP TDLBF frequenc GUI Value Range: -40~-6
MOD D-00201 y
802 Handov Unit: 0.5dB
INTERF
REQHO er Actual Value Range: -20~-3
GROUP Default Value: -24
LST
INTERF
REQHO
GROUP
IntraRat InterFre MOD LBFD-0 Coverag Meaning: Indicates the triggering quantity for events
HoCom qHoA1 INTRA 0201802 e Based A1 and A2 related to A4- or A5-based inter-frequency
m A2Trig RATHO / Inter- handovers. RSRP measurements slightly vary with the
Quan COMM TDLBF frequenc load, and there is little signal fluctuation. By contrast,
LST D-00201 y RSRQ measurements vary with the load and are likely
INTRA 802 Handov to reflect the signal quality of the cell in real time. If
RATHO er this parameter is set to BOTH, both RSRP- and
COMM RSRQ-based measurement configurations are
delivered. When either the RSRP-based or RSRQ-
based entering condition of event A1 or A2 is met, the
UE reports event A1 or A2. For details, see 3GPP TS
36.331.This parameter applies only to LTE FDD and
LTE TDD.
GUI Value Range: RSRP, RSRQ, BOTH
Unit: None
Actual Value Range: RSRP, RSRQ, BOTH
Default Value: RSRP
LOFD-0 RAT
01021/ Mobility
TDLOF between
D-00102 E-
1 UTRAN
and
LOFD-0 GERAN
01111
PS Inter-
MLOFD RAT
-121280 Mobility
/ between
TDLEO E-
FD-121 UTRAN
611 and
CDMA2
000
PS
Mobility
from E-
UTRAN
to
CDMA2
000
HRPD
Based
on
Frequen
cy-
specific
Factors
eMTC
Introduc
tion
CellHoP BlindHo MOD LBFD-0 Coverag Meaning: Indicates the RSRQ threshold for events A1
araCfg A1A2Th CELLH 0201802 e Based and A2 related to coverage-based inter-frequency
dRsrq OPARA / Inter- blind handover and coverage-based inter-RAT blind
CFG TDLBF frequenc handover. If the RSRQ of the serving cell exceeds the
LST D-00201 y threshold, event A1 is reported. If the RSRQ of the
CELLH 802 Handov serving cell is lower than the threshold, event A2 is
OPARA LOFD-0 er reported. This parameter applies only to LTE FDD
CFG 01019/ PS Inter- and LTE TDD.
TDLOF RAT GUI Value Range: -40~-6
D-00101 Mobility Unit: 0.5dB
9 between
E- Actual Value Range: -20~-3
LOFD-0
01020/ UTRAN Default Value: -28
TDLOF and
D-00102 UTRAN
0 PS Inter-
LOFD-0 RAT
01021/ Mobility
TDLOF between
D-00102 E-
1 UTRAN
and
LOFD-0 GERAN
01111
PS Inter-
RAT
Mobility
between
E-
UTRAN
and
CDMA2
000
PS
Mobility
from E-
UTRAN
to
CDMA2
000
HRPD
Based
on
Frequen
cy-
specific
Factors
EutranIn InterFre ADD LBFD-0 Coverag Meaning: Indicates the event to trigger coverage-
terNFre qHoEve EUTRA 0201802 e Based based inter-frequency handovers. This parameter can
q ntType NINTE / Inter- be set to EventA3, EventA4, or EventA5. This
RNFRE TDLBF frequenc parameter applies only to LTE FDD and LTE TDD.
Q D-00201 y GUI Value Range: EventA3(EventA3),
MOD 802 Handov EventA4(EventA4), EventA5(EventA5)
EUTRA er
Unit: None
NINTE
RNFRE Actual Value Range: EventA3, EventA4, EventA5
Q Default Value: EventA4(EventA4)
LST
EUTRA
NINTE
RNFRE
Q
LBFD-0 to
02018/ GERAN
TDLBF Enhance
D-00201 d CS
8 Fallback
LOFD-0 to
01088/ CDMA2
TDLOF 000
D-00108 1xRTT
8 Mobility
Manage
ment
CS
Fallback
Steering
to
UTRAN
LBFD-0 to
02018/ GERAN
TDLBF Enhance
D-00201 d CS
8 Fallback
LOFD-0 to
01088/ CDMA2
TDLOF 000
D-00108 1xRTT
8 Mobility
Manage
ment
CS
Fallback
Steering
to
UTRAN
LBFD-0 to
02018/ GERAN
TDLBF Enhance
D-00201 d CS
8 Fallback
LOFD-0 to
01088/ CDMA2
TDLOF 000
D-00108 1xRTT
8 Mobility
Manage
ment
CS
Fallback
Steering
to
UTRAN
CellOp InterRat ADD LOFD-0 CS Meaning: Indicates the highest-priority target RAT for
HoCfg Highest CELLO 01033/ Fallback handovers. It is UTRAN by default. If this parameter
Pri PHOCF TDLOF to is set to UTRAN, GERAN, or CDMA2000, the
G D-00103 UTRAN highest-priority target RAT is UTRAN, GERAN, or
MOD 3 CS CDMA2000, respectively. This parameter applies only
CELLO LOFD-0 Fallback to LTE FDD and LTE TDD.
PHOCF 01034/ to GUI Value Range: UTRAN, GERAN, CDMA2000
G TDLOF GERAN Unit: None
LST D-00103 CS
4 Actual Value Range: UTRAN, GERAN, CDMA2000
CELLO Fallback
PHOCF LOFD-0 to Default Value: UTRAN
G 01035/ CDMA2
TDLOF 000
D-00103 1xRTT
5 PS Inter-
LOFD-0 RAT
01019/ Mobility
TDLOF between
D-00101 E-
9 UTRAN
and
LOFD-0
UTRAN
01020/
TDLOF PS Inter-
D-00102 RAT
0 Mobility
between
LOFD-0
E-
01021/
UTRAN
TDLOF
and
D-00102
GERAN
1
PS Inter-
LOFD-0
RAT
01052/
Mobility
TDLOF
between
D-00105
E-
2
UTRAN
LOFD-0 and
01053/ CDMA2
TDLOF 000
D-00105
Flash
3
CS
LOFD-0 Fallback
01090/ to
TDLOF UTRAN
D-00109 Flash
0 CS
Fallback
LOFD-0 to
70202 GERAN
LOFD-0 Enhance
81283/ d CS
TDLOF Fallback
D-08120 to
3 CDMA2
TDLOF 000
D-00108 1xRTT
8 Ultra-
Flash
CSFB to
UTRAN
Ultra-
Flash
CSFB to
GERAN
CS
Fallback
Steering
to
UTRAN
CellOp InterRat ADD LOFD-0 CS Meaning: Indicates the medium-priority target RAT
HoCfg SecondP CELLO 01033/ Fallback for handovers. It is GERAN by default. If this
ri PHOCF TDLOF to parameter is set to UTRAN, GERAN, or CDMA2000,
G D-00103 UTRAN the medium-priority target RAT is UTRAN, GERAN,
MOD 3 CS or CDMA2000, respectively. If this parameter is set to
CELLO LOFD-0 Fallback NULL, no medium-priority target RAT is specified
PHOCF 01034/ to and only the highest-priority target RAT can be
G TDLOF GERAN selected for handovers. This parameter applies only to
D-00103 LTE FDD and LTE TDD.
LST CS
CELLO 4 Fallback GUI Value Range: UTRAN, GERAN, CDMA2000,
PHOCF LOFD-0 to NULL
G 01035/ CDMA2 Unit: None
TDLOF 000 Actual Value Range: UTRAN, GERAN, CDMA2000,
D-00103 1xRTT NULL
5 PS Inter-
Default Value: GERAN
LOFD-0 RAT
01019/ Mobility
TDLOF between
D-00101 E-
9 UTRAN
and
LOFD-0
UTRAN
01020/
TDLOF PS Inter-
D-00102 RAT
0 Mobility
between
LOFD-0
E-
01021/
UTRAN
TDLOF
and
D-00102
GERAN
1
PS Inter-
LOFD-0
RAT
01052/
Mobility
TDLOF
between
D-00105
E-
2
UTRAN
LOFD-0 and
01053/ CDMA2
TDLOF 000
D-00105
Flash
3
CS
LOFD-0 Fallback
01090/ to
TDLOF UTRAN
D-00109 Flash
0 CS
Fallback
LOFD-0 to
70202 GERAN
LOFD-0 Enhance
81283/ d CS
TDLOF Fallback
D-08120 to
3 CDMA2
TDLOF 000
D-00108 1xRTT
8 Ultra-
Flash
CSFB to
UTRAN
Ultra-
Flash
CSFB to
GERAN
CS
Fallback
Steering
to
UTRAN
CellOp InterRat ADD LOFD-0 CS Meaning: Indicates the lowest-priority target RAT for
HoCfg LowestP CELLO 01033/ Fallback handovers. It is CDMA2000 by default. If this
ri PHOCF TDLOF to parameter is set to UTRAN, GERAN, or CDMA2000,
G D-00103 UTRAN the lowest-priority target RAT is UTRAN, GERAN,
MOD 3 CS or CDMA2000, respectively. If this parameter is set to
CELLO LOFD-0 Fallback NULL, no lowest-priority target RAT is specified and
PHOCF 01034/ to only the highest- or medium-priority target RAT can
G TDLOF GERAN be selected for handovers. This parameter applies only
D-00103 to LTE FDD and LTE TDD.
LST CS
CELLO 4 Fallback GUI Value Range: UTRAN, GERAN, CDMA2000,
PHOCF LOFD-0 to NULL
G 01035/ CDMA2 Unit: None
TDLOF 000 Actual Value Range: UTRAN, GERAN, CDMA2000,
D-00103 1xRTT NULL
5 PS Inter-
Default Value: CDMA2000
LOFD-0 RAT
01019/ Mobility
TDLOF between
D-00101 E-
9 UTRAN
and
LOFD-0
UTRAN
01020/
TDLOF PS Inter-
D-00102 RAT
0 Mobility
between
LOFD-0
E-
01021/
UTRAN
TDLOF
and
D-00102
GERAN
1
PS Inter-
LOFD-0
RAT
01052/
Mobility
TDLOF
between
D-00105
E-
2
UTRAN
LOFD-0 and
01053/ CDMA2
TDLOF 000
D-00105
Flash
3
CS
LOFD-0 Fallback
01090/ to
TDLOF UTRAN
D-00109 Flash
0 CS
Fallback
LOFD-0 to
70202 GERAN
LOFD-0 Enhance
81283/ d CS
TDLOF Fallback
D-08120 to
3 CDMA2
TDLOF 000
D-00108 1xRTT
8 Ultra-
Flash
CSFB to
UTRAN
Ultra-
Flash
CSFB to
GERAN
CS
Fallback
Steering
to
UTRAN
InterFre A3Inter ADD LBFD-0 Coverag Meaning: Indicates the RSRP threshold for event A1
qHoGro FreqHo INTERF 0201802 e Based of A3-based inter-frequency handover. When the
up A1ThdR REQHO / Inter- measured RSRP value exceeds this threshold, a
srp GROUP TDLBF frequenc measurement report will be sent. This parameter
MOD D-00201 y applies only to LTE FDD and LTE TDD.
INTERF 802 Handov GUI Value Range: -140~-43
REQHO LBFD-0 er
Unit: dBm
GROUP 0201801 Coverag
e Based Actual Value Range: -140~-43
LST
INTERF Intra- Default Value: -95
REQHO frequenc
GROUP y
Handov
er
InterFre A3Inter ADD LBFD-0 Coverag Meaning: Indicates the RSRQ threshold for event A1
qHoGro FreqHo INTERF 0201802 e Based of A3-based inter-frequency handover. This parameter
up A1ThdR REQHO / Inter- applies only to LTE FDD and LTE TDD.
srq GROUP TDLBF frequenc GUI Value Range: -40~-6
MOD D-00201 y
802 Handov Unit: 0.5dB
INTERF
REQHO er Actual Value Range: -20~-3
GROUP Default Value: -20
LST
INTERF
REQHO
GROUP
InterFre InterFre ADD LBFD-0 Coverag Meaning: Indicates the RSRP threshold for event A1
qHoGro qHoA1T INTERF 0201802 e Based of A4/A5-based inter-frequency handover. When the
up hdRsrp REQHO / Inter- measured RSRP value exceeds this threshold, a
GROUP TDLBF frequenc measurement report will be sent. This parameter
MOD D-00201 y applies only to LTE FDD and LTE TDD.
INTERF 802 Handov GUI Value Range: -140~-43
REQHO LBFD-0 er
Unit: dBm
GROUP 02018 Mobility
Manage Actual Value Range: -140~-43
LST
INTERF ment Default Value: -105
REQHO
GROUP
INTER_RAT_MLB_ALLOWED:On,
INTER_RAT_MLB_LOW_PRIO_IND:Off,
HO_USE_VOIP_FREQ_ALLOWED:Off,
SMART_CA_ALLOWED:Off,
ADMISSION_FORBIDDEN:Off
EutranIn VoipPrio ADD LBFD-0 Coverag Meaning: Indicates the frequency priority of providing
terNFre rity EUTRA 0201802 e Based VoIP services on the intra-RAT neighboring
q NINTE / Inter- frequency. A larger value of this parameter indicates a
RNFRE TDLBF frequenc higher priority. During coverage-based inter-
Q D-00201 y frequency handovers with VoipMeasFreqPriSwitch
MOD 802 Handov being on, the eNodeB selects and delivers the
EUTRA er neighboring frequencies based on the frequency
NINTE priorities when starting measurements. The eNodeB
RNFRE preferentially delivers the frequency with the highest
Q priorities to VoIP UEs. If this parameter is set to 0,
this neighboring frequency is not prioritized. This
LST parameter applies only to LTE FDD and LTE TDD.
EUTRA
NINTE GUI Value Range: 0~16
RNFRE Unit: None
Q Actual Value Range: 0~16
Default Value: 1
EutranIn PsPriorit ADD LBFD-0 Coverag Meaning: Indicates the priority of a neighboring E-
terNFre y EUTRA 0201802 e Based UTRAN frequency for carrying PS services. A large
q NINTE / Inter- value indicates a high priority. If
RNFRE TDLBF frequenc PsMeasFreqPriSwitch is on, the eNodeB
Q D-00201 y preferentially selects the neighboring E-UTRAN
MOD 802 Handov frequency with the highest PS service priority for
EUTRA er measurement during a coverage-based inter-frequency
NINTE handover procedure. If PsPriority is set to 0 for a
RNFRE frequency, this frequency is not prioritized. This
Q parameter applies only to LTE FDD and LTE TDD.
LST GUI Value Range: 0~16
EUTRA Unit: None
NINTE
Actual Value Range: 0~16
RNFRE
Q Default Value: 1
HeNbTa TacStart ADD LBFD-0 Mobility Meaning: Indicates the start TAC of the special TAC
cRange HENBT 02018/ Manage range group of HeNBs. This parameter value must be
Group ACRAN TDLBF ment less than or equal to the TacEnd parameter value.
GEGRO D-00201 3GPP specifications define that the TAC values
UP 8 0x0000(0) and 0xFFFE(65534) are reserved, and
MOD therefore these two TAC values cannot be used in later
HENBT versions. You are advised not to set 0 or 65534 as the
ACRAN TAC value in network planning and configuration.
GEGRO This parameter applies only to LTE FDD and LTE
UP TDD.
LST GUI Value Range: 1~65533,65535
HENBT Unit: None
ACRAN
Actual Value Range: 1~65533,65535
GEGRO
UP Default Value: None
HeNbTa TacEnd ADD LBFD-0 Mobility Meaning: Indicates the end TAC of the special TAC
cRange HENBT 02018/ Manage range group of HeNBs. This parameter value must be
Group ACRAN TDLBF ment greater than or equal to the TacStart parameter value.
GEGRO D-00201 3GPP specifications define that the TAC values
UP 8 0x0000(0) and 0xFFFE(65534) are reserved, and
MOD therefore these two TAC values cannot be used in later
HENBT versions. You are advised not to set 0 or 65534 as the
ACRAN TAC value in network planning and configuration.
GEGRO This parameter applies only to LTE FDD and LTE
UP TDD.
LST GUI Value Range: 1~65533,65535
HENBT Unit: None
ACRAN
Actual Value Range: 1~65533,65535
GEGRO
UP Default Value: None
IntraRat CovBas MOD LBFD-0 Coverag Meaning: Indicates the timer governing the period of
HoCom edIfHo INTRA 0201802 e Based time that the eNodeB waits for more measurement
m Waiting RATHO / Inter- reports to evaluate whether to perform a coverage-
Timer COMM TDLBF frequenc based inter-frequency handover after it receives a
LST D-00201 y measurement report. This parameter takes effect only
INTRA 802 Handov when the CovBasedInterFreqHoMode parameter is set
RATHO er to BASEDONSIGNALSTRENGTH or
COMM BASEDONFREQPRIORITY. This parameter applies
only to LTE FDD and LTE TDD.
GUI Value Range: 0~5000
Unit: ms
Actual Value Range: 0~5000
Default Value: 40
InterFre InterFre ADD LBFD-0 Coverag Meaning: Indicates the RSRP threshold for triggering
qHoGro qHoA4T INTERF 0201802 e Based a coverage-based inter-frequency measurement event.
up hdRsrp REQHO / Inter- When the measured RSRP value exceeds this
GROUP TDLBF frequenc threshold, an inter-frequency measurement report will
MOD D-00201 y be sent. Distance-based handover, uplink power-
INTERF 802 Handov control-based handover, SPID-based handover back to
REQHO LBFD-0 er the home PLMN, and speech-quality-based handover
GROUP 0201804 Distance also use this parameter as the RSRP threshold for
/ Based triggering an inter-frequency measurement event. This
LST parameter applies to A4 and A5 measurements. This
INTERF TDLBF Inter-
D-00201 frequenc parameter applies only to LTE FDD and LTE TDD.
REQHO
GROUP 804 y GUI Value Range: -140~-43
Handov Unit: dBm
er
Actual Value Range: -140~-43
Default Value: -105
EutranIn IfHoThd ADD LBFD-0 Coverag Meaning: Indicates the offset to the RSRP threshold
terNFre RsrpOff EUTRA 0201802 e Based for events A4 and A5 that trigger coverage-based
q set NINTE / Inter- inter-frequency handovers. In coverage-based
RNFRE TDLBF frequenc handovers, the eNodeB delivers the RSRP threshold
Q D-00201 y for event A4 or A5 to UEs, which is equal to the sum
MOD 802 Handov of the InterFreqHoA4ThdRsrp and
EUTRA er IfHoThdRsrpOffset parameter values. If the RSRP
NINTE threshold for event A4 or A5 is less than the minimum
RNFRE RSRP value, the minimum value is delivered instead.
Q If the RSRP threshold for event A4 or A5 is greater
than the maximum RSRP value, the maximum value
LST is delivered instead. This parameter applies only to
EUTRA LTE FDD and LTE TDD.
NINTE
RNFRE GUI Value Range: -20~20
Q Unit: dBm
Actual Value Range: -20~20
Default Value: 0
IntraRat InterFre MOD LBFD-0 Coverag Meaning: Indicates the quantity to be included in the
HoCom qHoA4 INTRA 0201802 e Based measurement report for inter-frequency handover
m RprtQua RATHO / Inter- events. The quantity can be RSRP, RSRQ, or both.
n COMM TDLBF frequenc The measured RSRP values are stable, slightly
LST D-00201 y varying with the load, and therefore there is little
INTRA 802 Handov signal fluctuation. The measured RSRQ values vary
RATHO LBFD-0 er with the load and are likely to reflect the signal quality
COMM 0201804 Distance of the cell in real time. This parameter applies to
/ Based measurements for event A4/A5. For details, see 3GPP
TDLBF Inter- TS 36.331. This parameter applies only to LTE FDD
D-00201 frequenc and LTE TDD.
804 y GUI Value Range: SAME_AS_TRIG_QUAN(Same
LBFD-0 Handov as Trig Quan), BOTH
0201805 er Unit: None
/ Service Actual Value Range: SAME_AS_TRIG_QUAN,
TDLBF Based BOTH
D-00201 Inter-
805 frequenc Default Value: SAME_AS_TRIG_QUAN(Same as
y Trig Quan)
Handov
er
InterFre InterFre ADD LBFD-0 Coverag Meaning: Indicates the RSRQ threshold for triggering
qHoGro qHoA4T INTERF 0201802 e Based a coverage-based inter-frequency measurement event.
up hdRsrq REQHO / Inter- When the measured RSRQ value exceeds this
GROUP TDLBF frequenc threshold, an inter-frequency measurement report will
MOD D-00201 y be sent. Distance-based handover, uplink power-
INTERF 802 Handov control-based handover, SPID-based handover back to
REQHO LBFD-0 er the home PLMN, and speech-quality-based handover
GROUP 0201804 Distance also use this parameter as the RSRQ threshold for
/ Based triggering an inter-frequency measurement event. This
LST parameter applies to A4 and A5 measurements. This
INTERF TDLBF Inter-
D-00201 frequenc parameter applies only to LTE FDD and LTE TDD.
REQHO
GROUP 804 y GUI Value Range: -40~-6
Handov Unit: 0.5dB
er
Actual Value Range: -20~-3
Default Value: -20
CnOper FirstRat MOD LBFD-0 Coverag Meaning: Indicates the priority of E-UTRAN TDD or
atorHoC Pri CNOPE 0201802 e Based E-UTRAN FDD in inter-frequency blind handover or
fg RATOR / Inter- blind redirection scenarios. To prioritize E-UTRAN
HOCFG TDLBF frequenc TDD or E-UTRAN FDD, set this parameter to
LST D-00201 y EUTRAN_TDD or EUTRAN_FDD, respectively. To
CNOPE 802 Handov treat E-UTRAN TDD and E-UTRAN FDD equally,
RATOR er set this parameter to EUTRAN. This parameter
HOCFG applies only to LTE FDD and LTE TDD.
GUI Value Range: EUTRAN_TDD, EUTRAN_FDD,
EUTRAN
Unit: None
Actual Value Range: EUTRAN_TDD,
EUTRAN_FDD, EUTRAN
Default Value: EUTRAN
CnOper Second MOD LBFD-0 Coverag Meaning: Indicates the priority of E-UTRAN TDD or
atorHoC RatPri CNOPE 0201802 e Based E-UTRAN FDD in inter-frequency blind handover or
fg RATOR / Inter- blind redirection scenarios. To prioritize E-UTRAN
HOCFG TDLBF frequenc TDD or E-UTRAN FDD, set this parameter to
LST D-00201 y EUTRAN_TDD or EUTRAN_FDD, respectively. If
CNOPE 802 Handov the FirstRatPri parameter is set to EUTRAN, the
RATOR er SecondRatPri parameter must be set to NULL,
HOCFG indicating that E-UTRAN TDD and E-UTRAN FDD
are not differentiated. This parameter applies only to
LTE FDD and LTE TDD.
GUI Value Range: EUTRAN_TDD, EUTRAN_FDD,
NULL
Unit: None
Actual Value Range: EUTRAN_TDD,
EUTRAN_FDD, NULL
Default Value: NULL
CellOp FirstRat ADD LBFD-0 Coverag Meaning: Indicates the priority of E-UTRAN TDD or
HoCfg Pri CELLO 0201802 e Based E-UTRAN FDD in inter-frequency blind handover or
PHOCF / Inter- blind redirection scenarios. To prioritize E-UTRAN
G TDLBF frequenc TDD or E-UTRAN FDD, set this parameter to
MOD D-00201 y EUTRAN_TDD or EUTRAN_FDD, respectively. To
CELLO 802 Handov treat E-UTRAN TDD and E-UTRAN FDD equally,
PHOCF er set this parameter to EUTRAN. This parameter
G applies only to LTE FDD and LTE TDD.
LST GUI Value Range: EUTRAN_TDD, EUTRAN_FDD,
CELLO EUTRAN
PHOCF Unit: None
G Actual Value Range: EUTRAN_TDD,
EUTRAN_FDD, EUTRAN
Default Value: EUTRAN
EutranIn BlindHo ADD LBFD-0 Coverag Meaning: Indicates the priority of the neighboring cell
terFreq Priority EUTRA 0201802 e Based during handovers. The parameter values are divided
NCell NINTE / Inter- into three segments, indicating the blind-handover
RFREQ TDLBF frequenc priority, frequency-based-handover priority, and 0.
NCELL D-00201 y Within the same segment, a larger parameter value
MOD 802 Handov indicates a higher priority. Blind handover is a process
EUTRA LBFD-0 er in which the eNodeB instructs a UE to hand over to a
NINTE 0201804 Distance specified neighboring cell without measurements. In a
RFREQ / Based blind handover, if this parameter is set to 0, this
NCELL TDLBF Inter- neighboring cell cannot be selected as a target cell. In
D-00201 frequenc a frequency-priority-based handover, if this parameter
LST is set to 0 and the eNodeB selects the frequencies to
EUTRA 804 y
Handov be delivered based on the blind handover cell
NINTE LBFD-1 configurations, this neighboring cell cannot be
RFREQ 31111/ er
selected as a target cell. The parameter values 1 to 16
NCELL TDLBF Mobility indicate the blind-handover priorities. The parameter
D-00105 between values 17 to 32 indicate the frequency-based-handover
0 LTE priorities for frequency-based blind handovers and
TDD measurement-based handovers. This parameter applies
and LTE only to LTE FDD and LTE TDD.
FDD
GUI Value Range: 0~32
Unit: None
Actual Value Range: 0~32
Default Value: 0
CellHoP CovBas MOD LBFD-0 Coverag Meaning: Indicates the threshold of the measurement
araCfg edIntraR CELLH 0201802 e Based duration for determining whether coverage-based
atMeasT OPARA / Inter- inter-frequency measurement has been performed for
ime CFG TDLBF frequenc emergency blind redirections. When event A2 for
LST D-00201 y blind redirections is reported, if the elapsed time after
CELLH 802 Handov the eNodeB delivers the last coverage-based inter-
OPARA er frequency measurement configurations exceeds this
CFG threshold, the eNodeB determines that coverage-based
inter-frequency measurement has been performed; if
the elapsed time is smaller than this threshold, the
eNodeB determines that no coverage-based inter-
frequency measurement is performed.
GUI Value Range: 0~100
Unit: s
Actual Value Range: 0~100
Default Value: 0
HeNbTa HeNbTa ADD LBFD-0 Mobility Meaning: Indicates the ID of the TAC range group of
cRange cRaGId HENBT 02018/ Manage HeNBs in macro-micro handover scenarios. This
Group ACRAN TDLBF ment parameter applies only to LTE FDD and LTE TDD.
GEGRO D-00201 GUI Value Range: 0~9
UP 8
Unit: None
LST
HENBT Actual Value Range: 0~9
ACRAN Default Value: None
GEGRO
UP
MOD
HENBT
ACRAN
GEGRO
UP
RMV
HENBT
ACRAN
GEGRO
UP
InterRat InterRat MOD LOFD-0 PS Inter- Meaning: Indicates the type of the inter-RAT
HoCom HoEvent INTER 01019/ RAT handover event. The event type can be B1 or B2. This
m Type RATHO TDLOF Mobility parameter applies only to coverage-based handovers.
COMM D-00101 between For details, see 3GPP TS 36.331. This parameter
LST 9 E- applies only to LTE FDD and LTE TDD.
INTER LOFD-0 UTRAN GUI Value Range: EventB1(EventB1),
RATHO 01020/ and EventB2(EventB2)
COMM TDLOF UTRAN
Unit: None
D-00102 PS Inter-
0 RAT Actual Value Range: EventB1, EventB2
Default Value: 0
Default Value: 0
InterRat InterRat ADD LOFD-0 PS Inter- Meaning: Indicates the RSRP threshold for inter-RAT
HoCom HoA1Th INTER 01019/ RAT measurement event A1. When the measured RSRP
mGroup dRsrp RATHO TDLOF Mobility value of the serving cell exceeds this threshold, an
COMM D-00101 between event A1 report will be sent. This parameter applies
GROUP 9 E- only to LTE FDD and LTE TDD.
MOD LOFD-0 UTRAN GUI Value Range: -140~-43
INTER 01020/ and
UTRAN Unit: dBm
RATHO TDLOF
COMM D-00102 PS Inter- Actual Value Range: -140~-43
GROUP 0 RAT Default Value: -111
LST LOFD-0 Mobility
INTER 01021/ between
RATHO TDLOF E-
COMM D-00102 UTRAN
GROUP 1 and
GERAN
LOFD-0
01022/ PS Inter-
TDLOF RAT
D-00102 Mobility
2 between
E-
TDLOF UTRAN
D-00102 and
3 CDMA2
LOFD-0 000
01111 SRVCC
to
UTRAN
SRVCC
to
GERAN
PS
Mobility
from E-
UTRAN
to
CDMA2
000
HRPD
Based
on
Frequen
cy-
specific
Factors
InterRat InterRat ADD LOFD-0 PS Inter- Meaning: Indicates the Ec/N0 threshold for event B1
HoUtran HoUtran INTER 01019/ RAT related to coverage-based inter-RAT handover to
Group B1ThdE RATHO TDLOF Mobility UTRAN. This parameter specifies the requirement for
cn0 UTRAN D-00101 between Ec/N0 of the target UTRAN cell. For a cell with large
GROUP 9 E- signal fading variance, set this parameter to a large
MOD LOFD-0 UTRAN value to prevent unnecessary handovers. For a cell
INTER 01022/ and with small signal fading variance, set this parameter to
RATHO TDLOF UTRAN a small value to ensure timely handovers. A large
UTRAN D-00102 SRVCC value of this parameter results in a low probability of
GROUP 2 to handover to the UTRAN cell, and a small value leads
UTRAN to a high probability. When the measurement value
LST LBFD-0 exceeds this threshold, a measurement report will be
INTER 02018/ Mobility sent. This parameter applies only to LTE FDD and
RATHO TDLBF Manage LTE TDD.
UTRAN D-00201 ment
GROUP 8 GUI Value Range: -48~0
Distance
LOFD-0 based Unit: 0.5dB
01072/ Inter- Actual Value Range: -24~0
TDLOF RAT Default Value: -24
D-00107 handove
2 r to
UTRAN
UtranN BlindHo ADD LOFD-0 PS Inter- Meaning: Indicates the priority of the neighboring cell
Cell Priority UTRAN 01019/ RAT during blind handovers. Blind handover is a process in
NCELL TDLOF Mobility which the eNodeB instructs a UE to hand over to a
MOD D-00101 between specified neighboring cell. There are 32 priorities
UTRAN 9 E- altogether. The priority has a positive correlation with
NCELL LOFD-0 UTRAN the value of this parameter. Note that the value 0
01033/ and indicates that blind handovers to the neighboring cell
LST UTRAN are not allowed. This parameter applies only to LTE
UTRAN TDLOF
D-00103 CS FDD and LTE TDD.
NCELL
3 Fallback GUI Value Range: 0~32
LOFD-0 to Unit: None
01052/ UTRAN
Actual Value Range: 0~32
TDLOF Flash
D-00105 CS Default Value: 0
2 Fallback
to
UTRAN
CellDrx CovGsm MOD TDLOF SRVCC Meaning: Indicates whether to deliver measurement-
Para MeasDr CELLD D-00102 to dedicated DRX parameters to a UE when GERAN
xCfgSwi RXPAR 3/ GERAN measurements are triggered for a coverage-based
tch A LOFD-0 PS Inter- handover of the UE. If this parameter is set to ON, the
LST 01023 RAT eNodeB delivers both DRX parameters and gap-
CELLD TDLOF Mobility assisted GERAN measurement configurations to the
RXPAR D-00102 between UE. If this parameter is set to OFF, the eNodeB
A 0/ E- delivers only gap-assisted GERAN measurement
LOFD-0 UTRAN configurations to the UE. This parameter applies only
01020 and to LTE FDD and LTE TDD.
LBFD-0 GERAN GUI Value Range: OFF(Off), ON(On)
02017/ DRX Unit: None
TDLBF
Actual Value Range: OFF, ON
D-00201
7 Default Value: OFF(Off)
GeranN BlindHo ADD LOFD-0 PS Inter- Meaning: Indicates the priority of the neighboring cell
cell Priority GERAN 01020/ RAT during blind handovers. Blind handover is a process in
NCELL TDLOF Mobility which the eNodeB instructs a UE to hand over to a
MOD D-00102 between specified neighboring cell. There are 32 priorities
GERAN 0 E- altogether. The priority has a positive correlation with
NCELL LOFD-0 UTRAN the value of this parameter. Note that the value 0
01023/ and indicates that blind handovers to the neighboring cell
LST GERAN are not allowed. This parameter applies only to LTE
GERAN TDLOF
D-00102 SRVCC FDD and LTE TDD.
NCELL
3 to GUI Value Range: 0~32
LOFD-0 GERAN Unit: None
01034/ CS Actual Value Range: 0~32
TDLOF Fallback
D-00103 to Default Value: 0
4 GERAN
LOFD-0 Flash
01053/ CS
TDLOF Fallback
D-00105 to
3 GERAN
GeranRa BcchGr ADD LOFD-0 RAN Meaning: Indicates the index of the GERAN carrier
nShare oupId GERAN 01036/ Sharing frequency group. It uniquely identifies a GERAN
RANSH TDLOF with carrier frequency group. This parameter applies only
ARE D-00103 Commo to LTE FDD and LTE TDD.
LST 6 n GUI Value Range: 0~31
GERAN LOFD-0 Carrier
Unit: None
RANSH 01112/ MOCN
ARE TDLOF Flexible Actual Value Range: 0~31
UtranNF PsPriorit ADD LOFD-0 PS Inter- Meaning: Indicates the priority for the neighboring
req y UTRAN 01019/ RAT UTRAN frequency to carry PS services. In coverage-
NFREQ TDLOF Mobility based inter-RAT PS handovers, if
MOD D-00101 between UtranFreqLayerMeasSwitch is turned on, the eNodeB
UTRAN 9 E- determines the UTRAN frequency to be delivered to a
NFREQ LOFD-0 UTRAN UE based on PS service priorities. The eNodeB
01078/ and delivers the UTRAN frequency with the highest PS
LST UTRAN priority to the UE by default.In blind handovers to
UTRAN TDLOF
D-00107 E- UTRAN, the target cell for a blind handover is
NFREQ selected based on PS service priorities. The cell on the
8 UTRAN
to UTRAN frequency with the highest PS priority is
LBFD-0 selected by default.When this parameter is set to
02018 UTRAN
CS/PS Priority_0 for a UTRAN frequency, the UTRAN
Steering frequency is not included in PS service priority
arrangement. This parameter applies only to LTE FDD
Mobility and LTE TDD.
Manage
ment GUI Value Range: Priority_0(Priority 0),
Priority_1(Priority 1), Priority_2(Priority 2),
Priority_3(Priority 3), Priority_4(Priority 4),
Priority_5(Priority 5), Priority_6(Priority 6),
Priority_7(Priority 7), Priority_8(Priority 8),
Priority_9(Priority 9), Priority_10(Priority 10),
Priority_11(Priority 11), Priority_12(Priority 12),
Priority_13(Priority 13), Priority_14(Priority 14),
Priority_15(Priority 15), Priority_16(Priority 16)
Unit: None
Actual Value Range: Priority_0, Priority_1,
Priority_2, Priority_3, Priority_4, Priority_5,
Priority_6, Priority_7, Priority_8, Priority_9,
Priority_10, Priority_11, Priority_12, Priority_13,
Priority_14, Priority_15, Priority_16
Default Value: Priority_2(Priority 2)
UtranNF CsPriori ADD LOFD-0 E- Meaning: Indicates the circuit switched (CS) priority
req ty UTRAN 01078/ UTRAN of the neighboring UTRAN frequency, that is, the
NFREQ TDLOF to priority for the neighboring UTRAN frequency to
MOD D-00107 UTRAN carry CS services. During CSFB-based CS service
UTRAN 8 CS/PS handovers with UtranFreqLayerMeasSwitch being on,
NFREQ LOFD-0 Steering the eNodeB selects and delivers the neighboring
01033/ CS UTRAN frequencies based on the CS priorities when
LST starting measurements. The eNodeB preferentially
UTRAN TDLOF Fallback
D-00103 to delivers the UTRAN frequency with the highest CS
NFREQ priority to measure. During CSFB-based CS service
3 UTRAN
handovers with UtranFreqLayerBlindSwitch being on,
LOFD-0 Flash the eNodeB selects the target cells for blind handovers
01052/ CS on neighboring UTRAN frequencies based on the CS
TDLOF Fallback priorities and preferentially selects the target cell for
D-00105 to blind handovers on the neighboring UTRAN
2 UTRAN frequency with the highest CS priorities. If this
LOFD-0 CS parameter is set to Priority_0, this neighboring
01088/ Fallback UTRAN frequency is not prioritized. This parameter
TDLOF Steering applies only to LTE FDD and LTE TDD.
D-00108 to GUI Value Range: Priority_0(Priority 0),
8 UTRAN Priority_1(Priority 1), Priority_2(Priority 2),
Priority_3(Priority 3), Priority_4(Priority 4),
Priority_5(Priority 5), Priority_6(Priority 6),
Priority_7(Priority 7), Priority_8(Priority 8),
Priority_9(Priority 9), Priority_10(Priority 10),
Priority_11(Priority 11), Priority_12(Priority 12),
Priority_13(Priority 13), Priority_14(Priority 14),
Priority_15(Priority 15), Priority_16(Priority 16)
Unit: None
Actual Value Range: Priority_0, Priority_1,
Priority_2, Priority_3, Priority_4, Priority_5,
Priority_6, Priority_7, Priority_8, Priority_9,
Priority_10, Priority_11, Priority_12, Priority_13,
Priority_14, Priority_15, Priority_16
Default Value: Priority_2(Priority 2)
CnOper ServiceI ADD LBFD-0 Service Meaning: Indicates the ID of a service-based inter-
atorQciP fHoCfg CNOPE 0201805 Based frequency handover policy group. This parameter
ara GroupId RATOR / Inter- applies only to LTE FDD and LTE TDD.
QCIPA TDLBF frequenc GUI Value Range: 0~9
RA D-00201 y
805 Handov Unit: None
MOD
CNOPE er Actual Value Range: 0~9
RATOR Default Value: 0
QCIPA
RA
LST
CNOPE
RATOR
QCIPA
RA
ServiceI ServiceI ADD LBFD-0 Service Meaning: Indicates the ID of the service-based or
fHoCfg fHoCfg SERVIC 0201805 Based service-request-based inter-frequency handover policy
Group GroupId EIFHO / Inter- group. This parameter applies only to LTE FDD and
CFGGR TDLBF frequenc LTE TDD.
OUP D-00201 y GUI Value Range: 0~9
LST 805 Handov
er Unit: None
SERVIC TDLOF
EIFHO D-07022 Service- Actual Value Range: 0~9
CFGGR 8 Request Default Value: None
OUP Based
MOD Inter-
SERVIC frequenc
EIFHO y
CFGGR Handov
OUP er
RMV
SERVIC
EIFHO
CFGGR
OUP
ServiceI InterFre ADD LBFD-0 Service Meaning: Indicates whether to allow service-based or
fHoCfg qHoStat SERVIC 0201805 Based service-request-based inter-frequency handovers of
Group e EIFHO / Inter- the policy group to a specified frequency. If this
CFGGR TDLBF frequenc parameter is set to NO_HO, service-based or service-
OUP D-00201 y request-based inter-frequency handovers of services
MOD 805 Handov with a specific QCI to a specified frequency are not
SERVIC TDLOF er allowed. If this parameter is set to PERMIT_HO, such
EIFHO D-07022 Service- handovers are allowed. This parameter applies only to
CFGGR 8 Request LTE FDD and LTE TDD.
OUP Based GUI Value Range: NO_HO, PERMIT_HO
LST Inter- Unit: None
SERVIC frequenc
y Actual Value Range: NO_HO, PERMIT_HO
EIFHO
CFGGR Handov Default Value: NO_HO
OUP er
ServiceI ServiceI ADD LBFD-0 Service Meaning: Indicates the ID of the service-based inter-
fDlEarfc fHoCfg SERVIC 0201805 Based frequency handover policy group. This parameter
nGrp GroupId EIFDLE / Inter- applies only to LTE FDD and LTE TDD.
ARFCN TDLBF frequenc GUI Value Range: 0~9
GRP D-00201 y
805 Handov Unit: None
LST
SERVIC TDLOF er Actual Value Range: 0~9
EIFDLE D-07022 Service- Default Value: None
ARFCN 8 Request
GRP Based
MOD Inter-
SERVIC frequenc
EIFDLE y
ARFCN Handov
GRP er
RMV
SERVIC
EIFDLE
ARFCN
GRP
ServiceI Service ADD LBFD-0 Service Meaning: Indicates the priority for the frequency to be
fDlEarfc HoFreq SERVIC 0201805 Based the target frequency for service-based and service-
nGrp Priority EIFDLE / Inter- request-based inter-frequency handovers. A larger
ARFCN TDLBF frequenc value indicates a higher priority. When setting
GRP D-00201 y measurement configurations for service-based and
MOD 805 Handov service-request-based inter-frequency handovers, the
SERVIC er eNodeB selects the neighboring E-UTRA frequencies
EIFDLE in descending order of priority. This parameter applies
ARFCN only to LTE FDD and LTE TDD.
GRP GUI Value Range: 0~15
LST Unit: None
SERVIC Actual Value Range: 0~15
EIFDLE
ARFCN Default Value: 3
GRP
InterFre InterFre ADD LBFD-0 Service Meaning: Indicates the RSRP threshold for event A4
qHoGro qLoadB INTERF 0201805 Based related to load-based inter-frequency handovers.
up asedHo REQHO / Inter- When the measured RSRP value exceeds this
A4ThdR GROUP TDLBF frequenc threshold, event A4 is reported. This parameter also
srp MOD D-00201 y specifies the RSRP threshold for inter-frequency event
INTERF 805 Handov A4 related to frequency-priority-based handovers,
REQHO er service-based handovers, handovers of low-mobility
GROUP UEs, or redirection of high-mobility UEs. This
parameter applies only to LTE FDD and LTE TDD.
LST
INTERF GUI Value Range: -140~-43
REQHO Unit: dBm
GROUP Actual Value Range: -140~-43
Default Value: -103
EutranIn IfSrvHo ADD LBFD-0 Service Meaning: Indicates the offset of the RSRP threshold
terNFre ThdRsrp EUTRA 0201805 Based for triggering service-based inter-frequency
q Offset NINTE / Inter- handovers. In service-based inter-frequency
RNFRE TDLBF frequenc handovers, the eNodeB delivers the RSRP threshold
Q D-00201 y for event A4 or A5 to UEs, which is equal to the sum
MOD 805 Handov of the InterFreqLoadBasedHoA4ThdRsrp and
EUTRA TDLOF er IfSrvHoThdRsrpOffset parameter values. In service-
NINTE D-07022 Service- request-based inter-frequency handovers, the eNodeB
RNFRE 8 Request delivers the RSRP threshold for event A4 or A5 to
Q Based UEs, which is equal to the sum of the
Inter- SrvReqHoA4ThdRsrp and IfSrvHoThdRsrpOffset
LST parameter values. If the RSRP threshold for event A4
EUTRA frequenc
y or A5 is less than the minimum RSRP value, the
NINTE minimum value is delivered instead. If the RSRP
RNFRE Handov
er threshold for event A4 or A5 is greater than the
Q maximum RSRP value, the maximum value is
delivered instead. This parameter applies only to LTE
FDD and LTE TDD.
GUI Value Range: -20~20
Unit: dBm
Actual Value Range: -20~20
Default Value: 0
IntraRat InterFre MOD LBFD-0 Distance Meaning: Indicates the triggering quantity for events
HoCom qHoA4T INTRA 0201804 Based A4 and A5 related to all non-coverage-based inter-
m rigQuan RATHO / Inter- frequency handovers. RSRP measurements slightly
COMM TDLBF frequenc vary with the load, and there is little signal fluctuation.
LST D-00201 y By contrast, RSRQ measurements vary with the load
INTRA 804 Handov and are likely to reflect the signal quality of the cell in
RATHO LBFD-0 er real time. If this parameter is set to BOTH, both
COMM 0201805 Service RSRP- and RSRQ-based A4 or A5 measurement
/ Based configurations are delivered. When either the RSRP-
TDLBF Inter- based or RSRQ-based entering condition of event A4
D-00201 frequenc or A5 is met, the UE reports event A4 or A5. This
805 y parameter applies only to LTE FDD and LTE TDD.
Handov GUI Value Range: RSRP, RSRQ, BOTH
er Unit: None
Actual Value Range: RSRP, RSRQ, BOTH
Default Value: RSRP
InterFre InterFre ADD LBFD-0 Service Meaning: Indicates the RSRQ threshold for event A4
qHoGro qLoadB INTERF 0201805 Based related to load-based inter-frequency handovers.
up asedHo REQHO / Inter- When the measured RSRQ value exceeds this
A4ThdR GROUP TDLBF frequenc threshold, event A4 is reported. This parameter also
srq MOD D-00201 y specifies the RSRQ threshold for inter-frequency
INTERF 805 Handov event A4 related to frequency-priority-based
REQHO er handovers, service-based handovers, handovers of
GROUP low-mobility UEs, or redirection of high-mobility
UEs. This parameter applies only to LTE FDD and
LST LTE TDD.
INTERF
REQHO GUI Value Range: -40~-6
GROUP Unit: 0.5dB
Actual Value Range: -20~-3
Default Value: -18
EutranIn IfSrvHo ADD LBFD-0 Service Meaning: Indicates the offset of the RSRQ threshold
terNFre ThdRsrq EUTRA 0201805 Based for triggering service-based inter-frequency
q Offset NINTE / Inter- handovers. In service-based inter-frequency
RNFRE TDLBF frequenc handovers, the eNodeB delivers the RSRQ threshold
Q D-00201 y for event A4 or A5 to UEs, which is equal to the sum
MOD 805 Handov of the InterFreqLoadBasedHoA4ThdRsrq and
EUTRA TDLOF er IfSrvHoThdRsrqOffset parameter values. In service-
NINTE D-07022 Service- request-based inter-frequency handovers, the eNodeB
RNFRE 8 Request delivers the RSRQ threshold for event A4 or A5 to
Q Based UEs, which is equal to the sum of the
Inter- SrvReqHoA4ThdRsrq and IfSrvHoThdRsrqOffset
LST parameter values. If the RSRQ threshold for event A4
EUTRA frequenc
y or A5 is less than the minimum RSRQ value, the
NINTE minimum value is delivered instead. If the RSRQ
RNFRE Handov
er threshold for event A4 or A5 is greater than the
Q maximum RSRQ value, the maximum value is
delivered instead. This parameter applies only to LTE
FDD and LTE TDD.
GUI Value Range: -20~20
Unit: 0.5dB
Actual Value Range: -10~10
Default Value: 0
EutranIn OverlapI ADD LOFD-0 Intra- Meaning: Indicates whether the neighboring cell is
terFreq nd EUTRA 01032/ LTE identified as a neighboring cell overlapping the local
NCell NINTE TDLOF Load E-UTRAN cell. The default value is NO. The
RFREQ D-00103 Balancin parameter value YES indicates that the neighboring
NCELL 2 g cell is identified as a neighboring cell overlapping the
MOD LOFD-0 Automat local E-UTRAN cell. The parameter value NO
EUTRA 02001/ ic indicates that the neighboring cell is not identified as a
NINTE TDLOF Neighbo neighboring cell overlapping the local E-UTRAN cell.
RFREQ D-00200 ur This parameter applies only to LTE FDD and LTE
NCELL 1 Relation TDD.
DSP LOFD-0 (ANR) GUI Value Range: NO(NO), YES(YES)
EUTRA 70215/ Intra- Unit: None
NEXTE TDLOF LTE Actual Value Range: NO, YES
NDEDN D-07021 User
CELL 5 Number Default Value: NO(NO)
DSP Load
EUTRA Balancin
NINTE g
RFREQ
NCELL
LST
EUTRA
NINTE
RFREQ
NCELL
CellML InterFre MOD LOFD-0 Intra- Meaning: Indicates the threshold of the number of
B qMlbUe CELLM 70215/ LTE synchronized UEs for triggering inter-frequency load
NumTh LB TDLOF User balancing. When the MlbTriggerMode parameter is
d LST D-07021 Number set to UE_NUMBER_ONLY(UeNumMode) or
CELLM 5 Load PRB_OR_UE_NUMBER(PrbOrUeNumMode), inter-
LB Balancin frequency load balancing is triggered if the number of
g synchronized UEs in the cell is greater than or equal
to the sum of the InterFreqMlbUeNumThd and
MlbUeNumOffset parameter values. Inter-frequency
load balancing stops if the number of synchronized
UEs in the cell is less than the
InterFreqMlbUeNumThd parameter value. This
parameter applies only to LTE FDD and LTE TDD.
GUI Value Range: 1~10000
Unit: None
Actual Value Range: 1~10000
Default Value: 100
CellML InterFrq MOD LOFD-0 Intra- Meaning: Indicates the UL-synchronized UE number
B UeNum CELLM 01032/ LTE threshold used for transferring UEs to neighboring
Offload LB TDLOF Load cells with which the source cell does not exchange
Offset LST D-00103 Balancin load information during inter-frequency MLB.
CELLM 2 g Consider that the MlbTriggerMode parameter is set to
LB LOFD-0 Operator UE_NUMBER_ONLY(UeNumMode) or
70204/ Load PRB_OR_UE_NUMBER(PrbOrUeNumMode). If the
TDLOF Based number of UL-synchronized UEs in the source cell is
D-13121 Intra- greater than or equal to the sum of the
1 LTE InterFreqMlbUeNumThd parameter value and the
MLB InterFrqUeNumOffloadOffset parameter value,
LOFD-0 neighboring cells with which the source cell does not
70215/ Intra- exchange load information can be selected as the
TDLOF LTE target cells for MLB, and the source cell rejects
D-07021 User incoming load-based handover requests. If the number
5 Number of UL-synchronized UEs in the source cell is less than
Load the value calculated by the InterFreqMlbUeNumThd
Balancin parameter value plus the InterFrqUeNumOffloadOff-
g set parameter value and then minus the LoadOffset
parameter value, the source cell allows incoming load-
based handovers. This parameter applies only to LTE
FDD and LTE TDD.
GUI Value Range: 0~10000
Unit: None
Actual Value Range: 0~10000
Default Value: 0
GbrAmbrJudgeSwitch, MtaAlgSwitch,
RelaxedBackhaulCaSwitch, AdpCaSwitch,
CaHoControlSwitch, DistributeCloudbbCaSwitch,
SccSmartCfgSwitch, IdleModePccAnchorSwitch,
FreqPriBasedHoCaFiltSwitch, CaSccSuspendSwitch,
PccSmartCfgSwitch, CaA5HoEventSwitch,
EnhancedPccAnchorSwitch, CaAdpPreSchSwitch,
CaPreSchSwitch, CaLoadBalancePreAllocSwitch,
RelaxedBHCaArqSelectSwitch,
TddRelaxedBackhaulCaSwitch, RelaxedBHCaEnhan-
ceSwitch, CaSmartSelectionSwitch,
CaRlcPreAllocSwitch, PccAnchorOptSwitch
Default Value: PdcchOverlapSrchSpcSwitch:On,
CaCapbFiltSwitch:Off, PccAnchorSwitch:Off,
SccBlindCfgSwitch:Off, FreqCfgSwitch:Off,
SccA2RmvSwitch:On, CaTrafficTriggerSwitch:Off,
HoWithSccCfgSwitch:Off, SccModA6Switch:Off,
GbrAmbrJudgeSwitch:Off, MtaAlgSwitch:Off,
RelaxedBackhaulCaSwitch:Off, AdpCaSwitch:Off,
CaHoControlSwitch:Off, DistributeCloudbbCaS-
witch:Off, SccSmartCfgSwitch:Off,
IdleModePccAnchorSwitch:Off, FreqPriBasedHoCa-
FiltSwitch:Off, CaSccSuspendSwitch:Off,
PccSmartCfgSwitch:Off, CaA5HoEventSwitch:On,
EnhancedPccAnchorSwitch:Off,
CaAdpPreSchSwitch:On, CaPreSchSwitch:Off,
CaLoadBalancePreAllocSwitch:Off,
RelaxedBHCaArqSelectSwitch:Off,
TddRelaxedBackhaulCaSwitch:Off,
RelaxedBHCaEnhanceSwitch:Off,
CaSmartSelectionSwitch:Off,
CaRlcPreAllocSwitch:On, PccAnchorOptSwitch:Off
Handov
er
ENodeB Service MOD LBFD-0 Service Meaning: Indicates whether services in a service
AlgoSwi HoMulti ENODE 0201805 Based group can be transferred to different E-UTRAN
tch TargetFr BALGO / Inter- frequencies by service-based handovers. If this
eqSw SWITC TDLBF frequenc parameter is set to ON, services in a service group can
H D-00201 y be transferred to different E-UTRAN frequencies
LST 805 Handov specified in the ServiceIfDlEarfcnGrp MO. If this
ENODE er parameter is set to OFF, services in a service group
BALGO can be transferred only to the frequency with an index
SWITC of 0. This parameter applies only to LTE FDD.
H GUI Value Range: OFF(Off), ON(On)
Unit: None
Actual Value Range: OFF, ON
Default Value: OFF(Off)
CnOper ServiceI ADD LOFD-0 Service Meaning: Indicates the ID of a service-based inter-
atorQciP rHoCfg CNOPE 01043/ based RAT handover policy group. This parameter applies
ara GroupId RATOR TDLOF Inter- only to LTE FDD and LTE TDD.
QCIPA D-00104 RAT GUI Value Range: 0~9
RA 3 handove
r to Unit: None
MOD LOFD-0
CNOPE 01046/ UTRAN Actual Value Range: 0~9
RATOR TDLOF Service Default Value: 0
QCIPA D-00104 based
RA 6 Inter-
LST RAT
CNOPE handove
RATOR r to
QCIPA GERAN
RA
ServiceI ServiceI ADD LOFD-0 Service Meaning: Indicates the ID of the service-based inter-
rHoCfg rHoCfg SERVIC 01043/ based RAT handover policy group. This parameter applies
Group GroupId EIRHO TDLOF Inter- only to LTE FDD and LTE TDD.
CFGGR D-00104 RAT GUI Value Range: 0~9
OUP 3 handove
r to Unit: None
LST LOFD-0
SERVIC 01046/ UTRAN Actual Value Range: 0~9
EIRHO TDLOF Service Default Value: None
CFGGR D-00104 based
OUP 6 Inter-
MOD RAT
SERVIC handove
EIRHO r to
CFGGR GERAN
OUP
RMV
SERVIC
EIRHO
CFGGR
OUP
ServiceI InterRat ADD LOFD-0 Service Meaning: Indicates whether service-based inter-RAT
rHoCfg HoState SERVIC 01043/ based handovers are forbidden, allowed, or required for
Group EIRHO TDLOF Inter- services with the QCI. If this parameter is set to
CFGGR D-00104 RAT NO_HO, service-based inter-RAT handovers of this
OUP 3 handove policy group are forbidden. If this parameter is set to
MOD LOFD-0 r to PERMIT_HO, such handovers are allowed but not
SERVIC 01046/ UTRAN proactively initiated. If this parameter is set to
EIRHO TDLOF Service MUST_HO, such handovers must be initiated. This
CFGGR D-00104 based parameter applies only to LTE FDD and LTE TDD.
OUP 6 Inter- GUI Value Range: NO_HO, PERMIT_HO,
LST RAT MUST_HO
SERVIC handove Unit: None
EIRHO r to
GERAN Actual Value Range: NO_HO, PERMIT_HO,
CFGGR MUST_HO
OUP
Default Value: NO_HO
CellHoP SrvccMr MOD LOFD-0 SRVCC Meaning: Indicates the length of the processing delay
araCfg DelayTi CELLH 01022/ to timer of inter-RAT handover measurement reports that
mer OPARA TDLOF UTRAN UEs send when running QCI-1 services. This timer
CFG D-00102 SRVCC starts when a VoLTE service is successfully set up. It
LST 2 to is used to avoid SRVCC before phones ring or users
CELLH LOFD-0 GERAN answer calls. This parameter applies only to LTE FDD
OPARA 01023/ and LTE TDD.
CFG TDLOF GUI Value Range: 0~20
D-00102 Unit: s
3
Actual Value Range: 0~20
Default Value: 0
CellAlg DistBas MOD LBFD-0 Distance Meaning: Indicates the switch used to enable or
oSwitch edHoSw CELLA 0201804 Based disable distance-based handovers. If this switch is
itch LGOSW / Inter- turned on, distance-based handovers are allowed. If
ITCH TDLBF frequenc this switch is turned off, distance-based handovers are
LST D-00201 y prohibited. This parameter applies only to LTE FDD
CELLA 804 Handov and LTE TDD.
LGOSW LOFD-0 er GUI Value Range: OFF(Off), ON(On)
ITCH 01072/ Distance Unit: None
TDLOF based
D-00107 Inter- Actual Value Range: OFF, ON
2 RAT Default Value: OFF(Off)
LOFD-0 handove
01073/ r to
TDLOF UTRAN
D-00107 Distance
3 based
Inter-
RAT
handove
r to
GERAN
DistBas DistBas MOD LOFD-0 Distance Meaning: Indicates the measurement object type for
edHO edMeas DISTB 01072/ based distance-based handovers. The measurement object
ObjType ASEDH TDLOF Inter- type can be E-UTRAN, UTRAN, or GERAN. This
O D-00107 RAT parameter applies only to LTE FDD and LTE TDD.
LST 2 handove GUI Value Range: EUTRAN, GERAN, UTRAN
DISTB LOFD-0 r to
UTRAN Unit: None
ASEDH 01073/
O TDLOF Distance Actual Value Range: EUTRAN, GERAN, UTRAN
D-00107 based Default Value: EUTRAN:Off, GERAN:Off,
3 Inter- UTRAN:Off
LBFD-0 RAT
0201804 handove
/ r to
TDLBF GERAN
D-00201 Distance
804 Based
Inter-
frequenc
y
Handov
er
DistBas DistBas MOD LBFD-0 Distance Meaning: Indicates the threshold for distance-based
edHO edHOTh DISTB 0201804 Based handovers. If the distance between a UE and the cell
d ASEDH / Inter- center is greater than this threshold, a distance-based
O TDLBF frequenc handover is triggered for this UE. This parameter
LST D-00201 y applies only to LTE FDD and LTE TDD.
DISTB 804 Handov GUI Value Range: 1~1000
ASEDH LOFD-0 er
Unit: 100m
O 01072/ Distance
TDLOF based Actual Value Range: 100~100000
D-00107 Inter- Default Value: 10
2 RAT
LOFD-0 handove
01073/ r to
TDLOF UTRAN
D-00107 Distance
3 based
Inter-
RAT
handove
r to
GERAN
CellHoP UlBadQ MOD LBFD-0 Mobility Meaning: Indicates the MCS index threshold for
araCfg ualHoM CELLH 02018 Manage triggering uplink-quality-based handovers. If the
csThd OPARA ment uplink MCS index selected for a UE is less than the
CFG UlBadQualHoMcsThd parameter value, the eNodeB
LST measures the uplink IBLER of the UE. The eNodeB
CELLH determines whether to trigger an uplink-quality-based
OPARA handover for a UE based on the measurement result. If
CFG the selected uplink MCS index is greater than the
UlBadQualHoMcsThd parameter value, the uplink-
quality-based handover is terminated for the UE. This
parameter applies only to LTE FDD and LTE TDD.
GUI Value Range: 0~28
Unit: None
Actual Value Range: 0~28
Default Value: 5
CellHoP UlBadQ MOD LBFD-0 Mobility Meaning: Indicates the IBLER threshold for triggering
araCfg ualHoIbl CELLH 02018 Manage uplink-quality-based handovers. If the uplink IBLER
erThd OPARA ment of a UE minus the target IBLER is greater than the
CFG UlBadQualHoIblerThd parameter value, an uplink-
LST quality-based handover is triggered for the UE. If the
CELLH uplink IBLER of a UE minus the target IBLER and
OPARA minus 10% is greater than the UlBadQualHoIblerThd
CFG parameter value, an uplink-quality-based blind
handover is triggered for the UE. If the uplink IBLER
of a UE minus the target IBLER is less than the
UlBadQualHoIblerThd parameter value, the uplink-
quality-based handover is terminated for the UE. This
parameter applies only to LTE FDD and LTE TDD.
GUI Value Range: 0~100
Unit: %
Actual Value Range: 0~100
Default Value: 20
InterFre UlBadQ ADD LBFD-0 Mobility Meaning: Indicates the offset of the A4 threshold of
qHoGro ualHoA INTERF 02018/ Manage the target cell related to UL-quality-based inter-
up 4Offset REQHO TDLBF ment frequency handovers to the A4 threshold related to
GROUP D-00201 coverage-based inter-frequency handovers. This offset
MOD 8 applies to RSRP- and RSRQ-based A4 thresholds.
INTERF The actual threshold for event A4 is equal to the sum
REQHO of the threshold for event A4 related to coverage-
GROUP based inter-frequency handovers and the
UlBadQualHoA4Offset parameter value. If the sum is
LST less than the 3GPP-defined minimum value or greater
INTERF than the 3GPP-defined maximum value, the 3PGG-
REQHO defined minimum or maximum value is delivered,
GROUP respectively. This parameter applies only to LTE FDD
and LTE TDD.
GUI Value Range: -20~20
Unit: None
Actual Value Range: -20~20
Default Value: 0
ServiceI DlEarfc ADD LBFD-0 Service Meaning: Indicates the index of a DL EARFCN in a
fDlEarfc nIndex SERVIC 0201805 Based DL EARFCN group for service-based inter-frequency
nGrp EIFDLE / Inter- handover. This parameter applies only to LTE FDD
ARFCN TDLBF frequenc and LTE TDD.
GRP D-00201 y GUI Value Range: 0~15
LST 805 Handov
er Unit: None
SERVIC TDLOF
EIFDLE D-07022 Service- Actual Value Range: 0~15
ARFCN 8 Request Default Value: None
GRP Based
MOD Inter-
SERVIC frequenc
EIFDLE y
ARFCN Handov
GRP er
RMV
SERVIC
EIFDLE
ARFCN
GRP
CellML InterFre MOD LOFD-0 Intra- Meaning: Indicates the threshold of the downlink PRB
B qMlbTh CELLM 01032/ LTE usage for triggering inter-frequency MLB. If the
d LB TDLOF Load MlbTriggerMode parameter is set to
LST D-00103 Balancin PRB_ONLY(PrbMode) or
CELLM 2 g PRB_OR_UE_NUMBER(PrbOrUeNumMode), inter-
LB frequency MLB is triggered when the number of
synchronized UEs in the cell is greater than or equal
to the sum of the MlbMinUeNumThd and
MlbMinUeNumOffset parameter values and the
downlink PRB usage of the cell is greater than or
equal to the sum of the InterFreqMlbThd and
LoadOffset parameter values. MLB stops when the
downlink PRB usage of the cell or the number of
synchronized UEs falls below the InterFreqMlbThd
parameter value or the MlbMinUeNumThd parameter
value, respectively. For LTE TDD, the
InterFreqMlbThd parameter indicates the threshold of
the downlink PRB usage for triggering inter-frequency
MLB. This parameter applies only to LTE FDD and
LTE TDD.
GUI Value Range: 1~100
Unit: %
Actual Value Range: 1~100
Default Value: 60
InterFre FreqPriI ADD LBFD-0 Mobility Meaning: Indicates the RSRP threshold for frequency-
qHoGro nterFreq INTERF 02018/ Manage priority-based inter-frequency measurement event A1.
up HoA1Th REQHO TDLBF ment When the measured RSRP value exceeds this
dRsrp GROUP D-00201 threshold, an event A1 report will be sent. This
MOD 8 parameter applies only to LTE FDD and LTE TDD.
INTERF GUI Value Range: -140~-43
REQHO Unit: dBm
GROUP
Actual Value Range: -140~-43
LST
INTERF Default Value: -85
REQHO
GROUP
IntraRat FreqPriI MOD LBFD-0 Mobility Meaning: Indicates the triggering quantity for events
HoCom nterFreq INTRA 02018/ Manage A1 and A2 related to frequency-priority-based inter-
m HoA1Tr RATHO TDLBF ment frequency handovers. RSRP measurements slightly
igQuan COMM D-00201 vary with the load, and there is little signal fluctuation.
LST 8 By contrast, RSRQ measurements vary with the load
INTRA and are likely to reflect the signal quality of the cell in
RATHO real time. If this parameter is set to BOTH, both
COMM RSRP- and RSRQ-based measurement configurations
are delivered. When either the RSRP-based o RSRQ-
based entering condition of event A1 or A2 is met, the
UE reports event A1 or A2. For details, see 3GPP TS
36.331. This parameter applies only to LTE FDD and
LTE TDD.
GUI Value Range: RSRP, RSRQ, BOTH
Unit: None
Actual Value Range: RSRP, RSRQ, BOTH
Default Value: RSRP
IntraRat FreqPri MOD LBFD-0 Mobility Meaning: Indicates the period during which the
HoCom HoCand INTRA 02018/ Manage eNodeB selects candidate UEs in the cell to perform
m idateUe RATHO TDLBF ment frequency priority-based inter-frequency
SelPer COMM D-00201 measurement. If this parameter is set to 0, no
LST 8 candidate UEs in the cell is periodically selected. This
INTRA parameter applies only to LTE FDD and LTE TDD.
RATHO GUI Value Range: 0~500
COMM Unit: s
Actual Value Range: 0~500
Default Value: 0
EutranIn FreqPri ADD LBFD-0 Mobility Meaning: Indicates whether to enable or disable
terNFre BasedH EUTRA 02018/ Manage measurement for frequency-priority-based inter-
q oMeasFl NINTE TDLBF ment frequency handovers to neighboring frequencies. In
ag RNFRE D-00201 frequency-priority-based handovers, if the eNodeB
Q 8 delivers frequencies to be measured based on
MOD frequency configuration, the frequencies with the
EUTRA FreqPriBasedHoMeasFlag parameter set to ENABLE
NINTE can be measured, and the frequencies with the
RNFRE FreqPriBasedHoMeasFlag parameter set to DISABLE
Q cannot be measured. This parameter applies only to
LTE FDD and LTE TDD.
LST
EUTRA GUI Value Range: DISABLE(Disable),
NINTE ENABLE(Enable)
RNFRE Unit: None
Q Actual Value Range: DISABLE, ENABLE
Default Value: DISABLE(Disable)
GeranN Lac ADD LOFD-1 Separate Meaning: Indicates the location area code (LAC) of
etworkC GERAN 11204/ Mobility the GERAN cell. It uniquely identifies a location
apCfg NETW TDLOF Policies within a PLMN. A value in the range of 1-65533 and
ORKCA D-13121 to 65535 indicates a specific LAC on the network, and
PCFG 0 GERAN 4294967295 indicates all LACs under the PLMN.
LST for That is, the policy applies to all LACs under the
GERAN Multi PLMN. This parameter applies only to LTE FDD.
NETW PLMN GUI Value Range: 1~65533,65535,4294967295
ORKCA Unit: None
PCFG
Actual Value Range: 1~65533,65535,,4294967295
MOD
GERAN Default Value: None
NETW
ORKCA
PCFG
RMV
GERAN
NETW
ORKCA
PCFG
14 Counters
15 Glossary
16 Reference Documents