Sie sind auf Seite 1von 29

BASE PLATE DESIGN

1)CALCULATION OBJECTIVE/PURPOSE:

The puprose of this calculation is to design the base plate for following cases
i)Pinned base.
ii)Fixed about major and minor axis.

2)REFERENCES:

i)Engineering Specifications
ii)C/S/A Design criteria project anchor bolt design standard.
iii)Design of welded steel structures- Blodgett.
iv)Manual of steel construction -Allowable stress design (AISC-ASD).

3)BASIS/METHODOLOGY:

i) Pinned base
a)Calculate the base pressure in concrete support.
b)Find maximum moment at column flange edge.
c)Find thickness of base plate by using allowable bending stress.

In this case tensile load is shared by all bolts and design of base plate & anchor bolts is given in following pages.
ii)Fixed about major axis

f e

Pc

sc

Pc+ Pt

Pt Y

Figure-1

There are three equations and three unknowns Pt, Y and sc


1)
∑V=0

1/2 x Y x sc x B - Pt - Pc = 0

sc = 2 x (Pt + Pc) / (Y x B) …………. eq.1

2) ∑M=0

Pt x f + (Pc + Pt) x ( P/2 - Y/3) - Pc x e = 0

Pc = - Pt (D/2 - Y/3 + f)/ (D/2 - Y/3 - e) …………. eq.2


………….
3) Elastic behavior of concrete support and steel bolts

Pt / (As x sc x n) = (D/2 -Y +f) / Y …………. eq.3

where, e = Eccentricity (M/P)

As = Total area of steel hold-down


bolts under tension
B = Width of base plate
D = Length of base plate
sc = Stress in concrete support

Substituting value of eq. 3 and eq.2 in eq. 1, we get

Y3 + 3 x (e - D/2) x Y2 + 6 x n x As x (f + e) x Y / B - 6 x n x As x (D/2 + f) x (f + e) / B = 0

Reduce this eq.. to

Y3 + k1 x Y2 + k2 x Y + k3 = 0

where, k1 = 3 x (e - D/2)

k2 = 6 x n x As x (f + e) / B

k3 = - k2 x (D/2 + f)

Maximum bearing stress is found by followin equation

1 N
Pa+ M = σ c NB H−
2 3 ( )
(OR)
2 NP
σ c=
Es
N 2 B−2 A s
( )
Ec
( H −N )

Maximum moment is taken at column flange edge,and thickness of base plate is found using allowble stress
in bending for each load case.

Base plate thickness is calculated by considering the tensile load in bolt.


Tensile load in each bolt is calculated by following equation.
P = P/n + M/(n x 2xf)
2f - Lever arm
n = Number of bolts
Maximum moment is taken at column flange edge and thickness of base plate is found using allowable stress.

ANCHOR BOLTS:

1)Design of anchor bolts is based on IS 800:1984, class 4.6


2)Number of Anchor bolts are based on tensile load on column and it is assumed that shear is taken by shear lug.
3)Anchor bolts are of type 4.6
4)Projection of Anchor bolts = Grout thickness+Base plate thickness+ 1 Nut allowance.

SHEAR LUG:

1)Shear lug is provided for all the columns


3)Pocket (L) for shear lug = Length of shear lug+1(one) inch on each side.
4)Depth of pocket = Depth of shear lug(H)+2 inch.
LOAD
RX (KN) RY(KN) RZ (KN) RMX (KNM) RMY (KNM)
JOINT CASE

38 51 -31.347 487.005 -13.897 0 0


38 52 -40.412 74.682 3.182 0 0
38 53 -19.753 169.634 17.066 0 0
38 54 25.415 -20.391 -12.416 0 0
38 55 46.035 74.756 1.521 0 0
38 56 -18.896 -6.669 -13.548 0 0
38 57 1.737 98.442 4.145 0 0
38 58 -18.898 -24.94 -11.356 0 0
38 59 1.738 70.143 2.548 0 0
38 100 -55.683 372.1 -9.437 0 0
38 101 -39.157 448.061 1.67 0 0
38 102 -3.022 296.041 -21.916 0 0
38 103 13.474 372.16 -10.766 0 0
38 104 -38.471 307.019 -22.821 0 0
38 105 -21.964 391.108 -8.667 0 0
38 106 -38.473 292.403 -21.068 0 0
38 107 -21.964 368.469 -9.944 0 0
38 108 -28.713 343.369 -29.175 0 0
38 109 -28.738 448.219 10.693 0 0
38 110 -21.198 324.282 -32.924 0 0
38 111 -28.932 350.076 -29.179 0 0
38 112 -21.417 330.989 -32.928 0 0
38 113 -21.223 429.133 6.944 0 0
38 114 -28.957 454.926 10.689 0 0
38 115 -21.442 435.84 6.94 0 0
38 116 -37.49 402.334 -10.847 0 0
38 117 -12.439 338.712 -23.345 0 0
38 118 -37.497 433.79 1.113 0 0
38 119 -37.708 409.041 -10.851 0 0
38 120 -37.716 440.497 1.109 0 0
38 121 -12.447 370.167 -11.384 0 0
38 122 -12.658 345.418 -23.349 0 0
38 123 -12.666 376.874 -11.388 0 0
38 124 -28.467 372.242 -15.217 0 0
38 125 -29.196 394.598 -15.23 0 0
38 126 -28.474 403.697 -3.256 0 0
38 127 -20.952 353.155 -18.966 0 0
38 128 -20.959 384.61 -7.006 0 0
38 129 -29.204 426.053 -3.269 0 0
38 130 -21.681 375.511 -18.979 0 0
38 131 -21.689 406.966 -7.019 0 0
40 51 13.845 323.192 -12.141 0 0
40 52 -20.24 34.822 -1.243 0 0
40 53 -94.805 92.251 -14.828 0 0
40 54 77.607 86.985 14.052 0 0
40 55 3.01 146.122 0.445 0 0
40 56 65.106 66.762 13.353 0 0
LOAD
RX (KN) RY(KN) RZ (KN) RMX (KNM) RMY (KNM)
JOINT CASE
40 57 -9.451 128.343 2.477 0 0
40 58 65.102 63.259 8.821 0 0
40 59 -9.45 122.524 -4.736 0 0
40 100 -6.838 184.267 -11.414 0 0
40 101 -66.49 230.21 -22.282 0 0
40 102 71.44 225.997 0.822 0 0
40 103 11.762 273.307 -10.064 0 0
40 104 61.439 209.819 0.262 0 0
40 105 1.793 259.084 -8.438 0 0
40 106 61.436 207.016 -3.363 0 0
40 107 1.794 254.429 -14.209 0 0
40 108 7.157 239.286 -31.077 0 0
40 109 7.135 261.699 7.976 0 0
40 110 14.799 248.832 -27.391 0 0
40 111 7.376 245.861 -31.087 0 0
40 112 15.018 255.407 -27.402 0 0
40 113 14.777 271.245 11.662 0 0
40 114 7.354 268.275 7.965 0 0
40 115 14.996 277.821 11.651 0 0
40 116 -1.766 235.994 -21.708 0 0
40 117 23.707 267.814 -9.422 0 0
40 118 -1.773 242.718 -9.992 0 0
40 119 -1.547 242.569 -21.719 0 0
40 120 -1.554 249.293 -10.003 0 0
40 121 23.7 274.538 2.294 0 0
40 122 23.925 274.389 -9.433 0 0
40 123 23.919 281.113 2.283 0 0
40 124 6.894 239.459 -17.396 0 0
40 125 7.623 261.377 -17.432 0 0
40 126 6.888 246.183 -5.68 0 0
40 127 14.536 249.005 -13.71 0 0
40 128 14.529 255.729 -1.994 0 0
40 129 7.617 268.101 -5.716 0 0
40 130 15.265 270.923 -13.746 0 0
40 131 15.258 277.647 -2.03 0 0
LOAD
RX (KN) RY(KN) RZ (KN) RMX (KNM) RMY (KNM)
JOINT CASE
LOAD
RX (KN) RY(KN) RZ (KN) RMX (KNM) RMY (KNM)
JOINT CASE
LOAD
RX (KN) RY(KN) RZ (KN) RMX (KNM) RMY (KNM)
JOINT CASE
LOAD
RX (KN) RY(KN) RZ (KN) RMX (KNM) RMY (KNM)
JOINT CASE
LOAD
RX (KN) RY(KN) RZ (KN) RMX (KNM) RMY (KNM)
JOINT CASE
LOAD
RX (KN) RY(KN) RZ (KN) RMX (KNM) RMY (KNM)
JOINT CASE
shear
check in
RMZ (KNM)
bolt

-145.18 ok
-175.008 check
-141.929 ok
154.132 check
186.983 check
-33.091 check
-0.109 ok
-33.033 check
-0.013 ok
-249.232 ok
-222.768 ok
14.08 ok
40.361 ok
-135.698 ok
-109.313 ok
-135.652 ok
-109.236 ok
-136.398 ok
-136.812 ok
-94.577 ok
-137.296 ok
-95.475 ok
-94.991 ok
-137.71 ok
-95.89 ok
-185.334 ok
-45.931 ok
-185.458 ok
-186.232 ok
-186.356 ok
-46.056 ok
-46.829 ok
-46.954 ok
-135.495 ok
-138.489 ok
-135.619 ok
-93.674 ok
-93.799 ok
-138.613 ok
-96.668 ok
-96.792 ok
39.029 ok
-118.86 check
-335.146 check
284.096 check
67.609 ok
190.402 check
shear
check in
RMZ (KNM)
bolt
-25.891 ok
190.458 check
-25.793 ok
-70.932 ok
-243.962 check
251.432 check
78.242 ok
176.477 ok
3.443 ok
176.521 ok
3.521 ok
10.072 ok
9.666 ok
51.888 ok
10.964 ok
52.78 ok
51.483 ok
10.558 ok
52.374 ok
-38.855 ok
100.532 ok
-38.977 ok
-37.964 ok
-38.085 ok
100.41 ok
101.424 ok
101.302 ok
8.89 ok
11.862 ok
8.768 ok
50.706 ok
50.584 ok
11.741 ok
53.679 ok
53.557 ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
shear
check in
RMZ (KNM)
bolt
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
shear
check in
RMZ (KNM)
bolt
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
shear
check in
RMZ (KNM)
bolt
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
shear
check in
RMZ (KNM)
bolt
ok
shear
check in
RMZ (KNM)
bolt
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
shear
check in
RMZ (KNM)
bolt
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
ok
BASE PLATE DESIGN

photo is for representative purposes only

BASE PLATE FOR SUPPORT NO: 38


Column designation BH540X270X12X20
Depth of column, D = 540 mm
Width of flange, B = 270 mm
Thickness of web,tw = 12 mm
Thickness of flange,Tf = 20 mm
Compressive strength of concrete (f'c) = 25 N/mm2
Yield strength of steel column = 250 N/mm2
Distance from C.L of Z-Dir bolts line to edge of base pl along x-dir (dtx) = 100 mm
Distance from C.L of X-Dir bolts line to edge of base pl along z-dir (dtz) = 100 mm
Elastic modulus of concrete = 25000 N/mm2
Elastic modulus of steel = 200000 N/mm2
Modular ratio of elasticity of steel to concrete(n) = 8.00 0.86451613
Concrete pedestal Length in x-dir,Bc = 950 mm
Concrete pedestal width in z-dir,Nc = 1140 mm
Allowable bearing stress on concrete = 7.75 N/mm2 SAFE
Yield strength of base plate = 250 N/mm2
Allowable bending stress in base plate = 165 N/mm2
Bolt dia = 42 mm
Total number of bolts = 8
Number of bolts to take tension due to Mx = 2
Number of bolts to take tension due to Mz = 4
Total cross sectional area of bolts to take tension due to Mx,atx = 2078 mm2 Max. bearing stress 6.7 131.0

Total cross sectional area of bolts to take tension due to Mz,atz = 4156 mm2
FINDING OF Yx: FINDING OF Yz:
Eccentricity Eccentricity Base plate Base plate Xnx (Length of Actual Bearing Xnz (Length of Actual Bearing Comined Cσc = Cσcx Combined tension,
LOAD Moment about x- Moment about z- B/6 + dtx/3 Location of Eccentricity in x- N/6 + dtz/3 Location of Eccentricity K2 =(( 6n x atz)/N) Tension in bolt K2 x Xnz =( 6n - atx/B) x Tension in bolt
LOAD CASE (ex) (ez) length in x- width in z- B/6 (mm) N/6 (mm) K1x= 3(ex-B/2) K3x = K2(B-dtx) pressure stress ,cσcx K1z= 3(ez-N/2) K3x = K2(N-dtz) pressure stress ,cσcz + Cσcz -Ry/(B.N) T/per = Zx/Nx + Assumed Actual
(kN) axis,MX (kNm) axis,MZ (kNm) (mm) dir (mm) in Z- dir x (ex +B/2 -dtx) due to Mz (KN) (ez +N/2 -dtz) due to Mx (KN) (N/mm2) Zz/Nz (kN) Assumed value Actual value
(mm) (mm) dir, B (mm) dir, N (mm) diagram) (mm) (N/mm2) diagram) (mm) (N/mm2) Equation value Equation value
(mm) (mm)
(mm) (mm)

SUPPORT - 38&40
51 487.005 0 -145.18 298.1 0.0 750 940 125.0 158.3 ex > B/6 + dtx/3 156.7 190.00 ez < N/6 -230.70 121624.01 79055606.5 407.81 2.83 55.93 0.00 0.00 0.00 #DIV/0! 0.69 0.00 2.829 14.0 407.812619585087 -6.33E-05 407.813 0.090356 0.00073768 0.090356
52 74.682 0 -175.008 2343.4 0.0 750 940 125.0 158.3 ex > B/6 + dtx/3 156.7 190.00 ez < N/6 5905.20 555680.19 361192123.5 201.92 3.54 260.91 0.00 0.00 0.00 #DIV/0! 0.11 0.00 3.544 65.2 201.917256727573 1.669E-06 201.917 0.090468 0.00074043 0.090468
53 169.634 0 -141.929 836.7 0.0 750 940 125.0 158.3 ex > B/6 + dtx/3 156.7 190.00 ez < N/6 1385.10 235926.39 153352153.5 242.89 2.90 161.77 0.00 0.00 0.00 #DIV/0! 0.24 0.00 2.899 40.4 242.893521698186 2.503E-06 242.894 0.09058 0.00074319 0.09058
54 -20.391 0 154.132 7558.8 0.0 750 940 125.0 158.3 |ex| => B/2-dtx 156.7 190.00 |ez| =< N/2-dtz 21551.40 1662499.04 1080624376.0 187.97 2.78 251.58 0.00 0.00 0.00 0.00 0.00 0.00 2.780 101.5 187.97135136191 -5.96E-06 187.971 0.090692 0.00074595 0.090692
55 74.756 0 186.983 2501.2 0.0 750 940 125.0 158.3 ex > B/6 + dtx/3 156.7 190.00 ez < N/6 6378.60 589168.71 382959661.5 200.61 3.77 281.15 0.00 0.00 0.00 #DIV/0! 0.11 0.00 3.774 70.3 200.607048494098 0 200.607 0.090805 0.00074873 0.090805
56 -6.669 0 -33.091 4961.9 0.0 750 940 125.0 158.3 |ex| => B/2-dtx 156.7 190.00 |ez| =< N/2-dtz 13760.70 1111381.60 722398040.0 191.18 0.57 52.90 0.00 0.00 0.00 0.00 0.00 0.00 0.570 21.7 191.177807668607 0 191.178 0.090917 0.0007515 0.090917
57 98.442 0 -0.109 1.1 0.0 750 940 125.0 158.3 ex < B/6 156.7 190.00 ez < N/6 0.00 0.00 0.0 42988.64 0.14 0.00 0.00 0.00 0.00 #DIV/0! 0.14 0.00 0.140 0.0 0.083306154548313 0.000578 0.083 0.091029 0.00075429 0.091029
58 -24.94 0 -33.033 1324.5 0.0 750 940 125.0 158.3 |ex| => B/2-dtx 156.7 190.00 |ez| =< N/2-dtz 2848.50 339447.93 220641154.5 218.53 0.36 44.18 0.00 0.00 0.00 0.00 0.00 0.00 0.360 20.5 218.526801362679 -1.88E-06 218.527 0.091141 0.00075708 0.091141
59 70.143 0 -0.013 0.2 0.0 750 940 125.0 158.3 ex < B/6 156.7 190.00 ez < N/6 0.00 0.00 0.0 234750.00 0.10 0.00 0.00 0.00 0.00 #DIV/0! 0.10 0.00 0.101 0.0 0.077517388827733 0.000466 0.078 0.091253 0.00075988 0.091253
100 372.1 0 -249.232 669.8 0.0 750 940 125.0 158.3 ex > B/6 + dtx/3 156.7 190.00 ez < N/6 884.40 200506.66 130329329.0 260.97 5.09 252.33 0.00 0.00 0.00 #DIV/0! 0.53 0.00 5.092 63.1 260.966874076014 5.96E-07 260.967 0.091365 0.00076268 0.091365
101 448.061 0 -222.768 497.2 0.0 750 940 125.0 158.3 ex > B/6 + dtx/3 156.7 190.00 ez < N/6 366.60 163877.27 106520225.5 295.94 4.51 179.47 0.00 0.00 0.00 #DIV/0! 0.64 0.00 4.514 44.9 295.935047530521 1.967E-06 295.935 0.091477 0.00076549 0.091477
102 296.041 0 14.08 47.6 0.0 750 940 125.0 158.3 ex < B/6 156.7 190.00 ez < N/6 0.00 0.00 0.0 1359.77 0.58 0.00 0.00 0.00 0.00 #DIV/0! 0.42 0.00 0.580 0.0 0.099064217438044 0.000972 0.099 0.091589 0.00076831 0.091589
103 372.16 0 40.361 108.5 0.0 750 940 125.0 158.3 ex < B/6 156.7 190.00 ez < N/6 0.00 0.00 0.0 807.03 0.99 0.00 0.00 0.00 0.00 #DIV/0! 0.53 0.00 0.992 0.0 0.07561780539954 0.000432 0.076 0.091702 0.00077114 0.091702
104 307.019 0 -135.698 442.0 0.0 750 940 125.0 158.3 ex > B/6 + dtx/3 156.7 190.00 ez < N/6 201.00 152162.66 98905729.0 314.61 2.73 96.80 0.00 0.00 0.00 #DIV/0! 0.44 0.00 2.735 24.2 314.608330774701 -5.81E-06 314.608 0.091814 0.00077397 0.091814
105 391.108 0 -109.313 279.5 0.0 750 940 125.0 158.3 ex > B/6 + dtx/3 156.7 190.00 ez < N/6 -286.50 117676.70 76489855.0 428.48 2.12 36.50 0.00 0.00 0.00 #DIV/0! 0.55 0.00 2.115 9.1 428.48214876429 5.066E-07 428.482 0.091926 0.00077681 0.091926
106 292.403 0 -135.652 463.9 0.0 750 940 125.0 158.3 ex > B/6 + dtx/3 156.7 190.00 ez < N/6 266.70 156810.30 101926695.0 306.53 2.74 101.99 0.00 0.00 0.00 #DIV/0! 0.41 0.00 2.735 25.5 306.52763457355 -4.53E-06 306.528 0.092038 0.00077965 0.092038
107 368.469 0 -109.236 296.5 0.0 750 940 125.0 158.3 ex > B/6 + dtx/3 156.7 190.00 ez < N/6 -235.50 121284.46 78834899.0 409.48 2.13 41.61 0.00 0.00 0.00 #DIV/0! 0.52 0.00 2.127 10.4 409.478698188892 0 409.479 0.09215 0.00078251 0.09215
108 343.369 0 -136.398 397.2 0.0 750 940 125.0 158.3 ex > B/6 + dtx/3 156.7 190.00 ez < N/6 66.60 142655.14 92725841.0 334.75 2.72 85.32 0.00 0.00 0.00 #DIV/0! 0.49 0.00 2.723 21.3 334.745663406878 0 334.746 0.092262 0.00078537 0.092262
109 448.219 0 -136.812 305.2 0.0 750 940 125.0 158.3 ex > B/6 + dtx/3 156.7 190.00 ez < N/6 -209.40 123130.78 80035007.0 400.66 2.67 55.33 0.00 0.00 0.00 #DIV/0! 0.64 0.00 2.674 13.8 400.657162142815 0 400.657 0.092374 0.00078824 0.092374
110 324.282 0 -94.577 291.7 0.0 750 940 125.0 158.3 ex > B/6 + dtx/3 156.7 190.00 ez < N/6 -249.90 120265.80 78172770.0 414.60 1.84 34.79 0.00 0.00 0.00 #DIV/0! 0.46 0.00 1.840 8.7 414.599453891075 0 414.599 0.092487 0.00079111 0.092487
111 350.076 0 -137.296 392.2 0.0 750 940 125.0 158.3 ex > B/6 + dtx/3 156.7 190.00 ez < N/6 51.60 141594.04 92036126.0 337.36 2.74 84.44 0.00 0.00 0.00 #DIV/0! 0.50 0.00 2.743 21.1 337.359487803597 -4.47E-07 337.359 0.092599 0.00079399 0.092599
112 330.989 0 -95.475 288.5 0.0 750 940 125.0 158.3 ex > B/6 + dtx/3 156.7 190.00 ez < N/6 -259.50 119586.69 77731348.5 418.12 1.86 34.27 0.00 0.00 0.00 #DIV/0! 0.47 0.00 1.861 8.6 418.117952842957 4.172E-07 418.118 0.092711 0.00079688 0.092711
113 429.133 0 -94.991 221.4 0.0 750 940 125.0 158.3 ex > B/6 + dtx/3 156.7 190.00 ez < N/6 -460.80 105346.64 68475316.0 514.64 1.84 16.10 0.00 0.00 0.00 #DIV/0! 0.61 0.00 1.841 4.0 514.639915616065 2.831E-07 514.640 0.092823 0.00079977 0.092823
114 454.926 0 -137.71 302.7 0.0 750 940 125.0 158.3 ex > B/6 + dtx/3 156.7 190.00 ez < N/6 -216.90 122600.23 79690149.5 403.13 2.69 54.77 0.00 0.00 0.00 #DIV/0! 0.65 0.00 2.695 13.7 403.133157564295 4.619E-07 403.133 0.092935 0.00080268 0.092935
115 435.84 0 -95.89 220.0 0.0 750 940 125.0 158.3 ex > B/6 + dtx/3 156.7 190.00 ez < N/6 -465.00 105049.53 68282194.5 517.17 1.86 15.87 0.00 0.00 0.00 #DIV/0! 0.62 0.00 1.862 4.0 517.170211007346 0 517.170 0.093047 0.00080558 0.093047
116 402.334 0 -185.334 460.6 0.0 750 940 125.0 158.3 ex > B/6 + dtx/3 156.7 190.00 ez < N/6 256.80 156109.97 101471480.5 307.68 3.74 138.29 0.00 0.00 0.00 #DIV/0! 0.57 0.00 3.739 34.6 307.683254602362 2.18E-05 307.683 0.093159 0.0008085 0.093159
117 338.712 0 -45.931 135.6 0.0 750 940 125.0 158.3 B/6 < ex < B/6 + dtx/3 156.7 190.00 ez < N/6 0.00 0.00 0.0 718.20 1.00 0.00 0.00 0.00 0.00 #DIV/0! 0.48 0.00 1.000 0.0 0.083373920333346 0.00058 0.083 0.093272 0.00081142 0.093272
118 433.79 0 -185.458 427.5 0.0 750 940 125.0 158.3 ex > B/6 + dtx/3 156.7 190.00 ez < N/6 157.50 149085.45 96905542.5 320.54 3.72 127.26 0.00 0.00 0.00 #DIV/0! 0.62 0.00 3.725 31.8 320.541874163182 1.565E-06 320.542 0.093384 0.00081435 0.093384
119 409.041 0 -186.232 455.3 0.0 750 940 125.0 158.3 ex > B/6 + dtx/3 156.7 190.00 ez < N/6 240.90 154985.20 100740380.0 309.58 3.75 137.26 0.00 0.00 0.00 #DIV/0! 0.58 0.00 3.750 34.3 309.583687345437 1.498E-05 309.584 0.093496 0.00081729 0.093496
120 440.497 0 -186.356 423.1 0.0 750 940 125.0 158.3 ex > B/6 + dtx/3 156.7 190.00 ez < N/6 144.30 148151.67 96298585.5 322.45 3.74 126.33 0.00 0.00 0.00 #DIV/0! 0.62 0.00 3.735 31.6 322.444962897076 0 322.445 0.093608 0.00082024 0.093608
121 370.167 0 -46.056 124.4 0.0 750 940 125.0 158.3 ex < B/6 156.7 190.00 ez < N/6 0.00 0.00 0.0 751.81 1.05 0.00 0.00 0.00 0.00 #DIV/0! 0.53 0.00 1.055 0.0 0.083901182322555 0.000591 0.084 0.09372 0.00082319 0.09372
122 345.418 0 -46.829 135.6 0.0 750 940 125.0 158.3 B/6 < ex < B/6 + dtx/3 156.7 190.00 ez < N/6 0.00 0.00 0.0 718.20 1.02 0.00 0.00 0.00 0.00 #DIV/0! 0.49 0.00 1.020 0.0 0.083442175379031 0.000581 0.083 0.093832 0.00082615 0.093832
123 376.874 0 -46.954 124.6 0.0 750 940 125.0 158.3 ex < B/6 156.7 190.00 ez < N/6 0.00 0.00 0.0 751.20 1.07 0.00 0.00 0.00 0.00 #DIV/0! 0.53 0.00 1.065 0.0 0.083970632201078 0.000592 0.084 0.077186 0.00045986 0.077186
124 372.242 0 -135.495 364.0 0.0 750 940 125.0 158.3 ex > B/6 + dtx/3 156.7 190.00 ez < N/6 -33.00 135609.40 88146110.0 353.82 2.69 74.82 0.00 0.00 0.00 #DIV/0! 0.53 0.00 2.692 18.7 353.823664985485 6.318E-06 353.824 0.093717 0.00082309 0.093717
125 394.598 0 -138.489 351.0 0.0 750 940 125.0 158.3 ex > B/6 + dtx/3 156.7 190.00 ez < N/6 -72.00 132850.52 86352838.0 362.54 2.74 72.22 0.00 0.00 0.00 #DIV/0! 0.56 0.00 2.740 18.1 362.544237201645 9.835E-07 362.544 0.079099 0.00049489 0.079099
126 403.697 0 -135.619 335.9 0.0 750 940 125.0 158.3 ex > B/6 + dtx/3 156.7 190.00 ez < N/6 -117.30 129645.98 84269887.0 373.73 2.67 65.67 0.00 0.00 0.00 #DIV/0! 0.57 0.00 2.667 16.4 373.73143629964 0 373.731 0.07912 0.00049529 0.07912
127 353.155 0 -93.674 265.2 0.0 750 940 125.0 158.3 ex > B/6 + dtx/3 156.7 190.00 ez < N/6 -329.40 114641.93 74517254.5 446.46 1.81 27.50 0.00 0.00 0.00 #DIV/0! 0.50 0.00 1.809 6.9 446.462520077953 -1.45E-06 446.463 0.089439 0.00071544 0.089439
128 384.61 0 -93.799 243.9 0.0 750 940 125.0 158.3 ex > B/6 + dtx/3 156.7 190.00 ez < N/6 -393.30 110121.62 71579053.0 477.02 1.81 21.86 0.00 0.00 0.00 #DIV/0! 0.55 0.00 1.814 5.5 477.016437539431 -3.58E-07 477.016 0.096527 0.0008994 0.096527
129 426.053 0 -138.613 325.3 0.0 750 940 125.0 158.3 ex > B/6 + dtx/3 156.7 190.00 ez < N/6 -149.10 127396.43 82807679.5 382.35 2.72 63.39 0.00 0.00 0.00 #DIV/0! 0.60 0.00 2.716 15.8 382.346640932217 0 382.347 0.094617 0.00084705 0.094617
130 375.511 0 -96.668 257.4 0.0 750 940 125.0 158.3 ex > B/6 + dtx/3 156.7 190.00 ez < N/6 -352.80 112986.61 73441296.5 457.11 1.87 26.24 0.00 0.00 0.00 #DIV/0! 0.53 0.00 1.867 6.6 457.106308181386 0.000347 457.106 0.094729 0.00085007 0.094729
131 406.966 0 -96.792 237.8 0.0 750 940 125.0 158.3 ex > B/6 + dtx/3 156.7 190.00 ez < N/6 -411.60 108827.07 70737595.5 486.66 1.87 20.87 0.00 0.00 0.00 #DIV/0! 0.58 0.00 1.873 5.2 486.657030627626 -2.08E-05 486.657 0.087021 0.00065897 0.087021
51 323.192 0 39.029 120.8 0.0 750 940 125.0 158.3 ex < B/6 156.7 190.00 ez < N/6 0.00 0.00 0.0 763.04 0.90 0.00 0.00 0.00 0.00 #DIV/0! 0.46 0.00 0.902 0.0 0.093938271723943 0.000829 0.094 0.099618 0.00098858 0.099618
52 34.822 0 -118.86 3413.4 0.0 750 940 125.0 158.3 ex > B/6 + dtx/3 156.7 190.00 ez < N/6 9115.20 782756.96 508792024.0 195.48 2.39 184.79 0.00 0.00 0.00 #DIV/0! 0.05 0.00 2.391 46.2 195.478875151792 -4.61E-05 195.479 0.095066 0.00085916 0.095066
53 92.251 0 -335.146 3633.0 0.0 750 940 125.0 158.3 ex > B/6 + dtx/3 156.7 190.00 ez < N/6 9774.00 829360.75 539084487.5 194.64 6.74 523.89 0.00 0.00 0.00 #DIV/0! 0.13 0.00 6.739 131.0 194.63967990464 0 194.640 0.095178 0.0008622 0.095178
54 86.985 0 284.096 3266.0 0.0 750 940 125.0 158.3 ex > B/6 + dtx/3 156.7 190.00 ez < N/6 8673.00 751475.54 488459101.0 196.11 5.72 439.87 0.00 0.00 0.00 #DIV/0! 0.12 0.00 5.717 110.0 196.107413585199 6.258E-05 196.107 0.07842 0.00048227 0.07842
55 146.122 0 67.609 462.7 0.0 750 940 125.0 158.3 ex > B/6 + dtx/3 156.7 190.00 ez < N/6 263.10 156555.64 101761166.0 306.95 1.36 50.70 0.00 0.00 0.00 #DIV/0! 0.21 0.00 1.363 12.7 306.945453742496 6.546E-05 306.945 0.07609 0.00044053 0.07609
56 66.762 0 190.402 2852.0 0.0 750 940 125.0 158.3 ex > B/6 + dtx/3 156.7 190.00 ez < N/6 7431.00 663615.93 431350354.5 198.23 3.84 290.76 0.00 0.00 0.00 #DIV/0! 0.09 0.00 3.835 72.7 198.23272611704 6.413E-05 198.233 0.095289 0.00086523 0.095289
57 128.343 0 -25.891 201.7 0.0 750 940 125.0 158.3 ex > B/6 + dtx/3 156.7 190.00 ez < N/6 -519.90 101165.88 65757822.0 552.30 0.51 2.98 0.00 0.00 0.00 #DIV/0! 0.18 0.00 0.508 0.7 552.301726455912 0 552.302 0.078404 0.00048197 0.078404
58 63.259 0 190.458 3010.8 0.0 750 940 125.0 158.3 ex > B/6 + dtx/3 156.7 190.00 ez < N/6 7907.40 697316.67 453255835.5 197.35 3.84 292.53 0.00 0.00 0.00 #DIV/0! 0.09 0.00 3.840 73.1 197.346063724975 6.211E-05 197.346 0.09973 0.00099191 0.09973
59 122.524 0 -25.793 210.5 0.0 750 940 125.0 158.3 ex > B/6 + dtx/3 156.7 190.00 ez < N/6 -493.50 103033.43 66971729.5 534.93 0.50 3.59 0.00 0.00 0.00 #DIV/0! 0.17 0.00 0.496 0.9 534.93197906398 3.129E-07 534.932 0.080353 0.0005188 0.080353
100 184.267 0 -70.932 384.9 0.0 750 940 125.0 158.3 ex > B/6 + dtx/3 156.7 190.00 ez < N/6 29.70 140044.82 91029133.0 341.33 1.41 42.50 0.00 0.00 0.00 #DIV/0! 0.26 0.00 1.409 10.6 341.330687947363 -5.36E-07 341.331 0.089904 0.00072667 0.089904
101 230.21 0 -243.962 1059.7 0.0 750 940 125.0 158.3 ex > B/6 + dtx/3 156.7 190.00 ez < N/6 2054.10 283251.74 184113631.0 228.65 4.98 305.29 0.00 0.00 0.00 #DIV/0! 0.33 0.00 4.983 76.3 228.652952705829 -1.74E-05 228.653 0.096075 0.00088681 0.096075
102 225.997 0 251.432 1112.5 0.0 750 940 125.0 158.3 ex > B/6 + dtx/3 156.7 190.00 ez < N/6 2212.50 294457.02 191397063.0 226.21 5.13 319.73 0.00 0.00 0.00 #DIV/0! 0.32 0.00 5.129 79.9 226.207790558383 4.435E-05 226.208 0.092684 0.00079619 0.092684
103 273.307 0 78.242 286.3 0.0 750 940 125.0 158.3 ex > B/6 + dtx/3 156.7 190.00 ez < N/6 -266.10 119119.80 77427870.0 420.59 1.52 27.61 0.00 0.00 0.00 #DIV/0! 0.39 0.00 1.522 6.9 420.586756306839 -0.000384 420.587 0.096299 0.00089304 0.096299
104 209.819 0 176.477 841.1 0.0 750 940 125.0 158.3 ex > B/6 + dtx/3 156.7 190.00 ez < N/6 1398.30 236860.17 153959110.5 242.53 3.61 201.63 0.00 0.00 0.00 #DIV/0! 0.30 0.00 3.612 50.4 242.528606357575 3.126E-05 242.529 0.096411 0.00089616 0.096411
105 259.084 0 3.443 13.3 0.0 750 940 125.0 158.3 ex < B/6 156.7 190.00 ez < N/6 0.00 0.00 0.0 3899.44 0.41 0.00 0.00 0.00 0.00 #DIV/0! 0.37 0.00 0.413 0.0 0.09440690150148 0.000841 0.094 0.096524 0.00089929 0.096524
106 207.016 0 176.521 852.7 0.0 750 940 125.0 158.3 ex > B/6 + dtx/3 156.7 190.00 ez < N/6 1433.10 239321.93 155559254.5 241.59 3.61 202.93 0.00 0.00 0.00 #DIV/0! 0.29 0.00 3.606 50.7 241.587260932125 3.424E-05 241.587 0.096636 0.00090243 0.096636
107 254.429 0 3.521 13.8 0.0 750 940 125.0 158.3 ex < B/6 156.7 190.00 ez < N/6 0.00 0.00 0.0 3771.74 0.40 0.00 0.00 0.00 0.00 #DIV/0! 0.36 0.00 0.399 0.0 0.091150697492688 0.000757 0.091 0.096748 0.00090557 0.096748
108 239.286 0 10.072 42.1 0.0 750 940 125.0 158.3 ex < B/6 156.7 190.00 ez < N/6 0.00 0.00 0.0 1488.42 0.45 0.00 0.00 0.00 0.00 #DIV/0! 0.34 0.00 0.451 0.0 0.095546902647883 0.000872 0.096 0.09686 0.00090873 0.09686
109 261.699 0 9.666 36.9 0.0 750 940 125.0 158.3 ex < B/6 156.7 190.00 ez < N/6 0.00 0.00 0.0 1645.33 0.48 0.00 0.00 0.00 0.00 #DIV/0! 0.37 0.00 0.479 0.0 0.097159577748903 0.000917 0.097 0.096972 0.00091189 0.096972
110 248.832 0 51.888 208.5 0.0 750 940 125.0 158.3 ex > B/6 + dtx/3 156.7 190.00 ez < N/6 -499.50 102608.99 66695843.5 538.80 1.01 6.93 0.00 0.00 0.00 #DIV/0! 0.35 0.00 1.007 1.7 538.802563704733 0 538.803 0.097084 0.00091505 0.097084
111 245.861 0 10.964 44.6 0.0 750 940 125.0 158.3 ex < B/6 156.7 190.00 ez < N/6 0.00 0.00 0.0 1426.01 0.47 0.00 0.00 0.00 0.00 #DIV/0! 0.35 0.00 0.471 0.0 0.095622770230782 0.000874 0.096 0.097196 0.00091823 0.097196
112 255.407 0 52.78 206.7 0.0 750 940 125.0 158.3 ex > B/6 + dtx/3 156.7 190.00 ez < N/6 -504.90 102226.99 66447543.5 542.33 1.03 6.79 0.00 0.00 0.00 #DIV/0! 0.36 0.00 1.028 1.7 542.324964909615 -2.61E-07 542.325 0.082434 0.00056017 0.082434
113 271.245 0 51.483 189.8 0.0 750 940 125.0 158.3 ex > B/6 + dtx/3 156.7 190.00 ez < N/6 -555.60 98640.45 64116292.5 577.17 1.02 4.26 0.00 0.00 0.00 #DIV/0! 0.38 0.00 1.015 1.1 577.166656638058 -3.87E-06 577.167 0.097421 0.0009246 0.097421
114 268.275 0 10.558 39.4 0.0 750 940 125.0 158.3 ex < B/6 156.7 190.00 ez < N/6 0.00 0.00 0.0 1564.72 0.50 0.00 0.00 0.00 0.00 #DIV/0! 0.38 0.00 0.499 0.0 0.097237388095111 0.000919 0.097 0.097533 0.0009278 0.097533
115 277.821 0 52.374 188.5 0.0 750 940 125.0 158.3 ex > B/6 + dtx/3 156.7 190.00 ez < N/6 -559.50 98364.56 63936964.0 579.98 1.03 4.15 0.00 0.00 0.00 #DIV/0! 0.39 0.00 1.026 1.0 579.976705774121 -4.81E-06 579.977 0.097645 0.000931 0.097645
116 235.994 0 -38.855 164.6 0.0 750 940 125.0 158.3 ex > B/6 + dtx/3 156.7 190.00 ez < N/6 -631.20 93292.47 60640105.5 634.74 0.79 0.64 0.00 0.00 0.00 #DIV/0! 0.33 0.00 0.785 0.2 634.734797541718 -3.28E-07 634.735 0.097757 0.00093421 0.097757
117 267.814 0 100.532 375.4 0.0 750 940 125.0 158.3 ex > B/6 + dtx/3 156.7 190.00 ez < N/6 1.20 138028.72 89718668.0 346.79 2.00 58.13 0.00 0.00 0.00 #DIV/0! 0.38 0.00 2.000 14.5 346.792523743548 -4.02E-07 346.793 0.097869 0.00093743 0.097869
118 242.718 0 -38.977 160.6 0.0 750 940 125.0 158.3 ex > B/6 + dtx/3 156.7 190.00 ez < N/6 -643.20 92443.59 60088333.5 644.44 0.80 0.23 0.00 0.00 0.00 #DIV/0! 0.34 0.00 0.796 0.1 644.438057784282 1.963E-05 644.438 0.097981 0.00094065 0.097981
119 242.569 0 -37.964 156.5 0.0 750 940 125.0 158.3 B/6 < ex < B/6 + dtx/3 156.7 190.00 ez < N/6 0.00 0.00 0.0 655.50 0.79 0.00 0.00 0.00 0.00 #DIV/0! 0.34 0.00 0.786 0.0 0.077241127368539 0.000461 0.077 0.098093 0.00094389 0.098093
120 249.293 0 -38.085 152.8 0.0 750 940 125.0 158.3 B/6 < ex < B/6 + dtx/3 156.7 190.00 ez < N/6 0.00 0.00 0.0 666.60 0.80 0.00 0.00 0.00 0.00 #DIV/0! 0.35 0.00 0.796 0.0 0.077620692975521 0.000468 0.078 0.092465 0.00079055 0.092465
121 274.538 0 100.41 365.7 0.0 750 940 125.0 158.3 ex > B/6 + dtx/3 156.7 190.00 ez < N/6 -27.90 135970.17 88380610.5 352.74 1.99 55.83 0.00 0.00 0.00 #DIV/0! 0.39 0.00 1.991 14.0 352.740226416582 -7.45E-07 352.740 0.089071 0.00070665 0.089071
122 274.389 0 101.424 369.6 0.0 750 940 125.0 158.3 ex > B/6 + dtx/3 156.7 190.00 ez < N/6 -16.20 136797.83 88918589.5 350.30 2.01 57.31 0.00 0.00 0.00 #DIV/0! 0.39 0.00 2.011 14.3 350.301759758592 -7.3E-07 350.302 0.096163 0.00088925 0.096163
123 281.113 0 101.302 360.4 0.0 750 940 125.0 158.3 ex > B/6 + dtx/3 156.7 190.00 ez < N/6 -43.80 134845.40 87649510.0 356.16 2.01 55.09 0.00 0.00 0.00 #DIV/0! 0.40 0.00 2.011 13.8 356.160254707624 -1.4E-06 356.160 0.088388 0.00069052 0.088388
124 239.459 0 8.89 37.1 0.0 750 940 125.0 158.3 ex < B/6 156.7 190.00 ez < N/6 0.00 0.00 0.0 1638.48 0.44 0.00 0.00 0.00 0.00 #DIV/0! 0.34 0.00 0.440 0.0 0.096003499807321 0.000885 0.096 0.096401 0.00089587 0.096401
125 261.377 0 11.862 45.4 0.0 750 940 125.0 158.3 ex < B/6 156.7 190.00 ez < N/6 0.00 0.00 0.0 1407.49 0.51 0.00 0.00 0.00 0.00 #DIV/0! 0.37 0.00 0.509 0.0 0.096271390027293 0.000892 0.096 0.07958 0.00050398 0.07958
FINDING OF Yx: FINDING OF Yz:
Eccentricity Eccentricity Base plate Base plate Xnx (Length of Actual Bearing Xnz (Length of Actual Bearing Comined Cσc = Cσcx Combined tension,
LOAD Moment about x- Moment about z- B/6 + dtx/3 Location of Eccentricity in x- N/6 + dtz/3 Location of Eccentricity K2 =(( 6n x atz)/N) Tension in bolt K2 x Xnz =( 6n - atx/B) x Tension in bolt
LOAD CASE (ex) (ez) length in x- width in z- B/6 (mm) N/6 (mm) K1x= 3(ex-B/2) K3x = K2(B-dtx) pressure stress ,cσcx K1z= 3(ez-N/2) K3x = K2(N-dtz) pressure stress ,cσcz + Cσcz -Ry/(B.N) T/per = Zx/Nx + Assumed Actual
(kN) axis,MX (kNm) axis,MZ (kNm) (mm) dir (mm) in Z- dir x (ex +B/2 -dtx) due to Mz (KN) (ez +N/2 -dtz) due to Mx (KN) (N/mm2) Zz/Nz (kN) Assumed value Actual value
(mm) (mm) dir, B (mm) dir, N (mm) diagram) (mm) (N/mm2) diagram) (mm) (N/mm2) Equation value Equation value
(mm) (mm)
(mm) (mm)
126 246.183 0 8.768 35.6 0.0 750 940 125.0 158.3 ex < B/6 156.7 190.00 ez < N/6 0.00 0.00 0.0 1691.71 0.45 0.00 0.00 0.00 0.00 #DIV/0! 0.35 0.00 0.451 0.0 0.096501913327608 0.000899 0.097 0.098987 0.0009699 0.098987
127 249.005 0 50.706 203.6 0.0 750 940 125.0 158.3 ex > B/6 + dtx/3 156.7 190.00 ez < N/6 -514.20 101569.10 66019915.0 548.48 0.99 6.09 0.00 0.00 0.00 #DIV/0! 0.35 0.00 0.987 1.5 548.477345436383 -4.84E-07 548.477 0.083551 0.00058324 0.083551
128 255.729 0 50.584 197.8 0.0 750 940 125.0 158.3 ex > B/6 + dtx/3 156.7 190.00 ez < N/6 -531.60 100338.22 65219843.0 560.28 0.99 5.28 0.00 0.00 0.00 #DIV/0! 0.36 0.00 0.987 1.3 560.278433653031 -1.41E-06 560.278 0.099103 0.00097332 0.099103
129 268.101 0 11.741 43.8 0.0 750 940 125.0 158.3 ex < B/6 156.7 190.00 ez < N/6 0.00 0.00 0.0 1445.21 0.51 0.00 0.00 0.00 0.00 #DIV/0! 0.38 0.00 0.510 0.0 0.096771908448365 0.000906 0.097 0.099215 0.00097663 0.099215
130 270.923 0 53.679 198.1 0.0 750 940 125.0 158.3 ex > B/6 + dtx/3 156.7 190.00 ez < N/6 -530.70 100401.89 65261228.5 559.66 1.05 5.64 0.00 0.00 0.00 #DIV/0! 0.38 0.00 1.046 1.4 559.658823776719 -1.14E-06 559.659 0.099327 0.00097995 0.099327
131 277.647 0 53.557 192.9 0.0 750 940 125.0 158.3 ex > B/6 + dtx/3 156.7 190.00 ez < N/6 -546.30 99298.34 64543921.0 570.54 1.05 4.88 0.00 0.00 0.00 #DIV/0! 0.39 0.00 1.046 1.2 570.539427334251 -2.13E-06 570.539 0.097411 0.00092433 0.097411
Base Plate thickness calculation:

l2

l1

picture is for representative purpose only


Checking pressure in panel 1 :
(Three edges continuous,one edge free)

Length of panel (a) = 200 mm


Width of panel(b) = 200 mm
Ratio (a/b) = 1.00
Refer Roark's table for stress coefficient :
from Roark's table :
fb= βx qxb2/t2
β1(Refer roarks(tables)sheet = 0.265 These are taken from
β2(Refer roarks(tables)sheet = 0.230 roarks(tables)sheet
β3(Refer roarks(tables)sheet = 0.446
Allowable bending stress = 165 N/mm2
Length l1 = 100 mm
Length l2 = 100 mm
Effective length,lb = 188 mm

Maximum reqd. thickness of plate in panel 1 = 26.99 mm


Base plate provided thickness = 36 mm
Maximum moment due to comp.stress 20.03 kNmm
6550000.00 26.99 35.59 36.00 0.989

Base plate Base plate


Moment due to Base plate
Thickness thickness
Load Comined Cσc tension (kN-m) Thickness
reqd due to reqd due to RATIO
case (N/mm2) = T/per x (l2)/2 provided
bearing tensile
(N-mm) (mm)
pressure (mm) force (mm)
RIB PLATE design :

RIB 1
lt1

RIB 2

RIB 3

picture is for representative purpose only

Design of Rib plate 1:

Yield strength of rib plate = 240 N/mm2


Influence width ,br1 = 200 mm
Cantilever length ,lr1 = 200 mm
lt1 = 100 mm
Height of scallop,hs = 35 mm
Height of rib plate 1 assumed = 500 mm
Thickness of rib plate 1 assumed = 12 mm
Permissible shear stress ,Fv = 96 N/mm2
Permissible bending stress,Fb = 158.4 N/mm2

Design of rib plate 2:


Yield strength of rib plate = 250 N/mm2
Influence width , br2 = 375 mm
Cantilever length ,lr2 = 375 mm
lt2 = 270 mm
Height of scallop,hs = 35 mm
Height of rib plate 2 assumed = 500 mm
Thickness of rib plate 2 assumed = 20 mm
Permissible shear stress ,Fv = 100 N/mm2
Permissible bending stress,Fb = 165 N/mm2
Design of rib plate 3:
Yield strength of rib plate = 250 N/mm2
Influence width , br3 = 470 mm
Cantilever length ,lr3 = 240 mm
lt3 = 140 mm
Height of scallop,hs = 35 mm
Height of rib plate 3 assumed = 620 mm
Thickness of rib plate 3 assumed = 20 mm
Permissible shear stress ,Fv = 100 N/mm2
Permissible bending stress,Fb = 165 N/mm2
RIB PLATE 1

RIB 1 -Moment RIB 1 -Shear


RIB 1 -Moment
RIB 1 -Shear
6×M 1 . 5×V t 3=
√36×M 2 +3×hc 2×V 2 Size of weld
due to due to due to
Load Comined Cσc
compressive compressive
due to tensile
tensile t 1= 2 t 2= h2c×Fb ratio
case (N/mm2)
stress , MC1(KN- stress,Vc1
stress , Mt1(KN-
stress ,
h c×Fb h c×Fv
mm) S1
mm) (KN) Vt1(KN)
(mm) (mm) (mm)
Anchor bolt size:

Grade of anchor bolt = 4.6


Dia of anchor bolt,A = 42 mm
Effective area of anchor bolt ,Ae = 0.8 x( π/4)*A2 = 1108 mm2
Yield strength of anchor bolt,Fy = 240 N/mm2
Allowable shear stress,Fv = 0.4 x Fy,or 80Mpa (minimum) = 80 N/mm2
Allowable tensile stress,Ft = 0.6 x Fy, or 120Mpa (minimum) = 120 N/mm2
Allowable Combined stress = fv / Fv +ft / Ft = 1.1
Number of bolts resisting shear = 8
11.99 131.00 10.82
SUPPORT LOAD
RY (kN) RX (kN) RZ (kN) V/per (kN) T/per (kN) fv = V/per /(Ae)
NO CASE
38 51 487.01 -31.3 -13.9 0.00 14.00 0.00
38 52 74.68 -40.4 3.2 5.07 65.20 4.58
38 53 169.63 -19.8 17.1 0.00 40.40 0.00
38 54 -20.39 25.4 -12.4 3.53 101.50 3.19
38 55 74.76 46.0 1.5 5.75 70.30 5.19
38 56 -6.67 -18.9 -13.5 2.90 21.70 2.62
38 57 98.44 1.7 4.1 0.00 0.00 0.00
38 58 -24.94 -18.9 -11.4 2.76 20.50 2.49
38 59 70.14 1.7 2.5 0.00 0.00 0.00
38 100 372.10 -55.7 -9.4 0.00 63.10 0.00
38 101 448.06 -39.2 1.7 0.00 44.90 0.00
38 102 296.04 -3.0 -21.9 0.00 0.00 0.00
38 103 372.16 13.5 -10.8 0.00 0.00 0.00
38 104 307.02 -38.5 -22.8 0.00 24.20 0.00
38 105 391.11 -22.0 -8.7 0.00 9.10 0.00
38 106 292.40 -38.5 -21.1 0.00 25.50 0.00
38 107 368.47 -22.0 -9.9 0.00 10.40 0.00
38 108 343.37 -28.7 -29.2 0.00 21.30 0.00
38 109 448.22 -28.7 10.7 0.00 13.80 0.00
38 110 324.28 -21.2 -32.9 0.00 8.70 0.00
38 111 350.08 -28.9 -29.2 0.00 21.10 0.00
38 112 330.99 -21.4 -32.9 0.00 8.60 0.00
38 113 429.13 -21.2 6.9 0.00 4.00 0.00
ROARK'S TABLES FOR USE IN DECIDING BASE PLATE THICKNESS
( Reproduced from the book " Formula for stress and strain" by Roark )

CASE 1 Three edges fixed/ continuous, one edge free


z free edge

x
a

T
Bending stress at x = 0 and z = 0
fb = -Bet1x qxb2/t2

Bending stress at x = 0 and z = b


fa = Bet2x qxb2/t2

Bending stress at x = a/2 and z = b


fa = -Bet3x qxb2/t2

Where q is the U D L on the plate and Bet1, Bet2 and Bet3 are as given below
CASE1:
a/b 0.25 0.5 0.75 1 1.5 2 3 values to be seen
Bet1 0.02 0.081 0.173 0.321 0.727 1.226 2.105
Bet2 0.016 0.066 0.148 0.259 0.484 0.605 0.519
Bet3 0.031 0.126 0.286 0.511 1.073 1.568 1.982

CASE1
values to be seen

CASE 2 Two edges fixed/ continuous, Two edges free(both adjacent)


z free edges

x
a

Bending stress at x = a and z = 0


fb = -Bet1x qxb2/t2

Bending stress at x = 0 and z = b


fa = Bet2x qxb2/t2

Where q is the U D L on the plate and Bet1 and Bet2 are as given below
CASE2
a/b 0.125 0.25 0.375 0.5 0.75 1 values to be seen
Bet1 0.05 0.182 0.353 0.631 1.246 1.769
Bet2 0.047 0.188 0.398 0.632 1.186 1.769

CASE 3 All sides fixed


z

x
a

Bending stress at x = 0 and z = 0


f = -Bet1x qxb2/t2

Bending stress at x = 0 and z = b/2


f = Bet2x qxb2/t2

Where q is the U D L on the plate and Bet1 and Bet2 are as given below

a/b 1 1.2 1.4 1.6 1.8 2 >2 CASE2


Bet1 0.3078 0.3834 0.4356 0.468 0.4872 0.4974 0.5 values to be seen
Bet2 0.1386 0.1794 0.2094 0.2286 0.2406 0.2472 0.25

CASE 4 One side fixed/continuous other three edges free

In this case the plate behaves as a cantilever and moments can be computed easily
D

h-n/3 n/3

values to be seen 0.5 0.75 a/b = 1.00


0.081 0.173 β1 = 0.265
0.066 0.148 β2 = 0.230 PANEL 1
0.126 0.286 β3 = 0.446

values to be seen 0.75 1 a/b = #REF!


0.173 0.321 β1 = #REF!
0.148 0.259 β2 = #REF! PANEL 2
0.286 0.511 β3 = #REF!
values to be seen 1.5 2 a/b = 0.00
0.727 1.226 β1 = -0.770 PANEL 3
0.484 0.605 β2 = 0.121
1.073 1.568

values to be seen 1 1.2 a/b = #REF!


0.3078 0.3834 β1 = 0.081
0.1386 0.1794 β2 = 0.016

Das könnte Ihnen auch gefallen