Beruflich Dokumente
Kultur Dokumente
User’s Guide
053 7
CAUTION: U.S. Federal law restricts this device to sale by or on the order of a licensed medical practitioner.
Outside the USA, check local laws for any restriction that may apply.
All specifications are subject to change without notice.
Document no. M1031869-01
August 2004
Points to note
• Medical electrical equipment needs special precautions
regarding electromagnetic compatibility and needs to be
installed and put into service according to the
electromagnetic compatibility information provided in the
"Technical Reference Manual" by qualified personnel.
• Portable and mobile RF communications equipment can
affect the medical electrical equipment.
• The allowed cables, transducers and accessories for the
system are listed in the “Supplies and Accessories“ catalog
delivered with the monitor.
• The equipment is suitable for use in the presence of
electrosurgery. Please notice the possible limitations in the
parameter sections and in this section.
CONTENTS
Monitor Introduction................................................................... 1 Pulse Oximetry ..........................................................................25
Performance............................................................................... 1 Non-Invasive Blood Pressure (NIBP) ...........................................29
Symbols ..................................................................................... 5 Invasive Blood Pressure .............................................................31
Monitoring Basics....................................................................... 7 Temperature .............................................................................33
Monitor Keys and Menus ............................................................. 9 Airway Gases.............................................................................35
Display Setup ........................................................................... 11 Patient Spirometry ....................................................................37
Alarms ..................................................................................... 13 NeuroMuscular Transmission (NMT) ...........................................39
Trends...................................................................................... 15 Abbreviations............................................................................41
Data Management .................................................................... 17 Messages .................................................................................47
Recording and Printing.............................................................. 19 Troubleshooting ........................................................................51
ECG ......................................................................................... 21 Cleaning and Care .....................................................................53
Impedance Respiration ............................................................. 24 Supplies and Accessories...........................................................57
MONITOR INTRODUCTION
There are two models of Cardiocap/5 monitors: hemodynamic monitor (F-MX) and hemodynamic monitor with airway gas
measurement (F-MXG). You can enhance the functions of the monitor with different factory-configured options. Due to these different
factory configurations, some menus, displays, and functions described in this manual may not be available in your monitor.
You can use the Cardiocap/5 monitor as a stand-alone monitor or connect it to the network. See “Data Management”.
–1–
Rear panel
1
(1) Built-in lifting slot
(2) Gas outlet, X6
(3) Remote Control connector, X5
(4) Ethernet connector, X4
(5) Network connection LEDs
(6) Network identification plug connector, X3
(7) Serial communication interface / local printer connector, X2
(8) Analog / digital output connector, X1
2 (includes nurse call and defibrillator synchronization
13 signals)
3 (9) Mounting attachment
(10) Dust filter
4
12 (11) Potential equalization
(12) Fuse and voltage information
(13) Receptacle for mains power cord
11 10 9 8 7 6 5
WARNING Before starting to use the system, ensure that the whole
combination complies with the international standard IEC 60601-1-1
CAUTION: Turn off the power before making any rear panel and with the requirements of the local authorities.
connections. Do not connect any external devices to the system other than those
specified.
–2–
PERFORMANCE
All specifications are subject to change without notice.
WARNING: Operation of the monitor outside the specified values may cause inaccurate results.
comply with the NIBP (IEC 60601-2-30) and Frequency of respiration sensing current: 31.25 kHz
GE Datex-Ohmeda Cardiocap/5 invasive pressure (IEC 60601-2-34) standard Maximum Tall T wave amplitude that does not disturb the
requirements. heart rate calculation time (according to ANSI/AAMI EC13
Power supply 4.1.2.1): 10 mV
Rated voltages and frequencies: ECG Pacemaker pulse detection:
100-240 VAC, 60/50 Hz detection level: 2 to 700 mV
Allowed voltage fluctuations: ± 10% Waveform display (with 50 Hz power supply
frequency): pulse duration: 0.5 to 2 ms
Maximum power consumption: 80 VA
Monitoring filter: 0.5 to 30 Hz The monitor is specified for both of the methods A
Fuses (2): T2AH/250V
ST filter: 0.05 to 30Hz and B required in ANSI/AAMI EC13 4.1.4.2.
Back-up battery Diagnostic filter: 0.05 to 100 Hz Pacer pulse rejection of fast ECG signals:
Type: 12V 2.6AH, lead acid Waveform display (with 60 Hz power supply
Back-up battery time: frequency): 0.2 V/s with Sensit pacemaker selection and 1.6
at least 15 minutes when fully charged Monitoring filter: 0.5 to 40 Hz V/s with other selections according to the test
Charging time: 5 hours (typical) ST filter: 0.05 to 40 Hz defined in ANSI/AAMI EC13 section 4.1.4.3.
Charging indicator: Diagnostic filter: 0.05 to 100 Hz
Green LED On—full charge, battery on the Minimizing the effects of the line isolation monitor Heart rate
holding voltage transients: Crystal controlled oscillator used as the Measurement range: 30 to 250 bpm
Green LED flashing—charging operating frequency source of the patient isolation power Measurement accuracy: ± 5% or ± 5 bpm
supply. Pacemaker pulse detection:
Environmental conditions Detection level: 2 to 500 mV
Offset voltage range: ±0.4 V
Operating temperature: +10 to +40°C Pulse duration: 0.5 to 2 ms
(50 to 104°F) WARNING. The ±0.4 V offset voltage range of the
The heart rate calculation operates with irregular
Storage and transport temperature: ECG measurement may be insufficient to handle the
–10 to +50°C (14 to 122°F)
rhythms of ANSI/AAMI EC13 4.1.2.1 (e) as follows:
offset potentials when using ECG electrodes of
Relative humidity: a): 40 bpm b): 87 bpm c): 60 bpm
dissimilar metals
0 to 85% noncondensing; d): 117 bpm
The isolation barrier capacitance has been
in airway 0 to 100% condensing minimized to reduce the hazard of burns in the
Atmospheric pressure: Average heart rate response time and time range of
event of a defect in the ESU return electrode
660 to 1060 hPa (500 to 800 mmHg) response time (according to ANSI/AAMI EC13
connection.
Alarm behavior Direct current for leads-off detection through any patient 4.1.2.1 (f)):
If the alarm mode is latched, the technical electrode : ≤50 nA Response time 80 to 120 bpm: 5.0s (3.7 to 6.2 s)
alarms are latched as well. This does not The normalized respiration sensing current : ≤3.0 µA Response time 80 to 40 bpm: 6.5s (4.1 to 9.2 s)
–1–
The average time and time range ( ) to alarm for
tachycardia are as follows (ANSI/AAMI EC13
Respiration Pulse Oximetry, Standard
4.1.2.1 (g)): Respiration range: 4 to 120 resp/minute Display update time: 5 seconds
Figure 4a halved amplitude: 5.5 s (4.8 to 5.9 s) Accuracy: ± 5% or ± 5 resp/minute Averaging time: adjustable
Plethysmographic waveform scaling: adjustable
Figure 4a normal amplitude: 6.6 s (4.8 to 7.2 s)
Figure 4a doubled amplitude: 7.2 s (5.3 to 9.4 s) SpO2
NIBP Calibration range: 50 to 100%
Figure 4b halved amplitude: 7.4 s (7.0 to 7.7 s)
Measurement range: Calibrated against functional saturation
Figure 4b normal amplitude: 6.2 s (4.7 to 8.1 s)
Adult 25 to 260 mmHg Measurement range: 40 to 100%
Figure 4b doubled amplitude: 6.4 s (4.4 to 8.2 s) Child 25 to 195 mmHg Measurement accuracy (% SpO2 ± 1 SD):
ST segment analysis Infant 15 to 145 mmHg 80 to 100% ± 2 digits
Measured and displayed simultaneously for up Pulse rate range accepted: 30 to 250 bpm 50 to 80% ± 3 digits
to three ECG leads Cuff pressure measurement range: Below 50% unspecified
ST level range: –6 to +6 mm (–0.6 to +0.6 mV) -15 to +350 mmHg NOTE: SpO2 measurement accuracy is based
QRS minimum detection level: on deep hypoxia studies using Datex-Ohmeda
NOTE: The cuff pressure measurement range is
Minimum level 0.5 mV with duration between Sat Sensors on volunteers. Arterial blood
equal with cuff nominal and cuff indication
40 and 120 ms fulfils ANSI/AAMI EC13 samples were analyzed by a Radiometer OSM
ranges.
standard. CO-oximeter. Refer to the sensor instructions
Display resolution: 0.1 mm (0.01 mV) Typical measuring time:
for specific SpO2 accuracy data.
Averaging: calculated from 16 QRS complexes Adult 23 seconds
Display update interval: 5 seconds Infant 20 seconds Pulse rate
Measurement range: 30 to 250 bpm
Auxiliary ECG output: Invasive Blood Pressure Measurement accuracy: ± 5% or ± 5 bpm
Bandwidth of auxiliary output: 0.5 to 40Hz Measurement range: –40 to 320 mmHg Default alarm limits**
Measurement accuracy: ± 5% or ± 2 mmHg SpO2: high Off, low 90%
Gain: 1 mV ECG signal is 1 V at the auxiliary output.
Transducer sensitivity: Pulse rate: high 160, low 40
Propagation delay: < 15 ms 5 µV/V/mmHg, 5 VDC, maximum 20 mA Limits are adjustable.***
Pulse rate Sensor emitter wavelength ranges
The pacemaker pulses are absent but may cause
Measurement range: 30 to 250 bpm Red LED: 660 nm
interference at the auxiliary ECG output. Accuracy: ± 5% or ± 5 bpm
An auxiliary device that fulfils the requirements of the IEC Infrared LED: 900 nm
60601-1 standard can be connected to the auxiliary
output. There are no other limitations, because the
Temperature Pulse Oximetry, Enhanced (N-XOSAT)
auxiliary output of the monitor is galvanically isolated from Measurement range: 10 to 45°C (50 to 113°F) Display update time: 5 seconds
patient applied part of the ECG measurement. Measurement accuracy: Averaging time: 12 seconds
25 to 45.0 °C ± 0.1 °C (77 to 113 °F ± 0.2 °F) Plethysmographic waveform scaling: automatic
10 to 24.9 °C ± 0.2 °C (50 to 76.8 °F ± 0.4 °F)
SpO2
Calibration range: 70 to 100%
–2–
Calibrated against functional saturation of approved sensors and accuracy details. FiEnf high 5.1%, low Off
Measurement range: 1 to 100% NOTE: SpO2 measurement accuracy is based EtHal high 1.5%, low Off
Measurement accuracy (± 1 SD): on testing healthy adult volunteers in induced FiHal high 2.2%, low Off
70 to 100% ± 2 digits hypoxia studies. EtIso high 2.3%, low Off
70 to 100% ± 3 digits during conditions of FiIso high 3.4%, low Off
clinical patient motion
Pulse rate EtSev high 3.4%, low Off
Measurement range: 30 to 250 bpm
Below 70% unspecified FiSev high 5.1%, low Off
Measurement accuracy: ± 3 digits
NOTE: SpO2 measurement accuracy is Non-disturbing gases:
statistically derived and correlated to Default alarm limits** Ethanol C2H5OH (< 0.3%)
simultaneous arterial blood gases measured on SpO2: high Off, low 90% Acetone (< 0.1%)
a Radiometer OSM3 CO-oximeter. Refer to the Pulse rate: high 160, low 40 Methane CH4 (< 0.2%)
sensor instructions for specific accuracy data. Limits are adjustable.*** Nitrogen N2
Pulse rate Sensor emitter wavelength ranges Carbon monoxide CO
Measurement range: 30 to 250 bpm Red LED: 660 nm Nitric oxide NO (< 200 ppm)
Measurement accuracy: ± 2% or ± 2 bpm Infrared LED: 920 nm Water vapor
(whichever is greater) Effect of helium: decreases CO2 readings
Airway Gases < 0.6 vol% typically
Default alarm limits** Maximum effect on readings:
SpO2: high Off, low 90% Sampling rate*: 200 ml/minute CO2 < 0.2 vol%,
Pulse rate: high 160, low 40 Sampling delay: 2.5 seconds typical with a N2O, O2 < 2 vol%
Limits are adjustable.*** 3 m sampling line Anesthetic agents: < 0.15 vol%
Total system response time: 2.9 seconds typical
Sensor emitter wavelength ranges with a 3 m sampling line, including Carbon dioxide (CO2)
Red LED: 650 to 665 nm sampling delay and rise time Measurement range:
Infrared LED: 930 to 950 nm Warm-up time: 0 to 15%, (0 to 15 kPa), (0 to 113 mmHg)
Average power: ≤ 1 mW 2-5 minutes, 30 minutes for full spec. Measurement rise time < 400 ms (typical)
Accuracy*: +/-(0.2 vol% + 2% of reading)
Pulse Oximetry, Nellcor® (N-XNSAT) Respiration rate (RR) Gas cross effects: < 0.2 vol% (O2, N2O,
Measurement range: 4 to 60 breaths/minute anesthetic agents)
Display update time: 5 seconds
Detection criteria: 1% variation in CO2
Averaging time: 5 to 7 seconds Oxygen (O2)
Plethysmographic waveform scaling: automatic Default alarm limits** Measurement range: 0 to 100%
EtCO2 high 8%, low 3% Measurement rise time: < 400 ms typical
SpO2
FiCO2 high 3%, low Off Accuracy: +/-(1 vol% + 2% of reading)
Calibrated against functional saturation
FiN2O high 82% Gas cross effects:
Measurement range: 1 to 100%
EtO2 high Off, low 10% < 1 vol% anesthetic agents
Measurement accuracy (% SpO2 ± 1SD):
FiO2 high Off, low 18% < 2 vol% N20
70 to 100% (± 2 digits to ± 3.5 digits,
EtDes high 12%, low Off
depending on the sensor) Nitrous oxide (N2O)
FiDes high 18%, low Off
Below 70% unspecified Measurement range: 0 to 100%
EtEnf high 3.4%, low Off
See the “User’s Reference Manual” for a list
–3–
Measurement rise time: < 450 ms typical Airway pressure (D-lite) Stimulus current range (supramax and manual):
Accuracy: +/-(2 vol% + 2% of reading) Measurement range: –20 to +100 cmH2O 10 to 70 mA with 5 mA steps
Gas cross effects: < 2 vol% anesthetic agents Accuracy*: ±1 cmH2O Stimulus current accuracy: 10% or ± 3mA
Anesthetic agent (AA) (whichever is greater)
Airway pressure (Pedi-lite)
Measurement rise time: < 400 ms typical Max load: 3 kΩ
Measurement range ***: –20 to +100 cmH2O
Halothane, Isoflurane, Enflurane Max voltage: 300 V
Gas cross effects: < 0.15 vol% N2O
Flow (D-lite)
Measurement range: 1.5 to 100 l/minute Regional block mode
Measurement range: 0 to 6% Stimulation mode: single twitch (ST)
Accuracy: +/- 0.2 vol% Flow (Pedi-lite) Intervals: 1 second, 2 seconds, 3 seconds
Sevoflurane Measurement range: 0.25 to 25 l/minute Stimulus pulse: square wave, constant current
Measurement range: 0 to 8% Compliance (D-lite and Pedi-lite) Pulse width: 40 µs
Accuracy: +/- 0.2 vol% Measurement range: 4 to 100 ml/cmH2O Stimulus current range: 0 to 5.0 mA with
Desflurane 0.1 mA steps
Measurement range: 0 to 20% Airway resistance (D-lite and Pedi-lite) Stimulus current accuracy: 20% or 0.3 mA
Accuracy*: Measurement range: 0 to 40 cmH2O/l/second (whichever is greater)
0 to 5 vol%: +/- 0.2 vol% Sensor specifications (D-lite)
5 to 10 vol%: +/- 0.5 vol% Dead space: 9.5 ml Recorder
10 to 20 vol%: +/- 1.0 vol% Resistance at 30 l/minute: 0.5 cmH2O Principle: thermal array
Agent identification Print resolution:
Identification threshold*: 0.15 vol% Sensor specifications (Pedi-lite)
Dead space: 2.5 ml Vertical: 8 dots/mm (200 dots/inch)
Patient Spirometry Horizontal: 32 dots/mm (800 dots/inch) at
Detection through D-lite™ or Pedi-lite™ flow Resistance at 10 l/minute: 1.0 cmH2O
speed of 25 mm/second and slower
sensor and gas sampler with following
specifications:
NMT Paper width: 50 mm; printing width 48 mm
Traces: selectable; 1, 2, or 3 traces
Tidal volume (D-lite) Stimulation modes:
Print speed: 1, 6.25, 12.5, 25 mm/second
Measurement range: 150 to 2000 ml Train of four (TOF)
Accuracy*: ± 6% or 30 ml Double burst (3.3) (DBS)
* Typical value
Tidal volume (Pedi-lite) Single twitch (ST)
50 Hz tetanic + post-tetanic count (PTC) ** Alarm limits and their adjustment range
Measurement range: 15 to 300 ml
Measurement intervals: may vary depending on the mode used.
Accuracy*: ± 6% or 4 ml
TOF and DBS: manual; 10 seconds, *** The user may set the SpO2 low alarm
Minute volume (D-lite)
12 seconds, 15 seconds, 20 seconds, limit lower than 80% and Ppeak alarm
Measurement range: 2 to 20 l/minute
1 minute, 5 minutes, 15 minutes limit higher than 50 cmH2O during
Accuracy*: ± 6%
ST: manual; 1 second, 10 seconds, normal use of the monitor. To guarantee
Minute volume (Pedi-lite) 20 seconds
Measurement range: 0.5 to 5 l/minute patient safety, the user cannot save such
Accuracy*: ± 6% Stimulator limits as user default values.
Stimulus pulse: square wave, constant current
Pulse width: 100, 200 or 300 µs
–4–
SYMBOLS
Attention, consult accompanying documents. Type CF (IEC-60601-1) defibrillator-proof
protection against electric shock.
When displayed beside the O2 value, indicates
that FiO2 low alarm limit is set below 21%. Indicates the beats detected.
When displayed next to the HR value, indicates
that there is a risk that the monitor counts Respiration rate is measured using impedance
pacemaker spikes because the pacer is set on R, respiration measurement.
or T-waves because a wide QRS is selected.
Appears in the message field when the alarms
On the front panel indicates that protection are silenced. Appears in the digit field or a menu
against cardiac defibrillator discharge is due in when the alarm source is selected off.
part to the accessories for pulse oximetry (SpO2),
temperature (T) and invasive pressure (P) Back-up battery operation and remaining
measurement. capacity
–5–
Ethernet connectors
Alternating current
Fuse
Date of manufacturing
–6–
MONITORING BASICS
• Check that you have the desired waveforms and digits in the
Preparation fields. See “Display Setup”.
• Turn on the monitor. See Monitor Keys and Menus.
• Carry out measurement-specific startup. See the
• Tilt the monitor to the optimal viewing angle: corresponding measurement section in this guide.
Press the center of the foot and adjust. • Enter patient identification data:
Make sure both feet are at the same angle. Press the ComWheel and select Patient Data.
See “Data Management”.
During monitoring
• To suppress alarms, press Silence Alarms.
• If you press the Power On/Standby key accidentally during
monitoring, press the Power On/Standby key within eight
seconds to return to monitoring. Otherwise, the monitor will
switch to standby mode after eight seconds.
If wall mounting solutions are used, make sure the monitor’s Ending monitoring
front and back attachment bars fit tightly to the edges of the
• Print necessary information. See “Recording and Printing”.
mounting plate and the locking bolt in the monitor’s back
locks into place. • Wait until printing is finished. Then clear patient
identification data and return settings to their defaults:
• If necessary, change the operating mode:
Press the ComWheel and select Reset Case.
Press the ComWheel. Select Monitor Setup and Select Mode.
NOTE: Changing the mode also changes some settings, such Select Reset ALL and YES.
as alarm limits. • Turn the power switch to standby if the monitor will not be
used. Clean the monitor according to the instructions.
Starting monitoring
• Prepare the patient connections. See the corresponding
measurement section in this guide. Use only supplies and
accessories approved by the manufacturer.
• Alarms and the parameter default settings become active.
Review alarm limits. See “Alarms”.
–7–
–9–
MONITOR KEYS AND MENUS
You can control monitoring with the ComWheel, direct access keys, or the Remote Control. The ComWheel, the main navigating tool,
provides access to all menu functions. With the direct access keys, you can control most frequently-used functions.
1
(1) Power On/Standby key
NOTE: The monitor will start only when connected to mains power.
(2) Silences an active alarm or pre-silences all alarms for two minutes (press
the key once) or for five minutes (press the key for three seconds). To clear
2 the alarm message field of all alarm messages and to enable new alarms,
Silence
Alarms press the key again.
Trends 3 (3) Displays numerical or graphical trends, and snapshots.
(4) Displays the Invasive Pressures menu to adjust Invasive Pressure
4 measurement settings.
Invasive
Pressures NOTE: Depending on the options, this key may be Pulse Oximetry or NMT.
ECG 5 (5) Displays the ECG menu to adjust ECG measurement settings.
(6) Displays the NIBP menu to adjust NIBP measurement settings.
NIBP
6 (7) Starts a single non-invasive blood pressure measurement or cancels single
NIBP measurement, STAT and manual measurements, and stops venous
NIBP
7 stasis.
Start/Cancel
(8) Returns to normal monitoring display.
Normal
Screen (9) ComWheel. Menu functions are controlled by turning and pressing the
8
ComWheel. Opens the Main Menu when no other menu is displayed
.
–9–
Moving in menus Remote Control
A menu is a list of functions or commands displayed on the The Remote Control gives you access to the same menus as the
monitor screen. direct access keys on the monitor. When using the Remote
You open the Main Menu by pressing the ComWheel when no Control, you can enter all monitoring functions by pressing the
other menu is displayed. You can enter other menus from the Menu key, and the most common functions by pressing the direct
Main Menu by turning and pressing the ComWheel. Turn and access keys.
press the ComWheel to make adjustments in menus.
You can also display a menu by pressing the corresponding
direct access key. For example, to adjust the ECG display:
1. Press the direct access key to open the menu. Silence
Alarms
ECG
Take Record
Snapshot Wave
Zero ALL
2. Turn the ComWheel to choose a function in the Pressures
Special Other
window. Patients
Start
Wedge
Start C.O. Start NIBP
3. Press the ComWheel to open a submenu or an
adjustment window. Freeze
or Menu Normal
Screen
Press the ComWheel to confirm a selection.
4. Press the Normal Screen key to return to the
Normal
Screen normal monitoring display. NOTE: The Special and Start C.O. keys are not in use with
Cardiocap/5
– 10 –
DISPLAY SETUP
Setting up the display
Monitor Setup Modes determine how the information is presented (what is
displayed on the screen and trends, etc.) and what the alarm
Screen Setup limits are. Modes are preconfigured.
The monitor starts in startup mode, which is one of your monitor
modes chosen during configuration. To change it:
Sweep Speeds 1. Press the ComWheel and select Monitor Setup.
2. Select Select Mode and choose from the options.
Select Mode
Modifying the display temporarily
1. Press the ComWheel and select Select Mode.
Time and Date In the corresponding submenu, you can modify waveform and
digit field measurements, minitrend length, and sweep speeds
or choose the split screen option.
Display Brightness 100%
2. To make other setup changes, like scale changes:
Return to the Main Menu and select a desired parameter.
Install/Service or
Press a direct access key and select the setup menu for that
Main Menu parameter.
Changes are valid until the monitor is turned off (+15 minutes) or
until you reset the case. Only the time and date are stored
permanently.
Return to Main Menu.
Modifying the display permanently
You can make permanent changes in the display setup. To find
out about passwords, etc., refer to the “User’s Reference Manual”.
– 11 –
Setting the time and date Modifying digit fields
The clock format is 24 hours. A Cardiocap/5 monitor that is You can display data in up to four digit fields.
connected to the monitor network follows the time and date 1. Press the ComWheel and select Monitor Setup.
settings of the network. 2. Select Screen Setup.
1. Press the ComWheel and select Monitor Setup. 3. Select Digit Fields.
2. Select Time and Date and adjust the time (hour, minutes, zero NOTE: When fewer than four digit fields contain data, the
seconds) and date (day, month, year). remaining fields are enlarged in most cases.
To prevent the loss of trend data, time settings cannot be
changed after the case is reset. Modifying split screen
You can split a waveform display so that one part of it displays
Modifying waveform fields spirometry or trend data all the time.
You can have up to six waveforms on the display at a time. 1. Press the ComWheel and select Monitor Setup.
1. Press the ComWheel and select Monitor Setup. 2. Select Screen Setup.
2. Select Screen Setup. 3. Select Split Screen and choose from the options:
3. Select Waveform Fields. None, Spiro1, Spiro2 or Trend.
NOTE: • Spiro1 is a basic view of spirometry information.
• When fewer than six waveforms are displayed, the • Spiro2 is a basic view with additional values.
remaining waveforms are enlarged in most cases. • Trend is a minitrend of the parameters that have been
• Selecting Combine Pressures displays invasive pressures in the selected to the waveform field.
same waveform field with the same zero line but with
individual scales.
• If a 5-lead set is used in the ECG measurement, up to three
different ECG leads can be displayed simultaneously in
different fields.
– 12 –
ALARMS
After the monitor is turned on or after the case is reset, the alarm limits are activated only when the physiological signals have been
inside the alarm limits for 15 seconds. To enable the alarms, connect the patient cables. Alarms are operative even when the
measurement is not selected on the screen (except for the respiration measurement), unless the source is selected OFF.
2
Tachy 1 When an alarm becomes active:
ECG
H (1) Messages appear in order of priority.
58
Pacer 1mV R
hidden
/min
(2) The measurement value and the alarm
LED flash. The background color
mm Learning signifies the alarm category.
1mV S
T II 0.9 (3) A message gives more detailed
V5 0.0
aVL 0.0 0.9 information in some cases.
An audible alarm sounds.
3
Alarm categories
The priority depends primarily on the cause and alarm duration.
– 13 –
Adjusting limits Suppressing audible alarms temporarily
1. Press the ComWheel and select Alarms Setup. For two minutes: Press the Silence Alarms key.
2. Select Adjust Limits and highlight the measurement. For five minutes: Press the Silence Alarms key for more than three
seconds.
3. Press the ComWheel. An adjustment window appears.
If the alarms are not active when you press the Silence Alarms key,
4. In the adjustment window, turn the ComWheel to change the
they are pre-silenced for two or five minutes.
limits. Press the ComWheel to confirm the selection and to
move between selections. Exception: FiO2 <18%, EtO2 <10%, FiN2O >82%, and high Ppeak
alarms are silenced for 20 seconds. New alarms are displayed.
Changing sources • To reactivate alarms, press the Silence Alarms key during the
For NIBP, P1, P2, O2, AA, T1, and T2 you can select which silencing period.
measured values trigger the alarm. For example, for pressures New alarms are activated. Silenced alarms are active after two
the possibilities are systolic, diastolic, mean value, or OFF. minutes. Apnea alarm is activated after five breaths.
Only the last modified source is active.
1. Press the ComWheel and select Alarms Setup. Suppressing audible alarms permanently
2. Select Adjust Limits and select the measurement. 1. Press the ComWheel and select Alarms Setup.
3. In the adjustment window, press the ComWheel as many 2. Select Audio ON/OFF.
times as required to get to the menu selections. 3. Select Silence Apnea, Silence ECG, Silence Apn&ECG, or Silence ALL.
4. Select the alarm. If an active alarm is suppressed, a reminder beep appears every
two minutes.
Receiving other site alarms (with N-XNET or N-XDNET option) • To reactivate alarms, select Activate Alarms.
The monitor needs to be connected to the network.
1. Press the ComWheel and select Patient Data. WARNING: Always make sure that necessary alarm limits are set
and active when you start monitoring.
2. Select Other Patients.
3. Select Receive Alarms and choose a site. WARNING: Suppression of alarms may compromise patient safety.
Adjusting volume
1. Press the ComWheel and select Alarms Setup.
2. Select Alarm Volume.
– 14 –
TRENDS
Graphical trend view Trends view
(1) Trends menu
1 2 3 (2) Measurement trend field
(3) Real time ECG or measurement trend field
aVR (4) Numeric value of a measurement at the trend cursor point
Trends Pacer 1mV
hidden (5) Trend page number
Take Snapshot
HR 240 100SpO2
(6) Time and marker field
Next Page 58
97
90
4 Symbols
Print Page 120
Cursor 0 80
Time Scale
Art 200 128/81 20 CVP Trend bar. Gap shows the mean value.
20 NIBP (12)
100 10
Graphical
0 0
Snapshot
CO2 6 5.0/0.0 10 AA NIBP trend bar.
Numerical 4 3.0/2.3
5
Trend Scales 2
0 0 Indicates change, such as change of the ECG lead,
Remove Menu
O2 100 21/16 100N2O zeroing of the invasive blood pressure channel, or
Main Menu 77/77 change of the anesthetic agent.
50 50
Show graphical
0 0 Blue line indicates the point from which the data
trends. Mark Trend have been gathered.
Event 8:25 8:30 8:35 8:40 1/4 5
White line indicates the proportion of data you see
on the screen.
6
Red line indicates the time period during which
20 minutes of trend data have been gathered.
Adjust the parameter and time scales to see the desired trend detail.
– 15 –
Automatic and manual information gathering Creating snapshots and placing markers in trends
The monitor displays two types of trend information: graphical Snapshot is a frozen frame containing 15 seconds of real-time
and numerical. You can also create snapshots of the waveforms (preconfigured waveforms and trends) that are saved
information. to the monitor memory.
1. Press the Trends key.
Viewing graphical trends 2. Select Take Snapshot.
1. Press the Trends key. The monitor saves an image of preconfigured waveforms and
2. Select Graphical. trends. You can take up to 16 snapshots depending on the data
3. To see more parameters, select Next Page. load.
4. To see more data, select Cursor and scroll the ComWheel. When creating a snapshot, a marker is placed in the trends. A
Graphical trends contain up to four trend pages, each of which number beside the numerical trend indicates this marked event.
has up to five fields with different parameters.
Viewing snapshots
The graphical trend time scale varies from 20 minutes to
1. Press the Trends key.
24 hours, the resolution from 10 seconds to 12 minutes. With the
20 minute trend you see data from the last 1/2 hour; with other 2. Select Snapshot.
lengths from the last 24 hours. For HR and temperature you can 3. Select Next Snapshot.
select the scale in the Trend Scales menu.
Turn the ComWheel to move to the next snapshot. In the upper
right hand corner, you can see the time the snapshot was
Viewing numerical trends created. You can display five fields on the snapshot page. You
1. Press the Trends key. can print six fields.
2. Select Numerical.
3. To see more parameters, select Next Page. Erasing trends and snapshots
4. To see more data, select Cursor and scroll the ComWheel. 1. Press the ComWheel to open Main Menu and select Reset Case.
Numerical trends contain three pages of a maximum of 24 hours 2. Select Reset Trends.
of trend data. On the top of each page is a real-time ECG NOTE: Trend data will be stored in memory for 15 minutes after
waveform. the power has been turned to Standby.
– 16 –
DATA MANAGEMENT
Collecting and saving information
The Cardiocap/5 monitor continuously collects and saves
patient data such as trends. Saving is activated when the
monitor receives vital signs.
Information is saved to:
• Monitor memory
The most recent case is saved to the monitor memory if
neither the network or memory card is in use.
• Data memory card (with N-XDNET option)
Up to 48 hours of information, depending on the data load,
can be saved to the Data card.
• Network (with N-XNET or N-XDNET option)
When the monitor is connected to the monitor network,
cases from 2-90 days (depending on the configuration) can
be saved to it.
– 17 –
Retrieving information Viewing other site alarms (with N-XNET or N-XDNET option)
1. Press the ComWheel and select Patient Data. With a networked Cardiocap/5, you can view the alarms of
another monitor on the same Central Network.
2. Select one of the following:
To do this:
• Load Prev. Case
Loads the most recent case when less than 15 minutes has 1. Press the ComWheel and select Patient Data.
elapsed since you turned off the system. If the monitor 2. Select Other Patients.
has been on but not reset, you can retrieve the last case 3. Select Receive Alarms.
from the previous 24 hours. 4. Select the site you wish to view.
• Patient from Net. (with N-XNET or N-XDNET option)
Loads a case from the network. The last 24 hours of Using the Data card (with N-XDNET option)
information is retrievable. The Data card is for storage and transfer of trend data.
• Patient from Card (with N-XDNET option) The N-XDNET option lets you load collected patient data from
Loads a case from the Data card. The last 24 hours of the Data card. Saved trend data can be transferred to and
information is retrievable. viewed at other monitors (Cardiocap/5, S/5, AS/3, or CS/3).
You can also continue collecting data at another site:
Viewing other sites (with N-XNET or N-XDNET option)
1. End the case and remove the Data card from the first
With your Cardiocap/5 monitor you can see the numerics,
monitor.
waveforms, and alarms of another monitor if both monitors are
connected to the monitor network. 2. Insert the Data card in the receiving monitor.
To do this: 3. Press the ComWheel and select Patient Data.
1. Press the ComWheel and select Patient Data. 4. Select Patient from Card.
2. Select Other Patients. NOTE: Make sure the internal clocks of the two monitors are
synchronized.
3. Select Show Vital Signs.
4. Select the site you wish to view.
CAUTION: Do not subject memory cards to excessive heat, bending, or
magnetic fields.
– 18 –
RECORDING AND PRINTING
You need Recording waveforms
• Built-in recorder for recordings
To record waveforms, press the Record Waveform/Stop
• Thermal paper for the recorder key.
• Laser printer for printouts
To stop recording, press Record Waveform/Stop again.
NOTE: Recordings on thermal paper may be destroyed when To configure the waveform recording:
exposed to light, heat, alcohol, etc. Take a photocopy for your
1. Press the ComWheel to open Main Menu and select
archives.
Record/Print.
2. Select Record Waveforms.
3. Select Waveform 1, Waveform 2 or Waveform 3 and choose the
parameter(s) for up to three waveforms.
4. Select Delay to choose when to start the recording:
(0, for recording only real-time data, or 12 seconds).
5. Select Paper Speed to adjust the paper speed (slower speeds
result in sharper images).
6. Select Length and choose the recording time (30 seconds or
continuous).
Recording on alarms
1. Press the ComWheel and select Record/Print.
2. Select Record Waveforms.
(1) Record Waveform/Stop key to start recording selected real-time 3. Select Start on Alarms and YES.
waveforms and to stop recording Recording is activated by Asystole, HR High/Low or P1
(2) Record Trend/Stop key to start recording a numerical trend or High/Low.
selected graphical trend and to stop recording P1 and ECG waveforms are recorded. Selections are
preconfigured.
(3) Key to release the recorder paper compartment
(4) Recorder paper
(5) Recorder paper compartment
– 19 –
Recording trends Printing
Trends are recorded from the time period that corresponds to Selecting a printer
the Time Scale setting (20 minutes to 24 hours) in the Trends menu. 1. Press the ComWheel to open Main Menu and select
To record the default trend (numerical or graphical), Record/Print.
press the Record Trend/Stop key. 2. Select Printer Connection.
To stop recording, press Record Trend/Stop again. • If the printer is connected directly to your monitor, select
Serial.
To configure the trend recording:
• If your monitor and printer are connected to the monitor
1. Press the ComWheel to open Main Menu and select network, select Net.
Record/Print.
2. Select Record Trends. Printing one view
You can print one loop or the currently viewed trend data in the
3. To change the resolution, select Trend Resolution and choose
corresponding parameter menu.
the time (1, 5, 10, or 30 minutes).
To print a loop:
4. To select the parameters for the graphical trends, select
Graphic. Trend 1 or Graphic. Trend 2 and choose the parameter. 1. Press the ComWheel and select Parameters.
Adjust the parameter and time scales to see the desired trend 2. Select Airway Gas.
detail. 3. Select Spirometry Loops and Print Saved.
To print trend data:
1. Press Trends.
2. Select the trend type you wish to print (Graphical, Snapshot or
or Numerical).
3. Select the desired trend page with Next Page.
4. Select Print Page.
Adjust the parameter and time scales to see the desired trend
detail.
Printing all information
To print all graphical trend data or all saved loops:
1. Press the ComWheel and select Record/Print.
2. Select Print Graphical or Print Loops.
– 20 –
ECG
You need
(1) ECG electrodes (pre-gelled electrodes
are recommended) Standard electrode positioning with
(2) Trunk cable Modified positioning with a a 5-lead set.
Standard electrode positioning with 3-lead set (when a CB5 lead is Place the fifth electrode in one of
(3) 3-lead set or 5-lead set
a 3-lead set. desired with a 3-lead set). the six places indicated.
Red (IEC) Yellow (IEC) Red (IEC) Red (IEC) Yellow (IEC)
White (AAMI)
1 White (AAMI)
Lead I
Black (AAMI) White (AAMI) Black (AAMI)
Lead III
1 2
3 6
4 5
Lead II Lead I
Green (IEC) Green (IEC) Yellow (IEC) Black (IEC) Green (IEC)
Red (AAMI) Red (AAMI) Black (AAMI) Green (AAMI) Red (AAMI)
WARNING: Make sure that the lead set clips or snaps do not touch any electrically conductive material, including earth.
– 21 –
3. Select Waveform Fields and select the fields (up to three) for
Selecting a lead ECG measurement.
With a 3-lead set you can monitor one lead at a time. With a
5-lead set you can monitor three different leads at a time. Viewing a cascaded ECG
• To select monitored leads, press the ECG key and select With both types of lead sets, you can display one lead in
ECG1 Lead, ECG2 Lead, or ECG3 Lead. cascaded form, in up to three waveform fields. This means the
signal continues on selected fields.
Improving waveform readability 1. Ensure that several waveform fields have ECG measurement.
1. Press the ECG key. 2. Press the ECG key, select a lead, and choose Casc.
2. Select ECG Size and increase the scale height.
NOTE: The module input circuits are protected against the WARNING: Ensure proper contact of the return electrode of the
effects of electrosurgery and defibrillation. However, the ECG electrosurgery unit to your patient to avoid possible burns at ECG
waveform on the monitor screen may be disturbed during electrode or other probe sites.
electrosurgery.
Monitoring the ST segment
Changing the HR source The monitor analyses changes in the ST segment when you are
If the ECG signal is affected by too much noise to produce a monitoring ECG. The changes are analyzed from the active
reliable heart rate calculation, choose the rate to be calculated leads.
from pressure (Art) or plethysmographic pulse waveform (Pleth). 1. To enter the ST Analysis View, press the ECG key and select
The selection is shown above the numerical display of the heart ST Analysis.
rate. 2. For optimal results, select STfilt to be the filter and one of the
1. Press the ECG key. following leads:
2. Select ECG Setup. • with 5-lead set: II, V5, and aVF.
3. Select HR Source. • with 3-lead set: II.
AUTO selects the first available of ECG, Art, ABP, and Pleth. You can also connect a 3-lead set to a 5-lead trunk cable. The
combination functions as a 3-lead set.
Viewing several leads NOTE: ST segment changes may be affected by myocardial
ischemia or other factors, such as drugs, metabolic disturbances,
With a 5-lead set you can monitor up to three different leads at a
or conduction disturbances.
time, each one in its own waveform field.
1. Press the ComWheel and select Monitor Setup. For details about detection performance and test results of
ST segment measurement testing, see "User’s Reference
2. Select Screen Setup.
Manual: ECG."
– 22 –
NOTE: A clinician must analyze the ST segment changes in WARNING: The impedance respiration measurement may cause rate
conjunction with other clinical findings. changes in Minute Ventilation Rate Responsive Pacemakers. Set
the pacemaker rate responsive mode off or turn off the impedance
Monitoring Pacemaker Patients respiration measurement on the monitor.
1. Press the ECG key.
WARNING: Do not rely entirely upon rate meter alarms when
2. Select ECG Setup - Pacemaker and select one of the monitoring patients with pacemakers. The monitor may count the
following: pacemaker pulses as heartbeats. In this case, asystole and
• Show = Pacemaker spike is displayed on ECG. ventricular fibrillation may go undetected. Always keep these
• Sensit = Sensitive pacemaker detection; spike displayed patients under close surveillance and monitor their vital signs
on ECG carefully.
• ON R = Pacemaker suppression weakened; asystole
alarm may not be reliable with active pacemakers.
• Hide = Pacemaker spike is not displayed on ECG.
NOTE: Pacemaker detector may not operate correctly during the
use of high-frequency (HF) surgical equipment. The
disturbances of HF surgical equipment typically cause false
positive pacer detection.
– 23 –
IMPEDANCE RESPIRATION
NOTE: The respiration measurement is recommended only for patients over three years old.
– 24 –
PULSE OXIMETRY
You need
• Reusable or adhesive SpO2 sensor (examples shown below).
• A separate cable is required for some sensors. Refer to Sensor Instructions for Use for details on sensor site selections and cleaning
instructions.
OxyTip+ Ear Sensor. Similar in appearance to finger sensor, but smaller. Recommended for short
to medium term monitoring. Designed for use on adult and pediatric patients > 10 kg (22 lbs)
OxyTip+ Wrap Sensor. Recommended for short to medium term monitoring. Ideal for high
motion environments if used with adhesive tape. Recommended for fragile skin if used with foam
wrap. Ideal for patients with long fingernails, acrylic nails or arthritic fingers. May be used on
fingers and toes and on the fleshy part of hands and feet on patients 3 - 20 kg (6.6 - 44 lbs).
Designed for use on patients > 3 kg (6.6 lbs)
Adhesive Sensors Description
OxyTip+ Sensitive Skin Sensor. Semi-reusable sensor designed for use from premature infants < 3
kg (6.6 lbs) through small adults. Recommended for medium to long term monitoring. Ideal for
patients with long fingernails or acrylic nails. May be used on hands, feet, fingers and toes.
OxyTip+ Adult/Pediatric adhesive sensor, for use on fingers or toes. Recommended for short to
long term monitoring in high motion environments, low-perfusion conditions. Ideal for infection
control. Designed for use on patients > 20 kg (> 44 lb). A separate sensor cable snaps into the
connector on sensor.
Adhesive sensor with integrated cable; wraps around a finger or toe. For use with N-XNSAT
option only.
– 25 –
OxyTip+ AllFit adhesive sensor for use on fingers, toes and the fleshy part of hand or foot
depending on patient weight. Recommended for short to long term monitoring in high motion
environments, low-perfusion conditions. Ideal for infection control. Designed for use on all
patient weight ranges. Ideal for patients with arthritic fingers, long or acrylic finger nails.
NOTE: Datex-Ohmeda OxyTip+ sensors are latex-free, PVC free and Cadmium free.
Applying sensors
WARNING: Discard a damaged sensor or cable immediately. Never repair a damaged sensor or cable; never use a sensor or cable repaired by
others.
WARNING: Use clean and dry sensors and cables only. Moisture and debris on connectors may affect measurement accuracy.
• Choose a well-perfused site. Refer to the sensor packaging or instructions to choose the correct sites for a specific sensor.
• Clean the application site.
Finger sensor: remove nail polish and artificial fingernails; clip long fingernails. Ear sensor: remove earrings. Positioning sensor
over a pierced area may adversely affect the SpO2 reading.
• Attach the sensor cable to the wrist or bed clothes to prevent the cable and sensor from moving.
– 26 –
Monitor connections Cable connections
Datex-Ohmeda standard
pulse oximetry
Datex-Ohmeda enhanced
pulse oximetry
(N-XOSAT option)
– 27 –
Displaying pulse rate Measuring limitations
The heart rate can originate from various sources.
WARNING: Data validity. Conditions that may cause inaccurate
To display the pulse rate measured with pulse oximetry:
readings and impact alarms include interfering substances,
1. Press the Pulse Oximetry key. excessive ambient light, electrical interference, ventricular septal
or
defects (VSD), excessive motion, low perfusion, low signal strength,
Press the ComWheel. Select Parameters and Pulse Oximetry.
incorrect sensor placement, poor sensor fit, and/or movement of
2. Select HR Source. the sensor on the patient.
3. Select Pleth. • Use Cardiocap/5 pulse oximetry only for patients weighing
5 kg (11 lb.) or more, even if the SpO2 sensor can be used for
Adjusting SpO2 settings patients weighing less than 5 kg.
You can adjust the volume of the beat sound, the waveform
• The pulse oximeter cannot distinguish between
scaling, and response averaging time.
oxyhemoglobin and dyshemoglobins (for example,
NOTE: With the N-XOSAT or N-XNSAT option, waveform methemoglobin or carboxyhemoglobin).
scaling is set to AUTO. Response averaging time is set to
• Ambient light, electrosurgery, intravascular dyes and vaso-
12 seconds for N-XOSAT or 5-7 seconds for N-XNSAT.
constrictive drugs may affect the accuracy of the
1. Press the Pulse Oximetry key. measurement.
or
• Do not use the pulse oximeter with magnetic resonance
Press the ComWheel. Select Parameters and Pulse Oximetry. imaging (MRI).
2. Select Beat Sound Volume.
• Poor perfusion may effect the accuracy of measurement
3. (Standard pulse oximetry only) Select Pleth Scale and when using the ear probe.
SpO2 Response.
– 28 –
NON-INVASIVE BLOOD PRESSURE (NIBP)
You need Cuff size Color Limb circumference Hose
(1) Cuff hose Child Green 12-19 cm Adult - Black
(2) Cuff of correct size Small adult Royal Blue 17-25 cm Adult - Black
Adult Navy Blue 23-33 cm Adult - Black
Adult Long Navy White 23-33 cm Adult - Black
Long Adult Wine 31-40 cm Adult - Black
Large Adult Long Wine 31-40 cm Adult - Black
Thigh Brown 38-50 cm Adult - Black
Infant Orange 8-13 cm Infant - White
Neonatal #3 White 6-11 cm Infant - White
Neonatal #4 White 7-13 cm Infant - White
Neonatal #5 White 8-15 cm Infant - White
– 29 –
Starting Stopping
The monitor sets inflation limits automatically for adults and To release the cuff pressure before the measurement is finished:
infants according to the hose used and inflation limit selected • Press the NIBP Start/Cancel key.
from the menu.
Setting cycling intervals
NOTE: When using infant cuffs the white infant cuff hose must
be used. The child selection increases the maximum inflation 1. Press the NIBP key.
pressure to 200 mmHg when using infant cuff/hoses. 2. Select Cycle Time.
3. Choose the new cycle time.
To produce a single measurement:
• Press the NIBP Start/Cancel key. Using NIBP cuff for Venous Stasis
or
1. Press the NIBP key.
Press the NIBP key and select Start Manual.
2. Select Start Ven.Stasis.
To measure automatically after set intervals:
• Press the NIBP key and select Start Cycling. Venous Stasis Venous Stasis
To measure continuously for five minutes: Maximum Inflation Pressure Time
• Press the NIBP key and select Start STAT. Infant 150 mmHg 40 mmHg 1 minute
Child 200 mmHg 60 mmHg 2 minute
During measurement
Adult 280 mmHg 80 mmHg 2 minute
• Observe the cuffed limb frequently. Measurement may
impair blood circulation.
• Make sure that tubes are not bent, pressed or stretched. WARNING: The monitor sets the inflation pressure automatically
Measurement may impair blood circulation. Intervals below according to the first measurement. Reset the case to reset the
10 minutes and STAT measurements are not recommended inflation limit before measuring a new patient.
for extended periods of time.
• NOTE: The presence of some arrhythmias during NIBP
measurement may increase the time required for the CAUTION: Vibrations during transport may disturb the NIBP
measurement. For details about the test results of the measurement.
function of NIBP measurement in the presence of
arrhythmias, see the “User’s Reference Manual”.
• Blood pressure values may be affected by a change in the
patient's position.
– 30 –
INVASIVE BLOOD PRESSURE
You need Starting
(1) Heparinized fluid bag with pressure infuser
• When doing the setup, prepare the transducer kit according
(2) Flushing set to the manufacturer’s instructions.
(3) Transducer • Ensure there is no air in the line. Refer to transducer
(4) Adapter cable for using disposable transducers manufacturer’s instructions on how to remove trapped air
from the transducer.
• Zero the transducer; open the transducer to air:
1 Press the Invasive Pressures key or press the ComWheel and
2 select Parameters and Invasive Press. Select Zero ALL.
• Open the line to the patient.
Disposable
Combining pressures
You can display two invasive pressure waveforms one on top of
Disposable the other, using an area of one normal waveform, or both
waveforms combined in the same field with the same zero line.
3 1. Press the ComWheel and select Monitor Setup.
2. Select Screen Setup.
3. Select Waveform Fields.
4
4. Select Combine Pressures and YES.
– 32 –
TEMPERATURE
You need
(1) Temperature probe
WARNING: Patient safety. To prevent patient injury, use Datex-Ohmeda temperature probes only.
– 33 –
Starting Changing temperature label
• Use Datex-Ohmeda temperature probes only. 1. Press the ComWheel and select Parameters.
• Select temperature in a digit field to include the 2. Select Temp Setup.
temperature information in the trends and to activate 3. Select T1 Label or T2 Label.
alarms.
Changing temperature unit
1. Press the ComWheel and select Parameters.
2. Select Temp Setup.
3. Select Unit and choose °C or °F.
– 34 –
AIRWAY GASES
You can monitor, for example, end-tidal CO2, inspiratory O2, N2O, and anesthetic agents.
You need
(1) Gas sampling line
(2) Y-piece
(3) Airway adapter with sampling line connector
(4) Heat and moisture exchanger including filter (HMEF)
– 35 –
Using D-fend Preventing operating room pollution
• Use the black D-fend for most cases. When N2O or volatile anesthetics are used, prevent operating
room pollution by doing one of the following:
• Use the green D-fend+ with patients who have increased
mucous secretions or infectious disease. • Return the sample gas to the patient circuit.
• Connect the exhaust line between the monitor sample gas
Starting outlet and a ventilator’s gas scavenging.
Before connecting the patient: • Connect the exhaust line only to an open scavenging system
where gas is removed at room pressure. Do not connect the
• Check that the airway adapter connections are tight and that monitor directly to a vacuum scavenging system.
the adapter is operating properly.
• Before you turn on the monitor, attach the gas sampling line CAUTION: Strong scavenging suction may change the operating
to the sampling line connector on the D-fend water trap. pressure of the monitor and cause inaccurate readings or internal
• Wait until the ‘Calibrating gas sensor‘ message disappears. damage.
– 36 –
PATIENT SPIROMETRY
In addition to airway gases, you can monitor patient lung mechanics and volumes.
You need
(1) Y-piece
(2) Spirometry tube
(3) D-lite sensor
(4) Bacterial filter
(5) Gas sampling line
Patient tubes
Spirometry connectors
– 37 –
Displaying loops Saving reference loops
The loops allow you to visually detect changes in the patient’s You can save up to six pairs (flow/volume and pressure/volume)
respiratory status. of reference loops. Both loops are saved at the same time. When
more loops are saved, the most recent one is erased from
memory.
Flow
1200
Vol 1. Press the ComWheel and select Parameters.
60
l/min ml 2. Select Airway Gas.
Vol 3. Select Spirometry Loops.
ml 4. When the current loop is drawn, select Save Loop.
5. To recall a saved loop, select Reference Loop and select the
1200 0 Paw number of the loop you wish to recall.
cmH20
0 40
Changing the loop appearance
- 60
If the flow, volume, or pressure axis of the loop is not drawn to
suit your needs, change the scaling.
– – – – Reference Loop
1. Press the ComWheel and select Parameters.
Real-Time Loop
2. Select Airway Gas.
3. Select Spirometry Loops.
1. Press the ComWheel and select Parameters. 4. Select Scaling.
2. Select Airway Gas.
3. Select Spirometry Loops. NOTE: Also read the “Airway Gases” section.
4. Select the loop type you wish to monitor.
To display patient spirometry values continuously, in Screen
Setup select split screen option Spiro1 (basic view) or Spiro2 (basic
view with additional values).
– 38 –
NEUROMUSCULAR TRANSMISSION (NMT)
You need
White White
(1) NMT sensor cable
Brown Brown
(2) MechanoSensor
or Black (grounding
(3) ElectroSensor 1 electrode
Green
Red
3
2
WARNING: Make sure the lead set clips do not touch electrically
Preparation
• Clean grease and dirt from the application area. Make sure conductive material, including earth.
the area is free of excessive hair or lesions. WARNING: Do not place the NMT stimulation electrodes on the
• Place the stimulating electrodes (brown and white) along the patient’s chest or any area with excessive hair or lesions.
ulnar nerve. Do not let the electrodes touch each other.
• Place the piezoelectric probe or recording electrodes as WARNING: Always stop the NMT measurement before handling
shown in the illustration. Secure the piezoelectric probe with stimulation electrodes.
tape.
• Start monitoring after the induction of sleep but before the Start/stop monitoring
administration of a muscle relaxant drug. 1. To start, press the NMT key and select Start-up.
The monitor measures the supramaximal current, then
begins the selected measurement.
2. To stop, press the NMT key and select Stop.
– 39 –
Suspend/resume monitoring Measuring deep relaxation
If you temporarily stop monitoring a patient, you can preserve When the neuromuscular block deepens, you receive no
the current and reference values. stimulation response. TOF% is not calculated when the count is
1. To suspend monitoring, press the NMT key and select Stop. less than four.
2. To resume monitoring the same patient, press the NMT key Relaxation Meter
and select Continue.
100 TOF% 20 4 Count 0 10 PTC 0
TOF and other stimulation modes Light Deep
You can use TOF (train of four), DBS (double burst), and ST
(single twitch) stimulation modes. TOF is the most common. To monitor the relaxation level, start tetanic stimulation
(continuous 5 seconds).
In TOF, four impulses are generated at 0.5 second intervals. The
ratio of the fourth to the first response is the TOF%. The TOF% 1. Press the NMT key.
declines as relaxation deepens. Normally, a TOF% over 90 2. Select Tetanic/PTC and select Start.
indicates adequate clinical recovery. You can view the TOF% After tetanic stimulation, single impulses are generated and the
and the number of responses, or count. number of responses is counted, resulting in PTC (Post Tetanic
NMT Count). After PTC, NMT measurements stop for one minute.
Then, the previous measurement cycle continues.
TOF% 30
Count 4 Locating nerve using regional block (Plexus) stimulation
0 20 sec 1. Set up the regional block adapter, needle, and syringe.
Connect the adapter cable to the monitor cable.
1. Press the NMT key. 2. Connect the cable to the monitor.
2. Select Stimulus Mode and choose the mode. 3. Press the NMT key.
Selecting recovery note 4. Select Cycle Time and choose the time.
If the count reaches a set limit, a single beep sounds and the 5. Select Regional Block.
‘Block recovery’ message appears. • To start the stimulation, select Run.
1. Press the NMT key. • To stop the stimulation, select Stop.
2. Select Recovery Note and choose the count limit.
– 40 –
ABBREVIATIONS
/min beats per minute, breaths per ATPS ambient temperature and C.I. cardiac index
minute pressure, saturated gas C.O. cardiac output
°C Celsius degree aw airway cal. calibration
°F Fahrenheit degree AV atrioventricular Calc calculated/derived value
µg microgram aVF left foot augmented lead Calcs calculations
A alveolar Avg. average CM Compact Anesthesia Monitor
A arm (describing location) aVL left arm augmented lead CaO2 arterial oxygen content
a arterial aVR right arm augmented lead Casc. cascaded (ECG)
a/AO2 arterio-alveolar PO2 ratio Axil axillatory temperature cc cubic centimeter
AA anesthetic agent CCM Critical Care Monitor
AaDO2 alveolo-arterial oxygen difference BAEP brainstem auditory evoked CCO continuous cardiac output
AAMI Association for the Advancement potential CcO2 capillary oxygen content
of Medical Instrumentation Bal balance gas CCU cardiac (coronary) care unit
ABG arterial blood gases bar 1 atmosphere CEL Celsius degree
ABP arterial pressure Bigem. bigeminy CISPR International Special Committee
ADU Anesthesia Delivery Unit Blad bladder temperature on Radio Interference
AirW airway temperature Blood blood temperature (C.O. cmH2O centimeter of water
Alpha, Al alpha frequency band measurement) CMRR common mode rejection ratio
AM Anesthesia Monitor Body body temperature CO carbon monoxide
Amp amplitude BP blood pressure CO2 carbon dioxide
Ant. anterior Brady bradycardia COHb carboxyhemoglobin
APN apnea BSA body surface area Compl compliance
Arrh. arrhythmia B-TO-B beat-to-beat Cont. continuous
Art arterial pressure BTPS body temperature and pressure, Contrl controlled ventilationCore
ASY asystole saturated gas core temperature
ATMP atmospheric pressure c calculated/derived value Count count of responses
ATPD atmospheric/ambient C chest CPB cardiopulmonary bypass
temperature and pressure, dry gas C(a-v)O2 arteriovenous oxygen content CPP cerebral perfusion pressure
difference CT computer tomography
– 41 –
CvO2 (mixed) venous oxygen content ET, Et end-tidal concentration Hgb hemoglobin
CVP central venous pressure EtAA end-tidal anesthetic agent Hbtot total hemoglobin
EtBal end-tidal balance gas Hemo Calcshemodynamic calculations
DEL delete EtCO2 end-tidal carbon dioxide Hemo hemodynamic
depr. depression EtN2O end-tidal nitrous oxide HHb reduced hemoglobin
Des desflurane EtO2 end-tidal oxygen HME heat and moisture exchanger
Dia diastolic pressure ET-tube, ETT HMEF heat and moisture exchanger with
Diagn diagnostic (ECG filter) endotracheal tube filter
DIFF difference exp expiratory hPa hectopascal
DIS S/5 Device Interfacing Solution F foot (describing location) HR dif heart rate difference
DO2 oxygen delivery FAH Fahrenheit degree HR heart rate
DO2I oxygen delivery index FFT fast Fourier transform ht height
DSC digital signal converter FI, Fi fraction of inspired gas HW hardware
Dyn. dynamic FiAA fraction of inspired anesthetic Hz hertz
agent
e estimated Fib fibrillation I:E inspiratory-expiratory ratio
ECG electrocardiogram FiBal fraction of inspired balance gas IABP intra-aortic balloon pump
ECG1 first ECG waveform (top) FiCO2 fraction of inspired carbon dioxide IC inspiratory capacity
ECG1/r real-time ECG FiN2 fraction of inspired N2 ICP intracranial pressure
ECG2 second ECG waveform FiN2O fraction of inspired nitrous oxide ICU intensive care unit
ECG3 third ECG waveform FiO2 fraction of inspired oxygen ID identification
ED emergency department Flow airway gas flow IEC International Electrotechnical
EDV end-diastolic volume Freq. frequent Comission
EDVI end-diastolic volume index ft foot, feet Imped. impedance; impedance
elect electrode FVloop flow volume loop respiration
elev. elevation in inch
EMC electromagnetic compatibility g gram Inf. inferior
Enf enflurane Graph. graphical Infl. inflation (limit)
ESD electrostatic discharge insp inspiratory
Eso esophageal temperature H hand (describing location) Inv. invasive
ESV end-systolic volume h hour InvBP invasive blood pressure
ESVI end-systolic volume index Hal halothane Irreg. irregular
– 42 –
ISO International Standards MetHb methemoglobin Ni-MH nickel-metal hydride
Organisation mg milligram NMT neuromuscular transmission
Iso isoflurane Min minimum NO nitric oxide
IVR idioventricular rhythm min minute NTPD normal temperature and pressure,
J joule ml milliliter dry gas
MLAEP middle-latency auditory evoked Num. numerical
K kelvin potential
kcal kilocalorie mmHg millimeters of mercury O2 oxygen
kJ kilojoule mol mole O2ER oxygen extraction ratio
kPa kilopascal Monit monitoring (ECG filter) O2Hb oxygenated hemoglobin
MRI magnetic resonance imaging OR operation room
L left (describing location) Mult. multiple Oxy oxygenation
L leg (describing location) Multif. PVCs
L, l liter multifocal PVCs P partial pressure
l/min liters/minute MV minute volume P pressure
LAN local area network MVexp expired minute volume (l/min) P(BTPS) pressure in BTPS conditions
LAP left atrial pressure MVexp(BTPS) expired minute volume in BTPS P(g-a)CO2 difference between
Lat. lateral conditions gastrointestinal carbon dioxide
LCD liquid crystal display MVexp(STPD) expired minute volume in STPD and arterial blood carbon dioxide
LED light emitting diode conditions concentration
LVEDP left ventricular end diastolic MVinsp inspired minute volume (l/min) P(g-ET)CO2 difference between
pressure MVspont spontaneous minute volume gastrointestinal carbon dioxide
LVEDV left ventricular end diastolic Myo myocardiac temperature and end tidal carbon dioxide
volume N neutral concentration
LVSW left ventricular stroke work N2 nitrogen P(STPD) pressure in STPD conditions
LVSWI left ventricular stroke work index N2O nitrous oxide P1..6 invasive pressure channel
Na sodium identification on module
MAC minimum alveolar concentration Naso nasopharyngeal temperature PA pulmonary arterial pressure
Max maximum neo neonate PA pulmonary artery
mbar millibar Net network Pa Pascal (unit of pressure)
mcg microgram NIBP non-invasive blood pressure Paced paced beats
Mean mean blood pressure Ni-Cd nickel-cadmium
– 43 –
PaCO2 partial pressure of carbon dioxide PM non-funct. REF right ventricular ejection fraction
in the arteries pacemaker non-functioning ref. reference
PAO2 partial pressure of oxygen in the PM pacemaker Resp Rate respiration rate (total) (measured)
alveoli Pmax maximum pressure Resp respiration rate (total) (set)
PaO2 partial pressure of oxygen in the Pmean mean pressure RF radio frequency
arteries Pmin minimum pressure RMS average (root mean square) power
PAOP pulmonary artery occlusion Ppeak peak pressure Room room temperature
pressure Pplat plateau (pause) pressure RQ respiratory quotient
Paw airway pressure PR pulse rate RR respiration rate (total) (measured)
Pbaro barometric pressure Prev. previous rtm rhythm
PCWP pulmonary capillary wedge psi pounds per square per inch RV residual volume
pressure pt patient EDV right ventricular end-diastolic
PE polyethylene PTC post tetanic count (NMT) volume
Pedi pediatric pts patientsPVC ESV right ventricular end-systolic
PEEP positive end-expiratory pressure polyvinylchloride volume
PEEPe extrinsic positive end expiratory PVC premature ventricular contraction RVP right ventricular pressure
pressure PVloop pressure volume loop RVSW right ventricular stroke work
PEEPe+i total positive end expiratory PvO2 partial pressure of oxygen in RVSWI right ventricular stroke work index
pressure (ICU) (mixed) venous blood s second
PEEPe+PEEPi PVR pulmonary vascular resistance
total positive end expiratory PVRI pulmonary vascular resistance SA sinoatrial
pressure (ICU) index SaO2 arterial oxygen saturation
PEEPi intrinsic positive end expiratory Px standard pressure label, x being 1, SD standard deviation
pressure 2, 3, 4, 5, or 6 SEMG spontaneous electromyogram
PEEPtot total positive end expiratory Sev sevoflurane
pressure (anesthesia) QRS QRS complex SI stroke index
PgCO2 gastrointestinal carbon dioxide Qs/Qt venous admixture Skin skin temperature
concentration SN, S/N serial number
PIC patient interface cable R right (describing location) Spiro patient spirometry
Pleth plethysmographic pulse waveform RAP right atrial pressure SpO2 oxygen saturation
PM non-capt. Raw airway resistance Spont spontaneous breathing
pacemaker non-capturing Rect rectal temperature ST ST segment of electrocardiograph
– 44 –
STAT continuous NIBP cuff inflation for Tx temperature label, x being 1, 2, 3, * with Fick equation
five minutes r 4 or one of the other label
stat static choices
STBY standby Tymp tympanic temperature
STfilt ST filter (ECG)
STPD standard temperature and V Fib ventricular fibrillation
pressure, dry gas V Run ventricular run
Surf surface temperature V Tachy ventricular tachycardia
SW software v venous
SV stroke volume V ventricular
SVC supraventricular contraction V volume
SVI stroke volume index V/Q ventilation/perfusion ratio
SvO2 (mixed) venous oxygen saturation V0.5 volume expired during the first 0.5
SVR systemic vascular resistance seconds
SVRI systemic vascular resistance index V1.0 volume expired during the first
Sys systolic pressure second
VC vital capacity
T temperature VCO2 carbon dioxide production
t time (min) Vd dead space
T(BTPS) temperature in BTPS conditions Vd/Vt dead space ventilation
T1% first stimulus as % of the reference WLAN wireless local area network
value (NMT) VO2 oxygen consumption
T1..4 temperature channel identification VO2calc calculated oxygen consumption*
on module VO2I oxygen consumption index
Tab. tabular VO2Icalc calculated oxygen consumption
Tachy tachycardia index*
Tbl, Tblood blood temperature Vol volume
Temp temperature wt weight
Trigem. trigeminy X extreme
TV tidal volume yr year
TVexp expired tidal volume (ml) yrs years
TVinsp inspired tidal volume (ml)
– 45 –
– 46 –
MESSAGES
If any problem or message persists, contact qualified service personnel.
Message Explanation
Alarms acknowledged Acknowledged alarms are silenced. (Silence Alarms key pressed during silencing period).
Air leakage NIBP: Air leakage in NIBP cuff or hose. Check connections.
Apnea No breath detected for 20 seconds (respiration or CO2 measurement).
Apnea deactivated Apnea alarm is silenced until alarm is reactivated after five breaths.
ARRWS arrh analysis OFF Arrhythmia analysis is selected for display but arrhythmia workstation is on standby or off.
Artifacts Unsuccessful NIBP, SpO2, or ECG measurement because of patient’s:
• movements
• shivering
• deep breathing
• arrhythmia or irregular beats
Calm the patient and start a new measurement.
Asystole ECG: No QRS detected in ECG.
Back-up battery failure Discharged or faulty back-up battery. Use mains power for 4 hours, then switch to battery power. If the
message reappears, contact authorized service personnel.
Batt. empty Connect the monitor to the power supply.
Batt. low About five minutes of battery operating time. Connect the monitor to the power supply.
Cable off NMT or regional block adapter cable is not connected.
Calibrate Agent ID Agent identification error. Perform gas calibration.
Check D-Fend Check that water trap and sampling line are properly attached.
Check NIBP NIBP measurement is only partially successful. Check setup.
Check sample gas out Gases: Sample gas outlet is blocked. Remove blockage.
– 47 –
Message Explanation
Check stim. electrodes NMT stimulus current could not be delivered due to poor stimulus electrode connection or damaged
cable.
Cuff loose NIBP:
Cuff occlusion • Cuff is not attached to patient.
Cuff overpressure • Cuff is too loose or hose is not connected.
• Tubes or hose are kinked.
• Cuff is squeezed during measurement.
Check NIBP cuff hose and tubes and restart measurement.
EEPROM error Memory checking failed. Contact authorized service personnel.
EMG electrodes off NMT: EMG recording electrodes are off.
Infl. limits! Check setup NIBP: Adult or child cuff is used but the infant mode has been selected.
Leads off ECG trunk cable, all lead wires, or neutral electrode (RL/N) are disconnected. ECG inoperative (offset
voltage between two electrodes is too high). Possible during defibrillation.
Measurement off NMT cable is connected but measurement has not started.
MVexp << MVinsp Exhaled volume is markedly smaller than inhaled. Check the whole system for leakage.
MVexp < 0.5l/min Measured volumes are too small for reliable calculation and, for example, waveforms and loops may be
(with Pedi-lite: unreliable.
MVexp < 0.2l/min)
NIBP manual Autocycling mode is interrupted because of air leakage or loose cuff. Check setup and restart autocycling.
No P1 transducer Invasive blood pressure transducer or cable of channel P1/P2 not connected.
No SpO2 probe Check SpO2 sensor connection.
No SpO2 pulse SpO2 pulse signal is poor. Try other measuring sites.
Noise ECG: Unreliable HR calculation or distorted waveform; possible during diathermy.
Performing temp test Monitor makes a two point calibration test for temperature immediately after the warm-up time
and after that once in 10 minutes. Test lasts 10 seconds.
– 48 –
Message Explanation
Printer failure Printer is not responding, not turned on, not connected, or not on-line.
RAM error Memory checking failed. Contact authorized service personnel.
Reference not stable The deviation between the four NMT reference stimulation responses is too big, causing reference setting
to fail.
Replace D-Fend D-fend water trap is partially blocked.
Response too weak NMT: The maximum gain is insufficient to increase the response signal amplitude to a measurable level.
This can occur if:
• Stimulation current is too weak.
• Stimulation electrodes are not connected or are improperly placed on the nerve.
• Recording electrodes are disconnected.
• One or more electrodes are dry and should be replaced.
• The skin at the electrode site is not properly prepared.
Sample line blocked Sampling line inside or outside the monitor is blocked or the water trap is occluded.
Change sampling line and/or water trap.
Sensor INOP The gas measuring sensor is inoperative or the temperature in the monitor has increased.
Contact authorized service personnel.
Setting reference NMT reference search in progress.
SpO2 probe off Check SpO2 sensor connection to patient. The finger or ear lobe may be too thin, or sensor halves are not
aligned.
SRAM error Memory checking failed. Contact authorized service personnel.
Supramaximal not found NMT: Supramaximal stimulus current (70 mA) not found.
Stop measurement, reposition stimulating or recording electrodes, and restart measurement.
Supramax search NMT: Supramaximal stimulus current search in progress.
Temperature error A repeated temperature test has failed. Contact authorized service personnel.
TETANIC NMT: Tetanic stimulation is on.
Unable to measure Dia NIBP: Accurate diastolic pressure difficult to measure because of artifacts, weak pulsation, etc.
– 49 –
Message Explanation
Unable to measure Sys NIBP: Systolic pressure probably higher than maximum inflation pressure or artifacts interfere in the
systolic area.
Unstable zero pressure NIBP: Pressure is unstable at start of the measurement. Calm the patient and retry.
Weak pulsation NIBP measuring problem:
• Improper cuff position or attachment.
• Weak or abnormal blood circulation.
• Slow heart rate associated with artifacts.
• Patient is moving
• Air leakage.
… high/… low Measured value (…) exceeds the alarm limit. Check patient condition. Adjust alarm limits.
… Lead off One of the ECG lead wires (…) is off.
– 50 –
TROUBLESHOOTING
What if … Try this …
The desired measured values do • Check that you have selected the parameter in the digit or waveform field. Press the
not appear on the screen? ComWheel to open Main Menu. Select Monitor Setup and Screen Setup.
The monitor does not start? • Connect the power cord to the power supply. The monitor will not start on battery power.
• Check the fuses. Replace if necessary.
ECG signal is noisy, or no QRS is • Ensure that the patient is not shivering.
detected? • Select the correct filter by pressing ECG and selecting ECG Setup and Filter.
Monit filters artifacts produced by the electrosurgery unit and respiration.
Diagn gives more information about the wave, but is susceptible to high frequency artifacts
and baseline wander.
STfilt gives more information about the ST segment. Filters the high frequency artifacts but
catches slow changes in the ST segment. Susceptible to baseline wander.
• Check electrode quality and positioning. Avoid placing over body hair, bones close to skin,
layers of fat and major muscles. Pre-gelled electrodes are recommended.
• Change lead.
• Enlarge the size from 1.0 mV to 2.0 mV.
Respiration measurement fails? • Check electrode quality and positioning as above.
• Adjust the detection limits. During ventilator-supported breathing the resp calculation may
count only ventilator-produced inspirations and expirations.
Other electrical devices may interfere with the measurement.
Invasive blood pressure readings are • Make sure that there are no air bubbles in transducer system. Flush and zero.
unreliable? • Place transducer on patient’s mid-heart level, and zero.
SpO2 signal is poor? • Make sure that the patient is not shivering.
• Check sensor placement.
• Be aware of differences caused by skin pigment.
• (Standard pulse oximetry only) Change averaging time from slow to normal.
– 51 –
What if … Try this …
NIBP measuring does not work or • Check that cuff tubings are not bent, stretched, compressed or loose.
values are unreliable? • Prevent motion artifacts.
• Use cuffs of correct size.
Temperature measuring fails? • Check that you have the correct kind of probe.
• Try another probe.
Airway gas values are too low? • Check the sampling line and other connectors for leakage.
• Make sure the scavenging vacuum is not too strong.
Patient spirometry values are • Check that selected Sensor Type corresponds to the sensor attached to the patient.
unreliable? • Remove D-lite and shake drops away.
• Check that connectors on D-lite are intact and all connections are tight.
NMT values are unreliable? • Clean the application site of oil and dirt.
• Check that electrodes are positioned correctly, electrode gel is moist, and skin contact is
good. Avoid placement over lesions or excessive body hair.
Cannot see some trend details? • Adjust the parameter and time scales to see the desired trend detail.
– 52 –
CLEANING AND CARE
Permitted cleaners Permitted disinfectants DO NOT!
Datex-Ohmeda Cleaning Fluid Ethanol Do not use hypochlorite, acetone-, phenol- or
Other mild detergents Isopropyl alcohol ammonia-based cleaners.
Chlorite compounds Do not autoclave the device or its parts.
Glutaraldehyde Do not immerse any part of the device in
liquids or allow liquid to enter the interior.
Do not apply pressurized air to any outlet or
tubing connected to the monitor.
– 53 –
Backup battery check Reusable D-lite sensor
1. Turn on the monitor. When the battery is fully charged, the The reusable D-lite sensor can be washed in the washing
no charging symbol should appear on the screen. machine and steam autoclaved. After washing:
2. Disconnect the monitor from mains power. The monitor • Make sure that the connectors are undamaged.
should function normally for 15 minutes. A tight connection is essential for correct measuring.
• Make sure that the sensor is dry.
Changing fuses
1. Remove the power cord. Calibrating airway gases
2. Remove the fuse holder by pushing the locking pin and Follow recommended calibration intervals (every 6th month in
gently pulling out the holder. normal use and every 2nd month in continuous use) to ensure
that measurement accuracy stays within specifications.
3. If a fuse is blown, ensure that you replace it with a fuse of
the correct type and rating. 1. Attach a regulator to the calibration gas container. See
“Supplies and Accessories”.
Other accessories 2. Attach a new sampling line to the water trap. Connect the
See the accessory package for cleaning and checking. Do not loose end of the sampling line to the regulator on the gas
reuse disposable accessories. container.
3. Turn on the monitor. Let it warm up for 30 minutes.
D-fend water trap 4. Select Gas Calibration in the Airway Gas menu.
Empty the container whenever half full. 5. Wait until the ‘Zero OK‘ and then ‘Feed gas‘ messages appear
• Black D-fend water trap: change every two months or when a after each gas on the screen.
‘Sample line blocked‘ or ‘Replace D-Fend‘ message appears. 6. Open the regulator and feed gas until ‘Adjust‘ appears.
• Green D-fend+ water trap (for patients with extensive mucus 7. Check that displayed gas values match the values on the gas
secretion and for single-patient use only): replace every 24 container. If not, adjust with the ComWheel.
hours or when a ‘Sample line blocked‘ or ‘Replace D-Fend‘ During gas calibration, % units are used for CO2 regardless of
message appears. selected measurement units.
Do not wash or reuse the D-fend water trap cartridge.
More comprehensive checking
For safe and reliable function and operation of the monitor,
regular care has to be carried out according to the instructions in
this manual and to the maintenance procedures described in the
"Technical Reference Manual."
– 54 –
Calibration check of temperature, NIBP and invasive blood Check that the pressure values are displayed.
pressures Start the Venous Stasis mode and check that the pump is not
Calibration check of temperature, NIBP and invasive blood restarting during the measurement. If it does, the cuff may be
pressures should be performed at least once a year by qualified leaking.
service personnel as a part of the Planned Maintenance, see Airway gases and Patient Spirometry
"Technical Reference Manual." Occlude the sampling line and check that the ‘Sample line
Regular checks blocked’ message appears within 30 s and gas waveforms are
When you start monitoring, check that showing zero at the same time.
• accessories are intact and properly connected. During spirometry measurement, check that the loops are
• you have selected desired parameters to be displayed on digit whole. A gap between the starting and ending points may
and waveform fields. indicate a leak.
NIBP
Ensure that you are using correct cuff size and have selected
correct inflation limits.
Check that the cuff hose detection (Adult/Child) works properly.
– 55 –
– 56 –
SUPPLIES AND ACCESSORIES
Approved and specified for the GE Datex-Ohmeda Cardiocap/5.
572683 Solid gel, Ag/AgCl, 50/pkg 8002908 Esophageal stetoscope with
ECG 572684 Safety pin for infant, 60 cm, temperature probe 18 F
Trunk cables, IEC color coding 15/pkg 8002909 Esophageal stetoscope with
545305 3-lead cable, 1.2 m m/4 ft. temperature probe 24 F
Temperature
545300 3-lead cable, 3 m m/10 ft. Reusable probes Pulse Oximetry, Standard
545304 3-lead cable, 5 m/16 ft. 165602 Skin temp probe, 1.5 m/4.9 ft. Integrated reusable sensors
545306 5-lead cable, 1.2 m m/4 ft. 16560 Skin temp probe, 3.5 m/11.5 ft. OXY-E4-N OxyTip+ integrated Ear Sensor
545301 5-lead cable, 3 m/10 ft. 165622 Central temp probe, adult, 4 m / 13 ft.
Lead sets, IEC color coding 1.5 m/4.9 ft. OXY-F4-N OxyTip+ Finger, 4 m/13 ft.
545315 3-lead set, clip, 0.75 m/30 in. 16561 Central temp probe, adult, Intergrated reusable sensors (OXY-C cable
8001960 3-lead set, clip, 1.5 m/60 in 2.8 m/9 ft. required)
545316 5-lead set, clip, 1.25 m/49 165612 Central temp probe, pediatric, OXY-F-DB OxyTip+ Finger, 2 m/6.5 ft.
in.(leg) and 75 cm/30 in (chest) 1.5 m/4.9 ft. OXY-W-DB OxyTip+ Wrap, 2 m/6.5 ft.
8001961 5-lead set, clip, 1.5 m/60 in 165611 Central temp probe, pediatric, OXY-E-DB Interconnect ear sensor with
Trunk cables, AAMI color coding 2.8 m/9 ft. "DB" connector, 2 m / 6.5 ft.
545307 3-lead cable, 1.2 m/4 ft. Disposable probes Cables for integrated reusable sensors
545302 3-lead cable, 3 m/10 ft 165640 Extension cable for disposable OXY-C1 Interconnect cable with "DB"
545308 5-lead cable, 1.2 m/4 ft. temperature probes, 1.3 m/4.3 connector, 1.5 m/5 ft.
545303 5-lead cable, 3 m/10 ft. ft. OXY-C3 Interconnect cable with "DB"
Lead sets, AAMI color coding 165641 Extension cable for disposable connector, 3 m/10 ft.
545317 3-lead set, clip, 0.75 m/30 in. temperature probes, 2.8 m/9 ft. OXY-C7 Interconnect cable with "DB"
8001958 3-lead set, clip, 1.5 m/60 in 8001642 Skin temperature probe for connector, 7 m/23 ft.
8001959 5-lead set, clip, 1.5 m/60 in. adult and infants Interconnect cable for use with universal
545318 5-lead set, clip, 1.25 m/49 8001643 Central temperature probe 12 F connector and adhesive sensors
in.(leg) and 75 cm/30 in.(chest) 8001644 Central temperature probe 9 F OXY-SL3 Cable, 3 m/10 ft.
545327 3-lead set, snap, 0.75 m/30 in. 8002910 Esophageal stetoscope with Universal sensors (OXY-SL3 cable
545328 5-lead set, snap, 1.25 m/49 in. temperature probe 9 F required)
(leg) and 75 cm/30 in.(chest 8002911 Esophageal stetoscope with OXY-F-UN OxyTip+ Finger, 1 m/3.3 ft.
Electrodes temperature probe 12 F OXY-W-UN OxyTip+ Wrap, 1 m/3.3 ft.
– 57 –
OXY-SE-3 OxyTip+ Sensitive Skin, SensoNor 844 transducer
1 m/3.3 ft., 3/pkg
Pulse Oximetry, Nellcor (N-XNSAT) 16577 Disposable flushing kit for
Adhesive sensors (OXY-SL3 cable See the “User’s Reference Manual” for a SensoNor 840 transducer
required) list of approved sensors. 16579 Holder for 2x SensoNor 840 or
OXY-AP-10 OxyTip+ Adult/Pediatric, 844 transducers
10/pkg
NIBP 165700 Spectramed P10EZ-1,0.45 m/1.5
OXY-AP-25 OxyTip+ Adult/Pediatric, Latex-free reusable DURA-CUFSR ft.
25/pkg 2754E Large adult cuff, wine 16571 Disposable flushing kit for
OXY-AF-10 OxyTip+ AllFit, 10/pkg 2753E Adult cuff, navy blue Spectramed transducer P10EZ-1
2752E Small adult cuff, navy blue M1002525 Biotrans interference
Pulse Oximetry, Enhanced (N-XOSAT) 2751E Child cuff, green cable
Integrated reusable sensors 2750E Infant cuff, orange 54586 Adapter cable for DTX
TM
R
OXY-F4-H OxyTip+ Finger, 4 m/13 ft. DisposableSOFT-CUFS disposable pressure
OXY-W4-H OxyTip+ Wrap, 4 m/13 ft. 2753 Infant cuff #3, white,20/pkg transducers, 3.8 m/12 ft
OXY-E4-H OxyTip+ Ear Sensor with 2754 Infant cuff #4,white, 20/pkg 875408 Cable for HP 1290C-type
"H" connector. 2755 Infant cuff #5, white,20/pkg pressure transducers, 30 cm/1 ft.
Integrated reusable sensors (OXY-SL3 Cuff hoses M1002423 Biotrans Base Plate
cable required) 895732 Adult hose, black, 1.8 m/6 ft. M1002427 Biotranssingle pressure kit
OXY-F-UN OxyTip+ Finger, 1 m/3.3 ft. 877235 Adult hose, black, 3 m/10 ft.
OXY-W-UN OxyTip+ Wrap, 1 m/3.3 ft. 879739 Adult hose, black, 6 m/20 ft. Accessory kits
OXY-SE-3 OxyTip+ Sensitive Skin, 877514 Infant hose, white, 3 m/10 ft. Hemo start up kit for Cardiocap 5
1 m/3.3 ft., 3/pkg 890639 Infant hose, white, 6 m/20 ft. Order Code: 8000086
Adhesive sensors (OXY-SL3 cable Plastic connectors Specification:
required) 646588 Plastic connectors for - 1 five-lead ECG trunk cable, AAMI color
OXY-AP-10 OxyTip+ Adult/Pediatric, upgrading adult NIBP cuffs and coding (545303)
10/pkg hoses - 1 five-lead set ECG, AAMI color coding
OXY-AP-25 OxyTip+ Adult/Pediatric, (545318)
25/pkg
Invasive Blood Pressure
Reusable transducers and cables - 1 adult NIBP hose (877235)
OXY-AF-10 OxyTip+ AllFit, 10/pkg R
- 1 adult DURA-CUF (2753E)
Interconnect cable for use with universal 78000 SensoNor 844, 3 m/10 ft.
78002 Disposable dome for SensoNor - 1 adult skin temperature probe (16560)
connector and adhesive sensors
844 transucer - 1 OXY-C3 interconnect cable, 3 m/10 ft.
Interconnect cable with "H" connector, 3
16578 Disposable dome for SensoNor (OXY-C3)
m / 10 ft
844 transucer - 1 OXY-F-DB interconnect sensor, 2 m/6.5
78001 Disposable flushing kit for ft. (OXY-F-DB)
– 58 –
Hemo start up kit for Cardiocap 5 Order Code: Disposable airway adapters
Order Code: 897608 73385 Straight T-adapter, 10/pkg
8000087 Specification: 73386 Elbow adapter, 10/pkg
- 5 disposable CO2 sampling lines Filtration
Specification:
(733163) 70605 Bacterial/viral removal
- 1 five-lead ECG trunk cable, IEC color
- 1 D-fend+ water trap, green (881319) Y-filter/S, 35/pkg
coding (545301)
- 1 five-lead set ECG, IEC color coding - 2 spirometry tubes (884101) Calibration gases
(545316) - 2 reusable D-lite sensors (733910) 755583 (For outside North America;
- 1 adult NIBP hose (877235) Flushing kits must use with regulator 755533)
- 1 adult DURA-CUFR (2753E) 16577 Disposable, for transducer Quick Cal calibration gas
SensoNor 840, sterile, 10 kits (CO2, N2O, O2, Des)
- 1 adult skin temperature probe (16560)
16578 Disposable, dome for transducer 755533 Regulator for 755583
- 1 OXY-C3 interconnect cable, 3 m/10 ft.
(OXY-C3) SensoNor 840, sterile, 50/pkg 755571 (For North America; must use
with regulator 75553-01)
- 1 OXY-F-DB interconnect sensor, 2 m/6.5
ft. (OXY-F-DB) Airway Gases Quick Cal calibration gas
Anesthesia gas sampling lines (CO2, N2O, O2, Des)
Includes ECG cables with AAMI color
73319 Disposable, 3 m/10 ft., 10/pkg 75553-01 Regulator for 755571
coding
CO2 sampling lines Gas return and scavenging
Start-up kit gas, anesthesia for Cardiocap 5 881644 Adapter for gas return, 5/pkg
733163 Disposable, 3 m/10 ft., 10/pkg
Order Code: 733195 Sample exhaust line for gas
D-fend water traps
897609 return or scavenging,
876446 D-fend, black, 10/pkg
Specification: disposable, 5/pkg
881319 D-fend+, green, 10/pkg
- 5 disposable anesthesia gas sampling 876107 Container, 5/pkg Patient Spirometry
lines (73319)
Adapters for low dead-space pediatric Sensors:
- 1 D-fend water trap, black (876445)
endotracheal tubes: 733910 Reusable D-lite sensor
- 2 spirometry tubes (884101)
877583 ID 2.5 mm, 5/pkg 73393 Reusable Pedi-lite sensor
- 2 reusable D-lite sensors 733950 Single use D-lite sensors, 50/pkg
877584 ID 3 mm, 5/pkg
(733910)http://supplies.datex- Disposable spirometry tubes
877585 ID 3.5 mm, 5/pkg
ohmeda.com/ACCProductSet.asp?ID=99& 884101 3 m/10 ft., yellow, 5/pkg
title=99,24,1 - s 877586 ID 4 mm, 5/pkg
Disposable spirometry accessory kit
Reusable airway adapters 889560 50 kits
Stat-up kit gas, critical care Cardiocap 5
84995 Steel adapter, 15F-15M
– 59 –
572238 Portable monitor wall mount machines (requires 1009-3262-000 long
NMT folding display mount)
572235 Portable monitor roll stand
888417 Regional block adapter,
891844 Remote Control holder 1009-3262-000
0.5 m/1.5 ft.
Long folding display mount (for
57268 Electrodes, solid gel, 30/pkg Mounting Solution for Aestiva Anesthesia
upgrading existing Aespire machines with
871251 NMT simulator Machine short folding display arm to add 1009-
891192 Bed sheet clip, 3/pkg 1006-8070-000 Factory-installed left hand 3265-000 Cardiocap/5 mounting bracket)
NMT sensors (cable required) display arm mount
888418 MechanoSensor, 0.3 m/1 ft. 1006-8071-000 Factory-installed right hand Upgrade Products for Cardiocap/5
display arm mount K-CREMCO Remote Control
897439 MechanoSensor, pediatric,
0.3 m/1 ft. 1006-8072-000 Factory-installed folding U-XDNET U-XDNET Data card and
arm mount Network upgrade, English
888416 ElectroSensor, 0.3 m/1 ft.
1006-8067-000 Field upgrade display arm U-XDNET U-XDNET Data card and
Cables for NMT sensors mount
888415 Cable, 1.5 m/5 ft. Network upgrade, French
1006-8068-000 Field upgrade folding arm U-XDNET U-XDNET Data card and
888414 Cable, 3.3 m/11 ft. mount Network upgrade, German
Other Monitor Supplies Mounting Solution for Excel 210 and U-XNET U-XNET Network upgrade
M1022178Dust filter for Cardiocap/5 Modulus I
For more information, see the Supplies
74205 Thermal recorder paper, 1001-3482-000 Dovetail 38 cm/15 in. arm and Accessories Catalog.
20 rolls mounting kit, 36 kg/80 lb.
Patient accessories designed for use with
85969 Cleaning fluid weight kit
this device are made of biocompatible
887045 Datex-Ohmeda Data card, 1004-3943-000 Dovetail 38 cm/15 in. arm materials conforming to requirements of
Eng/Ger mounting kit 18 kg/40 lb. EN 30993 Biological Evaluation of Medical
887047 Datex-Ohmeda Data card, Fra weight kit Devices. Therefore, they do not contain
Mounting Solution for S/5 Aespire toxic ingredients or primary skin irritants.
Fuses
Anesthesia Machine The conformity is based either on
511200 T2AH/250V, 5x20 mm
1009-8168-000: laboratory testing or material knowledge
Interface cables Factory installed monitor mount (includes and the long history of the used materials.
894193 Printer cable 1009-3265-000 and 1009-8167-000 folding
883857 PC-interface cable display mount)
1009-3265-000:
Mounting Elements
Mounting bracket for existing Aespire
572239 Wall mount
– 60 –