Beruflich Dokumente
Kultur Dokumente
MS39/MS39C/MS39SR/MS39U/MS39R
Configuration Introduction
Main Chip Introduction …………………………………………………………….……..3
Configuration Introduction……………………………………………………………….6
Interface Introduction………………………………………………………….……........11
Key Components Introduction ………………………………………….………….…..16
Key Components List………………………………………………………………..……….21
Block Diagram…………………………………………………………………………………..23
Signal Flow Diagram……………………………………………………………….…………24
Block Diagram of I²C Bus Controlling………………………………………………….27
Power supply network……………………………………………………………………….28
Key test point………………………………………………………………….………..........31
Unit Circuit Analysis and Testing ……………………………………………….………45
Pin Diagram of U801………………………………………………………………………….49
PWM wave form and Power on Sequences……………………………………….54
Trouble Shooting……………………………………………………………………...……….57
Enter factory menu method ………………………………………………………….....65
Software update from USB and system reset method…………………………66
Introduction of MHL…………………………………………………………………………..57
2
Main Chip Introduction
MSD3393LB is a highly integrated TV SoC solution for ATSC digital television
platform. Integrating latest advanced technologies from Mstar Semiconductor,
the world leading TV SoC provider in TV industry, MSD3393LB provides the most
cost-efficient solution for multimedia TV application with creative and attractive
features exclusively presented.
3
Main Chip Introduction
The powerful multimedia A/V decoder inside MSD3393LB is hosted with a
dedicated hardware video codec engine to secure fast and stable video streaming
playback. Moreover, MSD3393LB is equipped with a DSP specifically designated
for audio application, including digital audio format decoding and advanced sound
effects, and a high performance RISC CPU to manipulate all possible routines and
house-keeping activities. With extendable USB2.0 interface, an MSD3393LB based
system can turn into a high quality media-center in a simple manner.
5
Configuration Introduction
Main Board Power Board Light bar wires
6
Configuration Introduction
Power Board Driver Board LVDS cable Main Board
7
Configuration Introduction
Main Board FFC cable Power Board
IR Right
AC IN left speaker
Board speaker
9
Configuration Introduction
Power Board FFC cable Main Board
KEY Right IR
AC IN left speaker
Board speaker Board
10
Interfaces Introduction(MS39C)
P502,P503 P102 to
to speaker P101 P601 to Source IR BD
TO PSU of panel
P103 to
Key BD
P203
P301 P501 P201 P202 P204 P304 P304 P304 TUN2
HDMI 2
USB Earphone HDMI 3 HDMI 1 VGA R L SPDIF TUNER
/MHL
P301
USB
P202
HDMI 1
P203
HDMI 2
/MHL
P201
HDMI 3
P306 P304 P304 P304 P304 P304 P204 P300 TUN2 P501
SPDIF Pr Pb Y/AV R L VGA VGA TUNER Earphone
12
Interfaces Introduction(MS39SR)
P304 P101 P601 to Source
YPbPr TO PSU of panel
P102 to
Key /IR
BD
P502,P503
to speaker
P203
HDMI 1
P203
HDMI 2
/MHL
P301
USB
14
Interfaces Introduction(MS39R)
P304 P306 P300 P101 P602 to Source
YPbPr SPDIF VGA Audio TO PSU of panel
P301
USB
P202
HDMI 1
15
Key Components Introduction(MS39C)
U501 UD6 U174 U700 X801
Audio amplifier 12V-5V 5V-1.8V Flash IC 24M Crystal
16
Key Components Introduction(MS39)
U501 UD6 U174 U700 X801
Audio amplifier 12V-5V 5V-1.8V Flash IC 24M Crystal
17
Key Components Introduction(MS39SR)
U301 UD6 U700 U174 X801 U501
USB 5V Switch 12V-5V Flash IC 5V-1.8V 24M Crystal Audio amplifier
19
Key Components Introduction(MS39R)
U501 UD5 U700 X801 U174
Audio amplifier 3V3SB/5V-1.2V Flash IC 24M Crystal 5V-1.8V
/ / 13-RT9711-AGBG / / U301
21
List of Key differences
22
Block Diagram
LVDS FLASH
(U501)
HDMI1 IR、KEY
HDMI2/MHL
HDMI3
SPEAKERS
U801 Amplifier
MSD3393LB-S7 STA381BW
YPbPr/AV
(U501)
Audio
VGA
Earphone
USB
TUNER SPDIF
23
Signal Flow Diagram(MS39C)
24
Signal Flow Diagram(MS39)
25
Signal Flow Diagram(MS39SR)
26
Block Diagram of I²C Bus Controlling
27
Power Supply Network(MS39C)
28
Power Supply Network(MS39)
29
Power Supply Network(MS39SR)
30
The Key Test Points of 3V3SB(MS39C)
Q712 PinE:
P101 3V3SB U700 Pin7:
Pin7/8: 3V3SB 3V3SB
Pin5/6: POWER-ON/OFF
P102 Pin1:
3V3SB
P103 Pin1:
3V3SB
D111
3V3SB
31
The Key Test Points of 3V3SB(MS39)
P103 Pin1: D111 U700 Pin7:
P101 3V3SB 3V3SB 3V3SB
Pin7: 3V3SB
Pin10: POWER-ON/OFF
P102 Pin1:
3V3SB
Q712 PinE:
3V3SB
32
The Key Test Points of Power Supply on M.D(MS39C)
33
The Key Test Points of Power Supply on M.D(MS39)
UD6 U174 Q601
12V-5V 5V-1.8V PANEL_VCC
34
The Key Test Points of DC-DC (24V to 12V MS39)
LD4
12V output
35
The Key Test Points of DC-DC (24/12V to 5V)
LD6
5V output
LD6
5V
output
36
The Key Test Points of DC-DC (5V/3V3SB to 1V2)
LD1
VDDC output
LD1
VDDC output
37
The Key Test Points of LDO (5V to 3V3)
U172
3V3 output
U172
3V3 output
38
The Key Test Points of LDO (5V to 1V8D)
U174
1V8D output
U174
1V8D output
39
The Key Test Points of Backlight ON/OFF
R104 P101 PIN12 P101 PIN3/4 R104
BL_ON BL_ON BL_ON BL_ON
MS39 MS39C
40
The Key Test Points of Dimming Circuit
P101 PIN11 P101 PIN8 P101 PIN1/2
DIM_PWM DIM_DC DIM_PWM
R105
DIM_PWM
R105
DIM_PWM R101
DIM_DC
MS39 MS39C
41
The Key Test Points of Tuner
TUN_IFP
AGC
TUN_IFN
TUN_SDA
TUN_SCL
MS39
TUN_VCC TUN_VCC MS39C
3V3 3V3
42
The Key Test Points of Power Amplifier
C551
Supply: MS39 24V
MS39SR 12V
L551
3V3A
L552
3V3D
43
The Key Test Points of IR and Key Board
P102
Pin2: IR
Pin1: 3V3SB
44
Unit Circuit Analysis and Testing(Tuner)
IIC
If the you run the channel scan and can find none channel,
do as below
1. Check signal from the cable, is there any signal?
2. Check the power supply for the Tuner, is it normal?
3. Check IIC of the tuner, is it normal?
4. Check VIFN_IN/VIFP_IN, are there any signal?
5. Check the software or update it
45
Unit Circuit Analysis and Testing(Reset circuit)
R714
MCU_RESET
R714
MCU_RESET
MS39 MS39C
46
Unit Circuit Analysis and Testing(Reset circuit)
charge
Power test
point
charge
When the main Power 24/12V gets lower than 17.8V/8.3V , the voltage of Q712’s PIN B will lower than
2.6V, while the voltage of PIN E is 3.3V, then Q712 will turn on, the voltage of MCU_RESET is high, TV
reset. As the same reason, when the main Power is turned off, Q712 turns on , TV reset.
47
Unit Circuit Analysis and Testing(PANEL_VCC)
If there are no picture on the screen
Q601 PIN D
PANEL_VCC
but the backlight is on, check the
below circuit.
When the PANEL_ON/OFF is high
level, Q602 will turn on, then the
Q601 will turn on. If PANEL_ON is
high level but no power for the
PANEL_VCC ,check Q602 and Q601,
MS39 whether they OK, if not, replace
them.
Q601 PIN D
PANEL_VCC
MS39C
48
Pin Diagram of U801(HDMI Interface)
49
Pin Diagram of U801(LVDS Interface)
U801
50
Pin Diagram of U200(Video/Audio)
VGA
U801
CMPT
AV
Audio_In
51
Pin Diagram of U200(FLASH/IIC/IIS/USB/IO)
IIS
USB
U801
IIC
IO
U801
FLASH
52
Pin Diagram of U801(TV Interface)
53
Waveform (backlight 80) as below
DIM_PWM
54
Power on Sequences
AC
Supply
3.3V Supply
U801 Reset
Panel On/OFF
T-Con.
Backlight On
55
Software
U700, to store main software, to control U801 to turn on TV and standby, to control source
switching and channel changing and all remote control functions.
56
Trouble Shooting
No Working
Main software in
Is 1.2V, 1.8V, 3.3V, U801 Problem U700 is abnormal
3V3SB for U801 OK? Yes
Yes
57
DC-DC of 24V/12V to 5V
B
The DCDC UD6 is just like a switch with a very high frequency. The Caps in point A are for
filter and keeping the current . The output in point B is a PWM waveform, because the
current can’t change from a certain value to zero immediately, so there must be a diode
DD3. Using a LC filter (LD6 and the Cap)we change the PWM into a certain voltage. And
the duty ratio is a key parameter.
Vout=PWM duty ratio * Vin
The PWM duty ratio is determined by the voltage of point C, and point C is also a feedback
circuit .
58
Waveform of I²C Bus Line as below
59
Trouble Shooting(Picture)
Abnormal Picture
Check peripheral
components of U801
60
Trouble Shooting(Sound)
Abnormal Sound or No Sound
Abnormal sound in To check which source has Abnormal sound in all source
some of source abnormal sound
N
Check the power supply of Check the
U501,is it OK? power circuit
Check is there audio Y
signal send to U501? Y
Check the waveform of out- Check
1A,1B,2A,2B of U501, are they OK? Speakers
N Replace
Is U801 OK?
U801 Check the waveform of
Y Pin37,38,39,41 is ok? Check
the work
N Y
conditions of
Check the coupling Upgrade S/W of U501
circuit U700
U801 NG
Y
Replace
Replace U801 U501
61
Amplifier process
S
P
E
K
E
R
U801
62
Function View (U501)
63
Headphone
64
Enter Factory menu method:
Follow the below steps to pop-up the Factory Menu in case of “FactoryKey” is
disable:
press Remote Control key “MENU” to display main menu
Select “Picture” and press “OK” or “LEFT” key to enter the picture submenu
Select the “Contrast” item
Press the subsequence Remote Control keys “9”, “7”, “3” and “5” to enter
the Factory menu.
Press Remote Control key “Return” To pop-up the Factory Menu in case of
“FactoryKey” is enable.
The status of “Factory Key” can be changed in Factory Menu->FAC_HOTKEY
Press Remote Control “OK” key or “RIGHT” key to enter the submenu.
Press Remote Control “Menu” key to go back to the root menu.
Press Remote Control “RIGHT” or “LEFT” key to change the values.
Press Remote Control “RIGHT” or “OK” key to run the function.
Press Remote Control “Exit” key exit the factorymenu.
65
Software update from USB(TV on)
1) You need get a update file like: “MERGE.bin”
2)Directly copy this “MERGE.bin” file into the root directory of USB
disk.
3) Insert USB to TV, enter the factory menu and select the USB_UPADT
item, then select “YES”, the TV will update automatically and restart
66
Software update from USB(TV off)
1. You need get a update file like: “MERGE.bin”
2. Directly copy this “MERGE.bin” file into the root directory of USB
disk.
3. Insert USB to TV, press the “POWER” button on the KEY board
which on the left side of the TV set.(Do not remove your hand,
pressing it)
4. Plug the TV plug into a plug seat, continue pressing the button for
at less 20 seconds.
5. Remove your hand the TV will automatically update and then reset.
67
System reset method
68
Introduction of MHL
69
Introduction of MHL
70
Introduction of MHL
Go to www.mhlconsortium.org/ to see the list of devices which support the
MHL.
Using the CBUS of the MHL, you can use the TV Remote to control your
cellphone or other devices . If you can not control the devices by Remote
control, maybe your devices don’t support this function.
1. Menu button
2. 4 Direction buttons
3. OK or Enter button
4. GOBACK or Exit button
71
Introduction of MHL
72
THANK YOU