Beruflich Dokumente
Kultur Dokumente
SECTION 5
Structures and supports
Introduction The structure and support products in this Section 5 include Page 5/1
galvanised mild steel fabricated components that enable the
rapid assembly of a complete outdoor substation switchyard.
The components are designed to suit the substation’s
particular requirements.
Equipment stands are dimensioned to suit the particular type
and model of equipment required to be supported.
Note Our offer does not include for fitting or assembly on site.
5/1
Bus supports – general arrangements
All our structures and supports designs are to New Zealand seismic and structural
strength standards with type design studies and approvals by our consultant
structural engineers.
We are able to provide designs covering a variety of substation voltages, equipment
types, and switchyard arrangements.
SECTION 5 Contact us with your project details and we shall provide you with an offer to suit
your requirements.
Structures and supports
5/2
Cable stands – general arrangements
All our structures and supports designs are to New Zealand seismic and structural
strength standards with type design studies and approvals by our consultant
structural engineers.
We are able to provide designs covering a variety of substation voltages, equipment
types, and switchyard arrangements.
SECTION 5 Contact us with your project details and we shall provide you with an offer to suit
your requirements.
Structures and supports
5/3
Cable stands – general arrangements
All our structures and supports designs are to New Zealand seismic and structural
strength standards with type design studies and approvals by our consultant
structural engineers.
We are able to provide designs covering a variety of substation voltages, equipment
types, and switchyard arrangements.
SECTION 5 Contact us with your project details and we shall provide you with an offer to suit
your requirements.
Structures and supports
5/4
Circuit breaker and recloser stands –
general arrangements
All our structures and supports designs are to New Zealand seismic and structural strength
standards with type design studies and approvals by our consultant structural engineers.
We are able to provide designs covering a variety of substation voltages, equipment types,
SECTION 5 and switchyard arrangements.
Contact us with your project details and we shall provide you with an offer to suit
Structures and supports your requirements.
5/5
Disconnector stands –
general arrangements
All our structures and supports designs are to New Zealand seismic and structural strength
standards with type design studies and approvals by our consultant structural engineers.
We are able to provide designs covering a variety of substation voltages, equipment types,
SECTION 5 and switchyard arrangements.
Contact us with your project details and we shall provide you with an offer to suit
Structures and supports your requirements.
5/6
Measurement transformer
(CT and VT) stands
All our structures and supports designs are to New Zealand seismic and structural strength
standards with type design studies and approvals by our consultant structural engineers.
We are able to provide designs covering a variety of substation voltages, equipment types,
SECTION 5 and switchyard arrangements.
Contact us with your project details and we shall provide you with an offer to suit
Structures and supports your requirements.
5/7
Bearers and bearer supports
All our structures and supports designs are to New Zealand seismic and structural
strength standards with type design studies and approvals by our consultant
structural engineers.
We are able to provide designs covering a variety of substation voltages, equipment
types, and switchyard arrangements.
SECTION 5 Contact us with your project details and we shall provide you with an offer to suit
your requirements.
Structures and supports
Series ST supports
The Series ST support units are manufactured from hot dip galvanised mild steel sections. They are used
for supporting bearers on one or two poles. Primarily for mounting disconnectors, but also for mounting
ancillary equipment e.g. Busbar support insulators, CTs, etc.
Series ref A B C D E F G H
ST-
ST-
Series SU bearers
The Series SU bearer units are manufactured from mild steel channels which are hot dip galvanised after
all drilling is completed. They are typically used for mounting our 33kV disconnectors. Similar bearers may
be used for switchgear, up to 110kV as well as for busbar supports and ancillary equipment.
Please contact us with your project requirements.
SU-
SU-
5/8