Sie sind auf Seite 1von 4

www.5starnotes.

com

om
ANNA UNIVERSITY, CHENNAI 25

MODEL QUESTION PAPER

B.E. AERONAUTICAL ENGINEERING, , V SEMESTER

.c
AE341 - AIRCRAFT STRUCTURES - II

TIME – 3 Hours MAXIMUM : 100 Marks

es
PART A (10 X 2 = 20 Marks)
ANSWER ALL QUESTIONS

ot
1. Define shear centre
2. Give a sketch of a thin-walled angle section and mark the shear centre location for
the same.
rn
3. State S.I. Units for (a) shear flow, (b) shear modulus
4. State the Bredt - Batho formula and list the assumptions involved.
5. A thin - walled single - cell tube is subject to torsion. Derive an expression for shear
plow in the walls of the tube.
ta

6. Briefly write about the concept of lumping of cross - sections.


7. For a structure which carries primarily bending loads?
why are I - sections preferred over other cross-sections?
5s

8. What is a wagner beam?


9. What are monocoque structures?
10. List 2 functions of an aircraft rib.
w.

PART B (5 X 16 = 80 Marks)
ww

11. (i) Bring out the differences between


Symmetrical and unsymmetrical bending 4

(ii) What are principal axes of inertia? 2

(iii) A bending moment of 3000 Nm is 10


applied to the cross - section shown in Figure 1
at an angle of 30 to the vertical y-axis such that
Mx and My both produce tension in the positive x-y quadrant.
Obtain the expression for bending stress.

www.5starnotes.com
www.5starnotes.com

om
.c
es
ot
rn
Figure 1

12(a) For the section shown in Figure 2(a), determine the shear centre location. 16
ta
5s
w.

Figure 2(a)

12(b) A vertical load of 1000N is applied to the Section indicated in Figure 2(b) in the
positive - y direction. Plot the shear flow distribution. 16
ww

Figure 2(b)

www.5starnotes.com
www.5starnotes.com

om
13(a) The section shown in Figure 3(a) is subject to forces Fx = - 1600 N and Fy = 6000 N.
Determine the bending stresses at the stringer locations A, B, C, D. Assume that the
webs are ineffective in bending. 16

.c
es
13(b) (i)

ot
A thin-walled tube having a cross-sectional area `A' and wall thickness `t', is
subject to twisting moment Mo. Derive and obtain the expression
for cell twist. 8
rn
(ii) The 2-cell tube indicated in Figure 3(b) is subject to a clockwise
twisting moment of 1000 Ncm. Determine the shear flows
in the walls of the tube. 8
ta
5s
w.

All other wall thickness = 1 mm

Figure 3(b)
ww

14(a) Write notes on the following


(i) the strength of thin-walled columns, 6
(ii) the concept of `EFFECTIVE SHEET WIDTH', 6
(iii) inter-rivet and sheet wrinkling failures 4

14(b) (i) Derive the bucking equation for a thin plate 10


(ii) Explain the interaction relationship and state its uses 6

www.5starnotes.com
www.5starnotes.com

om
15(a) (i) Discuss the analysis of a semi-cantilever type of 8
aorcraft womg

(ii) List out the different structural elements contained in an aircraft

.c
wing. What are their functions? 8

or

es
15(b) The tapered beam shown in figure 4(a) is subject to a vertical load V

(i) Derive an expression for shear flow at any point in the


web of the beam. 8

ot
(ii) Obtain the shear flow distribution when V = 10,000 N 8
rn
ta
5s
w.
ww

www.5starnotes.com

Das könnte Ihnen auch gefallen