Beruflich Dokumente
Kultur Dokumente
13 3
16
6
15
9
10
1
5
11 12
14
2
217327
Main components
1 Pump suction strainer: 100-mesh metal strainer 5 Oil line to lift cylinder:
2 Hydraulic pump (gear pump): FC trucks have a flow regulator valve in a down-
A regular gear pump is directly coupled to the en- stream section of this line. This line also has a hy-
gine PTO. See the "Hydraulic Pump" section for de- draulic pressure sensor.
tails. 6 Tilt cylinder
3 Hydraulic pump delivery hose: 7 Piping to tilt cylinder
The shape of this hose for the models is different 8 Steering valve
from that of the gasoline engine models, as the hy- 9 Oil feed line to steering valve P port:
draulic pump locations of these two models are dif- This line constitutes a part of the PF flow passage.
ferent. 10 Return oil line from steering valve
4 Hydraulic control valve: 11 Oil line to steering cylinder
MC valve is installed as the standard valve. FC 12 Steering cylinder
valve is available as an option. The MC valve has a 13 Return line
built-in flow regulator valve. but the FC valve does 14 Return filter:
not have a flow regulator valve. Both MC and FC This cartridge-type filter should be replaced at every
models take almost the same piping arrangement. oil change.
For more details, refer to "2.5 Piping." 15 Level gauge
16 Oil cap
11-1
HYDRAULIC SYSTEM
T P STEERING CYLINDER
T2 P
PF
A1
LIFT CYLINDER
P WITH DOWN SAFETY
Engine
GEAR PUMP
B2
A2
STANDARD
MC CONTROL VALVE TILT CYLINDER
B3
A3
T1
SUCTION RETURN
STRAINER FILTER
217137
11-2
HYDRAULIC SYSTEM
FC HYDRAULIC CIRCUIT
STEERING VALVE
L R
T P STEERING CYLINDER
T2 PF P
c1
LIFT CYLINDER
WITH DOWN SAFETY
P Pp
Engine
GEAR
PUMP a1 b1
A1
FLOW
REGULATOR VALVE
FC CONTROL
VALVE
a2 b2 A2
B2
STANDARD
TILT CYLINDER
T
a3 T1 b3 A3
SUCTION RETURN B3
STRAINER FILTER
217138
11-3
HYDRAULIC SYSTEM
(c) 1
5
9
(b)
8
7
(a)
10
6
11
213800
Main Components
1 Hydraulic tank 5 Tank cover 6 Suction strainer
2 Cap Parts welded to tank cover 7 Return filter
3 Element 8 Hydraulic pump
(a) Suction pipe
4 Level gauge 9 Pump suction line
(b) Pipe for return line 10 Pump delivery line
(c) Pipe for level gauge 11 Drain plug
The hydraulic tank is located in the middle of the right Return filter 7 is attached to the end of return pipe (b).
side of the frame and becomes a part of the frame The return filter is a cartridge type of 15 µm with a
structure. built-in relief valve. When the filter is clogged, the relief
Three pipes (a) (b) and (c) are welded together to the valve activates to divert unfiltered oil into the tank.
tank cover 5. Suction strainer 6, return filter 7, level Periodic replacement is necessary. Oil filter replace-
gauge 4, and cap 2 are installed on the top of each of ment is recommended once a month after the pur-
the three pipes. chase of the lift truck or after conducting a major
overhaul that includes replacing parts.
Therefore, parts in the tank can be taken out as an
assembly if the tank cover is removed. The suction strainer 6 is 100 mesh screen gauze.
Filter replacement or strainer cleaning can easily be Clean the suction strainer at every oil replacement.
carried out once removing tank cover 5. On the models with a wet-type single disc clutch, the
Level gauge 4 is inserted in the level gauge pipe (c) return oil line is attached on the tank side.
where the opening is blocked by cap 2 that has an ele- The drain plug is installed at the bottom of the tank.
ment attached.
11-4
HYDRAULIC SYSTEM
4 13 12 9 6 3 11 10
1 7 5 8 2
Pump installed on engine
217139
11-5
HYDRAULIC SYSTEM
2 3 4
1
9
7
6
8
5
T2
PF T1
B2
A2
P A1
213802
11-6
HYDRAULIC SYSTEM
3
1
2
9 10
7 8
4
11
T1
PF
B2
T2
A2
5
6 A1
P
213803
11-7
HYDRAULIC SYSTEM
1.7 Flow Regulator Valve (for Trucks with FC Control Valve Only)
To From
lift cylinder lift cylinder
215233
The flow regulator valve is connected between the control valve and the lift cylinder. When the forks are lowered,
the valve regulates the oil flow as the load varies on the lift cylinder, thereby keeping the forks lowering speed con-
stant, irrespective of the load weight.
Broken area
The down safety valve is located at the bottom of the right lift cylinder. This valve is a safety valve which regulates
the flow of oil to prevent the fork from moving down too quickly if the piping between the lift cylinder and flow regula-
tor valve is broken; or if the flow of return oil from the lift cylinder becomes excessive due to a maladjusted regulator
valve or a fault of another component.
11-8
HYDRAULIC SYSTEM
3 1 2 7 6 5 4
14 15 16 17 8 9 10 11 12 13
217403
Main Components
1 Cylinder tube 4 Pipe (integrated with cylinder tube) 7 U-ring, Backup ring
2 Piston rod assembly 5 Cushion bearing 8 Bushing
3 Cylinder head 6 Check valve 9 Wiper ring
10 X-ring
Cylinder dimensions (the length and stroke of cylinder vary depending on lift height.)
Unit: mm (in.)
Rod diame- Cylinder inside Cylinder outside
Mast ter diameter diameter Cushion Presence of
Truck type Lift height
type stroke return pipe
(d) (ID) (OD)
3400 or less
35 (1.38) 45 (1.77) 52 (2.05) 23 (0.91) No
(133.9 or less)
Simplex
1 ton class 3500 or higher
35 (1.38) 45 (1.77) 52 (2.05) 23 (0.91) Yes
(137.8 or less)
Triplex - 35 (1.38) 45 (1.77) 52 (2.05) 23 (0.91) No
3400 or less
40 (1.57) 50 (1.97) 57 (2.24) 23 (0.91) No
(133.9 or less)
Simplex
2 ton class 3500 or higher
40 (1.57) 50 (1.97) 57 (2.24) 23 (0.91) Yes
(137.8 or less)
Triplex - 40 (1.57) 50 (1.97) 57 (2.24) 23 (0.91) No
3400 or less
45 (1.77) 55 (2.17) 63 (2.48) 23 (0.91) No
(133.9 or less)
Simplex
3 ton class 3500 or higher
45 (1.77) 55 (2.17) 63 (2.48) 23 (0.91) Yes
(137.8 or less)
Triplex - 45 (1.77) 55 (2.17) 63 (2.48) 23 (0.91) No
11-9
HYDRAULIC SYSTEM
Groove
Descent Outflow
5 Passage (b) 4
213808
Groove
Ascent Inflow
5 Passage (b) 4
213810
The above illustration shows an example of the follow- This action opens the (B) area, causing the passage
ing: (a) to open. Oil from the passage (a) and passage (b)
As the piston rod assembly descends, the oil flows which opens from the beginning flows in the piston
through the center of the piston and causes the cush- bottom, acting on the entire bottom surface of the pis-
ion bearing 5 to descend at the same time. The oil ton and pushing piston rod assembly 2 upward.
flowing in through the center of the piston activates the
cushion bearing.
11-10
HYDRAULIC SYSTEM
As the piston rod assembly ascends to the highest opens and discharges oil and air to pressure oil (inter-
possible position, the pressure of the oil and air nal drain). In the cylinder with a return pipe, this area is
entrapped between the rod and cylinder exceeds the connected to the hydraulic tank.
set pressure of the check valve. The check valve then
11-11
HYDRAULIC SYSTEM
4 5 9 2 1 6 3 7 8
Cushion stroke
21 mm (0.83 in.) 213812
Main Components
1 Cylinder tube 4 Holder 7 Check valve
2 Rod 5 Cylinder head 8 Spring
3 Piston 6 Cushion spool 9 Bleed valve
Action
Pressure oil first flows through the hollow area inside This cylinder is provided with a cushion mechanism
piston rod 2 and enters the first lift cylinder. Because which prevents the piston bottom from impulsively
the inside diameter of the first lift cylinder is larger than contacting the cylinder bottom during piston descent.
that of the second lift cylinder, the first lift cylinder (Refer to the illustration below.)
ascends first. The second lift cylinder starts to ascend Bleed valve 9 is a valve for bleeding air when the
after the first lift cylinder has completed ascent. hydraulic system is overhauled.
11-12
HYDRAULIC SYSTEM
Fig. 4:
Inflow
The illustration shows a condition immediately before
piston ascent. Oil which flows through the hollow area
in cushion spool 6 acts on check valve 7.
Fig. 5:
Initial stage of ascent 3 Piston
Pressure oil pushes check valve 7 to the right. Pres-
(Oil flows along this
sure oil flows along the plane of the check valve and
plane.)
flows to the underside of the piston.
Seat plane Shape of
The "triangular shape" of check valve 7 is designed to (When the piston check valve
increase the initial inflow volume. The piston starts to descends, this
ascend. Fig. 5 plane seats.) 7 Check valve
Fig. 6:
The illustration shows an example in which cushion
Inflow
spool 6 has left the cylinder bottom and is ascending.
Inflow
213814
11-13
HYDRAULIC SYSTEM
Inflow and
outflow
d ID OD
Main Components
1 Cylinder tube assembly 5 U-ring 9 Check valve
2 Piston rod assembly 6 Wiper ring 10 Stand tube
3 Cylinder head 7 Seal ring assembly
4 Bushing 8 Slide ring
Action
This cylinder, mounted on the center of the mast, acts In the descending stroke of the piston rod, cushion oil
first during the ascending stroke of the fork. in air chamber A is sucked in space B. The air cham-
The piston rod extends from the cylinder tube by pres- ber, stand tube, and check valve are related parts for
sure oil acting on the piston bottom. For prevention of cushioning action.
an impulsive approach of the piston and the cylinder Extra oil which leaks from around the piston and
head at the last stage of its ascent, cushion oil is enters space B returns from stand tube 10 to the cylin-
always filled in space B, between the cylinder tube and der bottom via check valve 9 at the last stage of cylin-
the piston rod. When the piston rod ascends, it der ascending.
ascends while pushing out cushion oil to air chamber
The stand tube always retains a certain amount of oil
A at its last stage. Thus, the last stage becomes
as cushion oil. A certain amount of cushioning oil must
smooth.
be filled in the overhauled cylinder.
Cylinder dimensions (The cylinder length and stroke vary depending on lift height)
Unit: mm (in.)
Cylinder inside Cylinder outside
Truck type Mast type Rod diameter
diameter diameter
1 ton class 55 (2.17) 70 (2.76) 82 (3.23)
Cylinders for the duplex mast and the tri-
2 ton class plex mast are of the same dimension and 55 (2.17) 75 (2.95) 86 (3.39)
same type.
3 ton class 65 (2.56) 85 (3.35) 97 (3.82)
11-14
HYDRAULIC SYSTEM
Tightening torque:
1 ton class: 400 ± 40 N·m (40.8 ± 4.1 kgf·m) [295 ± 30 lbf·ft]
2 ton class: 380 to 407 N·m (38.7 to 41.5 kgf·m) [280 to 300 lbf·ft]
3 ton class: 434 to 61 N·m (44.3 to 47.0 kgf·m) [320 to 340 lbf·ft]
16 11 12 17
2 6 10
5
3,4
1 7 8 9
14 13 14 15
Tightening torque:
1 ton class: 170 ± 15 N·m (17.3 ± 1.5 kgf·m) [125 ± 11 lbf·ft]
2, 3 ton class: Screw nut fully on do nut torque.
217157
Main Components
1 Bolt, Nut 6 Rod guide 10 O-ring 14 Guide ring
2 Tilt socket 7 Wiper ring 11 Piston rod assy 15 Snap ring
3 Inner ring 8 Nut ring 12 Coller 16 Cylinder assembly
4 Bearing 9 Back-up ring 13 Piston seal 17 Bushing
5 Grease nipple
Cylinder dimensions
Cylinder length and stroke vary depending on tilt
angles of forward and backward tilt.
Unit: mm (in.)
Cylinder Cylinder
Rod diam-
Truck type inside outside
eter
diameter diameter
1 ton class 25 (0.98) 63 (2.48) 73 (2.87)
2 ton class 30 (1.18) 70 (2.76) 82 (3.23)
3 ton class 35 (1.38) 80 (3.15) 93 (3.66)
11-15
HYDRAULIC SYSTEM
2
3
217140
Removal sequence
1 Pump delivery hose 3 Pump mounting bolt
2 Pump suction hose 4 Pump
Installation
To install, follow the removal sequence in reverse.
Also follow the instructions given below.
Apply grease to the spline of the pump shaft before
installation.
Insert the O-ring between the pump and engine PTO.
Perform test operation after installing the pump. Refer
to 2.1.2 test operation.
11-16
HYDRAULIC SYSTEM
7 1
3 *
*
*
* *
* *
2 4
3
*
*
Parts marked with are included in the seal kit.
8 Parts without
* mark are not individual supply items. 213818
Sequence
1 Rear cover, Bolt, Washer, Bushing 5 Drive gear
2 Front cover, Snap ring, Shaft seal, Bushing 6 Driven gear
3 Gasket, Gasket (shaped like 3) 7 Side plate
4 Side plate 8 Body
11-17
HYDRAULIC SYSTEM
213819
Reassembly
To reassemble, follow the disassembly sequence in
reverse. Also follow the instructions given below.
(1) Replace the seal kit parts with new ones.
(2) Completely remove oil or grease on the mating
surfaces of covers 1, 2 and body 8.
(3) Visually check all the parts for cleanliness and
apply hydraulic oil to the inside surface of the
body before reassembly.
(4) Apply grease to the lip of the shaft seal.
(5) Be careful not to cause damage to the lip of shaft
seal by spline edges of drive gear 5.
(6) Tighten the bolts evenly and progressively.
(7) The pump is assembled properly if the pipe
wrench fitted on the pump shaft can be turned
easily by hand.
Test operation
Perform test operation after installing the pump.
(1) Check that the oil amount in the hydraulic tank is
sufficient.
(2) Attach a pressure gauge to the pump delivery
hose.
Refer to "Main Relief Valve."
(3) Start the engine, adjust the adjusting screw of the
main relief valve in sequence from 0 to 18.1 MPa
(0 to 185 kgf/cm2), and check the temperature rise
of the pump body by touching it by hand. If the
temperature rise of the pump body is substantial
compared to the oil temperature rise, disassemble
again for checking.
(4) Set the relief valve to the specified pressure.
(5) Measure the lifting speed of the fork without a
load. If the speed is to the specified value, the
pump discharge volume is normal.
(6) Check that the fork operates normally by raising
and lowering it under load.
11-18
HYDRAULIC SYSTEM
3
4
5
217141
Removal sequence
1 Hose guard 4 Cylinder clamp (Cushion, Collar, Shim)
2 High-pressure hose 5 Lift cylinder, Bracket
3 Set bolt, Shim
11-19
HYDRAULIC SYSTEM
213822
213824
214083
11-20
HYDRAULIC SYSTEM
Installation
To install, follow the removal sequence in reverse.
Also follow the instructions given below.
(1) Extend and retract the lift cylinders several times
under no load condition to bleed air out of the cyl-
inder circuits and to make sure that the cylinders
move smoothly.
(2) Check the oil level in the hydraulic tank with an oil
level gauge. (Refer to the topics "Hydraulic Tank"
in the following section "Inspection and Adjust-
ment.")
(3) Check the lift height.
(4) After the lift cylinders or piston rods have been
replaced, check for difference in stroke between
the two cylinders. (Refer to "Chapter 12 MAST
AND FORKS.")
11-21
HYDRAULIC SYSTEM
3
1 213826
Removal sequence
1 Nut 4 Chain wheel support assembly
2 Lift bracket assembly 5 Second lift cylinder
3 First lift cylinder
213827
213828
11-22
HYDRAULIC SYSTEM
213829
213830
213824
11-23
HYDRAULIC SYSTEM
213831
Installation
To install, follow the removal sequence in reverse.
Also follow the instructions given below.
(1) Install chain wheel support assembly 4 parallel to
a line connecting the centers of chain anchor bolt
holes on first lift cylinder 3 to prevent chains from
twisting.
(2) Adjust the chain tensions.
Refer to "Chain Tension Inspection and Adjust-
Good Bad
ment of Section 12.2" of "Chapter 12 MAST AND
FORKS."
213832
(3) Extend and retract the lift cylinders several times
under no load condition to bleed air out of the cyl-
inder circuits and to make sure that the cylinders
move smoothly.
(4) After proper operation is confirmed, check the oil
level.
11-24
HYDRAULIC SYSTEM
217420
Sequence
1 Retainer 6 Check valve, O-ring
2 Wiper, Rod seal, Backup rings, O-ring 7 Wiper ring, Piston seal, Backup ring
3 Spacer 8 Piston rod
Remove parts 4 through 8 as assembly. 9 Cylinder tube
4 Circlip, Sleeve
5 Washer
Note: Replacement parts marked with an asterisk (*) are included in the seal kit.
11-25
HYDRAULIC SYSTEM
Reassembly
1 2 3* 4 5 6 7
217421
Note: Replacement parts marked with an asterisk (*) are included in the seal kit.
11-26
HYDRAULIC SYSTEM
217422
Sequence
1 Retainer 6 Spacer
2 Wiper ring, Rod seal, O-ring, Backup ring 7 Snap ring
Remove parts 3 through 10 as sub-assembly from part 8 Sleeve
11. 9 Piston rod
3 Backup ring, Piston seal, Wear ring 10 Bleed screw, Seal washer
4 Pison 11 Cylinder tube
5 Pull-in wire
Note: Replacement parts marked with an asterisk (*) are included in the seal kit.
11-27
HYDRAULIC SYSTEM
Reassembly
7 5 10 4 1
8* 6* 3* 2*
9 11
217423
Sequence
1 Retainer 6 Pull-in wire
2 Wire ring, Rod seal 7 Piston
3 Backup ring, O-ring 8 Backup ring, Piston seal, Wear ring
4 Piston rod 9 Sleeve, Snap ring
Install parts 1, 2, 3, 4, 5, 6, 7 to part 4. 10 Cylinder tube
5 Spacer 11 Seal washer, Bleed screw
Note: Replacement parts marked with an asterisk (*) are included in the seal kit.
11-28
HYDRAULIC SYSTEM
217424
Sequence
1 Retainer 4 Circlip, Washer, O-ring, Check valve
2 O-ring, Backup ring, Rod seal, Wiper 5 Piston rod, Piston
Remove parts 3 through 5 as sub-assembly from part 6. 6 Cylinder tube
3 Wear ring, Nylon ring, Piston seal
Note: Replacement parts marked with an asterisk (*) are included in the seal kit.
11-29
HYDRAULIC SYSTEM
Reassembly
11 10 2 3* 4 5
217425
Sequence
1 Piston rod, Piston 6 Nylon ring
7 Piston seal Install parts 12 through 15 to part 11.
Install parts 2 through 9 to part 1. 12 Rod seal
2 Check valve 8 Nylon ring
13 Wiper
3 O-ring 9 Wear ring
14 Backup ring
4 Washer 10 Cylinder tube
15 O-ring
5 Circlip 11 Retainer
Note: Replacement parts marked with an asterisk (*) are included in the seal kit.
11-30
HYDRAULIC SYSTEM
1 4
217142
Removal sequence
1 Tilt cylinder pin 3 Tilt cylinder pin
2 Hoses (2 pieces per one cylinder) 4 Tilt cylinder
Start by Installation
(1) Lower the forks to the bottom, and tilt the mast To install, follow the removal sequence in reverse.
fully forward. Also follow the instructions given below.
(2) Attach a lifting sling to the round holes, right and (1) After installing tilt cylinders, check the balance of
left, in the top cross-member of outer mast, and mast tilting angle. Adjust if necessary. Refer to
support the weight of the mast with a hoist. "Adjustment of Mast Tilt Angle of Section 6.7" in
"Chapter 12 MAST AND FORKS."
Suggestions for Removal
(1) Retracting piston rod
Remove tilt cylinder pin 1, and start the engine
and retract the piston rod fully. Stop the engine.
(2) Disconnecting hoses
Disconnect hoses 2 from the cylinder at the con-
nectors. Use a drip pan to catch oil flowing out of
the cylinder. Attach caps to the connectors of the
cylinder to protect the threads of the connectors
and to prevent oil from flowing out of the cylinder
when the cylinder is removed.
(3) Removing tilt cylinder
Remove tilt cylinder pin 3, and remove the cylin-
der.
11-31
HYDRAULIC SYSTEM
Tightening torque:
1 ton class: 400 ± 40 N·m (40.8 ± 4.1 kgf·m) [295 ± 30 lbf·ft]
2 ton class: 380 to 407 N·m (38.7 to 41.5 kgf·m) [280 to 300 lbf·ft]
3 ton class: 434 to 61 N·m (44.3 to 47.0 kgf·m) [320 to 340 lbf·ft]
16 11 12 17
2 6 10
5
3,4
1 7 8 9
14 13 14 15
Tightening torque:
1 ton class: 170 ± 15 N·m (17.3 ± 1.5 kgf·m) [125 ± 11 lbf·ft]
2, 3 ton class: Screw nut fully on do nut torque.
217157
First, disassemble into four main parts: I, II, III and IV as seen below. Then disassemble each of the four main parts
individually. .
I. Tilt socket sub-assembly (Consisting of the following parts, 1 thru 5.)
1 Bolt, Nut 3 Inner ring 5 Grease nipple
2 Tilt socket 4 Bearing
II. Guide bushing sub-assembly (Consisting of the following parts, 6 thru 10.)
6 Rod guide 8 Nut ring 10 O-ring
7 Wiper ring 9 Back-up ring
III. Piston rod sub-assembly (Consisting of the following parts, 11 thru 15.)
11 Piston rod assy 13 Piston seal 15 Snap ring
12 Coller 14 Guide ring
IV. Cylinder sub-assembly (Consisting of the following parts, 16 and 17.)
16 Cylinder assembly 17 Bushing
11-32
HYDRAULIC SYSTEM
213838
Inspections after Disassembly
(1) Cylinder tube
(a) Check the bore wall for wear, grooving, scratch
marks and rusting.
(b) Check the welds for cracks.
(2) Piston rod
(a) Check for surface flaws such as grooving,
scratch marks, rusting and wear.
The rod must be replaced if its threads show a
sign of stripping or any other damage.
(3) Rings and packings
(a) Check each ring and packing for damage or
distortion.
(b) Also check for deterioration due to aging.
Suggestions for Reassembly
To reassemble, follow the disassembly sequence in
reverse, paying attention to the following points.
(1) Carefully clean all parts to remove any foreign
particle.
(2) Reassemble the cylinder in the reverse sequence
of the disassembling, apply hydraulic oil to the
bore wall of the cylinder tube, and also to sealing
parts; O-rings, piston seals, dust seals and pack-
ings. Pay attention to the orientation of parts.
(3) When clamping the cylinder tube in the vise, be
213839
careful not to distort the tube.
(4) Install the piston seal as follows:
(a) Before fitting the piston seal, squeeze it by
hand five or six times to soften it.
(b) Hold the piston in a vise, taking care not to
damage any part of the piston. Apply a thin
coat of hydraulic oil to the seal. Fit a portion of
the seal to the groove, and push the other por-
tion into the groove as shown.
(5) Tighten the thread to the specified torque. Refer
to the previous page for the torque. 213840
11-33
HYDRAULIC SYSTEM
3
5
Me
as
ure
4
215234
Sequence
1 Lock nut 4 Piston, Pin, Washer, Spring, Valve
2 Plug, O-ring 5 Valve body
3 Spring
Reassembly
To reassemble, follow the disassembly sequence in
reverse.
11-34
HYDRAULIC SYSTEM
2.5 Piping
(For piping around the mast, refer to "Chapter 12 MAST AND FORKS.")
Tilt line
Tilt line MC control valve
Right-hand tilt cylinder Return line
(low pressure)
Return filter
Suction strainer
Left-hand tilt cylinder
217158
11-35
HYDRAULIC SYSTEM
Tightening torque:
29 ± 3 N·m
(2.96 ± 0.31 kgf·m)
[3.8 ± 4.8 lbf·ft] Tank cover
Level gauge
Inspection
(1) Clean the suction strainer.
(2) The return filter is a scheduled replacement part.
Replace it when changing oil. In case of a new
truck or carrying out an overhaul, replace it after
the first month.
Installation
To install, follow the removal sequence in reverse.
Also follow the instructions given below.
(1) Tighten the strainer and filter to the specified
torque.
(2) Securely install the pump suction hose, exercising
care to avoid sucking in air.
11-36
HYDRAULIC SYSTEM
217143
(a) How to read the chart (example) (3) Inspection of suction strainer
1 ton class: In the truck equipped with a TRIPLEX Check the suction strainer for damage and clog-
5.5 m (18 ft) mast maintain the oil level at "N" mark ging. Clean it if it is dirty.
on the level gauge with the mast lowered to the
bottom. In the case of 6.0 to 7.0 m (19.7 to 23 ft) (4) Inspection of return filter
masts,, maintain the level at "H" mark with the mast Check the return filter for damage. As this part
lowered to the bottom. needs periodic replacement, replace it when the
replacement interval is reached. Refer to
(b) Another general rules "Removal and Installation of Suction Strainer and
In any machine regardless of the mast-and-attach- Return Filter."
ment combination, the oil level should not be above
"H" mark on the level gauge when the mast is at
the bottom. In addition, the oil level must be 5 mm
(0.12 in.) from the bottom end of the gauge or
higher when the mast is at the top.
The oil level in the tank must not exceed the H level
when the mast, regardless of any combination of the
mast and attachment, is lowered .
11-37
HYDRAULIC SYSTEM
11-38
HYDRAULIC SYSTEM
11-39
HYDRAULIC SYSTEM
11-40
HYDRAULIC SYSTEM
4. Troubleshooting
Not enough oil in hydraulic tank Refill.
Oil viscosity improper Change upon referring to "Fuel and
Lubricant Specifications" on chapter
13 Service data 4.2 Fuel and Lubri-
cant Specifications.
Overload Check working conditions and, if over-
loaded, urge the operator to stay
within the load limit.
Hydraulic tank heats
excessively Local overheating of oil line due to a large Clean oil line.
restriction to flow
Relief valve adjustment improper Readjust pressure setting.
Pressure drop due to fatigued or broken Disassemble or replace and readjust
Hydraulic springs pressure.
tank
Gear pump worn Replace pump.
Outlet pipe or tube flattened, or restriction Repair or replace.
to flow
Shortage of oil due to a natural loss Replenish oil upon referring to "Fuel
and Lubricant Specifications" on chap-
ter 13 Service data 4.2 Fuel and Lubri-
cant Specifications.
Cylinders move too Oil leakage due to damaged oil line and Repair or replace.
slow seals
Oil viscosity too high Change upon referring to "Fuel and
Lubricant Specifications" on chapter
13 Service data 4.2 Fuel and Lubri-
cant Specifications.
Gear pump does not pump oil Check pump and piping; repair or
replace.
Cylinders move too
Oil leakage from oil line Check oil for level and condition; add
slow
or change oil.
Gear pump internally leaking Replace pump.
Poor pumping Replenish oil upon referring to "Fuel
and Lubricant Specifications" on chap-
ter 13 Service data 4.2 Fuel and Lubri-
cant Specifications.
Cavitation (1) Check suction pipe for any flat por-
Noisy tion or loose connection; retighten
or replace.
(2) Check shaft oil seal for airtight-
ness; replace pump.
(3) Check pump body for any outside
Gear pump interference; repair.
Pressure too high Replace pump. (Check to see if relief
valve setting is correct.)
Distortion or damage due to external Replace pump.
Pump case, drive strain or stress
gear or pump port (1) Check to see if return line is
flange damaged blocked or restricted.
(2) Check to see if pipe connections
have been externally strained or
stressed.
Oil oozes out through the oil seal Replace shaft seal.
Oil oozes out onto the drive shaft sliding Replace whole pump assembly.
surfaces
Oil leakage from pump
Loose bolts that secure the pump Retighten. Replace if needed.
Degraded performance of sealing inside Replace gasket.
pump
11-41
HYDRAULIC SYSTEM
11-42
HYDRAULIC SYSTEM
11-43
HYDRAULIC SYSTEM
5. Service Data
Truck type
Item
1 ton class 2 ton class 3 ton class
Forward tilt angle
degrees A 5°
(standard truck with simplex mast)
Backward tilt angle
degrees A 10° 9° 6°
(standard truck with simplex mast)
Lift cylinder descent amount (at rated load)
mm (in.)/
[Retracted length of rod, oil temperature at A 50 (2.0) or less
15 min
45°C (113°F)]
Tilt cylinder forward tilt amount (at rated load)
mm (in.)/
[Extended length of rod, oil temperature at A 20 (0.8) or less
15 min
45°C (113°F)]
MPa +0.5 +5 +72
Main relief valve setting A 18.1 0 (185 0) [2625 0 ]
(kgf/cm2) [psi]
+0.5 +0.5 +0.5
8.8 0 10.3 0 10.3
0
MPa +5 +5 +5
Steering system relief valve setting A (90 0 ) (105 0 ) (105 0 )
(kgf/cm2) [psi]
+72 +72 +72
[1276 0 ] [1494 0 ] [1494 0 ]
N·m
Tightening torque of return filter A 49 ± 9.8 (5.0 ± 1.0) [36 ± 7.2]
(kgf·m) [lbf·ft]
N·m
Tightening torque of suction strainer A 49 ± 9.8 (5.0 ± 1.0) [36 ± 7.2]
(kgf·m) [lbf·ft]
A: Standard value
11-44
HYDRAULIC SYSTEM
Unit: mm (in.)
Truck type
Item
1 ton class 2 ton class 3 ton class
[Piston] Inside diameter of cylinder tube 1 A 45 (1.77) 50 (1.97) 55 (2.17)
Diameter of piston rod 2 A 35 (1.38) 40 (1.57) 42 (1.65)
N·m 170 to 240 200 to 270 270 to 304
Tightening torque for retainer 3 (kgf·m) A (17.3 to 24.5) (20.4 to 27.5) (27.5 to 31.0)
[lbf·ft] [125 to 177] [148 to 199] [199 to 224]
cc
Amount of hydraulic oil 4 A 57 (3.48)
(cu.in.)
Second
cylinder for 2 1
simplex mast
and triplex
mast
3 4
217144
First
cylinder for 1
2
duplex mast
and triplex
mast
3 4
217145
A: Standard value
11-45
HYDRAULIC SYSTEM
Unit: mm (in.)
Truck type
Item
1 ton class 2 ton class 3 ton class
[Piston] Inside diameter of cylinder
A 45 (1.77) 50 (1.97)
tube 1
Diameter of piston rod 2 A 32 (1.26 35 (1.38) 40 (1.57)
N·m 170 to 240 200 to 270
Tightening torque for retainer 3 (kgf·m) A (17.3 to 24.5) (20.4 to 27.5)
[lbf·ft] [125 to 177] [148 to 199]
N·m
Bleed screw tightening torque 4 (kgf·m) A 4.5 to 5.0 (0.46 to 0.51) [3.32 to 3.69]
[lbf·ft]
Second
cylinder for
duplex mast 4 1 2
3
217162
5 2 3 4
1
7
217161
A: Standard value
11-46
HYDRAULIC SYSTEM
6. MC Control Valve
6.1 Structure and Operation
6.1.1 MC Control Valve
5
P : Pressure oil inflow port from pump 4 9
2 B2
8 A2
3 A1
P
213856
Main valves
1 Inlet cover section (with built-in priority valve) 6 End cover section (with built-in unload valve)
2 Lift valve (with built-in flow regulator valve) 7 Steering system relief valve
3 Tilt valve 8 Main relief valve
4 Attachment valve (1) 9 Unload valve (with solenoid)
5 Attachment valve (2)
The above illustration shows an external view of the returns, namely through the descent hydraulic circuit
four-valve type MC control valve. Any one of the two that has a built-in lock valve linked with the flow regu-
valve to five-valve type valves is installed on a truck lator valve and the seat switch.
depending on the lift truck specifications.
The most basic valve configuration is a two-valve type, Tilt valve 3 feeds and returns pressure oil to and from
combination of the lift and tilt. Adding attachment the tilt cylinder which tilts the mast forward or back-
valve(s) to this combination is three-valve type, four- ward. The tilt lock valve is assembled in the main
valve type or five-valve type valve. spool to ensure safety when the mast is tilted forward.
Inlet cover section 1 has a built-in priority valve. This Attachment valves 4 and 5 are direction control valves
valve is a flow divider valve which feeds a certain which feed pressure oil to actuators of the attach-
amount of the total inflow volume from the P port pref- ments.
erentially to the steering system and the extra flow vol-
ume to the cargo-handling valve.
In addition, the inlet cover section is provided with End cover section 6 is provided with unload valve 9.
main relief valve 8 and steering relief valve 7. This valve is linked with the seat switch, and is a sole-
noid valve which closes the parallel feeder (high-pres-
Each of these valves limits the maximum pressure to sure circuit) to hold pressure oil only when the seat
protect the system. switch is ON.
11-47
HYDRAULIC SYSTEM
1 Priority valve
2 Main relief valve 8
3 Steering system relief valve
4 Lift valve
5 Second valve (operates in conjunction with lift
lowering switch)
6 Tilt valve A3
7
7 Attachment valve
8 Unload Valve B3
9 Solenoid for unload valve
10 Center bypass port
A2
11 Parallel feeder B2 6
1
P T2
2
213857
11-48
HYDRAULIC SYSTEM
5 PF
7
6
Ball check seat surface 3 4 Passage of extra flow (EF flow) 213858
The inlet section of the control valve consists of the When the flow volume flowing in the port P from the
main relief valve 6, which limits the maximum pressure pump increases, PF flow passing the control orifice is
of the hydraulic system. The priority valve which feeds going to increase. Then, differential pressure before
the pressure oil preferentially to the steering system, and after the control orifice becomes greater.
and the steering system relief valve 7, which limits The left edge face of the valve spool 1 acts on the
maximum pressure of the supplied pressure oil. hydraulic pressure before the control orifice, namely
The priority valve is a flow divider valve which divides pump pressure, and on the right edge face of the spool
supplied oil to a predetermined volume of priority flow acts on the PF flow pressure.
(PF flow) and extra flow (EF flow). PF flow and EF flow Therefore, when differential pressure becomes
are supplied to the steering system and the cargo-han- greater, the valve moves to the right, closes the PF
dling valves, respectively. restricted area and opens the EF restricted area,
The above illustration shows the position of priority releasing extra flow to the EF port. As a result, PF flow
valve spool 1 during operation (during pump rotation). decreases and differential pressure also decreases.
The priority flow (PF flow) of pressure oil which flows On the other hand, when the flow volume of pressure
in the port P flows in the following sequence: PF oil flowing in the port P decreases, PF flow flowing
restricted area→Hole A→Control orifice →Groove through the control orifice decreases and differential
between ball check 3 and ball retainer 4→Spring pressure also decreases. The spool moves to the left
chamber →PF port. and restricts extra flow. As a result, PF flow increases
This passage is always open and a certain volume of and differential pressure also increases.
oil is flowing toward the steering valve during opera- Differential pressure varies between extra flow and PF
tion. flow not only by the flow volume but also by operation
Extra flow (EF flow) passes the EF restricted area, of the fork. Differential pressure before and after the
flows in the EF port and then, in the center bypass port control orifice, however, can be kept constant by
of the load-handling valve. adjusting angles of the PF restricted area and EF
restricted area. As differential pressure is constant, PF
flow becomes constant.
11-49
HYDRAULIC SYSTEM
Movement of
When extra flow (EF flow) is increased, pressure oil in valve spool
port P flows into damper chamber 5. As this passage
is the orifice on the edge of valve 8 only, movement of
valve spool 1 is slow. 5
11-50
HYDRAULIC SYSTEM
High-pressure
passage
valve 1 is pushed to the left (in the illustration), leaving
the seat. Pilot oil in the spring chamber flows in the
drain passage. Then, dump valve 2 moves to the left,
releasing a part or all of main flow to the low-pressure
passage.
This is a safety valve to protect the system. Low-pressure passage
Low pressure
passage
Pressure
Spring adjusting
screw
PF flow passage
213861
11-51
HYDRAULIC SYSTEM
4 2 7
Neutral
Descent Ascent
Main Components
1 Lift spool 7 Flow regulator valve
2 Valve body 8 Shut-off valve
3 Return spring
4 Check valve
5 Load check valve A1 : Lift cylinder port
6 Solenoid valve T2 : Tank port
Neutral position
Spool 1 is placed at the "neutral position" by return
spring 3 and oil in the A1 port is blocked by load check
valve 5.
As the center bypass port is open, oil pressure flows
into the tilt valve without being blocked.
11-52
HYDRAULIC SYSTEM
Neutral
Descent Ascent
11-53
HYDRAULIC SYSTEM
2
Hole
Neutral
Forward tilt Backward tilt
1
5 4 Center bypass port T2
213865
Main Components
1 Tilt spool 4 Tilt lock valve A2 : To tilt cylinder rod
2 Return spring 5 Tilt lock valve spring B2 : To tilt cylinder head
3 Check valve 6 Valve body
T2 : Tank port (return passage)
The above illustration shows the tilt control valve when Mast backward tilt position :
spool 1 is at the "neutral position."
Spool 1 moves to the right.
The B2 port is connected to the T2 port and the A2
Neutral position port is connected to passage A. The spool is posi-
Spool 1 is placed at the "neutral position" by return tioned to block the center bypass port, but since the
spring 2, and both the A2 port and B2 port are blocked spool is equipped with a hole under the land, it does
by the spool. not block it completely. This is designed to prevent a
As the center bypass valve is open, oil in the bypass large amount of oil from flowing at one time and to
port flows in the attachment valve. avoid abrupt movement of the cylinder, a characteristic
of this valve.
11-54
HYDRAULIC SYSTEM
3
A2 B2 6
2
5
Hole
Forward tilt Neutral
4
T2
Passage A
1
(b)
(a)
Chamber
(c)
213866
11-55
HYDRAULIC SYSTEM
1 Solenoid valve
2 Valve
2
Pilot passage
Parallel feeder
(high-pressure line)
T1
213867
11-56
HYDRAULIC SYSTEM
Clevis pin
Control
valve
Lift hose
217146
Installation
To install, follow the removal sequence in reverse.
Also follow the instructions given below:
Check the hydraulic oil level. Replenish it to the speci-
fied level if the level is low.
11-57
HYDRAULIC SYSTEM
10
9
5
4 2 6
3
1
Plug area
Locknut
Cap
7 8
213869
Sequence
I. Priority valve (1 thru 6)
1 Plug, O-ring 3 Spring 5 Ball
2 Spool assembly 4 Retainer 6 Plug, O-ring
II. Main relief valve (7)
7 Main relief valve
III. Steering system relief valve (8)
8 Steering system relief valve
IV. Other parts (9 and 10)
9 Plug, O-ring 10 O-ring
11-58
HYDRAULIC SYSTEM
10 11 12 14 15
13
Protrusion
amount of
set screw
Return spring 7
Cap screw
5
8
2
4 9
1
213870
Sequence
I. Lift valve (1 thru 9)
1 Check valve, spring 4 Spool, return spring 7 Bolt
2 Bolt 5 Plate 8 Plate
3 Cap 6 Seal 9 Seal
II. Load check valve (10 thru 15)
10 Plug, O-ring 12 Check valve 14 O-ring
11 Spring 13 Solenoid valve 15 Shut-off valve
III. Flow regular valve (16)
16 Flow regulator valve
11-59
HYDRAULIC SYSTEM
10 11 12 14 15
13
Protrusion
amount of
set screw
Return spring 7
Cap screw
5
8
2
4 9
1
213870
I. Sequence (1 thru 9)
1 Check valve, spring 4 Spool sub-assembly 7 Bolt
2 Bolt 5 Plate 8 Plate
3 Cap 6 Seal 9 Seal
II. Disassembly sequence of spool sub-assembly (10 thru 15)
10 Cap screw 12 Spring 14 Tilt lock valve
11 Spring retainer 13 Spring 15 Shut-off valve
III. Flow regulator valve (16)
16 Flow regulator valve
11-60
HYDRAULIC SYSTEM
3 12 5
7
10
11
2 6 13 14 1 4 9 8
213871
I. Sequence (1 thru 9)
1 Check valve, spring 4 Spool sub-assembly 7 Bolt
2 Bolt 5 Plate 8 Plate
3 Cap 6 Seal 9 Seal
II. Disassembly sequence of spool sub-assembly (10 thru 14)
10 Cap screw 12 Spring 14 Tilt lock valve
11 Spring retainer 13 Spring
III. Shut-off valve (15 thru 16)
15 Shut-off valve on the tilt cylinder
head side
16 Shut-off valve on the tilt cylinder
rod side
11-61
HYDRAULIC SYSTEM
Sequence
1 Solenoid valve
2 Plug, O-ring
3 Spring
4 Valve
5 Spring retainer
6 Ball
213872
Inspections after Disassembly
Valve, spool and return spring
(1) Check the valve body for cracks, damaged sliding
surface and wear of check valve seat.
(2) Check the spool for damage, seizure, bend and
operating force.
(3) Check the tilt lock valve for damage and seizure.
213873
11-62
HYDRAULIC SYSTEM
Reassembly
To reassemble, follow the disassembly sequence in
reverse. Also follow the instructions given below.
(1) Clean disassembled parts with an appropriate sol-
vent, and apply compressed air to the parts to dry
and remove foreign matters.
(2) Apply hydraulic oil to all parts. Tie bolt
11-63
HYDRAULIC SYSTEM
7. FC Control Valve
7.1 Structure and Operation
7.1.1 FC Control Valve – General
5 b1SOL
PF B2 B3
P
A2 A3
T2
A1
1 Inlet valve assembly P : Supplied oil from hydraulic pump (oil inlet port)
2 Tilt valve assembly T1 : To hydraulic tank (return line)
3 Attachment Valve Assembly
4 End cover assembly T2 : Return from steering valve (oil return port)
5 Solenoid lead wire and connector PF : To steering system
6 Solenoid for unload valve
A1 : To lift cylinder
7 Emergency shut-off valve (for release of lift lock)
8 Main relief valve (pilot) A2 : To tilt cylinder rod end
9 PF relief valve (steering system relief valve) B2 : To tilt cylinder head end
10 Emergency shut-off valve (for use as attachment)
A3 : To actuator for attachment valve
B3 : To actuator for attachment valve
c1 SOL :Solenoid for unload valve
a1 SOL, b1 SOL: Solenoid for lift valve
a2 SOL, b2 SOL: Solenoid for tilt valve
a3 SOL, b3 SOL: Solenoid for attachment valve
11-64
HYDRAULIC SYSTEM
Pp
P : Supplied oil from pump 3
PF : To steering system
4
7 6
T1 : To hydraulic tank
T2 : Return from steering system 1 2
A1 : To lift cylinder
c1 5
A2 : To tilt cylinder rod end
B2 : To tilt cylinder head end
A3 : To actuator for attachment valve P PF T2
213876
11-65
HYDRAULIC SYSTEM
A1
N N
b1 a1
8 3
M M
Pp
L P L
7
4
6
A1
c1 5
1
P PF T2 2
3
4 1
Section M - M Section L - L
2 6
Section N - N Section K - K
7
11-66
HYDRAULIC SYSTEM
PF
6 4 5
213883
11-67
HYDRAULIC SYSTEM
11-68
HYDRAULIC SYSTEM
9
7
8 3
10
2
5 4
D 1
Drain passage
6
C
A 213884
11-69
HYDRAULIC SYSTEM
Resistance Valve
3 2 C A B 4
Function of resistance valve
This is a valve to maintain pilot oil pressure for the
electromagnetic proportional pressure control valve of
the spool valve.
The illustration at the right shows a state where the
unload valve is open and the oil passage A has no oil
pressure built in it.
When the unload valve is closed, oil pressure of extra
flow in the oil passage A is increased. Oil enters the D
1 213885
cavity D from the hole C to cause the spool 2 to move
to the right against the force of the spring 4. As a
result, the oil passages A and B are opened and oil in 1 Resistance Valve 3 Slug
the oil passage is sent to the lift, tilt and attachment 2 Spool 4 Spring
valves.
A: Extra flow (EF flow) passage
In this way, the pressure in the oil passage A is main- B: Neutral passage in spool section
tained above a certain level during operation.
C: Hole
D: Cavity
Reducing Valve
3
Function of reducing valve
If extra oil is used directly as pilot oil for the electro- 2
magnetic proportional pressure control valve, the pres-
sure is too high for the purpose. This valve reduces
the pressure of extra flow to a proper level. E
A
F D
Action 1
When there is no oil pressure in the oil passage A, the B
spool 2 is pushed up by the spring 4 to the position
shown in the illustration at the right. When the spool is
in such state, the restricted area F is open to the maxi- C
mum and the oil passages A and B are open. 4
11-70
HYDRAULIC SYSTEM
Lift valve
22 20 16 15 3 17 11 2 19 10
7
5
6
21
14
4
13
Solenoid b1 Solenoid a1
12 18 8 9 1 12
Proportional electromagnetic
pressure reducing valve
217148
Main Components
1 Main spool 9 Low-pressure passage 16 Oil passage
2 Load check valve 10 Passage to port (A1) 17 Spring
3 Lift lock valve 11 Passage of pilot oil for actuating 18 Drain passage
4 Cap (solenoid a1 side) load check valve 19 Orifice
5 Spring (solenoid a1 side) 12 Passage of pilot oil for actuating 20 Shut-off valve
6 Cap (solenoid b1 side) spool 21 Spring preload adjusting
7 Spring (solenoid b1 side) 13 Oil passage screw
8 Neutral passage 14 Oil passage 22 Spool head
15 Oil passage
11-71
HYDRAULIC SYSTEM
2 1
6 7
4
Solenoid a1
Solenoid b1 12
(energized)
Proportional electromagnetic
pressure reducing valve 217149
11-72
HYDRAULIC SYSTEM
20 16 15 3 17 11 19 2 19 5
6
14
21
13
Solenoid b1 Solenoid a1
12 18
9 1
Proportional electromagnetic
pressure reducing valve
217150
Actuation of valve with Lift Lever in "Descent" Actuation of Valve with Lowering Speed Selector
Position: Switch in ON Position:
When the lift lever is moved into the "descent" posi- When this switch is set to ON, the maximum oil pres-
tion, an electric current proportional to the movement sure in the cap 6 can be held at a low level. This
of the lever is fed from the controller to the solenoid makes the stroke of the main spool 1 shorter and the
b1. The solenoid b1 is activated and pilot oil is return passage more restricted than when the switch is
released from the electromagnetic proportional pres- not used, and the maximum descending speed is
sure control valve into the cap 6 through the passage decreased as a result.
12. Actuation of Lift Lock Valve 3 in Case of Emer-
Pilot oil pressure in the cap is proportional to the gency:
movement of the lift lever. In case the main spool is stuck for some reason when
Pilot oil in the cap moves the main spool 1 to the right the lift cylinder descends, the movement of the cylin-
against the force of the spring 5. der rod can be stopped by returning the lift lever to the
At this point in time, pilot oil pressure passes the oil "neutral position. "With the lift lever back in the "neu-
passages 13 and 14 into the cavity on the left end of tral" position, pressure oil in the cap is released into
the lift lock valve 3 and moves the lift lock valve to the the drain passage 18 via oil passage 12.
right against the force of the spring 17. The lift lock valve 3 is returned by the spring 17 and
When this takes place, oil in the pilot passage 11 of the the pilot passage 11 is closed. The load check valve 2
load check valve 2 flows to the low-pressure passage is seated to block the flow from the port A.
9 through the oil passages 15 and 16. Actuation of Shut-Off Valve 20:
This oil flow gives rise to a pressure difference This is a valve used when the lift lock valve 3 is stuck
between before and after the orifice 19, which causes for some reason and the mast cannot be lowered.
the load check valve 2 to lift, releasing oil in the lift cyl- Loosening the valve opens the pilot passage 11 of the
inder into the tank from the port A1 through the low- load check valve 2. The load check valve 2 is then
pressure passage 9. lifted to release oil in the lift cylinder into the low-pres-
In the meantime, extra flow of oil runs into the tank sure passage 9, allowing the mast to lower.
because the neutral passage is not closed despite full
leftward stroke of the spool.
When the engine is stopped, even if the lift lever is
moved into the "descent" position, the lift lock valve 3
cannot be actuated due to lack of pilot oil pressure,
leaving the cylinder up as a result.
11-73
HYDRAULIC SYSTEM
Working of Spring Force Adjusting Screw 21: Use this screw for adjustment only when the descend-
ing speed is excessively different from set value.
This screw is for adjusting preload of the spring 5.
Where the pressure of pilot oil in the cap 6 is constant, Usually, leave the screw intact. Do not remove it at the
if the preload of the spring changes, the spool stroke is time of disassembly.
changed, so is the descending speed.
7 3 12 13 2 9 1 11
A2 B2 5
6
4
14
16
solenoid a2 Solenoid b2
8 10
15
Proportional electromagnetic
pressure reducing valve
213890
Main Components
1 Main spool 9 High-pressure passage (parallel feeder)
2 Check valve 10 Low-pressure passage (to T1)
3 Tilt lock valve 11 Passage to port (B2)
4 Cap (solenoid b2 side) 12 Passage to port (A2)
5 Spring (solenoid b2 side) 13 Oil passage
6 Cap (solenoid a2 side) 14 Passage of pilot oil for valve spool
7 Spring 15 Drain passage
8 Neutral passage 16 Chamber
Actuation of Valve with Attachment Lever in "Neu- As pressure oil does not flow into the chamber 16, the
tral" Position tilt lock valve 3 is pressed to the right by the spring 7.
When the tilt lever is in the "neutral" position, the pro-
portional solenoids a2 and b2 are inactive.
Since the electromagnetic proportional pressure con-
trol valve releases oil in the caps 4 and 6 into the drain
passage 15 through the passage 14, there is no pres-
sure in the caps.
Therefore, the main spool 1 is maintained in the posi-
tion shown in the illustration above, with the passages
to ports A2 and B2 closed.
Extra flow of oil divided by the priority valve of the inlet
valve assembly flows into the tank through the neutral
passage.
11-74
HYDRAULIC SYSTEM
3 12 2 9 1
7 A2 B2
5
6
Solenoid a2 Solenoid b2
(activated) 14 (not activated)
8 10
11-75
HYDRAULIC SYSTEM
2 9 1
A2 B2 5
4
Solenoid b2
8 14
12 13
Solenoid a2
3 10
Proportional electromagnetic
pressure reducing valve
Orifice (d):
A cluster of orifices. Capable of
preventing quick outflow of oil.
Actuation of Valve with Tilt Lever in "Forward Tilt" Actuation of Tilt Lock Valve in Case of Emergency
position
In case the main spool is stuck for some reason when
When the tilt lever is moved into the "forward tilt" posi- the mast tilts forward, returning the tilt lever to the
tion, an electric current proportional to the travel of the "neutral" position stops the movement of the cylinder
lever is fed from the controller to the solenoid b2. rod.
The solenoid b2 is activated and pilot oil is released With the tilt lever back in the "neutral" position, the
from the electromagnetic proportional pressure control unload valve of the inlet valve assembly is opened to
valve into the cap 4 through the passage 14. release extra flow of oil into the drain passage through
Pilot oil pressure in the cap is proportional to the the main relief valve.
movement of the lift lever. As a result, oil pressure in the passage 13 is reduced,
The pressure of pilot oil in the cap, which is propor- and oil pressure of the damper (e) is also reduced.
tional to the travel of the tilt lever, causes the main When this takes place, the tilt lock valve 3 is pushed to
spool 1 to move to the left against the force of the the right by the spring 7 and the route connecting the
spring 5 and closes the neutral passage 8. As a result, port A2 and low-pressure passage 10 is closed.
pressure in the high-pressure passage 9 rises. Oil in The tilt cylinder rod is brought into a locked state.
the passage pushes open the check valve 2 to flow to
the head side of the tilt cylinder through the passage
13 and port B2, causing the cylinder rod to expand.
At this point in time, part of pressure oil in the passage
13 flows into the oil passage (a) and enters the
damper (e) to cause the tilt lock valve 3 to move to the
left against the force of the spring 7.
As a result, oil at the rod side of the tilt cylinder, that is
oil from the port A2, passes through the passage (b),
passage (c) and orifice (d) in that order into the low-
pressure passage 10.
The cylinder rod is extended by two actions combined,
i.e., supply of oil pressure from the port B2 and release
of pressure oil from the A2 port, and tilts the mast for-
ward.
11-76
HYDRAULIC SYSTEM
9 2 11 7 1 10
14 15
A3 B3 4
5 3
12
Solenoid a3 Solenoid b3
6 8
13
Proportional electromagnetic
pressure reducing valve
213893
Main Components
1 Main spool 7 High-pressure passage 12 Passage of pilot oil for valve spool
2 Check valve (parallel feeder) 13 Drain passage
3 Cap (solenoid b3 side) 8 Low-pressure passage (to T1) 14 Shut-off valve
4 Spring (solenoid b3 side) 9 Passage to port (A3) 15 Shut-off valve
5 Cap 10 Passage to port (B3)
6 Neutral passage 11 Passage (high-pressure passage)
Actuation of Valve with Attachment Lever in "Neu- The pressure of pilot oil in the cap, which is propor-
tral" Position tional to the travel of the tilt lever, causes the main
When the attachment lever is in the "neutral" position, spool 1 to move to the right against the force of the
the proportional solenoids a3 and b3 are inactive. spring 4 and closes the flow in the neutral passage 6.
The electromagnetic proportional pressure control As a result, pressure in the high-pressure passage 7
valve releases oil in the caps 3 and 5 into the drain rises. Oil in the passage pushes open the check valve
passage 13 through the passage 12 so that there is no 2 to flow to the actuator of the attachments through the
pressure in the caps. passage 11 to 9 and port A3.
This maintains the main spool 1 in the position shown Oil from the port B3 flows to the tank from the low-
in the illustration above by the spring 4 with the pas- pressure passage 8.
sages connecting to the ports A3 and B3 closed. The shut-off valves 14 and 15 are for releasing oil from
Extra flow of oil divided by the priority valve of the inlet the ports A3 and B3 into the low-pressure passage 8,
valve assembly flows into the tank through the neutral respectively, in case of an emergency.
passage. Action of Valve When Solenoid b3 is Activated
Actuation of Valve When Solenoid a3 is Activated Activation of the solenoid b3 results in the action of the
When the solenoid a3 is activated, pilot oil flows into valve reverse to that when the solenoid a3 is activated.
the cap 5 through the passage 12. To be more specific, the valve spool 1 moves to the
Pilot oil pressure in the cap is proportional to the left, and oil flows to the attachment actuator from the
movement of the lift lever. port B3 and returns to the tank from the port A3.
For actuation of the electromagnetic proportional pres-
sure control valve, refer to Flow of Oil When Solenoid
is Activated.
11-77
HYDRAULIC SYSTEM
11-78
HYDRAULIC SYSTEM
7 6 4 3 2
Tightening torque:
16.7 ± 1.7 N·m
(1.7 ± 0.17 kgf·m)
1 [12 ± 1.3 lbf·ft]
B2 B3
Tightening torque:
44.1 ± 4.4 N·m
P
A2 A3
(4.5 ± 0.45 kgf·m)
A1 [33 ± 3.2 lbf·ft]
T3
217151
Suggestions for Disassembly (6) Use care not to damage the machined surfaces.
(1) Individual component valves can be removed sep- (7) The main spool and valve body are in a set. If
arately, with tie rods tightened, that is as assem- either the main spool or valve body is damaged,
bled. the whole valve section must be replaced in an
(2) When disassembly becomes necessary, find the assembly.
cause of the fault and determine the scope of dis- To avoid damage, when removing the lift lock
assembly. Depending on the nature of the fault, valve, etc. from the main spool, do not hold the
not only replacement of affected valve but exten- spool directly with a vise or pliers.
sive overhaul and flushing may be necessary. (8) Wash removed parts with clean solvent. Dry them
(3) Prior to disassembly, clean the outside of the con- using compressed air and place them on clean
trol valve assembly. sheets of paper or cloth.
(4) During disassembly, check for dirt and other for- (9) For disassembly of individual valves, refer to
eign matters in oil passages and stuck valves and "Reassembly of Valves."
poppets.
(5) In normal disassembling operation, do not loosen
the lock nuts for adjusting screws of pilot relief
valve, PF relief valve (steering relief valve) and
flow adjuster kit.
If the lock nuts are loosened and the adjusting
screws are moved, readjustment after reassembly
is required.
11-79
HYDRAULIC SYSTEM
11-80
HYDRAULIC SYSTEM
17
13
12
Tightening torque:
48 ± 4.8 N·m
(4.9 ± 0.5 kgf·m)
[35 ± 3.0 lbf·ft]
Tightening torque: 10
15.7 ± 1.6 N·m
(1.6 ± 0.16 kgf·m)
[11.5 ± 1.0 lbf·ft]
8 22 23 21 20 19 1 16 15 14 11
Tightening torque:
15.7 ± 1.6 N·m (1.6 ± 0.16 kgf·m) [11.5 ± 1.0 lbf·ft]
217152
11-81
HYDRAULIC SYSTEM
11-82
HYDRAULIC SYSTEM
1 Valve 4 Plug
2 O-ring 5 Lock nut
3 O-ring 6 Set screw
11-83
HYDRAULIC SYSTEM
Tightening torque: 9 6 5 3 4 2 1 13 10
15.7 ± 1.6 N·m
(1.6 ± 0.16 kgf·m)
[11.5 ± 1.0 lbf·ft]
7 12
Tightening torque:
63.7 ± 6.4 N·m
Tightening torque after set 8 11 (6.5 ± 0.65 kgf·m)
pressure adjustment:
[47 ± 4.7 lbf·ft]
9.8 ± 1.0 N·m
(1.0 ± 0.1 kgf·m) 20
[7.2 ± 0.7 lbf·ft] Tightening torque:
Tightening torque: 14 19 34.1 ± 3.4 N·m
63.7 ± 6.4 N·m (3.5 ± 0.35 kgf·m)
(6.5 ± 0.65 kgf·m) 15 [25.3 ± 2.5 lbf·ft]
30
[47 ± 4.7 lbf·ft]
29 Tightening torque:
34.1 ± 3.4 N·m
Tightening torque: 28 (3.5 ± 0.35 kgf·m)
15.7 ± 1.6 N·m [25.3 ± 2.5 lbf·ft]
(1.6 ± 0.16 kgf·m)
[11.5 ± 1.0 lbf·ft]
26
11-84
HYDRAULIC SYSTEM
Resistance Valve
(1) Install the spring 17 and slug 18 in the spool 16.
Apply hydraulic oil to the spool and insert it care-
fully into place in the housing.
(2) Fit the O-ring 20 on the plug 19, and screw in the
plug to the specified torque.
11-85
HYDRAULIC SYSTEM
11 21 8 9 23 22 13 16 1514 12
Tightening torque: Tightening torque: 34.3 ± 3.4 N·m
8.1 ± 0.9 N·m (3.5 ± 0.35 kgf·m) [25.3 ± 2.5 lbf·ft]
(0.8 ± 0.1 kgf·m)
[5.97 ± 0.6 lbf·ft] 28
27 Tightening torque:
147 ± 14 N·m
(15 ± 14.7 kgf·m)
[108 ± 10 lbf·ft]
213901
11-86
HYDRAULIC SYSTEM
Tilt valve
19
14
4
16 Solenoid a2 Solenoid b2
Tightening torque: Proportional electromagnetic
15.7 ± 1.6 N·m (1.6 ± 0.16 kgf·m) [11.5 ± 1.2 lbf·ft] 5
pressure reducing valve 213902
11-87
HYDRAULIC SYSTEM
Attachment valve
Tightening torque: 15.7 ± 1.6 N·m 12
(1.6 ± 0.16 kgf·m) [11.5 ± 1.2 lbf·ft]
Tightening torque:
34.3 ± 3.4 N·m
(3.5 ± 0.35 kgf·m)
[25.3 ± 2.5 lbf·ft] Tightening torque: 20.6 ± 2.1 N·m
Tightening torque: 9.8 ± 1.0 N·m (2.1 ± 0.21 kgf·m) [15.2 ± 1.55 lbf·ft]
3 1
(1.0 ± 0.1 kgf·m) [12.2 ± 1.2 lbf·ft] 2
Tightening torque: 18 19 17 16 5 11 6 7 9 8
21
Tightening first: 16.2 ± 1.6 N·m
(1.7 ± 0.17 kgf·m) [12.2 ± 1.2 lbf·ft]
Further tightening: 16.2 ± 1.6 N·m 20 A3 B3
(1.7 ± 0.17 kgf·m) [12.2 ± 1.2 lbf·ft]
10
14
13
Tightening torque:
15.7 ± 1.6 N·m
(1.6 ± 0.16 kgf·m)
15
[11.5 ± 1.2 lbf·ft]
4
Solenoid a3
Solenoid b3
Proportional electromagnetic
pressure reducing valve 213903
11-88