Beruflich Dokumente
Kultur Dokumente
·circuit diagram .................................................. ........... Twelve - BCM Input and output signal reference value ................................. 33
E
Driver control unit input and output signals - IPDM E / R Input and output signal reference value ........................ 33
No. reference value .................................................. ....... 13 Back door control unit input and output signals
- BCM Input and output signal reference value .............................. . . . . 13 No. reference value .................................................. ...... 34
- IPDM E / R Input and output signal reference value ..................... . . . . 14 - How to proceed with fault diagnosis .......................................... 34
Wiper amplifier input and output signal reference value ............. . . . . 14 Switch Monitor ............................................. 35 F
- How to proceed with fault diagnosis ....................................... . . . . 14 - Phenomenon by fault diagnosis Chart .................................. 36
And diagnosis before inspection ................................................. . . . . 14 Rear wiper of the power supply and the ground circuit system ... . . . 37
- CONSULT-II Function of ( BCM ) ...................... . . . . 15 Rear wiper actuation signal system ........................... 38
- CONSULT-II Function of ( IPDM E / R ) .................. Sixteen Rear wiper motor system ........................... 38
G
- Phenomenon by fault diagnosis Chart ................................... Sixteen Rear wiper position detection signal system .................... 39
Of the wiper amplifier power supply and the ground circuit system .... 17 Back door switch system ............................... Forty
Front wiper actuation signal system ..................... 19 Judder occurrence correspondence at the time of .................................. Forty
Front wiper motor system ..................... Twenty And removal of the rear wiper arm, mounting ... Forty
Front wiper motor drive signal system ....... Twenty Rear wiper arm of the stop position adjustment ............. 41 H
- Auto-stop signal system ............................ . . . .twenty one And removal of the rear wiper motor, Installing
Judder occurrence correspondence at the time of ................................... twenty three け .................................................. ................. 41
- Removing the front wiper arm, take Rear wiper blade .................................. 42
Bill .................................................. .......... . . . .twenty three Rear washer injection adjusting the position of the nozzle ... . . . 43
Front wiper arm of the stop position adjustment ....... twenty four Rear washer hose route ........................ 43 I
Front wiper motor - Removing the link Rear washer removal of the nozzle, take
Front washer injection position adjustment of the nozzle Rear wiper - Washer switch circuit
WW - 1
Power socket .................................................. .. . . . 47
- Removal of the rear power socket, mounting ... . . . 47
WW - 2
Notes on work
SRS Air bag, care about the pre-tensioner seat belt with a car JKS00C4D
warning : • SRS The configuration of the associated air bag and pretensioner seat belt system components desorption and harness desorption, key
switch OFF In, disconnect the negative battery terminal Three It is carried out after leaving more than minute. (For discharging the electricity stored in the auxiliary power
• The desorption of the components, air tools and power tools, etc. that you do not use. B
• SRS Air bag and harness for the pre-tensioner seat belt system is, that you do not repair by solder or the like. In addition, careful attention should be given to
interference with the biting and other parts of the harness.
• SRS That you do not use the electric tester such as circuit testers when the inspection of the air bag and pretensioner seat belt circuit and
separately state. (Working prevention by fine current of the tester)
C
• The connector of the air bag module and pre-tensioner seat belts, of foreign matter such as a driver plug is not. (Working preventing
electrostatic)
• SRS The airbag and pretensioner seat belt, using the yellow harness connector as identification, and to distinguish from other harness.
D
• For safety reasons, maintenance work, " SB Seat belt "and" SRS SRS Making reference to the air bag. "
• In front wiper operation, the wiper by an obstacle such as a snow can not be operated, it is possible to stop the operation of the wiper for motor protection. In
E
that case, the switch OFF After the removal of the obstacles to, about Twenty Again switch from elapsed seconds or more ON Front wiper begins to operate
when you.
• Due to factors such as snowfall, the operation of the rear wiper Ten If you stop sec or more BCM But to stop the operation of the rear wiper for motor protection. In this case
after removing the cause of the stop, once the rear wiper switch OFF About in the One The rear wiper switch after minute ON Or INT Resume the operation to be in.
F
• When I opened the hood in a state in which the front wiper was locked back, there is a case in which damage the hood.
• When the coating unevenness or part of the oil film adhesion and glass coating agent such as wax on the windshield glass is there is peeling, there is a case in positive not always be
G
• In continuous washer pump Thirty If the second is operated more, cause of failure.
JA
WW
WW - 3
Prepared by
name Use
CONSULT- Ⅱ
EG1187 0001
Diagnostic program card
EG1187 0100
(version JJD03C )
PBIA3527J
diagnostic connector
PBIA3526J
WW - 4
Front wiper washer system
• BCM Key switch ON The signal and the vehicle speed signal B / CAN Drivers using the communication C / U To send to.
• Wiper switch (combination switch) is Five And One of the output terminal Five It is composed of a combination of One of the input terminal, the driver of the combination
state of the terminals of the time you switch C / U It reads.
• driver C / U The front wiper LO , HI as well as INT To send an activation signal to the wiper amplifier. B
• Wiper amplifier LO , HI as well as INT To operate the front wiper motor by the actuation signal.
Feature Description
System chart C
PKIA4724J
G
Front wiper LO Actuation
• Key switch ON Sometimes, drivers C / U Front wiper by the reading function of the combination switch LO
But ON Upon detection of the state, the front wiper to the wiper amplifier LO To send an actuation signal.
• Wiper amplifier front wiper LO Upon receiving the operation, the relay built in the wiper amplifier ON By, the front wiper motor LO Actuate. H
• Key switch ON Sometimes, drivers C / U Front wiper by the reading function of the combination switch HI But
I
ON Upon detection of the state, the front wiper to the wiper amplifier HI To send an actuation signal.
• Wiper amplifier front wiper HI Upon receiving the operation, the relay built in the wiper amplifier ON By, the front wiper motor HI Actuate.
• Key switch ON Sometimes, drivers C / U Front wiper by the reading function of the combination switch INT
But ON Upon detection of the state, to the following working.
1. Between the combination switch ass volume One , Two , Three of ON / OFF It detects the state, to determine the wiper volume.
WW
2. BCM From B / CAN And a vehicle speed signal received by the communication, by the wiper volume, between you calculated ass pause time (in seconds).
After confirming the auto-stop signal, Front wiper between every calculated ass pause time INT To send a signal to the wiper amplifier.
• Wiper amplifier front wiper INT Driver a signal C / U Upon receiving from the relay built in the wiper amplifier ON By, front wiper motor LO In between L
to ass working.
WW - 5
Front wiper washer system
• The washer switch about 0.4 Sec or more ON Then, the wiper motor to work.
• The washer switch ON → OFF If you, OFF The wiper motor about from the time that became a Three Time to operate.
• The washer switch during intermittent working ON Then prioritize the washer switch.
Mist working
• MIST In automatic return type, any to the wiper One When you want to move only times and, a fine rain INT Even at the operating, to use when wiper actuation
feels early.
• With regard to working LO In the same control and the operation, the wiper One Time working to stop.
DESCRIPTION OF OPERATION
circuit diagram
PKIA4725J
WW - 6
Front wiper washer system
• 80A ( F / L-3 From) IPDM E / R of Two Backup power voltage is supplied to turn the terminal.
• IPDM E / R Department of 20A (# 73 Through) 19 From turn jack on the front wiper relay Five Backup power voltage is supplied to turn the terminal. The key switch ON If
you, the front wiper relay ON Next to the front wiper relay Three The turn terminal of the street Wye Paanpu Five A voltage is supplied to the turn terminal. at the same
time BCM It is B / CAN Key switch using the communication ON Dry bar signal C / U To send to. The front wiper switch LO When you position, the combination switch
front wiper LO Of contact ON become, INPUT1 When OUTPUT3 Circuit is conducting of. driver C / U Front wiper by the reading function of the combination switch LO But ON
B
Upon detection of the state, driver C / U of Five From turn terminal of the wiper amplifier Six Front wiper to turn terminal LO To send an actuation signal. Front wiper LO Wiper
amplifier which receives the actuation signal, the built-in relay ON Then, of the wiper amplifier One From turn terminal of the wiper motor One Supplying a voltage to
turn the terminal, the wiper motor Three Of the wiper amplifier through the turn terminal Three To the ground in turn end child, the front wiper LO Actuate.
• 80A ( F / L-3 From) IPDM E / R of Two Backup power voltage is supplied to turn the terminal.
• IPDM E / R Department of 20A (# 73 Through) 19 From turn jack on the front wiper relay Five Backup power voltage is supplied to turn the terminal. The key switch ON If
you, the front wiper relay ON Next to the front wiper relay Three The turn terminal of the street Wye Paanpu Five A voltage is supplied to the turn terminal. at the same
E
time BCM It is B / CAN Key switch using the communication ON Dry bar signal C / U To send to. The front wiper switch HI When you position, the combination switch
front wiper HI Of contact ON become, INPUT2 When OUTPUT1 Circuit is conducting of. driver C / U Front wiper by the reading function of the combination switch HI But ON
Upon detection of the state, drivers C / U of Six From turn terminal of the wiper amplifier Seven Front wiper to turn terminal HI To send an actuation signal. Front wiper HI
Wiper amplifier which receives the actuation signal, the built-in relay ON Then, of the wiper amplifier Three Turn terminal or al wiper motor Three Supplying a voltage to
F
turn the terminal, the wiper motor Two Of the wiper amplifier through the turn terminal Two To the ground in turn terminal, the front wiper HI Actuate.
Intermittent working
• 80A ( F / L-3 From) IPDM E / R of Two Backup power voltage is supplied to turn the terminal.
• IPDM E / R Department of 20A (# 73 Through) 19 From turn jack on the front wiper relay Five Backup power voltage is supplied to turn the terminal. The key switch ONH
If you, the front wiper relay ON Next to the front wiper relay Three The turn terminal of the street Wye Paanpu Five A voltage is supplied to the turn terminal. at the
same time BCM It is B / CAN Key switch using the communication ON Dry bar signal C / U To send to. The front wiper switch INT When you position, the
combination switch front wiper INT Of contact ON become, INPUT2 When OUTPUT3 Circuit is conducting of. driver C / U Front wiper is of the combination switch
1. Intermittent volume One , Two as well as Three of ON / OFF The state, wiper INT In the same manner as the driver C / U If There is detected, wiper
JA
To determine the state of the volume. Detail is "Intermittent working" ( WW-10 page ) See.
2. BCM From B / CAN And a vehicle speed signal received by the communication, by the wiper volume, the calculated intermittent pause time (in seconds).
Of the front wiper motor Five Driver from the turn terminal C / U of Twenty The driver of the auto-stop signal, which is input to turn terminal after the confirmation, in each between the
calculated ass pause time C / U of Five From turn terminal of the wiper amplifier Six Front wiper to turn terminal INT
WW
To send a signal.
WW - 7
Front wiper washer system
volume position wiper Vehicle speed about 35km / h More than the vehicle speed about 65km /
h The following vehicle speed about 65km / h that's all
Vehicle
Pause interval stop the vehicle speed at about 5kmspeed about
/ h that's all 35km / h Less than
Reference: A vehicle speed in the table may differ from the actual speed. Front wiper INT Wiper amplifier which receives the actuation signal, the built-in relay ON Then, of the
wiper amplifier One From turn terminal of the wiper motor One To supply a voltage to turn the terminal, the front wiper motor Three Of the wiper amplifier through the turn terminal Three
To the ground in turn terminal, the front wiper LO In between to ass working.
• 80A ( F / L-5 From) IPDM E / R of One Backup power voltage is supplied to turn the terminal.
• The key switch ON If you, 10A (# 85 From) twenty four The turn terminal of the street the combination switch Fifteen The power supply voltage is supplied to the turn terminal.
When the front wiper switch on the front washer position, the combination switch Five Watch- Shah motor from turn terminal One Supplying a voltage
to turn the terminal, the combination switch Sixteen , 14 Through the turn terminal is grounded, front washer motor is activated.
The contact at the same time of the combination switch front washer ON become INPUT1 When OUTPUT2 Circuit is turned on, and the washer motor 0.4 If it is
determined that the running second or more, the driver C / U It is to wiper amplifier LO To send the operation.
Washer switch OFF Driver that became a state C / U If There is detected, LO About the operation Three Times do stop.
Mist working
• The wiper switch MIST When position, wiper LO The operation One Times done and then stop.
Overview
• driver C / U Reads the state of the combination switch (lamps, wiper), based on the results, head Doranpu, performs the control of the relevant
systems, such as wiper.
• driver C / U It is Five One of the output terminal ( OUTPUT1 ~ Five )When Five One of the input terminal ( INPUT1 ~ Five A combination of), maximum Twenty
DESCRIPTION OF OPERATION
• driver C / U Always input terminal ( INPUT1 ~ Five And it outputs a power supply voltage from). At this time, the output terminal ( OUTPUT1 ~
Five ) Of electric current by operating the transistor in order. Wiper
WW - 8
Front wiper washer system
• The switch of any one (or more) ON If you, the voltage at the input terminals corresponding to the switch is changed, the driver
C / U Interface of the inner will detect the state, driver C / U Switch ON It is determined that the.
SKIA2833J
SKIA2834J I
Reference: Head lamp Two We have set the system of the switch.
• driver C / U It is OUTPUT3 Of the transistor ON When, INPUT1 The front wiper switch detects that the voltage has changed in LO Determined to be
a position, front wiper to the wiper amplifier LO To send an actuation signal.
WW
WW - 9
Front wiper washer system
• driver C / U Again OUTPUT3 When was activated of the transistor, INPUT1 Front wiper when it detects that the voltage has changed in LO It
recognizes that operation is continued.
SKIA2965J
Note: Each OUTPUT Transistor terminals 10ms Operating in the interval. Thus, the switch ON The electrical load from and to the
Delay until the operating results. However, the delay is a very small time positions which can not be recognized by the human senses.
Mode of operation
The combination switch reading function there is a mode of operation of the following.
1. Normal time
- driver C / U But when a non-sleep state, OUTPUT ( One ~ Five ) Is of the terminal each 10ms Each time ON-OFF Operate.
2. Sleep state
- driver C / U But when in the sleep state, OUTPUT1 as well as Two The transistor output is stopped, ing to the low current consumption mode. OUTPUT ( Three ~ Five ) Is 10ms
Each time ON-OFF Actuated, it accepts only the input of the light switch system.
SKIA2837J
Intermittent working
Ass volume between the combination switch is intermittent pause time of the wiper One , Intermittent volume Two , Intermittent volume Three of Three And One of the switch BCM A
WW - 10
Front wiper washer system
Combination switch
Ass interval between the wiper volume position
Intermittent volume One Intermittent volume Two Intermittent volume Three
Wiper volume 1 ON ON ON
small
During the reading function of the combination switch ass volume One , Two , Three of ON , OFF Driver the state C / U Will it detects. driver C / U Wiper
volume when the combination switch is in a state of the following One It will assume. D
JA
WW
PKIA4726J
WW - 11
Front wiper washer system
Front wiper SW , Front watch- Shah SW (combination Front wiper, front washer SW The driver of state C / U To send the signal.
SW )
CAN Vehicle speed signal and the key received by the communication SW of ON The signal B / CAN Dry bar in communication C /
BCM
U To send to.
driver C / U Of front wiper LO , HI as well as INT To send an activation signal to the wiper amplifier.
Wiper amplifier LO , HI as well as INT To send the wiper motor driving signal by the actuation signal.
PKIA4725J
WW - 12
Front wiper washer system
Driver control unit input and output signal reference value JKS00CV2
Measurement condition
Terminal
Signal name Key Reference value( V )
number Operation or state
SW
Wiper SW LO about 0
B
Five LO , INT Actuation signal ON
Wiper SW LO Excepting about 6.3
Wiper SW HI about 0
Six HI Actuation signal ON
Wiper SW HI Excepting about 9.5
Nine INPUT1 C
Ten INPUT2 11
17 B / CAN-L - - -
18 B / CAN-H - - -
25 OUTPUT 2
SKIA2656J
43 Earth ON - about 0
G
BCM Input and output signal reference value JKS00CV3
Measurement condition
Terminal
Signal name Key Reference value( V )
number Operation or state
SW H
One BAT Power supply OFF - Power-supply voltage
49 B / CAN-L - - - I
52 CAN-H - - -
53 Earth ON - about 0
63 B / CAN-H - - - JA
65 CAN-L - - -
WW
WW - 13
Front wiper washer system
Measurement condition
ON - Power-supply voltage
twenty four Washer SW
OFF - about 0
38 Earth ON - about 0
48 CAN-H - - -
49 CAN-L - - -
Measurement condition
Terminal
Signal name Key Reference value( V)
number Operation or state
SW
Two Wiper motor drive signal ON Wiper SW LO From HI about Twelve About from 0
Wiper SW LO about 0
Six LO , INT Actuation signal ON
Wiper SW LO Excepting about 6.3
Wiper SW HI about 0
Seven HI Actuation signal ON
Wiper SW HI Excepting about 9.5
1. The contents of to get the information from your failure to confirm the request.
2. To grasp the system overview. " System Overview "( WW-5 page ) To see.
3. To verify the configuration status of the system. " Before diagnosis inspection "( WW-14 page ) To see.
Five. Communicate diagnosis. " BCS Body Control System " "Communication Diagnostics" ( BCS-34 page ) To see.
6. From the phenomenon by fault diagnosis table, to repair or replace the cause of the failure. " Another fault diagnosis Chart phenomenon " (WW-16 page) To see.
7. Again, performing the operation check. If there is abnormal Two To implement the inspection again from the procedure.
8. Exit.
• CONSULT- In Ⅱ and the front display can be set change of the vehicle speed sensing wiper. Terminal number
WW - 14
Front wiper washer system
select a
OFF -
CONSULT- Ⅱ is BCM from CAN Receiving data by the communication line, a combination of transmission of the command, there is another work support display functions each site.
Beauty CONSULT- To connect the Ⅱ. For more information separate volume " CONSULT- Ⅱ instruction manual
E
(Supplement Three )"as well as" CONSULT-
• [ BCM ] If you do not display, "diagnostic system selection" screen after printed out, " CONSULT-II
Note at the time of use "( LAN-2 page ) See. H
SKIA6261J
For more information, separate " CONSULT- Ⅱ instruction manual (common) (Supplement One ) (Supplement Two
WW
SKIA2661J
WW - 15
Front wiper washer system
Work support
Vehicle speed sensing wiper setting
Operation procedure
3. Touch the vehicle speed sensing wiper setting] in the "work item selection" screen.
7. Touch [END].
CONSULT - Ⅱ is IPDM E / R With CAN "Receiving data" by the communication, there is a self-diagnosis, the ability to perform data monitor, the active test by the combination of the
• " The power supply and the ground circuit system of the wiper amplifier "( WW-17 page ) See.
• " LT Lighting systems " Inspection of the "combination switch "
(LT-126 page ) See.
Front wiper is not working • " Front wiper actuation signal system "( WW-19 page ) See.
• " Front wiper motor system "( WW-20 page ) See.
• " Front wiper motor drive signal line "( WW-20 page ) See.
• Front wiper drive ASSY Mechanical failure.
Front wiper does not return to the stop position " Auto-stop signal system "( WW-21 page ) See.
WW - 16
Front wiper washer system
It does not operate the front wiper is intermittent only " LT Lighting systems " "Inspection of the combination switch" ( LT-
126 page ) See.
• Confirmation of setting change function "Diagnosis before inspection" ( WW-14 page ) See.
B
It is not carried out the control of the speed of the intermittent time • " BCS Body Control System " "Communication Diagnostics" ( BCS-34 page
) See.
Wiper is not wiped off at the time of front washer " LT Lighting systems " "Inspection of the combination switch" ( LT126 page ) See.
working
The power supply and the ground circuit system of the wiper amplifier JKS00CVA
D
1. Fuse inspection
• Blow below the fuse is to check whether or not there.
# 73 20A IPDM E / R
Fuse position " PG Power supply - Earth - Circuit components "of "Terminal sequence" ( PG-3 page ) See.
F
Inspection results
OK » Two What
G
2. Front wiper relay power supply circuit inspection
1. Remove the front wiper relay.
2. Front wiper relay vehicle side harness connector One , Five Ban terminal
Terminal
Measurement condition Voltage( V)
(+) (-)
SKIA2949J
Inspection results
OK » Three What
JA
NG »To repair or replace the harness between the fuse-front wiper relay.
WW
WW - 17
Front wiper washer system
2. Front wiper relay vehicle side harness connector Two Ban terminal ~ Bo
Inspection results
OK » Four What
Inspection results
OK » Five What
SKIA2951J
2. Front wiper relay vehicle side harness connector Three Ban terminal ~ Wa
Ipaanpu vehicle side harness connector Five To check the continuity between the turn terminal.
Inspection results
OK » Six What
grounding.
Inspection results
To physical or exchange.
SKIA2953J
WW - 18
Front wiper washer system
Amplifier vehicle side harness connector Six To check the continuity between the turn terminal.
Inspection results
C
OK » Two What
SKIA2954J
NG »Driver C / U Repair the harness between ~ wiper amplifier
Or replace.
D
driver C / U Vehicle side harness connector Six Ban terminal ~ wiper amplifier vehicle side harness connector Seven
Inspection results
OK » Three What
F
NG »Driver C / U Repair the harness between ~ wiper amplifier
Or replace.
SKIA2955J
G
3. Front wiper actuation signal inspection
1. driver C / U And to connect the connector of the wiper amplifier.
Terminal
Measurement condition Voltage( V) I
(+) (-)
Wiper SW LO about 0
Five
Wiper SW LO Excepting
SKIA2956J
Body earth about 6.3
Wiper SW HI about 0
Six JA
Wiper SW HI Excepting about 9.5
Inspection results
WW - 19
Front wiper washer system
Inspection results
3. Front wiper motor vehicle side harness connector One , Two , Three Turn
Terminal-wiper amplifier vehicle side harness connector One , Two , Three To check the continuity between the
Inspection results
OK » Two What
NG »Front wiper motor - to repair or replace the harness between the wiper amplifier. Terminal
WW - 20
Front wiper washer system
3. To operate the wiper switch, the front wiper motor vehicle side
Harness connector One , Three The voltage across the terminals turn-body earth to point inspection.
B
Inspection results
2. The wiper switch LO The position, the driver C / U Vehicle side harness
Scan connector Twenty To check the voltage between the turn pin-body earth. F
Terminal
Measurement condition Voltage( V)
(+) (-)
body G
Twenty
Earth wiper SW LO about Twelve And about 0 repeat
SKIA2960J
Inspection results
OK » Five What
NG » Two What
H
3. Front wiper motor vehicle side harness connector Five Ban terminal ~
Wiper amplifier vehicle side harness connector Four To check the continuity between the turn terminal. JA
Inspection results
WW
SKIA2961J
OK » Three What
NG »Front wiper motor - to repair or replace the harness between the wiper amplifier. Terminal
WW - 21
Front wiper washer system
2. Front wiper relay vehicle side harness connector Three Ban terminal-off
Ron To wiper motor vehicle side harness connector Six To check the continuity between the turn
terminal.
Inspection results
OK » Four What
Front wiper motor vehicle side harness connector Four To check the continuity between the
Inspection results
SKIA2963J
2. Front wiper motor vehicle side harness connector Five Ban terminal ~
driver C / U Vehicle side harness connector Twenty To check the continuity between the turn terminal.
Inspection results
WW - 22
Front wiper washer system
Since the following causes can be considered, to identify the inspection to cause, to treat.
treatment
Oil film adhesion of the wax and the like to the window glass • Use the oil film up agents, and the like, to remove the oil film of the glass surface.
surface. • Oil of the wiper refill (wiper rubber) portion is also removed.
• Remove the blade from the wiper arm, to check the gap between the glass surface of the end of the arm and the wiper
stop position in the thickness gauge. Gap: about 0.6mm
C
• Adjustment, the arm tip Two Scissors using the
ELH0173D
E
Reference: Peeling of the oil film up and the glass coating agent, dropped Nissan genuine strong oil film ( KA200-89923 When you use)
Good.
removal
1. The wiper switch ON From to and, by operating the wiper motor OFF To (auto stop).
2. Open the hood and remove the nut cover wiper arm mounting nut (each One Remove the pieces). G
3. Lift the driver's seat side wiper arm, remove the wiper arm from the vehicle.
Four. Lift the passenger side wiper arm to close the hood, remove the wiper arm from the vehicle.
H
attachment
1. As the arm attachment sites cleaning and mounting nut is hard to loose, as shown in FIG.
To. Cause
JA
ELH0717D
WW
WW - 23
Front wiper washer system
2. As the center tip of the width of the wiper blade comes to the position shown in the figure, the word
The Lee par blade down on the surface of the glass. (When the blade tip Conform to
the marking that has been set in the blade set position of the black print set is easy.)
Torque with a wiper arm mounting nut tightening ( N - m { Kg- m}): 16.7 ~ 22.6 { 1.7
~ 2.3 }
Four. To inject the washer liquid. The wiper switch ON After actuating the wiper motor to OFF (An auto
To top).
Five. Wiper blades to make sure that you are stopped at the position shown in FIG.
Detail is, " Removing the front wiper arm, mounting "( WW-23 page ) See.
PKIA1397J
removal
1. Remove the front wiper arm. Detail is "Removing the front wiper arm, mounting" ( WW-23 page )
See.
2. Remove the cowl top cover. " EI Exterior - Interior "of "Cowl top" ( EI-14 page ) See.
WW - 24
Front wiper washer system
Four. Front wiper motor - Link mounting bolts ( Five Remove the book), the ring
Five. Take the wiper link from the wiper frame and the motor arm
remove.
6. Wiper motor mounting bolts ( Three Remove the book), or wiper frame
PKIA1398J
attachment C
1. The wiper motor connected to the vehicle side connector, the wiper switch ON Or by operating the wiper motor in the
Wiper motor mounting bolt tightening torque ( N - m { kg- m}): 5.0 ~ 6.0 { 0.5 ~ 0.61
}
E
Four. Attaching the wiper link to the wiper frame and the motor arm.
F
Wiper motor ASSY With mounting bolt tightening torque ( N - m { kg- m}): 3.8 ~ 5.1
{ 0.39 ~ 0.52 }
6. Wiper motor - Connect the link to the vehicle side connector, the wiper switch ON To, operate the wiper motor
The wiper switch from by OFF To (auto stop). G
7. Attach the cowl top cover. " EI Exterior - Interior "of "Cowl top" ( EI-14 page ) See.
8. Attaching the wiper arm. Detail is "Removing the front wiper arm, mounting" ( WW-23 page )
H
9. Do the stop position adjustment of the wiper arm.
Caution : • Dropping the wiper motor, it does not interfere with other parts.
• Note the grease state of the mating portion of the motor arm and the wiper link (retainer portion), to apply the grease as needed. Nisan MP I
A 262 439 80
WW
B 460 twenty five 110
L
PKIA1399J
WW - 25
Front wiper washer system
Injection position adjustment, insert the needle or the like is carried out by moving up and down, left and right to the injection holes.
PKIA4727J
PKIA4728J
removal
1. Open the hood.
2. Unlock the clip the nozzle elevation point side by pulling in the direction of the arrow, the nozzle
PKIA1402J
WW - 26
Front wiper washer system
When you blew in the forward direction (the injection hole side) you can ventilation, to check and not be able to
PKIA1403J
C
attachment
1. Attaching a washer tube to the nozzle.
3. Perform a nozzle injection position adjustment. " Injection position adjustment of the front washer nozzles "( WW-25 page ) See. D
Caution : Since the point There are different, it mounted so as not to mistake the left and right of the nozzle.
Detail is" LT Lighting systems " "Inspection of the combination switch" ( LT-126 page ) See. E
3. Figure the direction of the arrow to nail ( Two Wiper while pressing the point) - Washer scan
Pull the switch on the passenger side door direction, to the outside to take than the spiral cable. G
PKIA4729J
H
Front wiper - Removal of the washer tank, mounting JKS009XI
removal
1. Washer fluid inlet side of the screw ( One Washer to remove the book)
I
Remove the tank inlet from the vehicle.
JA
PKIA4730J
WW
WW - 27
Front wiper washer system
2. Remove the front side of the right fender protector. " EI Exterior -
Interior "of "Fender protector" ( EI-16 page ) See.
Five. Remove the washer hose, remove from the vehicle washer tank
It is.
PKIA4731J
attachment
Mounting with caution in the following tasks, carried out in the reverse order of removal.
Caution : After installation, put the water until the washer tank inlet top surface, to make sure that there is no water leakage.
Washer tank mounting bolt tightening torque ( N - m { kg-m }): 3.8 ~ 5.1 { 0.39 ~ 0.52
}
removal
1. Remove the front side of the right fender protector. " EI Exterior -
Interior "of "Fender protector" ( EI-16 page ) See.
PKIA4732J
attachment
Installation work is attention to the work of the following, carried out in the reverse order of removal.
Caution : When the washer pump installation, to make sure that the twist, etc. of the packing is not.
removal
1. IPDM E / R A remove. " PG Power supply - Earth - Circuit components "of " IPDM
2. Remove the connector of the wiper amplifier, IPDM E / R From the bracket
PKIA1422J
attachment
Installation is carried out in the reverse order of removal.
WW - 28
Rear wiper - Washer system
• BCM Key switch ON The signal B / CAN Back door using a communication C / U To send to.
• Wiper switch (combination switch) is Five And One of the output terminal Five It is composed of a combination of One of the input terminal, the driver of the combination
state of the terminals of the time you switch C / U It reads.
• driver C / U Operation and of the rear wiper INT Back door actuation signal C / U To send to. B
• back door C / U Rear wiper operation and is INT By the actuation signal to drive the rear wiper motor.
Feature Description
C
System chart
PKIA4733J
• Key switch ON Sometimes, the back door C / U When receiving the rear wiper operation, the rear To operate the wiper motor. H
• driver C / U Rear wiper by the reading function of the combination switch INT But ON Upon detection of the state, backdoors C / U To B / CAN Rear wiper with
communication INT To send an actuation signal.
I
• Key switch ON Sometimes, the back door C / U The rear wiper INT Upon receiving the activation signal, about the rear wiper motor Seven
To operate in the second interval.
• The rear washer switch about 0.4 Sec or more ON If you continue, rear wiper motor to work. JA
• The rear washer switch ON → OFF When, rear wiper One Time working to return to the set position. Thereafter, it operates as follows. Set position → Inverted position
(about Two Second pause) → Set position → Inverted position (about Two Second pause) → Set position
• The rear washer switch during intermittent working ON Then prioritize the rear washer switch. WW
WW - 29
Rear wiper - Washer system
DESCRIPTION OF OPERATION
circuit diagram
PKIA4734J
rear wiper motor through the turn terminal One The power supply voltage is supplied to the turn terminal. at the same time, BCM It is B / CAN Key switch using the
communication ON Back door signal C / U To send to. The rear wiper switch ON When you position, the contacts of the rear wiper combination switch ON become, INPUT5
When OUTPUT2 Circuit is conducting of. driver C / U Rear wiper by the reading function of the combination switch has ON Upon detection of a state, B / CAN The back door
of the rear wiper activation signal using the communication C / U To send to. Back door, which has received the rear wiper actuation signal C / U It is, of the rear wiper
motor Four Back door from turn terminal C / U of Ten Grounded in turn terminal, to operate the rear wiper motor. Contact of the back door switch When the back door is
open at the time of rear wiper actuated ON Next, the back door C / U of Sixteen Ban terminal is grounded. back door C / U Recognizes the back door is opened, and to
• 20A (# 41 Back door from) C / U of Four Backup power voltage is supplied to turn the terminal. The key switch ON If you, IPDM E / R of One From turn terminal twenty five Of the
rear wiper motor through the turn terminal One The power supply voltage is supplied to the turn terminal. at the same time, BCM It is B / CAN Key switch using the
communication ON Back door signal C / U To send to. The rear wiper switch INT When you position, the contacts of the rear wiper combination switch ON become, INPUT4
WW - 30
Rear wiper - Washer system
driver C / U Rear wiper by the reading function of the combination switch has ON Upon detection of a state, B / CAN Rear wiper using the communication INT Back door
actuation signal C / U To send to. Rear wiper INT Back door, which has received the actuation signal C / U It is, of the rear wiper motor Four Back door from turn terminal C
/ U of Ten
Grounded in turn terminal, about the rear wiper motor Seven To operate in the second interval.
• 80A ( F / L-5 From) IPDM E / R of One Backup power voltage is supplied to turn the terminal. B
• The key switch ON If you, 10A (# 85 From) twenty four Of the combination switch through the turn terminal Fifteen The power supply voltage is supplied to the turn terminal.
When the rear wiper switch to the rear washer position, the combination switch Five Washer motors from turn terminal One Supplying a voltage to turn the
terminal, the combination switch Sixteen , 14 Through the turn terminal is grounded, washer motors is activated. C
The contact at the same time of the combination switch rear washer ON become INPUT3 When OUTPUT2 Circuit is turned on, and the cormorant Ossha motor 0.4 If it is determined
that the running second or more, the driver C / U It is B / CAN The back door of the rear wiper actuation signal using a communication C / U To send to. The rear washer switch ON → OFF
When, rear wiper One Time working to return to the set position. After that, the sea urchin working good following. Set position → Inverted position (about Two Second pause) → Set
D
position → Inverted position (about Two Second pause) → Set position
E
Wiper switch reading function of driver control unit JKS00CVG
For more information about the features " Wiper switch reading function of driver control unit " (WW-8 page ) See.
JA
WW
PKIA4735J L
WW - 31
Rear wiper - Washer system
driver C / U Of front wiper LO , HI as well as INT Back door actuation signal C / U To send to.
back door C / U LO , HI as well as INT To rear wiper motor driven by the actuation signal.
PKIA4734J
WW - 32
Rear wiper - Washer system
Driver control unit input and output signal reference value JKS00CVJ
Measurement condition
Terminal
Signal name Key Reference value( V )
number Operation or state
SW
Eleven INPUT3 B
Twelve INPUT4
Light, turn, wiper OFF
ON State of
Wiper volume position Four time
13 INPUT5
C
SKIA2655J
17 B / CAN -L - - -
Eighteen B / CAN-H - - -
25 OUTPUT 2
D
E
SKIA2656J
43 Earth ON - about 0
F
Measurement condition
Terminal
Signal name Key Reference value( V )
number Operation or state
SW
52 CAN-H - - -
53 Earth ON - about 0
65 CAN-L - - -
Measurement condition
Terminal
Signal name Key Reference value( V)
number Operation or state
SW
38 Earth ON - about 0
48 CAN-H - - -
49 CAN-L - - -
WW - 33
Rear wiper - Washer system
Back door control unit input and output signal reference value JKS00CVM
Measurement condition
Five B / CAN-L - - -
Six B / CAN-H - - -
Nine Rear wiper position detection signal ON Rear wiper SW ON about Twelve And about 0 repeat
issue
about 0
Ten Rear wiper actuation signal ON Rear wiper SW O N
Rear wiper SW OFF about Twelve
1. The contents of to get the information from your failure to confirm the request.
2. To grasp the system overview. " System Overview "( WW-29 page ) See.
Four. Communicate diagnosis. " BCS Body Control System " "Communication Diagnostics" ( BCS-34 page ) To see.
Five. From the phenomenon by fault diagnosis table, to repair or replace the cause of the failure. " Another fault diagnosis Chart phenomenon " (WW-36 page) To see.
6. Again, performing the operation check. If there is abnormal Two To implement the inspection again from the procedure.
WW - 34
Rear wiper - Washer system
Five. The key switch ACC West, Ten The rear defogger switch within seconds Ten Press more times.
C
6. As a valve check, Five Seconds lamp is turned on.
7. While holding down the rear defogger switch to the lamp lit, the key switch ON When you switch the monitor is activated.
8. On the passenger side setting temperature display unit and the rear air conditioning setting temperature display unit 99 But
D
It is blinking, and operates the switch monitored switch, left and right map lamp
blinks, the buzzer of the roof C / U is sounding.
9. When the following conditions are met to terminate the switch monitor.
SKIA2769J
F
procedure Two (Car with navigation)
Five. Air conditioning OFF Press the switch, to stop the air conditioning. H
6. While holding down the vehicle information switch, temperature control dial (right) Ten Within seconds Thirty Click to manipulate or more.
JA
SKIA2767J
WW
WW - 35
Rear wiper - Washer system
8. Joystick " switch " When you select a switch monitor cause
To do.
9. On the passenger side setting temperature display unit and the rear air conditioning setting temperature display unit 99 But
It is blinking, and operates the switch monitored switch, left and right map lamp
blinks, roof C / U Buzzer is sounding.
Ten. When the following conditions are met to terminate the switch monitor.
SKIA2771J
• " The power supply and the ground circuit system of the rear wiper "( WW-37 page )
See.
• " LT Lighting systems " "Inspection of the combination switch" ( LT-126 page ) See.
Rear wiper does not return to the stop position " Rear wiper position detection signal line "( WW-39 page ) See.
" LT Lighting systems " "Inspection of the combination switch" ( LT-126 page ) See.
Rear wiper switch ON It does not operate only at the time of
• " LT Lighting systems " "Inspection of the combination switch" ( LT-126 page ) See.
It does not operate the rear wiper is intermittent only
• " Rear wiper position detection signal line "( WW-39 page ) See.
Wiper is not wiped off at the time of the rear washer working " LT Lighting systems " "Combination switch
inspection"( LT-126 page ) See.
Rear wiper does not stop when you open the back door " Back door switch line "( WW-40 page ) See.
" LT Lighting systems " "Lamp, abnormal operation movement of the wiper" ( LT-128
Rear wiper is abnormal operation
page ) See.
WW - 36
Rear wiper - Washer system
The power supply and the ground circuit system of the rear wiper JKS00CVQ
1. Fuse inspection
• Blow below the fuse is to check whether or not there.
Fuse position " PG Power supply - Earth - Circuit components "of "Terminal sequence" ( PG-3 page ) See.
Inspection results
C
OK » Two What
3. Rear wiper motor vehicle side harness connector One Ban terminal ~ Bo
E
To check the voltage between the Dee earth.
Inspection results
OK » Three What F
NG »The harness between the fuse - rear wiper motor Osamu SKIA2969J
To physical or exchange.
2. back door C / U Vehicle side harness connector Four Ban terminal ~ Body
Inspection results
OK » Four What
I
NG »Fuse - back door C / U Repair or exchange the harness between
To conversion. PKIA6033J
back door C / U Vehicle side harness connector Eleven To check the continuity between the turn pin-body
grounding.
Inspection results
Or replace. Fuse L
PKIA6034J
WW - 37
Rear wiper - Washer system
2. back door C / U And remove the connector of the rear wiper motor.
3. back door C / U Vehicle side harness connector Ten Ban terminal ~ Riyawai
Per motor vehicle side harness connector Four To point detects the conduction between the turn terminal.
Inspection results
NG »Back door C / U To repair or replace the harness between ~ rear wiper motor.
1. back door C / U And connect the connector of the rear wiper motor
To.
3. To operate the rear wiper switch, the back door C / U Vehicle side harness
Scan connector Ten To check the voltage between the turn pin-body earth.
Terminal
Measurement condition Voltage( V)
(+) (-)
Ten
Rear wiper SW OFF about Twelve
Inspection results
2. The connector on the rear wiper motor 12V Voltage added, Meaux
Terminal
Operation of the motor
(+) (-)
SKIA2974J
Inspection results
WW - 38
Rear wiper - Washer system
2. The rear wiper switch ON Then, back door C / U Vehicle side hard
Ness connector Nine To check the voltage between the turn pin-body earth. B
Body earth Rear wiper SW about Twelve And about 0 The provision for C
Nine
ON Return Ri
PKIA6037J
Inspection results
NG » Two What D
2. Rear wiper motor and the back door C / U Remove the connector.
3. Rear wiper motor vehicle side harness connector Two Ban terminal ~ back
Kudoa C / U Vehicle side harness connector Nine To check the continuity between the turn terminal.
Inspection results
I
Inspection results
WW
WW - 39
Rear wiper - Washer system
) See.
Inspection results
NG »Back door switch inspection" BL body - Lock - Security "on " Back door switch inspection " (BL-
45 page ) See.
treatment
Oil film adhesion of the wax and the like to the window glass surface. • Use the oil film up agents, and the like, to remove the oil film of the glass surface.
• Oil of the wiper refill (wiper rubber) portion is also removed.
Uneven coating, part scree of Garasuko coating agent was • Use the oil film up agents, and the like, to remove the coating agent of the glass surface.
applied to the window glass surface. • The coating on the glass surface is coated so that no uneven coating.
Reference: Peeling of the oil film up and the glass coating agent, dropped Nissan genuine strong oil film ( KA200-89923 When you use)
Good.
removal
Cause
1. The wiper switch ON From to and, by operating the wiper motor OFF To (auto stop).
3. Lift the wiper arm, remove the wiper arm from the vehicle.
attachment
1. The arm attachment sites were cleaned as shown in the figure, the mounting nut is hard to loose
So.
Conform to the marking that has been set in the black print of the grade set position.)
SKIA0082J
2. As the center tip of the width of the wiper blade comes to the position shown in the figure, the word
The Lee par blade down on the surface of the glass. (Easy to set when the blade tip
- 10 mm
PKIA1409J
WW - 40
Rear wiper - Washer system
3. The wiper arm nuts ( One Tightening in the present), attach the nut cover.
Torque with a wiper arm mounting nut tightening ( N - m { kg-m }): 4.0 ~ 6.0 { 0.41 ~
0.61 }
(Resin arm)
Four. To inject the washer liquid. The wiper switch ON A manner, the actuates the wiper motor OFF (Auto B
To stop).
Five. Wiper blades to make sure that you are stopped at the position shown in FIG.
Detail is, " Removing the rear wiper arm, mounting "( WW-40 page ) See.
PKIA4736J
removal
2. Remove the rear wiper arm. " Removing the rear wiper arm ,
attachment"( WW-40 page ) See.
Four. Remove the connector of the wiper motor on the back door inside. Rear
View camera mounted on vehicles, remove also the connector of the rear view camera. PKIA4737J
WW
Five. Remove the lead wire of a grommet that entered the back door from the wiper motor (for rubber watertight), of the wiper motor
Take out the connector and the connector of the rear view camera (rear view camera mounted on vehicles only).
6. Rear wiper motor mounting bolts ( Three Remove the book), remove the rear wiper motor from vehicle.
Caution : Dropping the rear wiper motor, it does not interfere with other parts.
L
WW - 41
Rear wiper - Washer system
attachment
Wiper motor mounting bolt tightening torque ( N - m { kg-m }): 3.8 ~ 5.1 { 0.39 ~
0.52 }
2. The back door of the connector and the connector of the rear view camera of the wiper motor (rear view camera mounted on vehicles only)
3. Fitting of the lead wire grommet (rubber for watertight) to the back door.
Four. The wiper motor connected to the vehicle side connector, the wiper switch ON Or by operating the wiper motor in the
Five. Installing a roof spoiler on the vehicle. " EI Exterior - Interior "of "Roof spoiler" ( EI-25 page ) See.
6. Mounting the wiper arm on the vehicle. Detail is " Removing the rear wiper arm, mounting " (WW-40 page ) See.
Torque with a wiper arm mounting nut tightening ( N - m { kg-m }): 4.0 ~ 6.0 { 0.41 ~
0.61 }
(Resin arm)
Removal, installation
removal
Arrows in FIG the wiper blade A In direction, unlock further turning from the stopper
position, remove.
PKIA1412J
attachment
WW - 42
Rear wiper - Washer system
A 35 Hundred Hundred
B 35 Hundred Sixty
PKIA1413J
Injection position adjustment, insert the needle or the like to the injection holes, carried out by moving up, down, left and right.
PKIA1414J
Detail is, " Washer hose route "( WW-26 page ) See. F
removal
G
1. The washer nozzle in the clockwise direction Ninety ° Turn, or rear spoiler
Et al pull out.
Caution : Washer hose removed the Do not dropped into the rear spoiler H
Strange that you stopped at the tape or the like.
I
PKIA4738J
When you blew in the forward direction (the injection hole side) you can ventilation, to check and not be able to
JA
WW
PKIA1416J
WW - 43
Rear wiper - Washer system
attachment
Mounting is performed in reverse order of removal.
Performing the rear washer jet position adjustment of the nozzle after installation.
Detail is," LT "Combination switch" in the lighting system. " " Inspection of the combination switch "( LT-126
page ) See.
Detail is, " Front wiper - Removal of the washer switch, mounting "( WW-27 page ) See.
Detail is, " Front wiper - Removal of the washer tank, mounting "( WW-27 page ) See.
Detail is, " Front wiper - Removal of the washer pump, mounting "( WW-28 page ) See.
WW - 44
Horn
removal
1. Remove the front grille upper. " EI Exterior - Interior "of "Front grille" ( EI-11 page ) See.
3. Horn mounting bolts (each One Remove the book), remove the horn from the vehicle.
PKIA1417J
D
attachment
Mounting note the work of the following, carried out in the reverse order of removal.
Horn mounting bolt tightening torque ( N - m { kg-m }): 5.00 ~ 6.79 { 0.51 ~ 0.69 } E
JA
WW
WW - 45
Cigarette lighter
removal
1. Installation lower center panel ASSY A remove. " IP Instrument panel "of "Removing, mounting" ( IP-5
page ) See.
3. Cigarette lighter socket inside of the square hole ( Two From the point) part, Shiga
Hold down the claws of the toilet writer ring remove Remove the pull connector
socket to the front.
PKIA1418J
attachment
Installation is carried out in the reverse order of removal and attention to the work of the following.
Caution : Align the cut-out portion of the cigarette lighter ring and the cigarette lighter socket is attached.
WW - 46
Power socket
removal
1. Remove the rear combination lamps lid of the luggage side.
While holding down the, remove press the inner socket to the front.
Four. The nails of the inner case with lid ( Two Press the point), Riyakonbine
Than tion lamp lid, remove the inner case with lid.
C
PKIA1420J
attachment D
Mounting note the work of the following, carried out in the reverse order of removal.
Caution : Align the groove of the inner case section and the inner socket and rear combination lamps lid with lid, taken
Put Ri.
JA
WW
WW - 47
Power socket
WW - 48