Sie sind auf Seite 1von 4

IMPORTANT: PLEASE KEEP THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE !

Copyright © 2010 by E&G Classics, Inc.


Notes to the Technician: All right reserved. The reproduction or
2010 Honda Accord E&G is proud to present this package to you and reminds you that utilization of this work in any form or
Crosstour Replacement for technical information, contact Lynn Eash or Lee Clary at 410- any electronic, mechanical, or other
means, no known or hereafter invented,
Fine Mesh Grille 381-4900. Do not attempt installation any E&G product without including xerography, photocopying,
first reading the detailed instructions. E&G Classics will not warrant and recording, and in any information
B 12 H0P damaged parts or vehicle due to altered installation instructions.
storage retrieval system is forbidden
without written permission of owners.

Part #1113-0102-10 Important information before you begin: 1


Quantity Description Part No.
This E&G grille installation kit includes grille
1 Upper Mesh Grille (includes): ************* hole location template(s) to drill mounting
(1) Top Plate 1113-0210-10
(1) 12 Gage Stainless Steel Surround 1113-0038-10 holes in the vehicle.
(1) Upper Mesh Section 1113-0020-10
(1) Lower Retainer w/Mounting Pins 1113-0042-10 Before marking or drilling any holes into the
(16) #8-32 ESNA Half Nuts 1999-0065-00
(2) Small Black Plastic Washers 1999-0256-00 vehicle, you MUST verify that the template(s)
1 Lower Chrome Plated Mesh Section 1113-0021-10 provided in this kit match the mounting pin
1 12 Gage Stainless Steel Surround 1113-0022-10 locations on the grille(s).
1 Hardware Kit (components listed below) 1113-1902-10
(8) 1” x .189” x .064” Black Plastic Washers 1999-0264-00
(10) #8-32 ESNA Half Nuts 1999-0065-00 Please place the assembled grille’s mounting
(2) 8-32 x .1” Black Cap Plugs 1999-0241-00 pins over the template(s) provided and make
(2) Universal Mounting Brackets 1108-0158-97
(1) Hole Location Template 1113-0039-10 sure that the pin and hole locations are the
(2) #10 Stainless Steel Lock Washers 1999-9555-00 same. If they do not match, please call: 1. Open the hood and lift up on the centers of the
(2) #8-32 Stainless Steel Hex Nuts 1999-9072-00 plastic push fasteners to release them. Unclip the
(1) Emblem Mounting Plate 1110-0158-08X *** 1-410-381-4900 *** side of the cover and remove the radiator cover.
(2)#8 x 3/8” Truss Head Screws 1999-9574-00
(2’) .030” x 1/4” Double Faced Tape 3004-9242-92 and ask for technical assistance. Thank you.
Upper Only Part #1113-010U-10
Quantity Description Part No.
1 Upper Mesh Grille (includes): *************
(1) Top Plate 1113-0210-10 3
(1) 12 Gage Stainless Steel Surround 1113-0038-10
(1) Upper Mesh Section 1113-0020-10
(1) Lower Retainer w/Mounting Pins 1113-0042-10
(16) #8-32 ESNA Half Nuts 1999-0065-00
(2) Small Black Plastic Washers 1999-0256-00
1 Hardware Kit (components listed below) 1113-1903-10
(1) Hole Location Template 1113-0039-10
(2) #10 Stainless Steel Lock Washers 1999-9555-00
(2) #8-32 Stainless Steel Hex Nuts 1999-9072-00
(1) Emblem Mounting Plate 1110-0158-08X
(2)#8 x 3/8” Truss Head Screws 1999-9574-00
(2’) .030” x 1/4” Double Faced Tape 3004-9242-92

2. Apply several layers of masking tape to the bumper 3. Remove the two (2) push pins secruing the small
cover surrounding the factory grille to protect the air defelctor on the left side of the grille opening
paint finish. and remove it for clearance (to be reinstalled once
the mesh grille is installed.
4

7
5
6

4. Remove the factory grille from the bumper cover by 6. Remove the front tag bracket is equipped by 7. Apply masking tape to the lower factory grille
unclipping the four (4) push fasteners from across removing the factory screws across the top of the opening to protect the paint during the lower
the bottom of the factory grille (see enlargement). front tag bracket (not shown) and the two 10mm grille installation.
5. Slide the grille mounting tabs out of the mounting hex bolts. Remove the factory clips from the For all cars: Paint any visible portion of the radiator
panel and remove the grille from the bumper cover. bumper cover (not reused). with flat or semi-gloss balck paint and allow to dry.
These steps will conceal everything behind the
mesh grille for a professional installation.

WARNING:
PLEASE HANDLE WITH CARE ! THE
8 EDGES OF THE STAINLESS STEEL MESH
& GRILLE CAN BE EXTREMELY SHARP!

10. Align the lower grille into place and install the sup-
8. Shop Tip: For cars painted colors other than black 9 plied mounting brackets over the side mounting
or dark blue: Tape 1/4” inside the upper bumper studs and secure them with an 8-32 ESNA half
opening and use a scotch brite pad or fine sand- 9. Align the lower mesh section over the back of the
lower surround and install the supplied .156” x 1” nut. There is enough access room from the top
paper to scuff the factory paint and paint the making it unecessary to remove the bumper cover.
return with flat or semi-gloss black paint. For all vinyl caps (once the closed ends have been cut off)
onto the lower and outer mounting studs to con- The top and bottom mounting studs are secured
cars: Paint any visible portion of the radiator and with a large black plastic washer and an 8-32
core support with flat or semigloss black paint and ceal them once the lower grille is installed.
ESNA half nut. Tighten until snug but do not over
allow to dry. tighten. Remove the protective masking tape.
2 Copyright 2010 by E&G Classics, Inc.
13

12

11
13. Cut out the supplied hole location template and
11. Remove the factory mounting tabs from the front 12. Using the factory screws, reinstall the modified fac- align it onto the bumper cover, making sure that
tag bracket as they would interfere with the lower tory tag bracket back onto the bumper cover. the template fits into the recess and is flush with
mesh grille. the face of the bumper cover and against the
side (A). Tape the template into place to prevent it
from shifting location. Use an awl or similar point-
ed tool to mark the hole locations onto the driver
side bumper cover. Untape the template and flip it
over to mark the passenger side hole locations.

14 15

14. Remove the template and drill through all marks 15. Remove the emblem from the factory grille and 16. Align the emblem mounting plate onto the mesh
made on the bumper cover with a .125” drill bit. install it onto the supplied emblem mounting plate grille, making sure that the plate is centered and
Use the drill bit to slot the double holes to make using the supplied double faced tape. Apply tape level. Look for small notches in the mesh to help
mounting slots to allow for left to right alignment around the perimeter of the emblem and one strip with proper alignment. Install the large black plas-
adjustments. down each side of the “H”. tic washers, #10 lock nuts and #8-32 stainless
steel hex nuts and tighten.

3 Copyright 2010 by E&G Classics, Inc.


8

9
17 20
19
17. Align the mesh grille mounting pins with the holes
drilled in Step 14. Once all the pins are aligned,
firmly push the mesh grille down to begin seating
the pins in the bumper cover but do not complete- 19. Use a .125” (1/8”) drill bit to drill through the exist- 20. Install the supplied #8 x 3/8” truss head screws
ly push the grille against the bumper cover. ing holes in the top plate. Blow off any plastic into the holes drill in the previous step, securing
18. Carefully remove the protective masking tape from shavings. the top plate to the bumper cover.
the painted bumper cover by peeling it back over
itself to minimize tape breakage (not shown), then
finsh pushing the grille tightly against the bumper
cover.

WARRANTY INFORMATION:
21 E&G Classics, Inc. warrants its chrome parts and products to be free from defects in mate-
rial, workmanship or finish for Thirty-Six (36) months from the date of shipment by E&G. This
warranty is limited to the repair or replacement, at E&G Classics option, of the defective part
or product.
To obtain performance under this warranty you must:
1.) Present your E&G unit to an authorized distributor in your area with proof of purchase.
2.) If no distributor is available, contact E&G Classics (address below) for authorization to
return unit.
3.) Returns - All unauthorized returns will be refused. Merchandise approved by E&G for
return must have been purchased within the Thirty-Six (36) months. All returns require an
authorization number obtained from E&G and the actual return must be accompanied by
the written authorization form filled out completely. All merchandise must be inspected
upon receipt and shortages reported within 48 hours. All merchandise must be in a resal
able condition. Merchandise must be packed carefully in the original packing. If original
packing is no longer usable, repack item(s) comparable to original manner. All returns are
subject to a 25% handling charge. Special order items are not returnable. Defective mer-
chandise must have an explanation of the problem. No credit will be issued unless invoice
number and date of purchase has been supplied. Manufacturer shall be sole judge of
defects in a product.
4.) UPS accounts - All returns must be prepaid. Do not send return shipments freight collect.
Once E&G has made its decision and it is a claim against our warranty policy, E&G will cred-
it incoming freight on damaged parts.
5.) No discontinued part or parts changed due to body style are returnable.
For Return Authorization, write or telephone: E&G Classics, Inc., 8910 McGaw Court,
Columbia, MD 21045 (410) 381-4900 Attn: Return Department.
You are responsible for inspecting all packages containing E&G Classics' parts and product imme-
21. Once the grille is in place, realign the radiator diately upon their receipt and must file a claim with the carrier for any damage disclosure by such
inspection and notify E&G classics in writing at the above address of any such damage. This war-
cover. Install the supplied push pins through the ranty does not extend to any of our products which have been subject to misuse, neglect, accident
cover and into the top plate on the E&G grille and or have been altered or repaired in any way. This warranty does not cover any accidental or conse-
quential damages for any breach of this warranty agreement. E&G Classics shall have no responsi-
through the bumper cover on the outer edges to bility for any loss of time, inconvenience, commercial loss or consequential damage, nor shall E&G
be liable for any injury or damage to persons or property by reason of any defect in material, work-
finish. manship or finish of its parts or products. This warranty gives you specific legal rights and you may
also have other rights which may vary from state to state.

4 Copyright 2010 by E&G Classics, Inc.

Das könnte Ihnen auch gefallen