Sie sind auf Seite 1von 18

18 Add extra over item Nos. 4.12.1to 4.12.

11 for doing centering & shuttering


work for each subsequent story (B-20/4:12:15)

19
Providing & fixing andized Aluminium Work (Anodyzing to be got done from
approved anodyzer for doors, windows, ventiletors & partition with extruded
builtup standard tubular & other sections of approved make confirming to
IS:733 and IS:1285 andyzed transperant 81 dyed to required shade
according to IS:1868 (Minimum anoic coating of grade AC 15), fixed with
rawl plugs and screws r with fixing clips, or with expansion hold fasteners
including necessary filling up of gas at junctions, at top, bottom and sides
with required PVC/neoprene felt etc. Aluminium section shall be smooth,
rust free, required including cleat angle Aluminium snap beading for
glazing/ paneling, C.P. brass / stainless steel screws, Al. Tower bolt & Al.
handle & Al. Aldrop etc. all complete as per architectural drawings and
directions of Engineer - in - charg. (Glazing and paneling to be paid for
separately) (B-157/16.1) 99.15
For Shutters of doors, windows & ventilators including providing and fixing
hinges/ rollers etc. and making provision for fixing of fittings wherever
required (locks shall be paid for extra) 102.13
20
Provideing and fixing 12 mm thick pre laminated three layer medium
density (exterior grade) praticle board Grade I, Type-II confirming to IS :
12823 bonded formaldehde synthetic resin, of approved brand and
manufacture in paneling fixed in aluminium doors, windows shutters and
partition frames with C.P. brass / stainless steel screws etc. complete as
per architectural drawings and direction of engineer-in-charge 77.87
Providing and fixing glazing in aluminium door, window, ventilator shutters
Pre-laminated
and partitions particle
etc. withboard with decorative
PVC/neoprene gasketlamination on one
etc. complete asside
per and
the
balancing lamination
architectural drawings onand
othertheside.
directions of engineer-in-charge (Cost of
21 aluminium
With glass snap
panesbeading shallthickness
of 5.0 mm be paid in basic item)
(weight not less than 13.75 kg./sqm)
as per IS : 2835 24.26
22
Providing and fixing PVC door frame made from extruded PVC confirming
to IS:10151-1982 section multi chamber cross section with a maximum wall
thickness of 2.8 mm ± 0.3 mm duly reinforced with steel tie rod at bottom,
and weather seals complete PVC door frame section (40 x 58 mm). As per
item No. 16.14.3 page No. B-159& B-160 59.40
23
Providing and fixing of plastic door shutter infill made form multi chamber
hollow PVC sections having cross section of 200 x 20 x 1 mm joined with
one another by a dove tail locking system and shutter frame made from
extruded PVC section in overall cross section of 59 x 24 mm and door
fittings such as hinges, aldrop, handles, stopper, locking bolt, will be
provided. As per item No. 16.15 page No. B-160 18.90
24
Providing and fixing double action hydraulic floor spring of approved brand
and manufacture to aluminium door shutter confirming to IS:6315 including
cost of cutting floors as required, embedding in floors and cover plate etc.
complete as per direction of Engineer-in-charge. 26.00
25 Providing and fixing brass lock without handle for Aluminium door, of
approved quality, make & design as directed by Engineer-in-Charge
Providing and fixing friction stay for aluminium windows, Ebco or
equivalent, complete in all respect size 10" 26.00
27 Polished Blue Kota stone flooring skirting, laid over 20 mm thick base of
C.M. 1:4 and jointed with grey cement slurry to match the shade of the slab
including rubbing and polishing complete:
For area of each slab upto 900 Sq. Cm. 25 mm thick slab As per item No.
11.35.1(a) page No. B-107 932.84
28 Polished Blue Kota Stone slab in steps, walls, pillars having fine machine
cut edges laid on 12 mm (Av.) thick cement mortar 1:3 and jointed with
grey cement slurry mixed with pigment to match the shade of the slab,
including rubbing and polishing complete:
25 mm thick slab area 901 to 2000 Sq.Cm. As per item No. 11.37.2 page
No.B-107 166.35
29 Providing and fixing 1st quality standard White/Ivory glazed tiles ISI marked
[IS: 13753] of size 300 mm x 200 mm in walls floors steps, pillars etc. laid
on a bed of neat cement slurry finished with flush pointing in white cement
mixed with pigment to match the shade of thecomplete (excluding the cost
of cement plaster) category - I Kajaria, Jhonson, Orient, Somani make etc.
B-47/7.3A 213.77
30 Providing and fixing 1st quality MAT finished ceramic tile size 300 x 300
mm confirming to IS: 13753 colour such as white, gray ivory, fume red
brown in walls, floor steps, pillars etc. laid on a bed of neat cement slurry
including nicely finished joints usingwater proof joint filler powder (Untile of
Roffe make) and finishing with flush pointing in white cement mixed with
pigment to match the shade of tile complete (excluding the cost of cement
plaster.) (B-47/7.4) 36.86
31 Extra for providing edge moldings to 18 mm thick marble stone counters,
vanities etc. over item No. 32 including machine polishing to edge to give
high gloss finish etc. complete as per design approved by Engineer-in-
charge. B-54/7.10.1 50.02
32 Plaster on new surface on walls in cement sand Mortar 1:4 including raking
of joints etc. complete fine finished:
20 mm thick As per item No. 12.8.2 Page No. B-113 1306.28
33 6mm thick cement plaster 1:3 finished with a floating coat of neat cement
sluury and thick coat of lime wash on top of wall when dry for bearing of rcc
slab & beam 3259.14
34 Distempering with oil bound washable distemper of approved branch and
manufactured to give an even shade including all scaffolding: new work
over and including scrapping and priming coat with cement cement primer.
B-120/12.51.1 2277.78
White washing with lime to give an even shade including all scaffolding:
new work three or more coats. B-119/12.44.1 981.37
35 Finishing wall with water proofing cement paint of approved brand and
manufacture and of required shade to give an even shade including all
scaffolding: two or more coats on new work. B-121/12.53.1 1306.28
36

Providing cement based water proofing treatment to RCC Roof with brick
bats in CM 1:4 (1 Cement : 4 Sand) the under layer being 20 mm thick bed
plaster of cement sand mortar 1:6 and a neat cement punning including
adding of water proofing compound at all stages at 2% of weight of cement
including curing etc. complete in all respect.
The various stages of executing the above mentioned item of work are as
given below:
1) Cleaning of RCC roof and applying of neat cement slurry over the roof at
the rate 3.00 kg, of cement per sqm. of area mixed with water proofing
compound. The thickness of layer be 1.50 mm.
2) Plastering the base with 20 mm thick cement mortar 1:6 with water
proofing compound.
3) Laying of brick bats with 20 mm thick cement mortar 1:4 with water
proofing compound.
4) Finishing with 20 mm thick cement sand mortar of mix 1:4 mixed with
water proofing compound. As per itm No. 10.52 Page No. B-97 980.00
37 Supplying and fixing in cement mortar welded hand railing made out of MS
round of square bars, flats etc. for staircase for verande as per design
complete in all respect (wooden or PVC hand railing to be paid extra with
priming coat of red oxide.) B-90/9.16 32.86
Bill of Quantities based on PWD BSR: Baran Circle 2005, PWD integrated BSR 1998 for Electrical Works and PWD
BSR 2003 for Road Work For:-
Name of Work : Construction of Auditorium at Township of 2 X 250 MW Chhbra Thermal Power Plant Project, Chhbra
Distt. Baran (Rajasthan)

Sr. No. Particulars Unit Qty. Rate

1 2 5 3 4
1
Site clearance including uprooting of trunk,
vegetation, bush woods, trees and sapling of girth
up to 15 cm and removal of rubbish etc. R-1/1-1 Per 100 Sqm 20.00 27.00
2
Earth work in excavation in foundation trenches of
drains including dressing of sides and ramming of
bottom, lift up to 1.5 Mtr including taking out the
excavated soil and depositing and refilling of jhire
with watering and ramming and disposal of surplus
excavated soil as directed within a lead of 50 Mtr.
In all kinds of soil B-2/1.8 Cu.m. 669.66 38.00
3
Earth work in excavation in foundation trenches of
drains including dressing of sides and ramming of
bottom, lift up to 1.5 Mtr including taking out the
excavated soil and depositing and refilling of jhire
with watering and ramming and disposal of surplus
excavated soil as directed with a lead in a 50
Metre including stacking of useful material if
available: (Hard rock (requiring blasting).usuful
material 30% (B-2/1.9.2) Cu.m. 315.77 162.00
4 Add extra over itm no. 2/3 for addititonal lift of 1.5
mtr there of
a) In any kind of soil Cu.m. 0.00 3.80
b) In ordinary rock and hard rock Cu.m. 315.77 9.90
4
5
Providing and laying in position cement concreting
including curing, compaction etc. complete using
stone aggregate 40mm nominal size (Hand broken)
in works upto plinth level excluding the cost of
shuttering, using 1 cement: 5 sand : 10 aggregate
mix) B-14/3.2.8 & 3.2.9
1 cement: 4 sand: 8 aggregate mix B-14/3.2.7 Cu.m. 47.36 1130.00
6
Filling in plinth with locally available river shingle
under floors including watering ramming
consolidating and dressing complete including cost
of shingle sand As per item No. 1.33 Page B-7
Cu.m. 980.52 250.00
7
Providing and injection Chlopyrifous Emulsifiable
concentrate 20% with 1% concentration for
PRECONSTRUCTIONAL Anti termite treatment as
per IS : 6313 part-III as amended from time to time
and creating a continious chemical barrier under
and arround the column pits, wall trenches,
basement excavation, top surface of plinth filling,
junction of wall and floor along the external
perimeter of building expansion joints, over the top
surface of consolidated earth of which aproch is to
be laid sorroundings of pipes and conduits etc.
complete as per specification (Plinth floor area only
shall be measured for payment.) As per item No.
1.39 page No. B-8 Sq.m. 1047.62 156.00
9

Providing and laying in position machine batched,


machine mixed and machine vibrated design mix
cement concrete of specified grade for reinforced
cement concrete structural elements, excluding the
cost of centering, shuttering and reinforcement
including curing, compaction, finishing with
rendering in cement sand mortar 1:3 (1 cement : 3
Coarse sand) and making good the joints and
Admixtures in recommended proportions as per IS
9103 to accelerate, retard setting of concrete
improve workability without impairing strength and
durability as per direction of Engineer-in-charge. M-
20 grade reinforced cement concrete. All work up to
plinth level. As per item No. 4.26 Page No. B-23

Cu.m. 280.51 2071.00

10
Providing and laying in position maching batched,
machine mixed and machine vibrated design mix
cement concrete of specified grade for reinforced
cement concrete structural elements, excluding the
cost of centering, shuttering and reinforcement
including curing, compaction finishing with rendering
in cement sand mortar 1:3 (1 Cement : 3 Coarse
Sand) and making good the joints and admixtures in
recommanded proportions as per IS : 9103 to
accelerate, retard setting of concrete improve
workability without impairing strength and durability
as per direction of engineer-in-charge. M-20 grade
reinforced cement concrete. All work from plinth
level up to floor three level. As per item No. 4.27
page No. B-24
Cu.m.
a Walls, columns, pillars, posts and struts As per item
No. 4.27.1 Page No. B-24 Cu.m. 87.61 2129.00
b Beams, plinth beams, girders, bressumers,
cantilevers, suspended floors, lintels, roofs and
staircases including spiral staircase, shelves etc. As
per item No. 4.27.2 page No. B-24 Cu.m. 454.14 2225.00
11 RR masonry for foundation and plinth with cement
mortar 1:6 (1 cement : 6 coarse sand) For above
30cm thick wall B-34/6.17 Cu.m. 55.04 815.00
12
Providing and laying horizontal damp proof course
with cement concrete grade M-150 (1:2:4) mortear
prepared with 1% solution of water proof compound
including two costs of hot blown bitumen 92 kg.per
sqm) complete as per specification with glass strip 3
mm thick at a distance of 1 m interval:100 mm thick
at a distance of 1 m interval:100 mm thiock (B-
160/15.2.4) Sq.m. 205.74 135.00
13 Brick masonary in foundation and plinth with bricks
of class designation 75 in cement morter 1:5 (B-
28/5.1.6 ) Cu.m. 417.80 1220.00
14 Add extra for brick masonry in super structure upto
third storey Cu.m. 417.80 75.00
15
Half brick masonry in super structure upto third story
using brick of class designation 75 in cement mortar
1:4 B-29/5.9 & 5.8.3 (Rs.155 + Rs10)
Sq.m. 147.04 165.00
16 Providing and fabricating reinforcement for RCC
work including straightening bending placing in
position and binding (including cost of binding wire)
all complete up to floor three level : Thermo-
mechanically Treated bars (Tata, SAIL) As per item
No. 4.13.4 Page B-20 Kg 57558.42 31.50

17
Centering & shuittering with plywoood sheet
including strutting propping bracing both ways with
wooden members and with removal of forms work
for super mstructure up to 4.5m hight above plinth
level for:a) suspended floors, roofs, landings, stair
case, balconies, girdeers cantilevers bends copings
bed plates anchor plates sills chhajjas lintels beams
etc.(B-19/4.12.2)
Sq.m. 70.00

18 Add extra over item Nos. 4.12.1to 4.12.11 for doing


centering & shuttering work for each subsequent
story (B-20/4:12:15) Sq.m. 5.00
19

Providing & fixing andized Aluminium Work


(Anodyzing to be got done from approved anodyzer
for doors, windows, ventiletors & partition with
extruded builtup standard tubular & other sections of
approved make confirming to IS:733 and IS:1285
andyzed transperant 81 dyed to required shade
according to IS:1868 (Minimum anoic coating of
grade AC 15), fixed with rawl plugs and screws r
with fixing clips, or with expansion hold fasteners
including necessary filling up of gas at junctions, at
top, bottom and sides with required PVC/neoprene
felt etc. Aluminium section shall be smooth, rust
free, required including cleat angle Aluminium snap
beading for glazing/ paneling, C.P. brass / stainless
steel screws, Al. Tower bolt & Al. handle & Al.
Aldrop etc. all complete as per architectural
drawings and directions of Engineer - in - charg.
(Glazing and paneling to be paid for separately) (B-
157/16.1)
a For fixed portion (frame) Kg 99.15 185.00
For Shutters of doors, windows & ventilators
including providing and fixing hinges/ rollers etc. and
making provision for fixing of fittings wherever
required (locks shall be paid for extra) Kg 102.13 193.00
20
Provideing and fixing 12 mm thick pre laminated
three layer medium density (exterior grade) praticle
board Grade I, Type-II confirming to IS : 12823
bonded formaldehde synthetic resin, of approved
brand and manufacture in paneling fixed in
aluminium doors, windows shutters and partition
frames with C.P. brass / stainless steel screws etc.
complete as per architectural drawings and direction
of engineer-in-charge
Pre-laminated particle board with decorative
lamination on one side and balancing lamination on
other side. Sq.m. 77.87 747.00
21
Providing and fixing glazing in aluminium door,
window, ventilator shutters and partitions etc. with
PVC/neoprene gasket etc. complete as per the
architectural drawings and the directions of
engineer-in-charge (Cost of aluminium snap
beading shall be paid in basic item)
With glass panes of 5.0 mm thickness (weight not
less than 13.75 kg./sqm) as per IS : 2835 Sq.m. 24.26 488.00
22
Providing and fixing PVC door frame made from
extruded PVC confirming to IS:10151-1982 section
multi chamber cross section with a maximum wall
thickness of 2.8 mm ± 0.3 mm duly reinforced with
steel tie rod at bottom, and weather seals complete
PVC door frame section (40 x 58 mm). As per item
No. 16.14.3 page No. B-159& B-160 Rmt 59.40 185.00
23
Providing and fixing of plastic door shutter infill
made form multi chamber hollow PVC sections
having cross section of 200 x 20 x 1 mm joined with
one another by a dove tail locking system and
shutter frame made from extruded PVC section in
overall cross section of 59 x 24 mm and door fittings
such as hinges, aldrop, handles, stopper, locking
bolt, will be provided. As per item No. 16.15 page
No. B-160 Sq.m. 18.90 1195.00
24
Providing and fixing double action hydraulic floor
spring of approved brand and manufacture to
aluminium door shutter confirming to IS:6315
including cost of cutting floors as required,
embedding in floors and cover plate etc. complete
as per direction of Engineer-in-charge. Each 26.00 1635.00
25 Providing and fixing brass lock without handle for
Aluminium door, of approved quality, make & design
as directed by Engineer-in-Charge Each 225.00
Providing and fixing friction stay for aluminium
windows, Ebco or equivalent, complete in all respect
size 10" Each Pair 26.00 228.00
27
Polished Blue Kota stone flooring skirting, laid over
20 mm thick base of C.M. 1:4 and jointed with grey
cement slurry to match the shade of the slab
including rubbing and polishing complete:

For area of each slab upto 900 Sq. Cm. 25 mm thick


slab As per item No. 11.35.1(a) page No. B-107 Sq.m. 932.84 300.00
28 Polished Blue Kota Stone slab in steps, walls, pillars
having fine machine cut edges laid on 12 mm (Av.)
thick cement mortar 1:3 and jointed with grey
cement slurry mixed with pigment to match the
shade of the slab, including rubbing and polishing
complete:
25 mm thick slab area 901 to 2000 Sq.Cm. As per
item No. 11.37.2 page No.B-107 Sq.m. 166.35 365.00
29
Providing and fixing 1st quality standard White/Ivory
glazed tiles ISI marked [IS: 13753] of size 300 mm x
200 mm in walls floors steps, pillars etc. laid on a
bed of neat cement slurry finished with flush
pointing in white cement mixed with pigment to
match the shade of thecomplete (excluding the cost
of cement plaster) category - I Kajaria, Jhonson,
Orient, Somani make etc. B-47/7.3A
Sq.m. 213.77 438.00
30
Providing and fixing 1st quality MAT finished
ceramic tile size 300 x 300 mm confirming to IS:
13753 colour such as white, gray ivory, fume red
brown in walls, floor steps, pillars etc. laid on a bed
of neat cement slurry including nicely finished joints
usingwater proof joint filler powder (Untile of Roffe
make) and finishing with flush pointing in white
cement mixed with pigment to match the shade of
tile complete (excluding the cost of cement plaster.)
(B-47/7.4)
Sq.m. 36.86 449.00
31
Extra for providing edge moldings to 18 mm thick
marble stone counters, vanities etc. over item No.
32 including machine polishing to edge to give high
gloss finish etc. complete as per design approved
by Engineer-in-charge. B-54/7.10.1 Rmt 50.02 125.00
32 Plaster on new surface on walls in cement sand
Mortar 1:4 including raking of joints etc. complete
fine finished:

20 mm thick As per item No. 12.8.2 Page No. B-113 Sq.m. 1306.28 50.00
33 6mm thick cement plaster 1:3 finished with a floating
coat of neat cement sluury and thick coat of lime
wash on top of wall when dry for bearing of rcc slab
& beam Sq.m. 3259.14 55.00
34 Distempering with oil bound washable distemper of
approved branch and manufactured to give an even
shade including all scaffolding: new work over and
including scrapping and priming coat with cement
cement primer. B-120/12.51.1 Sq.m. 2277.78 18.00
35 White washing with lime to give an even shade
including all scaffolding: new work three or more
coats. B-119/12.44.1 Sq.m. 981.37 4.00
36 Finishing wall with water proofing cement paint of
approved brand and manufacture and of required
shade to give an even shade including all
scaffolding: two or more coats on new work. B-
121/12.53.1 Sq.m. 1306.28 15.00
37

Providing cement based water proofing treatment to


RCC Roof with brick bats in CM 1:4 (1 Cement : 4
Sand) the under layer being 20 mm thick bed
plaster of cement sand mortar 1:6 and a neat
cement punning including adding of water proofing
compound at all stages at 2% of weight of cement
including curing etc. complete in all respect.
The various stages of executing the above
mentioned item of work are as given below:
1) Cleaning of RCC roof and applying of neat
cement slurry over the roof at the rate 3.00 kg, of
cement per sqm. of area mixed with water proofing
compound. The thickness of layer be 1.50 mm.
2) Plastering the base with 20 mm thick cement
mortar 1:6 with water proofing compound.
3) Laying of brick bats with 20 mm thick cement
mortar 1:4 with water proofing compound.
4) Finishing with 20 mm thick cement sand mortar of
mix 1:4 mixed with water proofing compound. As
per itm No. 10.52 Page No. B-97 Sq.m. 980.00 220.00
38
Supplying and fixing in cement mortar welded hand
railing made out of MS round of square bars, flats
etc. for staircase for verande as per design
complete in all respect (wooden or PVC hand railing
to be paid extra with priming coat of red oxide.) B-
78/9.16 Kg 32.86 35.00
Total Civil Cost Rs:
Electrical Works and PWD

ower Plant Project, Chhbra

Amt.

540.00

25446.95

51154.09

0.00
3126.08

53522.34

245129.28
163428.72

580936.64

186517.39
1010472.51

44861.10

27774.44

509717.30

31335.08

24261.86

1813090.22

0.00

0.00 4771
51.04
18342.75

19711.48 2.88 1.956522 0.23 0.45

1.956522 0.7 1.369565 1.5 0.3

58167.40 1.82 sq m / cum 1.5 0.45

0.00 8.333333 8.33 sq m / cu m 2.3 0.1


10989.00

22585.50

42510.00

0.00

5928.00

279852.00

60718.48
93630.38

16550.14

6252.50

65314.22

179252.77

40999.95

3925.46

19594.27
215600.00

1150.24
5932388.55
5649.89
1.125 2.25

0.45

0.675

2 0.46

Das könnte Ihnen auch gefallen