Sie sind auf Seite 1von 8

IMPORTANT: PLEASE RETAIN THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE

Copyright © 2009 by E&G Classics, Inc.


2010 Chevrolet Camaro Notes to the Technician: All right reserved. The reproduction or
E&G is proud to present this package to you and reminds you that utilization of this work in any form or
Mesh Grille Installation for technical information, contact Lynn Eash or Lee Clary at 410- any electronic, mechanical, or other
means, no known or hereafter invented,
Instructions 381-4900. Do not attempt installation any E&G product without including xerography, photocopying,
first reading the detailed instructions. E&G Classics will not warrant and recording, and in any information
D 06 H0 R storage retrieval system is forbidden
damaged parts or vehicle due to altered installation instructions. without written permission of owners.

“Base”& “RS” Part #1412-0102-10R “SS” Part #1412-0102-10SSR “Base”& “RS” Black Ice Part #1412-B102-10R
Quantity Description Part No. Quantity Description Part No. Quantity Description Part No.
1 Upper Fine Mesh Grille (includes): ************* 1 Upper Fine Mesh Grille (includes): ************* 1 Upper Fine Mesh Grille (includes): *************
Chrome Plated Surround 1412-0034-10R Chrome Plated Surround 1412-0034-10R Chrome Plated Surround 1412-0034-10R
Chrome Plated Mesh Section 1412-0020-10 Chrome Plated Mesh Section 1412-0020-10 “Black Ice” Mesh Section 1412-0020-10BI
(4) 5” Black Cable Ties 1999-0301-00 (4) 5” Black Cable Ties 1999-0301-00 (4) 5” Black Cable Ties 1999-0301-00
1 Lower Fine Mesh Grille (includes): ************* 1 Lower Fine Mesh Grille (includes): ************* 1 Lower Fine Mesh Grille (includes): *************
Stainless Steel Surround 1412-0022-10 Stainless Steel Surround 1412-0022-10SS Stainless Steel Surround 1412-0022-10
Chrome Plated Mesh Section 1412-0021-10 Chrome Plated Mesh Section 1412-0021-10SS “Black Ice” Mesh Section 1412-0021-10BI
(4) 5” Black Cable Ties 1999-0301-00 (4) 5” Black Cable Ties 1999-0301-00 (4) 5” Black Cable Ties 1999-0301-00
(5) #8 x 1-1/4” Black Cap plugs 1999-0311-00 (5) #8 x 1-1/4” Black Cap plugs 1999-0311-00 (5) #8 x 1-1/4” Black Cap plugs 1999-0311-00
1 Set 22 Gage Polished S.S. Fillers Right 1412-0035-10 1 Set 22 Gage Polished S.S. Fillers Right 1412-0035-10 1 Set 22 Gage Polished S.S. Fillers Right 1412-0035-10
Left 1412-0036-10 Left 1412-0036-10 Left 1412-0036-10
1 Hardware Kit (components listed below): 1412-1902-10R 1 Hardware Kit (components listed below): 1412-1902-10R 1 Hardware Kit (components listed below): 1412-1902-10R
(4) Small Black plastic Washers 1999-0256-00 (4) Small Black plastic Washers 1999-0256-00 (4) Small Black plastic Washers 1999-0256-00
(6) 5/16” PVC Spacers 1999-0273-00 (6) 5/16” PVC Spacers 1999-0273-00 (6) 5/16” PVC Spacers 1999-0273-00
(16) #8-32 ESNA Half Nuts 1999-0065-00 (16) #8-32 ESNA Half Nuts 1999-0065-00 (16) #8-32 ESNA Half Nuts 1999-0065-00
(10) 1.006” x.189” x.062” Black Plastic Washers 1999-0264-00 (10) 1.006” x.189” x.062” Black Plastic Washers 1999-0264-00 (10) 1.006” x.189” x.062” Black Plastic Washers 1999-0264-00
(1) “Bow Tie” Emblem Backing Plate 1412-0158-10 (1) “Bow Tie” Emblem Backing Plate 1412-0158-10 (1) “Bow Tie” Emblem Backing Plate 1412-0158-10
(1) Logo Emblem Backing Plate 1412-0159-10 (1) Logo Emblem Backing Plate 1412-0159-10 (1) Logo Emblem Backing Plate 1412-0159-10
(1) Emblem Hole Location Template 1412-0069-10 (1) Emblem Hole Location Template 1412-0069-10 (1) Emblem Hole Location Template 1412-0069-10
(1) Mounting Hole Location Template 1412-0068-10 (1) Mounting Hole Location Template 1412-0068-10 (1) Mounting Hole Location Template 1412-0068-10
(42”) .045” x .250” Double Faced Tape 3004-9250-92 (42”) .045” x .250” Double Faced Tape 3004-9250-92 (42”) .045” x .250” Double Faced Tape 3004-9250-92
(1) “SS” Lower Hole Location Template 1412-0068-10SS (1) “SS” Lower Hole Location Template 1412-0068-10SS (1) “SS” Lower Hole Location Template 1412-0068-10SS
(6”) .045” x 1” Double Faced Tape 3004-9244-92 (6”) .045” x 1” Double Faced Tape 3004-9244-92 (6”) .045” x 1” Double Faced Tape 3004-9244-92
(4) #6 x 1/2” Countersunk Phillips Screws 3999-9026-00 (4) #6 x 1/2” Countersunk Phillips Screws 3999-9026-00 (4) #6 x 1/2” Countersunk Phillips Screws 3999-9026-00
(1) #10 Lock Washer 1999-9555-00 (1) #10 Lock Washer 1999-9555-00 (1) #10 Lock Washer 1999-9555-00
(1) #8-32 S.S. Hex Nut 1999-9072-00 (1) #8-32 S.S. Hex Nut 1999-9072-00 (1) #8-32 S.S. Hex Nut 1999-9072-00

1
***** IMPORTANT! *****
The exposed edges of the grille sur-
rounds and mesh can be extremely
sharp. Please handle with care.

**** IMPORTANT **** 1. Remove the 10mm hex bolts from the metal shield and
Raise the vehicle on a lift. When lifting with a jack, install jack remove it from the vehicle for grille installation access.
stands underneath the front subframe. Do not rely solely on
the jack to support the front of the vehicle.
“SS” Black Ice Part #1412-B102-10SSR
Quantity Description Part No.
1 Upper Fine Mesh Grille (includes): *************
Chrome Plated Surround 1412-0034-10R
“Black Ice” Mesh Section 1412-0020-10BI
(4) 5” Black Cable Ties 1999-0301-00
1 Lower Fine Mesh Grille (includes): ************* 2
Stainless Steel Surround 1412-0022-10SS
“Black Ice” Mesh Section 1412-0021-10SSBI
(4) 5” Black Cable Ties 1999-0301-00
(5) #8 x 1-1/4” Black Cap plugs 1999-0311-00
1 Set 22 Gage Polished S.S. Fillers Right 1412-0035-10
Left 1412-0036-10
1 Hardware Kit (components listed below): 1412-1902-10R
(4) Small Black plastic Washers 1999-0256-00
(6) 5/16” PVC Spacers 1999-0273-00
(16) #8-32 ESNA Half Nuts 1999-0065-00
(10) 1.006” x.189” x.062” Black Plastic Washers 1999-0264-00
(1) “Bow Tie” Emblem Backing Plate 1412-0158-10 2. Remove the factory push fasteners from across the front 3. You must mark the location of the hood latch assembly,
(1) Logo Emblem Backing Plate 1412-0159-10 edge of the bumper cover by lifting up on the top portion then use a 13mm wrench to remove it from the core sup-
(1) Emblem Hole Location Template 1412-0069-10 of the push fastener until it rises approximately 1/2” (see port. This will give you adequate room for Mesh Grille
(1) Mounting Hole Location Template 1412-0068-10 inset photo), then pull the entire push fastener up and out installation.
(42”) .045” x .250” Double Faced Tape 3004-9250-92 of each mounting hole. Once all the push fasteners have
(1) “SS” Lower Hole Location Template 1412-0068-10SS been removed, lift the panel out of the way for hood
(6”) .045” x 1” Double Faced Tape 3004-9244-92 catch removal.
(4) #6 x 1/2” Countersunk Phillips Screws 3999-9026-00
(1) #10 Lock Washer 1999-9555-00
(1) #8-32 S.S. Hex Nut 1999-9072-00

4 6

4. Use a large flat blade screwdriver to remove the factory 5. These are the outer tabs that you need to push down on 6. Apply protective masking tape around the edges of the
bow tie emblem from the factory grille. This is not an easy to remove the emblem (one per side). headlight assemblies, upper and lower grille openings to
step, but with patience you will be able to remove the protect the painted bumper cover.
emblem by inserting the screwdriver between the emblem
mounting tabs and the grille and twisting back and forth.
This opens up the mounting slots in the grille.

Copyright © 2009 by E&G Classics, Inc.


2
8

7
9

7. For “SS” models: Cut out and align the lower hole loca- 8. For “SS” models: Use a 5/16” drill bit to drill through the 9. Remove the two (2) lower 10mm factory bolts from
tion template onto the lower grille in the bumper cover marks made in the plastic lower grille prior to grille align- underneath the bumper cover.
opening and use masking tape to hold it in place. Use an ment.
awl or similar pointed tool to mark the hole location
onto the plastic grille (as shown). Untape the template,
flip it over and mark the opposite side.

10

11

10. Cut two (2) 6” long pieces of 2 x 4 and use them to hold 11. Cut off the closed ends from the preinstalled lower grille 12. Align the lower mesh section and surround into place,
the bottom edge of the bumper cover down for lower black cap plugs and push the sleeves down over the making sure the outer studs pass through the holes
grille mounting hardware access. mounting studs (as shown). The sleeves are used on the drilled in Step 8.
bottom studs only. Remove all other sleeves.

Copyright © 2009 by E&G Classics, Inc.


3
14

13 16

13. Install the supplied small black plastic washers and #8- 14. Install the 1.006” x .189” x .062” black plastic washers 16. Use a grease pencil to mark the areas that need to be
32 ESNA half nuts to the outer studs and completely and #8-32 ESNA half nuts onto the remaining studs and trimmed on the front license plate bracket (as shown).
tighten. DO NOT OVERTIGHTEN or you could damage tighten. DO NOT OVERTIGHTEN or you could damage Use a small disc grinder to remove the section of the
the lower grille surround by indenting it at the stud loca- the lower grille surround by indenting it at the stud loca- bracket (cross hatched areas) that would interfere with
tions. tions. reinstallation.
15. Once the lower grille is installed, remove the 2 x 4 sec-
tions and reinstall the two 10mm bolts removed in Step
9.

Emblem Mounting Plate


2010 Chevrolet Camaro
Hole Location Template
Part # 1412 - 0069 - 10
19
17
18

17. Reinstall the front license plate bracket (if equipped). 18. Cut out and align the supplied templates, taping them in 19. The small template will be used on the verticle grille fins
place. Use an awl or similar pointed tool to make the as well, top and bottom aligned (bottom shown).
centers of the hole locations onto the factory grille.

Copyright © 2009 by E&G Classics, Inc.


4
IMPORTANT

21
20

20. Use a .125” (1/8”) drill bit and drill through the marks 21. Enlarge the holes to 5/16”, then use the drill bit to con- 22. For “RS” & “SS” models: Remove any remaining factory
made in the previous steps. nect the holes, creating a mounting “slot”. Once all the adhesive tape from the back of the factory emblem.
mounting holes have been drilled, blow out the holes Install and trim the supplied .045” x 1” double faced
IMPORTANT: Apply multiple layers of masking tape to the and front of the vehicle to remove any plastic shavings tape to the back of the emblem (“RS” shown).
painted bumper cover at the areas that the factory grille that could get caught between the mesh and factory
will be drilled. Drill carefully and DO NOT ALLOW THE grilles.
DRILL CHUCK TO MAKE CONTACT WITH THE PAINTED
BUMPER COVER !

26
24

25

23. For “RS” & “SS” models: Adhere the emblem to the sup- 25. Prior to grille installation, align and install the emblem 26. Align the mesh and surround into place, making sure all
plied logo backing plate (“SS” shown). assembly onto the mesh grille in the approximate place it studs have passed through the holes drilled in the previ-
24. Install .045 x 1” double faced tape onto the back of the was on the factory grille using the supplied large black ous steps. Install the supplied 5/16” PVC spacers and #8-
emblem mounting plate and remove the liner (where plastic washer, #10 lock washer and a #8-32 hex nut 32 ESNA half nuts. All six (6) studs will require the use of
shown, see arrows). and tighten until the emblem is snug. The tape will keep the supplied spacers. Hand tighten the ESNA nuts only
the emblem from rotating. at this time!

5 Copyright © 2009 by E&G Classics, Inc.


27 29

27. Use cutters to remove the mesh retaining wire ties, then 28. Align the emblem mounting plate over the back of the 29. Using a small flat blade screwdriver, fit the tip down into
tighten the mounting hardware. factory grille emblem, making sure all the factory mount- the small slot cut into the tab (as shown).
ing tabs pass through the slots in the mounting plate.

33

30
31

30. Bend the retaining tabs towards the factory mounting 31. Close up of the retaining tab properly bent to engage 33. Align the emblem assembly into place, making sure all
tabs until they hook underneath, locking the emblem to the factory mounting tab, keeping the emblem tight studs have passed through the holes drilled in the previ-
the mounting plate. against the mounting plate. ous steps. Install the supplied small black plastic washers
32. Bend all remaining tabs to secure the emblem to the and #8-32 ESNA half nuts to secure the emblem assem-
mounting plate (not shown). bly.

Copyright © 2009 by E&G Classics, Inc.


6
34 36

35

34. Apply multiple layers of masking tape to the bumper 35. Push in on the grille surround and install the supplied 36. Remove the protective masking tape from around the
cover at the outer mounting hole locations. Carefully drill #6 x 1/2” countersunk phillips screws but DO NOT mesh grilles. Peel the tape back over itself to minimize
through the outer grille mounting holes using a 1/16” OVERTIGHTEN. Over tightening will strip out the breakage.
drill bit. Use extreme caution and DO NOT LET THE mounting holes!
DRILL CHUCK HIT THE BUMPER COVER or NICK THE
CHROME MESH SURROUND !

37

39

37. Once the internal grille mounting hardware is tight, rein- 38. Install the supplied .045 x .250” double faced tape to the 39. Peel back a small section of the double faced tape liner
stall the hood latch assembly by aligning the assembly to back of the stainless steel overlays as shown. from each piece of double faced tape and fold it over.
the marks made in Step 3 and installing and tightening 40. Carefully align the overlay so that the edges are flush
the factory 13mm hex bolts. with the mesh surround. Once properly aligned, begin
pressing on the overlay while pulling off the remaining
tape liner. Once all the liner has been removed, firmly
press the overlay into place to set the tape.

Copyright © 2009 by E&G Classics, Inc.


7
41

42

41. Peel off the protective liner from the stainless steel over- 42. Reinstall the factory panel removed in Steps 1 & 2. 43. Remove the protective cover from the lower mesh grille
lay and use a mild solvent to remove any glue residue. surround. Use a mild solvent to remove any glue residue
Use alcohol or glass cleaner to remove any solvent from the surround, then use glass cleaner or alcohol to
residue. remove any solvent residue.
44. Finished installation.

WARRANTY INFORMATION:
E&G Classics, Inc. warrants its chrome parts and products to be free from defects in mate-
rial, workmanship or finish for Thirty-Six (36) months from the date of shipment by E&G. This
warranty is limited to the repair or replacement, at E&G Classics option, of the defective part
or product.
To obtain performance under this warranty you must:
1.) Present your E&G unit to an authorized distributor in your area with proof of purchase.
2.) If no distributor is available, contact E&G Classics (address below) for authorization to
return unit.
3.) Returns - All unauthorized returns will be refused. Merchandise approved by E&G for return
must have been purchased within the Thirty-Six (36) months. All returns require an authoriza-
tion number obtained from E&G and the actual return must be accompanied by the written
authorization form filled out completely. All merchandise must be inspected upon receipt and
shortages reported within 48 hours. All merchandise must be in a resalable condition.
Merchandise must be packed carefully in the original packing. If original packing is no longer
usable, repack item(s) comparable to original manner. All returns are subject to a 25% han-
dling charge. Special order items are not returnable. Defective merchandise must have an
explanation of the problem. No credit will be issued unless invoice number and date of pur-
chase has been supplied. Manufacturer shall besole judge of defects in a product.
4.) UPS accounts - All returns must be prepaid. Do not send return shipments freight collect.
Once E&G has made its decision and it is a claim against our warranty policy, E&G will
credit incoming freight on damaged parts.
5.) No discontinued part or parts changed due to body style are returnable.
For Return Authorization, write or telephone: E&G Classics, Inc.,
8910 McGaw Court, Columbia, MD 21045 (410) 381-4900
Attn.: Return Department.
You are responsible for inspecting all packages containing E&G Classics' parts and product
immediately upon their receipt and must file a claim with the carrier for any damage disclosure
by such inspection and notify E&G classics in writing at the above address of any such dam-
age. This warranty does not extend to any of our products which have been subject to mis-
use, neglect, accident or have been altered or repaired in any way. This warranty does not
cover any accidental or consequential damages for any breach of this warranty agreement.
E&G Classics shall have no responsibility for any loss of time, inconvenience, commercial loss
or consequential damage, nor shall E&G be liable for any injury or damage to persons or prop-
erty by reason of any defect in material, workmanship or finish of its parts or products. This
warranty gives you specific legal rights and you may also have other rights which may vary
from state to state.

Copyright © 2009 by E&G Classics, Inc.


9

Das könnte Ihnen auch gefallen