Beruflich Dokumente
Kultur Dokumente
Manual
SERVICE
AIR CONDITIONER CONTENTS
1. Product Specifications
2. Operating Instructions
7. PCB Diagram
8. Wiring Diagram
9. Schematic Diagram
DB98_15968A(1)_1 11/25/03 1:51 PM Page 1
1. Product Specifications
1-1 Table
Samsung Electronics 1
DB98_15968A(1)_1 11/25/03 1:51 PM Page 2
■ 18K BTU
10
32.4/24.0
28.8/21.0
27.0/19.0
8
24.0/17.0
21.5/15.0
6
20 25 30 35 40 45
■ 24K BTU
10
32.4/24.0
30.6/22.5
28.8/21.0
27.0/19.0
Indoor inlet air D.B. temp(˚C)
9
Low pressure(kg/cm2G)
24.0/17.0
21.5/15.0
6
20 25 30 35 40 45
2 Samsung Electronics
DB98_15968A(1)_1 11/25/03 1:51 PM Page 3
2. Operating Instructions
: Dry Mode
Swing button.
6
It adjusts the airflow to upward and downward.
On Timer button.
7 The On Timer enables you to switch on the air conditioner automatically after a given period
of time that is from 30 minutes to 24 hours.
To cancel, press the (Set/Cancel) button.
Samsung Electronics 3
DB98_15968A(1)_1 11/25/03 1:51 PM Page 4
Operating Instructions
1. AUTO MODE : In this mode, operation mode(COOL, 4. DRY MODE : Has 3 states, each determined by room
HEAT) is selected automatically by the room temperature temperature.
of initial operation. The unit operates in DRY mode.
*Compressor ON/OFF Time is controlled compulsorily
Room Temp Operation Type
(can not set up the fan speed, always breeze).
Tr≥ 21°C+∆T Cool Operation (Set Temp:24˚C+∆T) *Protective function : Low temperature release.
21°C +∆T>Tr Heat Operation (Set Temp:22˚C+∆T) (Prevention against freeze)
∆T= -1°C, -2°C, 0°C, +1°C, +2°C 5. TURBO MODE : This mode is available in AUTO, COOL,
∆T is controlled by setting temperature up/down key of HEAT, DRY, FAN MODE.
remote control When this button is pressed at first, the air conditioner is
operated “powerful” state for 30 minutes regardless of the
2. COOL MODE : The unit operates according to the set temperature, room temperature.
difference between the setting and room temperature. When this button is pressed again, or when the operating
(18°C~30°C) time is 30 minutes, turbo operation mode is canceled
and returned to the previous mode.
3. HEAT MODE : The unit operates according to the *But, if you press the TURBO button in DRY or FAN
difference between the setting and room temperature. mode that is changed with AUTO mode automatically.
(16°C~30°C)
*Prevention against cold wind : In order to prevent the 6. SLEEP MODE : Sleep mode is available only in COOL or
cool air from flowing out at the heat mode, the indoor fan HEAT mode.
does not operate or operates very slowly in the The operation will stop after 6 hours.
following cases. At this time, the indoor heat exchanger *In COOL mode : The setting temperature is automatical-
will be preheating. ly raised by 1°C each 1hour When the temperature
- For 3~5 minutes after the initial operation has been raised by total of 2°C, that temperature is
- For deicing operation maintained.
- The operation of an indoor fan in accordance with the *In HEAT mode : The setting temperature is automatical-
temperature of an indoor heat exchanger ly dropped by 1°C each 1hour.
When the temperature has been dropped by total of
The temperature of
Indoor fan speed 2°C, that temperature is maintained.
indoor heat exchanger
4 Samsung Electronics
DB98_15968A(1)_1 11/25/03 1:51 PM Page 5
Operating Instructions
Samsung Electronics 5
DB98_15968A(1)_1 11/25/03 1:51 PM Page 6
2-2 Installation
2-2-1 Selecting Area for Installation 3. Make sure that you install the outdoor unit in area provid-
ing good ventilation and which is not dusty. It must not
Select an area for installation that is suitable to the cus- be blocked by any obstacle affecting the airflow near the
tomer's needs. air inlet and the air outlet.
4. Make sure that you install the outdoor unit in area free
2-2-1(a) Indoor Unit from animals or plants.
1. Make sure that you install the indoor unit in an area pro- 5. Make sure that you install the outdoor unit in area not
viding good ventilation. It must not be blocked by an blocking the traffic.
obstacle affecting the airflow near the air inlet and the air
outlet. 6. Make sure that you install the outdoor unit in area easy to
drain condensed water from the indoor unit.
2. Make sure that you install the indoor unit in an area
allowing good air handling and endurance of vibration of 7. Make sure that you install the outdoor unit in area which
the indoor unit. provides easy connection within the maximum allowable
length of a coolant pipe(18✳✳:15meters, 24✳✳:20meters).
3. Make sure that you install the indoor unit in an area
where there is no source of heat or vapor nearby.
Note
1. Add (18✳✳: 20g, 24✳✳: 30g) of refrigerant (R410a) for
4. Make sure that you install the indoor unit in an area from
every 1 meter if the pipe length exceeds the standard
which hot or cool air is spread evenly in a room. pipe length of 7.5 meters.
2. Maintain a height between the indoor and outdoor units
5. Make sure that you install the indoor unit in an area away of less than 8 meters.
from TVs, audio units, cordless phones, fluorescent light-
ing fixtures and other electrical appliances (at least 1
meter). 8. Make sure that you install the outdoor unit in an area
which is large enough to accommodate the measure-
6. Make sure that you install the indoor unit in an area ments
which provides easy pipe connection with the outdoor
unit, and easy drainage for condensed water.
2-2-1(c) Remote Control Unit
7. Make sure that you install the indoor unit in an area
which is large enough to accommodate the measure- 1. Make sure that you install the remote control unit in an
ments shown in figure on the next page. area free from obstacles such as curtains etc, which may
block signals from the remote control unit.
2-2-1(b) Outdoor Unit 2. Make sure that you install the remote control unit in an
area not exposed to direct sunlight, and where there is no
1. Make sure that you install the outdoor unit in area not source of heat.
exposed to the rain or direct sun light.
(Install a separate sunblind if exposed to direct sun light.) 3. Make sure that you install the remote control unit in an
area away from TVs, audio units, cordless phones, fluo-
2. Make sure that you install the outdoor unit in area allow- rescent lighting fixtures and other electrical appliances (at
ing good air moment, not amplifying noise or vibration, least 1 meter).
especially to avoid disturbing neighbors. (Fix the unit
firmly if it is mounted in a high place.)
• It is harmful to the air conditioner if it is used in the following environments: greasy areas (including areas near
machines), salty areas such as coast areas, areas where sulfuric gas is present such as hot spring areas.
Contact your dealer for advice.
6 Samsung Electronics
DB98_15968A(1)_1 11/25/03 1:52 PM Page 7
Samsung Electronics 7
DB98_15968A(1)_1 11/25/03 1:52 PM Page 8
8 Samsung Electronics
DB98_15968A(1)_1 11/25/03 1:52 PM Page 9
Samsung Electronics 9
DB98_15968A(1)_1 11/25/03 1:52 PM Page 10
10 Samsung Electronics
DB98_15968A(1)_1 11/25/03 1:52 PM Page 11
Capillary tube
T1 2-Way valve
Liquid side
Propeller fan
Cross fan
Heat Heat
exchanger exchanger
(Evaporator) (Evaporator)
T2
Gas side
Heating
Compressor
Gas leak check point
Samsung Electronics 11
DB98_15968A(1)_1 11/25/03 1:52 PM Page 12
Step 2 : Enter the Option Setup mode and select your option according to the following procedure.
1
The default value is .
Otherwise, push the button to .
Every time you push the button, the display panel reads or
repeatedly.
1 2
Push the button to set the display panel to .
2
Every time you push the button, the display panel reads
3 ... repeatedly.
4 3
Push the button to set the display panel to .
Every time you push the button, the display panel reads
5 ... repeatedly.
6
4
Push the button to set the display panel to .
Every time you push the button, the display panel reads
... repeatedly.
5
Push the button to set the display panel to .
Every time you push the button, the display panel reads
... repeatedly.
12 Samsung Electronics
DB98_15968A(1)_1 11/25/03 1:52 PM Page 13
7
Press button, then the default value is .
8
Push the button to set the display panel to .
7
Every time you push the button, the display panel reads
8 ... repeatedly.
9
9
Push the button to set the display panel to .
10 Every time you push the button, the display panel reads
... repeatedly.
11
12
10
Push the button to set the display panel to .
Every time you push the button, the display panel reads
... repeatedly.
11
Push the button to set the display panel to .
Every time you push the button, the display panel reads
... repeatedly.
12
Push the button to set the display panel to .
✳ Setting is not required if you must
Every time you push the button, the display panel reads
a value which has a default. ... repeatedly.
Step 3 : Upon completion of the selection, check you made right selections.
Press the Mode Selection key, to set the display part to and check the display part.
The display part shows .
Press the Mode Selection key, to set the display part to and check the display part.
The display part shows .
Samsung Electronics 13
DB98_15968A(1)_1 11/25/03 1:52 PM Page 14
■ OPTION ITEMS
REMOCON
SEG1 SEG2 SEG3 SEG4 SEG5 SEG6 SEG7 SEG8 SEG9 SEG10 SEG11 SEG12
MODEL
SH18AS0 0 8 5 1 1 5 1 d A 3 5 1
SH24AS6 0 8 5 4 1 4 1 d A 3 8 4
14 Samsung Electronics
DB98_15968A(1)_1 11/25/03 1:52 PM Page 15
MEMO
Samsung Electronics 15
DB98_15968A(1)_2 11/25/03 1:52 PM Page 16
15
10
18 14
16
19
16-6
16-4
6 16-1
13 16-3
7
3
11
16-2
8
16-5
12
17
1 1-4
9
1-2 1-1
2
1-3
5
You can search for the updated part code
4 number through the ITSELF.
URL : http://itself.sec.samsung.co.kr
16 Samsung Electronics
DB98_15968A(1)_2 11/25/03 1:52 PM Page 17
■ Parts List
Q'TY
No. Code No. Description Specification Remark
SH18AS0 SH24AS6
8 DB31-10151C MOTOR-FAN IN - 1 1
11 DB61-01136A HOLDER-MOTOR PP 1 1
Samsung Electronics 17
DB98_15968A(1)_2 11/25/03 1:52 PM Page 18
■ 24K BTU
13
21
12
8
19
10
7 11
14
17
15-3
15-4
6
15
18-6
15-2
5 18-4
15-1
18
18-5
18-1 18-3
18-2
1
16
4
2
16-1
3
20-1 20-3
20-2 20-4
18 Samsung Electronics
DB98_15968A(1)_2 11/25/03 1:52 PM Page 19
■ Parts List
Q'TY
No. Code No. Description Specification Remark
SH24AS6X
2 DB63-00831A GUARD-FAN PP 1
Samsung Electronics 19
DB98_15968A(1)_2 11/25/03 1:52 PM Page 20
■ 18K BTU
13
21
12
19
10
11
9
14 8
15-3
15-4
17
7 15
15-2
15-1
18-2 18
5
18-1
6
18-3
18-6
16 18-5
1 18-4
16-1
20-1 20-3
20-2 20-4
20 Samsung Electronics
DB98_15968A(1)_2 11/25/03 1:52 PM Page 21
■ Parts List
Q'TY
No. Code No. Description Specification Remark
SH18AS0X
Samsung Electronics 21
DB98_15968A(1)_2 11/25/03 1:52 PM Page 22
22 Samsung Electronics
DB98_15968A(1)_2 11/25/03 1:52 PM Page 23
■ Parts List
Q'TY
No. Code No. Description Specification Remark
SH18AS0 SH24AS6
21 - POWER CORD - - -
Samsung Electronics 23
DB98_15968A(1)_2 11/25/03 1:52 PM Page 24
7. PCB Diagram
■ TOP
24 Samsung Electronics
DB98_15968A(1)_2 11/25/03 1:52 PM Page 25
PCB Diagram
■ Parts List
Location No. Description Specification Q'TY Remark
TP,4x9mm
Samsung Electronics 25
DB98_15968A(1)_2 11/25/03 1:52 PM Page 26
PCB Diagram
■ BOTTOM
■ Parts List
Location No. Description Specification Q'TY Remark
26 Samsung Electronics
DB98_15968A(1)_2 11/25/03 1:52 PM Page 27
■ TOP
OPT04
ASS’Y PCB OPT01 OPT02 OPT03 OPT05 OPT06 OPT07 OPT08
(CN94)
DB93-01325A SMW200-09(WHT) SMW200-05(WHT)
DB93-01325B SMW200-12(WHT) SMW200-05(WHT)
DB93-01325C SMW200-12(WHT) SMW200-05(WHT)
DB93-01325E SMW200-09(WHT) SMW200-06(WHT)
DB93-01325F SMW200-12(WHT) SMW200-06(WHT)
DB93-01325G SMW200-12(WHT) SMW200-06(WHT)
DB93-01325J SMW200-12(WHT) SMW200-05(WHT)
DB93-01325K SMW200-12(WHT) SMW200-05(WHT)
DB93-01325L SMW200-12(WHT) SMW200-06(WHT)
■ Parts List
Location No. Description Specification Q'TY Remark
Samsung Electronics 27
DB98_15968A(1)_2 11/25/03 1:52 PM Page 28
PCB Diagram
■ BOTTOM
■ Parts List
Location No. Description Specification Q'TY Remark
28 Samsung Electronics
DB98_15968A(1)_2 11/25/03 1:52 PM Page 29
■ Parts List
No. Description Specification Q'TY Remark
Samsung Electronics 29
DB98_15968A(1)_2 11/25/03 1:52 PM Page 30
■ Parts List
No. Description Specification Q'TY Remark
3 C-CERAMIC, MLC-AXIAL 1nF, 10%, 50V, Y5P, TP, 1.9 x 3.5, - 1 SNA
30 Samsung Electronics
DB98_15968A(1)_2 11/25/03 1:52 PM Page 31
MEMO
Samsung Electronics 31
DB98_15968A(1)_2 11/25/03 1:52 PM Page 32
8. Wiring Diagram
Code No : DB98-06958A
32 Samsung Electronics
DB98_15968A(1)_2 11/25/03 1:52 PM Page 33
■ SH18AS0X
Code No : DB98-15862A
■ SH24AS6X
Code No : DB98-15985A
Samsung Electronics 33
DB98_15968A(1)_2 11/25/03 1:52 PM Page 34
9. Schematic Diagram
34 Samsung Electronics
DB98_15968A(1)_2 11/25/03 1:52 PM Page 35
Schematic Diagram
Samsung Electronics 35
DB98_15968A(1)_2 11/25/03 1:52 PM Page 36
MEMO
36 Samsung Electronics
DB98_15968A(1)_co 11/25/03 1:53 PM Page 2
ELECTRONICS
This Service Manual is a property of Samsung Electronics Co., Ltd. © Samsung Electronics Co., Ltd. Dec. 2003.
Any unauthorized use of Manual can be punished under applicable Printed in Korea.
International and/or domestic law. Code No. DB98-15968A(1)