Beruflich Dokumente
Kultur Dokumente
Morstar offers both porcelain and polymeric cutouts for systems rated at 15kV and 27kV, the
Polymeric insulator is Silicon Rubber or HDPE for polymeric cutouts. Morstar Cutouts meet and or exceed
all applicable ANSI performance requirements with testing performed at an accredited independent
laboratory.
Morstar cutouts are manufactured with the following features standard: All electrical contacts are
silver plated. Tin plated parallel grooves are standard. Groove 1 handles #6 solid through #6 tranded.
Groove 2 handles #2 solid through 25 mil or 4/0 ACSR. Heavy-duty galvanized sleet shield, arcing horns
and NEMA Type B brackets are standard. Polymeric cutouts are manufactured out of 100% silicone
rubber, not a polymer alloy. All mechanical fasteners are manufactured from 304 stainless steel.
A. FUSE CUTOUT
*Hinge : Basic material is stainless. But upon user's request, can be replace bronze casting.
1- Parallel Connector – Made of tinned bronze for cables from 8 AWG to 4/0 ACSR. To ease the
connection, it can accommodates two conductors with different size in a single connector. Also available
in other models.
2- Upper Contact – Silver to silver; stainless steel springs offers high contact pressure
3- Attachment Hooks – Used as tool support for energized opening as well as to guide the fuse tube
during closing.
4- Fuse Tube – Vulcanized fiber covered with fiberglass and painted with a special UV resistant epoxy.
5- Lower Contacts – Silver to silver; non ferrous springs offer high contact pressure
6- Toggle-joint – Stainless steel construction.
934D4 Đường D KCN Cát Lái P. Thạnh Mỹ Lợi, Q. 2, tp HCM Tel: 028 37421888 Fax: 028 37423783 Website: www.morstar.vn
Morstar has a policy of continuous product improvement, we reserve the right to change design and specifications without notice. Page 1 of 10
7- Flipper – Stainless steel construction; in conjunction with the toggle joint allows, especially during
closing, the fuse link to be subject to traction forces of over 3 Kgf; it also allows for high speed fuse link
separation
8- Trunnion – Silver plated high strength cast bronze construction; it assists the fuse tube alignment
during closing.
9- Insulator – High strength porcelain in accordance with ANSI, IEC, or made of an ECR fiberglass core
enveloped in a silicone rubber.
CHARACTERISTIC
SPECIFICATIONS
Porcelain
Arc
Voltage Rating kV Continuous Interruption Leakage Shipping
Part nbr Shortening
current level Distance Weight
Nom. Max. Bil Rod
MSCO-P111 14.4 15 110 100AMP 10kA ASYM) 9.64”-245mm 6.87kg No
MSCO-P211 14.4 15 110 200AMP 12kA(ASYM) 9.64”-245mm 7.32kg Yes
MSCO-P311 14.4 15 110 300AMP 12kA(ASYM) 9.64”-245mm 7.59kg Solid blade
MSCO-P122 25 27 125 100AMP 12kA ASYM) 13.7”-350mm 8.82kg Yes
MSCO-P222 25 27 125 200AMP 10kA(ASYM) 13.7”-350mm 9.38kg Yes
MSCO-P322 25 27 125 300AMP 12kA(ASYM) 13.7”-350mm 9.52kg Solid blade
MSCO-P125 25 27 150 100AMP 12kA ASYM) 18.1”-460mm 11.28kg Yes
MSCO-P225 25 27 150 200AMP 10kA(ASYM) 18.1”-460mm 12.53kg Yes
MSCO-P325 25 27 150 300AMP 12kA(ASYM) 18.1”-460mm 12.84kg Solid blade
MSCO-P127 25 36 170 100AMP 12kA ASYM) 28.3”-720mm 14.69kg Yes
MSCO-P227 25 36 170 200AMP 10kA(ASYM) 28.3”-720mm 15.01kg Yes
MSCO-P327 25 36 170 300AMP 12kA(ASYM) 28.3”-720mm 15.91kg Solid blade
+Cần ngắt của cầu chì tự rơi có thể được biến đổi thành cầu dao 1 pha tới 300 A bằng cách đơn giản thay đổi ống cầu chì bằng
một cần đóng cắt bằng đồng.
+The fuse cutout type MSCO may be transformed into a DICONNECT up to 300 A, by simply changing the fuse tube for an
electrolytic copper blade. (See Figure 1)
934D4 Đường D KCN Cát Lái P. Thạnh Mỹ Lợi, Q. 2, tp HCM Tel: 028 37421888 Fax: 028 37423783 Website: www.morstar.vn
Morstar has a policy of continuous product improvement, we reserve the right to change design and specifications without notice. Page 2 of 10
STYPES (Porcerlain)
Polymeric
Arc
Voltage Rating kV Continuous Interruption Leakage Shipping
Part nbr Shortening
current level Distance Weight
Nom. Max. Bil Rod
MSCO-S111 14.4 15 110 100AMP 10kA ASYM) 15.2”-385mm 3.165kg No
MSCO-S211 14.4 15 110 200AMP 12kA(ASYM) 15.2”-385mm 3.457kg Yes
MSCO-S311 14.4 15 110 300AMP 12kA(ASYM) 15.2”-385mm 3.675kg Solid blade
MSCO-S125 25 27 150 100AMP 12kA ASYM) 24.4”-660mm 3.238kg Yes
MSCO-S225 25 27 150 200AMP 10kA(ASYM) 24.4”-660mm 3.618kg Yes
MSCO-S325 25 27 150 300AMP 12kA(ASYM) 24.4”-660mm 3.936kg Solid blade
MSCO-S127 25 36 170 100AMP 12kA ASYM) 32.6”-830mm 6.015kg Yes
MSCO-S227 25 36 170 200AMP 10kA(ASYM) 32.6”- 830mm 6.330kg Yes
MSCO-S327 25 36 170 300AMP 12kA(ASYM) 32.6”- 830mm 6.605kg Solid blade
934D4 Đường D KCN Cát Lái P. Thạnh Mỹ Lợi, Q. 2, tp HCM Tel: 028 37421888 Fax: 028 37423783 Website: www.morstar.vn
Morstar has a policy of continuous product improvement, we reserve the right to change design and specifications without notice. Page 3 of 10
STYPES (Polymeric)
Specially designed to protect transformers, capacitor banks, cubicles, lines and branches.
With this arc chute , the versatility of the Morstar protection equipment is enhanced, allowing on-load openings without the
need of special tools for its operation.
Its characteristics are similar to a type Morstar Standard Cutout, which provides protection from short-circuit and overloads
that just melt the fuselink through the maximum interrupt capacity of the fuseholder.
The Loadbreak opening device enables the lineman to interrupt load current by means of a simple operation with a hookstick.
To break the current, the lineman inserts a hookstick into the operating ring and rapidly opens the device.
Its operation is independent of the lineman’s operating speed for the current is transferred from the top contact of the cutout
to a mechanism with a spring-loaded stainless steel blade during the opening, where the arc is elongated, cools down and
extinguishes itself.
It may be applied on any three-phase system voltage rated at or below the maximum operational rating of the cutout.
This equipment was developed for switching currents up to 300A, by means of an electrolytic copper blade.
The Morstar fuse cutouts designs are tested in accordance with TCVN, ANSI and IEC standards.
934D4 Đường D KCN Cát Lái P. Thạnh Mỹ Lợi, Q. 2, tp HCM Tel: 028 37421888 Fax: 028 37423783 Website: www.morstar.vn
Morstar has a policy of continuous product improvement, we reserve the right to change design and specifications without notice. Page 4 of 10
CHARACTERISTIC
SPECIFICATIONS
Porcelain
Arc
Voltage Rating kV Continuous Interruption Leakage Shipping
Part nbr Shortening
current level Distance Weight
Nom. Max. Bil Rod
MSCO-LP11 14.4 15 110 100AMP 16kA ASYM) 9.4”-240mm 15.432lb Yes
MSCO-LP21 14.4 15 110 200AMP 12kA(ASYM) 9.4”-240mm 16.975lb Yes
MSCO-LP31 14.4 15 110 300AMP Solid blade 9.4”-240mm 15.630lb Disconnect
MSCO-LP12 25 27 125 100AMP 12kA ASYM) 12.6”-340mm 18.188lb Yes
MSCO-LP22 25 27 125 200AMP 10kA(ASYM) 12.6”-340mm 19.510lb Yes
MSCO-LP32 25 27 125 300AMP Solid blade 12.6”-340mm 18.298lb Disconnect
MSCO-LP15 25 27 150 100AMP 12kA ASYM) 17”-450mm 22.443lb Yes
MSCO-LP25 25 27 150 200AMP 10kA(ASYM) 17”-450mm 23.765lb Yes
934D4 Đường D KCN Cát Lái P. Thạnh Mỹ Lợi, Q. 2, tp HCM Tel: 028 37421888 Fax: 028 37423783 Website: www.morstar.vn
Morstar has a policy of continuous product improvement, we reserve the right to change design and specifications without notice. Page 5 of 10
MSCO-LP35 25 27 150 300AMP Solid blade 17”-450mm 22.575lb Disconnect
MSCO-LP17 25 36 170 100AMP 12kA ASYM) 26”-680mm 27.844lb Yes
MSCO-LP27 25 36 170 200AMP 10kA(ASYM) 26”-680mm 29.167lb Yes
MSCO-LP37 25 36 170 300AMP Solid blade 26”-680mm 28.020lb Disconnect
+Cần ngắt của cầu chì tự rơi có thể được biến đổi thành cầu dao 1 pha tới 300 A bằng cách đơn giản thay đổi ống cầu chì bằng
một cần đóng cắt bằng đồng.
+The fuse cutout type MSCO may be transformed into a DICONNECT up to 300 A, by simply changing the fuse tube for an
electrolytic copper blade.
STYPES (Porcerlain)
934D4 Đường D KCN Cát Lái P. Thạnh Mỹ Lợi, Q. 2, tp HCM Tel: 028 37421888 Fax: 028 37423783 Website: www.morstar.vn
Morstar has a policy of continuous product improvement, we reserve the right to change design and specifications without notice. Page 6 of 10
Polymeric
Arc
Voltage Rating kV Continuous Interruption Leakage Shipping
Part nbr Shortening
current level Distance Weight
Nom. Max. Bil Rod
MSCO-LS11 14.4 15 110 100AMP 16kA ASYM) 15.2”-385mm 10.340lb Yes
MSCO-LS21 14.4 15 110 200AMP 12kA(ASYM) 15.2”-385mm 10.516lb Yes
MSCO-LS31 14.4 15 110 300AMP Solid blade 15.2”-385mm 10.494lb Disconnect
MSCO-LS15 25 27 150 100AMP 12kA ASYM) 19.3”-660mm 11.023lb Yes
MSCO-LS25 25 27 150 200AMP 10kA(ASYM) 19.3”-660mm 12.786lb Yes
MSCO-LS35 25 27 150 300AMP Solid blade 19.3”-660mm 11.243lb Disconnect
MSCO-LS17 25 36 170 100AMP 12kA ASYM) 30”-762mm 12.037lb Yes
MSCO-LS27 25 36 170 200AMP 10kA(ASYM) 30”-762mm 13.360lb Yes
MSCO-LS37 25 36 170 300AMP Solid blade 30”-762mm 12.346lb Disconnect
STYPES (Polymeric)
934D4 Đường D KCN Cát Lái P. Thạnh Mỹ Lợi, Q. 2, tp HCM Tel: 028 37421888 Fax: 028 37423783 Website: www.morstar.vn
Morstar has a policy of continuous product improvement, we reserve the right to change design and specifications without notice. Page 7 of 10
C. TEMPORARY CUTOUT 27Kv
Fuse Tube 100 Amps Solid Blade 300 Amps Temporary Load Disconnect
934D4 Đường D KCN Cát Lái P. Thạnh Mỹ Lợi, Q. 2, tp HCM Tel: 028 37421888 Fax: 028 37423783 Website: www.morstar.vn
Morstar has a policy of continuous product improvement, we reserve the right to change design and specifications without notice. Page 8 of 10
operation is independent of the disconnect stick speed. To provide a clearly visible break,
the disconnect blade hangs in approximately a vertical position.
D. DISCONNECTING BLADE
The Disconnect Blade is indicated for use with the Morstar cutout. Replaces the fuse
holder into a disconnect switch. Permanent 300A current carrying capacity.
It consists of a copper tube of high conductivity, with contacts in silver bronze and with eye
for operation with Manouver.
Manufactured for the 15kV, 27kV and 38kV voltages and use with the "Morstar Cutout" ,
this model allows the opening under load with the use of the opening tool under load.
934D4 Đường D KCN Cát Lái P. Thạnh Mỹ Lợi, Q. 2, tp HCM Tel: 028 37421888 Fax: 028 37423783 Website: www.morstar.vn
Morstar has a policy of continuous product improvement, we reserve the right to change design and specifications without notice. Page 9 of 10
E. MOUNTING BRACKET
The L mounting bracket is used to attach Fuse keys and lightning rods. It is made on 2
sheet thicknesses:
A NEMA - 5/16 "(7.93 mm);
B NEMA - 3/8 "(9.52 mm);
Its manufacturing in 1010/1020 steel ensures its performance by handling and efforts
without losing its characteristics and its hot galvanized finishing states its durability.
CHARACTERISTICS
+ Made of 1010/1020steel.
+ Hot galvanized finishing.
+ High mechanical strength
934D4 Đường D KCN Cát Lái P. Thạnh Mỹ Lợi, Q. 2, tp HCM Tel: 028 37421888 Fax: 028 37423783 Website: www.morstar.vn
Morstar has a policy of continuous product improvement, we reserve the right to change design and specifications without notice. Page 10 of 10