Sie sind auf Seite 1von 12

® TOTALINE® COPPER ELBOWS

TOTALINE® COPPER ELBOWS


105 series 107 series 107L2 series 107l series
long radius long radius long radius long radius
45° street elbow 90° reducing elbow 90° street elbow 90° elbow

Copper
to Copper

Fitting to
Fitting Copper
Fitting
to Copper to Copper

P774 P775
P776 P777

O.D. SIZE BOX MASTER APPROX.


P/N
(in.) QTY. PACK NET WT.
O.D. SIZE BOX MASTER APPROX.
P/N 107L2 SERIES —
(in.) QTY. PACK NET WT.
105 SERIES — 90° STREET ELBOW, Long Radius
45° STREET ELBOW, Long Radius 3/8 50 1000 .016 P805-W2809
2-1/8 5 40 1.010 P805-W2659 1/2 50 500 .030 P805-W2817
5/8 100 1000 .050 P805-W2822
107R SERIES —
3/4 25 250 .080 P805-W2828
90° REDUCING ELBOW, Long Radius
7/8 25 250 .120 P805-W2834
1/2 x 3/8 50 1000 .026 P805-W2719
1-1/8 10 100 .210 P805-W2847
5/8 x 1/2 50 500 .040 P805-W2723
1-3/8 10 80 .390 P805-W2350
7/8 x 3/4 25 250 .120 P805-W2735
1-5/8 10 80 .580 P805-W2355
7/8 x 5/8 50 500 .090 P805-W2736
2-1/8 5 40 1.010 P805-W2359
7/8 x 1/2 50 500 .070 P805-W2737
2-5/8 1 10 1.670 P805-W2363
1-1/8 x 7/8 25 250 .170 P805-W2749
3-1/8 1 8 2.510 P805-W2368
1-3/8 x 1-1/8 10 100 .310 P805-W2756
3-5/8 1 8 3.700 P805-W2393
1-5/8 x 1-3/8 5 50 .470 P805-W2064
4-1/8 1 1 5.760 P805-W2395
1-5/8 x 1-1/8 5 50 .350 P805-W2065
2-1/8 x 1-5/8 5 40 .770 P805-W2073
107L SERIES — 90° ELBOW, Long Radius
2-5/8 x 2-1/8 5 50 .350 P805-W2083 1/4 50 1000 .008 P805-W2715
5/16 50 1000 .013 P805-W2710
3/8 50 1000 .016 P805-W2716
1/2 50 500 .030 P805-W2717
5/8 100 1000 .060 P805-W2722
3/4 25 250 .080 P805-W2728
7/8 25 250 .120 P805-W2734
1-1/8 10 100 .210 P805-W2747
1-3/8 10 80 .390 P805-W2055
1-5/8 10 80 .580 P805-W2063
2-1/8 5 40 1.020 P805-W2072
2-5/8 1 10 1.660 P805-W2082
3-1/8 1 8 2.520 P805-W2092
3-5/8 1 8 3.700 P805-W2093
4-1/8 1 1 5.700 P805-W2095
ELBOWS CONTINUED

NOTE: Order Totaline Copper Fittings by RCD Part Number and Model Series Number.

613
TOTALINE® COPPER ELBOWS
TOTALINE® COPPER ELBOWS
105c series 107cr series 107c2 series
short radius short radius 90° short radius 90°
90° elbow reducing elbow reducing elbow

Copper
to Copper

Fitting
Fitting
to Fitting
to Copper
P781
P780
P782

O.D. SIZE BOX MASTER APPROX. O.D. SIZE BOX MASTER APPROX.
P/N P/N
(in.) QTY. PACK NET WT. (in.) QTY. PACK NET WT.
1062WROT SERIES — 107CR SERIES —
45° STREET ELBOW, Long Radius 90° REDUCING ELBOW, Short Radius
3/8 50 1000 .011 P805-W3312 1/2 x 3/8 50 1000 .026 P805-W2019
1/2 50 1000 .020 P805-W3321 5/8 x 1/2 50 500 .040 P805-W2023
5/8 100 1000 .030 P805-W3326 5/8 x 3/8 50 500 .030 P805-W2025
3/4 25 250 .060 P805-W3330 3/4 x 5/8 25 250 .080 P805-W2029
7/8 50 500 .080 P805-W3334 7/8 x 3/4 25 500 .026 P805-W2035
1-1/8 25 250 .150 P805-W3344 7/8 x 5/8 50 500 .080 P805-W2036
1-3/8 25 200 .240 P805-W3350 1-1/8 x 5/8 25 250 .120 P805-W2051
1-5/8 20 160 .340 P805-W3355 1-1/8 x 7/8 25 250 .150 P805-W2049
2-1/8 10 80 .630 P805-W3359 1-3/8 x 1-1/8 10 100 .230 P805-W2056
2-5/8 5 40 .980 P805-W3363 1-5/8 x 1-3/8 10 100 .340 P805-W2077
4-1/8 1 8 3.200 P805-W3373 2-1/8 x 1-5/8 5 40 .600 P805-W2078
105C SERIES — 2-5/8 x 2-1/8 5 40 1.060 P805-25S21S
90° STREET ELBOW, Short Radius 107C2 SERIES —
3/8 25 500 .012 P805-W2612 90° STREET ELBOW, Short Radius
5/8 25 500 .050 P805-W2626 1/4 50 1000 .006 P805-W2305
3/4 10 200 .070 P805-W105C 3/4 3/8 50 1000 .012 P805-W2312
7/8 25 250 .100 P805-W2634 1/2 50 1000 .024 P805-W2321
1-1/8 10 100 .180 P805-W2644 5/8 100 1000 .050 P805-W2326
1-3/8 5 50 .280 P805-W2684 3/4 25 250 .060 P805-W2330
7/8 50 500 .100 P805-W2334
1-1/8 25 250 .180 P805-W2344
1-3/8 25 200 .280 P805-W2384
1-5/8 20 120 .390 P805-W2385
2-1/8 10 80 .760 P805-W2386
2-5/8 5 40 1.180 P805-W2387
3-1/8 3 25 1.860 P805-W2388
3-5/8 1 8 2.620 P805-W2389
4-1/8 1 8 4.200 P805-W2390
ELBOWS CONTINUED

NOTE: Order Totaline Copper Fittings by Part Number and Model Series Number.

614
TOTALINE® COPPER ELBOWS & REDUCING TEES
TOTALINE® COPPER ELBOWS & REDUCING TEES
1112 SERIES 111 SERIES 111R, RR or BH SERIES
STREET TE TEE REDUCING TEE

P785 P786
P784

Copper to Fitting to Copper Copper to Copper to Copper Copper to Copper to Copper

*
O.D. SIZE BOX MASTER APPROX. O.D. SIZE BOX MASTER APPROX.
P/N P/N
(in.) QTY. PACK NET WT. (in.) QTY. PACK NET WT.
1112 SERIES — STREET TEE 111 R, RR or BH SERIES* — REDUCING TEE
5/2 50 500 .068 P805-W1112 5/8 1/4 x 1/4 x 3/16 50 1000 .015 P805-W40308
7/8 25 250 .174 P805-W1112 7/8 1/4 x 1/4 x 3/8 50 1000 .028 P805-W40368
111 SERIES — TEE 3/8 x 1/4 x 1/4 50 1000 .028 P805-W40332
3/16 50 1000 .009 P805-W40302 3/8 x 1/4 x 3/8 50 1000 .028 P805-W40330
1/4 50 1000 .015 P805-W40306 3/8 x 3/8 x 1/2 50 500 .047 P805-W4005
5/16 50 1000 .020 P805-W40313 3/8 x 3/8 x 1/4 50 1000 .028 P805-W40324
3/8 50 1000 .028 P805-W4000 3/8 x 3/8 x 5/8 50 500 .063 P805-W4016
1/2 50 500 .047 P805-W4001 3/8 x 5/16 x 1/4 P805-6S5S4S
5/8 50 500 .050 P805-W4006 3/16 x 3/16 x 1/4 P805-3S3S4S
3/4 25 250 .100 P805-W4017 5/16 x 1/4 x 1/4 50 1000 .020 P805-5S4S4S
7/8 25 250 .160 P805-W4031 5/16 x 5/16 x 1/4 50 1000 .020 P805-5S5S4S
1-1/8 10 100 .330 P805-W4048
1-3/8 5 50 .460 P805-W4068
1-5/8 5 50 .710 P805-W4084 O.D. SIZE BOX MASTER APPROX.
P/N
2-1/8 5 40 1.290 P805-W40102 (in.) QTY. PACK NET WT.
2-5/8 1 10 1.900 P805-W40123 1/2 x 1/2 x 1/4 50 500 .047 P805-40350
3-1/8 1 10 2.750 P805-W40152 1/2 x 1/2 x 3/8 50 500 .047 P805-4002
3-5/8 1 8 4.170 P805-W40190 1/2 x 1/2 x 5/8 50 500 .063 P805-W4015
4-1/8 1 8 6.620 P805-W40200 1/2 x 1/4 x 1/2 50 500 .047 P805-W40363
1/2 x 3/8 x 1/2 50 500 .047 P805-W4003
1/2 x 3/8 x 1/4 50 500 .047 P805-W40358
1/2 x 3/8 x 3/8 50 500 .047 P805-W4004
1/2 x 3/8 x 5/8 50 500 .063 P805-40355
ELBOWS CONTINUED

*111R — Reducing on Outlet.


111RR — Reducing on Run.
111BH — Large Diameter Outlet.

NOTE: Order Totaline Copper Fittings by Part Number and Model Series Number.

615
TOTALINE® COPPER ELBOWS & REDUCING TEES
TOTALINE® COPPER ELBOWS & REDUCING TEES

O.D. SIZE BOX MASTER APPROX. O.D. SIZE BOX MASTER APPROX.
P/N P/N
(in.) QTY. PACK NET WT. (in.) QTY. PACK NET WT.
111R, RR or BH SERIES (continued) 1-1/8 x 1-1/8 x 1-3/8 5 50 .460 P805-W4082
5/8 x 5/8 x 1-1/8 10 100 .320 P805-W4067 1-1/8 x 1-1/8 x 1-5/8 5 50 .660 P805-W40101
5/8 x 5/8 x 7/8 25 250 .110 P805-W4047 1-1/8 x 1-1/8 x 1/2 10 100 .270 P805-W4052
5/8 x 5/8 x 3/4 50 500 .100 P805-W4029 1-1/8 x 1-1/8 x 5/8 10 100 .270 P805-W4051
5/8 x 5/8 x 1/2 50 500 .060 P805-W4007 1-1/8 x 1-1/8 x 7/8 10 100 .310 P805-W4049
5/8 x 5/8 x 3/8 50 500 .060 P805-W4008 1-1/8 x 5/8 x 1-1/8 10 100 .330 P805-W4061
5/8 x 5/8 x 1/4 50 500 .060 P805-W4014 1-1/8 x 5/8 x 5/8 10 100 .270 P805-W4063
5/8 x 1/2 x 5/8 50 500 .060 P805-W4009 1-1/8 x 5/8 x 7/8 10 100 .310 P805-W4062
5/8 x 1/2 x 1/2 50 500 .060 P805-W4010 1-1/8 x 7/8 x 1-1/8 10 100 .330 P805-W4055
5/8 x 1/2 x 13/8 50 500 .060 P805-W4011 1-1/8 x 7/8 x 3/4 10 100 .310 P805-W4057
5/8 x 3/8 x 5/8 50 500 .060 P805-W4012 1-1/8 x 7/8 x 5/8 10 100 .270 P805-W4058
5/8 x 3/8 x 3/8 50 500 .060 P805-W4013 1-1/8 x 7/8 x 7/8 10 100 .310 P805-W4056

O.D. SIZE BOX MASTER APPROX. O.D. SIZE BOX MASTER APPROX.
P/N P/N
(in.) QTY. PACK NET WT. (in.) QTY. PACK NET WT.
3/4 x 1/2 x 1/2 25 250 .100 P805-W4027 1-3/8 x 1-3/8 x 1-5/8 5 50 .690 P805-W40100
3/4 x 1/2 x 3/4 25 250 .100 P805-W4025 1-3/8 x 1-3/8 x 2-1/8 5 40 1.290 P805-W40122
3/4 x 1/2 x 3/8 P805-W4028 1-3/8 x 1-3/8 x 1-1/8 5 50 .450 P805-W4069
3/4 x 1/2 x 5/8 25 250 .100 P805-W4026 1-3/8 x 1-3/8 x 7/8 5 50 .370 P805-W4070
3/4 x 3/4 x 3/8 25 250 .100 P805-W4020 1-3/8 x 1-3/8 x 5/8 5 50 .320 P805-W4071
3/4 x 3/4 x 5/8 25 250 .100 P805-W4018 1-3/8 x 1-3/8 x 1/2 5 50 .320 P805-W4072
3/4 x 3/4 x 7/8 50 500 .150 P805-W4046 1-3/8 x 1-1/8 x 1-3/8 5 50 .460 P805-W4073
3/4 x 5/8 x 1/2 25 250 .100 P805-W4023 1-3/8 x 1-1/8 x 1-1/8 5 50 .450 P805-W4074
1-3/8 x 1-1/8 x 7/8 5 50 .370 P805-W4075
1-3/8 x 1-1/8 x 5/8 5 50 .330 P805-W4076
1-3/8 x 7/8 x 1-3/8 5 50 .470 P805-W4078
O.D. SIZE BOX MASTER APPROX.
P/N 1-3/8 x 7/8 x 1-1/8 5 50 .470 P805-W4079
(in.) QTY. PACK NET WT.
1-3/8 x 7/8 x 7/8 5 50 .370 P805-W4080
7/8 x 7/8 x 1-1/8 10 100 .330 P805-W4065
1-3/8 x 7/8 x 5/8 5 50 .320 P805-W4081
7/8 x 7/8 x 3/4 25 250 .150 P805-W4032
1-3/8 x 5/8 x 1-3/8 5 50 .450 P805-W4083
7/8 x 7/8 x 5/8 25 250 .140 P805-W4033
ELBOWS CONTINUED
7/8 x 7/8 x 1/2 25 250 .140 P805-W4034
7/8 x 7/8 x 3/8 25 250 .100 P805-W4035 *111R — Reducing on Outlet.
7/8 x 5/8 x 7/8 25 250 .150 P805-W4041 111RR — Reducing on Run.
7/8 x 5/8 x 5/8 25 250 .130 P805-W4043 111BH — Large Diameter Outlet
7/8 x 5/8 x 3/8 25 250 .140 P805-W4045
7/8 x 1/2 x 5/8 25 250 .140 P805-W40231
7/8 x 5/8 x 3/4 P805-W4042

NOTE: Order Totaline Fittings by Part Number and Model Series Number.

616
TOTALINE® COPPER REDUCING TEES
TOTALINE® COPPER REDUCING TEES

O.D. SIZE BOX MASTER APPROX. O.D. SIZE BOX MASTER APPROX.
P/N P/N
(in.) QTY. PACK NET WT. (in.) QTY. PACK NET WT.
111R, RR or BH SERIES (continued) 2-1/8 x 1-1/8 x 1-1/8 5 40 .900 P805-W40247
1-5/8 x 1-1/8 x 1-1/8 5 50 .610 P805-W4097 2-1/8 x 1-1/8 x 2-1/8 5 40 1.290 P805-W40245
1-5/8 x 1-1/8 x 1-3/8 5 50 .640 P805-W4096 2-1/8 x 1-3/8 x 1-1/8 5 40 1.000 P805-W40118
1-5/8 x 1-1/8 x 1-5/8 5 50 .690 P805-W4095 2-1/8 x 1-3/8 x 1-3/8 5 40 1.030 P805-W40117
1-5/8 x 1-1/8 x 5/8 5 50 .470 P805-W40237 2-1/8 x 1-3/8 x 1-5/8 5 40 1.090 P805-W40116
1-5/8 x 1-1/8 x 7/8 5 50 .560 P805-W4098 2-1/8 x 1-3/8 x 2-1/8 5 40 1.300 P805-W40115
1-5/8 x 1-3/8 x 1-1/8 5 50 .600 P805-W4092 2-1/8 x 1-3/8 x 7/8 5 40 .900 P805-W40119
1-5/8 x 1-3/8 x 1-3/8 5 50 .640 P805-W4091 2-1/8 x 1-5/8 x 1-1/8 5 40 .950 P805-W40112
1-5/8 x 1-3/8 x 1-5/8 5 50 .690 P805-W4090 2-1/8 x 1-5/8 x 1-3/8 5 40 1.030 P805-W40111
1-5/8 x 1-3/8 x 5/8 5 50 .470 P805-W4094 2-1/8 x 1-5/8 x 1-5/8 5 40 1.080 P805-W40110
1-5/8 x 1-3/8 x 7/8 5 50 .560 P805-W4093 2-1/8 x 1-5/8 x 2-1/8 5 40 1.300 P805-W40109
1-5/8 x 1-5/8 x 1-1/8 5 50 .610 P805-W4086 2-1/8 x 1-5/8 x 7/8 5 40 .900 P805-W40113
1-5/8 x 1-5/8 x 1-3/8 5 50 .640 P805-W4085 2-1/8 x 2-1/8 x 1-1/8 5 40 .990 P805-W40105
1-5/8 x 1-5/8 x 26.898 5 40 1.290 P805-W40121 2-1/8 x 2-1/8 x 1-3/8 5 40 1.030 P805-W40104
1-5/8 x 1-5/8 x 5/8 5 50 .470 P805-W4088 2-1/8 x 2-1/8 x 1-5/8 5 40 1.080 P805-W40103
1-5/8 x 1-5/8 x 7/8 5 50 .570 P805-W4087 2-1/8 x 2-1/8 x 2-5/8 1 10 1.900 P805-W40144
1-5/8 x 5/8 x 1-5/8 5 50 .670 P805-W40244 2-1/8 x 2-1/8 x 5/8 5 40 .860 P805-W40107
1-5/8 x 7/8 x 1-1/8 5 50 .600 P805-W40240 2-1/8 x 2-1/8 x 7/8 5 40 .920 P805-W40106
1-5/8 x 7/8 x 1-3/8 5 50 .640 P805-W40239 2-5/8 x 2-5/8 x 2-1/8 1 10 1.660 P805-W40124
1-5/8 x 7/8 x 1-5/8 5 50 .680 P805-W4099 2-5/8 x 2-5/8 x 1-5/8 1 10 1.410 P805-W40125
1-5/8 x 7/8 x 5/8 5 50 .470 P805-W40243 2-5/8 x 2-5/8 x 1-3/8 1 10 1.320 P805-W40126
1-5/8 x 7/8 x 7/8 5 50 .550 P805-W40238 2-5/8 x 2-5/8 x 1-1/8 1 10 1.340 P805-W40127
2-5/8 x 2-5/8 x 7/8 1 10 1.250 P805-W40128
2-5/8 x 2-5/8 x 5/8 1 10 1.060 P805-W40129
2-5/8 x 2-1/8 x 1-5/8 1 10 1.890 P805-W40130

*111R — Reducing on Outlet.


111RR — Reducing on Run.
111BH — Large Diameter Outlet.

NOTE: Order Totaline Fittings by Part Number and Model Series Number.

617
TOTALINE® COPPER REDUCING TEES
TOTALINE® COPPER REDUCING TEES

P786

Fitting to Fitting

O.D. SIZE BOX MASTER APPROX. O.D. SIZE BOX MASTER APPROX.
P/N P/N
(in.) QTY. PACK NET WT. (1N.) QTY. PACK NET WT.
2-5/8 x 2-1/8 x 2-1/8 1 10 1.630 P805-W40131 4-1/8 x 2-5/8 x 2-5/8 1 8 5.100 41S25S25S
2-5/8 x 2-1/8 x 1-5/8 1 10 1.410 P805-W40132 4-1/8 x 4-1/8 x 7/8 1 16 4.150 P805-W40192
2-5/8 x 1-5/8 x 2-1/8 1 10 1.630 P805-W40138 4-1/8 x 4-1/8 x 2-1/8 1 8 4.910 P805-W40196
2-5/8 x 1-5/8 x 1-5/8 1 10 1.400 P805-W40139 4-1/8 x 4-1/8 x 2-5/8 1 8 5.260 P805-W40197
2-5/8 x 1-3/8 x 2-5/8 1 10 1.890 P805-W40220 4-1/8 x 4-1/8 x 3-1/8 1 8 5.660 P805-W40198
2-5/8 x 1-1/8 x 2-5/8 1 10 1.860 P805-W40221 4-1/8 x 3-1/8 x 2-1/8 1 8 4.710 P805-W40204
2-5/8 x 7/8 x 2-5/8 1 10 1.870 P805-W40222 4-1/8 x 3-1/8 x 2-5/8 1 8 5.080 P805-W40205

O.D. SIZE BOX MASTER APPROX.


P/N
(in.) QTY. PACK NET WT.
3-1/8 x 2-5/8 x 7/8 1 10 2.370 31S25S14S
3-1/8 x 1-5/8 x 1-5/8 1 10 1.960 P31S15S15S
3-1/8 x 3-1/8 x 7/8 1 10 1.690 P805-W40146
3-1/8 x 3-1/8 x 1-1/8 1 10 1.900 P805-W40147
3-1/8 x 3-1/8 x 1-3/8 1 10 1.920 P805-W40148
3-1/8 x 3-1/8 x 1-5/8 1 10 2.050 P805-W40149
3-1/8 x 3-1/8 x 2-1/8 1 10 2.270 P805-W40150
3-1/8 x 3-1/8 x 2-5/8 1 10 2.420 P805-W40151
3-1/8 x 2-5/8 x 1-5/8 1 10 2.000 P805-W40156
3-1/8 x 2-5/8 x 2-5/8 1 10 2.400 P805-W40158
3-1/8 x 2-1/8 x 2-1/8 1 10 2.270 P805-W40164
3-1/8 x 2-1/8 x 2-5/8 1 10 2.220 P805-W40165

NOTE: Order Totaline Copper Fittings by Part Number and Model Series Number.

618
TOTALINE® COPPER PLUGS, TUBE CAPS & FITTINGS
TOTALINE® COPPER PLUGS, TUBE CAPS & FITTING REDUCERS
116 SERIES 117 SERIES 118 SERIES
END PLUG TUBE CAP FITTING REDUCER

P788
P789 P789
For Fitting For Tube End Fitting to Copper

O.D. SIZE BOX MASTER APPROX. O.D. SIZE BOX MASTER APPROX.
P/N P/N
(in.) QTY. PACK NET WT. (in.) QTY. PACK NET WT.
116 SERIES — END PLUG 7/8 x 1/2 50 500 .040 P805-W1327
7/8 x 3/8 50 500 .050 P805-W1328
1-1/8 x 7/8 25 250 .100 P805-W1337
O.D. SIZE BOX MASTER APPROX. P/N 1-1/8 x 3/4 25 250 .090 P805-W1338
(in.) QTY. PACK NET WT.
1-1/8 x 5/8 25 250 .100 P805-W1339
117 SERIES — TUBE CAP
1-1/8 x 1/2 25 250 .090 P805-W1340
1/4 50 1000 .003 P805-W7002
1-3/8 x 1-1/8 10 100 .150 P805-W1343
3/8 50 1000 .005 P805-W7004
1-3/8 x 7/8 10 100 .120 P805-W1345
1/2 50 1000 .009 P805-W7006
1-3/8 x 5/8 10 100 .150 P805-W1347
5/8 100 1000 .016 P805-W7007
1-5/8 x 1-3/8 10 100 .210 P805-W1350
3/4 25 500 .030 P805-W7008
1-5/8 x 1-1/8 10 100 .200 P805-W1351
7/8 50 500 .040 P805-W7009
1-5/8 x 7/8 10 100 .200 P805-W1353
1-1/8 50 500 .060 P805-W7011
1-5/8 x 5/8 10 100 .190 P805-W1355
1-3/8 25 250 .100 P805-W7012
2-1/8 x 1-5/8 10 100 .380 P805-W1358
1-5/8 20 200 .150 P805-W7013
2-1/8 x 1-3/8 10 100 .340 P805-W1359
2-1/8 10 100 .260 P805-W7014
2-1/8 x 1-1/8 10 100 .360 P805-W1360
2-5/8 5 50 .450 P805-W7015
2-1/8 x 7/8 10 100 .380 P805-W1362
3-1/8 5 50 .690 P805-W7016
2-1/8 x 5/8 10 100 .390 P805-W1364
3-5/8 1 10 .970 P805-W7017
2-5/8 x 2-1/8 5 50 .620 P805-W1367
4-1/8 1 10 1.340 P805-W7018
2-5/8 x 1-5/8 5 50 .640 P805-W1368
118 SERIES — FITTING REDUCER
2-5/8 x 1-3/8 5 50 .610 P805-W1369
1/4 x 1/8 50 1000 .004 P805-W1302
2-5/8 x 1-1/8 5 50 .600 P805-W1370
3/8 x 1/4 50 1000 .007 P805-W1306
3-1/8 x 2-5/8 2 20 .870 P805-W1376
1/2 x 3/8 50 1000 .014 P805-W1312
3-1/8 x 2-1/8 2 20 .950 P805-W1377
1/2 x 1/4 50 1000 .016 P805-W1314
3-1/8 x 1-5/8 2 20 .960 P805-W1378
5/8 x 1/2 50 1000 .027 P805-W1315
3-1/8 x 1-3/8 2 20 1.020 P805-W1379
5/8 x 3/8 50 1000 .023 P805-W1317
3-5/8 x 2-1/8 1 10 1.380 P805-W1383
3/4 x 5/8 25 500 .033 P805-W1320
4-1/8 x 3-5/8 2 32 1.850 P805-W1386
3/4 x 1/2 25 500 .035 P805-W1321
4-1/8 x 3-1/8 2 32 1.870 P805-W1387
3/4 x 3/8 25 500 .034 P805-W1322
4-1/8 x 2-5/8 2 32 1.970 P805-W1388
7/8 x 3/4 50 500 .060 P805-W1325
4-1/8 x 2-1/8 2 32 2.060 P805-W1389
7/8 x 5/8 50 500 .060 P805-W1326
5-1/8 x 4-1/8 1 6 4.070 P805-A2008

NOTE: Order Totaline Copper Fittings by Part Number and Model Series Number.

619
TOTALINE® COPPER FITTINGS
TOTALINE® COPPER BUSHINGS, FITTING REDUCERS P-TRAPS & BENDS
1193 SERIES 119 SERIES 123 SERIES 138 SERIES
FLUSH TYPE FLUSH TYPE SUCTION LINE RETURN
BUSHING FITTING REDUCER P-TRAP BEND

P790 P794
P791 Copper to
Copper Copper to
Fitting to Fitting to
Copper
Female N.P.T. Copper P792

O.D. SIZE BOX MASTER APPROX. O.D. SIZE BOX MASTER APPROX.
P/N P/N
(in.) QTY. PACK NET WT. (in.) QTY. PACK NET WT.
93 SERIES — FLUSH TYPE BUSHING 138 SERIES — RETURN BEND
5/8 x 1/8 50 1000 .036 P805-A7812 3/8 x 1-/2c 50 500 .029 P805-W6020
9 SERIES — FLUSH TYPE FITTING REDUCER 1/2 x 3c 25 250 .085 P805-W6041
3/8 x 1/4 50 1000 .008 P805-W1706 1/2 x 2c 25 250 .066 P805-W6036
1/2 x 3/8 50 1000 .012 P805-W1712 1/2 x 1-1/2c 25 250 .053 P805-W6032
1/2 x 1/4 50 1000 .021 P805-W1714 5/8 x 3c 25 250 .130 P805-W6060
5/8 x 1/2 50 1000 .022 P805-W1715 5/8 x 2-1/2c 25 250 .110 P805-W6058
5/8 x 3/8 50 1000 .037 P805-W1717 5/8 x 1-1/2c 25 250 .070 P805-W138 5/8X1 1/2C
3/4 x 5/8 25 500 .030 P805-W1720 3/4 x 2-1/4c 10 100 .140 P805-W138 3/4X2 1/4C
3/4 x 3/8 25 500 .077 P805-W1722 7/8 x 2-1/2c 10 100 .190 P805-W6092
7/8 x 3/4 50 500 .040 P805-W1725 1-1/8 x 3-1/4c 5 50 .350 P805-W60111
7/8 x 5/8 50 500 .080 P805-W1726 1-1/8 x 3c 5 50 .330 P805-W60110
-1/8 x 7/8 25 250 .120 P805-W1737 1-3/8 x 4c 5 40 .560 P805-W13SX4C
-1/8 x 3/4 25 250 .180 P805-W1738 1-5/8 x 4-3/8c 5 40 .800 P805-W15SX4-3/8C
-1/8 x 5/8 25 250 .220 P805-W1739 2-1/8 x 5-1/2c 4 32 1.750 P805-W60140
3/8 x 1-1/8 25 250 .160 P805-W1743 3-1/8 x 3-3/4 – – – P805-W60121
5/8x1-3/8 20 200 .210 P805-W1750 1-5/8 x4-1/2 – – – P805-W60131
1/8x1-5/8 5 50 .660 P805-W1758 5/8 x1-7/8 – – – P805-W6053
3 SERIES — SUCTION LINE P-TRAP 5/8 x1-3/8C – – – P805-W5/8X1-3/8C
5/8 5 50 .200 P805-W60999
3/4 10 60 .480 P805-W61008
7/8 10 60 .590 P805-W61000
1-1/8 10 10 1.090 P805-W61001
1-3/8 5 5 1.890 P805-W61002
1-5/8 5 5 3.710 P805-W61003
2-1/8 3 3 3.710 P805-W61009

OTE: Totaline Copper Fittings by Part Number and Model Series Number.

620
TOTALINE® COPPER FITTINGS & DATA
TOTALINE® COPPER TUBE STRAPS, EAR HANGERS & PERFORATED STRAPS
120 SERIES 120S SERIES 125 SERIES
TUBE STRAP TUBE STRAP PERFORATED STRAP

3/4”
Wide
P796

P795
Single Hole
Double Hole Heavy Weight P798

O.D. SIZE BOX MASTER APPROX. BOX MASTER APPROX.


P/N SIZE P/N
(in.) QTY. PACK NET WT. QTY. PACK NET WT.
120 SERIES - STRAP 125 SERIES - PERFORATED STRAP
1/4 100 2000 .005 P805-A1203 25 Ft. Roll 6 72 1.8 P805-A1211
3/8 100 2000 .007 P805-A1278
1/2 100 2000 .008 P805-A1366
5/8 100 1000 .009 P805-A2529
3/4 100 1000 .011 P805-A1467
7/8 100 1000 .012 P805-A2574
1-1/8 100 1000 .014 P805-A2614
1-3/8 50 500 .041 P805-A2650
1-5/8 50 500 .048 P805-A2675
2-1/8 100 800 .063 P805-A2708
120S SERIES - TUBE STRAP
1/4 100 2000 .007 P805-W120S 1/4
3/8 100 2000 .009 P805-W120S 3/8 NOTE: Order Totaline Copper Fittings by RCD Part
1/2 100 2000 .012 P805-W120S 1/2 Number and Model Series Number.
5/8 100 2000 .014 P805-W120S 5/8

COPPER AND BRONZE / SOLDER-JOINT PRESSURE FITTINGS


DIMENSIONS OF SOLDERED JOINT ENDS (Dimensions in Inches)

STAND- MALE END FEMALE END METAL INSIDE


ARD THICK- DIA. OF
OUTSIDE DIA. LENGTH INSIDE DIA. DEPTH
WATER NESS FITTING
TUBE
A K F G T O
SIZE MIN. MAX. MIN. MIN. MAX. MIN. MIN. MIN.
1/8 0.248 0.251 0.38 0.252 0.256 0.31 0.022 0.18
1/4 0.373 0.376 0.38 0.377 0.381 0.31 0.026 0.30
3/8 0.497 0.501 0.44 0.502 0.506 0.38 0.031 0.39
1/2 0.622 0.626 0.56 0.627 0.631 0.50 0.036 0.52
5/8 0.747 0.751 0.69 0.752 0.756 0.62 0.038 0.63
3/4 0.872 0.876 0.81 0.877 0.881 0.75 0.041 0.74
1 1.122 1.127 0.97 1.128 1.132 0.91 0.046 0.98
1-1/4 1.372 1.377 1.03 1.378 1.382 0.97 0.050 1.23
1-1/2 1.621 1.627 1.16 1.628 1.633 1.09 0.055 1.47
2 2.121 2.127 1.41 2.128 2.133 1.34 0.064 1.94
2-1/2 2.621 2.627 1.53 2.628 2.633 1.47 0.074 2.42
3 3.121 3.127 1.72 3.128 3.133 1.66 0.083 2.89
3-1/2 3.621 3.627 1.97 3.628 3.633 1.91 0.093 3.37
P391A 4 4.121 4.127 2.22 4.128 4.133 2.16 0.101 3.84
5 5.121 5.127 2.72 5.128 5.133 2.66 0.115 4.70
6 6.121 6.127 3.22 6.128 6.133 3.09 0.130 5.72
8 8.119 8.127 4.09 8.128 8.133 3.97 0.186 7.55
Extracted from American National Standard Wrought-Copper and Wrought-Bronze Solder-Joint Pressure Fittings (ANSI B16.22)
with the permission of the publisher. The American Society of Mechanical Engineers, 345 East 47th Street, New York, N.Y.

621
TOTALINE® COPPER FITTINGS DATA
COPPER SOLDER-JOINT DRAINAGE FITTINGS
DIMENSIONS OF SOLDERED JOINT ENDS (Dimensions in Inches)

STAND- MALE END FEMALE END METAL INSIDE


ARD THICK- DIA. OF
OUTSIDE DIA. LENGTH INSIDE DIA. DEPTH
WATER NESS FITTING
TUBE
A K F G T O
SIZE MIN. MAX. MIN. MIN. MAX. MIN. MIN. MIN.
1-1/4 1.372 1.377 0.56 1.378 1.382 0.50 0.040 1.29
1-1/2 1.621 1.627 0.62 1.628 1.633 0.56 0.042 1.53
2 2.121 2.127 0.69 2.128 2.133 0.62 0.042 2.01
3 3.121 3.127 0.81 3.128 3.133 0.75 0.045 2.98
4 4.121 4.127 1.06 4.128 4.133 1.00 0.058 3.93

Extracted from American National Standard Wrought-Copper and


Wrought-Bronze Solder-Joint Pressure Fittings (ANSI B16.22) with the
permission of the publisher. The American Society of Mechanical Engi-
neers, 345 East 47th Street, New York, N.Y.
P391A

LARGE DIAMETER, WELDED DESIGN COPPER FITTINGS


FITTING MATERIAL: Copper Allow #122, Phosphorus Deoxi- METHOD OF JOINING: Electric Weld.
dized-High Residual Phosphorus (DHP). Composition: 99%
DIMENSIONS & SPECIFICATIONS: Welded fittings are pro-
Copper; .015-040% Phosphorus.
duced in accordance with specifications shown in American
WELD MATERIAL: Silicon Bronze. Meets specification Ameri- National Standard (ANSI) B16.22 for wrought copper, and
can Welding Society (AWS) A5.7-69 and American Metals Soci- bronze solder-joint pressure fittings.
ety (AMS) 4616 B.
TESTING: Each fitting is individually tested with air under water.
WELD SPECIFICATIONS: Tensile Strength - Up to 58,000 PSI The bursting pressure of the weld exceeds that of straight,
Yield Strength - Up to 25,000 PSI seamless ASTM B88-70 Type “U” copper water tube, annealed,
Elongation in ’2’ - 53 to 55% of comparable diameter.
Hardness - 80 to 100 Brinell (500 kg. Load)
Temperature: Melt 18320F, Flow 19310F.

COPPER TUBE STANDARD DIMENSIONS AND WEIGHTS (Dimensions in Inches)


OUTSIDE
NOMI- INSIDE DIAMETER WALL THICKNESS POUNDS PER LINEAR FOOT†
DIA.
NAL
TYPES
TUBE TYPE TYPE TYPE TYPE TYPE TYPE TYPE TYPE TYPE TYPE TYPE TYPE
K-L-M
SIZE K L M DWV K L M DWV K L M DWV
DWV
1/4 .375 .305 .315 - - .035 .030 .025 - .145 .126 .106 -
3/8 .500 .402 .430 - - .049 .035 .025 - .269 .198 .145 -
1/2 .625 .527 .545 - - .049 .040 .028 - .344 .285 .204 -
5/8 .750 .652 .666 - - .049 .042 .030 - .418 .362 .263 -
3/4 .875 .745 .785 - - .065 .045 .032 - .641 .455 .328 -
1 1.125 .995 1.025 - - .065 .050 .035 - .839 .655 .465 -
1-1/4 1.375 1.245 1.265 1.291 1.295 .065 .055 .042 .040 1.04 .884 .682 .650
1-1/2 1.625 1.481 1.505 1.527 1.541 .072 .060 .049 .042 1.36 1.14 .940 .809
2 2.125 1.959 1.985 2.009 2.041 .083 .070 .058 .042 2.06 1.75 1.46 1.07
2-1/2 2.625 2.435 2.465 2.495 - .095 .080 .065 - 2.93 2.48 2.03 -
3 3.125 2.907 2.945 2.981 3.035 .109 .090 .072 .045 4.00 3.33 2.68 1.69
3-1/2 3.625 3.385 3.425 3.459 - .120 .100 .083 - 5.12 4.29 3.58 -
4 4.125 3.857 3.905 3.935 4.009 .134 .110 .095 .058 6.51 5.38 4.66 2.87
5 5.125 4.805 4.875 4.907 4.981 .160 .125 .109 .072 9.67 7.61 6.66 4.43
6 6.125 5.741 5.845 5.881 5.959 .192 .140 .122 .083 13.9 10.2 8.92 6.10
8 8.125 7.583 7.725 7.785 - .271 .200 .170 - 25.9 19.3 16.5 -

†Slight variations from these weights must be expected in practice.

622
TOTALINE® COPPER FITTINGS DATA
COPPER TUBE, CALCULATED BURSTING PRESSURE*
OUTSIDE INSIDE DIAMETER WALL THICKNESS BURSTING PRESSUR
NOMINAL DIA. (in.) (in.) (in.) (lbs per sq in.)
TUBE SIZE TYPE K TYPE L
(in.) TYPE K-L TYPE K TYPE L TYPE K TYPE L HARD SOFT HARD SOFT
(DRAWN) (ANNEALED) (DRAWN) (ANNEALED)
1/4 .375 .305 .315 .035 .030 6,700 5,600 5,800 4,800
3/8 .500 .402 .430 .049 .035 7,100 5,900 5,000 4,200
1/2 .625 .527 .545 .049 .040 5,600 4,700 4,600 3,800
5/8 .750 .652 .666 .049 .042 4,700 3,900 4,000 3,400
3/4 .875 .745 .785 .065 .045 5,300 4,500 3,700 3,100
1 1.125 .995 1.025 .065 .050 4,200 3,500 3,200 2,700
1-1/4 1.375 1.245 1.265 .065 .055 3,400 2,800 2,900 2,400
1-1/2 1.625 1.481 1.505 .072 .060 3,200 2,700 2,700 2,200
2 2.125 1.959 1.985 .083 .070 2,800 2,300 2,400 2,000
2-1/2 2.625 2.435 2.465 .095 .080 2,600 2,200 2,200 1,800
3 3.125 2.907 2.945 .109 .090 2,500 2,100 2,100 1,700
3-1/2 3.625 3.385 3.425 .120 .100 2,400 2,000 2,000 1,700
4 4.125 3.857 3.905 .134 .110 2,300 1,900 1,900 1,600
5 5.125 4.805 4.875 .160 .125 2,200 1,900 1,800 1,500
6 6.125 5.741 5.845 .192 .140 2,300 1,900 1,600 1,400
8 8.125 7.583 7.725 .271 .200 2,400 2,000 1,800 1,500
*Bursting Pressures are calculated from the following formula for thin, hollow cylinders under tension:
2tS Where P = Bursting Pressure, lb. per sq. in.
P = --------
D t = Wall Thickness, inches
D = Outside Tube Diameter, inches
S = Tensile Strength (36,000 lb. per sq. in. for hard tubes and 30,000 for soft tubes)

With factor of safety of 5, maximum working pressure allowable by common usage up to 150° F can be taken at 1/5 the above bursting
pressures.

SOLDERING AND BRAZING COPPER TUBE


Soldering and Brazing with capillary solder joint fittings is the most Cleaning - Cleaning is quickly and easily done. The removal of oxides
common system for joining copper tube. The American Welding Soci- and surface soil is crucial if filler metal is to flow properly. Oxides, surface
ety defines soldering as a joining process which takes place below soil and oil can interfere with the strength of the joint and this may result in
840° and brazing as a similar process which occurs above 840°. the joint’s failure. Mechanical cleaning is a simple operation. The end of
the tube should be cleaned using sand cloth or nylon abrasive pads for a
The basic theory and technique of soldering and brazing are the same
for all diameters ... the variables are: the amount of time, heat and distance only slightly more than the depth of the fitting socket. The socket
filler metal required to complete a designated joint. A good joint is the of the fitting should also be cleaned using sand cloth, abrasive pads, or
properly sized fitting brushes. The same precautions, as when reaming
product of a well trained craftsman who knows and respects the mate-
the tube, should be observed.
rials and methods he uses.
Copper is a soft metal; if too much material is removed, a loose fit will
BASIC STEPS IN JOINING PROCESS result and interfere with satisfactory capillary action in making the joint.
Measuring - Measuring the length of the tube must be accurate. If the The capillary space between tube and fitting is approximately .004 in. Sol-
tube is too short it will not reach all the way into the socket of the fitting der or brazing filler metal can fill this gap by capillary action. This spacing
and a proper joint cannot be made. is critical for the filler metal to flow into the gap and form a strong joint.
Chemical cleaning may be utilized, providing the tube and fittings are thor-
Cutting - Cutting tube can be accomplished in a number of different
oughly rinsed according to the manufacturer’s recommendations fur-
ways to produce a satisfactory, square-end cut. The tube can be cut
nished with the cleaner. This will help neutralize any acidic conditions that
with a disc type tube cutter, a hacksaw, abrasive wheels, or stationary
may exist. The surfaces, once cleaned, should not be touched with bare
and portable bandsaws. Care must be taken that the tube is not
hands or oily gloves. Skin oils, lubricating oils and grease impair solder
deformed while being cut. Regardless of the cutting method used, the
flow and wetting.
cut must be square with the run of the tube so that it will seat properly
in the fitting socket. TEMPERATURE RANGES
Reaming - Most methods of cutting leave a small burr on the end of Up to this point, the joining process is the same for both soldering and
the tube. Unless these rough edges are removed, erosion-corrosion brazing. The choice for soldering or brazing will depend upon operating
may occur due to local turbulence and increased velocities in the tube. conditions. Solder joints are generally used where the system tempera-
Tools used to ream tube ends include the reaming blade on the tube tures do not exceed 250° F and brazed joints can be used where greater
cutter half-round or round files, a pocket knife, or a suitable deburring strengths are required, or where system temperatures are as high as
tool. With annealed tube, care must be taken not to get the tube end 350° F. In actual practice, most soldering is done at temperatures about
out-of-round by applying too much pressure. Both the inside and the 350° F to 550° F, while brazing is done at temperatures ranging from
outside of the tube may require removal of the burr. A properly reamed 1100° F to 1550° F.
piece of tube will provide a smooth surface for better flow. Because of the differences in the soldering and brazing processes, each
will be discussed separately.

623
TOTALINE® COPPER FITTINGS DATA
SOLDERING AND BRAZING COPPER TUBE (continued)
SOLDERING: provide the craftsman with an indication of temperature. Application of
Applying Flux - A non-aggressive soldering flux is recommended. Stir the flux is the same as when soldering. If the outside of the fitting and
the flux before use. A good flux will dissolve and remove traces of resid- the heat affected area of the tube are covered with flux, it will prevent
ual oxides from the surfaces to be joined, protect the surfaces from oxidation and greatly improve the appearance of the joint.
re-oxidation during heating and promote the wetting of the surfaces by Brazing Filler Metals - There are two general types of brazing filler
the solder A thin, even coating of flux should be applied with a brush to metals used for joining copper tube: BCuP (Brazing - Copper - Phos-
both tube and fitting. Avoid the use of fingers to apply flux. Chemicals in phorus) and BAg (Brazing - Silver). These brazing filler metals are clas-
the flux can be harmful if carried to the eyes of open cuts. sified according to their components.
Types of Solder - There are a variety of solders available that will pro- BCuP filler metals are preferred for joining copper tube and fittings. The
duce sound, leak-tight joints. Solders that are used for piping applica- phosphorus in these filler metals acts as a fluxing agent and the lower
tions contain tin and varying amounts of either antimony, copper, lead percentage of silver makes them relatively low cost filler metals. When
or silver. Choice of solder will depend upon application and local codes. using copper tube, wrot copper fittings and BCuP brazing filler metal,
For potable water systems, solders which do not contain lead are the fluxing is an option due to the self-fluxing action of the phosphorus
best choice. present in all components of the brazed joint.
Assembly - After both surfaces are properly fluxed, they should be The choice of brazing filler metals depends upon four main factors:
assembled by placing the fitting on the tube, making sure the tube seats 1) dimensional tolerance of the joint
against the base of the fitting socket. A slight twisting motion is sug- 2) type and material of fitting (cast or wrot)
gested to ensure even coverage by the flux. Remove the excess flux
3) desired appearance
with a rag. Because of the heat that is required during soldering and
brazing, only cotton rags should be used. Complete all prepared joints 4) cost.
within a single work day. Care must be taken to assure that the tube Heating - Oxy/fuel torches are generally used when brazing because of
and fittings are properly supported with a reasonable, uniform capillary the higher temperatures required. Due to recent innovations in air/fuel
space around the entire circumference of the joint. Uniformity of capil- torch tip design, they can now be used on a wider variety of sizes for
lary space will ensure good filler metal penetration if the guidelines of soldering and brazing.
successful joint making are followed. Excessive joint clearance can When working with temperatures this high, safety precautions must be
cause the filler metal to crack under stress or vibration. followed and care taken to protect both the operator and the materials
Heating - Because of the open flame and high temperatures required being used.
for soldering and the flammability of the gases used, safety precautions The heating operation is the same as for soldering. First preheat the
must be observed. The heat is generally applied by use of an air/fuel tube and then the tube and fitting. When the brazing filler metal starts to
torch. These torches can use acetylene or a variety of LP gases. Elec- melt, apply the heat at the base of the fitting socket to help draw the
tric resistance pliers can also be used. brazing filler metal by capillary action.
Heating should begin with the flame perpendicular to the tube. This pre- Applying Brazing Filler Metal - Remember to allow the heat of the
heat will conduct the initial heat into the socket for even distribution of joint to melt the filler metal. Do not melt the filler metal with the torch.
heat inside and out. Preheating depends upon the size of the joint - The melted filler metal will be drawn into the joint by capillary action. It is
experience will indicate the proper amount of time. The flame should very important that the flame be in continuous motion and should not be
now be moved onto the fitting. Move the flame from the fitting socket allowed to remain on any one point long enough to burn through the
onto the tube a distance equal to the fitting socket. Touch the solder to tube or fitting. When the joint is complete, a continuous fillet should be
the joint. If the solder does not melt, remove it and continue the heating visible completely around the joint. If the filler metal fails to flow, or has
process. Be careful not to overheat or direct the flame into the fitting the tendency to ball-up, it indicated oxidation on the metal surfaces or
cup. This action can cause the flux to burn and destroy its effective- insufficient heat on the parts to be joined. If the filler metal refuses to
ness. When the melting temperature has been reached, heat may be enter the joint and tends to flow over the outside of either part of the
applied to the base of the cup to aid capillary action in drawing the sol- joint, it indicates that this part is overheated or that the other part is
der into the cup. underheated.
Applying Solder - When the tube is in a horizontal position, start Cooling and Cleaning - When the joint is complete, allow it to cool nat-
applying the solder slightly off-center of the bottom of the joint. Proceed urally. Flux residues can be removed by washing with hot water and
across the bottom of the fitting and up to the top-center position. Return brushing with a stainless steel wire brush.
to the point of beginning, overlap the starting point and then proceed up
SUMMARY
the incompleted side to the top. Again, overlapping the solder. Molten
solder will be drawn into the joint by capillary action regardless if the If the parts to be joined are properly prepared, properly heated and the
solder is being fed upward, downward or horizontally. correct filler metal is used the finished joint should be sound. Soldered
or brazed copper piping systems, when installed properly, will provide
Cooling & Cleaning - After the joint has been completed, natural cool-
years of safe and reliable service. Proper training of the correct installa-
ing is best. Shock cooling may cause unnecessary stresses on the joint
tion techniques, such as those just covered, will give the craftsman the
and may result in eventual failure. Clean off any remaining flux with a
ability to achieve consistently reliable soldered and brazed joints in all
wet rag.
diameters.
BRAZING:
Prepared with technical assistance from the Copper Development
Applying Flux - The fluxes used for brazing copper joints are different Association.
in composition from soldering fluxes. They cannot, and should not, be
used interchangeably.
Brazing fluxes are water based. Similar to soldering fluxes, brazing
fluxes dissolve and remove residual oxides from the metal surfaces,
they protect the metal surfaces from re- oxidation during heating and
they promote the wetting of the surfaces to be joined by the brazing
filler metal. Fluxes also

624

Das könnte Ihnen auch gefallen