Beruflich Dokumente
Kultur Dokumente
10 Gigabit/s Ethernet
SFP+ Dual Port
User Guide
E10102
First Edition
February 2015
ii
Contents
Contents....................................................................................................................... iii
About this guide.......................................................................................................... iv
How this guide is organized.............................................................................iv
Where to find more information........................................................................iv
Conventions used in this guide........................................................................ v
Typography...................................................................................................... v
PEI-10G/82599-2S Specifications Summary............................................................. vi
iii
About this guide
This user guide contains the information you need when installing and configuring the server
management board.
iv
Conventions used in this guide
To make sure that you perform certain tasks properly, take note of the following symbols
used throughout this manual.
Typography
Bold text Indicates a menu or an item to select.
Italics Used to emphasize a word or a phrase.
<Key> Keys enclosed in the less-than and greater-than sign means
that you must press the enclosed key.
Example: <Enter> means that you must press the Enter or
Return key.
<Key1>+<Key2>+<Key3> If you must press two or more keys simultaneously, the key
names are linked with a plus sign (+).
Example: <Ctrl>+<Alt>+<Del>
Command
Means that you must type the command exactly as shown,
then supply the required item or value enclosed in
brackets.
Example: At the DOS prompt, type the command line:
format a:
v
PEI-10G/82599-2S Specifications Summary
PEI-10G/82599-2S
Speed & Ports 10 Gigabit/s Ethernet SFP+ ; Dual Port
Controller Intel® 82599 10 Gigabit Ethernet Controller
LC Fiber Optic
Connector & Module Type Supports SFP+ SR Optical Module, SFP+ LR Optical
Module, Direct Attached Copper*
Host Interface PCI-E Gen2 x8
Form Factor 4.72 in. x 1.77 in. (Lower Than Standard Low-profile)
SMF up to 10km (LR)
vi
1
Product introduction
* The bundled small bracket for node is a proprietray bracket that supports ASUS
Z10PH-D16 series, ESC4000 G3 series, and RS720Q-E8 series models, etc. The
supported list of models are subject to change without prior notice.
Back view
LED indications
Speed/Link
Status Description
SFP2SLED1 / Green 10 Gbps link
SFP2SLED2 Amber 1 Gbps link
Blinking Data Activity
The proprietray bracket supports ASUS Z10PH-D16 series, ESC4000 G3 series, and
RS720Q-E8 series models, etc. The supported list of models are subject to change without
prior notice.
Screw
Default card bracket
Screw
Screw
3. From the Setup Menu screen, use the Up/Down arrow key to select an item and press
<Space> to change the value.
3. From the iSCSI Port Selection screen, use the Up/Down arrow key to select an
Ethernet device to configure and press <Enter>.
Intel(R) iSCSI Remote Boot v3.0.34
• Press <P> to set the selected item as the primary boot priority, press <S> to set the
selected item as the secondary boot priority, or press <D> to disable the selected item.
• Press <B> to blink the LED of the selected item.
4. From the iSCSI Port Configuration screen, use the Up/Down arrow key to select an
item and press <Enter>.
Intel(R) iSCSI Remote Boot v3.0.34
Use the Up/Down arrow key to select an item and press <spacebar> to change between
Enabled [*] or Disabled [ ].
[OK] [Cancel]
Use the Up/Down arrow key to select an item and press <spacebar> to change between
Enabled [*] or Disabled [ ].
[ ] Use CHAP
When Enabled [*], the iSCSI boot host software uses CHAP authentication when connecting
to the iSCSI target. Key in the necessary parameters.
When Disabled [ ], the iSCSI boot host software does not attempt to boot from the iSCSI
target after successfully connecting to it. The control will then return to the system BIOS so
that the next boot device may be used.
The utility must run under pure DOS environment. It cannot run in a DOS box on Windows
system. You should boot from a DOS floppy without any device drivers
3. Within the DOS enviroment, enter the directory with the bootutil file.
4. Check the MAC address of the corresponding LAN card:
bootutil -E
C:\>bootutil -E
NIC= 1 MACAddress=00E018122208
NIC= 2 MACAddress=00E018122209
NIC= 3 MACAddress=00E01803016C
NIC= 4 MACAddress=00E01803016D
NIC= 5 MACAddress=00E01803016E
NIC= 6 MACAddress=00E01803016F
C:\>
or
• If Windows® automatically detects the LAN controllers and displays a New Hardware
Found window, click Cancel to close this window.
• If Autorun is NOT enabled in your computer, browse the contents of the Support CD to
locate the file Setup.exe. Double-click Setup.exe to run the CD.
4. Click Next when the Intel(R) Network Connections Install Wizard window appears.
7. If the Windows Security window appears during the driver installation, click Install
this driver software anyway to continue.
cd src
For Red Hat Enterprise Linux 6.5 (Red Hat Enterprise Linux 5.11):
make install
For Red Hat Enterprise Linux 6.5 (Red Hat Enterprise Linux 5.11):
5. Install complete:
For Red Hat Enterprise Linux 6.5 (Red Hat Enterprise Linux 5.11):
Technical Support
Telephone +86-21-38429911
Fax +86-21-58668722 ext: 9101
Online Support http://support.asus.com/techserv/techserv.aspx
Technical Support
Telephone +886-2-2894-3447 (0800-093-456)
Online Support http://support.asus.com/techserv/techserv.aspx
Technical Support
Telephone 400-620-6655
Online Support http://support.asus.com/techserv/techserv.aspx
EC Declaration of Conformity
DECLARATION OF CONFORMITY We, the undersigned,
Manufacturer: ASUSTeK COMPUTER INC.
Per FCC Part 2 Section 2. 1077(a)
Address: 4F, No. 150, LI-TE Rd., PEITOU, TAIPEI 112, TAIWAN
Authorized representative in Europe: ASUS COMPUTER GmbH
Address, City: HARKORT STR. 21-23, 40880 RATINGEN
Country: GERMANY
declare the following apparatus:
Product name : 10G LAN Card
Responsible Party Name: Asus Computer International Model name : PEI-10G/82599-2S
conform with the essential requirements of the following directives:
Address: 800 Corporate Way, Fremont, CA 94539. 2004/108/EC-EMC Directive
EN 55022:2010+AC:2011 EN 55024:2010
EN 61000-3-2:2006+A2:2009 EN 61000-3-3:2013
Phone/Fax No: (510)739-3777/(510)608-4555 EN 55013:2001+A1:2003+A2:2006 EN 55020:2007+A11:2011
1999/5/EC-R&TTE Directive
hereby declares that the product EN 300 328 V1.8.1(2012-06) EN 301 489-1 V1.9.2(2011-09)
EN 300 440-1 V1.6.1(2010-08) EN 301 489-3 V1.4.1(2002-08)
EN 300 440-2 V1.4.1(2010-08) EN 301 489-4 V1.4.1(2009-05)
Product Name : 10G LAN Card EN 301 511 V9.0.2(2003-03) EN 301 489-7 V1.3.1(2005-11)
EN 301 908-1 V5.2.1(2011-05) EN 301 489-9 V1.4.1(2007-11)
EN 301 908-2 V5.2.1(2011-07) EN 301 489-17 V2.2.1(2012-09)
EN 301 893 V1.7.1(2012-06) EN 301 489-24 V1.5.1(2010-09)
Model Number : PEI-10G/82599-2S EN 302 544-2 V1.1.1(2009-01) EN 302 326-2 V1.2.2(2007-06)
EN 302 623 V1.1.1(2009-01) EN 302 326-3 V1.3.1(2007-09)
EN 50360:2001 EN 301 357-2 V1.4.1(2008-11)
Conforms to the following specifications: EN 62479:2010 EN 302 291-1 V1.1.1(2005-07)
EN 50385:2002 EN 302 291-2 V1.1.1(2005-07)
EN 62311:2008
FCC Part 15, Subpart B, Unintentional Radiators 2006/95/EC-LVD Directive
EN 60950-1 / A12:2011 EN 60065:2002 / A12:2011
Supplementary Information:
2009/125/EC-ErP Directive
Regulation (EC) No. 1275/2008 Regulation (EC) No. 278/2009
This device complies with part 15 of the FCC Rules. Operation is subject to the
Regulation (EC) No. 642/2009 Regulation (EC) No. 617/2013
following two conditions: (1) This device may not cause harmful interference,
2011/65/EU-RoHS Directive Ver. 140331
and (2) this device must accept any interference received, including interference
that may cause undesired operation. CE marking
Position : CEO
Name : Jerry Shen
Signature :
Declaration Date: 13/02/2015
Date : Feb. 13, 2015 Year to begin affixing CE marking: 2015 Signature : __________
Ver. 140331