Beruflich Dokumente
Kultur Dokumente
EasyNote BU Series
Disassembly Guide
Table of Contents
Overview ..................................................................................................................3
Technician Notes......................................................................................................3
Disassembly Instructions..........................................................................................3
Reassembly Instructions ..........................................................................................3
Required Tools .........................................................................................................3
Battery ......................................................................................................................4
Memory ....................................................................................................................4
Hard Disk..................................................................................................................5
Optical Drive.............................................................................................................7
CPU and CPU fan ....................................................................................................9
Keyboard ................................................................................................................10
Wireless LAN Adapter ............................................................................................11
Top Cover...............................................................................................................12
Bluetooth Module....................................................................................................15
Launch Board .........................................................................................................15
Fingerprint Scanner ................................................................................................15
Touchpad ...............................................................................................................17
LCD Assembly........................................................................................................17
Main Board .............................................................................................................18
I/O Board ................................................................................................................18
LCD Panel ..............................................................................................................19
Inverter Board.........................................................................................................21
Speakers, Wireless LAN Antennas, Webcam and Microphone..............................21
Reassembly Notes .................................................................................................22
Notice .....................................................................................................................22
Packard Bell reserves the right to make changes to the EasyNote BU series without
notice.
Technician Notes
Only technicians authorized by Packard Bell B.V. should attempt to repair this
equipment. All troubleshooting and repair procedures are detailed to allow only
subassembly/module level repair. Because of the complexity of the individual boards
and subassemblies, no one should attempt to make repairs at the component level or to
make modifications to any printed wiring board. Improper repairs can create a safety
hazard. Any indication of component replacement or printed wiring board modifications
may void any warranty or exchange allowances.
Disassembly Instructions
When disassembling the unit, follow these general rules:
Reassembly Instructions
Reassembly is the reverse of the disassembly process. Use care to ensure that all
cables and screws are returned to their proper positions. Check that no tools or any
loose parts have been left inside the product. Check that everything is properly installed
and tightened.
Required Tools
All disassembly procedures can be performed using the following tools:
Memory
1. Remove the battery as described under ‘
Battery’
.
2. Remove the five screws and take away the cover.
Hard Disk
1. Remove the battery as described under ‘
Battery’.
2. Remove the five screws and take away the cover (see Fig. 2).
3. Remove the two screws securing the hard disk.
6. Remove the the four to release the metal bracket from the hard disk.
Optical Drive
1. Remove the battery as described under ‘
Battery’ .
2. Remove the five screws and take away the cover (see Fig. 2).
3. Remove the two screws securing the optical drive.
7. Push the two clips to release the bezel, and then pull the bezel off.
Keyboard
1. Remove the battery as described under ‘ Battery’
.
2. Push back the four clips and gently lift the keyboard.
4. Lift the card and disconnect the antennas. Note for each antenna
(black/grey) to which connector (main/aux) it was connected.
5. Lift out the card.
Top Cover
1. Remove the keyboard, hard disk, optical and CPU fan as described in
the sections above.
2. Disconnect two flat cables and the round cable with the connector.
a. Flat cable (launch board): lift the clip and slide out the cable.
Launch Board
This contains the power button, WiFi button and ECO button.
1. Remove the top cover as described under ‘ Top cover’
.
2. The launch board is mounted in the top cover.
Fingerprint Scanner
1. Remove the top cover as described under ‘ Top Cover’ .
2. The fingerprint scanner is located in de touchpad on the top cover.
Touchpad
The touchpad assembly is shipped as part of the top cover and does not need
further disassembly.
LCD Assembly
1. Remove the top cover as described under ‘ Top Cover’
.
2. Disconnect the Wireless LAN Adapter antennas and loosen the
antennas from the tape holding it in place.
3. Disconnect and remove all remaining flat cables from the main board
(all these cables can be slid out).
4. Remove the four screws in the hinges (two at each side).
Main Board
1. Remove the CPU, memory and top cover as described under ‘
Top
Cover’
.
2. Remove the nine screws from the main board.
3. Pull the connector between the I/O Board and the main board loose.
4. Lift the main board and slide it to the left to release the VGA port.
5. Lift out the main board.
I/O Board
1. Remove the main board as described under ‘
Main Board’
.
Note: During re-assembly, take care to align the main board and I/O board properly before
pushing them back together (to avoid bending the pins of the connector).
LCD Panel
1. Remove the LCD Assembly as described under ‘ LCD Assembly’ .
2. On the LCD assembly, remove five rubber stoppers.
3. Remover the five screws that were covered by the rubber stoppers.
4. Remove the LCD bezel clicked in place. Note that the bezel may be
glued on the top side (at the webcam and microphone). A bit of force
may be needed to pull the bezel loose.
5. Disconnect the power cable from the inverter board.
6. Remove the four screws from the hinges (two at each side).
7. Lift out the LCD panel.
EasyNote BU Disassembly Manual 20
8. Remove the metal brackets from the panel (two screws at each side).
9. Disconnect the LCD cable from the rear side of the panel.
Inverter Board
1. Remove the LCD Assembly as described under ‘ LCD Assembly’ .
2. On the LCD Assembly, remove five rubber stoppers (see Fig. 27).
3. Remove the five screws that were covered by the rubber stoppers.
4. Remove the LCD bezel clicked in place. Note that the bezel may be
glued on the top side (at the webcam and microphone). A bit of force
may be needed to pull the bezel loose.
5. Disconnect both cables from the inverter board.
6. Pull out the inverter board; it is glued in place so some force may be
needed to pull it out.
Note: After extracting the inverter board, ensure that the aluminium protective foil in the LCD
housing is still good. Flatten the foil before putting the inverter board back!
Notice
The information in this guide is subject to change without notice.