Beruflich Dokumente
Kultur Dokumente
Yadav Measurements)
8 Cyclic Volume test 5.8 Not defined Not a value adding test. May not be added in IS.
30 Chemical resistance of the protective coating 6.4.2.4 4.2.2 (Part1); however no test
Tests like salt spay needs to be defined in IS also
defined
31 Resistance to humidity/ humidity 6.4.2.6
Resistance to Internal corrosion 6.4.3
32 Adhesion of the protective coating 6.4.3.1
33 Impact Resistance of the Protective Coating 6.4.3.2
defined in Annex B (part 1) as dry, requirement of error during the test shall be
36 Resistance to storage temperature range 6.5 cold ; however acceptance criteria removed. Acceptance criteria for before and
not clearly defined after the test shall be added.
43 Diaphragm gas meters provided with a built-in 6.6.7 6.5 (part 2) Needs to be detailed out as per EN1359 / OIML
gas temperature conversion device
44 Additional functionalities 6.6.8 Not defined Shall be added in IS
Mechanical Performance 7
45 Durability 8.2.3 (part2) but not in line with
7.1.2 EN1359
Needs to be reviewed in line with EN1359 / OIML
IS 14439-1 15 Yadav Measurements 10.2 (d) (i) Editorial …..test conditions specified in 12.5.3” ……test conditions specified in 12.1.5.3 (e)”
For all the tests in this Annexure , the The suitable acceptance criteria may be
IS 14439-1 16 Yadav Measurements Annex B - Technical
acceptance criteria has not been defined included.
Electrical The note refer to IEC 801-4, which has been The current equivalent Indian standard is IS
IS 14439-1 17 Yadav Measurements - Technical
Bursts B-8 withdrawn long back. 14700 (Part 4/Sec 4):2018
Replace IEC 801-4 with 14700 (Part 4/Sec
B-8,B-9 & Refer old IEC standards. Need to replace 4):2018 , IEC 801-2 with IS14700 part 4 sec
IS 14439-1 18 Secure Meters Ltd. Editorial
B10 with active equivalent IS standards. 2: 2018 and IEC 801-3 IS14700 part 4 sec 3:
2018.
The note refer to IEC 801-2, which has been The current equivalent Indian standard is IS
IS 14439-1 19 Yadav Measurements ESD , B-9 - Technical
withdrawn long back. 14700 part 4 sec 2: 2018
Electromagn
etic The note refer to IEC 801-3, which has been The current equivalent Indian standard is IS
IS 14439-1 20 Yadav Measurements Technical
susceptibilit withdrawn long back. 14700 part 4 sec 3 : 2008
y B-10
Line 1
“to prevent flow
Mechanism to prevent flow in unauthorized
IS 14439-2 1 Natural Gas Society 4.2 of gas in an Technical
direction to be defined
unauthorized
direction”
Page 3 of 34
Type of Comments
Sl Clause / Paragraph /
IS Standard Names of the Organization (General / Technical / Comments Proposed change
No sub-clause Fig. / Table
Editorial)
In 6.1 ‘reference condition reference is not Add correct reference for reference
IS 14439-2 3 Secure Meters Ltd. 6.1 Editorial
clear. condition or add reference condition here.
Page 4 of 34
Table ZA.1 — Identification form on the compliance of EN 1359 with th
EU Directive 2004/22/EC (MID) on the approximation of the laws of member
Essential Requirements
ANNEXURE 1
1
1.1
1.3.3
1.3.4
1.4.1
1.4.2
2
3
4
5
6
7
7.1
7.2
7.3
7.4
7.5
7.6
8
8.1
8.2
8.3
8.4
8.5
9
9.1
9.2
9.3
9.4
9.5
9.6
9.7
9.8
10
10.1
10.2
10.3
10.4
10.5
11
11.1
11.2
12
Table ZA.1 — Identification form on the compliance of EN 1359 with the essential requirem
approximation of the laws of member states on Measurin
Essential Requirements
Part I
1
1.1
1.2
1.3
1.4
1.5
2
2.1
2.2
3
3.1
3.2
4
4.1
4.2
5
5.1
5.2
5.3
5.4
5.5
5.6
6
PART II
7
8
9
PART III
10
(a)
(b)
(C)
Table ZA.1 — Identification form on the compliance of EN 1359 with the essential requirements of
U Directive 2004/22/EC (MID) on the approximation of the laws of member states on Measuring Instruments
Subject
dentification form on the compliance of EN 1359 with the essential requirements of EU Directive 2004/22/EC
approximation of the laws of member states on Measuring Instruments
Subject
Annex M1002
Specific requirements gas meters
Rated operating conditions
Flow-rate
T>40 gas
Gas family/MOP
T>50 climatic
Limits of dc supply
Maximum permissible errors
MPE
MPE TC
Permissible effects of disturbances
EMC
Flow disturbances
Durability
Durability — Class 1,5 meters
Durability — Class 1,0 meters
Suitability
Mains power
Battery power
8 000 hours
Any position
Test element
Flow direction marked
Units
Specific requirements — Volume conversion devices
Base conditions for converted quantities
Maximum permissible error
Suitability
Putting into use and conformity assessment
Putting into use
Conformity assessment
he essential requirements of
r states on Measuring Instruments
Conformity
(Clause)
5.2, 7.2
NA
NA
6.6, 7.3
7.2.1
5.7
6.1
NA
NA
7.2.1
8.1
NA
6.1 (A.4)
6.1 (A.4)
7.2
7.2.1
8.3
7.2
7.2 , 8.3
NA
NA
7.2
NA
NA
Whole Stanadard
1, 4.1
4.3
1, 6.2.2, 7.1.2, 7.3, 8.1(f)
4.3
NA
1
NA
NA
NA
7.2
6.1 (A.4)
7.2
8.2
7.2
NA
NA
NA
NA
NA
NA
NA
NA
Date: 17/01/18 Diaphragm Gas Meters
Parameter MGL GAIL Gas (Mecon) Avantika Green Gas (JP Kenny)
Sizes G4, G6, G16, G25, G40 G4, G6, G16, G25, G40 G4, G6, G16, G25, G40 G4, G6, G16, G25, G40
Range Ability 1:150 or better 1:150 or better 1:150 or better 1:150 or better
Permissible errors of ±3% (Qmin to 0.1 Qmax) ±3% (Qmin to 0.1 Qmax) ±3% (Qmin to 0.1 Qmax) ±3% (Qmin to 0.1 Qmax)
Process indication ±1.5% (0.1 Qmax to Qmax) ±1.5% (0.1 Qmax to Qmax) ±1.5% (0.1 Qmax to Qmax) ±1.5% (0.1 Qmax to Qmax)
Condition
Accuracy Class 1.5 1.5 1.5 1.5
Operating Pressure Up to maximum of 500 mbar (g) 300 mbar (g) 300 mbar (g) 300 mbar (g)
Zinc plated steel and suitable Suitable for outdoor / Indoor Suitable for Indoor /Out Door Suitable for Indoor /Out Door
Casing / body coating on inside and outside for Installation, tamper proof and corrosion Installations,tamper proof and Installations,tamper proof and
corrosion protection of casing resistant powder coated steel casing Corrosion resistance steel Corrosion resistance steel.
Arrow (left to right) Embossed on top of the meter Marked on body Marked on body Marked on body
Fire Resistance As per BS EN 1359 EN 1359:2007/ BS 4161 or equivalent As per BS EN 1359 As per BS EN 1359
All the Meters shall be tested for Meter pressurized with air at
Tests Meter pressurized with air at 1.5 Meter pressurized with air at 1.5
external leak tightness and 1.5 MAOP of the meter,
External leak tightness test. MAOP of the meter, immersed in water MAOP of the meter, immersed in
resistance at 1.5 times the design immersed in water for
for observance of leakage water for observance of leakage
pressure observance of leakage
Mechanical pressure loss,
As per EN 1359 2 mbar 2 mbar 2 mbar
mean pressure loss test.
Ability of the meter to
Carried out Carried out Carried out Carried out
generate pulses.
AMR Required Required Required Required
Each meter shall have in-built Meter shall be provide with a
All Meters shall have in‐built reverse All Meters shall have in‐built
Reverse flow reverse count restrictor, as per device to prevent the reverse
count restrictor reverse count restrictor
BS EN 1359. rotation of index.
Others
All meter internals should be Metering equipment shall be
Each meter has to be sealed and Metering equipment shall be sealed &
prevented from tampering against sealed & Tamper Proof and
Sealing arrangement any signs of tampering should Tamper Proof and have shall be able to
any third party objects like have shall be able to prevent &
be clearly evident prevent & detect tampering
magnet, etc. detect tampering
MGL Tech spec BS 4161: Part 5: 1990 EN 1359: 1998 IS 14439 (Part 1): 1997 & (Part 2): 1998
Clause Clause Clause
Test type Test Features/parameters Test type Clause No. Test Features/parameters Test type Test Features/parameters Test type Test Features/parameters
No. No. No.
+/- 2% at any rate of flow between the +/-3% for flow rate of Qmin to +/-3% for flow rate of Qmin to 0.1 Qmax and
Accuracy of Errors of Maximum 6.1 (Part
9.1, App. P badged rating and any rate of flow not 5.1 0.1 Qmax and +/-1.5% for flow +/-1.5% for flow rate bet. 0.1 Qmax and
registration indication permissible errors 2)
less than 1/50 th of the badged rating. rate bet. 0.1 Qmax and Qmax. Qmax.
For meter with working pr. less than 75 Residual deformation of the
mbar, no leakage till int. pr. of 115 unpressurized meter case shall be
mbar. For meters with working pr. bet less than 0.75% of the linear
Cases shall be gas-tight up to the maximum
75 mbar & 7 bar, hydrostatic test at 5 dimension over which it is
Resistance to 4.2.3 (Part working pressure of the gas meters. If meters
Soundness test App.N. times the max. working pr. for 30 min 6.2.3 measured. Maintain test pr. equal Soundness of cases
internal pressure 1) are to be installed in the open air, they shall be
without significant yeilding followed to 1.5 times the max working pr.
impermeable to runoff water.
by pneumatic test at 1.1 times the max for 30 min. Rate of
working pr. for 10 min. Rate of change pressurization / depressurization
of pr. shall be less than 350 mbar/s. shall not exceed 350 mbar/sec.
Feet 5.4 Min. ht of feet shall be 5 mm. Insulating feet 6.5.2 Minimum height of 5 mm.
Supply air to meter at pr. of 50 mbar. Furnace temp. 650 deg C, Test
Fire Temp.of furnace is incr. by 821 deg C Resistance to high period: 30 min. Temp. of furnace
6 As per BS 4161 or eqvt Fire resistance App. T 6.5.5
resistance in 30 mins. and leakage rate is ambient temp. shd. be raised as per curve
monitored & recorded. defined in ISO 834: 1975.
Mechanical Mechanical
Type Tests 10 7
performance performance
Exercise the meters in a test rig
Pass air at a flow rate equal to badged using a distributed gas at temp. G 0.6 to G 10 (maximum flow rate, 2000 hrs
rating for 30 min. & then at flow rate of bet. 15 deg C and 25 deg C and 8.2.3.1 within 100 days); G 16 to G 650 (minimum
Endurance Tests 10.1 & App. R. Endurance test 7.1.2.2 Durability test
115% of its badged rating for 135 days pr. not exceeding the max. (Part 2) flow rate of 0.5 Qmax, 2000 hrs within 180
at 20 deg C. working pr. for a period of 5000 days)
hrs at Qmax.
Test of components
4.4.3.4
in meter
Std. Devn. Of 8.2.1.2 0.2% for flow rate less than 0.1 Qmax and
errors of indication (Part 2) 0.1% for flow rate bet. 0.1 Qmax and Qmax.
Center to
center 2 110 mm
distance
Pressure
3 As per BS 4161 or eqvt
test point
Torque value
Bending Moment
Resistance to vibrations 6.2.6
For maximum flow rate of 1-10 cu.m/h, ht. of dropping the meter is 0.5
m; for 16-65 cu.m/h, it is 0.3 m; for 100 & 160, it is 0.2 m.
Any blistering of the coating shall be less thanthat given as the ratio
density 2/size 2 in ISO 4628-2:1982, and the deg. of corrosion shall not
be greater than that given as Ri 1 in Table 1 of ISO 4628-3:1982.
5 periods each of 8 hrs duration using a sun lamp that has been in use
for 50-400 hrs.
As per EN 60730-1:1995.
BS 4161: Part 5: 1990
Test type Clause No. Test Features/parameters
Appendix S &
Ambient temp. range -5 deg C to 35 deg C
3.3
Extreme temperatures App. S & 3.3 -15 deg C to 40 deg C
+/-3% for flow rate of 0.1 Qmax and +/-1.5% for flow rate bet. 0.1
Errors of indication 5.1
Qmax and Qmax.
Salt spray test App. E 2.4 As per BS 3900: Part F 4
No penetration of surface for movement of test apparatus over surface at
Test of scratch resistance App. B.2
30-40 mm/s with a spring force of 9.8 / 29.4 N.
App. B-3 &
Penetration Criteria Visually / Microscopic examination / salt spray test.
4.2(a)
100% humidity, 42-48 deg C, Test Period - 4 days. No evidence of
Test for resistance to humidity App. C.
lifting,blistering or deterioration.
Tests on diaphragm. 4.4.3.3
Immersion in toulene + heptane at 20 deg C for 7days. Change in areas
a) Liq. phase immersion test
less than 5%. No delamination, no blistering.
Immersion in distilled water at 20 deg C. for 7 days. Change in area less
b) Water test
than 5%. No delamination, no blistering.
c) Low temp. flexibility 4.4.3.3.3 & App.
Stiffness at -5 deg C after 20 mins shall be less than 25%.
(Torsion test of stiffness) F.
Apply air at pr. of 25 mbar at under side of test piece. No bubbles shd.
d) Porosity test App. G.
occur after 1min.
Test of components in meter 4.4.3.4
Test Period - 264 hrs. Rel. Hummidity - 85%. Gas flow rate shd. not be
a) Vapour Phase Test 4.4.3.4.1
less than 30 cu. dm/h (1 cu.ft/h).
400 hr on air at 0.5 Qmax at -5 deg C followed by 400 hr on air at 0.5
b)Ambient temp. test. 4.4.3.4.2
Qmax at 35 deg C.
Index windows 4.5
a) Visual Inspection No crazing/blisters. Viewing Portion shd. be transparent.
Window fitted on meter should withstand a force at 200N without
b) Rigidity
touching any moving part of the mechanism.
At -5 deg C, window shd. withstand the impact of 25 mm dia solid steel
c) Impact
ball dropped 3 times from a ht. of 350 mm.
Test piece should not glow or flame for more than 5 secs. Mat. dropped
d) Flammability from specimen shall not burn. Charred /scorched area shall be less than
20% & less than 50mm.
For meter with working pr. less than 75 mbar, no leakage till int. pr. of
115 mbar. For meters with working pr. bet 75 mbar & 7 bar, hydrostatic
Soundness test App.N. test at 5 times the max. working pr. for 30 min without significant
yeilding, pneumatic test at 1.1 times the max working pr. for 10 min.
Rate of change of pr. shall be less than 350 mbar/s.
+/- 2% at any rate of flow between the badged rating and any rate of
Accuracy of resistance 9.1
flow not less than 1/50 th of the badged rating.
Total mean pr. Loss 9.2,App.Q. 2 mbar to 4 mbar.
Mech. Pr. Loss 9.3 & App. Q 0.6 to 1 mbar
Type Tests 10
Pass air at a flow rate equal to badged rating for 30 min. & then at flow
Endurance Tests 10.1 & App. R.
rate of 115% of its badged rating for 135 days at 20 deg C.
The gas meters made by Hangzhou Beta Gas meter Co., Ltd.,
which are printed with polyester powder plastics coating, have
more stronger ability to against the heavy humidity and rainfall.
There is a gas flow direction mark on top case of the meter and
also a prevent-reverse hook inside of the meter against the illegal
dismantle and stealing and reverse installation.
-200C to +400C
G1.6 H225xW195xD170 mm
G1.6 2.0 kg
We can supply the meter with fire resistance according to
BS4161 part 5
OK, we can print the Custom name on the index, but you should
provide your marks for our design the new nameplate.
In our export packing, we often use one individual box for each
meter and six boxes in one master carton, and 42 cartons on one
pallet with nylon plastic wrapped, to avoid the impact and
Valid ISO 9001 issued by raining.
TUV management Service GmbH
(Germany)
1 Scope
2 Normative references
3 Terminology
4 Definitions
5 Symbols
6 Working conditions
7 Flow range
8 Maximum working pressure
9 Temperature range
10 Climatic Enviroment
11 Metrological performance
12 Errors of indication
13 Pressure absorption
14 Starting flow rate
15 Metrological stability
16 Overload flow rate
17 Environment and humidity
18 Influence of other devices
19 Cyclic volume
20 Construction and materials
21 General
22 Robustness
23 Corrosion protection
24 Resistance to storage temperature range
25 Optional features
26 Mechanical performance
27 Meter assembly
28 Index
29 Diaphragms and other components in the gas path
30 Marking
31 All meters
32 Two-pipe meters
33 Durability and legibility of marking
34 Meters supplied for testing
35 Production requirements for gas meters
Diaphragm gas meters provided with a built-in mechanical gas temperature
36
conversion device
37 Integral battery powered temperature conversion device
38 Additional tests for meters to be used in open locations
39 Durability
40 Bibliography
Table 10
Error of Indication
Pressure absorption
Starting flow rate
Metrological stability
Overload Flow Rate
Environment and humidity
Influence of other devices
Cyclic Volume
External leak tightness
Resistance to internal pressure
Meter case sealing
Connections
Resistance to vibration
Resistance to impact
Resistance to mishandling
Resistance to storage temperature range
Pressure measuring point
Insulating feet
Magnetic index drive
Reverse flow devices
Resistance to high ambient temperature
Durability
Meter error of indication at declared
ambient temperature limits
Index
Toluene/iso-octane vapour test
Water vapour test
Ageing test
Marking
Error of indication where the temperature of the gas at the meter inlet is
significantly different from the ambient temperature of the air surrounding the
meter
Humidity
Weathering
NOTE 1 In the column marked *, the number of meters required is dependent on the size of meter being tested and whether
NOTE 2 Several plaques are required for testing to 6.3, corrosion protection.
NOTE 3 “X” indicates those tests which are applicable to all meters and “Y” indicates those extra tests which are applicable
Clause No. Parameters
2
3
3.1
3.2
4
4.1
4.2
4.3
4.4
5
5.1
5.2
5.3
5.4
5.5
5.6
5.7
5.8
6
6.1
6.2
6.3
6.4
6.5
7
7.1
7.2
7.3
8
8.1
8.2
8.3
9
Annex A
(normative)
Annex B
(normative)
Annex C
(normative)
Annex D
(normative)
Annex E
(informative)
Annex F
(informative)
Annex ZA
(informative)
Test Sequence
Number of meters required for test purposes
Clause number
1 1 1 1
5.1 or B.2.1 X X X
5.2
5.3 X
5.4 X
5.5
5.6
5.7
5.8
6.2.2 X X X X
6.2.3
6.2.4
6.2.5
6.2.6
6.2.7
6.2.8
6.4 X
6.5.1
6.5.2
6.5.3
6.5.4 Y
6.5.5 Y
7.1.2 or B.2.2
7.1.3
7.2
7.3.2 X
7.3.3 X
7.3.4 X
8 and B.3 if
applicable
B.2.3
F.1
dependent on the size of meterF.2being tested and whether option 1 or option 2 has been chosen (see Table 7).
rotection.
s and “Y” indicates those extra tests which are applicable if an optional extra is fitted to the meter.
rs required for test purposes
6
1 1 2 1 1
Maximum*
X X X X
X X X
1 OF 2
X
2 OF 2
X X X X X
X
X
X
X
X
X
Y
Y
Y
X
X
X
Y
Y