a) Coal b) Solar c) Hydro d) Thermal 2. Fishes respire through a) Lungs b) Nose c) Heart d) None 3. Harshavardhana was defeated by a) Kirtivarman b) Pulakesan – 1 c) Pulakesan-II d) None 4. Konark Sun temple is situated in a) Karnataka b) UP c) Odisha d) Bihar 5. Out if the four persons “B” is taller than “C” and “A” is taller then “D” but not as tall as “C” who among then is the tallest a) A b) B c) C d) D 6. Rs.900 are distributed among A, B and C in the ratio 4:5:6 what will be the difference of the shames of A and C. a) 25% b) 120% c) 130% d) 150% 7. The father is 7 times alder than his son. After 4 years, the some of their ages would be 50 years. The Son’s age at present is. a) 5 years b) 6 years c) 5¼ years d) 9 years 8. A cistern is filled in 9 hours and it takes 10 hours when there is a leak in its bottom. If the cistern is full, then in what hours shall the leak empty it? a) 80 hrs b) 85 hrs c) 90 hrs d) 95 hrs 9. In a class of 25 students the average age in 25 years. If the teacher’s age is also included, then the average age increases by one year. What is the age of the teacher? a) 40 b) 51 c) 41 d) 57 10. In a zoo there are rabbits and pigeons. If their heads are counted, these are 90 while their legs are 224. Find the number of pigeons in the Zoo. a) 68 b) 70 c) 72 d) 80 11. The average daily wages of X, Y and Z are Rs.120. If Y earns Rs. 40 More than Z and X earns double of what Z earns, then the wages of X per day are a) 80% d) 120% c) 160% d) 100% 12. The number of Images of an object formed by two mirrors included at an angle of 60° is a) 6 b) 5 c) 4 d) 7 13. Which organ of the body is affected in typhoid? a) stomach b) kidney c) lungs d) Intestine 14. Plaster of Paris is obtained from a) Limestone b) silica c) Bauxite d) Gypsum 15. If the radius of a circle is increased by 6% then its area is increased by a) 0.36% b) 12.36% c) 36% d) 3.6% 16. If there metallic spheres of radii 6cm, 8cm and 10cm are melted to form a single sphere then the diameter of the new sphere will be a) 12 cm b) 24 cm c) 30 cm d) 36 cm 17. Complete the series A B C C B A D E F F E D G H I _____________ a) I b) H c) G d) J 18. J K M P ___________ a) T b) U c) V d) W 19. A C E G : B D F H : : P R T Y :? a) Q R U M b) Q S U M c) S T U R d) Q R S T 20. The most likely code for “Trivandrum” is a) 5691291717 b) 8256713249 c) 9162732548 d) 6612468937 21. 17, 19, 23, 29 _________ a) 33 b) 31 c) 34 d) 37 22. Pick the odd one out. a) cube b) Cone c) Cylinder d) Trapezium 23. Aryabhatta was a famous __ of ancient India a) Doctor b) Poet c) Physicist d) Mathematician 24. The full form of “ISRO” is a) International Space Research Organisation b) Indian Salt Research Organisation c) Indian Space Research Organisation d) None 25. Which one of the following is the oldest veda. a) Rigveda b) Atharva veda c) Yajur veda d) None 26. Red blood corpuscles are formed in a) Heart b) Bone marrow c) Liver d) Kidney 27. Which of the following is the ore of iron? a) Haematite b) Magnetite c) Bauxite d) Smalite 28. Hari starts from his house and walks 200 meters East and Then goes North for 80 meters, then West for 40 meters and finally South for 80 meters. He Stops here. How for is he from his house. a) 100m b) 150m c) 160m d) 80m 29. Pick odd one out a) Copper b) Tin c) Zinc d) Brass 30. A and B married Couple. X and Y are Brothers, X is the brother of A. How is Y related to “B”? a) Brother – in – law b) sister – in – law c) Mother – in – law d) None 31. The area of a Square is ‘X’ if its sides is doubled then its area will be. a) x2 b) 2x c) 4x d) x2/2 32. The compound interest on 4000/- at the rate of 10% for two years is. a) 840/- b) 820/- c) 780/- d) 860/- 33. Which one of the following numbers has got the highest value? a) 53/4 b) 25/6 c) 127/25 d) 121/9 34. A device which Converts AC into DC known as a) Transformer b) Amplifier c) Rectified d) Stabilize 35. A person who does not speak too much a) candid b) outspoken c) Reticent d) Defiant 36. The resistance of a 100 watt 230V lamp is a) 52.9Ω b) 529Ω c) 2.3Ω d) None 37. If a 1000 watt heater is used for 5 hours, then the cost of energy @ Rs. 1.50 per unit will be a) Rs.1.50 b) Rs.15 c) Rs.225 d) Rs. 7.50 38. Which rectifier requires four diodes a) Half wave b) Full wave c) Bridge d) None 39. Difference between the synchronous speed and the induction motor speed is called. a) Regulation b) Slip c) Backlash d) lag 40. The time period of Sinusoidal wave at standard frequency in India is a) 1 sec b) 0.1 sec c) 0.2 sec d) 0.02 sec, 41. Core of the transformer is made of a) Iron b) copper c) low silica steel d) high Silica Steel 42. Thread angle of Acme thread a) 60° b) 45° c) 90° d) 29° 43. “Die” is used for a) To make the thread b) Knurling c) Drilling d) Inside threading 44. Angle of centre punch a) 30° b) 45° c) 60° d) 90° 45. Why annealing is done a) Soften the metal b) Harden the metal c) Remove internal Stress d) None 46. The least count of Vernier bevel protractor a) 5 sec b) 1° c) 5 minutes d) 90° 47. Surface plate is commonly used for checking a) Surface b) Right angle c) Angle d) 60° angle 48. Bench vice spindle has a) V –threads b) Acme threads c) Square threads d) Buttress threads 49. The least count of Micrometer is a) 0.02mm b) 0.1mm c) 0.01mm d) 0.001mm 50. Claw hammer is mostly used in a) Fitter trade b) Tool & Die c) Black Smithy d) Carpentry 51. Outside caliper is used to measure a) 90° angle of the job b) Outer diameter of round Job c) Inside diameter d) All of these 52. Sine bar is an instrument used for accurate measurement of a) Length of the job b) Dia. of the job c) Depth of the hole d) none 53. Lip clearance angle in a drill is kept a) 30° b) 45° c) 37° d) 15° 54. On lathe, to support heavy rods while turning we use a) Dead centre b) Tail stock c) Steady d) Carrier 55. B.S.W thread has thread angle of a) 60° b) 45° c) 37° d) 55° 56. The maximum efficiency of full wave rectifier is a) 40% b) 81.2% c) 90% d) 98% 57. In full wave rectifier if the input frequency is 50 Hz then the output frequency is a) 50 Hz b) 100 Hz c) 200 Hz d) 400Hz 58. A “Zener diode” is used as a a) Rectifier b) Breakdown voltage c) Voltage regulator d) Forward characteristic 59. A “PNP” transistor is made of a) Germanium b) Silicon c) Either Ge (or) Si d) None 60. With the rise in temperature of a P – N Junction which of the following will increase? a) Width of depletion layer b) Junction barrier voltage c) Reverse leakage current d) All of these 61. A “thyristor” is often used in a) Wall clock b) Digital multi meter c) Speed control of motor d) None 62. Indentify the operation that is not normally done on a lathe a) Knurling b) Threading c) Tapering d) Cutting a square 63. Shafts transmitting power at right angle to each other are connected by a) Helical gear b) Spur gear c) Bevel gear d) Spiral gear 64. Which of the following is more viscous lubricating oil? a) SAE 20 b) SAE 30 c) SAE 40 d) SAE 50 65. The color code of 47kΩ ± 20% resister will be a) Orange, Blue, Yellow, Silver b) Yellow, Violet, Orange c) Yellow, Violet, Orange, Silver d) Yellow, violet, Orange , Gold 66. The unit of capacitance is a) Ohm b) coulomb c) farad d) Volt 67. “Meggar” is used to measure a) Low conductor resistance b) High insulation resistance c) Both d) None 68. LED have a) Resistance b) PN junction c) NPN transistor d) PNP transistor 69. The mixture of solder wire is a) tin + zinc b) Zinc + lead c) Tin + lead d) None 70. The voltmeter is connected to a) Parallel b) Series c) Both d) Direct method 71. Grinding wheals are made by a) Iron & stone b) Rod & sand c) Sand d) abrasive & bond 72. Which of the following is needed while marking on Round Job? a) Bolt b) Block c) V-block d) C-clamp 73. The ratio of the timings of the cutting stroke and idle stroke a) 3:2 b) 2:3 c) 1:3 ` d) 2:1 74. C = ? × (F – 32) a) 5/9 b) 9/5 c) 7/a d) 9/7 75. Name the correct name of hole in the hammer a) Round hole b) Eye hole c) Blind hole d) Taper hole 76. The operation called to increase the diameter by forging in known as. a) Jumping b) Clamping c) Flat making d) end sitting 77. Type of hammer used in heavy work. a) Ball pane b) Cross pane c) Sledge d) None 78. Angle of flat chisel for cutting steel a) 30° b) 40° c) 50° d) 60° 79. A draft is used for a) Making holes b) Opening holes c) Enlarging holes d) Closing holes 80. Method of preparing the pieces of metal for welding is known as a) Scarf ring b) Fullering c) up-setting d) Swaging 81. In resistance welding the electrodes used are of a) Consumable type b) Non – Consumable type c) Both a and b c) None 82. In gas welding process the gas used for Combustion is a) Nitrogen b) CO2 c) O2 d) Acetylene 83. Which type of joint is not used in welding process? a) Fillet Joint b) Twist Joint c) V – butt d) Lap Joint 84. To fix regulator on acetylene gas cylinder which thread is used? a) Right hand b) left hand c) Square d) Cotton thread 85. The oxy – acetylene flame used for welding low melting point metal is a) Neutral b) Oxidizing c) Reducing d) Cutting 86. The process of making permanent type of joints in steel section is called a) Soldering b) screw fitting c) Pressing d) welding 87. Steel rails are welded by a) Gas welding b) Thermit welding c) Resistance welding d) Argon are welding 88. Tesla is the unit of a) Flux b) Field strength c) flux dressily d) None 89. The voltage drop across a 1 kw electric heater element of resistance 50Ω. Where hot is a) 100 volt b) 200 volt c) 300 volt d) None 90. Two condensers of capacity 2F and 3F are connected in Series and a third condenser of 1F is connected in parallel to them. The resultant capacity will be a) 11/5 F b) 5/11 F c) 5/6 F d) 6 F 91. One Newton – meter is equal to a) One watt b) One joule – ampere c) One volt ampere d) One joule. 92. As compared to an amplifier, a transformer cannot a) Increase the output voltage b) Increase the output Current c) Increase the output Power d) None 93. Most essential instrument required by a T.V Technician a) Voltmeter b) Ammeter c) Multi meter d) Ohm meter 94. In drilling operation feed is expressed in a) mm b) mm/sec c) mm/min d) mm/revolution 95. _____ is the process of coating Zinc by hot dipping a) Anodizing b) Basing c) Galvanizing d) None 96. Bronze is all alloy of a) Copper and Zinc b) Copper, Zinc and tin c) Copper and tin d) None 97. Light year is the unit of a) Time b) Distance c) Light d) Intensity of light 98. The storage batteries are rated in a) Amp – V.lt b) Amp – sec. c) Watt – hrs d) Amp-hrs 99. How are electric circuits protected from over heating? a) Thermo couple b) Shunts c) Fuses d) Solenoids 100. There resistors of 3Ω, 10Ω, and 15Ω are connected in parallel to a 30 V circuit the current that will flow through the 3Ω resistor is a) 30A b) 10A c) 6A d) 2A ANSWERS 1. a 27. a 53. d 79. b 2. d 28. c 54. a 80. a 3. c 29. d 55. d 81. b 4. c 30. a 56. b 82. c 5. b 31. c 57. b 83. b 6. b 32. a 58. c 84. b 7. c 33. d 59. c 85. a 8. c 34. c 60. d 86. d 9. c 35. c 61. c 87. b 10. a 36. b 62. d 88. c 11. c 37. d 63. c 89. d 12. b 38. c 64. d 90. a 13. c 39. b 65. d 91. d 14. d 40. d 66. c 92. c 15. b 41. d 67. b 93. c 16. b 42. d 68. b 94. d 17. a 43. a 69. b 95. c 18. a 44. d 70. a 96. b 19. b 45. c 71. d 97. b 20. b 46. c 72. c 98. d 21. d 47. a 73. a 99. c 22. d 48. c 74. a 100. b 23. d 49. c 75. b 24. c 50. d 76. d 25. a 51. b 77. c 26. b 52. d 78. d