Beruflich Dokumente
Kultur Dokumente
ERRATA
Copyright ASME International Document provided by IHS Licensee=saipem sa/5956362001, 11/03/2004 06:08:38 MST
Provided by IHS under license with ASME Questions or comments about this message: please call the Document Policy Group
at 303-397-2295.
A M E R I C A N S T A N D A R D
Microscope
ASA B1.11-1!58
UDC 621.882.082:535.822:681.42
, \
$ ..
1
- r /?LShLed 6y
--`,```,``,```,``,`,,,````,``-`-`,,`,,`,`,,`---
T H EA M E R I C A NS 0 C l E T . Y OF MECHANICAL ENGINEERS
- ~ ....
.~
N. Y.
~~ ~ ~
.-: ~ ~~ ~
. _
Copyright ASME International Document provided by IHS Licensee=saipem sa/5956362001, 11/03/2004 06:08:38 MST
Provided by IHS under license with ASME Questions or comments -about
r this message: please call the Document Policy Group
at 303-397-2295.
" .
ASME B L - L Z 5 8 m 0 7 5 7 b 7 0 0037888 T W
Foreword
The standardizationof the microscope objective thread is one of the projects toward unification
of screw thread standards among inch-using countries. In Great Britain, the Royal Microscopical
Society had established standards for microscope objectives in 1858, based on the Whitworthscrew
thread system, which were subsequently used throughout the world. The history of this standard
isin the Transactions of the Society: 1858,p. 39; 1859,p.92;1896, pp. 389,487; 1911, p. 175;
1915, p. 230; 1924, p. 266; and 1936, p. 377.
In.practice, American manufacturers of this thread have always employed modifications of the
Whitworth form because of their preference for flat crests, such modified threads being completely
interchangeable with the RMS threads. At the Conference on Unification of Engineering Stand-
ards held in Ottawa, 1945, the American Delegation resented ASA Paper B1/57 and A.O. Drawing
K
ED-95 giving limits of size for a truncated Whitwort thread. Since a thread form with rounded
crest is preferred in Great Britain for optical instruments, it was recommended that thetitle of this
document be amended to read, “Proposed Permitted Truncation andTolerances for RMSThread.”
On the basis of this proposal a draft of a proposed American Standard, dated April, 1948, was cir-
culated to the B1 Sectional Committee membership for comment. In conformity with comments
received, a revised draft, dated October, 1954, mas approved by Subcommittee No. 4 on Instrument
Screw Threads and subsequently submitted to theSectional Committee for approval. Final approval
as an American Standard was given on January 7, 1958, by ASA.
--`,```,``,```,``,`,,,````,``-`-`,,`,,`,`,,`---
Any part o f this standard may be quoted. Credit lines should read: “Extractedfrom American
Standard Microscope Objective Thread (ASA Bl.11-1958) with the permission of the publisher, The
American Society o f Mechanical Engineers, 29 W. 39th St., N e w York 18, N. Y.’’
Copyright ASME International Document provided by IHS Licensee=saipem sa/5956362001, 11/03/2004 06:08:38 MST
Provided by IHS under license with ASME Questions or comments about this message: please call the Document Policy Group
at 303-397-2295.
ASME B L - L L 5 8 m O 7 5 7 6 7 00 0 3 7 8 8 7 L 9
--`,```,``,```,``,`,,,````,``-`-`,,`,,`,`,,`---
K. E. Faiver, Senior Design Engr., Olds Motor Div., General Motors Corp., Lansing, Mich.
R. F, Frye, Mgr., Materials & Stds. Dept., Westinghouse Electric Corp., East Pittsburgh, Pa.
I. H. Fullmer, Chief, Engineering Metrology Sec., National Bureau of Standards, Washington, D. C.
W. H. Gourlie, Standards Engr., The Sheffield Corp., Dayton, Ohio
V. C. Meigs, Engineering Dept., Autonetics, a division of North American Aviation, Inc., Bellflower, Calif.
D. R. Miller, 3521 36th St., N.W., Washington, D. C.
J. H. Miller, Vice-Pres., Weston Electrical Instrument Corp., Newark, N. J.
D. V. Peroni, Commander, WCXPS, Wright Air Development Center, Wright-Patterson Air Force Base, Ohio
H. W. Robb, Manager, Company Standards, Engineering Services Div., General Electric Co., Schenectady, N. Y.
E. H. Schaeffer, Chief Engr., Elgin National Watch Co., Elgin, Ill.
M. A. Schultheis, Staff Engr., Systems Development Lab., Hughes Aircraft Co., Culver City, Calif.
C. E. Smart, Works-Mgr., W, & L. E. Gurley, Troy, N. Y.
C. S.Tallman, Development Physicist, American Optical Co., Instrument Div., Buffalo, N. Y.
S . B. Terry, Orient, L. I., N. Y.
K. T. Vande, Chief Draftsman, Bausch & Lomb Optical Co., Rochester, N. Y,
D. F. Viles, President, Waltham Screw Co., Waltham, Mass.
P. F. Weber, Asst, to Pres., Kollsman Instrument Corp., Elmhurst, Long Island, N. Y.
Copyright ASME International Document provided by IHS Licensee=saipem sa/5956362001, 11/03/2004 06:08:38 MST
Provided by IHS under license with ASME Questions or comments about this message: please call the Document Policy Group
at 303-397-2295.
A S M E ~ 1 . 1 1 ,5 8 m 0757b70 0037870 8 m
American Standard
--`,```,``,```,``,`,,,````,``-`-`,,`,,`,`,,`---
Copyright ASME International Document provided by IHS Licensee=saipem sa/5956362001, 11/03/2004 06:08:38 MST
Provided by IHS under license with ASME Questions or comments about this message: please call the Document Policy Group
at 303-397-2295.
A S M E BL.33 5 8 m 0 7 5 7 6 7 0 0039893 T
AMERICAN STANDARD.
Property Dimension
Symbol Formula
BASICTHREAD
FORM
angle
Half angle of thread”
Included of thread”
a
2a
...
e..
2790’
55’00’
incha Number of threads per n 36
Pitch iil; O . 027778
Height
triangle
thread
of fundamental
Height of basic
PH
hb
O ,960491~
O.640327~
0.026680
O ,0178
Radius at crest and root of British Standard
Whitworth basic thread (not used) r O,137329~ 0.0038
DESIGNTHREAD
FORM
Height of truncated
Whitworth
thread k hb - u 0.566410~
0.0157
Width of flat at crest F, 0.243624~ O, 0068
Width of flat at root F, 0.166667p O .M46
Basic truncation of crest from basicWhit-
worth form U O.073917~ O.00205
BASICAND DESIGNSIZES
D ... o 800
u
Dn D 0.800
4 D-2U-G O . 7941
E D-6s O.7822
En D-hb O .7822
2K n D-hb-G
D -2hb
D”2k
O . 7804
O .7644
O.7685
diameter
Minor of external threadb K. D-2hs-G O.7626
Allowance at pitch (effective) diamete+ G ... 0.0018
All other dimensions are given in inches.
6 An allowance equal to that on the pitch diameter is also provided on the major and minor diametersof the external thread
for additional clearance and centralizing.
c Allowance (minimum clearance)on pitch (effective) diameter is the same as on British RMS thread.
10 Lead of Thread. Thethread isof the mum limit of the major and minor diameters may
single (single-start) type. be increased bytheamount of the allowance.
11 Classification. There is established Benefits are derived principally from changes in
herein only one class of thread which experience the major diameter where increasing both limits
has proved to be adequate to meet the demands improves the depth of threadengagement, and
of the applications. increasing only the maximum limit grantsa larger
12 Nominal Sizes. There is only one nomi- manufacturing tolerance. However, unless such
nal size having a basic major diameter of 0.800 deviations are specifically covered in purchase
inch and a pitch of 0.027778 inch (36 threads per negotiations,it is to be assumed that the threads
inch). will be supplied in accordance with the tables in
this standard.
13 Allowances. Positive allowances -(mini-
14 Tolerances. In accordancewithstand-
R‘
mum clearances) are provided on the Itch, major,
ard practice, tolerances on theinternalthread
--`,```,``,```,``,`,,,````,``-`-`,,`,,`,`,,`---
Copyright ASME International Document provided by IHS Licensee=saipem sa/5956362001, 11/03/2004 06:08:38 MST
Provided by IHS under license with ASME Questions or comments about this message: please call the Document Policy Group
at 303-397-2295.
b.
MICROSCOPE OBJECTIVE THREAD
practicable, Adequatedepth of thread engage- 16 Limits of Size. The limits of size for
ment is thereby assured. both the external and internal thread are given
All tolerances are given in Table 2.
in Table 2. Their application is illustrated in
15 LengthsofEngagement. The toler- Fig. 1.
ances specified herein are applic?ble to lengths of
engagementranging from '/S Inch to a/8 inch 17 ThreadDesignation. This screw thread
(approximately 15 to 50 per cent of the basic shall be designated on engineering drawings,in
diameter). Lengths of engagement exceeding specifications, and on tools and gages by thesym-
these limits are seldom employed and, conse- bol "AMO" preceded bythe basic major diameter
quently, are not proyidedfor in thls standard. in inches and the number of threads per inch, as
For microscope objective assemblies the length
of engagementmost generally employed is '/S given below :
inch. O . 800-36 AMO
--`,```,``,```,``,`,,,````,``-`-`,,`,,`,`,,`---
Element
, Max Min To1 Max Min To1 Max Min To1
.External thread 0.7941
0.7911
0.0036 0.7804 0.7774
0.0030
0.7626 0.7552b
Internal thread O . 80%" O.8000 :0.7852
0.7822 0.0050 0.7715
0.7685
0.0030
aAU dimensions are given in inches.
Extreme minimum minor diameter produced by a new threading tool having a minimum flat of p/12 (E 0,0023 inch).
This minimum diameter is not controlled by gages but by the form of the threading tool.
C Extreme maximum major diameter produced by a new threading tool having a minimum flat of p/20 (E 0.0014 inch).
This maximum diameter is not controlled by gagesbut by the form of the threading tool.
Copyright ASME International Document provided by IHS Licensee=saipem sa/5956362001, 11/03/2004 06:08:38 MST
Provided by IHS under license with ASME Questions or comments about this message: please call the Document Policy Group
at 303-397-2295.
AMERICAN STANDARD
INTERNAL THREAD
(NU T )
T- ,
'/z Major Diameter Af/owance
on Exitferna/ thread
L
--`,```,``,```,``,`,,,````,``-`-`,,`,,`,`,,`---
EXTERNAL THREAD
(%RE W )
FIG.1 DISPOSITION
OF TOLBRANCBS,
ALLOWANCES,
AND CREST FOR AMO THRBAD
CLEARANCES
Copyright ASME International Document provided by IHS Licensee=saipem sa/5956362001, 11/03/2004 06:08:38 MST
Provided by IHS under license with ASME Questions or comments about this message: please call the Document Policy Group
at 303-397-2295.
MICROSCOPE OBJECTIVE THREAD
Appendix
Recommended Gage Dimensions of MicroscopeObjective Thread
0.800-36 AMO
Dimension
Symbol Description Formula Dimension
--`,```,``,```,``,`,,,````,``-`-`,,`,,`,`,,`---
“Go SETTING”THREAD PLUG
GAGE(A-Go)
D,,Max Major diameter, maximum D,Max O,7941
D,,Min Major diameter, minimum ’ D,, Mag - 0.0004 O.7937
E,, Max Pitch (effective) diameter, maximum E. Max O .7804
E,, Min Pitch (effective) diameter, minimum E,, Max - 0.0002 O ,7802
“NOT Go SETTING”THREAD PLUGGAGE(A-NOT GO)
D,,Min Major diameter, minimum D. Max O. 7941
D,,Max
E,, Min
Major diameter, maximum
Pitch (effective) diameter, minimum
D,, Min 0.0004
E. Min
+ O.7945
O,7774
Eo Max Pitch (effective) diameter, maximum E,, Min O .O002 + O . 7776
“Go” THREAD RING GAGE(G-Go)
Eo Max Pitch effective diameter, maximum E,, Max “Go” A Plug O.7804
E,, Min Pitch !effective] diameter, minimum E,, Min “Go” A Plug O .7802
Kg Max Minor diameter, maximum D, Min - 2hs O.7644
KOMin Minor diameter, minimum KOMax - 0.0004 O.7640
“NOT GO” THREAD RING GAGE(%NOT GO)
Eo Min Pitch (effective) diameter, minimum Eo Min “Not Go” A Plug o 7774
*
E,, Max Pitch (effective) diameter, maximum E,, Max “Not Go” A Plug O.7776
. K,Min Minor diameter, minimum E. Min - p/3
0.7681
K,,Max Minor diameter, maximum KOMin 4- O .o004 0.7685
“Go” THREAD PLUG
GAGE(C-Go)
D,,Min Major diameter, minimum D, Min 0.8000
D,,Max
E,, Min
MaJor diameter, maximum
Pitch (effective) diameter, minimum
D,,Min 0.0004
E , Min
+ 0.8004
O.7822
E,, Max Pitch (effective) diameter, maximum Eo Min 0.0002 + O.7824
“NOTGo” THREAD PLUG
GAGE(C-NOT Go)
D,,
Max
DoMin
E , Max p / 3
DoMax - O.OOO4
+ O.7945
O. 7941
E,, Max E,, Max 0.7852
E,, Min Eo Max - 0.0002 O. 7850
..........................................................
Tolerance in lead.. f 0.0002 in.
...........................................
Tolerance on half-angle of thread. f O deg 20 min.
NOTE: Ring and plug gages made in accordance with the above dimensions are not suitable for checking British product,
the rounded roots of which mill not pass the flat crest truncations of the gages. However, British gages, which are made to
check the full Whitworth form of thread, will accept American product.
Copyright ASME International Document provided by IHS Licensee=saipem sa/5956362001, 11/03/2004 06:08:38 MST
Provided by IHS under license with ASME Questions or comments about this message: please call the Document Policy Group
at 303-397-2295.
American Standardfor Screw Threads and Threaded Parts
TITLE OF STANDARD PRICE
Microscope Objective Thread (B1.11-1958). ............................................. $1O
.O "
Unified and American ScrewThreads for Screws, Bolts,Nuts, and Other Threaded Parts (Bl.1-
-1949) (Third Edition, published in 1951). ............................................ 3.50
Screw Thread Gages and Gaging (B1.2-1951). ........................................... 4.00
Aune Screw Threads (B1.5-1952). ..................................................... 2.25
Nomenclature, Definitions, and Letter Symbols for Screw Threads (B1.7--1949; reaffirmed
--`,```,``,```,``,`,,,````,``-`-`,,`,,`,`,,`---
1953). ............................................................................ 1.50
Stub Acme ScrewThreads (B1.8-1952) ................................................. 1.50
Buttress ScrewThreads(B1.9-1953). .................................................. 1.50
Pipe Threads(B2.1-1945). ........................................................... 2.50
Small Solid Rivets (B18.1-1955). ...................................................... 1.so
Square and Hexagon Bolts and Nuts and Lag Bolts (B18.2-1955). .......................... 2.00
Socket HeadCap Screws and Socket Set Screws (B18.5-1954). ............................. 1.50
Large Rivets-1/2 In. Diameter and Larger (B18.4-1950; Reaffirmed 1957). ................. 1 S O
Round Unslotted Head Bolts (B18.5-1952). ............................................. 1.50
Slotted and Recessed Head Wood Screws (B18.6.1-1956). .............................. 1.00
Hexagon and Slotted Head Cap Screws, Square Head Set Screws, Slotted Headless Set Screws
(B18.6.2-1956) ................................................................... 1S O
Plow Bolts (B18.9-1950). ............................................................ 1.50
Track Bolts and Nuts(B18.10-1952). .................................................. 1S O
Fire-Hose Coupling Screw Threads (B26-1925; reaffirmed 1953). ........................... 1.o0
Hose CouplingScrew Threads (B33.1-1935; reaffirmed 1947). ............................. 1.o0
Preferred Limits and Fitsfor Cylindrical Parts (B4.1-1955). ............................... 1.50
Quantity discounts asfollows: In lots of lO,ZO% of list; 50, 2.5%; 100,30%.
A binder is availablef o r holding these standards. It holds tweenty-$ve (2.5) pamphlets and gives every ad-
vantage o f a bound book together with the added convenience which comesfrom the ability to instant4 insert,
remove, or transpose sections ofthe contents. Price $3.25 Postpaid.
A complete list o f American Standards published by the American Society of Mechanical Engineers 06-
tainable upon request.
A S M E members are entitledto a 20 per cent discount on a single copy o f any standard.
Copyright ASME International Document provided by IHS Licensee=saipem sa/5956362001, 11/03/2004 06:08:38 MST
Provided by IHS under license with ASME Questions or comments about this message: please call the Document Policy Group
at 303-397-2295.