Beruflich Dokumente
Kultur Dokumente
Wireless Intercom Access
Model:200A
Open the Door By Auto-rejected Phone Calls By Authorized Numbers;
Up to 200 Authorized Phone Numbers, Special for Apartments;
User Friendly Design, No more Wiring Installation;
High Quantity Two-way Voice Communication.
SPECIFICATIONS:
Quad-band 850/900/1800/1900Mhz;
FREE Charge. Open the Door By Auto-rejected Phone Calls By Authorized Numbers
Every Family has a Admin Password and Authorize 5 Family Phone Numbers ;
Affordable Rates with Top Quality. No More Wiring Installations and other Complex Accessories;
2 Relay Outputs (NC/NO),Well compatible with Electronic Locks and DVR Camera;
12VDC Power Supply, Relay Time Editable (1~300 seconds). Default“0s”, means not work ;
110
123 29,6 13
276
246
3
SETTINGS:
1) Open the unit's back cover and insert the SIM card.(B1, B2)
2) Wiring connect refer to the picture (D1).Then switch on the device, LED displays .
2 Jumper
B2 C1 C2
SIM CA
RD
3 Wiring Contactor
Basic Settings:
Attention: Some countries like Chile , need add country code “ +56” before cell phone
number when set up.
√ Authorized administrator phone number
4
1) Press “#” → → Enter the admin password (6 digits, default: 123456) → Press “#” to confirm
2) Enter “0000#” → → Use the admin mobile to call the device phone number →
setting succeed. Auto back to the setup interface after 1 second, continue the settings or press “*” to
1) By keyboard:
Press “#” → → Enter “admin password#” → → Enter the “room number#” (E.g.:
“0101#”), → → Enter “1#” → . , use the family admin phone number to call
in → means successful, Auto back to the setup interface after 1 second, continue the settings or
2) By SMS Command:
① Authorized 1house host in 1 SMS: Administrator send “#room number#1#house host phone number” to
the device.
② Authorized 2 or more house host in 1 SMS: Administrator send “#room number#1#house host phone
number#room number#1#house host phone number” to the device.(Max: Authorized 5 phone numbers in 1 SMS).
√ Delete the Authorized House Host phone number and the door operate password:
1) By keyboard:In setup interface , enter the “Room number#” E.g. : “0101#” → , → “0#”
→ means successful. Auto back to the setup interface after 1 second, continue the settings or press
5
1) By keyboard:In setup interface , enter the “4#” (Default: Enter the room number, it will dial all
authorized phone numbers and hang up after short ring. Enter “5#”, it will dial all the Authorized phone
numbers circularly until someone reject it, or answer the phone to create 2-ways communication.) →
means successful.During the talking ,press cell phone”0”to open door. Auto back to the setup
interface after 1 second, continue the settings or press “*” to return when it displays .
2) By SMS command: Administrator send the SMS command “#4(or #5)” to the device. If get message “Admin
set OK” means set up successfully
√ Setting the Relay Working Method (SMS Only):
1) Administrator send the SMS command “#6#1#NO#2#NC” to the device. ( “NO,NC” can be changed by user)
Remark: “6” means setting the relay, “1” means the relay 1, “2” means the backup relay 2, “NO” means the
relay Normal Open, “NC” means the relay Normal Close.
√ Setting the Relay Working Time:
1) By keyboard:In setup interface , enter the “#6#1#working time#” to setting the relay 1 working time,
(Enter “#6#2#working time#” to setting the relay 2 working time,range 1~300 Seconds,when setting “0”
means don’t work), → means successful. Auto back to the setup interface after 1 second, continue
1) By keyboard: In setting status , enter the “7#” ,displays (The device will send the SMS to
the administrator, including the GSM modules’ IMEI code and the GSM signal),after that, will be ,
6
The device will be back to the setting status after 1 second, shows , can change the other setting or
press “*” to standby state.
2) By SMS Command: The Administrator send the SMS “#7” to the device.
If successfully, the device will return the IMEI code and the GSM signal.
√ Delete All The Authorized Phone Number(SMS Only):
1) Administrator send the SMS command “#Administrator password CLRALL” to the device. (E.g. :
“123456CLRALL”, then all the Authorized phone number will be deleted)
√ Authorized the door operate password and family phone number by House Host number (SMS Only):
1) Change or add the door operate password:House host send the SMS command “Room Number#6#(add or
change)password” to the device.
Basic Operation:
Administrator:
5) By phone call: The device will open the door and rejected the call, .means successful.
Visitors:
Installation:
1) Dig a trench for the device (E1 ,references dimension:248*112*33mm ).
2) Open the outlet holes for wirings ( E2 ,3 outlet holes for wirings ① ② ③).
E1 E2
1
Type 1:
Type 2:
① Short contact the “R” and “G” in “J4” by the jumper ( C2),
② Power on the device
③ After 3 seconds, pull out the jumper and removed it to “J6”(C1).
④ The device will be reset to the default setting, all the authorized number will be removed.
Remove the jumper from J6(C1)to GR (C2), and plug it back to J6 after reset successfully (C1).
Please refer to page 3 picture .