Beruflich Dokumente
Kultur Dokumente
IP Camera
DVR IP Camera
the same as the selected direction
Switch
IP Camera DVR
Wireless Bridge
Passive PoE Adapter supports up to 60 meter S M
IP Camera ---- Wireless Bridge Wireless Bridge ---- DVR ---- Monitoring PC IP Camera --Switch --Wireless Bridge Wireless Bridge--- DVR ---Monitoring PC
equiring environment :
3.Bridge Ways (*Two bridge ways: WDS Key Bridge & LED Display Bridge, choose the way based on request.)
Web Configuration
S M S M
After IP address configuration, connect to CPE’s wireless SSID: Wireless 5.8G, and input password (Default Password: 66666666)
Master CPE Slave CPE
Master CPE Slave CPE
2.PC configuration if PC connect CPE wired 3. Login Web Configuration 4. Configure Wireless
Setup Wizard
If connect PC and CPE wired, Set PC local network IP to 192.168.188.x Use IE browser to access http://192.168.188.253, pop up the login page shown
(x: 2--250), same network segment as CPE, subnet mask: 255.255.255.0: below,input the login password: admin, enter into the home page.
Current Mode Network Connection Details Wieless Network Status
Decription
Transmission Control Protocol/Internet Protocol.The default Alternate DNS server: . . .
CPU Usage
Lan IP 192.168.188.253
AP BSSID
AP BSSID
N/A
N/A
SSID
Channel
Wireless5.8G
44
Configuration method
According to the quickly setup wizard of each mode shown in the above figure, set the parameters
Subnet 255.255.255.0
widearea network protocol that provides communication AC Address 192.168.188.1
AP BSSID N/A Encrypt WPA/WPA2PSK_TKIPAES
Memory Usage
across diverse interconnected networks.
Validate settings upon exit Advanced...
Manage
MAC Address 44:D1:FA:4C:D8:AE
AP BSSID N/A MAC Addres 44:D1:FA:4C:D8:B0
andoptions based on user needs, click next until the setting of each step is completed
OK Cancel OK Cancel
4.Channel Table
5.Login WEB by Mobile Phone
1.Login CPE by Mobile phone(Password is admin) Canel yunlink 5.8G Network details OK Canel yunlink 5.8G Network details OK
Trouble Shooting
WLAN 400Mbps Gateway 192.168.82.1
None PROXY
Wireless Bridge Regional
CONNECTED
yunlink 5.8G
None > Channel Code Instructions Trouble Reason Solution
Connected fe80:528f:4cff:fef5:7bd6
192.168.82.199
IP SETTINGS 1.Wireless Interference 1.Use Wi-Fi analysis to choose the best channel,
yunlink
Saved 255.255.255.0 or change to 5G CPE
Static > 2.Distance is too long,or there are some
Working Mode: Super WDS running time 00:32:12 Packet Latency
AVAILABLE NETWORKS 192.168.82.1
bar between them 2.CPE should be in normal distance,and avoid bar
IP address 192.168.188.70
click to setup location information 3.CPE’s angle in wrong direction, weak signal 3.Adjust the angle of CPE according to signal strength
123456789 Gateway 192.168.188.253
BDCOM-0000 prefix length 24 1.Press reset button in 10 seconds to reset device, the
1.Forget password
DNS 1 8.8.8.8 default password is admin
ON
BRCE 2.4G Wrong password 2.Input wrong password
Super Intelligent DNS 2 8.8.4.4
3.Too much cookie
2.Re-input the password
BV_2_4G-200 3.Clear cookie,run arp -d to clear MAC table.
IP settings
Modify network
BV_5_8G-200 > DHCP 1.Local IP is not in the same network segment 1.Ping 192.168.188.253 to see connection status
Forget network of CPE 2.Stop other devices or change to another IP
channel9 Static Can not login
2.IP is taken by other devices 3.Check LAN Connection and Ethernet cable
WEB
Login 3.LAN Connection or Ethernet cable has problem 4.Clear cookie,run arp -d to clear MAC address
4.Too much cookie, MAC address haven’t update
Setup Wizard System Status
Android system setup steps 1.PoE power supply is not working 1.Check if POE Adapter or POE switch work
WiFi Setup More Functions 2.Some problem in CPE’s PoE port 2.Check if POE port of CPE is OK
System LED 3.Ethernet cable is loose, RJ45 port is wrong 3.Check if Ethernet cable is loose,if Ethernet cable
light off Power current/voltage lower or wrong plugged in to POE port
4.Check if voltage is normal ,if socket has problem, if
input voltage of POE adapter is normal
2.Configure Static IP address for mobile phone after connect with CPE 1.Packet Latency 1.Adjust the distance, angle and channel to decrease
Settings WI-FI Back Configure IPv4
by wireless Settings
2.Ethernet cable circuit latency
Wi-Fi Automatic Low transmission 3.Network virus attack 2.Check if there is circuit in the network
Search
FR3800-X5-MESH-5.8G Manual
Rate 4.Too much access users 3.Check if port isolated to avoid network virus and
Unsecured Network
BootP broadcast storm
①Static IP address configuration on Android Mobile Phone Jessy WU CHOOSE A NETWORK...
4.Decrease the access users.
JW MANUAL IP
Open settings in phone, turn on WLAN and find the SSID of the CPE, touch it for a long time Apple ID,iCloud,iTunes&App Store
BDCOM_0000 IP Address 192.168.188.30 1.Static electricity 1.Make CPE or POE adapter need ground connection
Apple ID Suggestions
until there is a menu, then choose”static IP” in the menu, set the mobile phone IP address as BV_2_4G-200
BV_5_8G-200
Subnet Mask 255.255.255.0
Device always 2.Running time too long 2.Running time over 7 days, reboot it
Router 192.168.188.253
dead 3.Lightning stroke 3.After lightning,device POE port broken or unstable,
192.168.188.X (X can not be 253 or 252), same network segment as CPE, subnet mask: Airplane Mode
HP-Print-35-LaserJet Pro MFP
better to deploy lightning conductor .
Wi-Fi yunlink 5.8g
255.255.255.0, then gateway, subnet mask and domain . Bluetooth On
M1 5G test
NIS-HomeAP-5G_519C
1 2 3 4 5 6 7 8 9 0
Cellular szjk5
Wireless 2.4G-11111 ,
②Static IP address configuration on IOS Mobile Phone
Personal Hotspot Off
#+= . , ? !
Wireless 5.8g-22222
VPN
Open settings and choose Wi-Fi, connect with CPE, click exclamation mark , manual to set IP Carrier CHINA MOBILE
yunlink ABC space return
address 192.168.188.X (X can not be 253 or 252) and subnet for mobile phone, note: mobile
phone’s IP address should be same network segment as CPE.