Beruflich Dokumente
Kultur Dokumente
C-Series C2
Firmware Version 5.02.19.0008
January 2015
INTRODUCTION:
This document provides specific information for version 5.02.19.0008 firmware for the following products:
Extreme Networks recommends that you thoroughly review this document prior to
installing or upgrading this product.
For the latest firmware versions, visit the download site at:
http://support.extremenetworks.com/
FIRMWARE SPECIFICATION:
F0615-O
CUSTOMER RELEASE NOTES
F0615-O
CUSTOMER RELEASE NOTES
BOOTPROM COMPATIBILITY:
MGBICs Description
MGBIC-LC01 1000Base-SX, IEEE 802.3 MM, 850 nm Short Wave Length, 220/550M, LC SFP
MGBIC-LC03 1000Base-SX-LX/LH, MM, 1310 nm Long Wave Length, 2 KM, LC SFP
Extended 1000Base-LX, IEEE 802.3 SM, 1550 nm Long Wave Length, 110KM,
MGBIC-LC07
LC SFP.
MGBIC-LC09 1000Base-LX, IEEE 802.3 SM, 1310 nm Long Wave Length, 10 KM, LC SFP
MGBIC-MT01 1000Base-SX, IEEE 802.3 MM, 850 nm Short Wave Length, 220/550 M, MTRJ SFP
MGBIC-02 1000Base-T, IEEE 802.3 Cat5, Copper Twisted Pair, 100 M, RJ45 SFP
MGBIC-08 1000Base-LX/LH, IEEE 802.3 SM, 1550 nm Long Wave Length, 80 KM, LC SFP
MGBIC-LC04 (C3Ks only) 100Base-FX, IEEE 802.3 MM, 1310 nm Long Wave Length, 2 KM, LC SFP
MGBIC-LC05 (C3Ks only) 100Base-FX, IEEE 802.3 SM, 1310 nm Long Wave Length, 10 KM, LC SFP
XFPs Description
10GBASE-ER-XFP 10GBASE-ER, IEEE 802.3 SM, 1550 nm Long Wave Length, 40 KM, LC XFP
10GBASE-LR-XFP 10GBASE-LR, IEEE 802.3 SM, 1310 nm Long Wave Length, 10 KM, LC XFP
10GBASE-SR-XFP 10GBASE-SR, IEEE 802.3 MM, 850 nm Short Wave Length, 33/82 M, LC XFP
10GBASE-CX4-SFP 10GBASE-CX4, IEEE 802.3 Twin Axial, Copper SFF-8470, 15 M, LC XFP
10GBASE-ZR-XFP 10GBASE-ZR, SM, 1550 nm Long Wave Length, 80 KM, LC XFP
NOTE: Installing third party or unknown pluggable ports may cause the device to malfunction and will void your
warranty.
SUPPORTED FUNCTIONALITY:
F0615-O
CUSTOMER RELEASE NOTES
F0615-O
CUSTOMER RELEASE NOTES
Note:
As a best practice, Extreme Networks recommends that prior to upgrading or downgrading the firmware on your
switch, you save the existing working configuration of the system by using the show config outfile
configs/<filename> command. Please note that you will need a copy of your 5.01.xx.xxxx configuration if you need
to back-rev from 5.02.xx.xxxx to the previous firmware version.
The C2 most likely will not be shipped to you pre-configured with the latest version of software. It is strongly
recommended that you upgrade to the latest firmware version BEFORE deploying any new switches. Please refer
to http://support.extremenetworks.com/ for the latest firmware updates to the C-Series C2 and follow the TFTP
download instructions that are included in your Configuration Guide.
Soft copies of the Configuration Guide are available at no cost on the Extreme Networks web site,
http://support.extremenetworks.com/.
The C2 family of stackable switches is managed by a single IP address for a stack of up to 8 switches.
In order to download the new software to a stack of C2 switches, simply follow the instructions to upgrade a
switch with new software. The system will then automatically download the new software to all the members in the
stack controlled by that stack manager.
Additional steps are required when upgrading from 1.xx.xx software to 2.xx.xx or higher software versions. These
steps will not be required in subsequent releases.
F0615-O
CUSTOMER RELEASE NOTES
The stack will reset, the current config will be cleared, the new image will start up, and the stack will automatically
program itself with the previous configuration.
If the CLI is monitored during this process, the user will see that all Diffserv commands will display error
messages stating the command is unknown. This message should be ignored and is for information only.
Upgrading from the 2.00.48 release to the 2.01.20 release requires some additional steps for users who utilize
GVRP. When upgrading to the 2.01.20 image, the user should only reconfigure GVRP on inter-switch links (ISLs).
GVRP was enabled by default in the 2.00.48 image on all edge ports; only non-default commands are displayed
in the config, so only the set GVRP disable commands would be listed in a config file created in a 2.00.48 image.
In the 2.01.20 image, the situation is the opposite. Any “GVRP disable” commands are ignored. For any ports on
which the user wants GVRP “enabled”, the user must log back in and reconfigure those ports to “enable”. Any
ports which the user wants to be “disabled” will require no action.
Configuration files that were created in the 1.xx.xx track can be applied to a switch/stack using the 2.xx.xx track,
however the steps defined above for configuring GVRP must be observed.
Use the “copy tftp://<tftp server IP>/<path>/<image name> system:image” command to download the new
Release 3 image. This image is downloaded, sent to all stack members, and marked as a “backup” code
image. If this download to any of the stack members is unsuccessful, an error message should be
generated.
3. Issue the “show version” command to verify that the new Release 3 code image exists on all stack
members as the “backup” image. If not, you should manually push this code to any stack member that is
not properly updated using the “set switch copy-fw” command.
4. Once all stack members contain the new software image, use the “set boot system <image name>”
command to set the newly downloaded image as the “active” image.
5. Stack will reboot using the updated code.
If you have a unit that is running Release 2 or older software, and you want to use the unit in a stack running
Release 3 software, you must boot the unit as a standalone unit and update its code to Release 3 before cabling
it into the existing stack.
F0615-O
CUSTOMER RELEASE NOTES
Directly upgrading from 4.00.xx to 5.02.03.xxxx or above is supported. However, you must follow the
instructions below for upgrading from 4.00.xx to 5.02.02 or below.
Important Note:
You cannot upgrade directly from 4.00.xx to 5.02.02 or below. You must first upgrade to 5.01.xx.xxxx, then upgrade
to 5.02.02 or lower.
The following steps are required for the upgrade to succeed:
Policy Capacities
Maximum supported roles per system 255
Maximum number of rules per role 100
Maximum unique rules per system 100 - C2Hs
Maximum number of masks per port 10
Maximum number of unique masks per system 18 - C2Hs
Maximum policy users per port 2 (PC + Phone)
Router Capacities
The following table defines the router capacities:
Feature Capacity
ARP Dynamic 2024
ARP Static 512
Route Table 2500
OSPF Areas 4
Total OSPF LSA Type 2500
OSPF LSA Type 1 – Router Links No restriction can equal 2500
OSPF LSA Type 2 – Networks Links No restriction can equal 2500
OSPF LSA Type 3 – Summary Networks No restriction can equal 2500
OSPF LSA Type 4 – Summary ASBRs No restriction can equal 2500
OSPF LSA Type 5 – AS External Links No restriction can equal 2500
OSPF LSA Type 7 – NSSA External Links No restriction can equal 2500
OSPF LSA Type 9 – Opaque Subnet-only Not Supported
OSPF LSA Type 10 – Opaque Area Not Supported
OSPF LSA Type 11 – Opaque AS Not Supported
OSPF ECMP paths 4
Static routes 64
RIP routes 2500
IP Interfaces 24
Secondary Interfaces 31
F0615-O
CUSTOMER RELEASE NOTES
Feature Capacity
VRRP Interfaces 20
IP Helper Address 6 per interface
Access Rules (inbound only) 100
Access Rules – Per ACL 9
IGMP Groups 256
IGMP Snooping Static Entries 100
DVMRP Routes 256
Note:
Starting with 5.02.03, the firmware includes a new PoE driver which will require additional bootup time as the driver
is being updated on PoE units within the stack. Once the initial boot of the code has completed and the PoE driver
is updated, the delay should not be seen again.
Note: Firmware 5.02.12 and beyond support installations using 5 meter cables.
F0615-O
CUSTOMER RELEASE NOTES
F0615-O
CUSTOMER RELEASE NOTES
F0615-O
CUSTOMER RELEASE NOTES
F0615-O
CUSTOMER RELEASE NOTES
F0615-O
CUSTOMER RELEASE NOTES
F0615-O
CUSTOMER RELEASE NOTES
F0615-O
CUSTOMER RELEASE NOTES
F0615-O
CUSTOMER RELEASE NOTES
Due to hardware limitations, the forced-auto mode is not supported on ports belonging to the C2H models.
Auto, mdi and mdix modes are supported. By default, Extreme Networks switch devices are configured to
F0615-O
CUSTOMER RELEASE NOTES
Normal = normal
Open = no cable attached to port
Short = detection of an inter-pair short
Fail = unknown error or crosstalk
Detach = for ports on stack units no longer present, but were previously connected
Not Supported = ports other than 1GE RJ45 ports
This command is only supported on RJ45 copper connections running at 1GE speeds.
F0615-O
CUSTOMER RELEASE NOTES
F0615-O
CUSTOMER RELEASE NOTES
F0615-O
CUSTOMER RELEASE NOTES
F0615-O
CUSTOMER RELEASE NOTES
F0615-O
CUSTOMER RELEASE NOTES
F0615-O
CUSTOMER RELEASE NOTES
F0615-O
CUSTOMER RELEASE NOTES
F0615-O
CUSTOMER RELEASE NOTES
F0615-O
CUSTOMER RELEASE NOTES
F0615-O
CUSTOMER RELEASE NOTES
F0615-O
CUSTOMER RELEASE NOTES
F0615-O
CUSTOMER RELEASE NOTES
F0615-O
CUSTOMER RELEASE NOTES
F0615-O
CUSTOMER RELEASE NOTES
F0615-O
CUSTOMER RELEASE NOTES
For the most up-to-date information concerning known issues, go to the Global Knowledgebase section at:
http://support.extremenetworks.com/.
Title
ctbroadcast mib
ctRatePolicing mib
ctQBridgeMIBExt mib
01/08/2015 P/N: 9038198-23 Subject to Change Without Notice Page: 32 of 34
F0615-O
CUSTOMER RELEASE NOTES
Title
ctCDP mib
ctAliasMib
ctTxQArb mib
ctDownLoad mib
etsysRadiusAuthClientMIB
etsysRadiusAuthClientEncryptMIB
etsysPolicyProfileMIB
etsysPwaMIB
etsysSyslogClientMIB
etsysConfigurationManagementMIB
etsysMACLockingMIB
etsysSnmpPersistenceMIB
etsysMstpMIB
etsysMACAuthenticationMIB
etsysletfBridgeMibExtMIB
etsysMultiAuthMIB
etsysSntpClientMIB
etsysIeee8023LagMibExtMIB
etsysVlanAuthorizationMIB
etsysCosMIB
etsysResourceUtilizationMIB
Enterasys Networks Private Enterprise MIBs are available in ASN.1 format from the Extreme Networks web site at:
www.extremenetworks.com/support/policies/mibs/. Indexed MIB documentation is also available.
F0615-O
CUSTOMER RELEASE NOTES
GLOBAL SUPPORT:
By Phone: 603-952-5000
1-800-872-8440 (toll-free in U.S. and Canada)
By Email: support@enterasys.com
By Web: www.extremenetworks.com/support/
For information regarding the latest software available, recent release notes revisions, or if you require additional
assistance, please visit the Extreme Networks Support web site.
F0615-O