Beruflich Dokumente
Kultur Dokumente
General Information
Vo l t a g e s e t t i n g / P a g e u p U - S E T . t S . fl H U
to choose/Shortcut extract .1.44 inch color 1/.lUft
LCD screen |I SKI
Ml data group |s our .17. IKIU
W , i H l p M U - S E T. s
s
ocr
orr
\:7. ^Hrt
mi iu
c v
M I'KE m\ orr 9
Store value into the
specified data group
ysa 12.ooa| all buttons
06.09Ai
The actual value
of output current" Constant voltage and constant iHIJSM-PREjib,
"current status prompt
The actual value
n z Data set prompt
of output power "
Preset over-voltage— S - O U P : 3 2 . 0 0 U
Preset over-current— S - 0 C P : 1 2 . 2 H A
Preset over-power— S OPP:390.4U ^
current and the actual output power. Input voltage is on the bottom of the
screen. There are some running status icons on the right of the screen,
key lock icon, abnormal output status icon, constant voltage and constant
current icon, data set tip icon and opening or closing output icon.
Set the output voltage and output current on the main interface.
Press I v/f i key shortly, you can enter into voltage setting status. Then
m u m press the coding potentiometer, and then enter to adjust the numerical value.
Press coding potentiometer to enter into the status of adjusting the
^SiSM/r^±ia. .1. 44T)-gfe numerical value you want to adjust. Turn coding potentiometer to adjust the
^ M 7F P numerical value. Turn by clockwise rotation to increase the numerical value;
Turn by counterclockwise to decrease the numerical value. If you want to
r™ 24. 99V t A exit adjusting the numerical value, press shortly I v/t I . In the same time the
S 12.00Ai W ■m m m m / m
preset value will be stored. Or you can do nothing in one minute, the status
6/it iS M/1^ T jS „_ will be automatically existed and the preset will be stored too. You can
JF^ItttS press [aTTI to set the output current by the same way.
Set the data on the data setting interface
e: B w B w J On the main Interface, you can press |Set| shortly to enter into data setting
interface. On the data setting interface, press shortly |v/t| or | A/f | to page
up or page down to U-SET or l-SET, and then set the output voltage and
^ET145.04| 15.10 - l t t i i ^ , ; ; 1 t i a ^ fl output current by same way used in the main interface .
Set the protection value.
45.d4Vi 0 U T: 2 4 . 9 8
Page up or page down to S-OVP, S-OGP or S-OPP place l l - S E T : 2 5 . 0 0 U
to set over-voltage value , over-current value and over-power I-SET:12.10A ^
11 . 9 9
lit±i^/ii^i>p!iJil=
06.09A| n z
ta J±/1'a >1 "-K iS le 7F
value correspondingly; when the value is up to the setting
value, output will be closed. And then press shortly the
coding potentiometer to enter into the status of adjusting
S-OUP:32.00U ®
S-OCP:12.Z0ft ^
S-OPP:390.40
B-LED4
n-PRE:«0 OFF "
^
I S E T I s h o r t l y, y o u c a n e x t r a c t t h e s p e c i fi e d d a t a g r o u p y o u n e e d . i
t a i l .