Beruflich Dokumente
Kultur Dokumente
D2PAK Surface Mount Power Package Motorola Preferred Device
The D2PAK Power Rectifier employs the Schottky Barrier principle with a
platinum barrier metal. These state–of–the–art devices have the following
features:
SCHOTTKY BARRIER
• Center–Tap Configuration
RECTIFIER
• Guardring for Stress Protection
30 AMPERES
• Low Forward Voltage 45 VOLTS
• 150°C Operating Junction Temperature
• Epoxy Meets UL94, VO at 1/8″
• Guaranteed Reverse Avalanche
• Short Heat Sink Tab Manufactured — Not Sheared! 4
• Similar in Size to the Industry Standard TO–220 Package
1
Mechanical Characteristics 4 1
3
• Case: Epoxy, Molded 3
• Weight: 1.7 grams (approximately) CASE 418B–02
• Finish: All External Surfaces Corrosion Resistant and Terminal D2PAK
Leads are Readily Solderable
• Lead and Mounting Surface Temperature for Soldering
Purposes: 260°C Max. for 10 Seconds
• Shipped 50 units per plastic tube
• Available in 24 mm Tape and Reel, 800 units per 13″ reel by
adding a “T4” suffix to the part number
• Marking: B2545T
Rev 2
Rectifier Device
Motorola, Inc. 1996 Data 1
MBRB2545CT
ELECTRICAL CHARACTERISTICS (PER LEG)
Rating Symbol Value Unit
Maximum Instantaneous Forward Voltage (2) (iF = 30 Amps, TJ = 125°C) vF 0.73 Volts
(iF = 30 Amps, TJ = 25°C) 0.82
Maximum Instantaneous Reverse Current (2) (Rated dc Voltage, TJ = 125°C) iR 40 mA
(Rated dc Voltage, TJ = 25°C) 0.2
(2) Pulse Test: Pulse Width = 300 µs, Duty Cycle ≤ 2.0%.
200
i F, INSTANTANEOUS FORWARD CURRENT (AMPS)
100
100
70
Figure 1. Typical Forward Voltage, Per Leg Figure 2. Typical Reverse Current, Per Leg
PF(AV), AVERAGE FORWARD POWER DISSIPATION (WATTS)
32 32
IF(AV), AVERAGE FORWARD CURRENT (AMPS)
SQUARE WAVE
28 TJ = 125°C 28
IPK DC
24 (RESISTIVE LOAD) =π 24
IAV
DC
20 20
5
(CAPACITIVE SQUARE
16 LOADS) 16
10 WAVE
12 12
IPK
= 20 RATED VOLTAGE APPLIED
8 IAV 8
RθJC = 1.5°C/W
4 4
0 0
0 4 8 12 16 20 24 28 32 36 40 110 120 130 140 150
IF, AVERAGE FORWARD CURRENT (AMPS) TC, CASE TEMPERATURE (°C)
0.74
18.79
0.065
1.651
0.420
10.66
0.07
1.78
0.14 inches
0.330 3.56 mm
8.38
205° TO 219°C
PEAK AT
200°C
170°C SOLDER JOINT
DESIRED CURVE FOR HIGH
MASS ASSEMBLIES 160°C
150°C
150°C
SOLDER IS LIQUID FOR
40 TO 80 SECONDS
100°C 140°C (DEPENDING ON
100°C MASS OF ASSEMBLY)
C
E NOTES:
V 1. DIMENSIONING AND TOLERANCING PER ANSI
B Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
4
INCHES MILLIMETERS
DIM MIN MAX MIN MAX
A 0.340 0.380 8.64 9.65
A B 0.380 0.405 9.65 10.29
S C 0.160 0.190 4.06 4.83
1 2 3
D 0.020 0.035 0.51 0.89
E 0.045 0.055 1.14 1.40
G 0.100 BSC 2.54 BSC
–T– K H 0.080 0.110 2.03 2.79
SEATING J 0.018 0.025 0.46 0.64
PLANE K 0.090 0.110 2.29 2.79
G J S 0.575 0.625 14.60 15.88
V 0.045 0.055 1.14 1.40
H
D 3 PL
STYLE 3:
0.13 (0.005) M T PIN 1. ANODE
2. CATHODE
3. ANODE
CASE 418B–02 4. CATHODE
ISSUE B
Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding
the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and
specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters which may be provided in Motorola
data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals”
must be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights of
others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other
applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury
or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola
and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees
arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that
Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal
Opportunity/Affirmative Action Employer.
Mfax is a trademark of Motorola, Inc.
How to reach us:
USA / EUROPE / Locations Not Listed: Motorola Literature Distribution; JAPAN: Nippon Motorola Ltd.; Tatsumi–SPD–JLDC, 6F Seibu–Butsuryu–Center,
P.O. Box 5405, Denver, Colorado 80217. 303–675–2140 or 1–800–441–2447 3–14–2 Tatsumi Koto–Ku, Tokyo 135, Japan. 81–3–3521–8315
Mfax: RMFAX0@email.sps.mot.com – TOUCHTONE 602–244–6609 ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park,
INTERNET: http://Design–NET.com 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852–26629298