Beruflich Dokumente
Kultur Dokumente
1
MT 2008 Inglês - 1a Parte.qxd 21/10/2008 11:46 Page 2
2
MT 2008 Inglês - 1a Parte.qxd 14/10/2008 15:27 Page 3
3
MT 2008 Inglês - 1a Parte.qxd 14/10/2008 15:27 Page 4
4
MT 2008 Inglês - 1a Parte.qxd 14/10/2008 15:27 Page 5
VEDACIT RAPIDÍSSIMO 150: setting accelerator and hardener, not alkaline ...................................................69
VEDACIT RAPIDÍSSIMO 200: setting liquid accelerator for mortar and projected concrete .............................70
VEDACIT RAPIDÍSSIMO EM PÓ: ultra-quick setting waterproofing material for shot concrete and mortar.......71
VEDACIT RÁPIDO CL: setting and hardening accelerator for concrete and mortar..........................................72
3. Mortar Admixture...........................................................................................75
ALVENARIT: plasticizer admixture for laying and casting mortar .....................................................................77
CONCENTRADO OBE: powder admixture for laying mortar.............................................................................78
EXPANSOR: expanding admixture for wedging mortar....................................................................................79
MIX-OIL: lubricating admixture for blocks and precast pieces.........................................................................80
TRICOSAL: fluidifier for injections in cracks and sheaths................................................................................81
VEDALIT: concentrated plastifying admixture for foundation mortar and rough cast .......................................82
VEDALIT EM PÓ: powder plastifying admixture for mortars............................................................................83
4. Mortar ...........................................................................................................85
ARGAMASSA ESTRUTURAL 240: dry high strength mortar for coatings .......................................................87
ARGAMASSA ESTRUTURAL 250: polymer modified mortar for coatings and repairs ....................................88
ARGAMASSA OBE 500: mortar for restoring..................................................................................................89
ARGAMASSA OBE EXTERIOR AC-II: mortar to put in place tiles and ceramics at outside places...................90
ARGAMASSA OBE INTERIOR AC-I: mortar to put in place tiles and ceramics at inside places.......................91
GRAUTH SG: mortar for work with micro-concrete ........................................................................................92
V-1 GRAUTH: high strength mortar for grouting .............................................................................................93
V-1 GRAUTH S: self compacting mortar for micro-concreting........................................................................94
V-1 GRAUTH TIX: high resistance dry mortar .................................................................................................95
V-2 GRAUTH: high strength expansive mortar for grouting .............................................................................96
5. Curing Agents ................................................................................................97
CURING: curing agent for concrete.................................................................................................................99
CURING PAV: curing agent for concrete pavements .....................................................................................100
TRI-CURING: curing agent for concrete pavements ......................................................................................101
6. Form Removal..............................................................................................103
CERA DESMOLDANTE OTTO: for precast concrete tracks and metal formwork ...........................................105
DESMOL: form removal agent for apparent concrete....................................................................................106
DESMOL BETONEIRA: form removal agent for metal surfaces.....................................................................107
DESMOL CD: form removal agent for concrete ............................................................................................108
DESMOL RD: superficial demoulding retarder for concrete...........................................................................109
7. Adhesives ....................................................................................................111
BIANCO: adhesive for mortar and roughcasts ..............................................................................................113
BRANCOL A: white glue for glazed tiles........................................................................................................115
COMPOUND ADESIVO: epoxy structural adhesive........................................................................................116
COMPOUND ADESIVO 200: structural adhesive, epoxy base, for humid surfaces........................................117
COMPOUND ADESIVO GEL: high fluidity, epoxy base, structural adhesive ...................................................118
COMPOUND ADESIVO PL: slow structural adhesive, epoxy base.................................................................119
COMPOUND ADESIVO TIX: high viscosity epoxy structural adhesive............................................................120
COMPOUND GRANITO: epoxy base, adhesive for rocks...............................................................................121
COMPOUND INJEÇÃO: epoxy adhesive for cracking and fissures ................................................................122
6
MT 2008 Inglês - 1a Parte.qxd 14/10/2008 15:27 Page 7
8
MT 2008 Inglês - 1a Parte.qxd 14/10/2008 15:27 Page 9
9
MT 2008 Inglês - 1a Parte.qxd 14/10/2008 15:27 Page 10
10
MT 2008 Inglês - 1a Parte.qxd 14/10/2008 15:27 Page 11
11
MT 2008 Inglês - 1a Parte.qxd 14/10/2008 15:27 Page 12
12
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 16:39 Page 13
CARBOLÁSTICO 1
Waterproofing bituminous paint.
13
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 16:39 Page 14
CARBOLÁSTICO 2
Bituminous putty for repairing.
Characteristics Storage
Black colour Stock the product at a covered, fresh, dry and
First Aid: item 2, page 209 ventilated place, out of the reach of children
and animals and away from sources of heat.
Density: 1.18 g/cm³
Basic Composition: asphalt Packaging
Validity: 24 months
• 1 kg can
• 4 kg bucket
CARBOLÁSTICO 2 forms a thick plastic layer • 20 kg bucket
impervious and highly adherent to concrete, • 200 kg drum
mortar and metal.
It is also indicated for repairing cracks in water
towers. After drying, it does not transfer smell or
Personal protective equipment
taste to water. • Safety glasses
CARBOLÁSTICO 2 is supplied ready for use and • Semifacial mask with filter appropriate for
it is applied cold. organic vapour
• PVC gloves
Field of Application • PVC apron
• Repairing cracks in water towers.
• Sealing metal gutters.
Way to use
The surface should be perfectly dry and clean.
Mix before using.
CARBOLÁSTICO 2 is applied as is with a putty
knife over a previous coat of NEUTROL and
letting dry for at least 12 hours.
Cracking repair
Apply a thin layer (1 mm) of CARBOLÁSTICO 2
and press it well. Thereafter place a VEDATEX
(polyester mesh) strip previously impregnated
with NEUTROL, over the crack. If the layer is
totally dry, apply the second coat of
CARBOLÁSTICO 2. Only place water after the
product has dried completely.
Clean the tools using Turpentine or VEDARRÁS.
Approximate consumption
1.3 kg/m²/mm
14
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 15
CARBOLÁSTICO LAJE
Asphaltic mass for waterproofing purposes.
15
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 16
Packaging
• 3.9 kg bucket
• 20 kg bucket
• 200 kg drum
16
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 17
FRIOASFALTO
Bituminous putty for waterproofing.
17
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 18
HIDROASFALTO VEDACIT
Asphaltic emulsion for waterproofing purposes.
18
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 19
Packaging
• 3.9 kg bucket
• 20 kg bucket
• 200 kg drum
19
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 20
ISOLIT
Bituminous putty for insulation.
Field of Application
• Protection of industrial thermal insulation.
• Anti-corrosive insulation (in combination with
glass cloth) for underground piping.
• Protection for acoustic insulation in air
conditioning ducts.
Note: SELADOR ASFÁLTICO OBE is indicated for
use in freezing chambers.
Way to use
The surface should be clean and free of loose
material.
ISOLIT is used as supplied. Apply with a mason's
trowel or putty knife, in 1.5 mm to 2.0 mm
successive thin layers, as soon as the previous
one has dried.
Approximate consumption
700 g/m²/mm
Storage
Stock the product at a covered, fresh, dry and
20
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 21
Characteristics Application
The application of the rug should start at the
Aluminum colour lower point of the surface so that the rug
First aid: item 1 page 209 joining should obey the water outflow direction.
Basic composition: asphalt modified with
polymers equipped with framework and Internal conclusion of the strainer:
covered with aluminum A - Cut a rectangle of the MANTA ASFÁLTICA
Validity: 12 months VEDACIT ALUMÍNIO size 35 cm x 20 cm roll it
up in the form of a cylinder. With the heat of a
MANTA ASFÁLTICA VEDACIT ALUMÍNIO is blowtorch glue 10 cm of the rug at the internal
made with modified asphalt equipped with high part of the strainer (in the pipe), leaving 10 cm
density and resistant polyethylene. This allows of the rug outward.
the product to be of great elasticity without B - With a stiletto cut in strips the MANTA
endangering its uniform dimensions. It has a ASFÁLTICA VEDACIT ALUMÍNIO which
superficial aluminum foil stamped, flexible and remained above the floor level and adhere with
of high resistance, assuring a reflection of the the blowtorch on the primed surface.
UV rays, exempting the mechanical protection Place a piece of the asphaltic rug to the entire
(mortar bed) and allowing a simple and fast diameter of the strainer to be worked on and
making of the waterproof work. cut (in a pizza shape).
It has a thermal and acoustical insulation. C - Adhere the ends of the MANTA ASFÁLTICA
VEDACIT ALUMÍNIO to the internal pipe
Fields of application previously coated performing the inclination.
• Non passable slabs, plain or generally Step by step
inclined. 1 - Stretch out the rolls of MANTA ASFÁLTICA
• Roofs in general (fibercement, mud, zinc, VEDACIT ALUMÍNIO over the surface to be
ecological roofs, etc). treated in the opposite direction of the water
• Gutter pipes and gutters. flow, starting at the point of the strainer, with
• Marquises. the aluminum part facing upward. Place the
• Expansion joints. rugs one on top of the other beying the stripe
of the joining which comes without the
Way to use aluminum coverage for overlapping.
2 - Approach the flame of the blowtorch to the
Preparing the Substract part which will be adhered to the surface
heating the anti adhering polyethylene
The area should be evened, with appropriate sufficiently that it melts and the asphalt thus
falls and rounded edges (half cane) and the remains slightly exposed (taking care that it
surface around the drainage strainers should does not over melt) and apply immediately the
be lowered. Check if the surface does not rug to the primed substract. The aluminized
show, reliefs, rims or cracks which could part should face upward and one should avoid
damage the asphaltic rug. One or two coats of to place the flame of the blowtorch over it.
PRIMER MANTA VEDACIT should be applied
and await the drying of the product. 3 - Perform the inclination, pressing the heated
bricklayers spoon over the joinings, so as to
On the roofs it is not necessary to apply the guarantee a perfect sealing.
primer, but a a thorough pre cleaning should be
carried out and look after the correct laying of 4 - Melt the asphaltic rug against the skirting
the tiles. board going upward 20 cm.
21
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 22
Approximate consumption
- 1.15 m²/m² on slabs
- 1.40 m²/m² on roofs
• PRIMER MANTA VEDACIT: 300 ml/m²
Storage
Stock the product at a covered, fresh, dry and
ventilated place, out of the reach of children
and animals and far away from sources of
heat.
Attention
MANTA ASFÁLTICA VEDACIT ALUMÍNIO
should be applied by specialized professionals.
One recommends care when using the
blowtorch and always use safety equipment.
Packaging
• 3 mm - roll of 10 m²
• 4 mm - roll of 10 m²
22
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 23
Approximate consumption
MANTA ASFÁLTICA VEDACIT POLIÉSTER:
1.15 m²/m²
PRIMER MANTA VEDACIT: 300 m/ m²
Storage
Stock the product at a covered, fresh, dry and
ventilated place, out of the reach of children
and animals and away from sources of heat.
Attention
One recommends care when using the
blowtorch and the use of protective equipment.
MANTA ASFÁLTICA VEDACIT POLIÉSTER
should be applied preferably by specialized
professionals.
The asphaltic rugs should not be used at
places subject to negative pressure, such as
reservoirs and underground pools (see rigid
system).
Packaging
• 3 mm roll of 10 m²
• 4 mm roll of 1o m²
24
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 25
Approximate consumption
MANTA ASFÁLTICA VEDACIT POLIETILENO:
1.15 m²/m²
PRIMER MANTA VEDACIT: 300 ml/m²
Storage
Stock the product at a covered, fresh, dry and
ventilated place, out of the reach of children
and animals and away from sources of heat.
Attention
One recommends care when using the
blowtorch and the use of protective equipment.
MANTA ASFÁLTICA VEDACIT POLIETILENO
should be applied preferably by specialized
professionals.
Packaging
• 3 mm roll of 10 m²
• 4 mm roll of 10 m²
26
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 27
REBOCOL
Waterproofing powder for mortar.
Characteristics Attention
White powder It is always necessary to perform previous tests
First Aid: item 4, page 210 in order to establish the ideal admixture
proportion and its compatibility to the cement to
Density: 0.79 g/cm³ be used.
Basic Composition: mineral filler
Validity: 24 months Packaging
• 14 kg bucket
REBOCOL is an admixture composed of
plasticizers and stearates that react with the free
lime existing in the cement so forming the Personal protective equipment
calcium stearate. This substance is water • Safety glasses
repellent and caps the mortar pores thus making • PVC apron
the mortar waterproof. • Mask with filter against dust
REBOCOL made mortars keep perfectly healthy • Rubber gloves
environments and avoid mould, stains and
efflorescence.
Field of Application
• Preparation of pre-mixed waterproof mortar for
indoor cast and outdoor coating on walls,
floors, reservoirs and brick laying.
Way to use
REBOCOL should at first be dry mixed with
cement and than sand added. Mix well before
adding water.
It is recommended that waterproof mortars be
prepared in a 1:3 cement/sand mix.
For adding REBOCOL to already prepared mortar,
dry mix in a concrete mixer for at least 3 minutes
before softening the mortar.
Approximate consumption
REBOCOL is used in a proportion of 2% on the
mortar weight or 1 kg of REBOCOL to 50 kg of
mortar.
Storage
Stock the product at a perfectly dry and
ventilated place, following the same principles
of storing cement.
27
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 28
Characteristics Attention
Black colour mass Do not swallow and avoid inhaling the vapor.
First aid: item 2, page 209 Maintain the environment ventilated during
Density: 1.47 g/cm³ application and drying. Avoid direct contact
Basic composition: asphalt with the product using protective mask, safety
Validity: 24 months eye glasses and gloves.
Flammable product. Packaging material should
not be re-used neither incinerated.
SELADOR ASFÁLTICO OBE is a waterproof
asphaltic mass specially designed for the
usage in low temperatures. Packaging
SELADOR ASFÁLTICO OBE does not have any • 25 kg bucket
components with chlorine and its consistency
is appropriate to be used with spatula. Personal protective equipment
• Safety glasses
Fields of application • Semifacial mask with appropriate filter for
SELADOR ASFÁLTICO OBE is indicated to form organic vapours
a vapour barrier for thermal insulation work • PVC gloves
utilizing polyurethane or polyestirene foam. • PVC apron
Way to use
Application
Apply pure over dry and clean surfaces, with
spatula or bricklayers spoon. SELADOR
ASFÁLTICO OBE should be applied in
environments with a temperature in the
range of 25 °C.
Approximate consumption
1.5 kg/m²/mm
Storage
Stock the product at a covered, fresh, dry and
ventilated place, out of the reach of children
and animals and away from sources of heat.
28
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 29
VEDACIT
Waterproofing material for concrete and mortar.
29
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 30
Reservoirs Finishing
When coating reservoirs, obey the service order Apply two coats of NEUTROL after the tank is
indicated on the sketch. 1:3 (cement: sand) mix completely dry.
and 2 kg of VEDACIT/cement bag (50 kg). c) Dar uma chapada de 1 cm de espessura no
Desempenar a última chapada. Nunca queimar, piso, apertá-la e jogar areia em camada fina.
nem alisar com desempenadeira de aço ou
colher de pedreiro. Foundations and thrust walls
A minimum layer of 1.5 cm thickness, going
Preparation down 15 cm along the sides should be applied
Clean the surfaces and roughcast them (0.3 cm) for topping the foundations. After the surface is
without VEDACIT. dry, apply two coats of NEUTROL.
Place threaded pipes and tighten the flanges Neither smooth, nor flatten out with a steel float
inside and out. or mason's trowel.
All bricks up to the third course above the
foundation level should be laid with VEDACIT
waterproofing mortar.
Waterproof coatings should always be raised 60
cm above the soil or moisture stain level.
1:3 (cement: sand) mix and 2 kg of
VEDACIT/cement bag (50 kg).
Basements and underground areas
In poorly ventilated areas never use lime with
waterproof mortar.
Indoor walls
The mortar should dry at least once so VEDACIT
can perform its function.
Avoid quick coating drying.
The pipe end should standout from the internal Waterproof concrete
flange by about 3 cm. To obtain waterproof concrete mix, use with a
Waterproofing cement consumption over 300 kg/m³. An
indicated mix is 350 kg/m³ with a water/cement
1st day:..a) Cast it 1cm thickness on the wall and ratio up to 0.50.
half-round, and tighten it against the
wall. The water /cement ratio is reduced when CEMIX
is used, the water is repelled from the remaining
b) As soon as the mortar draws, make a capillary system with VEDACIT (% on the cement
roughcast with 1:3 mix without VEDACIT. weight).
c) Make a 1cm throw on the floor, squeeze and Consolidating and carefully curing in order to
pour sand in thin layers. obtain a waterproof concrete.
2nd day: Repeat the same operations.
3rd day: Repeat the same operations without
roughcast and without throwing sand. Float the
surfaces with a wooden float.
30
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 31
Storage Packaging
Stock the product at a covered, fresh, dry and • 1 kg jar
ventilated place, out of the reach of children • 3.6 kg bucket
and animals and away from sources of heat. • 18 kg bucket
• 200 kg drum
Attention
According to the weather conditions and the Personal protective equipment
shelf life, the product can show a more fluid • Safety glasses
consistency.
• PCV apron
Its quality, however, does not take any change.
The active content keeps the same, • Rubber gloves
independent from its visiosity.
The waterproof coatings do not accept thin
mass. It could be applied acrylic or PVA.
31
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 32
VEDACIT TAMP
Ultra fast crystallizer for stoppages.
32
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 33
VEDAJÁ
Waterproofing coating.
33
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 34
Packaging
• 4 kg bucket
• 18 kg bucket
• 18 kg box
34
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 17:00 Page 35
VEDAJÁ BRANCO
Waterproof coating against infiltrations and rain fall.
35
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 36
Attention
- To make waterproof slabs, marquises and
terraces use VEDAPREN.
- Apply preferably on the side where the water
posseses pressure.
- The treated walls may receive any type of
coating, except paint with a solvent base.
- Before performing occasional coating, the
treated surface should receive a rough layer
of BIANCO.
- Pools, water reservoirs and tanks may receive
water 3 to 5 days after the application of the
product taking into consideration
temperature, ventilation and relative humidity
of the place. The water reservoirs must be
washed and brushed before receiving water
so that its potability is not altered.
- In the case of application in pools, it is
essential to observe and correct occasional
cracks and flaws brought about by moving or
structural defficiency.
- If a former job of water proofing has been
done, is should be totally integrated and
sticked to the structure.
- Do not apply under intense sun.
Packaging
• 4 kg bucket
• 18 kg bucket
• 18 kg box
36
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 37
VEDAPREN
Waterproofing membrane for roofing and cold areas.
37
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 38
Roofing waterproofing
With the surface totally clean, execute the job in the following manner:
a) First coat of VEDAPREN (primer) diluted up to 15 % of water and applied by using a squeegee or
waxing brush directly to the subfloor.
b) On the following day, the operation is repeated but this time without diluting. In the same operation and
approximately half-meter back, apply VEDATEX cloth by unrolling and pressing it against VEDAPREN
by using a rubber squeegee.
c) VEDATEX cloth should be placed over the surface with the edges perfectly stuck down. Note to leave a
10 cm overlap.
38
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 39
39
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 40
40
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 41
VEDAPREN BRANCO
Membrane for waterproofing roofing.
41
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 42
VEDAPREN CONCRETO
Elastic and waterproof paint, acrylic base.
Characteristics Storing
Viscous liquid concrete colour Stock the product in a covered, fresh, dry and
First aid: item 4 page 210 ventilated place out of the reach of children
Density: 1.25 g/cm³ and animals and away from heat sources.
Basic composition: acrylic emulsion
Validity: 24 months Attention
It is recommended that objects are covered so
VEDAPREN CONCRETO is an acrylic paint, as to avoid damages by drops.
water base, specially developped for superficial
protection of concrete structures and masonry. Packaging
Creates a waterproof and elastic film, ideal for • 4.5 kg bucket
the application of external areas subject to rain • 18 kg bucket
downpour. Being concrete colour, it is ideal to • 200 kg drum
paint bridges and apparent cement buildings.
VEDAPREN CONCRETO does not need the use
of a sealer and renders good covering. It has Personal protective equipment
great sticking power and durability. • Safety glasses
• PVC apron
Fields of application • Rubber gloves
VEDAPREN CONCRETO is specially indicated
for:
• Masonry walls coated and external concrete
structures, subject to bad weather;
• Tiles and fibercement parts.
Way to use
Preparing the Substract
The surfaces should be porous and clean, dry
and free from dust.
Application
Apply 2 to 3 coats of VEDAPREN CONCRETO
with a roll, flat brush or painter’s brush, with an
intermission of 6 hours between them. The first
coat should be diluted in up to 10 % of water.
Approximate consumption
360 to 400 g/m²/coat
42
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 43
VEDAPREN PAREDE
Waterproofing paint against rainfall.
Characteristics Attention
Thick white liquid It is recommended that objects are covered so
First Aid: item 4, page 210 as to avoid damages by drops.
Density: 1.22 g/cm³
Basic Composition: acrylic emulsion
Packaging
Validity: 24 months • 3.6 kg bucket
• 18 kg bucket
• 18 kg can
VEDAPREN PAREDE is a waterproofing, elastic • 200 kg drum
and acrylic paint. It has high adherence and
durability.
VEDAPREN PAREDE avoids the arising of stains
Personal protective equipment
and mould, keeps the environment clean and • Safety glasses
healthy with a good appearance. • PVC apron
VEDAPREN PAREDE dispenses sealant • Rubber gloves
application. It can be let exposed as a final
finishing or receive an acrylic or latex paint.
Field of Application
VEDAPREN PAREDE is indicated for outside
walls exposed to rainfall.
Way to use
VEDAPREN PAREDE can be applied on plaster,
concrete, fiber cement and acrylic putty.
The surfaces should be porous, clean, dry and
free from dust.
Apply by using a roll or stock brush, in 2 to 3
coats.
Dilute the first coat up to 10% of water. Apply the
other coats with no dilution with a 6 hour interval
between them.
Approximate consumption
360 to 400 g/m²/coat
Storage
Stock the product at a covered, fresh, dry and
ventilated place, out of the reach of children
and animals and away from sources of heat.
43
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 44
VEDATOP
Waterproof coating, acrylic base, against infiltrations.
44
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 45
Packaging
• 4 kg bucket
• 18 kg bucket
• 18 kg box
45
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 46
VEDATOP FLEX
Flexible waterproof coating.
46
MT 2008 Inglês - 1a Parte.qxd 14/10/2008 15:27 Page 47
47
MT 2008 Inglês - 1a Parte.qxd 14/10/2008 15:27 Page 48
48
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 16:40 Page 49
ADIMENT
Superplasticizer for concrete.
Way to use
ADIMENT can be used in two ways:
1) reducing water for achieving high strength;
2) keeping the water quantity unchanged for
achieving high fluidity.
ADIMENT should be added to mixing water
immediately before pouring the concrete because
its effect decays in approximately 30 minutes.
The mixture should be mixed in a concrete mixer
for at least 5 minutes.
49
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 50
ADIMENT MC
High performance superplastfier.
Way to use
Add ADIMENT MC to the mixing water
immediately before the launch of the concrete,
as the effect of the product diminishes in
50
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 51
ADIMENT PREMIUM
Hiperplastifier for concrete.
Characteristics Attention
Amber liquid, free from chlorides It is recommended that preliminary tests be
First aid: item 4 page 210 carried out under the same conditions as the
Density: 1.09 g/cm³ brickwork to determine the ideal dosing of the
Basic composition: policarboxylate product and its compatibility with the cement
to be used.
Validity: 12 months
Fields of application
• Concrete of high performance.
• Concrete for pre-moulds.
• Concrete for special repairs.
Way to use
Firstly perform a pre-mixture of cement and
aggregates, adding approx. 70% of the water
volume to be used. Afterwards add ADIMENT
PREMIUM to the rest of the water.
Approximate consumption
0.3 to 1.0 % over the mass of cement
Storage
Stock the product at a covered, fresh, dry and
ventilated place, out of the reach of children
and animals and away from sources of heat.
51
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 52
Characteristics Storage
Amber liquid, free from chlorides Stock the product at a covered, fresh, dry and
First aid: item 4 page 210 ventilated place, out of the reach of children
Density: 1.08 g /cm³ and animals and away from sources of heat.
Basic composition: policarboxylate
Validity: 12 months Packaging
• 18 kg bucket
ADIMENT PREMIUM FAST is an hyperplastifier • 200 kg drum
admixture with the power to reduce water and
extraordinary fluidity. Attention
ADIMENT PREMIUM FAST enables the Ir is recommended that preliminary tests be
concretes with silica a significant reduction of carried out under the same conditions as the
permeability with great sticking power, brickwork to determine the ideal dosing of the
cohesion and free from segregation and product and its compatibility with the cement
exudation. to be used.
Apart from this, due to its low porousity, the
concrete made with ADIMENT PREMIUM FAST
shows great durability and resistance to
Personal protective equipment
aggresive atmospheres. Concrete correctly • Safety glasses
calculated with ADIMENT PREMIUM FAST • PVC gloves
eliminate the use of "vibrofinishing". • PVC apron
Fields of application
• Especially formulated for pre-moulded
concrete where one desires high resistance
in a short period of time.
Way to use
Application
In small concrete mixers, add to the concrete
70% of the water stipulated in the proportion of
ingredients for concrete and homogenize. Add
ADIMENT PREMIUM FAST into the total of
water of the concrete. For better efficiency in
concretes with a factor water/cement below
0.35, it is recommended that same be mixed
for at least 15 minutes.
Approximate consumption
0.3 to 1.5 % over the mass of cement
52
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 53
ADIMENT SUPER
Superplastifier for concrete.
Characteristics Storage
Brown colour liquid, free from chlorides Stock the product at a covered, fresh, dry and
First aid: item 4 page 210 ventilated place out of the reach of children
Density: 1.10 g/cm³ and animals and away from sources of heat.
Basic composition: sulfonated naftalene
Validity: 12 months Attention
It is recommended that preliminary tests be
ADIMENT SUPER is a superplastifying carried out under the same conditions as the
admixture with a high dispersion power. Allows brickwork to determine the ideal dosing of the
a series of advantages to the concrete, such product and its compatibility with the cement
as: to be used.
- initial and final high resistance;
- easyness to launch and condense; Packaging
- higher waterproofing; • 20 kg bucket
- excellent finishing; • 200 kg drum
ADIMENT SUPER renders the concrete high
resistance and/or high fluidity, allowing to Personal protective equipment
perform concreting at places of difficult access. • Safety glasses
• PVC apron
Fields of application • Rubber gloves
• Concretes of building structures, bridges,
tanks, pavements, etc.
• Pre-moulds;
• Concrete with microsilica;
• Pumped concrete.
Way to use
ADIMENT SUPER is employed basically to
diminish the use of water to obtain high
resistances, or to maintain the quantity of
water unchanged, in order to obtain high
fluidity.
Add ADIMENT SUPER to the mixing water
immediately before the launch of the concrete,
as its effect diminishes in approximately 30
minutes. Mix for 5 minutes in the concrete
mixer.
Approximate consumption
0.5 to 1.5% over the cement mass
53
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 54
ADIMENT SUPER MC
Concentrated superplastifier for concrete.
Characteristics Attention
Brown liquid, free from chlorides It is recommended that preliminary tests be
First aid: item 4 page 210 carried out under the same conditions as the
Density: 1.23 g/cm³ brickwork to determine the ideal dosing of the
Basic composition: sulfonated naftalene product and its compatibility with the cement
to be used.
Validity: 12 months
Fields of application
• Concretes of building structures, bridges,
tanks, pavements, etc;
• Pre-moulds;
• Concrete with microsilica;
• Pumped concrete.
Way to use
ADIMENT SUPER MC is employed basically to
diminish the use of water to obtain high
resistances or to maintain the quantity of water
unchanged, in order to obtain high fluidity.
Add ADIMENT SUPER MC to the mixing water
immediately before the launch of the concrete.
Mix for 5 minutes in the concrete mixer.
Approximate consumption
0.5 to 1.5% over the cement mass
Storage
Stock the product at a covered, fresh, dry and
ventilated place, out of the reach of children
and animals and away from sources of heat.
54
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 55
ADIMENT SUPER RD
Superplastifier and retarder for concrete.
Fields of application
• Concrete of building structures, bridges,
tanks, pavements, etc;
• Pre-moulds;
• Concrete with microsilica;
• Pumped concrete.
Way to use
ADIMENT SUPER RD is employed basically to
diminish the use of water to obtain high
resistances or to maintain the quantity of water
unchanged in order to obtain high fluidity.
Add ADIMENT SUPER RD to the mixing water
immediately before the launch of the concrete
as its effect diminishes in approximately 30
minutes. Mix for 5 minutes in the concrete
mixer.
55
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 56
CEMIX
Plasticizer / water reducer for concrete.
Way to use
CEMIX should be added to mixing water.
The quantity of water can be reduced as
compared to standard concrete. First, check the
desired workability.
Although thick when being poured from the
concrete mixer, the CEMIX added concrete is
easily consolidated, avoiding the occurrence of
segregation and "honeycombs".
56
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 57
CEMIX 2000
Poly-functional plasticizer admixture.
Characteristics Attention
Dark brown liquid Tests should always be performed under the
First Aid: item 4, page 210 same utilization conditions in order to determine
the products ideal proportion and its compatibility
Density: 1.19 g/cm³ with the cement to be used.
Basic Composition: naphtalene sulfonade
Validity: 6 months Packaging
• 20 kg bucket
CEMIX 2000 is a poly-functional plasticizing • 220 kg drum
admixture with high reducing water power.
It has simultaneous action of plasticizer Personal protective equipment
and superplasticizer without changing the setting
time. • Safety glasses
CEMIX 2000 allows concrete with great • PVC apron
workability and low water/cement ratio. So, it • Rubber gloves
obtains a concrete with great durability,
waterproofing and high resistance.
CEMIX 2000 can be used with a retarder
(RETARD or RETARD VZ) or an air-entraining
admixture (CEMIX-AIR) with previous tests.
Field of Application
• High performance concrete
• Pumped concrete.
• Apparent concrete.
• Waterproofing concrete.
Way to use
CEMIX 2000 should be added to mixing water,
always obeying the dosage studied in previous
tests.
The quantity of water can be reduced as
compared to standard concrete. First, check the
desired workability.
Approximate consumption
0.3 to 1.5% of CEMIX 2000 on the cement
weight.
Storage
Stock the product at a covered, fresh, dry and
ventilated place, out of the reach of children
and animals and away from sources of heat.
57
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 58
CEMIX 2026
Polifunctional admixture for concrete.
Characteristics Packaging
Brown liquid free from chlorides • 20 kg bucket
First aid: item 4 page 210 • 220 kg drum
Density: 1.14 g/cm³
Basic composition: sulfonated naphtalene Personal protective equipment
Validity: 6 months • Safety glasses
• PVC apron
CEMIX 2026 is a polifunctional admixture with • Rubber gloves
high water reduction power, with simultaneous
activity to plastify and superplastify. It allows
the obtention of waterproof concrete with
excellent working performance, high
resistances and low relation water/cement.
Fields of application
• High performance concrete;
• Pumped concrete;
• Apparent concrete;
• Waterproof concrete.
Approximate consumption
0.3 to 0.6 % over the cement mass.
Used in larger doses CEMIX 2026 has a
retarding performance.
Storage
Stock the product at a covered, fresh, dry and
ventilated place out of the reach of children
and animals and away from sources of heat.
Attention
It is recommended that preliminary tests be
carried out under the same conditions as the
brickwork to determine the ideal dosing of the
product and its compatibility with the cement
to be used.
58
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 59
CEMIX-AIR
Air-entraining for concrete and mortar.
Characteristics Attention
Light yellow liquid Tests should always de performed under the
First Aid: item 4, page 210 same utilization conditions in order to determine
the product ideal proportion and its compatibility
Density: 1.02 g/cm³ with the cement to be used.
Basic Composition: alkyl-aril-sulfonade
Validity: 6 months Packaging
• 18 kg bucket
CEMIX-AIR increases concrete workability, • 200 kg drum
especially for low cement consuming mixes and
fine granulation deficient. Personal protective equipment
CEMIX-AIR improves the properties of fresh • Safety glasses
concrete making it more cohesive, reducing
segregation and increasing water-tightness. It is • PVC apron
usually used in combination with a water • Rubber gloves
reducer/retarder (RETARD or RETARD VZ) for
maximum mechanical strength.
Field of Application
• Concrete in contact with seawater.
• Poor-fines concrete.
• Poor cement mix mortar.
Way to use
CEMIX-AIR is added to water. Also when using
water reducer (CEMIX), add them separately to
water.
Mix in the concrete mixer for approximately 5
minutes.
For the same water/cement ratio, the mechanical
strength decreases as the entrained air
increases.
Approximate consumption
CEMIX-AIR is used in the proportion of 0.04% to
0.12% on the cement weight, in accordance to
the desired air content.
Storage
Stock the product at a covered, fresh, dry and
ventilated place out of the reach of children
and animals and away from sources of heat.
59
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 60
FAZGRAUTH VEDACIT
Multidosing admixture to carry out micro-concrete and concrete at brickwork.
60
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 61
MAITI
Synthetic resin for concrete.
Field of Application
• Pre-fabricated concrete.
• Pre-mixed concrete.
• Mortar.
Way to use
For perfect performance, MAITI requires a
minimum 300 kg/m³ cement consumption.
The proportion is done in two stages. Firstly,
water should be added to achieve a
water/cement ratio near to 0.30. Then, MAITI is
added until achieving the required consistency.
Approximate consumption
3 to 10 kg MAITI/m³ of concrete
Storage
Stock the product at a covered, fresh, dry and
61
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 62
RETARD
Retarder/plasticizer for concrete.
Characteristics Storage
Dark liquid Stock the product at a covered, fresh, dry and
First Aid: item 4, page 210 ventilated place out of the reach of children
and animals and away from sources of heat
Density: 1.15 g/cm³
Basic Composition: carbohydrates Attention
Validity: 6 months
Tests should always be performed under the
same utilization conditions in order to determine
RETARD is an admixture that delays the the products ideal proportion and its compatibility
beginning of setting thus providing better with the cement to be used.
concrete pouring conditions.
RETARD is recommended for concrete mixed at Packaging
plants far from the pouring locations. • 20 kg bucket
RETARD improves the concrete workability and • 230 kg drum
distributes the hydration heat development over a
longer period of time, thus avoiding the
occurrence of cracking in large blocks.
Personal protective equipment
RETARD allows for interruptions in successive • Safety glasses
concrete pouring thus avoiding dry joints in • PVC apron
addition to improving concrete adherence to the • Rubber gloves
reinforcement frame.
RETARD makes it possible to reduce the water
mixture thus obtaining higher strengths.
Field of Application
RETARD is indicated for structural concrete in
mixing plants and large construction works:
• Concrete for dams.
• Pre-stressed and precast concrete.
• Pumped concrete.
Way to use
RETARD is added to the mixing water. It can be
used together with plasticizer (CEMIX) or air-
entraining products (CEMIX-AIR).
It allows for reducing the mixing water while
keeping the same workability.
Approximate consumption
0.2% to 0.3% of RETARD on the cement weight.
62
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 63
RETARD 100
Retarder/plastifier for concrete.
Characteristics Packaging
Dark liquid free from chlorides • 20 kg bucket
First aid: item 4 page 210 • 220 kg drum
Density: 1.10 g/cm³
Basic composition: carbohydrates Personal protective equipment
Validity: 6 months • Safety glasses
• PVC gloves
RETARD 100 retards the setting time process, • PVC apron
bringing about better concreting
conditions. RETARD 100 distributes the heat
development of hydration for a longer span of
time.
Allows interruptions in successive concreting
jobs avoiding cold joints.
Fields of application
• RETARD 100 is indicated for:
- structural concrete;
- concrete dam masses;
- apparent concrete and pre-moulds;
- pumped concrete.
Way to use
RETARD 100 is added to the mixing water.
Approximate consumption
0.3% over the mass of cement.
Storage
Stock the product at a covered, fresh, dry and
ventilated place out of the reach of children
and animals and away from sources of heat
Attention
It is recommended that preliminary tests be
carried out under the same conditions as the
brickwork to determine the ideal dosing of the
product and its compatibility with the cement
to be used.
63
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 64
RETARD CCR
Plastifying admixture for concrete compacted by a roll.
Characteristics Packaging
Dark liquid free from chlorides • 220 kg drum
First aid: item 4 page 210
Density: 1.10 g/cm³ Personal protective equipment
Basic composition: carbohydrates • Safety glasses
• PVC gloves
RETARD CCR is a plastifying admixture and • PVC apron
retarder, specially formulated for use in
concrete compacted by roll, with dry
consistency and having low cement
consumption. Reduces vibration time and loss
of workability as time goes by. Thus, allows an
expressive reduction in the mixing water, apart
from significant gain with maintenance and
workability.
Fields of application
RETARD CCR is specially designed for using
with cement compacted by a roll.
Way to use
RETARD CCR is added to the mixing water of
the concrete according to established dose in a
specific trial test (Cannon Time).
Approximate consumption
0.7 to 1.5 % over the cement mass.
Storage
Stock the product at a covered, fresh, dry and
ventilated place out of the reach of children
and animals and away from sources of heat
Attention
It is recommended that preliminary tests be
carried out under the same conditions as the
brickwork to determine the ideal dosing of the
product and its compatibility with the cement
to be used.
64
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 65
RETARD SP
Superficial retarder for concrete.
Characteristics Storage
Viscous liquid free from chlorides Stock the product at a covered, fresh, dry and
First aid: item 4 page 210 ventilated place out of the reach of children
Density: 1.12 g/cm³ and animals and away from sources of heat.
Basic composition: carbohydrates
Validity: 6 months Attention
It is recommended that preliminary tests be
RETARD SP retards the superficial hardening carried out under the same conditions as the
of the concrete allowing its removal between brickwork to determine the ideal dosing of the
24 to 48 hours after concreting. product and its compatibility with the cement
to be used.
Fields of application Packaging
• For surfaces where one desires the removal
of the superficial paste of the cement, • 20 kg bucket
obtaining thus the rugosity of the large • 200 kg drum
aggregate.
Personal protective equipment
Way to use • Safety glasses
• PVC apron
Application
• Rubber gloves
RETARD SP is applied over the models before
concreting. After the drying of the film (approx.
24 hours) one may start the concreting
process. Do not expose the treated models with
RETARD SP to rain or excessive sun. Wait
between 24 and 48 hours for demodeling and
wash the surfaces with water jets and brush.
Dilutions
- Large aggregate bigger than 2 cm: pure
RETARD SP
- Large aggregate between 1 and 2 cm: 1 part
of RETARD SP 1 part of water
- Large aggregate smaller than 1 cm: 1 part of
RETARD SP 2 parts of water
One may also dilute in water 1:1 and spray
over the fresh concrete, washing afterwards
the surface after 48 hours.
Approximate consumption
- Pure 300 g/m².
- Dilutions: 1:1 = 150 g/m².
1:2 = 100 g/m².
65
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 66
RETARD VZ
Retarder/plasticizer and densifier for concrete.
Characteristics Attention
Brown liquid Tests should always be performed under the
First Aid: item 4, page 210 same utilization conditions in order to determine
the products ideal proportion and its compatibility
Density: 1.17 g/cm³ with the cement to be used.
Basic Composition: carbohydrates
Validity: 6 months Packaging
• 20 kg bucket
RETARD VZ fulfills the necessities of delaying the • 200 kg drum
setting beginning in addition to meeting the
effects obtained with the employment of Personal protective equipment
plasticizers. It provides a plastic, cohesive and
workable mixture, thus obtaining a homogeneous • Safety glasses
concrete with greater water-tightness, higher • PVC apron
mechanical strengths, higher resistance to • Rubber gloves
wearing, better appearance, higher protection of
the reinforcement steel and longer durability.
RETARD VZ allows for a significant reduction in
the mixing water, thus providing considerable
increase in strength.
Field of Application
• Pre-mixed or mixed in place concrete.
• Special concrete.
• Re-vibrating concrete.
Way to use
RETARD VZ is added to the mixing water. It
allows reducing the mixing water while keeping
the same workability.
Approximate consumption
0.20% to 0.35% of RETARD VZ on the cement
weight.
Storage
Stock the product at a covered, fresh, dry and
ventilated place out of the reach of children
and animals and away from sources of heat
66
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 16:40 Page 67
VEDACIT RAPIDÍSSIMO
Ultra-quick setting waterproofing material.
67
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 68
Characteristics Attention
Colourless liquid, not alkaline, free from It is recommended that preliminary tests be
chlorides, pH 3 carried out under the same conditions as the
First aid: item 4 page 410 brickwork to determine the ideal dosing of the
Density: 1.30 g/cm³ product and its compatibility with the cement
Basic composition: sulfates to be used.
Validity: 12 months
Packaging
VEDACIT RAPIDÍSSIMO 100 is a non alkaline • 250 kg plastic drum
admixture, which accelerates the setting and
the hardening of the concrete bringing about Personal protective equipment
high initial and final resistances. Enables great • Safety glasses
adherence of the concrete layers projected to • Semifacial mask with chemical filter
the surfaces and low reflexion indexes.
• Boots
Fields of application • Long sleeve shirts
• Rubber gloves
• Concrete projected for:
- tunnels;
- arched roofs;
- slopes;
- channels;
- tanks;
- repairs and structure reinforcement.
Way to use
Preparing the Product
VEDACIT RAPIDÍSSIMO 100 is supplied ready
to be used .
Application
Dry sand should be used for a better
performance of the product.
Approximate consumption
VEDACIT RAPIDÍSSIMO 100 is dosed
according to the resistance and the setting
time desided: 3 to 12% over the cement mass.
Storage
Stock the product at a covered, fresh, dry and
ventilated place out of the reach of children
and animals and away from sources of heat.
68
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 69
Characteristics Attention
Greenish liquid, not alkaline, free from chlorides It is recommended that preliminary tests be
First aid: item 4 page 210 carried out under the same conditions as the
Density: 1.46 g/cm³ brickwork to determine the ideal dosing of the
Basic composition: sulfates product and its compatibility with the cement
to be used.
Validity: 12 months
Way to use
Preparing the Product
VEDACIT RAPIDÍSSIMO 150 is supplied ready
to be used.
Application
Dry sand should be used for a better
performance of the product.
Approximate consumption
VEDACIT RAPIDÍSSIMO 150 is dosed
according to the resistance and the setting
time desided: 3 to 12% over the cement mass.
Storage
Stock the product at a covered, fresh, dry and
ventilated place out of the reach of children
and animals and away from sources of heat.
69
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 70
Characteristics Storage
Orange type colour, free from chlorides, pH 14 Stock the product at a covered, fresh, dry and
First aid: item 3 page 209 ventilated place out of the reach of children
Density: 1.50 g/cm³ and animals and away from sources of heat.
Basic composition: aluminates
Validity: 3 months Attention
It is recommended that preliminary tests be
VEDACIT RAPIDÍSSIMO 200 is designed for carried out under the same conditions as the
projected concrete, providing: brickwork to determine the ideal dosing of the
product and its compatibility with the cement
- great acceleration, in setting time and to be used.
hardening;
- excellent adherence even to humid surfaces,
implying in a low reflection index; Packaging
- increase in productivity; • Bulk
- precision in admixture dosing; • 20 kg bucket
- carry out of more dense layers. • 250 kg drum
VEDACIT RAPIDÍSSIMO 200 shows an alkaline
pH, compatible with the cement. Personal protective equipment
• Safety glasses
Fields of application • PVC gloves
• VEDACIT RAPIDÍSSIMO 200 is designed for • PVC apron
coating: • Semifacial mask with chemical filter
- tunnels; • Boots
- channels;
- adducer;
- basement;
- slopes;
- retaining walls;
- structural reinforcement, etc.
Way to use
Preparing the Product
VEDACIT RAPIDÍSSIMO 200 is ready to be
used.
Application
Dry sand should be used for a better
performance of the product.
Approximate consumption
3.5 to 6% over the cement mass.
70
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 16:40 Page 71
VEDACIT RAPIDÍSSIMO EM PÓ
Ultra-quick setting waterproofing material for shot concrete and mortar.
Characteristics Packaging
White powder • 25 kg bag
First Aid: item 3, page 209
Basic Composition: aluminates Personal protective equipment
Validity: 6 months • Safety glasses
• PVC apron
• Boots
VEDACIT RAPIDÍSSIMO EM PÓ (powder form) • Rubber gloves
provides:
• Semifacial mask with chemical filter against
• fast hardening of Portland cement; dust
• impermeability to liquids;
• optimal adherence.
The ultra-quick setting allows the formation of
thicker layers.
Field of Application
• Shot concrete for coating tunnels, domes,
slopes, reservoirs and channels.
• Structural recovery and reinforcement.
Way to use
Concrete must be prepared in accordance to the
desired mixes and applied with suitable
equipment.
Approximate consumption
3% to 5% of VEDACIT RAPIDÍSSIMO EM PÓ on
the cement weight. Mix dry.
For works in the presence of moisture, increase
the dosage. It should be done previous testing to
verify the resistance to be obtained.
Storage
Stock the product at a perfectly dry and
ventilated place, following the same principles
of storing cement.
Attention
Performing previous testing is always required in
order to establish the ideal admixture proportion
and its compatibility to the cement to be used.
71
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 72
VEDACIT RÁPIDO CL
Setting and hardening accelerator for concrete and mortar.
Without
Rate: VEDACIT
VEDACIT 1:3 1:6 1:9 1 : 12 1 : 15 1 : 18
RÁPIDO CL / Water
RÁPIDO CL
Consumption:
VEDACIT RÁPIDO -- 61 kg 34 kg 24 kg 19 kg 15 kg 12 kg
CL / m³ concrete
Ages Compressive strength (MPa)
72
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 73
Attention
• This is a calcium chloride product.
• Performing previous testing is always required
in order to establish the ideal admixture
proportion and its compatibility to the cement
to be used.
Packaging
• 1.4 kg jar
• 3.6 kg bucket
• 20 kg bucket
• 250 kg drum
73
MT 2008 Inglês - 1a Parte.qxd 14/10/2008 15:27 Page 74
74
MT 2008 Inglês - 1a Parte.qxd 14/10/2008 15:27 Page 75
75
MT 2008 Inglês - 1a Parte.qxd 14/10/2008 15:27 Page 76
76
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 77
ALVENARIT
Plasticizer admixture for laying and casting mortar.
Characteristics Attention
Dark liquid • It is advisable to always perform tests under
First Aid: item 4, page 210 the same utilization conditions in order to
determine the ideal admixture proportion.
Density: 1.01 g/cm³
• Excessively fine sand, that demands a high
Basic Composition: natural resins water consumption, may cause the mortar to
Validity: 24 months weaken.
Recommended Mixes
Application
Mix (Cement: sand)
Laying and indoors coating...................up to 1:8
Outdoors coating..................................up to 1:6
77
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 16:40 Page 78
CONCENTRADO OBE
Powder admixture for laying mortar.
Characteristics Storage
Powder Stock the product at a perfectly dry and
First Aid: item 4, page 210 ventilated place, following the same principles
of storing cement.
Basic Composition: mineral fillers
Validity: 12 months Packaging
• 14 kg bucket
CONCENTRADO OBE modifies the physical
mortar characteristics, making them plastics,
more workable and with high adherence.
Personal protective equipment
• Safety glasses
CONCENTRADO OBE slightly delays the setting
start and significantly improves the mechanical • PVC apron
strength development. • Mask with filter against dust
CONCENTRADO OBE allows the ordinary mortar • Rubber gloves
utilization for laying, employing only 2 to 3 mm of
mortar.
Field of Application
• Especially indicated for preparing mortar for
laying blocks, glazed tiles, ceramics, pastilles,
etc
Way to use
The surface should be dry, clean and floated.
Dry mix, during 3 minutes in a concrete mixer:
- 1 part of Portland cement;
- 3 parts of dry medium sand;
- 2% of CONCENTRADO OBE on the cement
weight.
Note: other mixes may be utilized depending on
the works condition.
After mixing, add water in enough quantity to
make the mortar plastic and workable.
Lay the mortar in a uniform layer by utilizing a
toothed float.
Apply glazed or ceramic tiles dry and caulking
them no sooner than 24 hours.
Approximate consumption
1 kg CONCENTRADO OBE/cement bag (50 kg).
78
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 79
EXPANSOR
Expanding admixture for wedging mortar.
Characteristics Storage
White powder Stock the product at a covered, fresh, dry and
First Aid: item 4, page 210 ventilated place out of the reach of children
and animals and away from sources of heat.
Basic Composition: mineral filler
Validity: 9 months Attention
Performing previous tests is always necessary for
EXPANSOR provides mortar with: establishing the ideal admixture proportion and
- reduction in the quantity of the mixing water; its compatibility with the cement to be used.
- greater plasticity making the application to
notches and cavities easier; Packaging
- shrinkage compensation due to the moderate • 1 kg jar
expansion effect, although not exercising • 3 kg bucket
pressure to the structure; • 16 kg bucket
- effective filling of all voids. • 25 kg bag
Field of Application Personal protective equipment
• Wedging in general. • Safety glasses
Way to use • PVC apron
• Mask with filter against dust
Add EXPANSOR to the cement dry. Use the • Rubber gloves
minimum quantity of water as far as possible
due to greater plasticity.
Use 1 part of Portland cement to 3 parts of
medium sand and 1% of EXPANSOR on the
cement weight.
The surface should be just a little wet.
For a better product performance, the mortar
should have a dry consistency and should be
utilized until 40 minutes (25°C) after water
addition.
Let an opening of 3 cm between the masonry
and the structure.
Stamp well the mortar inside the opening for a
perfect filling of the voids.
Approximate consumption
EXPANSOR is used in the proportion of 1% on
the cement weight.
500 g EXPANSOR/50 kg cement.
79
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 80
MIX-OIL
Lubricating admixture for blocks and precast pieces.
Characteristics Attention
Yellowish liquid Performing previous testing is always required in
First Aid: item 4, page 210 order to establish the ideal admixture proportion
and its compatibility to the cement to be used.
Density: 1.02 g/cm³
Basic Composition: alkyl-aril-sulfonade
Validity: 12 months
Packaging
• 3.6 liter bucket
• 18 liter bucket
MIX-OIL incorporates minuscule uniformly • 200 liter drum
distributed air bubbles to concrete and mortar
thus significantly improving their characteristics: Personal protective equipment
- by accelerating the initial strength, reducing the
time for formwork removal and transportation • Safety glasses
of pieces; • PVC apron
- by making finishing of faces and sharp corners • Rubber gloves
easier;
- by reducing segregation and fissuring;
- by increasing the putty workability.
Field of Application
MIX-OIL is especially indicated for low cement
consumption pieces and very dry mixtures:
• blocks;
• gutters;
• curbs;
• precast pieces.
Way to use
MIX-OIL should be added to water for a better
mixing of the product in the mortar.
Approximate consumption
20 ml MIX-OIL per each cement bag (50 kg).
Storage
Stock the product at a covered, fresh, dry and
ventilated place out of the reach of children
and animals and away from sources of heat.
80
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 81
TRICOSAL
Fluidifier for injections in cracks and sheaths.
Way to use
TRICOSAL is added 2 1/2 minutes after
beginning to mix water to cement.
Agitation should total 4 minutes before starting
injection.
The mixture should remain under slow agitation
until the end of pumping.
Tests shall always be performed under the same
utilization conditions in order to determine the
product ideal proportion.
81
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 82
VEDALIT
Concentrated plastifying admixture for foundation mortar and rough cast.
Characteristics Storage
Dark liquid free from chlorides Stock the product at a covered, fresh, dry and
First aid: item 4 page 210 ventilated place, out of the reach of children
Density: 1.01 g/cm³ and animals and away from sources of heat.
Basic composition: natural resins
Validity: 24 months Attention
- It is recommended that preliminary tests be
VEDALIT is a concentrated admixture which carried out under the same conditions as the
provides excellent binding and working brickwork to determine the ideal dosing of
performance to mortars and rough casts. Being the product and its compatibility with the
liquid VEDALIT easens the job, guaranteeing cement to be used.
material saving, speed in accomplishment and - Use medium sand and preferably cement type
excellent conclusion of the job. It adds a series II or V. Rough and excessively fine sand and
of advantages to the mortars: better adherence, cement with high content of additives may
cohesion and waterproofness, absence of bring about the loss of resistance and crack
cracks and less exuding. Mortars prepared with of the mortar.
VEDALIT don’t have to be hardened. Being free - VEDALIT is also supplied in powder (VEDALIT
from lime, mortars prepared with VEDALIT do EM PÓ)
not detach, even when applied in cellars and at
other places of low ventilation, thus enabling
the possibility of receiving waterproof paint.
Packaging
• 100 g small bag (Vedalit NE)
Fields of application • 1 kg bucket
• 1 kg flask with doser
• Foundation mortar and rough cast. • 3.6 kg bucket
Way to use • 18 kg bucket
• 200 kg drum
Preparing the Product
Dilute VEDALIT in the mixing water, according Personal protective equipment
to indicated dosage. • Safety glasses
• PVC apron
Application
• Rubber gloves
Perform the mixing of mortar, preferably in a
concrete mixer, using for this purpose always
clean medium sand.
Recommended proportions
Cement:sand
Foundation ....................................... up to 1:8
Internal and external coating ............. up to 1:6
Approximate consumption
100 ml/bag of cement (50 kg).
82
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 16:40 Page 83
VEDALIT EM PÓ
Powder plastifying admixture for mortars.
Characteristics Attention
White powder - It is recommended that preliminary tests be
First aid: item 4 page 210 carried out under the same conditions as the
Basic composition: tensoactive brickwork to determine the ideal dosing of
Validity: 24 months the product and its compatibility with the
cement to be used.
- Use medium sand and preferably cement type
VEDALIT EM PÓ provides excellent binding and II or V. Rough and excessively fine sand and
working performance to mortars and rough cement with high content of additives may
casts. It addes a series of advantages to bring about the loss of resistance and crack
mortars: better adherence, cohesion and of the mortar.
waterproofness absence of cracks and less
exuding. Mortars prepared with VEDALIT EM
PÓ don’t have to be hardened. Being free from Packaging
lime, mortars prepared with VEDALIT EM PÓ • 17 kg bucket
do not detach, even when applied in cellars • 25 kg bag
and at other places of low ventilation, thus
enabling the possibility of receiving waterproof
paint.
Personal protective equipment
• Safety glasses
Fields of application • PVC apron
• Mask with filter against dust
• Foundation mortar and rough cast, prepared
at the brickwork or pre-fabricated. • Rubber gloves
Way to use
Preparing the Product
VEDALIT EM PÓ should be pre-mixed in a
concrete mixer to the cement and sand. Use
always medium sand, clean and free from
organic material.
Approximate consumption
0.1 to 0.2% over the cement mass.
Storage
Stock the product at a covered, fresh, dry and
ventilated place, out of the reach of children
and animals and away from sources of heat.
83
MT 2008 Inglês - 1a Parte.qxd 14/10/2008 15:27 Page 84
84
MT 2008 Inglês - 1a Parte.qxd 14/10/2008 15:27 Page 85
ARGAMASSA ESTRUTURAL 240: dry high strength mortar for coatings ...............................................87
ARGAMASSA ESTRUTURAL 250: polymer modified mortar for coatings and repairs............................88
ARGAMASSA OBE 500: mortar for restoring...........................................................................................89
ARGAMASSA OBE EXTERIOR AC-II: mortar to put in place tiles and ceramics at outside places ..........90
ARGAMASSA OBE INTERIOR AC-I: mortar to put in place tiles and ceramics at inside places..............91
GRAUTH SG: mortar for work with micro-concrete.................................................................................92
V-1 GRAUTH: high strength mortar for grouting ......................................................................................93
V-1 GRAUTH S: self compacting mortar for micro-concreting ................................................................94
V-1 GRAUTH TIX: high resistance dry mortar ..........................................................................................95
V-2 GRAUTH: high strength expansive mortar for grouting......................................................................96
85
MT 2008 Inglês - 1a Parte.qxd 14/10/2008 15:27 Page 86
86
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 87
Characteristics Storage
Gray colour Stock the product at a perfectly dry and
First Aid: item 4, page 210 ventilated place, following the same principles of
storing cement.
Basic Composition: cement and additives
Validity: 6 months Packaging
• 40 kg bag
ARGAMASSA ESTRUTURAL 240 is a mortar for
coatings that presents high strength and great
adherence. It is waterproof and non-shrinkage Personal protective equipment
and does not present fissures. • Safety glasses
• PVC gloves
Field of Application • PVC apron
• Coatings and repairs to concrete structures and • Mask with filter against dust
base plates leveling for machinery and steel
structures.
• ARGAMASSA ESTRUTURAL 240 is indicated
for thickness ranging from 3 to 7 cm. For
greater thickness, ARGAMASSA ESTRUTURAL
250 is recommended.
Way to use
The surface must be clean, free of cement grout
and loose particles.
Previously wet the substratum, however without
soaking it.
Add water to ARGAMASSA ESTRUTURAL 240
and mix for 4 minutes, preferably in a concrete
mixer until obtaining the desired consistence that
should be very dry.
The dry-consistent utilized product (dry-pack
type) can be applied with a mason's trowel or
even with the hands, provided that gloves are
used. Float finish.
In locations subjected to intensive heat,
performing wet or chemical curing is suggested
by utilizing CURING. If the structure further
receives coating or paint, employ TRI-CURING.
Approximate consumption
22 kg/m²/cm of thickness.
87
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 16:40 Page 88
Field of Application
• Thin coatings and repairs to concrete and
masonry structures.
• Structural recovering.
Way to use
The surfaces must be perfectly clean, free of
cement grout and loose particles. Very dry
substratum should be dampened slightly.
Mix the ARGAMASSA ESTRUTURAL 250 powder
and liquid (A+B) components for 4 minutes,
preferably in a concrete mixer. Use the mortar
within a period not exceeding one hour.
Apply a layer of up to 1.0 cm with a mason's
trowel. Screed and finish with metal float.
Perform wet or curing agent by using TRI-
CURING.
88
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 89
89
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 90
91
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 92
GRAUTH SG
Mortar for work with micro-concrete.
92
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 93
V-1 GRAUTH
High strength mortar for grouting.
93
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 94
V-1 GRAUTH S
Self compacting mortar for micro-concreting.
94
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 95
V-2 GRAUTH
High strength expansive mortar for grouting.
Way to use
The contacting surfaces must be clean, free of
dust, cement, oils and paint.
Wet the surfaces before pouring but do not let
water dam up.
In accordance to the desired consistence, add
2.3 to 3.8 liter of clean water per V-2 GRAUTH
bag (25 kg). The mixture shall be made in a
concrete mixer for 6 minutes.
First, add 2/3 parts of water, intensively mixing
for 3 minutes. Then add the rest of the water.
For thickness over 5 cm, up to 30% - in weight -
of grit (washed, dry and dust-free) - 3 to 7 mm -
can be added without significant strength loss.
However, adding a maximum of 3 liter of water
per V-2 GRAUTH bag (25 kg) requires previous
testing.
96
MT 2008 Inglês - 1a Parte.qxd 14/10/2008 15:27 Page 97
97
MT 2008 Inglês - 1a Parte.qxd 14/10/2008 15:27 Page 98
98
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 99
CURING
Curing agent for concrete.
Characteristics Attention
White viscous liquid If the structure is to receive a coating or paint, as
First Aid: item 4, page 210 well as for floors and lanes, TRI-CURING should
be utilized.
Density: 1.00 g/cm³
Basic Composition: paraffinic hydrocarbon
emulsion Packaging
Validity: 12 months • 18 kg bucket
• 200 kg drum
CURING forms a waterproof film over fresh
concrete so protecting against the effects of
Personal protctive equipment
dehydration caused by heat and wind. • Safety glasses
It provides an uninterrupted curing process so • PVC apron
avoiding formation of fissures and helping on • Rubber gloves
developing mechanical strengths.
CURING dismisses the traditional methods of
keeping the concrete wet.
Field of Application
• Recently poured concrete structures.
• Precast elements.
Way to use
Mix CURING before use.
Apply by using a broad brush or low pressure
sprayer as soon as the concrete "draws" (matte
appearance). Apply evenly over the entire surface
just enough to make it evenly whitish.
Wash the sprayer as soon as the job is finished.
Approximate consumption
1 kg CURING / 5 to 6 m²
Storage
Stock the product at a covered, fresh, dry and
ventilated place, out of the reach of children
and animals and away from sources of heat.
99
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 100
CURING PAV
Curing agent for concrete pavements.
Characteristics Storage
White viscous liquid Stock the product at covered, fresh, dry and
First aid: item 4 page 210 ventilated places out of the reach of children
Density: 0.94 g/cm³ and animals and away from sources of heat.
Basic composition: paraffinic hydrocarbons
emulsion. Packaging
Validity: 12 months • 18 kg bucket
• 180 kg drum
CURING PAV protects the concrete against the
effects of dehydration brought about by heat Personal protective equipment
and wind. Avoids the building up of cracks and • Safety glasses
favours the progress of mechanical resistance.
• PVC apron
CURING PAV dispenses traditional methods
such as maintaining the concrete humid for • Rubber gloves
several days, being specially indicated for great
areas such as highways and industries.
CURING PAV abides to the demands of the
ASTM C 309 norms.
Fields of application
• Concrete pavements on:
- highways;
- industries;
- parking lots.
Way to use
Preparing the Product
Mix CURING PAV before using.
Application
With a low pressure sprayer, immediately after
the concrete acquired an opaque aspect, apply
CURING PAV equally, over all the surface, only
the amount needed to leave it uniformly
whitish. Wash the sprayer immediately after
usage.
Approximate consumption
1 kg CURING PAV/5 to 6 m².
100
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 101
TRI-CURING
Curing agent for concrete pavements.
Characteristics Packaging
White liquid • 18 kg bucket
First Aid: item 4, page 210 • 200 kg drum
Density: 1.02 g/cm³
Basic Composition: synthetic resin Personal protctive equipment
Validity: 12 months • Safety glasses
• PVC apron
TRI-CURING is a synthetic resin supplied ready • Rubber gloves
to use and aimed at being sprayed over the
recently poured concrete surface to provide
proper curing.
It prevents formation of fissures and helps in
developing perfect mechanical strength.
TRI-CURING does not form a film over the
surfaces so it can receive coating.
Field of Application
Pavements, roadways, airport lanes and all
surfaces which will later be painted or receive a
coating.
Way to use
TRI-CURING is supplied ready for use.
Apply over fresh concrete by using a low-
pressure sprayer as soon as the concrete
"draws" (matte appearance).
It is applied all at once over the entire surface
and just enough to make it whitish.
If the surface is to be intended to receive coating,
previous brushing is recommended until
elimination of possible product residues.
Approximate consumption
1 kg /5 m²
Storage
Stock the product at a covered, fresh, dry and
ventilated place, out of the reach of children
and animals and away from sources of heat.
101
MT 2008 Inglês - 1a Parte.qxd 14/10/2008 15:27 Page 102
102
MT 2008 Inglês - 1a Parte.qxd 14/10/2008 15:27 Page 103
CERA DESMOLDANTE OTTO: for precast concrete tracks and metal formwork...................................105
DESMOL: form removal agent for apparent concrete ............................................................................106
DESMOL BETONEIRA: form removal agent for metal surfaces .............................................................107
DESMOL CD: form removal agent for concrete .....................................................................................108
DESMOL RD: superficial demoulding retarder for concrete...................................................................109
103
MT 2008 Inglês - 1a Parte.qxd 14/10/2008 15:27 Page 104
104
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 105
Characteristics Attention
Yellow paste Before coating, check if the surface is free from
First Aid: item 3, page 209 dust or oil. The surface should be prepared in
accordance to NBR 7200 (ABNT)
Density: 0.86 g/cm³ recommendations. Extremely smooth surfaces
Basic Composition: paraffinic hydrocarbon should be picked.
Validity: 12 months
Packaging
CERA DESMOLDANTE OTTO forms an oily film • 14 kg bucket
between the concrete and formwork thus • 160 kg drum
preventing adherence of both.
It provides optimal appearance of precast pieces Personal protective equipment
and makes it possible to obtain even and fault- • Safety glasses
free surfaces. Therefore, it is also ideal for
applying to apparent concrete formwork. • Semifacial mask with appropriate filter for
organic vapour
CERA DESMOLDANTE OTTO does not stain
concrete. It makes the formwork removal easier • PVC gloves
and avoids the work of formwork cleaning. • PVC apron
Field of Application
• CERA DESMOLDANTE OTTO is especially
indicated for concrete formwork utilized in
precast tracks.
• It is also recommended for any types of metal
formwork.
Way to use
CERA DESMOLDANTE OTTO is supplied ready
for use. Spread it with a cloth or cotton waste
suffices.
Concrete can be poured right after applying the
product.
If the surface is to be coated, it is recommended
that it is brushed and roughcast made with
BIANCO be applied.
Approximate consumption
50 to 80 g/m² depending on the surface porosity.
Storage
Stock the product at a covered, fresh, dry and
ventilated place, out of the reach of children
and animals and away from sources of heat.
105
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 106
DESMOL
Form removal agent for apparent concrete.
Way to use
Mix before using.
DESMOL is water soluble in variable proportions
in accordance to the formwork condition.
DESMOL is added to water by slowly mixing.
Once it is prepared, it can be used for a long
time.
Rough cut lumber:1 part DESMOL: 5 parts of water
Plywood:1 part DESMOL: 10 parts of water
Molds immersion:1 part DESMOL: 12 parts of water
After dissolving, apply DESMOL evenly over the
formwork by using a stock brush or waxing
brush. After drying for one hour, concrete pouring
can be started. Clean and paint the formwork
with DESMOL prior to each use.
106
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 16:40 Page 107
DESMOL BETONEIRA
Form removal agent for metal surfaces.
Characteristics Storage
Dark brown oil Stock the product at a covered, fresh, dry and
First Aid: item 3, page 209 ventilated place, out of the reach of children
and animals and away from sources of heat.
Density: 0.85 g/cm³
Basic Composition: mineral oil
Validity: 24 months
Attention
Before coating, check if the surface is free from
dust or oil. The surface should be prepared in
DESMOL BETONEIRA presents strong adherence accordance to NBR 7200 (ABNT)
to metals. It is neither removed nor leached by recommendations. Extremely smooth surfaces
concrete. should be picked.
It enables an even and fault-free surface to be
obtained. Packaging
DESMOL BETONEIRA prevents concrete
adherence to steel plates thus making it easier to • 20 liter bucket
clean them at the end of each day work. The • 200 liter drum
concrete remainders are removed by a simple
water jetting. Personal protective equipement
It does not stain concrete. • Safety glasses
• Semifacial mask with appropriate filter for
Field of Application organic vapour
• Metal formwork. • PVC gloves
• Protection and conservation of concrete mixer • PVC apron
trucks.
• Concrete mixers in concrete central mixing
plants.
Way to use
Remove all foreign substances from the metal
surface and let it dry.
DESMOL BETONEIRA is applied plain by using a
broad brush or cotton waste in a thin layer to
obtain a thin film.
Wait for approximately two hours before starting
the formwork or protected equipment.
Reapply the product before each concrete
pouring.
Approximate consumption
125 m²/liter
107
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 108
DESMOL CD
Form removal agent for concrete.
Characteristics Storage
Yellowish liquid Stock the product at a covered, fresh, dry and
First Aid: item 4, page 210 ventilated place, out of the reach of children
and animals and away from sources of heat.
Density: 1.00 g/cm³
Basic Composition: fatty acids emulsion
Validity: 24 months
Attention
Before coating, check if the surface is free from
dust or oil. The surface should be prepared in
DESMOL CD forms a thin low viscosity layer accordance to NBR 7200 (ABNT)
between the concrete and formwork. It prevents recommendations.
the adherence between them and makes the
formwork removal easier without damaging the
concrete surfaces and edges.
Packaging
DESMOL CD keeps the concrete surface rough • 3.6 liter bucket
thus facilitating coatings adherence. • 18 liter bucket
It avoids the work of cleaning while conserving • 200 liter drum
the wood thus allowing for extensive formwork
reusing. Personal protective equipement
DESMOL CD does not stain concrete. It is neither • Safety glasses
flammable nor harsh to the skin. • PVC gloves
Field of Application • PVC apron
Way to use
Mix before using.
DESMOL CD is water soluble in a ratio of 1:8 to
1:10 proportioning in according to the formwork
condition. Add it slowly to water mixing until a
milky liquid is obtained.
After dissolving, apply DESMOL CD evenly over
the forms by using a stock brush or waxing
brush. After drying for one hour, concrete pouring
can begin. Always clean and paint the formwork
with DESMOL CD prior to each reuse.
Approximate consumption
100 to 200 m²/liter
108
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 109
DESMOL RD
Superficial demoulding retarder for concrete.
110
MT 2008 Inglês - 1a Parte.qxd 14/10/2008 15:27 Page 111
111
MT 2008 Inglês - 1a Parte.qxd 14/10/2008 15:27 Page 112
112
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 113
BIANCO
Adhesive for mortar and roughcasts.
113
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 114
Attention
• Very smooth surfaces due to utilization of
plasticized or resin formwork or formwork
containing excess of formwork releasing
agents, must be washed, brushed or even
picked in order to assure the roughcast perfect
adherence.
• Never use it pure, in paint form.
• In mortar for roughcasts, do not use slow
setting time cement.
Packaging
• 1 kg jar
• 3.6 kg bucket
• 18 kg bucket
• 200 kg drum
114
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 115
BRANCOL A
White glue for glazed tiles.
Characteristics Storage
White colour plastic putty Stock the product at a covered, fresh, dry and
First Aid: item 4, page 210 ventilated place, out of the reach of children
and animals and away from sources of heat.
Density: 1.64 g/cm³
Basic Composition: vinyl resin
Validity: 12 months
Packaging
• 700 g flask
• 5.5 kg bucket
BRANCOL A forms an elastic layer and highly
adherence between tile and wall. Quick Personal protective equipment
hardening, keeping enough elasticity not to
detach as a result of little movements. • Safety glasses
BRANCOL A facilitates tile laying. • PVC apron
• Rubber gloves
Field of Application
• All areas where tile gluing are intended, except
for swimming pools and shower cubicles.
Way to use
BRANCOL A is supplied ready for use. Always
keep packaging closed thus preventing the glue
hardening.
Do not wet the tiles before gluing.
Surfaces should be floated, cleaned and dust
free.
Application is made with a toothed float or by
spot gluing. The glue is applied with a toothed
float in flutings and the area of application should
always be less than 1 m².
Place the tiles in position and press them firmly.
Excess glue is removed with a wet cloth before
hardening.
For gluing small areas use the spot system: put
some BRANCOL A at the tiles four corners and
center. Firmly press the tile in position.
Approximate consumption
1.3 kg/m²
115
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 16:40 Page 116
COMPOUND ADESIVO
Epoxy structural adhesive.
Characteristics Notes
• When an adhesive, which does not run off, is
Two components required even when applied to vertical
First Aid: surfaces, the utilization of COMPOUND
A: item 3, page 209 ADESIVO TIX is indicated.
B: item 3, page 209 • For urgent requests or for wet but not soaked
Density: surfaces, COMPOUND ADESIVO 200 is
Components A+B: 1.52 g/cm³ indicated.
Basic Composition: • When it is necessary a low viscosity adhesive,
A: epoxy resin use COMPOUND ADESIVO GEL.
B: polyamine-amide
Validity: 12 months Approximate consumption
1.5 kg/m² /mm thickness
COMPOUND ADESIVO has excellent performing
for gluing the most different materials employed Storage
in civil construction. Stock the product at a covered, fresh, dry and
COMPOUND ADESIVO has optimal resistance to ventilated place, out of the reach of children
water, oils, greases and aggressive substances. and animals and away from sources of heat.
Its fluidity gives a higher yield and easiness to
apply that allows application in areas of difficult Packaging
access. • 2 cans totaling 1 kg (A+B)
Field of Application Personal protective equipment
• Gluing: • Safety glasses
- concrete - concrete;
- fresh concrete - hardened concrete; • PVC gloves
- concrete - iron - wood - glazed tile - ceramic • PVC apron
- stones - cement asbestos. • Semifacial mask with appropriate filter for
• Re-laying tiles in swimming pools. organic vapour
• Boat repairs.
Way to use
The surfaces should be clean, free from dust,
loose parts, greases, oils, etc.
Add the content of component B to component A
and thoroughly mix preferably using a
mechanical mixer. The product should be used
no later than 1 hour (at 25°C) after mixing.
Application should be done with a paint brush,
broad brush or putty knife by filling all cavities.
COMPOUND ADESIVO presents initial strength in
24 hours and maximum strength on the 7th day.
Clean the tools with SOLVENTE EPOXY
immediately after using them.
116
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 117
Characteristics Application
COMPOUND ADESIVO 200 is applied in a fine
Component A: white colour layer with a brush or spatula. Use the product
Component B: black colour in 40 minutes at most (25°C) after mixing is
First aid: performed. Clean the tools immediately after
Component A: item 3 page 209 usage with SOLVENTE EPOXY. Wash hands
Component B: item 3 page 209 with water and soap.
Density:
Component A+B: 1.69 g/cm³ Approximate consumption
Basic composition: 1,7 kg/m²/mm thickness
Component A: epoxy resin
Component B: polyamine Storage
Validity: 12 months Stock the product at a covered, fresh, dry and
ventilated place, out of the reach of children
COMPOUND ADESIVO 200 is an adhesive and animals and away from sources of heat.
which maintains its characteristics of high
adherence and mechanical resistance, even Storage
when applied on humid but not soaked Stock the product at a covered, fresh, dry and
surfaces. ventilated place out of the reach of children
COMPOUND ADESIVO 200 presents excellent and animals and away from sources of heat.
performance gluing different materials
employed at civil construction such as (iron,
concrete, wood, ceramics, stone, etc.) Attention
- When needed, considering an adhesive which
Fields of application does not flow, the use of COMPOUND
ADESIVO TIX is indicated.
• Gluing concrete - concrete, concrete-iron, - When an adhesive of high flowing is needed,
concrete-wood, etc. use COMPOUND ADESIVO GEL.
• Fasten machines and equipment.
• Structural recovery. Packaging
• Gluing pre-moulded structures.
• 1 kg (A+B) can
• Fixing with lead.
117
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 118
Characteristics Application
Apply the product by means of a flat wall
Component A: high fluidity, gray colour brush, roll or pour it to the place to be filled,
Component B: liquid within maximum 30 minutes after the mix has
First aid: been made.
Component A: item 3 page 209 COMPOUND ADESIVO GEL shows final cure in
Component B: item 3 page 209 7 days. Clean the tools with SOLVENTE EPOXY
Density: immediately after usage.Wash hands with
Component A+B: 1.50 g/cm³ water and soap.
Basic composition:
Component A: epoxy resin Approximate consumption
Component B: polyamine 1.5 kg/m²/mm thickness
Validity: 12 months
Storage
COMPOUND ADESIVO GEL is an epoxy base Stock the product at a covered, fresh, dry and
structural adhesive, low viscosity and high ventilated place out of the reach of children
resistance in low ages. and animals and away from sources of heat.
COMPOUND ADESIVO GEL shows high fluidity,
enabling its application even at places of Packaging
difficult access. • 1 kg (A+B) can
COMPOUND ADESIVO GEL guarantees high • 5 kg (A+B) bucket
yield and excellent adherence to various types
of substracts, being indicated for gluing, even
between them, concrete, iron, wood, stone, etc. Personal protective equipment
COMPOND ADESIVO GEL may be applied on • Safety glasses
humid but not soaked surfaces. • Semifacial mask with appropriate filter for
organic vapours
Fields of application • PVC gloves
• COMPOUND ADESIVO GEL is indicated for: • PVC apron
- gluing;
- concrete repairs;
- grounding;
- fixing with lead;
- special micro-concreting;
- coating and spillways;
- coating of industrial pavement.
Way to use
Preparing the Substract
The surface must be clean and free from dust.
Preparing the Product
Mix well the two components until a gray
colour homogeneous mix is obtained.
118
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 119
COMPOUND ADESIVO PL
Slow structural adhesive, epoxy base.
Characteristics Application
Apply with a flat wall brush, roll or a brush.
Component A: white colour
Clean the tools immediately after use with
Component B: black colour SOLVENTE EPOXY.
First aid:
Component A: item 3 page 209
Component B: item 3 page 209
Approximate consumption
1.6 kg/m² / mm thickness
Density:
Component A+B: 1.60 g/cm³
Basic composition:
Storage
Component A: epoxy resin Stock the product at a covered, fresh, dry and
ventilated place, out of the reach of children
Component B: polyamine-amide and animals and away from sources of heat.
Validity: 12 months
Fields of application
• Gluing: fresh to hard concrete, concrete-
concrete, concrete-iron-wood-tile-ceramics-
stones-fibercement, steel plates.
Way to use
Preparing the Substract
The surface must be clean, dry and free from
dust or loose parts.
Preparing the Product
Mix components A+B, adding all component B
to component A.The mixture must be
performed until a homogeneous uniform colour
consistency gray product is obtained.
119
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 120
Characteristics Storage
Two components Stock the product at a covered, fresh, dry and
First Aid: ventilated place, out of the reach of children
A: item 3, page 209 and animals and away from sources of heat.
B: item 3, page 209
Density: Packaging
A+B: 1.45 g/cm³ • 2 cans (A+B) totaling 1 kg
Basic Composition:
A: epoxy resin Personal protective equipment
B: polyamine-amide • Safety glasses
Validity: 12 months • PVC gloves
• PVC apron
COMPOUND ADESIVO TIX is a high viscosity • Semifacial mask with appropriate filter for
tixotropic structural adhesive. organic vapour
COMPOUND ADESIVO TIX does no run-off even
when applied to vertical surfaces.
COMPOUND ADESIVO TIX is waterproof and
resistant to oils, greases and many chemical
substances.
COMPOUND ADESIVO TIX presents excellent
adherence to different substratum types.
Field of Application
• Caulking, fixing, anchoring and gluing for:
concrete/iron, concrete/concrete, wood, glazed
tile, ceramics and stones.
Way to use
The surface should be perfectly clean and dust
free.
Thoroughly mix the two components preferably
by using a mechanical mixer until obtaining a
perfectly homogeneous gray color.
Apply with a putty knife, within two hours after
mixing.
COMPOUND ADESIVO TIX presents final curing
on the 7th day.
Clean the tools with SOLVENTE EPOXY
immediately after using them.
Wash your hands with water and soap.
Approximate consumption
1.4 kg/m² /mm thickness
120
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 121
COMPOUND GRANITO
Epoxy base, adhesive for rocks.
Characteristics Application
Apply with a mortar board or flat wall brush
Liquid within maximum 1 hour after the mixture is
First aid: done.
Component A: item 3 page 209
Component B: item 3 page 209 Approximate consumption
Density: 1 kg/m²/mm thickness
Component A+B: 1.07 g/cm³
Basic composition:
Component A: epoxy resin
Storage
Stock the product at a covered, fresh, dry and
Component B: polyamine ventilated place, out of the reach of children
Validity: 12 months and animals and away from sources of heat.
Fields of application
• Filling porosity of rocks.
• Recovery of cracks and microsplits.
• Gluing reinforcement textures.
Way to use
Preparing the Substract
The surface must be perfectly clean, dry and
free from dust.
Preparing the Product
Mix well the components of COMPOUND
GRANITO (A+B) preferably with a mechanical
mixer until the obtention of a homogeneous
coloured mass.
121
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 122
COMPOUND INJEÇÃO
Epoxy adhesive for cracking and fissures.
Way to use
Preparation
The fissure should be opened in a V-shape and
all loose material should be removed with
compressed air.
For horizontal fissures, introduce COMPOUND
INJEÇÃO until the fissure is completely filled.
For vertical fissures, 5/16" or 3/8" holes should
be open 30 to 90 cm spaced.
Plastic pipes should be fixed to the holes with
COMPOUND ADESIVO.
Application
Thoroughly mix the two components. Apply
COMPOUND INJEÇÃO to the completely dry
surface and into the holes by using a pneumatic
injector or injection needle. Star from the lowest
fissure point.
122
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 123
Fields of application
• Immediate sealing of:
- metallic tiles, fibercement and concrete;
- hurricane ties, gutter pipes, tile fixing
screws;
- air circulation ducts and air-conditioned
outfits;
- repair on body of closed trucks and
medium vans.
Way to use
Preparing the Substract
The surfaces must be clean, dry and free from
dust.
Application
Cut FITA MULTIUSO AUTO ADESIVA VEDACIT
to desired size, take off the protection film and
apply same over the site, pressing it firmly,
mainly at the edges. Surfaces where dust
covered material is loosened or which do not
permit a perfect adherence of FITA MULTIUSO
AUTO ADESIVA VEDACIT, such as ceramic
tiles and fibercement, firstly they should
receive a coat of NEUTROL or PRIMER MANTA
123
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 124
FIXOTAC
Bituminous glue for timber plate.
Characteristics Attention
Viscous brown liquid • Timber plate laid with FIXOTAC cannot
First Aid: item 1, page 209 receive application®
of hard finish resins
®
such as Synteco or Cascolac .
Density: 0.96 g/cm³
• FIXOTAC is not indicated for gluing parquet.
Basic Composition: bituminous emulsion
• In winter, the product dries more slowly.
Validity: 24 months
Packaging
FIXOTAC is a bituminous glue for timber plate • 1 kg jar
that forms an elastic film highly adherent • 3.6 kg bucket
between the timber plate and floor. • 18 kg bucket
FIXOTAC is water-resistant and follows the • 200 kg drum
movement of wood without loosening the timber
plate.
FIXOTAC requires dry timber plate, free of tar or Personal protective equipment
grit. • Safety glasses
• PVC gloves
Way to use • PVC apron
Apply FIXOTAC to a floor section (approximately
1/2 m² at a time). Remove the excess with a
wooden ruler and leave a 2 mm thick film. Wipe
the excess on the timber plate's lower face.
Glue the timber plate block in position without
tapping it.
About a week, in normal weather conditions
(25°C), the rasping can be done.
Loose Timber Plate
Clean the application area and the lower face of
the loose timber plate.
Apply FIXOTAC either in the floor as in the timber
plate lower face, before fixing it.
Consumption
Approximately 1 kg/m²/mm thickness
Storage
Stock the product at a covered, fresh, dry and
ventilated place, out of the reach of children
and animals and away from sources of heat.
124
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 125
VEDAFIX
Acrylic adhesive and sealant for mortar.
Characteristics Storage
White liquid Stock the product at a covered, fresh, dry and
First Aid: item 4, page 210 ventilated place, out of the reach of children
and animals and away from sources of heat.
Density: 1.01 g/cm³
Basic Composition: acrylic emulsion Attention
Validity: 6 months
VEDAFIX cannot be employed on gypsum or
rolled roughcasting. In these situations, use
BIANCO, high performance adhesive for
Properties roughcasting and mortars.
VEDAFIX is an adhesive and sealant acrylic resin
compatible with cement and lime. Packaging
VEDAFIX has an adhesive action that • 3.6 kg bucket
agglutinates the cement and aggregate particles • 18 kg bucket
thus giving greater workability and adherence of
mortar to the substratum. • 200 kg drum
VEDAFIX prevents shrinkage fissures and
increases resistance to wear. Personal protective equipment
VEDAFIX is also indicated as a sealant primer for • Safety glasses
VEDACIL. • PVC apron
• Rubber gloves
Field of Application
• Mortar for repairs, coatings, floors,
roughcasting, regularization, etc.
• Sealant primer for VEDACIL (acrylic
waterproofing protection for floors and
façades).
Way to use
Mix before using.
The surfaces must be clean, rough, damp and
dust free.
VEDAFIX is added to the mixing water in the
proportion of 1:2 (VEDAFIX: water).
Use 1:2 to 1:3 cement: sand mix depending on
the application.
Approximate Consumption
Mortars and roughcasting - 400 g/m².cm
Sealant primer - 200 g/m²
125
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 126
VEDAFIX SBR
Adhesive for mortar and humidifier, styrene-butadiene base.
Characteristics Storage
White liquid Stock the product at covered, fresh, dry and
First aid: item 4 page 210 ventilated places out of the reach of children
Density: 1.00 g/cm³ and animals and away from sources of heat.
Basic composition: styrene-butadiene
emulsion Attention
Validity: 6 months VEDAFIX SBR should not be used for rolled
humidication in EPS (Isopor®). In this case use
VEDAFIX SBR is an adhesive which provides BIANCO, adhesive of high performance for
great adherence of humidifiers and mortars to humidifiers and mortar.
the different materials.
Shows an optimum workability, besides Packaging
increasing considerably the waterproofness and • 18 kg bucket
mechanical resistance of mortars and concrete. • 200 kg drum
Avoids retraction cracks, apart from increasing
resistance of mortars to wastage and impact.
Personal protective equipment
Fields of application • Safety glasses
• PVC apron
• Waterproof coatings.
• Rubber gloves
• Repair on concrete and mortar.
• Conventional humidifying.
• Pavement.
• Plastifier for plaster cast.
• Admixture for polymer concrete.
Way to use
Preparing the Substract
The surfaces should be clean, rough and
slightly humid.
Preparing the Product
Dilute VEDAFIX SBR in the mixing water in the
proportion of 1 part of VEDAFIX SBR to 2 parts
of water.
Application
Employ proportion of cement/sand varying from
1:1 to 1:3 according to the desired application.
Approximate consumption
300 to 400 g/m²/cm
126
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 127
VEDAPOXI
Epoxy adhesive mass.
Characteristics Storage
Component A: white colour Stock the product in its original and intact
Component B: black colour packaging, at covered, fresh, dry and ventilated
First aid: places out of the reach of children and animals
Component A: item 3 page 209 and away from sources of heat.
Component B: item 3 page 209
Density: Component A+B: 1.66 g/cm³
Attention
Basic compositon: The lower the temperature, specially below
25ºC, the longer it will take for the product to
Component A: epoxy resin and fillers get hard. Under temperatures around 0ºC the
Component B: polyamide and fillers product does not react.
Validity: 12 months Wash hands with water and soap immediately
after use.
VEDAPOXI is an epoxy adhesive mass
designed for professional and household use
which adheres to several materials, such as:
Packaging
wood, metal, stones, ceramics, plastic (except • 100 g box
polyethylene), dishware and glass.
Personal protective equipment
Fields of application • Safety glasses
-VEDAPOXI is for sealing, fixing, moulding and • Semifacial mask with appropriate filter for
repairing the most different objects such as: organic vapours
vases, pipes, water reservoirs, wall tiles, • PVC gloves
strainers, tiles, furniture, etc. • PCV apron
Way to use
Preparing the Substract
The surfaces must be clean and free from fat,
paint and dust.
Mix the two VEDAPOXI components equally,
until a homogeneous gray colour mass is
obtained.
Apply VEDAPOXI, pressing the mass to the
surface.
VEDAPOXI may be painted, rubbed with
sandpaper, bored and sawed, immediately after
2 hours.In order to obtain a smooth finishing,
wet with water the fingers or the tool used for
application and smoothen the surface before it
gets hard.The time it takes to get hard is of 90
minutes at environment temperature.
127
MT 2008 Inglês - 1a Parte.qxd 14/10/2008 15:27 Page 128
128
MT 2008 Inglês - 1a Parte.qxd 14/10/2008 15:27 Page 129
129
MT 2008 Inglês - 1a Parte.qxd 14/10/2008 15:27 Page 130
130
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 131
ACQÜELLA
Water-repellent for façades, based on silicone.
Characteristics Packaging
Silane-siloxane liquid • 900 ml can
First Aid: item 4, page 210 • 3.6 liter can
Density: 0.76 g/cm³ • 18 liter can
Basic Composition: silicone resin • 200 liter drum
Validity: 12 months
Personal protective equipment
ACQÜELLA makes mineral surfaces water- • Safety glasses
repellent thus preventing water penetration. • Semifacial mask with appropriate filter for
ACQÜELLA does not modify the materials organic vapour
appearance. • PVC gloves
On slopped surfaces, dust is removed by rainfall • PVC apron
thus always keeping the surfaces clean.
ACQÜELLA prevents efflorescence, stains and
caulking darkening.
Field of Application
• Apparent concrete.
• Apparent masonry.
• Lithe-ceramic.
• Ceramic roof-tiles.
Previous testing is required for applying to
concrete blocks and lithe-ceramics.
Way to use
Apply ACQÜELLA to perfectly clean and dry
surface.
ACQÜELLA is applied with a broad brush or low-
pressure sprayer in two coats to run off point.
After application, ACQÜELLA requires a minimum
of 6 hours dry weather to dry.
Approximate consumption
Coarse porosity: ................................1 - 2 m²/liter
Medium porosity: ..............................3 - 4 m²/liter
Fine porosity:.....................................5 - 8 m²/liter
Storage
Stock the product at a covered, fresh, dry and
ventilated place, out of the reach of children
and animals and away from sources of heat.
131
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 132
ACQUELLA STONE
Colourless waterproofing material for stones.
132
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 133
ALUMINATION
Liquid aluminum coating.
Characteristics Storage
Thick liquid bright metallic colour Stock the product at a covered, fresh, dry and
First Aid: item 2, page 209 ventilated place, out of the reach of children
and animals and away from sources of heat.
Density: 1.05 g/cm³
Basic Composition: asphalt with aluminum
Validity: 24 months
Packaging
• 3.6 liter can
• 18 liter can
ALUMINATION provides protection and
imperviousness due to its asphalt component Personal protective equipment
complemented by an atomized aluminum
superficial layer. • Safety glasses
While the asphalt layer waterproofs the surfaces, • Semifacial mask with appropriate filter for
the aluminum reflects the sunrays assuring an organic vapour
optimal appearance and long coating durability. • PVC gloves
ALUMINATION also has optimal adherence and • PVC apron
elasticity characteristics.
Field of Application
• Reflective waterproof protection for gutters,
ditches, bins, etc.
• External anti-corrosive protection for cement-
asbestos roof-tiles, tanks, zinc roofing, gutters.
Way to use
The surfaces should be clean, dry and dust free.
Very rough surfaces should be evened.
Galvanized plates require being exposed to
weather for at least 3 months before application.
Thoroughly mix ALUMINATION and apply using a
stock or brush with one generous coat.
ALUMINATION drying time is from 24 to 48
hours under normal weather conditions.
Larger areas subjected to cracking should be
waterproofed with VEDAPREN.
Clean the tools with Turpentine or VEDARRÁS.
Approximate consumption
Rough surfaces: 1 liter /2 m²
Smooth surfaces: 1 liter /3 m²
133
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 16:40 Page 134
AQUASAN
Colourless protection and superficial hardener for concrete floors and structures.
Attention
For floors improperly built that present a
powdered surface, the product effect is very
limited.
134
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 135
ARMATEC
Polymer coat, corrosion inhibitor.
135
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 136
ARMATEC OX 7
Neutralizing agent for rust.
136
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 137
ARMATEC ZN
Anticorrosive zinc base primer for metals.
Characteristics Application
Apply ARMATEC ZN by means of a gun or
Red colour flammable liquid brush, 1 to 2 coats, also awaiting the drying of
First aid: item 3 page 209 the previous coat.
Density: 1.39 g/cm³ When applied in exposed metallic structures,
Basic composition: synthetic resin and zinc this primer may only be used as an anti
chromate corrosive base for finishing paint. Clean the
Validity: 24 months tools with thinner.
137
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 138
CIMENTOL
Waterproof mineral paint.
Characteristics Application
Apply CIMENTOL with painter´s brush or flat
White or gray colour powder wall brush over the previously humidified
First aid: item 4 page 210 surface which should be protected against sun
Basic composition: cement and wind. Apply 2 to 3 coats with an interval of
Validity: 6 months 24 hours between them.Avoid the fast drying of
the paint, humidifying the surface with clean
CIMENTOL is a wateproof paint of long water, using roll 1 to 2 hours after painting.
durability, which has a good appearance for a
longer time. Approximate consumption
Presents excellent adherence over masonry, 150 to 250 g/m²/coat.
concrete and fibercement.
Storage
Fields of application Stock the product in a perfectly dry and
• Outside paint in: ventilated place, obeying the same proceeding
- homes; as for stocking cement.
- buildings;
- industrial sheds;
- bridges.
Attention
- It is recommended that objects be covered so
Way to use as to avoid damage by spatters.
138
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 139
ISOL
Tar-based paint for iron and concrete.
Characteristics Attention
Viscous Liquid - black colour ISOL cannot be used in potable water tanks.
First Aid: item 2, page 209
Density: 1.20 g/cm³ Packaging
Basic Composition: coal tar • 18 liter can
Validity: 24 months • 200 liter drum
Field of Application
• Protective paint on concrete.
• Concrete and iron in hydraulic, sanitary and
harbour works.
Way to use
Surfaces should be dried, cleaned and rust
removed by steel brushing.
Application is made with a stock or waxing brush
by thoroughly scrubbing a small quantity of ISOL.
Once the penetration coat is dry, two more coats
are applied as soon as the previous one has
dried. The topcoats can be applied with a
sprayer.
Clean the tools with SOLVENTE 15.
Approximate consumption
150 ml/m² in 2 coats
200 ml/m² in 3 coats
Storage
Stock the product at a covered, fresh, dry and
ventilated place, out of the reach of children
and animals and away from sources of heat.
139
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 140
MULTISTAIN VEDACIT
Waterproof protector for wood.
Characteristics Application
MULTISTAIN VEDACIT should be applied pure
Amber liquid, flammable in the colours: with a brush or a sheep-wool roll and the coats
translucent, cedar, mahogany, Brazilian walnut, should be spread out (continuously). Between
Brazilian ipê tree. the application of the coats one should obey an
First aid: item 2 page 209 interval of 8 to 12 hours according to the
Density: 0.86 g/cm³ temperature of the environment.
Basic composition: resin, solvents and Number of coats:
additives - Inside surfaces: 2 to 3 coats.
Validity: 24 months - Outside surfaces: 3 to 4 coats.
- Maintenance re-painting: 2 to 3 coats.
MULTISTAIN VEDACIT is a waterproof finishing Obs: when re-painting, wash the surface with
which renders great protection to woods. detergent letting it dry completely. Clean the
Easy to apply has great repelling power to tools with turpentine or VEDARRÁS.
water, and double solar filter providing great
aspect to woods, resistance to bad weather
and long durability.
Approximate consumption
It is supplied in colours and also translucent, 18 to 20 m²/liter/coat
when it intensifies the natural aspect of the
woods, equals its tone and may proportion a Storage
light shine. Stock the product at a covered, fresh, dry and
ventilated place out of the reach of children
Fields of application and animals and away from sources of heat.
• MULTISTAIN VEDACIT is indicated for use on
non-resinous woods, in inside and outside Attention
environments such as decks, gates, frames, Due to the different kind of woods, it is
doors and windows, wainscot, roof structures, suggested that a prior test be carried out,
eaves and lining. applying the product at a non too visible place
so as to observe the final aspect of the
Way to use finishing.
The product is not designed for resinous woods
Preparing the Substract as it may bring about the occurrence of stains.
Wood should be slightly rubbed with sandpaper So as to prevent the attack of termites, the pre-
in the direction of the veins. In sequence application of PENETROL CUPIM is
should be dried and cleaned completely, free indicated.The application of MULTISTAIN
from dust and mould. VEDACIT may take place 24 hours after the
Any treatment which by any chance has been application of PENETROL CUPIM.
dispensed to the wood, such as oil, silicone, It is recommended that objects are covered so
paint or any other product, must be removed to as to avoid damage by spatters.
leave it totally clean and porous.
MAINTENANCE
Preparing the Product MULTISTAIN VEDACIT should be re-applied
Mix before and during the use of the product. approximately every year, according to the type
of wood, the solicitations and conditions to
which the surfaces are exposed.
140
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 141
Packaging
• 900 liters can
• 3.6 liters can
• 200 liters drum
141
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 142
SILICONE VEDACIT
Waterproofing agent for façades and roofs.
Characteristics Storage
Liquid with a silane-siloxane base Stock the product at a covered, fresh, dry and
First aid: item 4 page 210 ventilated place, out of the reach of children
Density: 0.76 g/cm³ and animals and away from sources of heat.
Basic composition: silicone in solvent
Validity: 12 months Attention
It is recommended that objects are covered so
SILICONE VEDACIT repels the rain water, as to avoid damage by spatters.
obstructing that humidity enters the ambients.It
is not paint neither varnish, and thus does not Packaging
alter the natural appearance of the surfaces. • 900 ml can
Avoids the appearance of stains and darkening • 3.6 liters can
of the grouts, apart from providing healthy and • 18 liters can
mouldless ambients.
• 200 liters drum
Fields of application Personal protective equipment
• SILICONE VEDACIT is ideal for:
- apparent bricks ; • Safety glasses
- ceramics; • Semifacial mask with appropriate filter for
- apparent concrete; organic vapours
- ceramic tiles, etc. • PVC gloves
Obs: in ceramics and concrete blocks it is • PVC apron
recommended that pre-tests are carried out.
Way to use
Preparing the Substract
The surfaces must be clean and dry.
Application
Apply SILICONE VEDACIT with a flat wall brush
or a low pressure sprayer in 2 coats sufficiently
satiated to let the product flow off.
SILICONE VEDACIT should be applied in stable
weather, as it demands 6 hours to dry at 25ºC.
Approximate consumption
Large porosity: 1 to 2 m²/liter
Medium porosity: 3 to 4 m²/liter
Small porosity: 5 to 8 m²/liter
142
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 16:40 Page 143
VEDACIL
Waterproof acrylic protection for floors and façades.
Characteristics Storage
Colourless liquid Stock the product at a covered, fresh, dry and
First Aid: item 3, page 209 ventilated place, out of the reach of children
and animals and away from sources of heat.
Density: 0.90 g/cm³
Basic Composition: acrylic resin
Validity: 24 months
Attention
• Neither apply VEDACIL to damp surfaces nor to
waxes, varnishes, etc.
VEDACIL is made from an acrylic resin with high • Surfaces to be treated should be totally dry and
penetrating power. It penetrates the substratum's perfectly clean.
pores by forming a transparent film, highly • Moisture - due to waterproofing failures or
resistant to abrasion and weather. retained in the pieces after washing - causes
VEDACIL does not peel and keeps the material's the surfaces to bleach.
appearance virtually unchanged just accentuating • Waxes, oils, residues of hydrochloric acid or
its natural tones. resins previously applied cause the appearance
VEDACIL assures waterproof surfaces with of superficial stains and poor adherence to the
excellent appearance. product.
VEDACIL increases the resistance to mechanical • When applied to clear surfaces, the product
wearing and facilitates cleaning floors. can make them yellowish.
• For floors subjected to water, check first if the
Field of Application product makes the surface slippery.
• Internal and external protection for floors and • Clean brushes with Thinner.
façades on porous surfaces: apparent concrete,
natural stone, cemented areas, roof-tiles and
industrial floors.
Packaging
• 900 ml can
Way to use • 3.6 liter can
• 18 liter can
Apply to perfectly clean and dry surfaces.
• 200 liter drum
A short bristled paintbrush, broad brush or
sprayer, in two or more coats. Maintain a
minimum 6 hours interval between coats. Personal protective equipment
When treating high-porosity surfaces such as • Safety glasses
apparent concrete, bricks and ceramic roof-tiles, • Semifacial mask with appropriate filter for
an application of a VEDAFIX sealing coat is organic steam
recommended. • PVC gloves
Wait for 24 hours and then apply VEDACIL as • PVC apron
described above.
Approximate consumption
Approximately 8 to 12 m²/liter/coat
143
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 144
VEDACIL MAX
High protection acrylic varnish.
144
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 145
VEDAFIX MAX
Water base acrylic sealer.
Characteristics Storage
White liquid Stock the product at a covered, fresh, dry and
First aid: item 4 page 210 ventilated place, out of the reach of children
Density: 1.02 g/cm³ and animals and away from sources of heat.
Basic composition: acrylic emulsion
Validity: 6 months Packaging
• 3.6 liters bucket
VEDAFIX MAX is an acrylic sealer designed to • 18 liters bucket
unify the porosity of the surfaces.
VEDAFIX MAX is free from styrene and Personal protective equipment
therefore does not turn yellow with the • Safety glasses
influence of ultra violet rays, thus can be • PVC apron
applied also on clear surfaces.
• Rubber gloves
Fields of application
• Sealer for the protection system on:
- apparent concrete;
- apparent masonry;
- natural stones;
- industrial floors.
Obs: VEDAFIX MAX is used as a primer for
VEDACIL MAX, enabling its perfect grounding
on surfaces, apart from avoiding stains and
forming a film with larger thickness.
Way to use
Preparing the Substract
The surface must be clean, dry free from dust,
wax, oils-acid, varnish and resin residues. On
apparent concrete or masonry façades the
surface should be rubbed with sandpaper and
evened first.
Application
Apply a coat of VEDAFIX MAX using a short
hair brush, flat wall brush or a low pressure
sprayer, always during good weather
conditions. Wait for at least 6 hours before
applying VEDACIL MAX for drying purposes.
Approximate consumption
200 ml/m²
145
MT 2008 Inglês - 1a Parte.qxd 14/10/2008 15:27 Page 146
146
MT 2008 Inglês - 1a Parte.qxd 14/10/2008 15:27 Page 147
147
MT 2008 Inglês - 1a Parte.qxd 14/10/2008 15:27 Page 148
148
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 149
BETUME 2
Oxidized asphalt.
Characteristics Protection
After making waterproof, done by means of the
First aid: item 1 page 209 asphaltic rug one must certify the water
Density: 1.01 g/cm³ tightness of the system. For this purpose seal
Basic composition: asphalt the strainers and place a film of water
Validity: 24 months approximately 5 cm high and leave it there for
72 hours.
BETUME 2 is an oxidized asphalt with excellent After the water tightness test, make the
adherence, plasticity and waterproofness. When mechanical protection (mortar bed): at the
used as a structurer it forms a monolitic rug skirting board over the asphaltic rug, fix a
with great adherence to various substracts. metallic woven tissue or similar advancing 20
cm from the floor. Place a separating layer
Fields of application (kraft paper, asphaltic felt) and over it place
mortar (cement and sand in the proportion 1:3)
• Gluing of asphaltic rugs; softening same with BIANCO solution: water
• Reinforcement when there is a flaw in 1:2 and afterwards perform the coating with
waterproofness with the asphaltic rug. mortar (cement and medium size sand in a
proportion 1:3).
Way to use
Preparing the Substract
Approximate consumption
1.0 kg/m²/mm
The surface must be perfectly dry, clean and
evened, with finishing straightened and a fall of
at least 1 % towards the strainers or water Storage
conductors.Sharp edges and borders should be Stock the product at a covered, fresh, dry and
rounded off. ventilated place out of the reach of children
and animals and away from sources of heat.
Application
Gluing of asphaltic rugs Attention
Lay on the first coat of paint on the surface In case of burning do not remove the product
with a coat of NEUTROL or PRIMER MANTA from the skin. Cool the spot with a lot of water
VEDACIT. and look for immediate medical assistance. The
Wait until it dries, an average of 4 to 6 hours, application should preferbably be made by
depending on temperature conditions and qualified professionals.
ventilation of the place.
Heat BETUME 2 to a temperature of 180 to Packaging
220°C. Apply a coat of BETUME 2 with a • 20 kg bag
vegetal fiber broom over the surface which has
been firstly coated. Glue immediately the
asphaltic rug. Press from the center outward to
Personal protective equipment
the edges in order to avoid the building up of • Safety glasses
air bubbles. • Boots
• Scrape gloves
149
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 150
ISOL 2
Emulsion bituminous for concrete and mortars.
Characteristics Packaging
Viscous brown liquid • 1 kg jar
First Aid: item 1, page 209 • 3.6 kg bucket
Density: 1.00 g/cm³ • 18 kg bucket
Basic Composition: bituminous emulsion • 200 kg drum
Validity: 24 months
Personal protective equipment
ISOL 2 forms on the surfaces an elastic and • Safety glasses
waterproof film that resists to water and • PVC gloves
aggressive substances. It can be applied on • PVC apron
moisture surfaces.
ISOL 2 is indicated to concrete and masonry
structures in general.
Field of Application
• Retaining walls
• Foundations, girder beams, footings
• Coatings in soil contact
• Primers in waterproofing
Way to use
The surfaces should be clean and rough.
ISOL 2 is applied as supplied by using a stock or
waxing brush.
Apply ISOL 2 as it is or diluted up to 10 % of
water in two coats. One coat after the other has
dried.
Attention
ISOL 2 cannot be used in water tanks, reservoirs
and metallic surfaces.
Approximate consumption
500 g/m²/in two coats
Storage
Stock the product at a covered, fresh, dry and
ventilated place, out of the reach of children
and animals and away from sources of heat.
150
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 151
NEGROLIN
Bituminous paint for slopes.
Characteristics Storage
Dark brown liquid Stock the product at a covered, fresh, dry and
First Aid: item 1, page 209 ventilated place, out of the reach of children
and animals and away from sources of heat.
Density: 0.96 g/cm³
Basic Composition: bituminous emulsion
Validity: 24 months
Packaging
• 1 liter jar
• 3.6 liter bucket
NEGROLIN is an easily applied, high-yield
bituminous paint. • 18 liter bucket
It forms a waterproof film over damp or dry • 200 liter drum
surfaces.
NEGROLIN can be mixed with sand and grit thus Personal protective equipment
forming a mortar that is resistant to water and • Safety glasses
aggressive substances. • PVC gloves
• PVC apron
Field of Application
• Protecting painting for slopes and ditches
stabilization.
• Filling of joints.
Way to use
The surfaces to be painted should be clean and
rough to assure a good adherence of the
NEGROLIN.
Slopes and Ditches
Stabilization of slopes and ditches is made by
evenly compacting the surfaces. All loose
material should be removed.
Apply NEGROLIN by using a flat-nosed watering
can thus forming a fanned out jet.
Let it dry.
Expansion joints
Filling joints : prepare a mixture of 3 to 4 parts of
medium sand to 1 part of NEGROLIN for filling-
up the joint.
Approximate consumption
Expansion joints: 1 liter NEGROLIN to 3 to 4 liter
of putty.
Slopes and ditches: 2 to 3 liter/m²
151
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 152
NEUTROL
Bituminous paint for concrete and masonry.
152
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 153
NEUTROLIN
Bituminous emulsion paint for concrete and mortar.
Field of Application
• NEUTROLIN is especially indicated for painting
foundations, girder beams, retaining walls,
footings and coatings.
• It is also ideal as primer for asphalt
waterproofing and asphalt paving.
Way to use
The surfaces to be painted should be clean,
rough and floated for good product adherence.
NEUTROLIN is applied as supplied by using a
stock or waxing brush with one penetrating coat
plus two topcoats. A following coat may be
applied as soon as the previous coat has dried.
If necessary, dilute the product with 10 % of
water at maximum.
Approximate consumption
200 ml/m²/coat
Storage
Stock the product at a covered, fresh, dry and
ventilated place, out of the reach of children
and animals and away from sources of heat.
Attention
NEUTROLIN must not be used in potable
153
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 154
Characteristics Attention
Flammable black liquid PICHE EXTRA VEDACIT should not be applied
First aid: item 2 page 209 at potable water reservoirs.In such cases use
Density: 1.18 g/cm³ NEUTROL.
Basic composition: coal tar In order to immunize raw and dry wood apply 2
Validity: 24 months coats of PENETROL CUPIM.
After the product is dry protect with 2 coats of
PICHE EXTRA VEDACIT.
PICHE EXTRA VEDACIT is a coal tar paint.
PICHE EXTRA VEDACIT withstands rain and
sun, avoiding the putrefaction of the wood and
Packaging
the infiltration of water. • 1 liter can
• 3.6 liters can
Fields of application • 18 liters can
• PICHE EXTRA VEDACIT is indicated for: • 200 liters drum
- posts;
- barracks; Personal protective equipment
- hedgerows; • Safety glasses
- stakes; • Semifacial mask with appropriate filter for
- boats; organic vapours
- walls with leaned earth.
• PVC gloves
Way to use • PVC apron
Application
PICHE EXTRA VEDACIT should be applied with
2 coats over dry surfaces, with painter´s or a
large brush. When applied in closed spaces,
assure that the place is well ventilated.
Do not apply in water reservoirs.
Approximate consumption
150 ml/m² with 2 coats
Storage
Stock the product at a covered, fresh, dry and
ventilated place out of the reach of children
and animals and away from sources of heat.
154
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 155
PIXOL EXTRA
Fast drying asphaltic paint.
Characteristics Packaging
Brown colour viscous liquid • 1 liter pot
First aid: item 1 page 209 • 3.6 liters bucket
Density: 1.00 g/cm³ • 18 liters bucket
Basic composition: asphaltic emulsion • 200 liters drum
Validity: 24 months Obs: this product is only traded by Vedacit
do Nordeste S.A
PIXOL EXTRA is an easy to apply waterproof
asphaltic paint. Personal protective equipment
PIXOL EXTRA forms over the surfaces an • Safety glasses
elastic film of high adherence. • PVC gloves
PIXOL EXTRA may be applied to humid • PVC apron
surfaces provided they are not soaked.
Fields of application
• Bedding and foundations in general.
• Coating in contact with the soil.
• Retaining wall.
Way to use
Preparing the Product
Mix before use.
Application
Apply with painter´s or a large brush, 2
coats-one after the drying of the other.
Approximate consumption
250 ml/m²/coat
Storage
Stock the product at a covered, fresh, dry and
ventilated place out of the reach of children
and animals and away from sources of heat.
Attention
PIXOL EXTRA is not to be applied in water
reservoirs and metallic surfaces.In such cases
use NEUTROL.
155
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 156
Characteristics Important
Viscous liquid, black colour - Keep the packages closed, out of children
First Aid: item 3, page 209 reach, animals and far from heat.
Density: 0.92 g/cm³ - Keep the environment ventilated during the
Basic Composition: asphalt in solvent application and drying. Avoid direct contact
Validity: 24 months using protective mask, safe glasses and gloves.
- Do not swallow and avoid the vapor inhalation.
- Flammable product. The package must not be
PRIMER MANTA VEDACIT is a bituminous reused or incinerated.
solution indicated for priming and asphaltic
membranes. Packaging
PRIMER MANTA VEDACIT has quick drying and • 900 ml can
high adherence to concrete on surfaces that will
be waterproofed with asphaltic membranes. • 3.6 liter can
• 18 liter can
Field of Application • 200 liter drum
PRIMER MANTA VEDACIT is indicated for
adhering asphaltic membranes in water Personal protection equipment
reservoirs, slabs, tanks, etc. • Safety glasses
• Semifacial mask with appropriate filter for
Way to use organic vapour
The surface must be regularized, perfectly clean, • PVC gloves
dry and porous. • PVC apron
PRIMER MANTA VEDACIT is cold applied in one
to two coats, with stock or waxing brush.
The asphaltic membrane can be placed 4 to 6
hours after the application, depending on the
local conditions of temperature and ventilation.
Approximate consumption
300 ml/m²/coat
Storage
Stock the product at a covered, fresh, dry and
ventilated place, out of the reach of children
and animals and away from sources of heat.
156
MT 2008 Inglês - 1a Parte.qxd 14/10/2008 15:27 Page 157
157
MT 2008 Inglês - 1a Parte.qxd 14/10/2008 15:27 Page 158
158
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 159
COMPOUND S
Epoxy resin for floors and coatings.
Characteristics Storage
Liquid Stock the product at a covered, fresh, dry and
First Aid: ventilated place, out of the reach of children
A: item 3, page 209 and animals and away from sources of heat.
B: item 3, page 209
Density: Attention
A+B: 1.07 g/cm³ - Utilization of COMPOUND S 200 is indicated for
Basic Composition: damp surfaces.
A: epoxy resin - When you need quick initial cure, it is
B: polyamine-amide recommended COMPOUND S/2.
Validity: 12 months
Packaging
COMPOUND S is a product composed of epoxy • 2 cans totaling 1 kg (A+B)
resin that mixes with quartz sand for obtaining a • 2 cans totaling 4 kg (A+B)
high mechanical strength and chemical
resistance mortar. Personal protection equipment
COMPOUND S has optimal adherence to • Safety glasses
concrete, wood, iron, etc. • Semifacial mask with appropriate filter for
organic vapour
Field of Application • PVC gloves
• Repairs to concrete surfaces (spillways, • PVC apron
highways, floors, etc.)
• Construction of industrial and laboratory floors.
Way to use
Concrete should be dry and free from foreign
substances. The surface should be rough in order
to provide good mortar anchoring.
Mix both COMPOUND S components and add
quartz sand (FILLER for COMPOUND S).
After finishing the job, the tools should be
cleaned with SOLVENTE EPOXY.
Technical Data
• Pot life:......................................2 hours at 25°C
• Initial hardening time:...........................24 hours
• Final hardening time:............................72 hours
Approximate consumption
The COMPOUND S: quartz proportion is up to 1:
5 in weight with an approximate consumption of
300 g/m²/mm thickness.
159
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 160
COMPOUND S 200
Epoxy base resin for floors and coatings.
Characteristics Application
After work is done, tools should be cleaned
Liquid with SOLVENTE EPOXY.
First aid:
Component A: item 3 page 209
Component B: item 3 page 209
Technical data (25ºC)
Initial cure: .........................................24 hours
Density:
Final cure: ..........................................72 hours
Component A+B: 1.10 g/cm³
Pot life:COMPOUND S 200..............20 minutes
Basic composition:
Pot life:COMPOUND S 200+
Component A: epoxy resin FILLER for COMPOUND S ..............90 minutes
Component B: polyamine
Validity: 12 months Approximate consumption
350 g/m² /mm of thickness COMPOUND S
COMPOUND 200 is mixed with quartz sand. 200/quartz, proportion 1: 5 in mass.
Provides a mortar with high mechanical and
chemical resistance.
It is resistant to water, oils, alkali and acids.
Storage
It has excellent adherence to concrete, wood, Stock the product at a covered, fresh, dry and
iron, etc. ventilated place out of the reach of children
and animals and away from sources of heat.
May also be applied to humid surfaces
provided they are not soaked.
Packaging
Fields of application • 1 kg can (A+B)
• COMPOUND S 200 is indicated to coat
concrete surfaces such as: Personal protective equipment
- spillways; • Safety glasses
- industrial floors; • Semifacial mask with appropriate filter for
- garages, etc. organic vapours
• PVC gloves
Way to use • PVC apron
Preparing the Substract
The surface should be rough and free from
dust.
Preparing the Product
Mix well both components of COMPOUND S
200 and add quartz sand (or FILLER to
COMPOUND S).
The proportion of COMPOUND S 200/quartz is
at most 1:5 in mass.
160
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 161
COMPOUND S/2
High fluidity epoxy base resin for floors and coatings.
Characteristics Application
Apply COMPOUND S/2 with a steel mortar
Liquid board or bricklayer´s spoon. After work is done
First aid: tools should be cleaned with SOLVENTE
Component A: item 3 page 209 EPOXY.
Component B: item 3 page 209
Density: Technical data (25 ºC)
Component A+B: 1.10 g/cm³ Initial cure: .........................................24 hours
Basic composition: Final cure: ..........................................72 hours
Component A: epoxy resin Pot life:COMPOUND S/2..................45 minutes
Component B: polyamine Pot life:COMPOUND S/2 +
Validity: 12 months FILLER for COMPOUND S ...1 hour 30 minutes
161
MT 2008 Inglês - 1a Parte.qxd 14/10/2008 15:27 Page 162
162
MT 2008 Inglês - 1a Parte.qxd 14/10/2008 15:27 Page 163
163
MT 2008 Inglês - 1a Parte.qxd 14/10/2008 15:27 Page 164
164
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 165
CARBOLÁSTICO 3
Bituminous putty for sealing.
Characteristics Packaging
Black colour • 1 kg can
First Aid: item 2, page 209 • 4 kg can
Density: 1.2 g/cm³ • 20 kg bucket
Basic Composition: asphalt • 200 kg drum
Validity: 24 months
Personal protective equipment
• Safety glasses
CARBOLÁSTICO 3 is a plastic putty with high • Semifacial mask with appropriate filter for
adherence and imperviousness. organic vapour
It can be applied to concrete, mortar, iron, glass • PVC gloves
and wood.
• PVC apron
CARBOLÁSTICO 3 is supplied ready for use and
it is applied cold.
Field of Application
• Sealing horizontal and vertical joints.
• Filling cracks.
• Caulking gutters, flashing and small boats.
Way to use
The surface should be perfectly dry and clean.
CARBOLÁSTICO 3 is applied as it is with a putty
knife over a previous coat of NEUTROL, letting it
dry for at least 12 hours.
If necessary, CARBOLÁSTICO 3 can be softened
in double boiler.
Use Turpentine or VEDARRÁS to clean tools.
Approximate consumption
1.5 kg/m²/mm
Storage
Stock the product at a covered, fresh, dry and
ventilated place, out of the reach of children
and animals and away from sources of heat.
165
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 166
CARBOLÁSTICO CINZA
Plastic sealing putty.
Characteristics Packaging
Gray putty • 1.7 kg jar
First Aid: item 2, page 209 • 5 kg can
Density: 1.6 g/cm³ • 25 kg bucket.
Basic Composition: alkyd resin
Validity: 12 months Personal protective equipment
• Safety glasses
• Semifacial mask with appropriate filter for
CARBOLÁSTICO CINZA is highly adherent, organic vapour
plastic putty that keeps its characteristics • PVC gloves
over time.
• PVC apron
CARBOLÁSTICO CINZA does not dry out.
Field of Application
CARBOLÁSTICO CINZA is indicated for:
• junctions in general.
• wood, concrete, iron and masonry structures;
• finishing for bolts and nails on fiber cement
roofs;
• seating of glass on skylights and glazing.
Way to use
The base should be dry, clean and dust free.
Apply with a putty knife by firmly pressing the
product against the joint walls.
For low temperatures, it is recommended to
soften CARBOLÁSTICO CINZA in a double boiler.
Keep packaging closed.
Clean the tools with Turpentine or VEDARRÁS.
Approximate consumption
1.6 kg/m²/mm
Storage
Stock the product at a covered, fresh, dry and
ventilated place, out of the reach of children
and animals and away from sources of heat.
166
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 167
EXPANCIT
Polyurethane expansive foam.
167
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 168
Packaging
• 500 ml aerosol (490 g)
168
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 169
FECHATRINCA VEDACIT
Acrylic mass for sealing.
Characteristics Attention
White mass The treating and paint of cracks require
First aid: item 4 page 210 knowledge of a specialized professional. The
Density: 1.76 g/cm³ product may receive paint free from solvent
Basic composition: acrylic resin after it is completely dry (minimum of 24
hours) under normal temperature conditions of
Valdity: 9 months (25°C). For expansion joints subject to
significant moving VEDAFLEX is indicated.
FECHATRINCA VEDACIT features outstanding
resistance to bad weather as well as sun rays.
May be applied to in and outside surfaces.
Packaging
• 550 g cartridge
FECHATRINCA VEDACIT holds paints, free from
solvents, latex or acrylic emulsion base • 6 kg bucket
Approximate consumption
Opening 5 x 5 mm = 21 m/kg.
Storage
Stock the product at a covered, fresh, dry and
ventilated place out of the reach of children
and animals and away from sources of heat.
169
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 170
IMPER CALHA
Sealant for gutter pipes, tiles and hurricane ties.
Characteristics Packaging
White mass • 1.2 kg can
First aid: item 4 page 210 • 1.5 kg pot
Density: 1.5 g/cm³ • 5 kg bucket
Basic composition: acrylic resin with inert
fillers Personal protective equipment
Validity: 12 months • Safety glasses
• PVC apron
IMPER CALHA is a waterproof and flexible • Rubber gloves
sealant applied to the painting form. Has
excellent adherence to ceramic tiles,
fibercement, concrete and galvanized items
which have to be simultaneously rivetted.
Fields of application
• IMPER CALHA is designed to make
waterproof and seal: gutter pipes; tiles;
hurricane ties; dripping-pans; passing pipes
on roof covering.
Way to use
Preparing the Substract
The surface must be perfectly clean, dry and
free from dust and oil.
Application
Apply 2 to 3 fine coats, with a short haired
brush. Wait till superficial drying takes place
between 15 and 60 minutes before applying
the next coat.
Approximate consumption
1.5 kg/m²/mm
Storage
Stock the product at a covered, fresh, dry and
ventilated place out of the reach of children
and animals and away from sources of heat.
170
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 171
JUNTACIT
Plastic putty for sealing roof tiles.
Field of Application
JUNTACIT is especially indicated for:
• cement-asbestos roof sealing
• bolts and flashing sealing
Way to use
The surface should be dry, clean and dust free.
After applying JUNTACIT, utilize a metal putty
knife for pressing the product against the
surface. To obtain a better finish, it is
recommended to wet the putty knife in solvent.
Approximate consumption
1.6 kg/m²/mm
Storage
Stock the product at a covered, fresh, dry and
ventilated place out of the reach of children
and animals and away from sources of heat.
Packaging
• 380 g sachet
• 1.7 kg jar
171
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 172
Characteristics
Gray colour
Basic Composition: PVC
Validity: 12 months
Types
MATA JUNTA VEDACIT has a hollow bulb able of
absorbing the stress, compression and shear
joint movement. The wings allow for perfect
contact with the concrete making water
percolation difficult. Nests and faults near the
wings should be avoided, if necessary, by
reducing the maximum size of the concrete Installation details
aggregate near the member. The installation of MATA JUNTA VEDACIT must
Careful placing is fundamental for MATA JUNTA be in accordance with the following details,
VEDACIT efficiency. depending on the joint type.
The minimum distance between the
MATA JUNTA VEDACIT 035/10 reinforcement bars and the MATA JUNTA
Type 035 - highly stressed joints in dikes, dams, VEDACIT wing should be 1 1/2 times the
large settling tanks, navigation locks, large maximum aggregate size.
reservoirs, etc. For works of great responsibility, especially in
what relates to transversal stability, the
installation of two parallel members is needed.
Welding
Only butt welds should be made at the job site.
Heat the faces simultaneously by juxtaposing
them to a heated metal blade (150°C to 160°C).
When fusion starts, remove the blade while firmly
pressing the MATA JUNTA VEDACIT ends.
MATA JUNTA VEDACIT 022
Type 022 - medium stress joints in settling tanks,
swimming pools, reservoirs, channels, bridges,
viaducts, tunnels, galleries, etc.
172
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 173
Storage
Stock the product at a covered, fresh, dry and
ventilated place out of the reach of children
and animals and away from sources of heat.
Packaging
• Roll - 10 m
• Roll - 20 m
EXPANSION JOINTS
173
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 174
SELACALHA VEDACIT
High adherence sealant for gutter pipes and hurricane ties.
Way to use
Preparing the Substract
The surface must be completely clean and dry,
free from dust and oil.
Application
Cut the nib of the cartridge, place it in the
appropriate gun and apply it to the desired
place.
Superficial drying of the product starts
approximately within 10 minutes after its
application.
174
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 175
VEDACRIL
Acrylic sealing putty.
Characteristics Attention
Mono-coponent - gray and white colours VEDACRIL can only receive solvent-free paint
First Aid: item 4, page 210 after being completely dry. This takes about 7
days.
Density: 1.54 g/cm³
Basic Composition: acrylic resin
Validity: 9 months
Packaging
• 500 g cartridge
• 5 kg bucket
VEDACRIL is characterized by its optimal
resistance to weather and sunrays, it can be Personal protective equipment
applied to both indoor and outdoor surfaces.
• Safety glasses
VEDACRIL accepts latex or acrylic emulsion
paint. • PVC apron
• Rubber gloves
Field of Application
• VEDACRIL is indicated for sealing fissures on
concrete or masonry walls.
• Window framework finishing.
Note: for expansion joints subjected to significant
movement is indicated VEDAFLEX.
Way to use
Apply with special cartridge gun on a totally
clean and dry, dust free surface.
Gaps should be 5 mm at the most.
For outdoor applications, VEDACRIL should be
applied under fine weather conditions so that
during the initial drying (about 4 hours) it does
not receive rain.
Approximate consumption
1 cartridge/13 m (5x5 mm joint)
Storage
Stock the product at a covered, fresh, dry and
ventilated place out of the reach of children
and animals and away from sources of heat.
175
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 16:40 Page 176
VEDAFLEX
Polyurethane sealant.
Characteristics Storage
Mono-component - gray, white and black colours Stock the product at a covered, fresh, dry and
First Aid: item 3, page 209 ventilated place out of the reach of children
and animals and away from sources of heat.
Density: 1.20 g/cm³
Basic Composition: polyurethane
Validity: 12 months
Packaging
• 380 g (310 mL) cartridge
• 830 g (600 mL) sachet
VEDAFLEX is a waterproof sealant. It has optimal
resistance to abrasion, weather and sunrays with Personal protective equipment
no change to its mechanical characteristics. It
presents very good adherence to glass, metal • Safety glasses
and concrete. VEDAFLEX allows for periodic • PVC gloves
movement of the joints. The calculated • PVC apron
permanent elasticity is up to 25%. • Semifacial mask with appropriate filter for
VEDAFLEX does not require primer application. organic vapours
Field of Application
VEDAFLEX is applicable to any type of horizontal
or vertical, indoors or outdoors joint ranging from
6 to 25 mm width. It is also used for placing
glass and sealing window frames and for
caulking in general.
Way to use
The base should be perfectly dry and clean.
Apply with cartridge gun or putty knife, by firmly
pressing the product against the joint walls.
For the correct filling of the joint the tip of the
cartridge should be kept at the bottom of the
joint (supported against the backing material).
Thus, the occlusion of air bubbles is avoided.
In order to limit the depth use polyethylene rope
or polyurethane foam as a backing material.
Superficial curing occurs within 24 hours and
total cure in 7 days.
Note: VEDAFLEX should be applied under good
weather.
Approximate consumption
Joint of 1x1 cm = 3 m/cartridge
176
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 177
VEDAFLEX 45
Polyurethane and bituminous sealant.
Way to use
The surface should be totally dry, clean and free
of dust and oil.
Thoroughly mix the two components (A+B) and
pour the product into the joints that should be
well caulked in order to prevent the sealant
oozing out.
177
MT 2008 Inglês - 1a Parte.qxd 14/10/2008 15:27 Page 178
178
MT 2008 Inglês - 1a Parte.qxd 14/10/2008 15:27 Page 179
179
MT 2008 Inglês - 1a Parte.qxd 14/10/2008 15:27 Page 180
180
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 181
COBERIT
Chlorinated rubber paint.
Way to use
The surface should be rough and totally dry,
clean and dust free.
Apply 2 to 3 coats by using a broad shorthaired
brush and observing a minimum 24 hours
interval between coats.
The first coat can be diluted up to 10 % in
SOLVENTE COBERIT.
Approximate consumption
Approximately 200 ml/ m² /coat
Storage
Stock the product at a covered, fresh, dry and
ventilated place out of the reach of children
and animals and away from sources of heat.
Attention
• Do not apply COBERIT under hot sun or on
rainy days.
• Mortars to be painted must not contain lime.
• Iron surfaces require an application of primer.
181
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 182
COBERIT ACRÍLICO
Acrylic base superficial protection paint.
Way to use
Preparing the Substract
The surface must be clean, dry and free from
dust.
Preparing the Product
Make homogeneous before using.
Application
Use a sheep wool roll or a flat wall brush, apply
a coat of COBERIT ACRÍLICO diluted in 5 to
10 % SOLVENT COBERIT. After the first coat is
dry which comes about in approximately 6
hours, apply a maximum of two more coats
always waiting for the complete drying of the
previous coat. In case of excessively porous
182
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 183
COBERIT EPOXY
Epoxy paint.
183
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 184
COBERIT TRÁFEGO
Traffic marking acrylic paint.
Characteristics Packaging
Yellow and white • 3.6 liter can
First Aid: item 2, page 209 • 18 liter bucket
Density: 1.50 (yellow) e 1.43 (white) g/cm³
Basic Composition: acrylic resin Personal protective equipment
Validity: 24 months • Safety glasses
• Semifacial mask with appropriate filter for
organic vapour
COBERIT TRÁFEGO assures optimal visibility and • PVC gloves
durability for signaling. It offers resistance to • PVC apron
water, sun and to wearing caused by vehicles or
pedestrians. It has excellent adherence to
asphalt, cemented floors and concrete.
COBERIT TRÁFEGO is a quick-dry paint. In
approximately 30 minutes (25°C) the area can be
released to traffic.
COBERIT TRÁFEGO is supplied in two colors:
white and yellow.
Field of Application
• Safety lanes in plants, ground marking for
parking lots and highways, pedestrian or
vehicle stripped lanes in supermarkets, malls,
buildings, stores, etc.
Way to use
The surface should be perfectly dry, clean and
dust free.
COBERIT TRÁFEGO is applied by using a broad
brush, roller or sprayer, in one or two coats.
If necessary, dilute to a maximum 5 % in solvent.
SOLVENTE COBERIT is used for diluting the paint
or cleaning the tools.
Approximate consumption
350 ml/ m²/coat for approximately 45 microns
film
Storage
Stock the product at a covered, fresh, dry and
ventilated place out of the reach of children
and animals and away from sources of heat.
184
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 185
Field of Application
• It is utilized over concrete and iron, in hydraulic
works, sanitary sewer systems, piping,
harbours, docks and floodgates.
• Do not apply to potable water reservoirs.
Way to use
The surface should be porous and perfectly dry
and clean and from dust free and oils. On iron,
apply previously a primer.
Thoroughly mix the two components (A+B),
preferably by utilizing a mechanical mixer.
Apply 2 to 4 coats of COMPOUND COAL TAR
EPOXY by using a broad brush.
The interval between coats is of 8 hours at least.
The total drying takes place in 8 days in normal
weather conditions.
If necessary, dilute the first coat to a maximum of
5 % with SOLVENTE COBERIT.
185
MT 2008 Inglês - 1a Parte.qxd 14/10/2008 15:27 Page 186
186
MT 2008 Inglês - 1a Parte.qxd 14/10/2008 15:27 Page 187
187
MT 2008 Inglês - 1a Parte.qxd 14/10/2008 15:27 Page 188
188
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 189
PENETROL CUPIM
Colourless preservative for dressed lumber.
Characteristics Storage
Colourless flammable liquid Stock the product at a covered, fresh, dry and
First Aid: item 4, page 210 ventilated place out of the reach of children
and animals and away from sources of heat.
Density: 0.78 g/cm³
Basic Composition: deltamethrin and kerosene
Validity: 24 months
Packaging
• 300 ml aerosol
• 900 ml can
The powerful insecticide action of PENETROL • 3.6 liter can
CUPIM protects dry wood against attack by • 18 liter bucket
termites and woodborers. It is colourless and • 200 liter drum
allows for any treatment to wood: varnish, wax or
paint, soon after 24 hours.
Personal protective equipment
Field of Application • Safety glasses
• All dry woods: civil construction, furniture • Semifacial mask with appropriate filter for
industry, etc. organic vapour
• PVC gloves
Way to use • PVC apron
The wood should be dry and without any type of
finishing.
Apply 2 rich coats of PENETROL CUPIM by using
a stock brush or paint brush. Let the first coat
liquid to penetrate and then apply the second
coat. For already attacked woods, inject the
product into the orifices already existing on the
wood.
Attention
• Keep PENETROL CUPIM away from fire.
• Since it is poisoning, keep it away from food
and children's reach.
• Always apply at a ventilated location.
• For domestic use, especially for furniture and
other attacked woods inside homes, it is
recommended to apply PENETROL CUPIM only
into the existing orifices by using a syringe or
the aerosol packaging.
Approximate consumption
7 to 10 m² /liter, depending on porosity
189
MT 2008 Inglês - 1a Parte.qxd 14/10/2008 15:27 Page 190
190
MT 2008 Inglês - 1a Parte.qxd 14/10/2008 15:27 Page 191
191
MT 2008 Inglês - 1a Parte.qxd 14/10/2008 15:27 Page 192
192
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 193
Fields of application
It is indicated for waterproof protection and
thermal insulator to covering of buildings.
Way to use
Application
Unroll MANTA SUBCOBERTURA VEDACIT,
superposing 10 cm between the stripes, always
starting at the edges and perpendicular to the
roof timbers. The adoption of trusses is
desirable, over which the roof timbers and the
shingles will be placed, thus obtaining a
spacing between 3 and 10 cm which
determines the forming of an air bed
responsible for better thermal comfort to
environments.
Storage
Stock the product at a covered, fresh, dry and
ventilated place, out of the reach of children
and animals and away from sources of heat.
Packaging
• Roll of 25 m²
• Roll of 50 m²
193
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 194
TARUCEL VEDACIT
Deepness delimiter and support for joints and frames.
Characteristics
Colours: graphite and white
Basic composition: polyethylene
Validity: 24 months
Fields of application
TARUCEL VEDACIT is indicated as a support
body for preparing joints for the application of
sealants and as protection and filling of
aluminum frames.
Packaging
- 6 mm x 500 m
- 8 mm x 500 m
- 10 mm x 400 m
- 15 mm x 100 m
- 18 mm x 100 m
- 18 mm x 300 m
- 20 mm x 100 m
- 20 mm x 200 m
194
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 195
VEDARRÁS
Mineral multiuse solvent.
Fields of application
• It is indicated for industries, workshops,
paintings and domestic use.
Storage
Stock the product at a covered, fresh, dry and
ventilated place out of the reach of children
and animals and away from sources of heat.
Attention
- Do not swallow the product and avoid the
inhaling of the vapours.
- Keep the place ventilated during application
and drying.
- Avoid direct contact with the product, using
mask, safety eye glasses and gloves.
Packaging
• 900 ml can
• 5 liters can
Obs: the product is only traded by Vedacit
Nordeste S.A.
195
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 196
VEDATEX
Polyester woven fabric structurer.
Fields of application
• VEDATEX is used as structurer in:
- moulded waterproofness performed at site;
- treating cracks, splits and expanding joints.
Way to use
Application
Place VEDATEX between the first and second
waterproofing layers and cover afterwards with
the following layers so that the woven fabric
does not appear.
In slabs: transpass 10 cm between the joints.
Cracks and splits: place, surpassing at least
5 cm at each side.
Storage
Stock the product at a covered, fresh, dry and
ventilated place out of the reach of children
and animals and away from sources of heat
Packaging
• Roll 0.5 x 50 m
• Pack of 0.75 x 10 m
• Roll of 0.75 x 50 m
• Roll of 1.5 x 50 m
196
MT 2008 InglŒs - 2a Parte.qxd 14/10/2008 15:22 Page 197
VEDATEX ANTIFISSURA
Synthetic fiber membrane for painting reinforcement.
Way to use
Application
1. Remove the mass excess and old paint.
Smoothen the surface, checking that it is dry
and free from dust. Fill first the larger cracks
with VEDACRIL.
2. Paint a horizontal stripe of paint, applying
simultaneously VEDATEX ANTIFISSURA.
3. Simultaneously glue VEDATEX ANTIFISSURA
over the painted stripe in the vertical
direction.
4. Apply a coat with abundant paint over the
membrane, gluing it to the wall.
5. After the first coat is dry, the texture
produced by the VEDATEX ANTIFISSURA
fibers becomes visible. Apply another final
coating of paint, so as to cover it.
6. Repeat steps 2 to 5 for the other straps.
197
MT 2008 Inglês - 1a Parte.qxd 14/10/2008 15:27 Page 198
198
MT 2008 Inglês - 1a Parte.qxd 14/10/2008 15:27 Page 199
Tables:
Painting Systems - Chemical Protection ................................................................................................201
Chemical resistance at environment temperature (25ºC)) .....................................................................202
First Aid ..................................................................................................................................................203
Subsidiaries and Technical Assistance..................................................................................................205
199
MT 2008 Inglês - 1a Parte.qxd 14/10/2008 15:27 Page 200
200
Primer Finishing
Drying and
Surface Prepare Drying Nº Intervals
Product Nº coats Product Colour cure time
time coats between coats
Compound Coal Tar
Clean and Epoxy diluted Compound
1 8h 2a3 8h Black 7 days
dry in 5% of Coal Tar Epoxy
Aggressive
Solvente Epoxy
Submerse *
The same Isol 1 12 h Isol 2 12 h Black 7 days
MT 2008 Inglês - 1a Parte.qxd
Ferrous surfaces
Ambient
The same Armatec ZN 1 to 2 8h Enamel 2 24 h Assorted 3 days
Non-
14/10/2008
Submerse *
The same and S 200 without - - 1 - Yellowish 7 days
and S 200 + Filler
Page 201
Aggressive
Filler
Concrete surfaces
Ambient
Colourless
The same Vedafix Max 1 8h Vedacil Max 2 24 h 3 days
Non-
with shine
* Surfaces considered to be submersed after application of protection in non-drinkable water. **Settled surface without released particles or dust.
201
MT 2008 Inglês - 1a Parte.qxd 14/10/2008 15:27 Page 202
Coberit
Neutrol
Epoxy
Isol
Product
ACIDS
Acetic up to 5% - R - R R
Acetic up to 10% - NR - R R
Acetic up to 20% - NR - R R
Hydrochloric up to 5% R R - R NR
Hydrochloric up to 10% R R NR R NR
Hydrochloric up to 30% R RL NR R NR
Phosphoric up to 5% R R R R R
Phosphoric up to 10% R R RL R NR
Phosphoric up to 50% - R NR R NR
Nitric up to 5% R R NR R NR
Sulfuric up to 10% R R R R R
Sulfuric up to 25% R R R R R
Oleic NR R - NR NR
ALKALIS
Ammonium Hydroxide up to 5% R R R R R
Ammonium Hydroxide up to 20% R R RL R RL
Calcium Hydroxide R R R R R
Potassium Hydroxide up to 15% R R RL R RL
Sodium Hidroxide up to 10% R R R R R
Sodium Hidroxide up to 15% R R R R R
INORGANIC SALTS
Calcium Chloride R R R R R
Sodium Chloride R R R R R
Sodium Phosphate R R R R R
OILS AND GREASES
Animal NR R R NR NR
Mineral R R R NR NR
Vegetal NR R R NR NR
OXIDANT AGENTS
Sodium Hypochlorite NR NR NR NR NR
SOLVENTS
Aliphatic Hydrocarbons RL R R NR NR
Aromatic Hydrocarbons NR R NR NR NR
Esters NR R NR NR NR
LEGEND: R - Resistant; RL - Limited Resistance; NR - Non-Resistant
202
MT 2008 Inglês - 1a Parte.qxd 14/10/2008 15:27 Page 203
- Skin contact: remove the product with clean cloth, vegetal oil.
Wash with plenty of water and soap. Apply hydrating cream.
- Eye contact: wash with plenty of water for at least 15 minutes.
Look for a doctor.
- Inhalation: remove to fresh and well-ventilated ambient.
- Ingestion: do not nauseate. Look for a doctor.
- Skin contact: remove the product with clean cloth and wash with
plenty of water and soap. Apply hydrating cream.
- Eye contact: wash with plenty of water for at least 15 minutes.
Look for a doctor.
- Inhalation: remove to fresh and well-ventilated ambient.
- Ingestion: do not nauseate. Look for a doctor.
- If the product has already dried on the skin, remove with vegetal
oil. Wash with plenty of water and soap. Apply hydrating cream.
203
MT 2008 Inglês - 1a Parte.qxd 14/10/2008 15:27 Page 204
204
MT 2008 Inglês - 3a Parte.qxd 24/10/2008 08:48 Page 205
CEARÁ PERNAMBUCO
Vedacit do Nordeste S.A. Vedacit do Nordeste S.A.
Filial Fortaleza Filial Recife
Av. Santos Dumont, 1740 - Sala 607 Av. Conselheiro Aguiar, 4887 - sala 108 - 2° andar
Fortaleza - CE Edifício Marisol - Boa Viagem - Recife - PE
Phone: (55-85) 3261.9855 - Fax: (55-85) 3261.9692 Phone/Fax: (55-81) 3465.7166
E-mail: ce@vedacit.com.br E-mail: pe@vedacit.com.br
Representatives
ACRE GRR Representações Comerciais Ltda.
França e Carvalho & Cia. Ltda. Phone: (55-71) 9129.1359
Phone: (55-69) 8111.2083 / (55-69) 8111.2077 Fax: (55-71) 3354.0738
Fax: (55-69) 3224.7667 E-mail: grrltda@ig.com.br
E-mail: fcarvalho@enter-net.com.br
• VITÓRIA DA CONQUISTA
ALAGOAS Neves & Andrade Ltda.
Brito Representações Ltda. Phone: (55-77) 9989.2567
Phone: (55-82) 8845.3919 Fax: (55-77) 3426.2691
Fax: (55-82) 3338.1933 E-mail: neveseandrade@uol.com.br
E-mail: vendas@britorepresentacoes.com.br
AMAPÁ CEARÁ
Contrat Representações Ltda. • FORTALEZA
Phone: (55-96) 9972.9259 Guarines&Guarines Representações Ltda.
Fax: (55-96) 3217.4823 Phone: (55-85) 9132.8238
E-mail: contratltda@uol.com.br
Fax: (55-85) 3257.5277
AMAZONAS E-mail: guarinesrep@uol.com.br
Taciba Representações Ltda. • JUAZEIRO DO NORTE
Phone: (55-82) 9116.8235 Genival Comércio Representações Ltda.
Fax: (55-82) 3648.2404
E-mail: taciba@vivax.com.br Phone: (55-88) 9214.8587
Fax: (55-88) 3512.1595
BAHIA E-mail:genivalrepresentacoes@genivalrepresentacoes.com.br
• FEIRA DE SANTANA
C.W. Representações Ltda.
DISTRITO FEDERAL
Phone: (55-75) 9131.6063 • BRASÍLIA / PLANO PILOTO
Fax: (55-75) 3221.4657
E-mail: r.correia@uol.com.br Alterosa Repres. Com. Ltda.
Phone: (55-61) 9985.9018
• ITABUNA Fax: (55-61) 3435.3873
Roiber Representações Ltda. E-mail: anderson.alterosa@ibest.com.br
Phone: (55-73) 8106.8772
Fax: (55-73) 3613.8083 • GAMA
E-mail: roiberep@terra.com.br
FAL Repres. Com. Ltda.
• LAURO DE FREITAS Phone: (55-61) 9973.3733
D'Martins Comércio e Representações Ltda. Fax: (55-61) 3556.0059
Phone: (55-71) 9982.1510 E-mail: falrepresentacao@uol.com.br
Fax: (55-71) 3369.0104
E-mail:dmartinsltda@terra.com.br
ESPÍRITO SANTO
• SALVADOR
Coril Representações Ltda.
Portugal Representações Ltda.
Phone: (55-27) 9981.6902
Phone: (55-71) 9983.6407
Fax: (55-71) 3375.4444 Fax: (55-27) 3225.0477
E-mail: cporcarlos@aol.com E-mail: atendimento@coril.com.br
206
MT 2008 Inglês - 3a Parte.qxd 24/10/2008 08:48 Page 207
• IPATINGA • MARABÁ
Vaz & Fernandes Ltda. Tocantins Representações Ltda.
Phone: (55-31) 8773.8788 Phone: (55-99) 8111.0081 / (55-99) 8111.0299
Fax: (55-31) 3826.7906 Fax: (55-99) 3525.5505
E-mail: magnorepresenta110@hotmail.com E-mail: tocantins@representacoes.net
• ITAJUBÁ • SANTARÉM
W & W Representações Ltda. Endara Representações Ltda.
Phone: (55-35) 9986.2793 Phone: (55-93) 9653.7031
Fax: (55-35) 3622.6706 Fax: (55-93) 3524.1028
E-mail: luizwood@yahoo.com.br E-mail: endara@netsan.com.br
• JUIZ DE FORA
Cemabe Com. Mat. Constr. PARANÁ
Representações Ltda.
• APUCARANA
Phone: (55-32) 9988.7777
Fax: (55-32) 3422.2433 Pirani Representações Comerciais Ltda
E-mail: cemabecelso@terra.com.br Phone: (55-43) 9961.0591
Fax: (55-43) 3256.2844
• MONTES CLAROS E-mail: sergiopirani@uol.com.br
Giljan Representações Ltda.
Phone: (55-38) 9986.4499
• CAMPO MOURÃO
Fax: (55-38) 3221.7947 N. Navarro Júnior & Cia Ltda
E-mail: giljan@veloxmail.com.br Phone: (55-44) 8812.7228
Fax: (55-44) 3034.8463
• POÇOS DE CALDAS E-mail: nnavarrojr@hotmail.com
Viti Representações Ltda.
Phone: (55-35) 8409.6277 / (55-35) 8414.8926 • CASCAVEL
Fax: (55-35) 3721.3930 Luiz P. Romancini & Cia Ltda.
E-mail: egviti@oi.com.br Phone: (55-45) 9972.2358
Fax: (55-45) 3378.1689
• TEÓFILO OTONI
E-mail: luizpr@brturbo.com.br /
Robson Campos Representações Ltda. luizpromancini@hotmail.com
Phone: (55-33) 9964.4244 / (55-33) 8805.1244
Fax: (55-33) 3522.6061 • CURITIBA
E-mail: camposrepresentacoes@oi.com.br J.A Rollo & Cia Ltda.
Phone: (55-41) 9914.1101
• UBERLÂNDIA Tel.: (55-41) 3022.1222
Sipa Representações Comerciais Ltda. E-mail: rollors@ig.com.br
Phone: (55-34) 9971.0350 / (55-34) 9196.0550
Fax: (55-34) 3254.5894 Muriá Representações Comerciais Ltda.
E-mail: siparepresentacoes@terra.com.br Phone: (55-41) 9975.6179
Fax: (55-41) 3029.2216
E-mail: muriarepcom@yahoo.com.br
PARÁ
• GRANDE CURITIBA
• BELÉM BR Sampaio Representações
NJ Comércio e Representação Ltda. Comerciais Ltda.
Phone: (55-91) 8862.8538 Phone: (55-41) 9991.1257
Fax: (55-91) 3245.1928 Fax: (55-41) 3015.4090 / (55-41) 3023.2424
E-mail: castorinorep@uol.com.br E-mail: renatocsampaio@yahoo.com.br
208
MT 2008 Inglês - 3a Parte.qxd 24/10/2008 08:48 Page 209
• CAMPINAS • MAUÁ
Zaira & Gomes Repres. Coms. Ltda. Araki Repres. Com. S/C Ltda.
Phone: (55-19) 9117.8414 Phone: (55-11) 9919.7573 / (55-11) 9368.6165
Fax: (55-19) 3579.3362 Fax: (55-11) 4109.9534
E-mail: vedacitcamp@uol.com.br / E-mail: arakirepresentacoes@uol.com.br
zaira.gomes@uol.com.br • OSASCO
• COTIA Representações Vladmir
HDS Repres. Materiais de Construção Ltda ME. Garcia & Cia Ltda.
Phone: (55-11) 7809.4626 Phone: (55-11) 9816.6777
Fax: (55-11) 3781.9989 Fax: (55-11) 3868.4256
E-mail: pradodada@uol.com.br E-mail: repgv@ig.com.br
• FRANCA • OURINHOS
LEP Com. Repres. Mat. Construção. Andrex Repres. Comerciais Ltda.
Phone: (55-16) 9147.0059 Phone: (55-14) 9749.8562
Fax: (55-16) 3720.2430 Fax: (55-14) 3322.3937
E-mail: pilotto@uol.com.br E-mail: andrexveda@uol.com.br
• FERRAZ DE VASCONCELOS • PIRACICABA
Silfran Repres. S/C Ltda. P.W. Representações S/C Ltda.
Phone: (55-11) 9274.1037 Phone: (55-19) 9788.0000
Fax: (55-11) 2944.7823 Fax: (55-19) 3421.3043
E-mail: franciscoassissilva@uol.com.br E-mail: pwrg@uol.com.br
212
MT 2008 Inglês - 1a Parte.qxd 24/10/2008 09:45 Page 213
Notes
213
MT 2008 Inglês - 1a Parte.qxd 24/10/2008 09:45 Page 214
Notes
214