Beruflich Dokumente
Kultur Dokumente
--``,`,,`,,,``,``,,```,``,,```-`-`,,`,,`,`,,`---
Part 5: Dimensioning of structural metal work
Uncontrolled copy
Not for when printed 00376 BTMXN01, 2019-01-30
Provided by IHS Markit under license with BSI - Uncontrolled Copy Licensee=Bombardier Extract/5957305002
No reproduction or networking permitted without license from IHS Resale, 06/05/2018 11:35:43 MDT
BS ISO 129‑5:2018 BRITISH STANDARD
National foreword
This British Standard is the UK implementation of ISO 129‑5:2018.
The UK participation in its preparation was entrusted to Technical
Committee TDW/4, Technical Product Realization.
A list of organizations represented on this committee can be obtained on
request to its secretary.
This publication does not purport to include all the necessary provisions
of a contract. Users are responsible for its correct application.
© The British Standards Institution 2018
Published by BSI Standards Limited 2018
ISBN 978 0 580 89718 4
ICS 01.100.01
Compliance with a British Standard cannot confer immunity from
legal obligations.
This British Standard was published under the authority of the
Standards Policy and Strategy Committee on 30 April 2018.
--``,`,,`,,,``,``,,```,``,,```-`-`,,`,,`,`,,`---
Uncontrolled copy
Not for when printed 00376 BTMXN01, 2019-01-30
Provided by IHS Markit under license with BSI - Uncontrolled Copy Licensee=Bombardier Extract/5957305002
No reproduction or networking permitted without license from IHS Resale, 06/05/2018 11:35:43 MDT
BS ISO 129‑5:2018
INTERNATIONAL ISO
STANDARD 129-5
First edition
2018-04-01
--``,`,,`,,,``,``,,```,``,,```-`-`,,`,,`,`,,`---
Reference number
ISO 129-5:2018(E)
--``,`,,`,,,``,``,,```,``,,```-`-`,,`,,`,`,,`---
ii
Copyright British Standards Institution © ISO 2018 – All rights reserved
Uncontrolled copy when printed 00376 BTMXN01, 2019-01-30
Provided by IHS Markit under license with BSI - Uncontrolled Copy Licensee=Bombardier Extract/5957305002
No reproduction or networking permitted without license from IHS Not for Resale, 06/05/2018 11:35:43 MDT
BS ISO 129‑5:2018
ISO 129‑5:2018
Contents Page
Foreword......................................................................................................................................................................................................................................... iv
1 Scope.................................................................................................................................................................................................................................. 1
2 Normative references....................................................................................................................................................................................... 1
3 Terms and definitions...................................................................................................................................................................................... 1
4 Basic requirements............................................................................................................................................................................................. 2
5 Simplified dimensioning of structural metal work........................................................................................................... 2
6 Dimensioning of component profile................................................................................................................................................. 2
6.1 Profile code................................................................................................................................................................................................. 2
6.2 Dimensioning samples...................................................................................................................................................................... 3
6.3 Profile dimensioning in drawing.............................................................................................................................................. 7
7 Detail requirement............................................................................................................................................................................................. 9
7.1 Typical component dimensioning........................................................................................................................................... 9
7.2 Dimensioning of bolts and rivets.......................................................................................................................................... 12
7.3 Dimensioning of welding components............................................................................................................................. 12
Annex A (normative) Profile graphical symbols....................................................................................................................................14
Annex B (informative) Dimensioning of weld components........................................................................................................16
--``,`,,`,,,``,``,,```,``,,```-`-`,,`,,`,`,,`---
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
--``,`,,`,,,``,``,,```,``,,```-`-`,,`,,`,`,,`---
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following
URL: www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 10, Technical product documentation,
Subcommittee SC 6, Mechanical engineering documentation.
A list of all parts in the ISO 129 series can be found on the ISO website.
iv
Copyright British Standards Institution © ISO 2018 – All rights reserved
Uncontrolled copy when printed 00376 BTMXN01, 2019-01-30
Provided by IHS Markit under license with BSI - Uncontrolled Copy Licensee=Bombardier Extract/5957305002
No reproduction or networking permitted without license from IHS Not for Resale, 06/05/2018 11:35:43 MDT
BS ISO 129‑5:2018
INTERNATIONAL STANDARD ISO 129‑5:2018
1 Scope
This document specifies the dimensioning of drawings for general use on structural metal work mainly
consisting of plates, bars and profile sections.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 129‑1, Technical drawings — Indication of dimensions and tolerances Part 1: General principles
ISO 129‑4, Technical product documentation (TPD) — Indication of dimensions and tolerances — Part 4:
Dimensioning of shipbuilding drawings
ISO 5261:1995, Technical drawings — Simplified representation of bars and profile sections
ISO 657‑1, Hot-rolled steel sections — Part 1: Equal-leg angles — Dimensions
ISO 657‑2, Hot-rolled steel sections — Part 2: Unequal-leg angles — Dimensions
ISO 657‑16, Hot-rolled steel sections — Part 16: Sloping flange column sections (metric series) — Dimensions
and sectional properties
ISO 657‑18, Hot-rolled steel sections — Part 18: L sections for shipbuilding (metric series) — Dimensions,
sectional properties and tolerances
ISO 657‑21, Hot-rolled steel sections — Part 21: T-sections with equal depth and flange width — Dimensions
ISO 10209, Technical product documentation — Vocabulary — Terms relating to technical drawings,
product definition and related documentation
--``,`,,`,,,``,``,,```,``,,```-`-`,,`,,`,`,,`---
4 Basic requirements
Basic requirements of dimensioning are as follows:
a) The indication of dimensions and tolerances shall follow the general principles specified
in ISO 129‑1.
b) The dimensions of structural metal work shall be simple and clear. The standard plates and profile
sections should be represented with code.
c) The datum line of dimensioning should be the centroidal line of component.
To maintain readability of drawings and to simplify drawing, dimension lines can be omitted as shown
in Figure 1.
by ISO 5261.
The arc length of a circular structure in the frame should be dimensioned on one side of its line. An
example is shown in Figure 1.
2
Copyright British Standards Institution © ISO 2018 – All rights reserved
Uncontrolled copy when printed 00376 BTMXN01, 2019-01-30
Provided by IHS Markit under license with BSI - Uncontrolled Copy Licensee=Bombardier Extract/5957305002
No reproduction or networking permitted without license from IHS Not for Resale, 06/05/2018 11:35:43 MDT
BS ISO 129‑5:2018
ISO 129‑5:2018
--``,`,,`,,,``,``,,```,``,,```-`-`,,`,,`,`,,`---
H × B × t − L
4 I-beam section Shall conform to the or
designation specified
by ISO 5261:1995, Table 2 I H × B × t − L
B × t
9 Plate
L
Rectangular hollow
10 H × B × t − L
section
4
--``,`,,`,,,``,``,,```,``,,```-`-`,,`,,`,`,,`---
Double round-headed
2 A × B × R − L
flats
Unequal round-headed
3 A × B × R1 × R2 − L
flats
Right-angled trapezoid
10 A × B × H × t − L
tube
--``,`,,`,,,``,``,,```,``,,```-`-`,,`,,`,`,,`---
Thin-walled channel
4 C H × B × t − L
section
C H × B × t − L
8 Z-section Z or
C Z H × B × t − L
6
--``,`,,`,,,``,``,,```,``,,```-`-`,,`,,`,`,,`---
Graphical Letter
No. Classification Shape of section Representation
symbol code
Thin-walled oblique
10 C H × B × A × t − L
lip Z section
Shall conform to
11 Thin-walled square tube C B × t − L
ISO 129‑1:2017, Figure A.2
Thin-walled welding
12 C ∅ D × t − L
circular tube
--``,`,,`,,,``,``,,```,``,,```-`-`,,`,,`,`,,`---
a)
b)
The size and specification of a component could be indicated by a leader line. The cutting length in
profile code can be omitted when it has been presented in the schematic drawing and the general
drawing. See Figure 3 b).
The number of components shall be indicated in front of the specification, see Figure 3.
When the number of components is large, they should be numbered in the drawing, and the sizes and
specifications presented in appropriate columns in a table. See Figure 4.
8
Copyright British Standards Institution © ISO 2018 – All rights reserved
Uncontrolled copy when printed 00376 BTMXN01, 2019-01-30
Provided by IHS Markit under license with BSI - Uncontrolled Copy Licensee=Bombardier Extract/5957305002
No reproduction or networking permitted without license from IHS Not for Resale, 06/05/2018 11:35:43 MDT
BS ISO 129‑5:2018
ISO 129‑5:2018
7 Detail requirement
On a cutting plate drawing, the size of features should be dimensioned in the direction of the main axes.
See Figure 6.
--``,`,,`,,,``,``,,```,``,,```-`-`,,`,,`,`,,`---
The position of centroidal lines shall be indicated in the drawing. When the centroidal lines of two
adjacent components are close, they shall be separated in the intersection area before dimensioning,
see Figure 7.
--``,`,,`,,,``,``,,```,``,,```-`-`,,`,,`,`,,`---
The width of one leg of an unequal leg angle component shall be dimensioned, see Figure 8.
For the connection part of components, the following features shall be dimensioned (see Figure 9):
a) the size of the gusset plate;
b) the location of bolt hole centres and centre distance of all components;
c) the distance between component end and intersection point of datum lines.
10
Copyright British Standards Institution © ISO 2018 – All rights reserved
Uncontrolled copy when printed 00376 BTMXN01, 2019-01-30
Provided by IHS Markit under license with BSI - Uncontrolled Copy Licensee=Bombardier Extract/5957305002
No reproduction or networking permitted without license from IHS Not for Resale, 06/05/2018 11:35:43 MDT
BS ISO 129‑5:2018
ISO 129‑5:2018
For double profile combined component, the number and size of batten plates shall be indicated,
see Figure 10. The number and profile specification shall be located above the leader line, with the
length beneath.
For gusset plates, the following features shall be dimensioned (see Figure 11):
a) the size of the gusset plate;
b) the distance between bolt holes and intersection points of component centroidal lines.
--``,`,,`,,,``,``,,```,``,,```-`-`,,`,,`,`,,`---
--``,`,,`,,,``,``,,```,``,,```-`-`,,`,,`,`,,`---
7.2 Dimensioning of bolts and rivets
On structural metal work drawings, bolts and rivets can be drawn in a simplified form and indicated
with a leader line. See Figure 12 and Table 4.
12
Copyright British Standards Institution © ISO 2018 – All rights reserved
Uncontrolled copy when printed 00376 BTMXN01, 2019-01-30
Provided by IHS Markit under license with BSI - Uncontrolled Copy Licensee=Bombardier Extract/5957305002
No reproduction or networking permitted without license from IHS Not for Resale, 06/05/2018 11:35:43 MDT
BS ISO 129‑5:2018
ISO 129‑5:2018
Annex A
(normative)
Graphical symbols shall be drawn in accordance with Table A.1. The letter h indicates the height of
dimensions on the drawing, see Figure A.1.
--``,`,,`,,,``,``,,```,``,,```-`-`,,`,,`,`,,`---
3
Channel section/ 4
Thin-walled channel H-beam section
section
5 6
T section Flat bar/Plate
7 8
Single round-headed flats Double round-headed flats
9
10
Unequal round-headed
Chamfered flats
flats
14
Copyright British Standards Institution © ISO 2018 – All rights reserved
Uncontrolled copy when printed 00376 BTMXN01, 2019-01-30
Provided by IHS Markit under license with BSI - Uncontrolled Copy Licensee=Bombardier Extract/5957305002
No reproduction or networking permitted without license from IHS Not for Resale, 06/05/2018 11:35:43 MDT
BS ISO 129‑5:2018
ISO 129‑5:2018
11 12
Diamond section Trapezoidal section
13 14
Angle–square section Oval tube
16
15
Right-angled trapezoid
Slot with round end tube
tube
17
18
Thin-walled equal leg
Scalene channel section
angle with inner edge
19
20
Channel section with
Hat section
inner edge
--``,`,,`,,,``,``,,```,``,,```-`-`,,`,,`,`,,`---
21 22
Z-section Thin-walled lip Z section
23 24
Thin-walled oblique Rectangular hollow
lip Z section section/Rectangle tube
25
P section tube
Annex B
(informative)
--``,`,,`,,,``,``,,```,``,,```-`-`,,`,,`,`,,`---
16
Copyright British Standards Institution © ISO 2018 – All rights reserved
Uncontrolled copy when printed 00376 BTMXN01, 2019-01-30
Provided by IHS Markit under license with BSI - Uncontrolled Copy Licensee=Bombardier Extract/5957305002
No reproduction or networking permitted without license from IHS Not for Resale, 06/05/2018 11:35:43 MDT
BS ISO 129‑5:2018
ISO 129‑5:2018
7 Slot
--``,`,,`,,,``,``,,```,``,,```-`-`,,`,,`,`,,`---
Buying standards PLUS is an updating service exclusive to BSI Subscribing Members. You will
automatically receive the latest hard copy of your standards when they’re
You can buy and download PDF versions of BSI publications, including British revised or replaced.
and adopted European and international standards, through our website at
bsigroup.com/shop, where hard copies can also be purchased. To find out more about becoming a BSI Subscribing Member and the benefits
of membership, please visit bsigroup.com/shop.
If you need international and foreign standards from other Standards Development
Organizations, hard copies can be ordered from our Customer Services team. With a Multi-User Network Licence (MUNL) you are able to host standards
publications on your intranet. Licences can cover as few or as many users as you
Copyright in BSI publications wish. With updates supplied as soon as they’re available, you can be sure your
documentation is current. For further information, email subscriptions@bsigroup.com.
All the content in BSI publications, including British Standards, is the property
of and copyrighted by BSI or some person or entity that owns copyright in the Revisions
information used (such as the international standardization bodies) and has
formally licensed such information to BSI for commercial publication and use. Our British Standards and other publications are updated by amendment or revision.
Save for the provisions below, you may not transfer, share or disseminate any We continually improve the quality of our products and services to benefit your
portion of the standard to any other person. You may not adapt, distribute, business. If you find an inaccuracy or ambiguity within a British Standard or other
commercially exploit, or publicly display the standard or any portion thereof in any BSI publication please inform the Knowledge Centre.
manner whatsoever without BSI’s prior written consent.
Useful Contacts
Storing and using standards Customer Services
Standards purchased in soft copy format: Tel: +44 345 086 9001
• A British Standard purchased in soft copy format is licensed to a sole named Email (orders): orders@bsigroup.com
user for personal or internal company use only. Email (enquiries): cservices@bsigroup.com
• The standard may be stored on more than 1 device provided that it is accessible Subscriptions
by the sole named user only and that only 1 copy is accessed at any one time. Tel: +44 345 086 9001
• A single paper copy may be printed for personal or internal company use only. Email: subscriptions@bsigroup.com
• Standards purchased in hard copy format:
Knowledge Centre
• A British Standard purchased in hard copy format is for personal or internal Tel: +44 20 8996 7004
company use only.
Email: knowledgecentre@bsigroup.com
• It may not be further reproduced – in any format – to create an additional copy.
This includes scanning of the document. Copyright & Licensing
If you need more than 1 copy of the document, or if you wish to share the Tel: +44 20 8996 7070
document on an internal network, you can save money by choosing a subscription Email: copyright@bsigroup.com
product (see ‘Subscriptions’).
BSI Group Headquarters
389 Chiswick High Road London W4 4AL UK
Uncontrolled copy
Not for when printed 00376 BTMXN01, 2019-01-30
Provided by IHS Markit under license with BSI - Uncontrolled Copy Licensee=Bombardier Extract/5957305002
No reproduction or networking permitted without license from IHS Resale, 06/05/2018 11:35:43 MDT